Tripp Lite B126-2A0
Contents
1. TRIPP LITE HDMI OVER Cat5 EXTENDER Pole Mount 13 08 043 93 32D0 indd 4 8 28 2013 2 17 37 PM Standard 1 x 2 Extender Kit Installation Notes 1 Test to make sure that the entire installation works properly before running cables through ceilings walls 2 24 AWG solid wire Cat5e 6 cable such as Tripp Lite s N202 Series is required to achieve maximum distance and resolution 3 The diagram below shows the maximum extension distance when using Cat6 cabling When using Cat5 cabling the maximum extension distance is 175 ft at 1080i 60Hz and 125 ft at 1080p 60Hz2 4 The B126 2A1 is set to transmit a stereo audio signal by default Press the Audio button on the transmitter unit to switch to 7 1 channel surround sound audio 7 1 channel surround sound signal will be Multi Channel or PCM OPTIONAL LOCAL MONITOR MONITOR 1 MONITOR 2 BLU RAY Up to 200 ft at 1080i 60Hz Cat6 Up to 150 ft at 1080p 60Hz Cat6 13 08 043 93 32D0 indd 5 8 28 2013 2 17 38 PM Standard 1 x 2 Extender Kit Installation Make sure all devices being connected are powered OFF E Connect the HDMI source to the INPUT port on the transmitter unit using a Tripp Lite P568 Series High Speed HDMI Cable 3 Optional Connect a monitor to the LOCAL port on the transmitter unit using a Tripp Lite P568 Series High Speed HDMI Cable 4 Connect the external power supply to the transmitter unit and plug the transm2. oe HDMI Over Cat5 1x2 Extenders Models B126 2A1 B126 2A0 Package Contents 2 Product Features 2 Mounting Instructions 4 Standard 1 x 2 Extender Kit Installation 5 1 x 2 Extender Kit with Remote Repeater Installation T Standard Extender Splitter Installation 10 Extender Splitter with Remote Repeater Installation 13 Troubleshooting 17 Warranty amp Warranty Registration 19 TRIPP LITE 1111 W 35th Street Chicago IL 60609 USA www tripplite com support Copyright 2013 Tripp Lite All rights reserved 13 08 043 93 32D0 indd 1 8 28 2013 2 17 35 PM Package Contents e B126 2A1 Kit or B126 2A0 Receiver Unit e External Power Supply Input 100 240V 50 60Hz 0 5A Output 5V 2A e Mounting Hardware e Screwdriver for Equalization Adjustment e Owners Manual Product Features e Extends an HDMI signal to 2 monitors up to 200 ft from the source over a single Cat5e 6 cable e A B126 002 or B126 004 extender splitter transmitter unit is required for use with the B126 1A0 1x2 receiver unit e Extends a 1080p 6OHZz signal up to 150 ft from the source using Cat6 cabling or up to 125 ft using Cat5 cabling e Extends a 1080i 6OHz signal up to 200 ft from the source using Cat6 cabling or up to 175 ft using Cat5 cabling e Use 24 AWG solid wire Cat5e 6 cable such as Tripp Lite s N202 Series to achieve maximum distance and resolution e Further expand the range and number of monitors by adding B
3. replacing at its sole option any such defective products To obtain service under this warranty you must obtain a Returned Material Authorization RMA number from TRIPP LITE or an authorized TRIPP LITE service center Products must be returned to TRIPP LITE or an authorized TRIPP LITE service center with transportation charges prepaid and must be accompanied by a brief description of the problem encountered and proof of date and place of purchase This warranty does not apply to equipment which has been damaged by accident negligence or misapplication or has been altered or modified in any way EXCEPT AS PROVIDED HEREIN TRIPP LITE MAKES NO WARRANTIES EXPRESS OR IMPLIED INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE Some states do not permit limitation or exclusion of implied warranties therefore the aforesaid limitation s or exclusion s may not apply to the purchaser EXCEPT AS PROVIDED ABOVE IN NO EVENT WILL TRIPP LITE BE LIABLE FOR DIRECT INDIRECT SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OF THIS PRODUCT EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE Specifically TRIPP LITE is not liable for any costs such as lost profits or revenue loss of equipment loss of use of equipment loss of software loss of data costs of substitutes claims by third parties or otherwise WARRANTY REGISTRATION Visit www tripplite com warranty today to register the warranty for your new Tripp
4. 126 110 repeater units e Add up to three repeaters on each Cat5e 6 channel for a total of 4 displays per channel An Active remote receiver should be the last unit in a channel e A 1080p 60HZ signal can be extended up to 125 ft for each repeater added into a channel or up to 175 ft for a 1080i 60Hz signal when using either Catbe or Cat6 cabling e Supports 24 bit True Color 8 bits per channel e Built in equalization control to adjust the video image 2 13 08 043 93 32D0 indd 2 8 28 2013 2 17 35 PM Product Features e Supports both stereo and 7 1 channel surround sound audio 7 1 channel surround sound signal will be Multi Channel or PCM e HDCP and 3D compatible e Plug and play No software or drivers required e Compatible with all operating systems e Mounting hardware included Optional Accessories e B126 110 Remote Repeater Unit e N202 Series Cat6 24 AWG Solid Wire Patch Cables e P568 Series High Speed HDMI Cables 13 08 043 93 32D0 indd 3 8 28 2013 2 17 35 PM Mounting Instructions The B126 2A1 and B126 2AO0 come with mounting hardware that allows them to be mounted in a variety of ways The following images show the different ways the included mounting brackets can be attached for different mounting methods Note The images below show a B126 1A1 HDMI over Cat5 Receiver Unit but the mounting hardware installation is the same for the B126 2A1 and B126 2A0 Wall mount 1 Wall mount 2
5. A0 B126 004 OPTIONAL LOCAL MONITOR a Make sure all devices being connected are powered OFF connect the HDMI source to the INPUT port on a B126 002 or B126 004 transmitter unit using a Tripp Lite P568 Series High Speed HDMI Cable Optional for B126 004 Connect a monitor to the LOCAL port on the transmitter unit using a Tripp Lite P568 Series High Speed HDMI Cable 4 Connect the external power supply to the transmitter unit and plug the transmitter unit into a Tripp Lite Surge Suppressor Power Distribution Unit PDU or Uninterruptible Power Supply UPS The green RJ45 LEDs on the B126 002 and B126 004 and the red power LED on the B126 004 will illuminate to indicate that the unit is receiving power from the external power supply 5 Using Cat5e 6 cable connect a RJ45 OUTPUT port on the transmitter unit to the RJ45 INPUT port on the B126 2A0 1x2 receiver unit 6 Repeat step 5 to add receiver units to the remaining RJ45 OUTPUT ports on the transmitter unit 11 13 08 043 93 32D0 indd 11 8 28 2013 2 17 40 PM Standard Extender Splitter Installation z Connect the external power supply to the receiver unit and plug the receiver unit into a Tripp Lite Surge Suppressor Power Distribution Unit PDU or Uninterruptible Power Supply UPS The green RJ45 LED illuminates to indicate that the unit is receiving power from the external power supply 8 Connect a monitor to the OUTPUT 1 port on the receiver unit using
6. Lite product You ll be automatically entered into a drawing for a chance to win a FREE Tripp Lite product No purchase necessary Void where prohibited Some restrictions apply See website for details WEEE Compliance Information for Tripp Lite Customers and Recyclers European Union Under the Waste Electrical and Electronic Equipment WEEE Directive and implementing regulations when customers buy new electrical and electronic equipment from Tripp Lite they are entitled to a Send old equipment for recycling on a one for one like for like basis this varies depending on the country e Send the new equipment back for recycling when this ultimately becomes waste 19 13 08 043 93 32D0 indd 19 8 28 2013 2 17 42 PM FCC Notice Class B This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Note This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to rad
7. PDU or Uninterruptible Power Supply UPS The green power and the green RJ45 LEDs will illuminate to indicate that the unit is receiving power from the external power supply 8 13 08 043 93 32D0 indd 8 8 28 2013 2 17 39 PM 1 x 2 Extender Kit with Remote Repeater Installation To add a third remote repeater unit repeat steps 8 through 10 To finish your installation with the B126 2A1 receiver unit proceed to step 11 FI Using Cat5e 6 cable connect the RJ45 port on the repeater unit marked OUTPUT to the RJ45 port on the receiver unit marked INPUT 12 Connect a monitor to the OUTPUT 1 port on the receiver unit using a Tripp Lite P568 Series High Speed HDMI cable 13 Repeat step 12 for the OUTPUT 2 port on the receiver unit 14 Connect the external power supply to the receiver unit and plug the receiver unit into a Tripp Lite Surge Suppressor Power Distribution Unit PDU or Uninterruptible Power Supply UPS The green RJ45 LED illuminates to indicate that it is receiving power from the external power supply BE Turn on the power to the connected devices The orange RJ45 LEDs on all units will illuminate to indicate that a signal is being received from the HDMI source The video image will now be displayed on the connected monitors 16 If necessary use the Equalization control on the repeater and receiver units to adjust the video image Note An improper Equalization setting can cause the monitor not to display an
8. a Tripp Lite P568 Series High Speed HDMI Cable O Repeat step 8 for the OUTPUT 2 port on the receiver unit E Turn on the power to the connected devices The orange RJ45 LEDs on the transmitter and receiver units will illuminate to indicate that a signal is being received from the HDMI source The video image should now be displayed on the connected monitors 11 If necessary use the Equalization control on the receiver unit to adjust the video image Note An improper Equalization setting can cause the monitor not to display an image at all Try each setting until an acceptable image is displayed 12 13 08 043 93 32D0 indd 12 8 28 2013 2 17 40 PM Extender Splitter with Remote Repeater Installation Notes 1 Test to make sure that the entire installation works properly before running cables through ceilings walls 2 The diagram below shows the maximum extension distance when using either Cat5e or Cat6 cabling 24 AWG solid wire Cat5e 6 cable such as Tripp Lite s N202 Series is required to achieve maximum distance and resolution 3 The B126 002 and B126 004 are set to transmit a stereo audio signal by default Press the Audio button on the transmitter unit to switch to 7 1 channel surround sound audio 7 1 channel surround sound signal will be Multi Channel or PCM 4 The diagram below shows the B126 004 transmitter unit Installation is the same for the B126 002 except that there are only two output ports and no l
9. ble 4 Connect the external power supply to the transmitter unit and plug the transmitter unit into a Tripp Lite Surge Suppressor Power Distribution Unit PDU or Uninterruptible Power Supply UPS The green RJ45 LEDs on the B126 002 and B126 004 and the red LED on the B126 004 will illuminate to indicate that the unit is receiving power from the external power supply 1 13 08 043 93 32D0 indd 14 8 28 2013 2 17 41 PM Extender Splitter with Remote Repeater Installation 5 Using Cat5e 6 cable connect a RJ45 OUTPUT port on the transmitter unit to the RJ45 INPUT port on the B126 110 repeater unit O connect a monitor to the HDMI OUTPUT port on the repeater unit using a Tripp Lite Po gt 68 Series High Speed HDMI Cable a Connect the external power supply to the remote repeater unit and plug the remote repeater unit into a Tripp Lite Surge Suppressor Power Distribution Unit PDU or Uninterruptible Power Supply UPS The green power and RJ45 LEDs will illuminate to indicate that the unit is receiving power from the external power supply Up to 4 units can be daisy chained 3 repeaters and 1 active receiver To add additional repeater units proceed to step 8 To finish your installation with a B126 2A0 1x2 receiver unit proceed to step 11 8 Using Cat5e 6 cable connect the RJ45 port on the repeater unit marked OUTPUT to the RJ45 port on a second repeater unit marked INPUT connect a monitor to the HDMI OUTPUT port on
10. ch Tripp Lite s HDMI over Cats extenders are tested to support up to 1080p 60HZz video resolution See the Product Features section or the installation diagrams in this manual for details on the maximum distance and resolution when using the repeater and the different receivers The shorter the extension distance the higher the resolution you will be able to obtain If you are not able to get an acceptable image after adjusting the Equalization setting try lowering your computer s video resolution or adjusting the refresh rate 17 13 08 043 93 32D0 indd 17 8 28 2013 2 17 41 PM Troubleshooting 5 What type of cabling are you using Inferior cabling can result in poor performance so it is important that you use cables that support the video resolution you are trying to obtain To achieve maximum distance and resolution 24 AWG solid wire UTP cable must be used Tripp Lite s N202 Series Cat6 Cables are made with 24 AWG solid wire as are the NO22 O1K GY Cat5 and N222 01K GY Bulk Cables Also the HDMI cables you are using must support the resolution you are trying to obtain Inexpensive low quality HDMI cables may not support the maximum resolution It is recommended that you use Tripp Lite s P568 Series High Speed HDMI Cables that are pre tested to work with all B126 Series extender products O test your cables to ensure they are working properly Iry connecting your HDMI cables between a source and monitor that you know w
11. image at all Try each setting until an acceptable image is displayed 13 08 043 93 32D0 indd 9 8 28 2013 2 17 40 PM Standard Extender Splitter Installation Notes 1 Test to make sure that the entire installation works properly before running cables through ceilings walls 2 24 AWG Solid Wire Cat5e 6 cable such as Tripp Lite s N202 Series is required to achieve maximum distance and resolution 3 The diagram below shows the maximum extension distance when using Cat6 cabling When using Cat5 cabling the maximum extension distance is 175 ft at 1080i 6OHZ and 125 ft at 1080p 60HZ 4 The B126 002 and B126 004 are set to transmit a stereo audio signal by default Press the Audio button on the transmitter unit to switch to 7 1 channel surround sound audio 7 1 channel surround sound signal will be Multi Channel or PCM 5 The diagram below shows the B126 004 transmitter unit Installation is the same for the B126 002 except that there are only two output ports and no local monitor port 6 Although the installation instructions below mention the B126 2A0 1x2 receiver unit only Tripp Lite offers several standard receiver units that can be used in the event that only one monitor is required on the remote end B126 1A0 B126 1A0 WP 1 B126 1P0O and B126 1PO WP 1 10 13 08 043 93 32D0 indd 10 8 28 2013 2 17 40 PM Up to 200 ft at 10801 60Hz Cat6 Up to 150 ft at 1080p 60Hz Cat B126 2A0 B126 2A0 B126 2
12. io communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help Any changes or modifications to this equipment not expressly approved by Tripp Lite could void the user s authority to operate this equipment WARNING Use of this equipment in life support applications where failure of this equipment can reasonably be expected to cause the failure of the life support equipment or to significantly affect its safety or effectiveness is not recommended Do not use this equipment in the presence of a flammable anesthetic mixture with air oxygen or nitrous oxide Tripp Lite follows a policy of continuous improvement Product specifications are subject to change without notice TRIPP LITE Excellence 1111 W 35th Street Chicago IL 60609 USA www tripplite com support 13 08 043 9332D0_RevA 13 08 043 93 32D0 indd 20 8 28 2013 2 17 42 PM
13. itter unit into a Tripp Lite Surge Suppressor Power Distribution Unit PDU or Uninterruptible Power Supply UPS The green RJ45 LED illuminates to indicate that the unit is receiving power from the external power supply 5 Using Cat5e 6 cable connect the RJ45 port on the transmitter unit marked OUTPUT to the RJ45 port on the receiver unit marked INPUT O Connect the external power supply to the receiver unit and plug the receiver unit into a Tripp Lite Surge Suppressor Power Distribution Unit PDU or Uninterruptible Power Supply UPS The green RJ45 LED illuminates to indicate that the unit is receiving power from the external power supply E Connect a monitor to the OUTPUT 1 port on the receiver unit using a Tripp Lite P568 Series High Speed HDMI cable 8 Repeat step 7 for the OUTPUT 2 port on the receiver unit O un on the power to the connected devices The orange RJ45 LED s on the transmitter and receiver units illuminate to indicate that a signal is being received from the HDMI source The video image will now be displayed on the connected monitors 10 If necessary use the Equalization control on the receiver unit to adjust the video image Note An improper Equalization setting can cause the monitor not to display an image at all Try each setting until an acceptable image is displayed 6 13 08 043 93 32D0 indd 6 8 28 2013 2 17 38 PM 1 x 2 Extender Kit with Remote Repeater Installation Notes 1 Test
14. ocal monitor port 5 Although the installation instructions below mention the B126 2A0O 1x2 receiver unit only Tripp Lite offers two additional active receivers that can be used in the event that only one monitor is needed at the end of a repeater chain B126 1A0 and B126 1AO WP 1 13 13 08 043 93 32D0 indd 13 8 28 2013 2 17 40 PM Extender Splitter with Remote Repeater Installation Up to 175 ft at 1080i 60Hz Up to 175 ft at 1080i 60Hz Up to 125 ft at 1080p 60Hz Up to 125 ft at 1080p 60Hz Ga oe Bes oe Pete each a B126 110 2a B126 110 REMOTE B126 110 REMOTE B126 2A0 REPEATER REPEATER REPEATER REMOTE RECEIVER Geeta Ba oe Pte ee a B126 110 es B126 110 REMOTE B126 110 REMOTE B126 2A0 Lait REPEATER REPEATER REPEATER REMOTE RECEIVER R Be TA u PE Pte ee Me B126 004 LOCAL TANNE BL o B126 110 as B126 110 REMOTE B126 110 REMOTE B126 2A0 REPEATER REPEATER REPEATER REMOTE RECEIVER OPT MONTOR ge ENED otee ENED oee AA H BLU RAY B126 110 REMOTE B126 110 REMOTE B126 110 REMOTE B126 2A0 REPEATER REPEATER REPEATER REMOTE RECEIVER Gi Make sure all devices being connected are powered OFF connect the HDMI source to the INPUT port on a B126 002 or B126 004 transmitter unit using a Tripp Lite P568 Series High Speed HDMI Cable optional for B126 004 Connect a monitor to the LOCAL port on the transmitter unit using a Tripp Lite Po gt 68 Series High Speed HDMI Ca
15. orks to see if the cable is functioning For Catbe 6 cabling connect it between a computer and a network to verify that it establishes a network connection do you have any patch panels or other devices in between the transmitter repeater and receiver units Tripp Lite s HDMI over Cat5 extender products are designed to be connected directly from the transmitter to the repeater and or receiver via UTP cable The more connection points that are in between the source and the remote monitor the more likely signal degradation will occur causing poor performance If you have a patch panel or if another device is being used it should be removed from the installation 8 Check your cabling for any damages that may have occurred during installation If a cable connector is loosened as a result of being pulled through ceilings walls or the cable jacket is damaged causing the wiring to be exposed you will not achieve maximum performance O Are the transmitter repeater and or receiver located in an area that exposes them to higher temperatures If the product is overheated it will not function properly 18 13 08 043 93 32D0 indd 18 8 28 2013 2 17 41 PM Warranty amp Warranty Registration 1 Year Limited Warranty TRIPP LITE warrants its products to be free from defects in materials and workmanship for a period of one 1 year from the date of initial purchase TRIPP LITE s obligation under this warranty is limited to repairing or
16. the repeater unit using a Tripp Lite P568 Series High Speed HDMI Cable 10 Connect the external power supply to the remote repeater unit and plug the remote repeater unit into a Tripp Lite Surge Suppressor Power Distribution Unit PDU or Uninterruptible Power Supply UPS The green power and green RJ45 LEDs will illuminate to indicate that the unit is receiving power from the external power supply To add a third remote repeater unit repeat steps 8 through 10 To finish your installation with a B126 2A0 1x2 receiver unit proceed to step 11 15 13 08 043 93 32D0 indd 15 8 28 2013 2 17 41 PM Extender Splitter with Remote Repeater Installation 11 Using Cat5e 6 cable connect the RJ45 port on the repeater unit marked OUTPUT to the RJ45 port on the B126 2A0 receiver unit marked INPUT 12 Connect a monitor to the OUTPUT 1 port on the receiver unit using a Tripp Lite P568 Series High Speed HDMI Cable 13 Repeat step 12 for the OUTPUT 2 port on the receiver unit 14 Connect the external power supply to the receiver unit and plug the receiver unit into a Tripp Lite Surge Suppressor Power Distribution Unit PDU or Uninterruptible Power Supply UPS The green RJ45 LED illuminates to indicate that it is receiving power from the external power supply 15 Repeat steps 5 through 14 for each additional RJ45 OUTPUT port on the transmitter unit A turn on the power to the connected devices The orange RJ45 LEDs on all units
17. the transmitter unit and plug the transmitter unit into a Tripp Lite Surge Suppressor Power Distribution Unit PDU or Uninterruptible Power Supply UPS The green RJ45 LED illuminates to indicate that the unit is receiving power from the external power supply 5 Using Cat5e 6 cable connect the RJ45 port on the transmitter unit marked OUTPUT to the RJ45 port on the B126 110 repeater unit marked INPUT O connect a monitor to the HDMI OUTPUT port on the repeater unit using a Tripp Lite P568 Series High Speed HDMI Cable 2 Connect the external power supply to the repeater unit and plug the repeater unit into a Tripp Lite Surge Suppressor Power Distribution Unit PDU or Uninterruptible Power Supply UPS The green power and the green RJ45 LEDs will illuminate to indicate that the unit is receiving power from the external power supply Up to 4 units can be daisy chained 3 repeaters and 1 active receiver To add additional repeater units proceed to step 8 To finish your installation with the B126 2A1 receiver unit proceed to step 11 8 Using Cat5e 6 cable connect the RJ45 port on the repeater unit marked OUTPUT to the RJ45 port on a second repeater unit marked INPUT O connect a monitor to the HDMI OUTPUT port on the repeater unit using a Tripp Lite P568 Series High Speed HDMI Cable 10 Connect the external power supply to the repeater unit and plug the repeater unit into a Tripp Lite Surge Suppressor Power Distribution Unit
18. to make sure that the entire installation works properly before running cables through ceilings walls 2 The diagram below shows the maximum extension distance when using either Cat5e or Cat6 cabling 24 AWG solid wire Cat5e 6 cable such as Tripp Lite s N202 Series is required to achieve maximum distance and resolution 3 The B126 2A1 is set to transmit a stereo audio signal by default Press the Audio button on the transmitter unit to switch to 7 1 channel surround sound audio 7 1 channel surround sound signal will be Multi Channel or PCM Up to 175 ft at 1080i 60Hz Up to 175 ft at 1080i 60Hz OPTIONAL LOCAL Up to 125 ft at 1080p 60Hz Up to 125 ft at 1080p 60Hz MONITOR i Up to 175 ft at 1080i 60Hz MONITOR 1 MONITOR 2 BLU RAY Up to 125 ft at 1080p 60Hz oO cooo B126 2A1 REMOTE t B126 110 REMOTE B126 110 REMOTE B126 110 REMOTE Up to 175 ft at 1080i 60Hz REPEATER REPEATER REPEATER Up to 125 ft at 1080p 60Hz SJ OO B Gi Make sure all devices being connected are powered OFF 2 Connect the HDMI source to the INPUT port on the transmitter unit using a Tripp Lite P568 Series High Speed HDMI Cable optional Connect a monitor to the LOCAL port on the transmitter unit using a Tripp Lite P568 Series High Speed HDMI Cable 13 08 043 93 32D0 indd 7 8 28 2013 2 17 39 PM 1 x 2 Extender Kit with Remote Repeater Installation 4 Connect the external power supply to
19. will illuminate to indicate that a signal is being received from the HDMI source The video image should now be displayed on the connected monitors 17 If necessary use the Equalization control on the repeater and receiver units to adjust the video image Note An improper Equalization setting can cause the monitor not to display an image at all Try each setting until an acceptable image is displayed 16 13 08 043 93 32D0 indd 16 8 28 2013 2 17 41 PM Troubleshooting If you are unable to get an acceptable image after following the installation instructions try these troubleshooting tips Dare the external power supplies that came with the product connected and plugged into a working power source For the product to function properly it must be connected to and receiving power from the external power supply was the power to the connected devices turned off prior to installation If not restart them a Have you adjusted the Equalization setting on the repeater and or receiver units There are built in Equalization adjustment knobs on every repeater and active receiver that can be adjusted to obtain the best picture quality Use the mini screwdriver included with the product to adjust this setting until an acceptable image is displayed Note An improper Equalization setting can cause the monitor not to display an image at all Try each setting until an acceptable image is displayed O what resolution are you trying to rea
Download Pdf Manuals
Related Search