Gorenje RK60359OX
Contents
1. The setting recommended by the manufacturer is in the middle between the Min and Max signs Any change in the environment temperature will affect the temperature inside the appliance Hence thermostat setting should be adjusted in such cases Setting the thermostat to a position closer to the Max sign increase the temperature cooler setting it to a position closer to the Min sign will decrease the temperature warmer e fthe temperature of the environment in which the appliance is installed is lower than 16 C we recommend setting the thermostat button to the Max position Fan only with some models The fan contributes to more equal distribution of temperature and faster cooling as well as reduces formation of dew on the shelves It only operates when the compressor is activated Turning on the fan is recommended as an additional function in the following cases increased temperature in the room over 30 C increased humidity during the summer when inserting larger quantities of food rapid cooling Turning the fan on off ON J OFF 0 When the fan is on a red dot is indicated on the switch Note When the fan is activated power consumption is increased and temperature in the refrigerator drops Hence we recommend resetting the temperature in the appliance when the fan is activated between Min and dashed line without the fan area between and Max Temperature s2. AN Bottles with high alcohol content should be tightly sealed and stored in an upright position DAN Some organic solutions essential oils in lemon and orange peel butter acid etc may damage the plastic surfaces in case of a prolonged contact causing premature ageing of these materials AN Unpleasant smell warns of poor appliance cleanliness or deteriorated food see Cleaning and Maintenance AN Remove perishables from the refrigerator before a longer period of absence from home The equipment depends on the models The shelves can be inserted to any of the shelf guides in the refrigerator interior They are protected against pulling out To remove a shelf from the refrigerator lift is slightly at the front tilt as required and pull it out Food that perishes quickly should be kept at the back of the shelf where the temperatures are lower Certain models are equipped with wire bottle rack which enables placing of bottles on the cork It is safeguarded against pulling out It may be pulled out only if empty by lifting the front part and pulling it towards you Place the bottle rack in the appliance in such way to avoid obstruction of door closing by the length of the stacked bottles Maximum load of the rack is 9 bottles of 0 75 I or 13 kg of total mass see label at the right side of the interior of the appliance The bin drawer at the bottom of the refrigerator compartment under the glass shelf is intended for
3. 41 v09c We thank you for the confidence you have shown by purchasing our appliance We wish you a lot of pleasure using the appliance The appliance is intended solely for household use The refrigerator freezer hereinafter referred to as the appliance consists of two parts the upper part is the refrigerator compartment and the lower part is the freezer compartment freezer chest The refrigerator compartment is intended for use in households for storing fresh food at temperatures higher than 0 C The freezer is intended for use in households for freezing fresh food and for long term storage of frozen food up to one year depending on the type of food Important warnings eere eere 3 A few tips on how to save power with your refrigerator freezer combo 5 Appliance description 6 Installation and connection 8 Changing the door opening direction 10 Operating the appliance with electronic controls 12 Operating the mechanically controlled appliance 20 Recommended food arrangement in the appliance 26 Storing food in the refrigerator 27 Storage of food in the FreshZone 28 Freezing fresh food and
4. E key When selecting a compartment make sure the recess on the dial is aligned with the indicated area i o FREEZER FRIDGE 260437 4 v09c Switching the appliance on off and setting the temperature EF Switching the appliance on off Use the A switch to choose the freezer compartment Then press and hold for three seconds the E key to switch on the appliance Both the refrigerator and the freezer compartment will be switched on When the appliance is on the B signal light will also be on If the E key is pressed and held for three seconds again the entire appliance will be switched off Switching the refrigerator on off The models with the temperature display allow switching off the refrigerator while the freezer continues to operate First switch on the entire appliance Then select the refrigerator compartment using the A switch Press and hold the E key for three seconds to switch off the refrigerator When the E key is pressed and held for three seconds again the refrigerator will be switched on again Setting the temperature in the appliance Use the A switch to select refrigerator freezer and press the E key to set the desired temperature The settings are changed in circle incrementally from maximum to minimum value or to super freeze freezer boost function for the freezer When the desired temperature is set the setting is automatically saved after five seconds and the current
5. door 4 Unscrew the forced door closure system B and fix it to the opposite side of the door certain models only 5 Unscrew middle hinge screws remove the door from bottom hinge 6 Loosen the screws fixing the leg supports certain models only then continue the procedure either under cf 7 or 7 1 depending on the model of the appliance 7 Tilt the appliance backward max 35 to lean to the rear side of the cabinet Unscrew the leg support screws C left and right and remove the leg support cover D and place it to the opposite side Unscrew and remove then reciprocally replace the position of end switch E and decorative peg F for models with forced door closing system Unscrew three screws fixing the bottom hinge save the hinge for later use and fix the attached bottom hinge on the opposite side 7 1 Tilt the appliance backwards max 35 to lean on the housing at the back Loosen three screws holding the bottom hinge save the hinge for eventual subsequent door swing change On the opposite side affix the attached bottom hinge Plug the holes left after the replacement with relevant pegs 8 Repeat the procedure 3 and 4 on the bottom door In case there is no bottom door limit peg transfer the bearing G and washer to the opposite side of the door 9 Proceed with the assembly procedure in opposite sequence Remark At OLD TIMER appliances alteration of door opening direction is not possible 260
6. food separately or wrap it in suitable packages Be careful to prevent touching of different types of meat They should be packed and stored separately to avoid bacterial decomposition in case meat turns foul Approximately 30 60 minutes prior use remove food from the drawer to let its aroma and taste develop at ambient temperature Food sensitive to low temperatures is not suitable for storage in the FreshZone drawer pineapple avocado bananas olives potato eggplant cucumber beans bell pepper melons water melons pumpkins Freezing procedure m AN Maximum quantity of fresh food that can be introduced into the appliance at a time is indicated on the label with basic information on the appliance If this quantity is exceeded freezing quality will deteriorate as will the quality of the already frozen food 24 hours before freezing fresh food activate the super freeze freezer boost function control unit I rotate the dial A to position SF SUPER control units Il and III Press the E key signal light F will light up control unit IV rotate the dial A to position SF X control unit V with and without fan rotate the dial A to a position between min and max with the fan switched off After 24 hours place the fresh food into the freezer as follows NO FROST appliances place the food into the middle section of the freezer compartment standard appliances place the food into the upper se
7. possible therefore smaller packages should be preferred Before freezing the food should be cooled When storing or using frozen food observe the manufacturer s instructions Temperature and best before date are indicated on the packaging Only choose food with undamaged packaging stored in freezers at temperatures of 18 C or lower Do not buy a food package covered with frost as this is a sign that the food has been slightly thawed several times Such food is of lesser quality When transporting frozen food prevent it from defrosting thawing Higher temperature will result in shorter storage time and deteriorated food quality Recommended time for storage in the freezer Food Time from 4 to 6 months chopped dice or ground meat bread pastry ready to eat meals lean tripes innards smoked sausage fatty fish Microorganisms are not destroyed by freezing After defrosting their activity is resumed intensively and the food may perish quickly Therefore use the thawed food as quickly as possible Partial thawing decreases the nutritive value of the food particularly fruit vegetables and ready to eat food Automatic refrigerator defrosting Defrosting a conventional freezer a Defrosting a NO FROST freezer The refrigerator does not require defrosting as ice accumulated on the back wall of the refrigerator compartment interior is melted automatically The accumulated ice is thawed when the
8. storing fruit and vegetables It provides humidity thus preventing the food from dehydrating The food must be appropriately packaged in order to prevent emitting or receiving smell and moisture 260437 4 v09c Food storage time Interior side of the refrigerator door is fitted with racks and bins intended for storing cheese butter eggs yoghurt and other smaller packages tubes cans etc The lower part of the door is fitted with a bottle rack The rack fitted on the interior side of the freezer compartment door only with some models is intended for storing frozen food that is used often and requires quick access ice cream open packages of frozen vegetables etc Recommended storage time for the refrigerator deserts fruit ready to eat dishes raw meat chunks fish raw chopped meat seafood up to 1 day up to 2 days The FreshZone drawer provides storage of wide selection of fresh food longer than in the traditional refrigerator Food remains fresh for long time and it preserves its taste and nutritive ingredients It reduces decay and loss of mass so fruit and vegetables are more fresh and natural The drawer must be tightly closed to provide optimum operation Moisture level in the drawer depends upon the moisture of stored food and on the frequency of opening the drawer e When you buy food check its freshness quality and durability of food depends on it e Store non wrapped animal or vegetable
9. wall Mind the space required to open the door and pull out the drawers and shelves see installation diagram min 650 mm min 640 mm min 1150 mm min 900 915 mm Remark Applies to OLD TIMER appliances Use the power cord to connect the appliance to the power mains The wall outlet should be fitted with a ground contact safety socket Nominal voltage and frequency are indicated on the label with basic information on the appliance The appliance should be connected to the power mains and grounded in compliance with the relevant effective standards and regulations The appliance will withstand short term deviations from the nominal voltages but not more than from 6 9o to 6 260437 4 v09c Version Tools required ring spanner box end wrench No 8 screwdriver torx25 flathead screwdriver 1 2 3 Use a flathead screwdriver to remove the hole plugs covers A and B1 Unscrew and remove one by one in the specified order from top to bottom the hinges C D and E1 and the door F G Make sure the door is not damaged Move the hole plugs covers H to the opposite side 4 Attach the lower hinge E2 supplied in a bag to the opposite side of the housing and add the 5 washer I Upper door F Move the upper hinge C with the bearing J to the opposite side Remove the door stopper with the hinge K1 and attach a symmetrical door sto
10. 437 LZEvoge Operating the appliance with electronic controls CONTROL UNIT A Temperature setting knob turn on off and SF SUPER CONTROL UNIT Il G C D B EF A A Temperature setting and on off button B Signal light on when the appliance is in operation C Refrigerator sound alarm acknowledgement button D Signal light flashes if refrigerator temperature is too high E Freezer boost button F Signal light on when freezer boost function is activated G Digital refrigerator temperature display displays actual temperature in the appliance in the range from 1 C to 9 C Only with some models No Frost sign only with some models 260437 LZEvoge Switching the appliance on off Selecting the temperature in the appliance To switch on the appliance rotate the A dial towards the max position Signal light B will light up only with some models The appliance is switched off when the position of the recess on the dial is aligned with the D sign there is still voltage in the appliance e Set the desired refrigerator temperature by rotating the A dial in the interval from min to max e Recommended setting is at the eco position Settings towards max position correspond to lower cooler refrigerator temperature and settings towards the min position mean higher temperature warmer e fthe temperature of the room in which the appliance is installed is lower than 16 C we recommend
11. 60437 4 v09c Cleaning the appliance 4 Before cleaning disconnect the appliance from the power mains rotate the thermostat knobs A and B to position 0 and unplug the power cord Use a soft cloth to clean all surfaces Cleaners containing abrasive particles acids or solvents are not appropriate as they will damage the surface Clean the appliance exterior with water or a mild solution of suds Lacquer coated and aluminum surfaces can be cleaned with lukewarm water to which some mild detergent was added Cleaning agents with minor alcohol content are also acceptable e g window cleaners Cleaners with alcohol content are not allowed for cleaning plastic parts Clean the appliance interior with lukewarm water to which you may add some vinegar Placed under the cooling board that cools the refrigerator interior are a trough groove and an opening through which melted water is discharged from the appliance interior The through and the opening should never be blocked therefore check them often and clean as required e g using a plastic straw Frost and ice accumulated in a layer of 3 5 mm will cause an increase in power consumption therefore it should be removed regularly this does not apply to the NO FROST freezer Do not use any sharp objects solvents or sprays Condenser unit on the back of the refrigerator should always be kept clean free of dust or deposit from kitche
12. at all times WARNING Do not use any mechanical accessories or other methods to defrost the appliance except for those expressly recommended by the manufacturer WARNING During installation cleaning and removal of appliance be careful not to damage the insulation of the parts of the cooling system This will also prevent pollution WARNING Do not use any electric devices inside the appliance except for those allowed by the manufacturer of this refrigeration appliance treated as household waste Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment By ensuring this product is disposed of correctly you will help prevent potential negative consequences for the environment and human health which could otherwise be caused by inappropriate waste handling of thisproduct For more detailed information about recycling of this product please contact your local city office your household waste disposal service or the shop where you purchased the product The symbol on the product or on its packaging indicates that this product may not be A few tips on how to save power with your refrigerator freezer combo e Observe the installation instructions Do not open the appliance door more frequently than necessary Occasionally check whether air can circulate freely behind the appliance Condenser unit mounted on the appliance back wall must be kept clean
13. at all times see section Cleaning the appliance e If the seal is damaged or loose replace it as soon as possible e Store your food in closed containers or other appropriate packaging Before placing the food in the refrigerator let it cool down to room temperature Defrost your frozen food in the refrigerator compartment Remove the freezer drawers and door as described in the instructions in order to make use of the entire capacity Defrost your conventional freezer when a frost layer approximately 3 5 millimetres thick has accumulated on the surfaces in the freezer compartment Make sure the shelves are evenly distributed and that the food is arranged in a way that allows free circulation of air heed the recommended food arrangement as described in the instructions n appliances fitted with a fan do not block the fan slots 260437 LZEvOg9e Appliance description A_Refrigerator compartment Control unit 1 2 Interior illumination lamp 3 Shelf height adjustable 4 Fruit and vegetables bin drawer 5 Refrigerator door rack deep and shallow version 6 Bottle rack B Standard freezer standard appliances 7 Freezing drawer 8 Storage drawer 9 Storage drawer 10 Freezer door rack 11 Water discharge groove 12 Foot 13 Wheel B NO FROST freezer 7 Storage drawer 8 Freezing drawer 9 Storage drawer Appliance interior equipment may change subject to appliance model The drawer
14. cked opening e g using a plastic straw e If the layer of ice is too thick defrost the appliance annually see Defrosting the appliance Door is opened too often or too long Door not closed properly foreign object between the door and the housing tilted door damaged seal etc Alonger power failure Too much fresh food inserted at the same time f you wish to open freezer door immediately or shortly after closing it you may feel rather strong resistance When the freezer door is opened some cool air escapes from the freezer compartment and it is replaced by warm air from the environment When this air is cooled a sub pressure builds up causing resistance to door opening After a few minutes the condition is normalized and the door can be easily opened again Blocked water discharge opening or water from thawed ice 260437 LEvOIT Replacing the bulb Before replacing the bulb disconnect the appliance from the power mains unplug the power cord from the wall outlet socket Remove the cover using a screwdriver replace the bulb with a new one E14 same power rating as the one provided by the manufacturer and replace the cover Do not dispose of the blown bulb with organic waste e The bulb is considered a consumable and is excluded from any warranty Bulb lamps used in this appliance are special purpose lamps selected for household appliances use only They are not suitable for househol
15. compressor is not operating The drops will drip through the opening in the refrigerator back wall into a container above the compressor from where they will evaporate If an excessive layer of ice is accumulated on the refrigerator back wall 3 5 mm the appliance should be disconnected and defrosted manually The freezer should be defrosted when approximately 3 5 mm of frost is accumulated 24 hours before defrosting activate the super freeze freezer boost function to additionally cool the food see section Freezing process After 24 hours remove the frozen food from the freezer and protect them from thawing Disconnect the appliance rotate the thermostat knob A and B to the D position and unplug the power cord from the wall outlet Pull out the drain trough on the bottom of the freezer and place a container under it to collect the water from thawed ice and frost Do not use electrical appliances to defrost the appliance hairdryer etc When defrosting the refrigerator do not use any defrosting sprays as these may damage the plastic surfaces or harm your health Clean the appliance interior and wipe it dry see cleaning the appliance Before putting the food back into the freezer connect the appliance to the power mains and rotate the A button back to the desired setting e The NO FROST freezer is defrosted automatically Occasional occurrence of frost will be eliminated automatically 2
16. ction of the freezer compartment Fresh food should not be in contact with the packages of already frozen food In NO FROST freezers there should be a sufficient clearance just under the upper wall in order to allow air circulation Therefore do not place any food higher than the indicated level see figure e When freezing minor quantities of food 1 2 kg the super freeze setting is not required After 24 hours the food can be relocated to other freezer compartment areas or drawers and the freezing process may be repeated with new food if required When the freezing process is complete rotate the dial A back to the desired setting control units I IV and V To use the entire freezer compartment volume remove the middle drawer In standard appliances with energy efficiency class A remove all three drawers 260437 4 v09c Important warnings on freezing fresh food Storing pre frozen food Storage times for frozen food Defrosting frozen food AN The freezer should only be used for freezing food that is appropriate for freezing The food should always be fresh and of adequate quality AN Choose an appropriate packaging for the food and package it correctly AN The packaging should be airtight and watertight to prevent loss of humidity or vitamins from the food AN Indicate the type of food quantity and freezing date on each food package AN It is important that the food is frozen as quickly as
17. d room illumination Signal light B is flashing e f the signal light B is flashing call a service technician Error code displayed certain e If the character E appears on the digital display certain models only models only call service assistance If none of the above reasons seems to match your problem please contact the nearest service center and state the type model and serial number as indicated on the label with basic information attached in the appliance interior Cooling in the refrigerators freezers is enabled by a cooling system with a compressor with some appliances also a fan which emits a certain level of noise during operation The level of noise depends on installation proper use and appliance age e After appliance startup the compressor may be somewhat louder fluid noise noise caused by refrigerant flowing through the system This is not a sign of malfunction and it will not affect the appliance useful life Eventually the level of this noise will be reduced Occasionally sudden or louder noise may appear during appliance operation which will appear uncommon these are mostly the result of improper installation The appliance must be placed horizontally and firmly on a solid base The appliance should not be in contact with the wall or adjacent elements Make sure the appliance interior equipment is appropriately fitted and that the noise is not caused by vibrating cans bottles or other c
18. e Appliance installation should be carried out by at least two persons to avoid any physical injury or damage to the appliance The appliance should stand firmly in an upright position on a sufficiently solid base At the front the appliance is fitted with two adjustable legs that can be used to level the appliance only with some models Rear side of the appliance is fitted with wheels certain models only facilitating the positioning of the appliance at the preselected place e fthere is a kitchen furniture element above the appliance there should be a clearance of at least 5 centimeters between this element and the refrigerator to ensure sufficient cooling of the condenser unit Two spacers attached to the appliance must be fitted onto the upper edge of the condenser thus preventing the appliance from being installed too close to the wall only some models have it Spacers are manufactured for all purpose function depending on the distance of the condenser from the appliance Therefore turn spacers correspondingly and fix them to the appliance Do not expose the appliance to direct sunlight and do not place it near sources of heat If this cannot be avoided install an insulation panel Connecting the appliance e Handles are fitted under the housing at the front side to make moving the appliance easier only with some models The appliance may stand freely or it can be placed next to a kitchen furniture element or a
19. en Min and Max position e Recommended setting for both thermostat knobs is halfway between the Min and Max mark e A change in the environment temperature will also affect the temperature in the appliance Hence thermostat knob setting should be adjusted accordingly Settings closer to the Max mark correspond to lower temperatures in the appliance cooler air and settings closer to the Min position correspond to higher temperatures Red LED D will light up when the temperature in the freezer compartment rises to a level that may be detrimental to the food it will go off as soon as the temperature drops to a safe level see Troubleshooting 260437 LEvoOge CONTROL UNIT V Appliance with a single compressor without a fan A A Temperature setting and on off knob B Illumination on off button Appliance with a single compressor with a fan A Temperature setting and on off knob B Illumination on off button 260437 4 v09c Turning the appliance on off A Setting the appliance temperature Turn on rotate the thermostat knob A in clockwise direction towards the Max position Turn off rotate the thermostat knob A back into a position where the arrow is pointing at the symbol in this case the appliance is still powered e Set the desired refrigerator compartment temperature by rotating the A knob so that the arrow is pointing to a position between the Min and Max sign
20. etting for the refrigerator also affects the temperature in the freezer compartment 260437 4 v09c Recommended food Refrigerator compartment areas arrangement in the upper area canned preserved food bread wine pastry etc appliance medium area dairy products ready to eat meals deserts juices beer cooked food etc lower area meat meat produce delicatessen etc vegetable drawer bin fresh fruit vegetables salads root vegetables potatoes onions garlic tomatoes tropical fruit sauerkraut turnips etc Refrigerator door areas upper medium part eggs butter cheeses etc lower part beverages cans bottles etc Freezer parts door area packed vegetables ice cream ice etc Other areas freezing storing frozen food see Freezing and storing frozen food Important warnings on food storage Refrigerator interior equipment A Appropriate use of the appliance appropriate food packaging maintaining the appropriate temperature and observing the hygienic guidelines will affect decisively the quality of food storage AN Observe the best before dates indicated on the product packaging AN Food stored in the refrigerator should be placed in closed containers or otherwise suitably packed to prevent emitting scent and moisture A Do not store inflammable volatile and explosive substances in the refrigerator
21. in the freezer negative two digit number While the temperature is being set the display will flash indicating the currently selected setting The display will also flash when the freezer temperature rises to a critical level that presents food spoilage hazard 260437 LZEvoge Operating the mechanically controlled appliance CONTROL UNIT IV Appliance with Dual Compressor System Max Dual Compressor System amp SF CN Qe Min GJ c O Min a 9 m MEVS Ann A FREEZER FRIDGE A A CD B A Temperature setting and on off knob for the freezer compartment B Temperature setting and on off knob for the refrigerator compartment C Lighting on off key D Red LED excessive temperature warning Turning the appliance on off Max B Setting the temperature in the appliance D Turning on the freezer rotate the thermostat knob A in clockwise direction towards the Max position Turning off rotate the A knob back until the arrow is aligned with the C symbol the appliance is still powered Turning on the refrigerator rotate the thermostat knob B in clockwise direction towards the Max position Turning off rotate the B knob back until the arrow is aligned with the symbol the appliance is still powered Set the temperature in the freezer compartment by rotating the A knob from Mix to Max position In order to set the refrigerator compartment temperature rotate the B knob betwe
22. n smoke Use a soft non metal brush or a vacuum cleaner to clean the dust periodically Also clean the container above the refrigerator compressor If it was removed for cleaning replace it afterwards Make sure the container is in a horizontal position e After cleaning switch on the appliance and put the food back in After connecting to the power mains the appliance does not operate Cooling system has been working continuously for a long period of time Excessive build up of ice on the back wall of refrigerator interior may result form the following Water is dripping from the refrigerator Signal light D flashes Door won t open easily Make sure the wall outlet is powered and that the appliance is plugged in Too high environment temperature Door is open too often or it is left open too long Door is not closed appropriately there may be dirt between the door and the refrigerator the door may be tilted the seal should be checked etc Too much fresh food was inserted The sensor in the refrigerator A is blocked by fresh food Make sure the air can circulate around the sensor only with some models air circulation behind the appliance and clean the condenser Food or a container are in contact with the refrigerator interior back wall Poor door sealing If the seal is dirty or damaged clean it or replace it is dripping past the water collection trough Clean the blo
23. ontainers in contact with each other WE RESERVE THE RIGHT TO CHANGES THAT TO NOT AFFECT THE APPLIANCE FUNCTIONALITY Instructions for use of the appliance can also be found on our website at www gorenje com lt http www gorenje com gt 260437 HZS3567 HZS3567F HZS3567AFV HZS4066AFV HZS4066F HZF3261AF HZF3267A HZF3767AF HZF3767AFV HZOS3567 HZOS4066 COMBI BASIC 260437 en 10 14
24. pper K2 supplied in a bag to the opposite side Lower door G move the hinges L and the cover M to the opposite side Install attach from bottom up the hinges D C and doors G F Do not forget to install the washers in the same way they were installed before disassembling I Install the covers A and B2 cover B2 from the supplied bag Replacing the handle remove the hole plugs covers unscrew the screws and attach the handle to the opposite side Insert the plugs into the holes on the opposite side Save the elements B1 E1 and K1 in case you need them to change the door opening direction again at a later time Eg G Version Il Changing the door opening direction Required tools socket spanner nr 8 screwdriver torx 25 Caution After unscrewing of before fixing hinges hold the door to prevent it from falling and damaging 1 Remove upper hinge cover save it for eventual later use remove also the cover on the opposite side of the upper hinge cover on the opposite side you will insert the attached cover during the assembly and remove the cover on the opposite side of the upper part of the door 2 Unscrew upper hinge screws and remove the upper door from the middle hinge 3 On the bottom side of the upper door unscrew the swing stopper screws and remove the stopper A Keep this for eventual use later on Fix the attached stopper with its bearing on the opposite side of the
25. rature Thus unnecessary activation of alarm is prevented Acknowledge and turn off the acoustic alarm by pressing the C key The acoustic alarm will be activated every 24 hours if the temperature in the refrigerator is not low enough and there is danger of food spoilage e Signal light D will be switched off automatically when the appliance cools down to a suitable temperature Displays actual temperature in the refrigerator positive singledigit number While changes are made to the set temperature the display will flash and indicate the current setting The display will also flash if the refrigerator temperature is too high and represents food spoilage hazard CONTROL UNIT Ill Appliance with a valve and temperature display P M P wae FREEZER FRIDGE G C D B E F A A Refrigerator freezer compartment selector switch B Signal light on when the appliance is in operation C Freezer sound alarm acknowledgement key D Signal light flashes if freezer temperature is too high E On off and temperature control key F Signal light on when freezer boost function is activated G Digital temperature display displays actual temperature from 1 C to 9 C for the refrigerator compartment and 16 C to 24 C and SF for the freezer compartment Refrigerator freezer Use the A switch to select the compartment whose temperature selector you would like displayed and for which you would like to set the temperature using the
26. s are protected against pulling out If you wish to remove a drawer pull it out as far as it will go then lift its front part and pull it out completely Only with some models A Refrigerator compartment 1 Control unit 2 Interior illumination lamp 3 Shelf height adjustable 4 Fruit and vegetables bin drawer 5 Refrigerator door rack deep and shallow version 6 Bottle rack B Standard freezer standard appliances 7 Freezing drawer 8 Storage drawer 9 Storage drawer 10 Freezer door rack 11 Water discharge groove 12 Foot 13 Wheel B NO FROST freezer 7 Storage drawer 8 Freezing drawer 9 Storage drawer Appliance interior equipment may change subject to appliance model The drawers are protected against pulling out If you wish to remove a drawer pull it out as far as it will go then lift its front part and pull it out completely Only with some models 260437 LZEvO9e Installation and connection Selecting the room e The appliance should be installed in a dry and well ventilated room The appliance will operate correctly if the environment temperature is within the ranges listed in the table below The appliance class is indicated on the label with the basic information on the appliance Class Temperature SN subnormal from 10 C to 32 C N normal from 16 C to 32 C ST subtropical from 16 C to 38 C T tropical from 16 C to 43 C Installing the applianc
27. setting the thermostat dial to the max position G Freezer boost EF f your appliance is fitted with a digital display it will flash while changes are made to the temperature setting and the currently set temperature will be indicated When the flashing stops the setting is saved and automatically stored When the appliance is switched on for the first time temperature 9 C is displayed and display flashes This value is displayed until temperature in the refrigerator drops below this value Then the flashing will stop and the actual temperature in the refrigerator will be displayed Use this setting after switching on the appliance for the first time before cleaning or when inserting a large amount of food into the freezer If the function is not deactivated manually it will be deactivated automatically after approximately two days 260437 LEvO9IT High refrigerator temperature alarm Digital display If the temperature is too high acoustic alarm will be activated intermittent beep and the D signal light will flash In models with a display unit temperature display 9 C will flash as well The alarm will be switched off automatically as soon as the temperature in the fridge drops to a level that no longer presents spoilage hazard When the appliance is switched on for the first time there is a 24 hour delay in temperature alarm operation to allow the appliance would to reach an adequate tempe
28. storing frozen food 29 Defrosting the appliance 31 Cleaning the appliance 32 Troubleshooting ien reno eio e eoe o eio nnna 33 Information on appliance noise 35 This appliance can be used by children aged from 8 years and above and persons with reduced physical sensory or metal capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved Children shall not play with the appliance Cleaning and user maintenance shall not be made by children without supervision Before connecting the appliance carefully read the instructions for use which describe the appliance and its correct and safe use The instructions apply to several types models therefore they may include descriptions of settings and equipment that may not be available in your refrigerator The instructions also apply to the NO FROST version of the freezer featuring a built in fan and automatic defrosting Remove the packaging that is intended for protecting the appliance or its respective parts during transport Spacers are fitted in the corners of the doors these should be removed and the plugs attached only with some models should be inserted into the openings Before connecting to the power mains the appliance sho
29. temperature in the selected compartment is displayed Super freeze freezer boost Use the A switch to select the freezer compartment Briefly press the E key several times until SF is selected and wait for five seconds until the F light will light up If this setting is not deactivated manually it will be activated automatically after approximately two days Use this setting after switching on the appliance for the first time before cleaning and when inserting major quantities of food into the freezer High freezer temperature alarm C D Digital display If the temperature inside the refrigerator is too high an acoustic alarm will be activated intermittent beep and the signal light D will flash Deactivate the alarm by pressing the C key Signal light D will go off when the freezer temperature drops to a level that no longer presents food spoilage hazard Acoustic alarm will be activated every 24 hours if the freezer temperature is still not low enough and there is danger of food spoilage Sound alarm will be deactivated automatically when the freezer temperature drops to a level that no longer presents food spoilage hazard After switching on the appliance for the first time there is a 24 hour delay in the temperature alarm operation to allow the freezer to reach the set temperature and to prevent unnecessary alarm activation Displays actual temperature in the refrigerator positive single digit number or
30. uld be left to stand still in upright position for at least 2 hours Thus operation errors due to the effect of transport on the cooling system will be much less likely to occur The appliance must be connected to the power mains and grounded in compliance with the effective standards and regulations The appliance may not be used outdoors and should not be exposed to rain The appliance must be disconnected from the power mains unplug the power cord from the wall outlet before cleaning or before replacing the bulb If the power cord is damaged it should be replaced by a service technician or other authorized person 260437 LEvO9IT If the appliance is not used for a longer period of time switch it off with the relevant button and disconnect it from the power mains Empty the appliance defrost it clean it and leave the door ajar To protect the environment dispose of the appliance after its useful life by taking it to an authorized waste collection center The packaging is made of environment friendly materials that can be recycled disposed of or destroyed without hazard to the environment Children should not play with the appliance The label with basic information on the appliance is attached in the appliance interior If the label is not in your local language replace it with the one supplied with the appliance WARNING Ventilation openings on the appliance or built in cupboard must be kept clean and unobstructed
Download Pdf Manuals
Related Search