Planar Systems PT3285PW
Contents
1. Please note the optional mount must be able to support at least 44 Ibs 20Kg Start Your Installation Please follow these instructions so that you can hook up the cables to associated connectors 1 Lay the display flat on an even surface and take off cable cover as seen in thestep 1 diagram 2 Connect the cables to the appropriate connectors as seen in the step 2 diagram 3 Take screw from the accessory box and put all cables under the cover lip then use a Philips Head screw driver insert the screw CBM M3x6 into cable cover and monitor as seen in the step 3 1 or step 3 2 diagram either Connecting the Display Figure 8 1 To setup this display please refer to the following figure and procedures 1 2 3 a Be sure all equipment is turned off Connect the AC power cord to the power connector on the monitor and the other end into an electrical outlet 8 1 Connect the D SUB or DVI cable from the display s VGA input connector to the D SUB or DVI connector of your host computer and tighten the screws 8 1 Connect the Audio In cable from the audio input port of your display to the Audio out port of your computer 8 1 Connect the USB cable from USB port of your display to USB port of your computer 8 1 Once the touch screen is configured the monitor is ready for use AN Notice To ensure the display works well with your computer please configure the display mode of your graphics card to make it less than2. Down button to select among the six functions in the main menu Choose the adjustment items by pressing the Select button Adjust the value of the adjustment items by pressing the Up or Down button With the OSD menu on screen press Menu button to return main menu or exit OSD The OSD menu will automatically close if you have left it idle for a pre set time To Lock the OSD Power menu buttons please follow the instructions below Please note the monitor has to be turned ON with a valid signal pre set a Press Menu key the OSD menu pops upon display b Press and hold the Menu key again with the OSD menu on the screen the OSD O O KO N menu will disappear Then press the Power key 1 time while the menu key is still being pressed The Lock Unlock menu will appear for 3 seconds c Use the Select key to select OSD or Power setting then set at Lock by pushing the UP or Down button d When the UP or Down button is released the previous setting will be saved and exit the Lock Unlock menu automatically 7 To Unlock the OSD Power menu buttons please follow the instructions below Please note the monitor has to be turned ON with a valid signal pre set a Press and hold the Menu key then press the Power key simultaneously the Lock Unlock menu will appear for 3 seconds b Use the Select key to select OSD or
3. Audio On Off control Appendix Troubleshooting If you are experiencing trouble with the display refer to the following If the problem persists please contact your local dealer or our service center Problem No image appears on screen gt Check that all the I O and power connectors are correctly and well connected as described in the Installation section gt Make sure the pins of the connectors are not crooked or broken Problem Partial Image or incorrectly displayed image gt Check to see if the resolution of your computer is higher than that of the display gt Reconfigure the resolution of your computer to make it less than or equal to 1920 x 1080 Problem Image has vertical flickering line bars gt Use Fine to make an adjustment gt Check and reconfigure the display mode of the vertical refresh rate of your graphic card to make it compatible with the display Problem Image is unstable and flickering Use Fine to make an adjustment Problem Image is scrolling gt Check and make sure the VGA signal cable or adapter is securely connected b Check and reconfigure the display mode of the vertical refresh rate of your graphics card to make it compatible with the display Problem Vague image characters and graphics gt Use Fine to make an adjustment If this problem still exists use Horizontal size to make an adjustment Problem Touch no function for Microsoft Windows
4. Power setting then set at Unlock by pushing the UP or Down button c When the UP or Down button is released the previous setting will be saved and exit the Lock Unlock menu automatically Please note a When the OSD Lock function is selected this indicates that all the buttons except power button are now disabled b When the Power Lock function is selected this indicates that the power key is disabled user can not to turn off the monitor by Power key On Screen Display Menus Main OSD Menu ITEM Contrast Brightness Auto Adjust Left Right Up Down Horizontal size Fine OSD Left Right OSD Up Down OSD Time out OSD Language Factory Reset RGB Volume Mute CONTENT The monitor luminance level control The monitor backlight level control Fine tune the image to full screen automatically Moving screen image horizontal position to left or right Moving screen image vertical position to up or down The screen image horizontal dot clock adjustment The screen image pixel phase adjustment Moving OSD menu horizontal position to left or right Moving OSD menu vertical position to up or down OSD auto disappear time selection OSD menu language selection English French Japanese Deutsch Spanish Italian Traditional Chinese and Simplified Chinese Factory default value restored Color temperature selection 9300K 6500K 5500K 7500K User Audio volume adjustment
5. or equal to 1920 x 1080 resolution and make sure the timing of the display mode is compatible with the display We have listed the compatible Video Modes of your display in the appendix on page 15 for your reference Figure 8 1 gt EE nooo aa AD m Controlling the PT3285PW monitor via RS 232 C Remote Control Optional The PT3285PW monitor can be controlled by connecting a PC with a RS 232C terminal diagramed below COM In COM Out COM In Two COM Ports are reserved for this option Before using the remote control function design a custom firmware based on your own application program and communication protocol Use null modem cable to enable it Note User Controls Rear Panel Controls MENU Menu A Up v Down 000 SELECT Select 200000000000 000000000000000 W Power Hine O0000 883888 o Menu disappear return to main item NN Brightness Main item select up Adjust up Main item select down Adjust down Auto Adjust Select sub item function Power On Off How to Use the OSD Menus GE MENU Menu A U v Down SELECT Select W Power aie Press the MENU button to pop up the on screen menu and press Up or
6. 00 000000000000 o ooooooooooooooo 900009 3288333888388883 383388 00000 y o Compatibility Modes Mode IBM VGA VESA SVGA VESA SVGA VESA XGA VESA SXGA VESA SXGA WXGA WSXGA VESA WXGA VESA WXGA VESA WXGA WSXGA Resolution 640X480 800X600 800X600 1024X768 1280X1024 1280X960 1440X900 1680X1050 1280X768 1280X720 1366X768 1920X1080 H Frequency khz 31 47 35 16 37 88 48 36 64 00 60 00 56 00 65 20 47 776 44 77 47 71 67 50 V Frequency hz 60 56 60 60 60 60 60 60 60 60 60 60 Touch Screen Driver Installation The PT3285PW Series is available with USB connection Please Note 1 The PT3285PW is Microsoft Windows HID Human Interface Device compatible if you use the USB touch screen interface No additional software driver is required for general operation of the touch screen 2 Microsoft Windows 7 operating system requires 15 seconds to recognize the PT3285PW after connecting the USB cable and power cable PT3285PW Calibration Tool Install ZN PLEASE NOTE 1 Calibration is required when using PT3285PW touch display for the first time or switching from monitor to PC Do not touch the screen during calibration tool execution process 2 The PT3285PW touch display is only compatible with Microsoft Windows 7 To use the Calibration Tool follow the instructions 1 Open the CD ROM 2 Select size 32 3 Select model PT3285PW 4 Run or sa
7. 7 only gt Microsoft Windows 7 operating system requires 15 seconds to recognize the PT3285PW after connecting the USB cable and power cable Warning Signal If you see warning messages on your screen this means that the display cannot receive a clean signal from the computer graphics card Below are the three kinds of Warning Signal Please check the cable connections or contact your local dealer or our service center for more information No Signal This message means that the display has been powered on but it cannot receive any signal from the computer graphics card Check all the power switches power cables and VGA DVI signal cable Going to Sleep The display is under the power saving mode In addition the display will enter power saving mode when experiencing a sudden signal disconnecting problem The monitor can be activated by pressing any keyboard triggering the mouse or touching the screen Out of Range This message means that the signal of the computer graphic card is not compatible with the display When the signal is not included in the Video Modes list we have listed in the Appendices of this manual the monitor will display this message imensions Product D 69mm 4 R13 786 1mm UILUZ OSY Side Vievv Front Vievv 590 0mm 400 0mm wuwo0 00 al uw Py Back View ok a 0090000000
8. PLANAR PT3285PW Touch Screen Edge lit LED LCD Monitor USER S GUIDE www planar com The information contained in this document is subject to change without notice This document contains proprietary information that is protected by copyright All rights are reserved No part of this document may be reproduced translated to another language or stored in a retrieval system or transmitted by any means electronic mechanical photocopying recording or otherwise without prior written permission Windows is a registered trademark of Microsoft Inc Other brand or product names are trademarks of their respective holders The test results show that this device meets the FCC rules Those limits are set to protect residential areas from the devices with harmful emission This device will produce use and radiate radio frequency energy In addition failure to follow the user s manual to install or use this device might produce harmful interference with radio communication Not withstanding the foregoing it does not guarantee that this type of harmful interference does not occur in some special installations The interference caused by this device to the reception of radio or television signals may be verified by turning it on and off Any changes or modifications to this TFT edge lit LED LCD would void the user s authority to operate this device For more information on how to recycle your product please visit WWW PLANARSYSTEMS COM GREEN Ta
9. ble of Contents Usage Notice PrECAUHONS tattoo tte 1 Introduction About PT3265P Ned aa a oo ee 2 Touch Screen Tor PAI IPN ibas 2 e NA AWA R A A PA EO e i 3 Installation PROGUCE OVERVIEW asia sko cu dy ADA A O DRAPAK O ias 4 Front W O ONE aa eae tied 4 BOOM VIEN a E EEE S A RE E E AE 4 VESA Mount for Your Moni cis 5 Start Your in stalla HO she ri ia aaa it a ios 6 Connecting the Display Figure 8 1 eeee eee neni e eee tike ei pe tete treni ee ee pe teen 7 EQU lin EE ERA add aa AO AAA Sub ena a O a aed 8 User Controls Rear Panel Control Saca ni Pan A Wok AO ROA Owo oO sie 9 How to Usethe OSD M NUS ico is 10 On Screen Display MENUS e A Aa ee eee 11 Appendix TROUDIGSNGOUINIG rt WE A 12 Warning SION de OSO EKO A GN EA Ua ONO RACE 13 NG IQA eo O AO e ao ets ar 13 Going AO SIEDZA Ol WA A RCA 13 OUGOlRan god aes cots A AA AO EAE AO aed 13 Product DIMENSIONS isis ida 14 Compatbility MODSSZ AZ ARNE dd Ph E E 15 Touch Screen Driver Installation e e ana nak aaa aaa aaa aaa aaa aaa aaa rete re terre rete re rere 16 PT3285PW Calibration Tool Install uueueeeaaea aaa aa aaa aaa RERE RR PRE ere ve ve ve eke vesi 16 Usage Notice ZN Warning To prevent the risk of fire or shock hazards do not expose this product to rain or moisture FAN Warning Please do not open or disassemble the product as this may cause electric shock Precautions Follow all warnings precauti
10. io 8W x 2 Touch Screen for PT3285PW Project Capacitive touch screen for finger input only e Surface Glare treatment Interface USB controller e Transmittance 90 5 HID Microsoft Windows 7 Package Overview Display USERS GUIDE aa can User s Guide Cable Cover Screw Power Cord Audio in Cable Touch Screen Driver Installation CD ROM DVI D Cable Landing Strip Installation Product Overview Front View Bottom View AUDIO OUT VESA Mount for Your Monitor This monitor conforms to the VESA Flat Panel Mounting Physical Mounting Interface standard which defines a physical mounting interface for flat panel monitors and corresponding with the standards of flat panel monitor mounting devices such as wall and table arms The VESA mounting interface is located on the back of your monitor To mount the monitor on a UL certified swing arm or other mounting fixture follow the instructions included with the mounting fixture to be used 400 0 mm 0900000009000 00 000000000800 00 200 0 mm oo 00 00 00 00 90 00 00 00 00 so 00 00 00 00 o o e 00000 883383 144 2 mm A Warning Please select the proper screws The distance between the back cover surface and the bottom of the screw hole is 8 mm Please use four M6 screws diameter with proper length to mount your monitor
11. ons and maintenance as recommended in this user s manual to maximize the life of your unit Do e Turn off the product before cleaning e Touch screen surface may be cleaned using a soft clean cloth moistened with mild window glass commercial cleaners or 50 50 mixture of water and isopropylalcohol Use a soft cloth moistened with mild detergent to clean the display housing Disconnect the power plug from AC outlet if the product is not going to be used for an extended period of time Don t e Do not touch the Display screen surface with sharp or hard objects Do not use abrasive cleaners waxes or solvents for your cleaning Do not operate the product under the following conditions Extremely hot cold or humid environment Areas susceptible to excessive dust and dirt Near any appliance generating a strong magnetic field In direct sunlight Introduction About PT3285PW The PT3285PW is a 31 5 flat panel screen with an active matrix thin film transistor TFT edge lit LED LCD Features include Direct Analog signal input Direct Digital signal input Active matrix TFT edge lit LED LCD technology 1920 x 1080 resolution 31 5 viewable display area 16 9 aspect ratio 31 47 67 5 KHz horizontal scan 47 63 Hz high refresh rate 0 36375mm x 0 36375mm pixel pitch Auto adjustment function Multilingual OSD user control 400mm x 200mm VESA mount Projected Capactive touch screen with USB controller Aud
12. ve calibration 5 Please do not touch the screen during calibration tool execution process Planar Systems Inc Customer Service 24x7 Online Technical Support http www planar com support 1195 NW Compton Drive Beaverton OR 97006 1992 Tel 1 866 PLANAR1 866 752 6271 or 1 503 748 5799 outside the United States Hours 24 hours a day 7 days a week 2013 Planar Systems Inc 1 13 Planar is a registered trademark of Planar Systems Inc Other brands and names are the property of their respective owners Technical information in this document is subject to change without notice 020 1170 01A 8204321A0103
Download Pdf Manuals
Related Search