ACTi B53 surveillance camera
Contents
1. www acti com ACTI Connecting Vision vA Hardware Manual 4 Remove the shroud from the dome cover 5 Place the shroud on the replacement dome cover 6 Insert the replacement dome cover into the cover housing 7 Align and attach the three 3 screws to secure the bracket to the cover housing www acti com ACTI _ Connecting Vision WA da Hardware Manual 8 Attach the dome cover to the camera by tightening the three 3 screws Final installation should look similar to the illustration below 2 gt ACTi Connecting Vision Hardware Manual Using a Memory Card The camera supports local video recording or saving of snapshots to a memory card NOTE Supports microSDHC and microSDXC cards How to Insert the Memory Card Insert a memory card into the card slot with the metallic contacts facing down the camera Push the card until it clicks into place How to Remove the Memory Card In case there is a need to remove the card make sure to access the camera Web Configurator to safely unmount the card first see the camera Firmware manual for more information Once unmounted from the firmware push the card to eject it from the slot 30 Bd ACTi Connecting Vision Hardware Manual Accessing the Camera Configure the IP Addresses In order to be able to communicate with the camera from your2. 5 Set the prepared power adapter for connection later Below is an example of a power adapter with an attached terminal block NOTE The power adapter is not bundled in the package 9 Pq ACTI Connecting Vision Hardware Manual Prepare the DI DO and Audio Input Output Connector Optional Depending on your surveillance needs you may connect digital input output or audio input output devices to your camera The camera comes with one 1 terminal block for both digital and audio input output devices How to Connect DI DO Devices Digital Input DI devices can be used to notify the camera about an activity in the camera site DI can be triggers of events For example you can connect a panic button to the camera as such when the panic button is pressed the alarm signal will be sent through the camera Other common DI device applications are emergency button smoke detector passive infrared sensor etc Digital Output DO devices are external devices that are activated by the camera upon an event inside the camera For example you can connect an alarm horn to the camera as such when an event occurs inside the camera e g detected intruder the alarm horn will sound Other common DO device applications are motion triggered lights electric fence magnetic door locks etc Press and hold the orange tab as you insert the wire through the pin slot then release the orange tab to secure
3. ACTI Connecting Vision vA Hardware Manual Use the default IP address of a camera If there is no DHCP server in the given network the user may have to assign the IP addresses to both PC and camera manually to make sure they are in the same network segment When the camera is plugged into network and it does not detect any DHCP services it will automatically assign itself a default IP 192 168 0 100 Whereas the default port number would be 80 In order to access that camera the IP address of the PC has to be configured to match the network segment of the camera Manually adjust the IP address of the PC In the following example based on Windows 7 we will configure the IP address to 192 168 0 99 and set Subnet Mask to 255 255 255 0 by using the steps below me lt All Control Panel Items Network and Sharing Center A E a Vian cad E een eed es Control Panel Home i i ra o a Di ais Di View your basic network information and set up connections rganize v isable this network device iagnos Ch P EE ae See full map Er 7 a A Jo bo Kx Local Area Connection Ch d d shari J ae e SISO_NP_PC1 Network Internet Ue rn This computer ae Intel R 8 i Disable View your active networks Connect or disconnect Status Diagnose jp Network Access type Internet Work network Connections g Local Area Connection B Bridge Connections Create Shortcut Change your networki
4. Indoor Dome Series Hardware Manual B51 B52 B53 2014 01 06 ACTI Connecting Vision Va lt gt Pp ACTI Connecting Vision Hardware Manual Table of Contents EC NS eenn E A Safety Instructions asssnsnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn nnmnnn denna 6 i OGUGNON oinin aia 7 The LISTOI Wi OGG IG nnn EEEE a 7 Package Coments siia 8 Physical Description s ssssnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn nnnm 9 Mounting ODUOINS eieaa iiaae a Enine aeaiiai 11 Other MOUNTING ACCESSOM CS nnee 13 Before INSTAAN 14 Prepare the Power Adapter Optional eenen 14 Prepare the DI DO and Audio Input Output Connector Optional 16 How to Connect DI DO Devices unu ennen ennen en venen venen venen ven 16 How 10 Connect Audio DEVICES seriesas 19 Installing the Camera on a Surface 20 Step 1 Drill th HOIGS sssini ainni 20 Step 2 Open the Dome Cover ennen 21 Step 3 Install the Camera to the Surface ann nnannnnanennanenn 22 Step 4 Connect the Cable S ccccssceceseeceseeceneeceneeeeneeceneeseneeseneees 23 Step 5 Access the Camera Live VieW ccssseesssseesssseeeeeseeeenseseenees 23 Step 6 Adjust the Viewing Angle and Focus naaar 24 Step 7 Close the Dome Cover nnnanann nennen menens nennen nennennnnnen 25 2 www acti com gt 3 ACT Hardware Manual Other Adjustments and Accessories 27
5. A1D 500 V6 04 15 AC Megapixel IP Dome 228 5 6 1 172 16 26 82 E93 A XX 13L 00116 00 0F 7C 0C 90 57 A1D 500 V6 04 15 AC Megapixel IP Dome 228 5 6 1 172 16 26 95 E93 A XX 13L 00141 00 0F 7C 0C 90 70 A1D 500 V6 04 15 AC Megapixel IP Dome 228 5 6 1 172 16 26 85 E93 A XX 13L 00152 00 0F 7C 0C 90 7B A1D 500 V6 04 15 AC Megapixel IP Dome 228 5 6 1 172 16 26 163 172 16 26 111 172 16 26 161 E97 A XX 13K 00147 B52 A XX 13L 00009 B amp 5 A XX 13L 00007 00 0F 7C 0C 60 9A 00 0F 7C 0C 8E 98 00 0F 7C 0C 8F 0E A1D 500 V6 05 16 AC A1D 500 V6 05 22 AC A1D 500 V6 05 23 AC Megapixel IP Dome Megapixel IP Dome Megapixel IP Dome 228 5 6 1 172 16 26 42 E94 A XX 13 00054 00 0F 7C 0B AE 80 A1D 500 V6 06 02 AC Megapixel IP Dome 172 16 26 238 I94 A XX 13J 00014 00 0F 7C 0B F8 CE A1D 500 V6 05 21 AC Megapixel IP PTZ Camera JOO OWOO OOO OOOO OO 0 D0 DOBLE gt 172 16 26 7 I92 A XX 13J 00007 00 0F 7C 0B F8 95 A1D 500 V6 05 22 AC en lt s n in nn an mn a amns ns Anann an aman an n an Add s sm PAA sen am nn san Remove You can quickly notice the camera model in the list Click on the IP address to automatically launch the default browser of the PC with the IP address of the target camera filled in the address bar of the browser already 32 www acti com
6. Adjustment Screw Screw Adjustment Procedures 1 Loosen the tilt adjustment screws adjust the tilt and then tighten back the screws to fix the tilt position 2 Turn the rotation adjustment to rotate the viewing orientation 3 Loosen the pan adjustment screw move the pan direction and then tighten back the screw to fix the pan position 24 ACTI Connecting Vision vA Hardware Manual Step 7 Close the Dome Cover 1 Align the screws with the screw holes of the camera Note that if the cables are routed along the ceiling or wall route the cable to pass through the cable hole on the dome cover 2 Tighten the three 3 screws to attach the dome cover to the camera body 3 Remove the plastic covering the dome cover 25 ACTI Connecting Vision vA Hardware Manual Final installation should look similar to the illustration below 20 ACTI Connecting Vision vA Hardware Manual Other Adjustments and Accessories How to Replace the Dome Cover For more discrete surveillance needs the bundled dome cover can be replaced with a smoke vandal proof cover available for purchase To replace the dome cover do the following 1 Loosen the three 3 screws to open the dome cover 2 Remove the three 3 screws to detach the bracket 3 Remove the bracket and dome cover from the cover housing
7. Ml X Favorites Name Category ao ME Desktop J ACD2100 10A X 00450 Other Devices Jp Downloads J ACM3701 10H X 00473 Other Devices Recent Places ACM5801 10A X 00008 Other Devices 1 ANNA LAPYKO Other Devices Documents l E271 A 01 00A 0826 Other Devices a Music E43 A XX 12L 00050 Other Devices fe Pictures E43 A XX 12L 00107 Other Devices E Videos E63 A XX 13C 00071 Other Devices E73 A XX 13D 00337 Other Devices B Computer E93 A XX 13L 00116 Other Devices J ENR 130 ENR Other Devices Ga Network l ENR 130 ENR Other Devices 4 TT o E63 A XX 13C 00071 Categories Other Devices LID Network location ACTi com 3 Hardware Manual ACTI Connecting Vision vA Double click on the camera model name the default browser of the PC is automatically launched and the IP address of the target camera is already filled in the address bar of the browser lf you work with our cameras regularly then there is even a better way to discover the cameras in the network by using IP Utility The IP Utility is a light software tool that can not only discover the cameras but also list lots of valuable information such as IP and MAC addresses serial numbers firmware versions etc and allows quick configuration of multiple devices at the same time The IP Utility can be downloaded for free from http www acti com IP_Utility With just one click you can launch the IP Utility and there w
8. the reset button 1 The administrator s password has been forgotten and therefore the camera cannot be accessed 2 Incase of IP address mask or allow deny filter related issues resulting with inability to modify these settings 3 Incase of connectivity issues or abnormal video quality How to do the reset properly Press and hold the reset button for 5 seconds 9 www acti com Bq ACTi Connecting Vision Hardware Manual 4 Digital Input Output DI DO and Audio Input Output This connector connects to digital input or output devices such as an alarm trigger panic button etc as well as audio input and output devices such as microphones and speakers Digital Input DI and Digital Output DO devices are used in applications like motion detection event triggering alarm notifications etc See Prepare the DI DO and Audio Input Output Connector Optional on page 16 for more information 5 DC 12V Power Input In case the camera is connected to a non PoE Power over Ethernet switch use this connector to connect the camera to an external power adapter not included See Prepare the Power Adapter Optional on page 14 for more information 10 ACTI Connecting Vision vA Hardware Manual Mounting Options There are several mounting options that you can use to install the camera Select the most Suitable solution for your installation environment Mount Types Accessories Surfa
9. the wire mAN tan et For Audio Use 1234 To connect digital input output devices DI DO map the pins to one of the pin combinations below Mapping Instructions Connect the wires of the output device to DIO PW Digital Output DO Pin 1 and DO Pin 3 Digital Input ry DIO GND Connect the wires of the input device to DIO GND DI a ld Pin 2 and DI Pin 4 jo pd ACTI Connecting Vision Hardware Manual The table below shows the DI DO connection specifications Device Connection Connection design TTL compatible logic levels To trigger low Logic level 0 OV 0 4V Voltage Normal high Logic level 1 3 1V 30V Connection design Transistor Open Collector Voltage amp Current lt 24V DC lt 50mA Typical Connection Based on these specifications if the DI device has a voltage of OV 30V or the DO device has a voltage of lt 24V lt 50mA then the camera can supply internal power to these devices and there is no need to connect the DI DO device to an external power source In this case wire connection to Pins 1 to 4 Use the DIO GND and DI pins to connect a DI device and use the DIO PW and DO pins to connect a DO device See wiring scheme below NORMAL 3 1V NORMAL gt HIGH TRIGGER LOW BATTERY 7 D4 ACTi Connecting Vision Hardware Manual High Voltage DO Device Connection Even though the camera provides 12V power
10. this may not be enough for some high voltage DO devices such as a Ceiling light or a motor that opens or closes a gate In this case there is a need to connect an external relay See wiring scheme below NORMAL HIGH TRIGGER LOW 4 x AC110v Wi N MOTOR Note that when choosing an appropriate relay please refer to its specifications and make sure they match the above design The triggering circuit voltage has to be around 12V DC and the switch controlled circuit voltage has to match the external power supply e g 110V AC or 220V AC The illustration below is a graphic example of connecting a relay to a high voltage DO device s s eert la se 110V 220V AC External Power Source Relay DO1 Device Camera Illuminator NOTE For more information on DI DO connections please refer to the Knowledge Base article All about Digital Input and Digital Output downloadable from the link below http www acti com kb detail asp KB _ID KB2009123000T7 s ACTI Connecting Vision da Hardware Manual How to Connect Audio Devices Audio input output devices such as an active microphone or speaker can be connected to the camera using the supplied terminal block Press and hold the orange tab as you insert the wire through the pin slot then release the orange tab to secure the wire For DI DO Use To connect audio devices map the pins to
11. 2 16 26 11 00 4 KCM3911 228 5 6 1 172 16 26 13 00 KCM5111 228 5 6 1 172 16 26 40 00 KCM5211 228 5 6 1 172 16 26 41 00 i KCM5311 228 5 6 1 172 16 26 50 00 3 z z KCM5111 228 5 6 1 172 16 26 52 00 ee _KcM5311 228 5 6 1 172 16 26 53 00 J TCM5311 228 5 6 1 172 16 26 54 00 TCM5611 228 5 6 1 172 16 26 55 00 En EN TCM5111 228 5 6 1 172 16 26 57 D 310 V4 12 09 TCD2100 228 5 6 1 172 16 26 61 TCM1231 228 5 6 1 Sess With the procedure shown above all the cameras will have unique IP addresses starting from 192 168 0 101 In case there are 20 cameras selected the last one of the cameras would have the IP 192 168 0 120 Later by pressing the Refresh button of the IP Utility you will be able to see the list of cameras with their new IP addresses Please note that it is also possible to change the IP addresses manually by using the Web browser In such case please plug in only one camera at a time and change its IP address by using the Web browser before plugging in the next one This way the Web browser will not be confused about two devices having the same IP address at the same time 34 pd ACTI Connecting Vision Hardware Manual Access the Camera Now that the camera and the PC are both having their unique IP addresses and are under the same network segment it is possible to use
12. How to Replace the Dome Cover nnaannnnne annen nanennnanenenanenen 27 USING a M mory Card assisia aa a 30 How to Insert the Memory Card aanne eneen en enen en ennn enen 30 How to Remove the Memory Card aanne eneen eneen enen 30 Accessing the Camera ane aanennnen 31 Configure the IP Addresses nnnennennenane nennen nennen nennen nnenrnnenn 31 ACCESS Ne Camerana seenneenneedenndennsknadentdennsenedeeaeendennseskeeendeen 35 3 www acti com Dd ACTi Connecting Vision Hardware Manual Precautions Read these instructions You should read all the safety and operating instructions before using this product Heed all warnings You must adhere to all the warnings on the product and in the instruction manual Failure to follow the safety instruction given may directly endanger people cause damage to the system or to other equipment Servicing Do not attempt to service this video device yourself as opening or removing covers may expose you to dangerous voltage or other hazards Refer all servicing to qualified service personnel Trademarks All names used in this manual are probably registered trademarks of respective companies Liability Every reasonable care has been taken during the writing of this manual Please inform your local office if you find any inaccuracies or omissions We cannot be held responsible for any typographical or technical errors and reserve the right to mak
13. PC both the camera and the PC have to be within the same network segment In most cases it means that they both should have very similar IP addresses where only the last number of the IP address is different from each other There are 2 different approaches to IP Address management in Local Area Networks by DHCP Server or Manually Using DHCP server to assign IP addresses If you have connected the computer and the camera into the network that has a DHCP server running then you do not need to configure the IP addresses at all both the camera and the PC would request a unique IP address from DHCP server automatically In such case the camera will immediately be ready for the access from the PC The user however might not know the IP address of the camera yet It is necessary to know the IP address of the camera in other to be able to access it by using a Web browser The quickest way to discover the cameras in the network is to use the simplest network search built in the Windows system just by pressing the Network icon all the cameras of the local area network will be discovered by Windows thanks to the UPnP function support of our Cameras In the example below we successfully found the camera model that had just connected to the network t b Network gt Search Network Organize v Search Active Directory Network and Sharing Center Add a printer Add a wireless device hem
14. ables will pass through the surface drill the cable hole and the three 3 screw holes on the surface Mounting Hole F FA i 6 i 3 N A Mounting Hole f Cable hole B507 00036 000 e Ifthe cables will be routed along the surface just drill the three 3 screw holes on the surface 3 Insert the plastic plugs into the screw holes 20 ACTI Connecting Vision da Hardware Manual Step 2 Open the Dome Cover NOTE To avoid scratches or leaving fingerprints on the dome cover it is recommended to retain the plastic covering the dome cover until the camera is completely installed 1 With the bundled hex screwdriver loosen the three 3 screws securing the dome cover 2 Liftto remove the dome cover 3 If the cables will be routed along the ceiling or wall remove the cable tab from the dome cover 4 Ifthe cables will pass through the ceiling or wall route and pull the cables through the hole on the surface 2 ACTI Connecting Vision dol Hardware Manual Step 3 Install the Camera to the Surface 1 If necessary insert a memory card with the metallic contacts facing down into the card slot of the camera 2 Align the camera screw holes and the cable hole if necessary to the holes on the surface and attach the three 3 supplied screws to secure the camera A CAUTION When using electric sc
15. amage and will often require extensive work by a qualified technician to restore the video product to its normal operation Safety Check Upon completion of any service or repairs to this video product ask the service technician to perform safety checks to determine if the video product is in proper operating condition 6 www acti com Hardware Manual Introduction The List of Models This hardware manual contains the following models Bq ACTi Connecting Vision SMP Indoor Dome with D N Adaptive IR Basic WDR Fixed lens www acti com ACTI Connecting Vision vA Hardware Manual Package Contents Camera Mounting Screw Kit Hexagon Screwdriver Terminal Block Terminal Block Drill Template for Power for Audio and DI DO Drill Template Quick Installation Guide Warranty Card Hardware Warranty Policy pa acti eed EN B en as 8 www acti com ACTI Connecting Vision vA Hardware Manual Physical Description 1 Ethernet Port Connects to a network using an Ethernet cable 2 Memory Card Slot Insert a memory card not included into this slot for local recording purposes See Using a Memory Card on page 30 for more information NOTE Supports microSDHC and microSDXC cards 3 Reset Button The purpose of reset button is to restore the factory default settings of the camera including the administrator s password When to use
16. at the camera s IP address is 192 168 0 100 you can access it by opening the Web browser and typing the following address into Web browser s address bar http 192 168 0 100 Upon successful connection to the camera the user interface called Web Configurator would appear together with the login page The HTTP port number was not added behind the IP address since the default HTTP port of the camera is 80 which can be omitted from the address for convenience Web Configurator x Web Configurator Account Password Language English v Login Reset Before logging in you need to know the factory default Account and Password of the camera Account Admin Password 123456 For further operations please refer to the Firmware User Manual 6
17. ce Suitable when mounting the camera directly on walls or ceilings Mount without extra accessories See nstalling the Camera on a Surface on page 20 for mounting instructions Flush Mount Suitable when mounting the camera discretely above dropped ceilings wherein only the dome cover will be visible underneath the ceiling PMAX 1003 Gang Box Suitable for locations which require the use of gang boxes The Converter Gang Box Converter can be attached to a two gang or 4 Square gang box Then the camera can be installed on the Gang Box Converter All cables are hidden inside the gang box PMAX 0803 Pendant Suitable when mounting the camera on hard and high ceilings Mount PMAX 0101 PMAX 0103 Straight Tube with Bracket PMAX 0102 Straight Tube I ACTI Connecting Vision vA Hardware Manual Mount Types Accessories straight Wall Suitable when mounting the camera on straight walls Mount PMAX 0308 L Type Wall Mount PMAX 0101 PMAX 0305 Heavy Duty Wall Mount e Db 7 Vertical Pole Suitable when mounting the camera on vertical poles M ori PMAX 0101 PMAX 0305 PMAX 0503 EEE I Horizontal Pole Mount PMAX 0101 PMAX 0102 Corner Suitable when mounting the camera on a corner wall Mount PMAX 0101 PMAX 0305 PMAX 0402 12 ACTI Connecting Vision vA Hardware Manual Other Mounting Accessories Accessories PMAX 0104 Extension Tube e For more in
18. e changes to the product and manuals without prior notice 4 www acti com Bd ACTi Connecting Vision Hardware Manual Federal Communications Commission Statement This equipment has been tested and found to comply with the limits for a class B C digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help Warning Changes or modifications to the equipment that are not expressly approved by the responsible party for compliance could void the user s authority to operate the equipment European Community Compliance State
19. formation about the mounting solutions and accessories please check the Mounting Accessory Selector in our website http www acti com mountingselector e The above mounting accessories are not included in the package Contact your sales agents to purchase 9 Dd ACTi Connecting Vision Hardware Manual Before Installation This section describes the procedures in preparing the external devices that you can connect to the camera The camera supports DC12V power input Digital Input and Output DI DO and Audio Input and Output devices using the bundled terminal blocks The use of these devices however is optional Prepare the Power Adapter Optional In case of using a non PoE switch or your PoE switch has limited power supply you can purchase a power adapter and directly connect the camera to a power outlet The power adapter must be connected to the supplied terminal block before use To do this follow the procedures below 1 Loosen the screws of the 12V and GND pins of the power terminal block 2 Take note that a standard power adapter cable has two 2 different wires Connects to GND Pin White stripe Connects to 12V Pin 14 ACTI Connecting Vision vA Hardware Manual 3 Connect the wire with the white stripe to the 12V pin and the other to the GND pin 4 Tighten the screws of the 12V pin and the GND pins to secure the wire connection
20. ill be an instant report as follows az Refresh Device Settings IP Address NetMask 172 16 26 79 255 255 255 0 Change Network Address sco raver IP Address 172 16 26 67 Serial No DS1 A XX 12K 00480 MAC Address 00 0F 7C 09 81 9A Firmware Upgrade FW Version A1D 500 V6 04 15 AC Basic Search Config Backup Model Megapixel IP Dome Config Restore Reset Save amp Re Multicast IP 228 5 6 1 172 16 26 140 D54 A XX 134 00165 00 0F 7C 09 D6 BD A1D 500 V6 04 15 AC Megapixel IP Dome 228 5 6 1 172 16 26 72 E91 A XX 13B 00154 00 0F 7C 0A 3E B9 A1D 500 V6 04 15 AC Megapixel IP Dome 228 5 6 1 172 16 26 108 E63 A XX 13C 00071 00 0F 7C 0A 58 3D A1D 500 V6 04 15 AC Megapixel IP Dome 228 5 6 1 172 16 26 12 DSS A XX 13C 00107 00 0F 7C 0A 8A B5 A1D 500 V6 04 15 AC Megapixel IP Dome 228 5 6 1 172 16 26 18 E73 A XX 13D 00337 00 0F 7C 0A 98 90 A1D 500 V6 04 15 AC Megapixel IP Dome 228 5 6 1 172 16 26 2 E72 A XX 13D 00166 00 0F 7C 0A A3 3A A1D 500 V6 04 15 AC Megapixel IP Dome 228 5 6 1 172 16 26 167 E9S5 A XX 131 00117 00 0F 7C 0B AF 55 A1D 500 V6 04 15 AC Megapixel IP Dome 228 5 6 1 172 16 26 69 E93 A XX 13L 00079 00 0F 7C 0C 90 32 A1D 500 V6 04 15 AC Megapixel IP Dome 228 5 6 1 172 16 26 86 E93 A XX 13L 00107 00 0F 7C 0C 90 4E
21. ment C 4 This product has been tested and found to comply with the limits for Class B Information Technology Equipment according to European Standard EN 55022 and EN 55024 In a domestic environment this product may cause radio interference in which cause the user may be required to take adequate measures 5 www acti com gt ACTi Connecting Vision Hardware Manual Safety Instructions Cleaning Disconnect this video product from the power supply before cleaning Attachments Do not use attachments not recommended by the video product manufacturer as they may cause hazards Do not use accessories not recommended by the manufacturer Only install this device in a dry place protected from weather Servicing Do not attempt to service this video product yourself Refer all servicing to qualified service personnel Damage Requiring service Disconnect this video product from the power supply immediately and refer servicing to qualified service personnel under the following conditions 1 When the power supply cord or plug is damaged If liquid has been spilled or objects have fallen into the video product 3 Ifthe inner parts of video product have been directly exposed to rain or water Ifthe video product does not operate normally by following the operating Instructions in this manual Adjust only those controls that are covered by the instruction manual as an improper adjustment of other controls may result in d
22. ng settings a Set up a new connection or network x Delete Set up a wireless broadband dial up ad hoc or VPN connection or set up a router or a Rename access point Properties Py Connect to a network ae Connect or reconnect to a wireless wired dial up or VPN network connection ee also HomeGroup Choose homegroup and sharing options Internet Options Access files and printers located on other network computers or change sharing Windows Firewall POE btocol Version 4 TCP IPv4 Properties LO jm bled ee ee Connect using amp Intel R 82567LM 3 Gigabit Network Connection You can get IP settings assigned automatically if your network supports this capability Otherwise you need to ask your network administrator for the appropriate IP settings Obtain an IP address automatically This connection uses the following items a Use the following IP address o Client for Microsoft Networks Sl VirtualBox Bridged Networking Driver laos Packet Scheduler File and Printer Sharing for Microsoft Networks Intemet Protocol Version 6 TCP IPv6 IP address 192 168 0 99 Subnet mask Pt a ae LG 0 Default gateway intemet Protocol Version 4 TCP Pv4 Link Layer Topology Discovery Mapper 1 0 Driver Link Layer Topology Discovery Responder Obtain DNS server address automatically IEEE ES ER Use the following DNS server addresses Descrip
23. one of the pin combinations below Device Pin oo Mapping Instructions Audio Output AO GND Connect the wires of the audio output device to AO A our AO_GND Pin 1 and A_OUT Pin 2 Audio Input Al_ GND Connect the wires of the audio input device to A1 Al_GND Pin 3 and A_IN Pin 4 NOTE For more information about AUDIO in connections please refer to the Knowledge Base article How to Use Audio in of ACTi Cameras downloadable from the link below http www acti com support KnowledgeBase outside detail asp KB ID KB20100114003 9 Bq ACTi Connecting Vision Hardware Manual Installing the Camera on a Surface This section describes the procedures in installing the camera on a flat surface such as a hard or dropped ceiling and straight or tilted walls Before installation make sure the wall or the ceiling can bear more than the weight of the camera Step 1 Drill the Holes Before drilling the holes on the ceiling or wall note the direction of the connectors side of the camera which is also the opposite side of the camera logo This influences the camera placement and where you should drill the hole where the cables will pass through or how the cables will go along the ceiling or wall 1 Use the supplied drill template to mark the screw holes on the surface according to the preferred orientation 2 Determine how the cables will be routed pass through the surface or along the surface e Ifthe c
24. rewdrivers be careful not to touch the camera components while attaching the screws Since electric screwdrivers vary in sizes speed and force they may bruise and damage the camera components DISCLAIMER ACTi will not be responsible for camera damage caused by improper installations or the misuse of equipment for installation 22 bia ACT Hardware Manual Step 4 Connect the Cable s 1 Connect the network cable to the Ethernet port of the camera If necessary connect other cable connectors optional like audio input output DI DO and DC 12V power to the corresponding connectors on the camera Digital Input Output DI DO and Audio Input Output Ethernet Port Connector 12V Power Connector 2 Connect the other end of the network cable to a switch or injector Then connect the switch or injector to a network PC and a power source See Power over Ethernet PoE connection example below Ethernet Cable Ethernet Cable Data PoE Injector Power Cable PoE Switch Ethernet Cable Data Power AC Power Source Camera Step 5 Access the Camera Live View See Accessing the Camera on page 31 for more information on how to access the Live View of the camera 2 ACTI Connecting Vision da Hardware Manual Step 6 Adjust the Viewing Angle and Focus Camera Parts Overview uz ent Screw Pan Adjustm Tilt Adjustment Tilt
25. the Web browser of the PC to access the camera You can use any of the browsers to access the camera however the full functionality is provided only for Microsoft Internet Explorer The browser functionality comparison Functionality Internet Explorer Other browsers E PTZ Conto Capture the snapshot Video overlay based configuration Motion Yes No Detection regions Privacy Mask regions QuickTime http www apple com quicktime download has to be installed in PC first before using any non Internet Explorer browsers to be able to get live video feed from the camera with those browsers It is a free and open source cross platform multimedia player Disclaimer Notice The camera manufacturer does not guarantee the compatibility of its cameras with QuickTime since it is a third party software the third party has the right to modify their utility any time which might affect the compatibility In such cases please use Internet Explorer browser instead When using Internet Explorer browser the ActiveX control for video stream management will be downloaded from the camera directly the user just has to accept the use of such control when prompted so No other third party utilities are required to be installed in such case The examples in this manual are based on Internet Explorer browser in order to cover all functions of the camera 5 Bq ACTi Connecting Vision Hardware Manual Assuming th
26. tion Transmission Control Protocol Intemet Protocol The default wide area network protocol that provides communication across diverse interconnected networks Preferred DNS server Alternate DNS server en F Validate settings upon exit s OK Cancel ACTI Connecting Vision vA Hardware Manual Manually adjust the IP addresses of multiple cameras If there are more than 1 camera to be used in the same local area network and there is no DHCP server to assign unique IP addresses to each of them all of the cameras would then have the initial IP address of 192 168 0 100 which is not a proper situation for network devices all the IP addresses have to be different from each other The easiest way to assign cameras the IP addresses is by using IP Utility IP_Utility IP Address NetMask 172 16 26 192 255 255 255 0 Basic Search T O Refresh Device Settings Change Network Address Firmware Upgrade Config Backup Config Restore Save amp Reboot a a Total 56 Account Password 123456 Http Port w IP Address MAC Address FW Version Model Serial No Multicast IP Status 172 16 26 2 00 0F 7C 07 DE 65 A1D 311 V5 07 05 AC Hemispheric Camera KCM3911 228 5 6 1 172 16 26 4 00 0F 7C 08 17 C2 A1D 310 V4 12 02 AC Mega IP Camera TCM1111 228 5 6 1 172 16 26 6 00 E aAA Fa KCM7311 228 5 6 1 172 16 26 7 00 TCM6630 228 5 6 1 172 16 26 10 00 Dynamic IP Address TCM4201 228 5 6 1 17
Download Pdf Manuals
Related Search