Home

Barco Nio Color 3MP LED

1. 2 Navigate to the Configuration gt Calibration gt Embedded QA menu 3 Select DICOM compliance check to start the compliance check Warning Pressing a key during the compliance check will abort the check K5902067 NIO 3MP LED DISPLAY 26 11 2014 5 Advanced operation 5 15 4 DICOM calibration About DICOM calibration The DICOM calibration will add a correction to the current DICOM curve to approach the perfect DICOM curve as good as possible To start DICOM calibration 1 Bring up the OSD main menu 2 Navigate to the Configuration gt Calibration gt Embedded QA menu 3 Select DICOM calibration to start the calibration Warning Pressing a key during calibration will abort the calibration previous values will be restored Note After calibration the compliance check will start automatically 5 15 5 Reset DICOM calibration About reset DICOM calibration It is possible to restore the original not corrected DICOM curve To reset the DICOM calibration 1 Bring up the OSD main menu 2 Navigate to the Configuration gt Calibration gt Embedded QA menu 3 Enter the DICOM preferences submenu 4 Select reset DICOM calibration to restore the original not corrected DICOM curve 5 15 6 DICOM error threshold About DICOM error threshold The threshold to define the DICOM compliance can be modified in steps of 5 starting from 5 to 30 When the maximum deviation is not bigger than the selected threshold the com
2. e an AC power cord e an external power supply If you ordered a Barco display controller it s also in the box together with its accessories A dedicated user guide is available on the system CD x Keep your original packaging It is designed for this display and is the ideal protection during transport and storage A K5902067 NIO 3MP LED DISPLAY 26 11 2014 2 Parts controls and connectors 2 PARTS CONTROLS AND CONNECTORS 2 1 Display front view Overview a Image 2 1 Front view a Left key o Standby key 2 Right key Power LEDs Menu key Bottom downstream USB The key icons are displayed above the keys adapted to the function that it is used for menu dependent See Navigating through the OSD menus page 17 K5902067 NIO 3MP LED DISPLAY 26 11 2014 AAA 2 Parts controls and connectors 2 2 Display rear view Connector compartment cover closed Q DKO 000 0 0 00 9 D 0 0 00 0 000 00000600 00 O 00 00 0 00 0 o 0 0 00 0 000 02t 0t o O o 0 0 0 0 0 0 6 0 5 fi o O Oe SON o OM 000009 O SSA ES es a BARCO Image 2 2 Rear view with closed connector compartment cover Connector compartment cover Foot lock clip Tilt amp swivel foot O Cable duct K5902067 NIO 3MP LED DISPLAY 26 11 2014 2 Parts controls and connectors Connector compartm
3. 26 11 2014 SeSsSSsSsSsSssse 21 5 Advanced operation 5 9 Hibernate About hibernate Enabling hibernation will not only switch off the backlight but will also force the display to disable other functionalities so that power consumption is further reduced to a minimum This happens after a specific period of time which can be manually adjusted x Hibernate can only be enabled on your display when the DPMS mode is enabled first Therefore please refer to DPMS mode page 21 to do this To enable disable hibernation on your display 1 Bring up the OSD main menu 2 Navigate to the Configuration gt Power Management menu 3 Enter the Hibernate submenu 4 Select Enabled Disabled as desired and confirm To specify the hibernate timeout 1 Bring up the OSD main menu 2 Navigate to the Configuration gt Power Management menu 3 Enter the Hibernate Timeout submenu 4 Set the timeout value as desired and confirm 5 10 Luminance target About the luminance target The luminance target of your Nio 3MP LED Display is adjustable over a predefined range When you change the luminance target the display will adjust its backlight to reach the target To set the luminance target 1 Bring up the OSD main menu 2 Navigate to the Configuration gt Calibration menu 3 Enter the Luminance Target submenu 4 Set a luminance target value as desired and confirm The default factory DICOM calibrated luminance value i
4. 26 11 2014 A Table of contents 6 2 IRE DACKING VOUN GISDIAY sas oes vote eae eed te Gene dale SA 35 Cleaning your display atar aida io 37 Tal GCICAMMOG IMSIUCIONS a een 0 od A does 37 Important Informations A 39 O Sately INO Malo ita sita 39 8 2 Environmental information issues 40 8 3 Regulatory compliance information eee eee nr 43 O24 EMC NOICE corsa trend das 43 6 9 EXpPlanatlo OF SYMNDOIS san tran 47 0 0 LegalrtiscialMer cities bit ada skoda ui td ars 49 Sf Technical SDECMICAIONSEL nn e nn tt dados ace 50 8 8 Open source license information 0 ccc cece cece n K K n nk 51 K5902067 NIO 3MP LED DISPLAY 26 11 2014 1 Welcome 1 WELCOME 1 1 About the product Overview Thank you for choosing this Nio 3MP LED Display Nio 3MP LED Display is an industry standard 3MP color display system with LED backlights for depend able diagnostic viewing in high bright color Nio 3MP LED Display provides an effective display solution for a multitude of applications and modalities including 3D PACS 3D echo ultrasound orthopedic imaging CAD image fusion nuclear medicine and PET Confident color reading Equipped with high bright LED backlights Nio 3MP LED Display delivers excellent brightness and more shades of gray to detect subtle details more quickly The unique front sensor ensures you see consistent and precise images at all times for co
5. Barco recommends keeping color matched displays together Furthermore it is impor tant to use all displays of a multi head configuration at the same rate to preserve color matching throughout the economic lifetime of the system K5902067 NIO 3MP LED DISPLAY 26 11 2014 _W eeSSsSsSssssse 15 4 Daily operation Maximize quality assurance The MediCal QAWeb system offers online service for high grade Quality Assurance providing maximum diagnostic confidence and uptime Barco recommends to install MediCal QAWeb Agent and apply the default QAWeb policy at least This policy includes calibration on regular intervals Connecting to MediCal QAWeb Server offers even more possibilities Learn more and sign up for the free MediCal QAWeb Essential level at www barco com healthcare ga 4 2 Key indicator lights About the key indicator lights By default the indicator lights of the keys will be dimmed which makes the keys unavailable at that mo ment To make the keys illuminate and available for further actions touch one of the keys As a result all keys will be illuminated and are now available for further actions However if no further actions are taken within the following 5 seconds the keys will dim again The key auto dim function can be disabled in the OSD menus Please refer to Key in dicator lights page 20 for detailed instructions on how to do this 4 3 Standby switching About standby switching The conne
6. Function submenu 4 Select one of the available display functions and confirm 5 13 Ambient Light Compensation ALC About ALC COM display function is selected Therefore please refer to Display functions page Ambient Light Compensation ALC can only be enabled on your display when the DI 23 to correctly set the display function When ALC is enabled the DICOM display function will be recalculated taking a preset ambient light cor rection value into account This value is determined by the selected reading room Therefore it is also important to select a realistic reading room when enabling ALC This can be done by following the instruc tions in Reading rooms page 24 To enable disable ALC 1 Bring up the OSD main menu 2 Navigate to the Configuration gt Calibration gt Ambient Light menu 3 Enter the Ambient Light Compensation submenu 4 Select Enabled Disabled as desired and confirm 9 14 Reading rooms 24 About reading rooms x Reading rooms can only be selected when the DICOM display function is selected Therefore please refer to Display functions page 23 to correctly set the display function The American Association of Physicists in Medicine AAPM composed a list of pre defined reading rooms Each of these reading rooms are defined by following parameters e the maximum light allowed in this type of room e the preset ambient light correction value for this reading room These p
7. any external devices connected to it key board mouse Please note that a connection from a PC USB downstream connector to the display s USB upstream connector is required to be able to use this functionality By enabling the Ethernet over USB you allow the internal Nio 3MP LED Display processor to communicate directly over USB with the connected PC x Enabling the Ethernet over USB is only recommended when you are using a non Barco display controller If you are using a Barco display controller this communication will automatically be done over the connected video cable s To enable disable the eth over USB 1 Bring up the OSD main menu 2 Navigate to the Configuration gt Connectivity menu 3 Enter the Eth over USB submenu 4 Select Enabled Disabled as desired and confirm n K5902067 NIO 3MP LED DISPLAY 26 11 2014 5 Advanced operation 5 7 USB About USB By default USB will be enabled This will allow the connected PC to communicate directly over USB with the internal Nio 3MP LED Display processor By disabling USB communication between the internal Nio 3MP LED Display processor and the con nected PC will not be possible This does not disable the USB hub and still allows to make use of the display s USB downstream connectors and any external devices connected to it keyboard mouse Please note that a connection from a PC USB downstream connector to the display s USB upstream connector is re
8. certain grayscale color parts contain more diagnostic information then others To respond to these conclusions display functions have been defined These functions emphasize on these parts containing crucial diag nostic information by correcting the native panel behavior If you select Native the native panel behavior will not be corrected Dynamic Gamma 1 8 These are gamma functions that are shifted to take into account the non zero luminance of an LCD panel when driven with a black signal They are especially useful in CT applications to improve the perception of low Hounsfield values DICOM Digital Imaging and Communications Dynamic Gamma 2 2 in Medicine is an international standard that was developed to improve the quality and communication of digital images in radiology In short the DICOM display function results in more visible grayscales in the images Barco recommends selecting the DICOM display function for most medical viewing applications K5902067 NIO 3MP LED DISPLAY 26 11 2014 23 5 Advanced operation User This display function will be automatically selected when display functions are defined by MediCal QAWeb Gamma 1 8 Select one of these display functions in case the Gamma 2 2 display is to replace a CRT display with a gamma of 1 8 or 2 2 respectively To select a display function 1 Bring up the OSD main menu 2 Navigate to the Configuration gt Calibration menu 3 Enter the Display
9. under the European Directive 2012 19 EU governing waste from electrical and electronic equipment this product must not be disposed of with other municipal waste Please dispose of your waste equipment by handing it over to a designated collection point for the K5902067 NIO 3MP LED DISPLAY 26 11 2014 8 Important information recycling of waste electrical and electronic equipment To prevent possible harm to the environment or human health from uncontrolled waste disposal please separate these items from other types of waste and recycle them responsibly to promote the sustainable reuse of material resources For more information about recycling of this product please contact your local city office or your municipal waste disposal service For details please visit the Barco website at http www barco com en AboutBarco weee Turkey RoHS compliance X m rkiye Cumhuriyeti AEEE Y netmeli ine Uygundur Republic of Turkey In conformity with the WEEE Regulation A EA ki RoHS Chinese Mainland RoHS R Ha PEA h EF AT m5 RE l E K HA REX RoHS LAR ab Y Barco a HARER SARA EURA MN Eo HEA RHS HE S a A E SH RP L PMCV T A CEE B mPa ARREZ R H According to the China Administration on Control of Pollution Caused by Electronic Information Products Also called RoHS of Chinese Mainland the table below lists the names and contents of toxic and or hazardous substances that Barco s product may contain The RoHS of Chinese Mai
10. 067 NIO 3MP LED DISPLAY 26 11 2014 3 6 Repackaging instructions 36 K5902067 NIO 3MP LED DISPLAY 26 11 2014 7 Cleaning your display 7 CLEANING YOUR DISPLAY 7 1 Cleaning instructions To clean the display Clean the display using a sponge cleaning cloth or soft tissue lightly moistened with a recognized clean ing product for medical equipment Read and follow all label instructions on the cleaning product In case of doubt about a certain cleaning product use plain water Do not use following products Alcohol solvents at higher concentration gt 5 Strong alkalis lye strong solvents Acid Detergents with fluoride Detergents with ammonia Detergents with abrasives Steel wool Sponge with abrasives Steel blades Cloth with steel thread CAUTION Take care not to damage or scratch the front glass or LCD Be careful with YN rings or other jewelry and do not apply excessive pressure on the front glass or LCD CAUTION Do not apply or spray liquid directly to the display as excess liquid may cause YN damage to internal electronics Instead apply the liquid to a cleaning cloth K5902067 NIO 3MP LED DISPLAY 26 11 2014 37 7 Cleaning your display 38 K5902067 NIO 3MP LED DISPLAY 26 11 2014 8 Important information 8 IMPORTANT INFORMATION 8 1 Safety information General recommendations Read the safety and operating instructions before operating the device Retain safety and opera
11. 5 C to 30 C within specs Storage temperature 20 C1 00C Operating humidity 8 80 non condensing Seema ee 95 non condensing Z gt Z C gt U S o O Q S D dl years op Operation altitude 000 m Storage altitude 7500 m 8 8 Open source license information Open source license information Open source license usage This product contains software components released under an Open Source license A copy of the source code is available on request by contacting your Barco customer support representative EACH SEPARATE OPEN SOURCE SOFTWARE COMPONENT AND ANY RELATED DOCUMENTA TION ARE PROVIDED AS IS WITHOUT EXPRESS OR IMPLIED WARRANTY INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICU LAR PURPOSE IN NO EVENT SHALL THE COPYRIGHTHOLDER OR ANY OTHER CONTRIBUTOR K5902067 NIO 3MP LED DISPLAY 26 11 2074 5 8 Important information 92 BE LIABLE FOR DIRECT INCIDENTAL OR CONSEQUENTIAL DAMAGES EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES MORE INFORMATION DETAILS IS TO BE FOUND IN EACH SPE CIFIC OPEN SOURCE LICENSE Copyright on each Open Source Software component belongs to the respective initial copyright holder each additional contributor and or their respective assignee s as may be identified in the respective doc umentation source code README file or otherwise You shall not remove or obscure or otherwise alter the respecti
12. D Bottom box Box Power supply cables Bottom buffer Top buffer K5902067 NIO 3MP LED DISPLAY 26 11 2014 33 6 Repackaging instructions 6 1 Protection buffer Top box o Display Display controller box Replacing the protection buffer 34 How to replace the protection buffer 1 Place the display on a stable surface 2 Put the display in the lowest position and fasten the height mechanism see Unlocking the height mech anism page 9 3 Very important Tilt the panel away from the foot before changing the orientation 4 Turn the panel counterclockwise to put the panel in landscape orientation see Adjusting the display position page 9 5 Place the connector compartment cover in the protection buffer 6 Slide the protection buffer over the foot of the display 7 Tilt the panel back to the foot Image 6 2 Placing the protection buffer K5902067 NIO 3MP LED DISPLAY 26 11 2014 6 Repackaging instructions 6 2 Repacking your display How to repack your display 1 Place the empty bottom box on a stable surface 2 Place the bottom buffer in the box 3 Put the display together with the protection buffer see Replacing the protection buffer page 34 in the dedicated cavity of the bottom buffer 4 Put the top buffer on top of the display 5 Slide the top box over the bottom box 6 Use the three lock bayonets to lock the box K5902
13. Nio 3MP LED Display User Guide MDNC 3321 K5902067 03 BARCO 26 11 2014 Visibly yours Barco nv President Kennedypark 35 8500 Kortrijk Belgium Phone 32 56 23 32 11 Fax 32 56 26 22 62 Support www barco com esupport Visit us at the web www barco com Printed in Belgium Table of contents TABLE OF CONTENTS 1 VVGIGOMEC a a O iatetacumeld tata oitove don akn dobo Dont 3 Wel ABOUT ING Proud os 3 WZ SMMOOIS a decias 3 To Whats IIED dee 4 2 Parts controls and connectors ccccccccccncnccoca canaria 5 21 Display TOM MIO ee do iaa 5 2 2 Display rear VICW aida dla 6 3 DISDIAV IAStalla OM ii A A A deaselauiee ies 9 31 Unlocking the height MECNANISIN iii AA AAA AAA AA As 9 3 2 Adjusting Ne SPA POSMOT lt ni een Homer Ne icon vi n oa ini 9 3 3 Removing the connector compartment cover e eee teen eee en eeennenes 10 3 4 Connecting the signal cables n nk 10 3 5 Routing the cables amp Reattach the connector compartment cover 12 9 0 VESA MOUNEINSIANAUON a cad 12 Of Firsttime staning UD ada 14 Ay Dally ODCTAllOM sv is 15 4 1 Recommendations for daily operation LL 15 42 SOY INGICATON NOMUS 24 403 e o ie 16 49 SAND SWICIING asta 16 44 Bringing Up the OSD MenuUS a A A A eos 17 4 5 Navigating through the OSD Menus 335365 a Males AA A Side 17 9 Advanced Opera
14. SD menus can be done by 1 If not already done so switch on the display as previously described 2 Illuminate the keys as previously described 3 While the keys are illuminated touch the menu key As a result the OSD main menu comes up in the bottom right corner of the screen However if no further actions are taken within the following 90 seconds the OSD will disappear again The OSD menu auto exit function can be disabled in the OSD menu Please refer to OSD menu automatic close function page 19 for detailed instructions on how to do this 4 5 Navigating through the OSD menus How to navigate through the OSD menus Navigating through the OSD menus can be done by e Use the left right keys to move through the sub menus change values or make selections e To go into a submenu or confirm adjustments and selections use the menu key e Use the standby key to cancel adjustments or exit a sub menu e Exit all OSD menus at once by touching the standby key for approximately 2 seconds N The key icons are displayed above the keys adapted to the function that it is used for menu dependent Overview key icons Menu Enter K5902067 NIO 3MP LED DISPLAY 26 11 2014 17 4 Daily operation Cancel l Standby IEC 60417 5009 eX 18 AA K5902067 NIO 3MP LED DISPLAY 26 11 2014 5 Advanced operation 9 ADVANCED OPERATION 5 1 OSD menu language About the OSD menu language By default the OSD men
15. V m 3 VIm used no closer to any IEC 61000 4 3 80 MHz to 2 5 GHz part or ine NIO SME EED Display including cables than the recommended separation distance calculated from the equation applicable to the frequency of the transmitter Recommended separation distance d 1 2VP d 1 2VP 80 MHz to 800 MHz d 2 3VP 800 MHz to 2 5 Ghz Where P is the maximum output power rating of the transmitter in watts W according to the transmitter manufacturer and d is the recommended separation distance in meters m Field strengths from fixed RF transmitters as determined by an electromagnetic site 1 is the a c mains voltage prior to application of the test level 2 Nio 3MP LED Display doesn t contain susceptible components to magnetic fields K5902067 NIO 3MP LED DISPLAY 26 11 2074 45 8 Important information Immunity test IEC 60601 Compliance level Electromagnetic environment guidance survey should be less than the compliance level in each freguency range Test levels Interference may occur in the vicinity of equipment marked with symbol 0 At 80 MHz and 800 MHz the higher freguency range applies R These guidelines may not apply in all situations Electromagnetic propagation is af fected by absorption and reflection from structures objects and people Recommended separation distance The Nio 3MP LED Display is intended for use in an electromagnetic environment in which r
16. adiated RF disturbances are controlled The customer of the user of the Nio 3MP LED Display can help prevent electromagnetic interference by maintaining a minimum distance between portable and mobile RF com munications equipment transmitters and the Nio 3MP LED Display as recommended below according to the maximum output power of the communications equipment Rated maximum output Separation distance according to frequency of transmitter power of transmitter 750kHz to 80MHz 80MHz to 800MHz 800MHz to 2 5GHz oo LE om ioe es s pr At 80 MHz and 800 MHz the separation distance for the higher frequency range applies 3 Field strengths from fixed transmitters such as base stations for radio cellular cordless telephones and land mobile radios amateur radio AM and FM radio broadcast and TV broadcast cannot be predicted theoretically with accuracy To assess the electromagnetic environment due to fixed RF transmitters an electromagnetic site survey should be considered If the measured field strength in the location in which the Nio 3MP LED Display is used exceeds the applicable RF compliance level above the Nio 3MP LED Display should be observed to verify normal operation If abnormal performance is observed additional measures may be necessary such as re orienting or relocating the Nio 3MP LED Display 4 Over the frequency range 150 kHz to 80 MHz field strengths should be less than 3 V m 5 For transmitters rated at a ma
17. arameters are stored in your display and determine the preset ambient light correction value to take into account to recalculate the DICOM display function when Ambient Light Compensation ALC is enabled Please refer to Ambient Light Compensation ALC page 24 to enable ALC K5902067 NIO 3MP LED DISPLAY 26 11 2014 5 Advanced operation The available reading rooms for your Nio 3MP LED Display are CR DR MAMMO Corresponds to light conditions in diagnostic reading rooms for computed radiology digital radiology or mammography This setting has the lowest maximum ambient light CT MR NM Corresponds to light conditions in diagnostic ES reading rooms for computed tomography magnetic resonance or nuclear medicine scans taff Office Corresponds to light conditions in office rooms Clinical Viewing Room Corresponds to light conditions in diagnostic reading rooms for clinical viewing Emergency Room Corresponds to light conditions in emergency rooms Operating Room Corresponds to light conditions in operating rooms This setting has the highest maximum ambient light To select a reading room 1 Bring up the OSD main menu 2 Navigate to the Configuration gt Calibration gt Ambient Light menu 3 Enter the Reading Room submenu 4 Select one of the available reading rooms and confirm 5 15 Embedded QA Overview e About Embedded QA e DICOM status report e DICOM compliance check e DICOM calibration e Reset DICOM
18. calibration e DICOM error threshold 5 15 1 About Embedded QA About Embedded QA allows you to run a display calibration or compliance test directly from the display using the OSD menus described in the next sections Embedded QA will use the front sensor l Guard to measure the necessary luminance levels for either a calibration or compliance test Various settings for both actions can be selected from the display s OSD menu The last results of both actions can be consulted from the OSD Embedded QA or MediCal QAWeb Embedded QA is not a replacement for the Barco MediCal QAWeb solution Although Embedded QA is a reliable option to perform a simple calibration or compliance test Barco still highly recommends MediCal QAWeb as the solution of choice for calibration and QA Medical QAWeb brings many benefits such as centralized asset management the ability to schedule tasks remote man agement automated reporting alerting and specific support of regional QA standards such as DIN 6868 57 JESRA and AAPM TG18 That s why MediCal QAWeb Agent acts as the master for all supported dis plays from the moment it is installed and running MediCal QAWeb Agent will take over from Embedded QA and overwrite any settings which were applied by Embedded QA K5902067 NIO 3MP LED DISPLAY 26 11 2014 25 5 Advanced operation 5 15 2 DICOM status report About DICOM status report Following information is available since last compliance check is com
19. ce must accept any interference received including interference that may cause undesired operation Interference can be determined by turning the equipment off and on If this equipment does cause harmful interference to or suffer from harmful interference of surrounding equipment the user is encouraged to try to correct the interference by one or more of the following mea sures e Reorient or relocate the receiving antenna or equipment e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced technician for help Electromagnetic immunity The Nio 3MP LED Display is intended for use in the electromagnetic environment specified below The customer or the user of the Nio 3MP LED Display should assure that it is used in such an environment Immunity test IEC 60601 Compliance level Electromagnetic environment Test levels E guidance Electrostatic discharge 6kV contact 6kV contact Floors should be wood ESD 8kV air 8kV air concrete or ceramic tile If floors are covered with IEC 61000 4 2 synthetic material the relative humidity should be at least 30 Electrical fast 2kV for power supply 2kV for power supply Mains power quality transient burst lines lines should be that of a typical commercial or hospital IEC 61000 4 4 1kV for input output 1kV fo
20. cted power supply also provides a switch that can be used to turn the power completely off To use the display please make sure to switch on this power supply This can be done by pushing the on off switch on the power supply into the position Switching on the display while it is in standby mode or vice versa can be done by 1 Illuminate the keys as previously described 2 While the keys are illuminated touch the standby key right button for approximately 2 seconds As a result the display will switch on or will switch to standby mode When the display is switched on the power LED is white When the display is in standby mode the power LED is orange The power LED can be disabled in the OSD menus Please refer to Power status indi cator light page 19 for detailed instructions on how to do this x In case of a power outage recovery your display will always start up in the power mode it was in before the power interruption i e standby or on This protects your display against inadvertent image retention problems K5902067 NIO 3MP LED DISPLAY 26 11 2014 4 Daily operation 4 4 Bringing up the OSD menus How to bring up the OSD menus The OSD menu allows you to configure different settings to make your Nio 3MP LED Display fit your needs within your working environment Also you can retrieve general information about your display and its current configuration settings through the OSD menu Bringing up the O
21. ent cover open oo ae k f DE o Image 2 3 Rear view with open connector compartment cover 24 VDC power input 5 VDC 0 5A power output DisplayPort video input DVI video input user application K5902067 NIO 3MP LED DISPLAY 26 11 2014 0 9 9 DO 2 2920 0 2 20 0 ae 0 0 0 0 20 05 0 0060 e D ERIO A POOO 00 060 12 2 0 01 0 010 0 0 0 00 09 0 o_o 0 Pe PLA 1200040 x eet ep 00 0 000 e oro POOR Vere ete rove Po ON 00 0 0 4 2 2 2 22 2 OOOO 22 O ON Pay o Ethernet connector see note below USB upstream connector USB downstream connector The Ethernet connection is used for maintenance purposes and is not supported for 2 Parts controls and connectors 8 K5902067 NIO 3MP LED DISPLAY 26 11 2014 3 Display installation 3 DISPLAY INSTALLATION Prior to installing your Nio 3MP LED Display and connecting all necessary cables make sure to have a suitable display controller physically installed in your computer If you are using a Barco display controller please consult the user guide delivered with it to do this 3 1 Unlocking the height mechanism To remove the clip 1 Position the display with its rear side facing you 2 Pull the red clip out of the fixation hole in the foot 3 Keep the clip in the dedicated hole in case the display needs to be shipped later 3 2 Adjusting the display po
22. evice must accept any interference re ceived including interference that may cause undesired operation This device has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This device generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this device does cause harmful interference to radio or television reception which can be determined by turning the device off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the device and receiver e Connect the device into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment Canadian notice This ISM device complies with Canadian ICES 001 Cet appareil ISM est conforme a la norme NMB 001 du Canada 8 4 EMC notice General informa
23. four screws fixing the foot while supporting the foot 6 Attach the arm stand firmly to the panel using 4 screws M4 x 8 mm 3 First time starting up Overview You are now ready to start up your Nio 3MP LED Display for the first time 1 Switch on your Nio 3MP LED Display as described in Standby switching page 16 2 Turn on the computer connected to your display If you have properly installed your display and display controller the Windows start up messages will appear once the boot procedure is finished Your Nio 3MP LED Display will be running in a basic video mode at a default refresh rate when first time starting up If you are using a Barco display controller please consult the user guide delivered with it to install the drivers software and documentation When this is done your display will automatically detect the connected video input signal s and apply the correct video mode and refresh rate K5902067 NIO 3MP LED DISPLAY 26 11 2014 4 Daily operation 4 DAILY OPERATION 4 1 Recommendations for daily operation Optimize the lifetime of your display Enabling the Display Power Management System DPMS of your display will optimize its diagnostic life time by automatically switching off the backlight when the display is not used for a specified period of time By default DPMS is enabled on your display but it also needs to be activated on your workstation To do this go to Power Options Propertie
24. hannel This mode is intended for grayscale displays where gray is sent over the green channel gray is sent over the blue channel Use All Channels This mode is intended for grayscale displays where gray is sent over the red green and blue channel This is done by means of a standard conversion mechanism where 30 red 59 green and 11 blue are used to generate gray K5902067 NIO 3MP LED DISPLAY 26 11 2014 29 5 Advanced operation To manually select a grayscale conversion mode 1 Bring up the OSD main menu 2 Navigate to the Configuration gt Image Source menu 3 Enter the Grayscale Conversion submenu 4 Select one of the available color conversion modes and confirm 9 21 EDID timings About EDID timings Following EDID timings are available for your Nio 3MP LED Display Refresh Rate Allows to manually select the refresh rate of the image source video input signal depending on the maximum refresh rate of the display controller connected to your display Preferred Orientation Allows to change the orientation of the image source video input signal to landscape portrait or to let the display automatically assign the correct orientation Color Depth slows to change the color depth to 8 or to 10 bit To manually set EDID timings 1 Bring up the OSD main menu 2 Navigate to the Configuration gt Image Source menu 3 Enter the Timings submenu 4 Select Refresh Rate Preferred Orientation or C
25. he box should not be cut with a knife a cutter or any other sharp object Indicates the temperature limits to which the medical device can be safely exposed when being stored Indicates the range of humidity to which the medical device can be safely exposed when being stored Indicates the range of atmospheric pressure to which the medical device can be safely exposed when being stored 8 6 Legal disclaimer Disclaimer notice Although every attempt has been made to achieve technical accuracy in this document we assume no responsibility for errors that may be found Our goal is to provide you with the most accurate and usable documentation possible if you discover errors please let us know Barco software products are the property of Barco They are distributed under copyright by Barco N V or Barco Inc for use only under the specific terms of a software license agreement between Barco N V or Barco Inc and the licensee No other use duplication or disclosure of a Barco software product in any form is authorized The specifications of Barco products are subject to change without notice Trademarks All trademarks and registered trademarks are property of their respective owners Copyright notice This document is copyrighted All rights are reserved Neither this document nor any part of it may be reproduced or copied in any form or by any means graphical electronic or mechanical including photocopying tap
26. ination is specified as a ME system e To avoid the risk of electric shock this equipment must only be connected to a supply mains with protective earth e The equipment should be installed near an easily accessible outlet e The equipment is intended for continuous operation Transient over voltage If the device is not used for a long time disconnect it from the AC inlet to avoid damage by transient over voltage K5902067 NIO 3MP LED DISPLAY 26 11 2014 39 8 Important information To fully disengage the power to the device please disconnect the power cord from the AC inlet Power cords e Utilize a UL listed detachable power cord 3 wire type SJ or equivalent 18 AWG min rated 250 V min provided with a hospital grade type plug 5 15P configuration for 120V application or 6 15P for 240V application e Do not overload wall outlets and extension cords as this may result in fire or electric shock e Mains lead protection U S Power cord Power cords should be routed so that they are not likely to be walked upon or pinched by items placed upon or against them paying particular attention to cords at plugs and receptacles e The power supply cord should be replaced by the designated operator only at all time e Use a power cord that matches the voltage of the power outlet which has been approved and complies with the safety standard of your particular country Water and moisture Never expose the display to rain or moistu
27. ing or information storage and retrieval systems without written permission of Barco O 2014 Barco N V All rights reserved Patent information This product is covered under the following intellectual property rights US Patent RE43 707 European Patent 1 915 875 K5902067 NIO 3MP LED DISPLAY 26 11 2014 49 8 Important information 8 7 Technical specifications 90 Overview Product acronym MDNC 3321 Screen technology UA SFT ultra advanced super fine technology H106 Active screen size diagonal 540 mm 21 3 Active screen size H x V 324 9 mm x 433 2 mm 12 79 x 17 1 Aspect ratio H V 4 3 Resolution AMP 2048 x 1596 Gray imaging N Viewing angle H V Number of grayscales LUT 1024 gray levels 10 12 In LUT out Uniform Luminance Yes Technology ULT Per Pixel Uniformity PPU No Ambient Light Compensation No ALC Backlight Output Stabilization Yes BLOS DICOM calibrated luminance 400 cd m ULT off Contrast ratio ULT off 1400 typical Response time Tr Tf 40 ms Scanning frequency H V 15 129 kHz 24 100 Hz Yes Power save mode DVI DMPM 280 MHz Power management English German French Dutch Spanish Italian Portugese Polish OI U n Ul o O S oil O 0 Russian Swedish Chinese simplified Japanese Korean Arabic Dimensions with stand W x H Portrait w x hmax x d 375 x 620 x 235 mm w x hmin x d 375 x 520 x 235 m
28. m Landscape w x hmax x d 488 x 563 x 235 mm w x hmin x d 488 x 463 x 235 mm W x H 1375 x 488 x 84 mm x x U 5 YD O 5 0 m o 0 pe o Dimensions packaged W x H 1686 x 342 x 585 mm Net weight with stand 3 kg X K5902067 NIO 3MP LED DISPLAY 26 11 2014 8 Important information Net weight w o stand 8 kg Net weight packaged with 17 kg stand Net weight packaged w o stand N A Height adjustment range 100 mm Tilt 5 25 wivel 30 30 Pivot N A VESA 100 mm Protective non reflective glass cover Recommended modalities CT MR US DR CR NM Film Certifications CE0120 MDD 93 42 EEC A1 2007 47 EC class IIb product CE 2004 108 EC CE 93 42 EEC A1 2007 47 EC class II b IEC 60950 1 2005 A1 2009 2ND EDITION IEC 60601 1 2005 A1 2012 ANSI AAMI ES 60601 1 2005 C1 2009 A1 2012 CAN CSAC22 2 No 60601 1 08 2008 DEMKO EN 60601 1 2006 EN 60601 1 2 2007 CCC GB9254 2008 GB4943 1 2011 GB17625 1 2003 KC VCCI FCC class B ICES 001 Level B FDA 510 k RoHS Mounting standard creen protection Supplied accessories Quick Installation Sheet 1 x DVI Dual Link 1 x DisplayPort Main cables UK European CEBEC KEMA USA UL CSA adaptor Chinese CCC C v m G o lt o O O a ep E Ko Z m lt gt gl O1 U External power supply OR sofware MECA DAVE Operating temperature OC to 40 C 1
29. nfident diagnoses On demand image quality checks As the front sensor works seamlessly together with Barco s online MediCal QAWeb service for automated Quality Assurance and calibration Nio 3MP LED Display makes sure you are viewing perfect DICOM images at the click of a button without interrupting your workflow A good investment Using power efficient LED backlights Nio 3MP LED Display is as low in power consumption as it is high in brightness Because it uses less power the display produces less heat and requires less cooling which impacts maintenance and operational costs Additionally the LED backlights offer a long lifetime even at high brightness providing a high return on your investment CAUTION Read all the important safety information before installing and operating your Nio 3MP LED Display Please refer to the dedicated chapter in this user guide 1 2 Symbols Symbols in this document The following symbols are used in this document B e B Info term definition General info about the term K5902067 NIO 3MP LED DISPLAY 26 11 2014 3 7 Welcome Note gives extra information about the described subject Tip gives extra advice about the described subject 1 3 What s in the box Overview Your Nio 3MP LED Display comes with e the display e a system tilt and swivel foot e this Nio 3MP LED Display user guide e asystem CD e a DisplayPort cable e a DVI cable e an USB cable
30. nland is included in the MCV standard of the Ministry of Information Industry of China in the section Limit Requirements of toxic substances in Electronic Information Products SN E 4 M Am A SDR RICH Component name Hazardous substances and elements EN fil E FS Ae E Printed Circuit Assemblies 82 Ge TED A LCD panel IHR E E External Cables sd Internal wiring BN Metal enclosure BIR Plastic enclosure ANIA FT 2 Heatsinks EB JR HE DY a Power Supply Unit XA Fan K5902067 NIO 3MP LED DISPLAY 26 11 2014 AAA 8 Important information 42 HE 2 M Am AS DIR RICH Component name an susie and elements im AT ER SRA Cr6 R pes EE pes EE manual O RT R SES MAEUZE a Lu SJ T 11363 2006 M M rear O Indicates that this toxic or hazardous substance contained in all of the homogeneous materials for this part is below the limit reguirement in SJ T11363 2006 X RTE 52 SUM E DATA ADE HR M KA E St SJ T 11363 2006 17 AL JE HT REZA X Indicates that this toxic or hazardous substance contained in at least one of the homogeneous materials used for this part is above the limit requirement in SJ T11363 2006 EPR A Mt ARA FE RS m EIP ADM ROR AMBER BRE MR ER MA DE E 38 GR 56 FA HA BR EFUP Barco m FT X AHJEFUPRS ESRB BARDA A F ll ERA Fh EA B E A BIE FAIRE U PT All Electronic Information Products EIP that are sold within Chinese Mainland must comply with the Electronic Info
31. olor Depth 5 Select one of the available settings and confirm 5 22 Display info About display info Your display serial number color type native resolution firmware versions etc are available in a dedi cated submenu of the OSD menu To retrieve info about your display 1 Bring up the OSD main menu 2 Navigate to the About this Display menu to make the information visible on the screen 5 23 Display status 30 About display status The Status submenu of the OSD menu provides info on the current status of your display runtimes tem peratures etc the status of the connected image sources video encoding mode timings etc the current calibration status of your display display function luminance ALC etc and the status about activated connections K5902067 NIO 3MP LED DISPLAY 26 11 2014 5 Advanced operation To retrieve the status of your display 1 Bring up the OSD main menu 2 Navigate to the Status menu 3 Enter the Display Image Sources Calibration or Connectivity submenu as desired K5902067 NIO 3MP LED DISPLAY 26 11 2014 3 5 Advanced operation 32 K5902067 NIO 3MP LED DISPLAY 26 11 2014 6 Repackaging instructions 6 REPACKAGING INSTRUCTIONS WARNING Before repacking the display follow the instruction to replace the protection buffer to prevent damage to the display Overview of the packaging Image 6 1 Packaging
32. onnectors on the device K5902067 NIO 3MP LED DISPLAY 26 11 2014 47 8 Important information Indicates the DisplayPort connectors on the device Indicates the manufacturing date EU Indicates the temperature limitations for the device to safely operate within specs at Ln Indicates the device serial no Warning dangerous voltage Caution Consult the operating instructions Indicates this device must not be thrown in the trash but must be recycled according to the European WEEE Waste Electrical and Electronic Equipment directive ete Indicates Direct Current DC Indicates Alternating Current AC Stand by Equipotentiality 6 Symbols on the box On the box of the device you may find the following symbols nonrestrictive list Indicates a medical device that can be broken or damaged if not handled carefully when being stored Indicates a medical device that needs to be protected from moisture when being stored Indicates the storage direction of the box The box must be transported handled and stored in such a way that the arrows always point upwards z p 6 Values for xx and yy can be found in the technical specifications paragraph 48 zz K5902067 NIO 3MP LED DISPLAY 26 11 2014 6 Important information Indicates the maximum number of boxes to be stacked on each other Indicates that the box should be carried with two persons Indicates that t
33. our display might not always sup port all these video encoding modes Standard This mode uses the standard 8 bit encoding mechanism HDR1 This mode features 10 bit video encoding following the High Dynamic Range HDR standard usually used on color displays HDR2 HDR2 is a Barco specific mode featuring 10 bit video encoding following the High Dynamic Range HDR standard but allowing full refresh rate which is not always possible with HDR1 This mode is usually used on color displays Dual 10 only with Barco display controller Dual 10 is a Barco specific 10 bit video encoding mode which is usually used on grayscale displays and which allows full refresh rate Automatic When selecting this option your Nio 3MP LED Display will automatically assign the correct video encoding settings to the connected video input signals To manually select a video encoding mode 1 Bring up the OSD main menu 2 Navigate to the Configuration gt Image Source menu 3 Enter the Video Encoding submenu 4 Select one of the available video encoding modes and confirm 5 20 Grayscale conversion modes About grayscale conversion modes Grayscale conversion modes specify how color generated on the display controller is converted to grayscale in your display The available grayscale conversion modes are No Conversion TO Use Red Channel This mode is intended for grayscale displays where gray is sent over the red channel Use Green C
34. play controller by using the DVI or the DP connection The input selection of the device is automatically done By default the DisplayPort input has priority over the DVI input This can be changed in the OSD menu K5902067 NIO 3MP LED DISPLAY 26 11 2014 3 Display installation 1 Connect the DVI or DP of the display controller to the DVI or DP connector of the display 2 If you want to make use of the display s USB upstream connector connect a PC USB downstream connector to the display s USB upstream connector 3 If you have chosen to use the displays USB downstream connector connect a USB device to the downstream connector 4 Connect the supplied external DC power supply to the 24 Vdc power input of the display 5 Plug the mains connector of the external DC power supply to a grounded power outlet by means of one of the supplied power cables K5902067 NIO 3MP LED DISPLAY 26 11 2014 11 3 Display installation 3 9 Routing the cables amp Reattach the connector compartment cover To route the cables 1 Route all connected cables through the cable routing channel in the stand of your display ocaci n IA SSSR et Rens ere ie ete SS ae Tip Thecable straps at the inside of the connector compartment allow you to fix the cables for better shielding of the cables To Reattach the connector compartment cover 1 Reattach the connector compartment cover by sliding the cover s bottom in position and then
35. pliance check will be OK To set the DICOM error threshold 1 Bring up the OSD main menu 2 Navigate to the Configuration gt Calibration gt Embedded QA menu 3 Enter the DICOM preferences submenu 4 Set DICOM error threshold as desired and confirm 9 16 Image scaling About image scaling Enabling image scaling will multiply each individual pixel to one or more adjacent pixels so that the size of the displayed image will be a multiple of the original image source video input signal Image scaling is only possible when the resolution of your display s video input signal is less than or equal to half the maximum resolution of the display K5902067 NIO 3MP LED DISPLAY 26 11 2014 2 5 Advanced operation To enable disable image scaling 1 Bring up the OSD main menu 2 Navigate to the Configuration gt Image Source menu 3 Enter the Scaling submenu 4 Select Enabled Disabled as desired and confirm 9 17 Display orientation About Display orientation Your display automatically detects its physical orientation portrait or landscape and by default automat ically adjusts the image orientation to this This means that when your display is physically rotated the image will rotate along The OSD menu however allows to overrule this behavior and force the image orientation to portrait or landscape regardless of the physical orientation of the display This may be especially useful when oper ating yo
36. pliant or not Maximum error Shows the maximum error of the current DICOM curve This is the deviation compared to a perfect DICOM Error threshold Shows the error threshold This is ees fi maximum error allowed before a DICOM calibration is required compliance check last compliance check function Ambient light compensation Shows the ambient light compensation status Reading Room hows the selected reading room Luminance Shows the measured luminance Black luminance Shows the measured backlight luminance DICOM Calibration Status No calibration executed yet No other information is visible Calibration executed When the calibration is executed the following extra information is shown Backlight runtime elapsed since latest calibration display function ambient light compensation reading room function Ambient Light Compensation Shows the ambient light PT ompensaion situs l Reading room Shows the selected reading room To retrieve the DICOM status report 1 Bring up the OSD main menu 2 Navigate to the Configuration gt Calibration gt Embedded QA menu 3 Select DICOM Status report to make the information visible on the screen 5 15 3 DICOM compliance check 26 About DICOM compliance check The DICOM compliance check will measure the DICOM curve of your display in different steps After measurement the DICOM status report is shown To start DICOM compliance check 1 Bring up the OSD main menu
37. push the cover s top You ll hear a click sound of the covers clips when the connector compartment cover is in position 3 6 VESA mount installation YN CAUTION Use suitable mounting apparatus to avoid risk of injury WARNING Never move a display attached to an arm by pulling or pushing the display itself Instead make sure that the arm is equipped with a VESA approved handle and use this to move the display Please refer to the instruction manual of the arm for more information and instructions K5902067 NIO 3MP LED DISPLAY 26 11 2014 3 Display installation dard Use an arm that can support the weight of the display Refer to the technical specifica tions of this display for the applicable weight YN WARNING Use an arm that is approved by VESA according to the VESA 100 mm stan Overview The panel standard attached to the tilt amp swivel foot is compatible with the VESA 100 mm standard So it can be used with an arm stand according to the VESA 100 mm standard Therefore the tilt 8 swivel foot must be removed from the panel 1 Put the display in the lowest position and fasten the height mechanism see Unlocking the height mechanism page 9 2 Put the display face down on a clean and soft surface Be careful not to damage the panel screen 3 Remove the plastic cover with a flathead screw driver K5902067 NIO 3MP LED DISPLAY 26 11 2014 AAA 3 Display installation 5 Remove the
38. quired to be able to use this functionality x Enabling the USB endpoint is only recommended when you are using a non Barco dis play controller If you are using a Barco display controller this communication will au tomatically be done over the connected video cable s To enable disable USB 1 Bring up the OSD main menu 2 Navigate to the Configuration gt Connectivity menu 3 Enter the USB submenu 4 Select Enabled Disabled as desired and confirm 5 8 DPMS mode About DPMS mode Enabling the Display Power Management System DPMS mode on your display will optimize its diagnos tic lifetime by automatically switching off the backlight when the display is not used for a specified period of time By default DPMS mode is enabled on your display but it also needs to be activated on your workstation To do this go to the Power options properties window of your workstation Barco recommends setting DPMS activation after 20 minutes of non usage CS When DPMS mode is enabled on your display an additional OSD power saving function becomes available hibernate Please refer to Hibernate page 22 for more information on hibernation and how to enable this function To enable disable DPMS mode on your display 1 Bring up the OSD main menu 2 Navigate to the Configuration gt Power Management menu 3 Enter the DPMS Mode submenu 4 Select Enabled Disabled as desired and confirm K5902067 NIO 3MP LED DISPLAY
39. r input output environment lines lines Surge 1 KV line s to line s 1 kV line s to line s Mains power quality IEC61000 4 5 2 kV line s to earth 2 kV line s to earth SMOUId be that of a typical commercial or hospital environment K5902067 NIO 3MP LED DISPLAY 26 11 2014 8 Important information Immunity test IEC 60601 Compliance level Electromagnetic environment Test levels guidance Voltage dips short lt 5 Ur 1 gt 95 dip in lt 5 Ur gt 95 dip in Mains power quality interruptions and voltage U for 0 5 cycle Ur for 0 5 cycle should by that of a vanalons ON power do 60 din 02 140 Us CO dip mus PPS commerciakor supply input lines hospital environment for 5 cycles for 5 cycles If the user of the Nio 000 70 U 30 dip in U 70 U 30 dip in Ur 3MP LED Display for 25 cycles for 25 cycles reguires continued operation during power mains interruptions it is recommended that the Nio 3MP LED Display be powered from an uninterruptible power supply or a battery Power frequency 50 60 Not applicable 2 Power frequency Hz magnetic field magnetic fields should IEC 61000 4 8 be at levels characteristic of a typical location in a typical commercial or hospital environment Conducted RF 3 Vrms Portable and mobile RF communications lt 5 Ur gt 95 dip in lt 5 Ur gt 95 dip in U for 5s Ur for 5s IEC 61000 4 6 150 kHz to 80 MHz equipment should be Radiated RF 3
40. re Never use the display near water e g near a bathtub washbasin swimming pool kitchen sink laundry tub or in a wet basement Ventilation Do not cover or block any ventilation openings in the cover of the set When installing the device in a cupboard or another closed location heed the necessary space between the set and the sides of the cupboard Installation Place the device on a flat solid and stable surface that can support the weight of at least 3 devices If you use an unstable cart or stand the device may fall causing serious injury to a child or adult and serious damage to the device This apparatus conforms to CE0120 MDD 93 42 EEC A1 2007 47 EC class llb product CE 2004 108 EC CE 93 42 EEC A1 2007 47 EC class II b IEC 60950 1 2005 A1 2009 2ND EDITION IEC 60601 1 2005 A1 2012 ANSI AAMI ES 60601 1 2005 C1 2009 A1 2012 CAN CSAC22 2 No 60601 1 08 2008 DEMKO EN 60601 1 2006 EN 60601 1 2 2007 CCC GB9254 2008 GB4943 1 2011 GB17625 1 2003 KC VCCI FCC class B ICES 001 Level B FDA 510 k RoHS National Scandinavian Deviations for CL 1 7 2 Finland Laite on liitett v suojamaadoituskoskettimilla varustettuun pistorasiaan Norway Apparatet m tilkoples jordet stikkontakt Sweden Apparaten skall anslutas till jordat uttag 8 2 Environmental information 40 Disposal Information Waste Electrical and Electronic Equipment x m This symbol on the product indicates that
41. rmation Products Pollution Control Labeling Standard of Chinese Mainland marked with the Environmental Friendly Use Period EFUP logo The number inside the EFUP logo that Barco uses please refer to the photo is based on the Standard of Electronic Information Products Environmental Friendly Use Period of Chinese Mainland Go China Energy Label FRERE lt lt Be R TH E EA gt gt AS SET Be FF D FER In accordance with The Regulation of the This monitor is compliant with the following Implementation on China Energy Label requirements RE dit SX BE Energy Efficiency cd W X i KAS ON HE HE Energy Consumption in off mode W BE IRE F EN Energy Efficiency Level TA T AY RE JR Re E ER AE GB 21520 2008 Code of National Standard applied K5902067 NIO 3MP LED DISPLAY 26 11 2014 8 Important information 8 3 Regulatory compliance information Indications for use The Nio 3MP LED Display is intended to be used as a tool in displaying and viewing digital images ex cluding digital mammography for review and analysis by trained medical practitioners Caution USA Federal law restricts this device to sale by or on the order of a physician Details amp exemptions are in the Code of Federal Regulations Title 21 801 Part D FCC class B This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this d
42. s in the Control Panel Barco recommends setting DPMS activation after 20 minutes of non usage CS Use a screen saver to avoid image retention Prolonged operation of an LCD with the same content on the same screen area may result in a form of image retention You can avoid or significantly reduce the occurrence of this phenomenon by using a screen saver You can activate a screen saver in the Display properties window of your workstation Barco recommends setting screen saver activation after 5 minutes of non usage A good screen saver displays moving content In case you are working with the same image or an application with static image elements for several hours continuously so that the screen saver is not activated change the image content regularly to avoid image retention of the static elements Understand pixel technology LCD displays use technology based on pixels As a normal tolerance in the manufacturing of the LCD a limited number of these pixels may remain either dark or permanently lit without affecting the diagnostic performance of the product To ensure optimal product quality Barco applies strict selection criteria for its LCD panels To learn more about LCD technology and missing pixels consult the dedicated white papers available at www barco com healthcare Enhance user comfort Every Barco multi head display system is color matched with the highest specifications in the market
43. s available in the technical spec ifications table The guaranteed backlight lifetime is valid for this setting 5 11 Viewing modes About viewing modes The Nio 3MP LED Display can be used in two viewing modes 22 D K5902067 NIO 3MP LED DISPLAY 26 11 2014 5 Advanced operation Diagnostic This mode provides the full calibrated luminance and is intended for using the display for diagnostic purposes Text In this mode the luminance is reduced to approximately half of the luminance This is intended for using the display with office applications such as word processing Please note that text mode is not persistent once powered off the unit will restart in diagnostic mode To quickly switch the viewing mode without having to enter the OSD menu touch the left and right key the two leftmost buttons at the same time during normal operation As the Nio 3MP LED Display is intended to be used in a diagnostic environment the diagnostic mode should always be selected To select a viewing mode 1 Bring up the OSD main menu 2 Navigate to the Configuration gt Calibration menu 3 Enter the Viewing Mode submenu 4 Select Diagnostic Text as desired and confirm 5 12 Display functions About display functions Native uncorrected panels will display all grayscale color levels with luminance increments that are not optimal for crucial diagnostic information Studies have shown however that in medical images
44. sition To adjust the display position 1 Stand at the front side of the panel and take the panel at both sides 2 Very important Tilt the panel upwards before changing the orientation 3 To change from portrait to landscape turn the panel counterclockwise 4 To change from landscape to portrait turn clockwise K5902067 NIO 3MP LED DISPLAY 26 11 2014 3 Display installation If after installing the display of the system you change the panel orientation while an image is on the screen the result depends on the graphic board and the resolution of the image In some cases the image will be rotated automatically in other cases it will not be rotated e g when pixels would be lost after rotation If necessary change the image resolution in the display control panel and restart the system after changing the orientation 3 3 Removing the connector compartment cover To remove the connector compartment cover 1 Gently push the two lips on top of the cover 2 Pull the top of the cover slightly away from the display and lift the cover upwards 3 4 Connecting the signal cables CAUTION Only connect one of the two video links Connecting both inputs simultane ously will result in driver errors To connect the signal cables to the display To get access to the connectors remove the connector compartment cover See Removing the connector compartment cover page 10 You may connect the display to a dis
45. t User Interface gt Indicator Lights menu 3 Enter the Power Status submenu 4 Select Enabled Disabled as desired and confirm K5902067 NIO 3MP LED DISPLAY 26 11 2014 19 5 Advanced operation 5 4 Key indicator lights About the key indicator lights By default after lighting up the key indicator lights will dim again if no further actions are taken within the following 5 seconds However this behavior can be changed so that the key indicator lights are always on or always off To configure the key indicator lights 1 Bring up the OSD main menu 2 Navigate to the Configuration gt User Interface gt Indicator Lights menu 3 Enter the Keys submenu 4 Select Automatic Always On Always Off as desired and confirm 5 5 Power lock function About the power lock function By enabling the power lock function the Nio 3MP LED Display is forced to remain switched on This means that it can t be switched to stand by mode manually until the power lock function is disabled again To enable disable the power lock function 1 Bring up the OSD main menu 2 Navigate to the Configuration gt User Interface gt Controls menu 3 Enter the Power Lock submenu 4 Select Enabled Disabled as desired and confirm 5 6 Ethernet over USB 20 About Eth over USB By default the Ethernet over USB will be disabled This does not disable the USB hub and still allows to make use of the display s USB downstream connectors and
46. ting instructions for future reference Adhere to all warnings on the device and in the operating instructions manual Follow all instructions for operation and use Electrical Shock or Fire Hazard To prevent electric shock or fire hazard do not remove cover No serviceable parts inside Refer servicing to qualified personnel Do not expose this apparatus to rain or moisture Modifications to the unit Do not modify this equipment without authorization of the manufacturer Type of protection electrical Display with external power supply Class equipment Degree of safety flammable anesthetic mixture Equipment not suitable for use in the presence of a flammable anesthetic mixture with air or with oxygen or nitrous oxide Non patient care equipment e Equipment primarily for use in a health care facility that is intended for use where contact with a patient is unlikely no applied part e The equipment may not be used with life support equipment e The user should not touch the equipment nor its signal input ports SIP signal output ports SOP and the patient at the same time Power connection Equipment with external 24 VDC power supply e Power requirements The equipment must be powered using the delivered medical approved 24 VDC SELV power supply e The medical approved DC power supply must be powered by the AC mains voltage e The power supply is specified as a part of the ME equipment or comb
47. tion No specific requirement on the use of external cables or other accessories except power supply With the installation of the device use only the delivered power supply or a spare part provided by the legal manufacturer Using another can result in a decrease of the immunity level of the device Electromagnetic emissions The Nio 3MP LED Display is intended for use in the electromagnetic environment specified below The customer or the user of the Nio 3MP LED Display should assure that it is used in such an environment oe oj Compliance Electromagnetic environment Guidance RF emissions Group 1 The Nio 3MP LED Display uses CISPR 11 RF energy only for its internal function Therefore its RF emissions are very low and are not likely to cause any interference in nearby electronic equipment K5902067 NIO 3MP LED DISPLAY 26 11 2014 AAA 8 Important information 44 Guidance CISPR 11 is suitable for use in all Harmonic emissions Class D establishments including IEC 61000 3 2 _ those directly connected to the Voltage fluctuations flicker Complies public low voltage power supply emissions network that supplies buildings IEC 61000 3 3 used for domestic purposes This Nio 3MP LED Display complies with appropriate medical EMC standards on emissions to and inter ference from surrounding equipment Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this devi
48. tliOn nasra toreo se Rada sata 19 SA OSD Menu lanGQuad eins tar rito an canoa 19 5 2 OSD menu automatic close function rn rr rr 19 5 9 Power status indicator lightos cese A A ees 19 54 NOV INOICAOPNIONIS EAN n ba Ad 20 DO JPOWENIOCK TUACION at dd 20 9 0 Ememetover USB sd a da 20 Ol A ee O PO DOV O enh ee an rena P ee ees 21 9 6 DPMS Mode si a rs 21 S9 AA E A O O E O O cie 22 S10 Luminance tard Siri tii 22 SAIT VICWING MOdES srta R O O A E EN 22 3 12 DI play TUCU Soi 23 5 13 Ambient Light Compensation ALC nc 24 3 14 Reading TOONS cia 24 Oo Os HE MID COO CUNO PPOR P E A PO O eee e E eee 25 9 19 L ADOUTEMDEQUT OA ii O A 25 M2 ICON ESTAS TODO ss A O A ia 26 MD DICOMNTCOMPIANCS CHECK orrira TR o 26 DS IC ONPCANDTAIOMERS RS A di ii voue 27 2150 ROS DGON CABTANOT odds da ios 27 39 15 60 DICOM error threshold dr 27 D 10 Mage SCANS dana 27 0 17 DISplay One nta ON nn scies centaines louise das 28 roto A no Qacecamteneeeeewarad l oo n edk sed 28 5 19 Video encoding MOVES NE O P P O C E O 28 5 20 Grayscale conversion Modes 2 2 K R P K K Kk 29 De BBA MMII ARR RR O O K cid dao O O ONE 30 3 22 DIPA MO nann de es Mb bye Be t oo a had D R o do dua 30 9 23 WISDIAY Stallone std ate dod nese kab ada dl sen AE ida 30 6 Repackaging instructions crop iii il 33 6 1 Replacing the ProlecHon DUMC LR i este vices A eae dere dies 34 K5902067 NIO 3MP LED DISPLAY
49. u comes up in English However there s a wide range of other languages avail able for the OSD menu of your Nio 3MP LED Display To change the language of the OSD menu 1 Bring up the OSD main menu 2 Navigate to the Configuration gt User Interface gt Menu menu 3 Enter the Language submenu 4 Select one of the available languages and confirm 5 2 OSD menu automatic close function About the OSD menu automatic close function By default the OSD menu will disappear automatically after approximately 90 seconds of inactivity How ever this function can be disabled so that the OSD menu remains on the screen until manually closed To enable disable the OSD menu automatic close function 1 Bring up the OSD main menu 2 Navigate to the Configuration gt User Interface gt Menu menu 3 Enter the Automatic Close submenu 4 Select Enabled Disabled as desired and confirm 9 3 Power status indicator light About the power status indicator light By default when the display is switched on the power status indicator light is dimmed This behavior can be changed so that the power status indicator light will be blue when the display is switched on When the display is in stand by mode the power status indicator light will always turn orange even when the power status indicator light is disabled To enable disable the power status indicator light 1 Bring up the OSD main menu 2 Navigate to the Configuration g
50. ur display with the screen facing upwards To set the Display orientation 1 Bring up the OSD main menu 2 Navigate to the Configuration gt Image Sources menu 3 Enter the Display Orientation submenu 4 Select Landscape Portrait Automatic as desired and confirm 9 18 Video input signals About input signals The available input signals for your display are DisplayPort 1 The input corresponding to the DisplayPort connector DVI 1 The input corresponding to the DVI connector Automatic Selection The input is automatically selected To manually select a video input signal 1 Bring up the OSD main menu 2 Navigate to the Configuration gt Image Source menu 3 Enter the Input Signal submenu 4 Select one of the available input signals and confirm 9 19 Video encoding modes About video encoding modes Video encoding modes specify how the color and luminance information is encoded in the video signal In consumer displays this is usually done by a limited 8 bit encoding mechanism Your Nio 3MP LED Display 28 D K5902067 NIO 3MP LED DISPLAY 26 11 2014 5 Advanced operation however features 10 bit encoding enabling it to better match the DICOM defined grayscale range Such an extensive range is necessary to comply with the guidelines set forward by the latest medical guidelines The available video encoding modes for your display are listed below a Please note that the display controller connected to y
51. ve copyrights You acknowledge living up to the conditions of each separate Open Source Software license A list of the Open Source Software components used is available in the applicable EULA through the customer section of the Barco website or through other online means K5902067 NIO 3MP LED DISPLAY 26 11 2014
52. ximum output power not listed above the recommended separation distance d in meters m can be estimated using the equation applicable to the frequency of the transmitter Where P is the maximum output power rating of the transmitter in watts W according to the transmitter manufacturer 46 E K5902067 NIO 3MP LED DISPLAY 26 11 2014 8 Important information x These guidelines may not apply in all situations Electromagnetic propagation is af fected by absorption and reflection form structures object and people 8 5 Explanation of symbols Symbols on the device On the device or power supply you may find the following symbols nonrestrictive list Indicates compliance with the Directive 93 42 EEC as Class device Indicates compliance with the Directive 93 42 EEC as Class II device Indicates compliance with Part 15 of the FCC rules Class A or Class B Indicates the device is approved according to the UL regulations Indicates the device is approved according to the UL regulations for Canada and US Indicates the device is approved according to the UL Demko regulations Indicates the device is approved according to the CCC regulations Indicates the device is approved according to the VCCI regulations Indicates the device is approved according to the KC regulations Indicates the device is approved according to the BSMI regulations Indicates the device is approved according to the PSE regulations Indicates the USB c

Barco Nio Color 3MP LED

Contents

Download Pdf Manuals

Related Search

Related Contents