Addonics M2HU9HS-2S
Contents
1. 10 12 BootTime Delay This option is used to set boot delay time Default setting is 5 seconds 10 13 Quick Compare sets Compare function to stop after a small amount of data has been verified up to 100MBytes Default setting is OFF 10 14 Copy with Size Causes duplicate drive to report to an operating system the exact same total size as source when copy is complete Works only on drives formatted using a Master Boot Record Default setting is OFF Phone 408 453 6212 Email www addonics com support query 6 Advanced Setup Options 12 01 Read Error Skip Allows duplicator to ignore I O errors while reading source drive Default setting is OFF 12 02 Update Firmware Used to apply firmware updates Connect a drive formatted as FAT containing one partition with the firmware file in the root directory NOTE This function scans the entire disk before proceeding Providing a drive that is as small as possible is strongly recommended 12 03 Compare Firmware Used to confirm correct firmware Connect a drive formatted as FAT containing one partition with the firmware file in the root directory NOTE This function scans the entire disk before proceeding Providing a drive that is as small as possible is strongly recommended 12 04 Quick Erase HDD scans the ports then quickly erases all sectors on all connected drives 12 05 Full Erase HDD scans the ports then completely erases all sectors on all connected drives 12 06 H W2. Diagnostic Starts comprehensive tests for Ram LCD buttons ports and Flash 12 07 Load Default Resets all configuration settings to default 12 08 Copy HPA Enables copy functions to duplicate the source drive s Host Protected Area Normally this area is defined as not available to a host controller as defined by ATA SATA specifications 12 09 Burn In Runs a function continuously until aborted Selections are Copy amp Compare Compare Async Copy amp Cmp Async Compare www addonics com Phone 408 573 8580 Fax 408 573 8588 Email http www addonics com sales query
3. TECHNOLOGIES User Guide T E i En l ee l ee 8 1 9 M2 SSD HDD HS Duplicator PRO M2HU9HS 2S www addonics com Technical Support If you need any assistance to get your unit functioning properly please have your product information ready and contact Addonics Technical Support at Hours 8 30 am 6 00 pm PST Phone 408 453 6212 Email http www addonics com support query Overview Cooling Fans Control Panel 3 5 Source Source Select Jumper 2 5 Source Targets aoe i serete RH HHTH ats PHHH cate Hoth aa ibaa Power Connector Power Switch sts H Ba dete setetateted oe tt Eis Power Select Power Button WARNING Please remember to set the power supply to your local outlet voltage prior to plugging in the power cord Failure to do so may damage the power supply To Controller Not Used 2 5 Source 3 5 Source Source Select Jumper NOTE The provided jumper MUST be connected between To Controller and either of the two source connectors 2 5 M2 NGFF SSD drive Qty 10 www addonics com Technical Support M F 8 30 am 6 00 pm M 2 Installation Step 1 For 80mm device remove the screw from the 80mm Standoff before proceeding Otherwise place Metal Standoff over mounting hole for 30mm 42mm or 60mm device Note An extra screw and standoff are provided when installing 60mm or 80mm media remove the extr
4. a parts Step 2 Insert the media device into the NGFF connector at an angle Step 3 Secure the device in place with the mounting screw Phone 408 453 6212 80mm Standoff Metal Standoff Email www addonics com support query 2 Connecting the Power Cable and Powering On a Connect the power cord provided from the wall outlet to the back of the tower b Turn on the main power switch on the rear of the chassis c Push the power button on the front of the unit to turn on the HDD duplicator Quick Start By default the duplicator will initialize scan for drives and offer the copy function Insert the source and target drives power up the unit wait for the copy function to appear then press ENT Canceling Functions When selecting menu options canceling is done by pressing ESC When the unit is busy performing an operation such as copy verify or overwrite the operation can be canceled by holding the ESC button until the unit beeps Duplicator Functions The duplicator has three menu sections The Main menu Setup Options and Advanced Setup Options Setup Options is accessed through the Main menu Advanced Setup Options is accessed by holding the ESC button from any other menu until the unit beeps When the duplicator completes some of the functions it will record a log of the most recent activity Select VIEW LOG from the Main Menu to review the latest function s results Main Menu 1 Copy HDD scans the po
5. ata on all HDDs connected to the duplicator including Source HDD by writing data to all sectors There are 4 sub options One pass zero One pass random 3 pass and 7 pass 10 Setup Enters the Setup menu See Setup Options 11 View Log Shows the results from the most recent drive operation such as copy overwrite etc 12 Adv Setup Enters the Advanced Setup Menu Only available by holding ESC on any Main Menu option See Advanced Setup Options Phone 408 453 6212 Email www addonics com support query 4 Setup options 10 1 Language Use this option to select the language of the system currently only English is supported 10 2 Copy Size Controls how much of the source drive to use for copy operations in percentage Default setting is ALL 100 10 3 Startup Menu sets the first menu option to appear after boot Default setting is Copy HDD 10 4 Auto Compare Controls whether or not targets are compared automatically when copy is complete Default setting is OFF 10 5 Button Sound Enables audible beep when pressing buttons Default setting is ON 10 6 Device Info Displays information about connected drives Main display is drive manufacturer and size Press up down to select drives ENT to display model number and firmware revision of selected drive 10 7 System Info Displays firmware version and date 10 8 Fast Copy When this setting is ON the duplicator will attempt to copy the source drive s cont
6. ents instead of the entire disk Also controls Compare function Default setting is OFF NOTE Target drive size is still required to be equal to or greater than source Only works with source drives formatted using Master Boot Record If the source drive has a boot record other than MBR the entire disk will be copied as if Fast Copy were OFF If the source drive is formatted with a Master Boot Record and contains only FAT32 or NTFS partitions identical partitions will be created on the target s and only the files will be copied If the source drive with MBR format includes partitions other than FAT32 or NTFS all sectors of all partitions including FAT32 and NTFS will be duplicated Enabling Fast Copy may not produce bootable duplicates 10 9 Auto Start Drive When source drive is present inserting a target drive will cause copy process to begin automatically Default setting is OFF 10 10 Auto Start Timer sets delay in time after target insertion before beginning auto copy process if Auto Start Drive is ON Default setting is OFF no delay 5 www addonics com Technical Support M F 8 30 am 6 00 pm 10 11 Tolerance Size Sets the minimum target size in percentage compared to the source that is allowed to use for copying Default is 100 equal in size NOTE Leaving this setting at 100 or using for minor adjustments only is strongly recommended Permitting target size less than source size may result in inaccurate copies
7. rts then copies from the source to any targets found 2 Async Copy HDD scans the ports then copies from the source to any targets found More drives may be added before the process is complete they will begin the process as soon as they are detected 3 Compare HDD scans the ports then any targets found will be compared to the source 4 Async Compare scans the ports then any targets found will be compared to the source More drives to compare may be added before the process is complete they will begin the process as soon as they are detected 5 PreScan Source Reads all blocks on the source drive to confirm no I O errors are encountered 6 ReScan BUS Manually scans all ports and reports how many units were found 3 www addonics com Technical Support M F 8 30 am 6 00 pm 7 Source Size Examines the source drive and reports total space and space used if drive contains compatible partitions Press up down to change display ESC to exit 8 Secure Erase Scans all ports then erases all data on all connected drives NOTE some drives will remain in a locked state when the process is complete Drives that are locked may not appear to an operating system and will cause an I O error if used as a target in the duplicator If this happens start secure erase again and hold ESC to cancel the operation a few moments after it begins 9 Overwrite Overwrite is used to write data onto the entire hard disk it will destroy all d
Download Pdf Manuals
Related Search