ACTi B85 surveillance camera
Contents
1. The camera supports local video recording or saving of snapshots to a memory card NOTE Supports microSDHC and microSDXC cards How to Insert the Memory Card Insert a memory card into the card slot with the metallic contacts facing down the camera Push the card until it clicks into place How to Remove the Memory Card In case there is a need to remove the card make sure to access the camera Web Configurator to safely unmount the card first see the camera Firmware manual for more information Once unmounted from the firmware push the card to eject it from the slot 39 D4 ACTi Connecting Vision Hardware Manual Accessing the Camera Configure the IP Addresses In order to be able to communicate with the camera from your PC both the camera and the PC have to be within the same network segment In most cases it means that they both should have very similar IP addresses where only the last number of the IP address is different from each other There are 2 different approaches to IP Address management in Local Area Networks by DHCP Server or Manually Using DHCP server to assign IP addresses If you have connected the computer and the camera into the network that has a DHCP server running then you do not need to configure the IP addresses at all both the camera and the PC would request a unique IP address from DHCP server automatically In such case the camera will immediately be ready for the2. responsible party for compliance could void the user s authority to operate the equipment European Community Compliance Statement C 4 This product has been tested and found to comply with the limits for Class B Information Technology Equipment according to European Standard EN 55022 and EN 55024 In a domestic environment this product may cause radio interference in which cause the user may be required to take adequate measures 5 www acti com Bd ACTi Connecting Vision Hardware Manual Safety Instructions Cleaning Disconnect this video product from the power supply before cleaning Attachments Do not use attachments not recommended by the video product manufacturer as they may cause hazards Do not use accessories not recommended by the manufacturer Only install this device in a dry place protected from weather Servicing Do not attempt to service this video product yourself Refer all servicing to qualified service personnel Damage Requiring service Disconnect this video product from the power supply immediately and refer servicing to qualified service personnel under the following conditions 1 When the power supply cord or plug is damaged If liquid has been spilled or objects have fallen into the video product 3 Ifthe inner parts of video product have been directly exposed to rain or water Ifthe video product does not operate normally by following the operating Instructions in this manual
3. Outdoor Zoom Dome Series Hardware Manual B81 B84 B85 B87 2013 12 19 ACTI Connecting Vision va lt gt Bd ACTi Connecting Vision Hardware Manual Table of Contents RC UI ONS vaneen E l Safety MIS RUCHONS raare zenne peer nennen eene nnen gevens zeen nenen einden zeden 6 EE GG NO g On 7 The List of Model ana onnenenenenenenenmennmennsennsenmennmenene 7 Paekade GONIENIS oraaa 8 Physical Description essenties enteeneend een aeeaeweesesemaceueienaecuscameccusessaseasueads 9 Mounting OPHONS anneer deden seca O E a 11 Other Mounting Accessories usus enenenenennnen ennen ennen vennen ennn 13 Installing the Camera on a Surface 14 Step 1 Drill the ONC S annen 14 Step 2 Open the Dome Cover nennen ennen en nnnennane nnne 15 Step 3 Prepare for Waterproof Installation nennen 17 Waterproof Solution with Naked Cable ann eane nennen 18 Waterproof Solution with Conduit ann anann eneen en ennnen eenen 20 Step 4 Install the Camera to the Surface ann nnannnnanennanenn 24 Step 5 Connect the Cable nanne nnane nennen nanennane nennen 25 Step 6 Access the Camera Live VIEW ennnannenane nennen 26 Step 7 Adjust the Viewing Andie ssnsvsonnernsnentnsenssnndnbenenedednene 27 Step 8 Close the Dome COVver nanne nennen nnanennane nnne 28 Other Connections nonnen eenma nenneneenn 29 Connecting a Power Adapter Optional nee 29 Connecting the DI DO Devices Optional
4. nennen 31 Connecting Audio In Out Devices Optional neen 34 2 www acti com gt 3 ACT Hardware Manual Other Adjustments and Accessories 35 Replacing the Dome COVER uesiuorearsensentengsonkeveraalsdeosnsentundinenine dive ekien 35 Using a Memory Card assisia a aa a 39 How to Insert the Memory Card aaneen eneen en enen en ennn enenn 39 How to Remove the Memory Card aanne en enen eneen enen 39 Accessing the Camera aaneen mennnen 40 Configure the IP Addresses nnnennennenane nennen nennen nennen ennnrnnenn 40 ACCESS Ne CIMETA ensa EEEE EEEn 44 3 www acti com D4 ACTi Connecting Vision Hardware Manual Precautions Read these instructions You should read all the safety and operating instructions before using this product Heed all warnings You must adhere to all the warnings on the product and in the instruction manual Failure to follow the safety instruction given may directly endanger people cause damage to the system or to other equipment Servicing Do not attempt to service this video device yourself as opening or removing covers may expose you to dangerous voltage or other hazards Refer all servicing to qualified service personnel Trademarks All names used in this manual are probably registered trademarks of respective companies Liability Every reasonable care has been taken during the writing of this manual Please inform your local office if you fi
5. Adjust only those controls that are covered by the instruction manual as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the video product to its normal operation Safety Check Upon completion of any service or repairs to this video product ask the service technician to perform safety checks to determine if the video product is in proper operating condition 6 www acti com D4 ACTi Connecting Vision Hardware Manual Introduction The List of Models This hardware manual contains the following models 5MP Outdoor Zoom Dome with D N Adaptive IR Basic WDR 3x Zoom lens 1 3MP Outdoor Zoom Dome with D N Adaptive IR Basic WDR SLLS 3x Zoom lens 2MP Outdoor Zoom Dome with D N Adaptive IR Basic WDR SLLS 3x Zoom lens 3MP Outdoor Zoom Dome with D N Adaptive IR Superior WDR 3x Zoom lens From the installation perspective these models are very similar therefore you can use one manual for all of them www acti com ACTI Connecting Vision da Hardware Manual Package Contents me Mounting Screw Kit Hexagon Screwdriver Drill Template Conduit Gland Cable Gland 8 Terminal Block Terminal Block Terminal Block for Power iel DIDO for Audio In Out 8 www acti com Quick Installation Guide Warranty Card ACTI Connecting Vision da Hardware Ma
6. camera is already filled in the address bar of the browser lf you work with our cameras regularly then there is even a better way to discover the cameras in the network by using IP Utility The IP Utility is a light software tool that can not only discover the cameras but also list lots of valuable information such as IP and MAC addresses serial numbers firmware versions etc and allows quick configuration of multiple devices at the same time The IP Utility can be downloaded for free from http www acti com IP_Utility With just one click you can launch the IP Utility and there will be an instant report as follows IP Address NetMask 172 16 26 80 255 255 255 0 v Basic Search Refresh Device Settings Change Network Address Firmware Upgrade Config Backup Config Restore Reset Save amp Reboot Account Password 123456 Total 50 IP Address MAC Address FW Version Model Serial No Multicast IP Status 172 16 26 6 00 0F 7C 0A 3F EA A1D 500 V6 04 15 AC Megapixel IP Camera D31 A XX 13B 00159 228 5 6 1 172 16 26 7 00 0F 7C 0A 55 54 A1D 500 V6 04 15 AC Megapixel IP Dome E61 A XX 13C 00126 228 5 6 1 172 16 26 2 00 0F 7C 0A 93 52 A1D 500 V6 03 17 AC Megapixel IP Camera D42 A XX 13C 00132 228 5 6 1 172 16 26 13 00 0F 7C 0A 99 91 A1D 500 V6 04 15 AC Megapixel IP Dome E61 A XX 13D 00131 228 5 6 1 172 16 26 12 00 0F 7C 0A A1 0F A1D 500 V6 03 09 AC Megapixel IP Dome E92 A XX 13D 00321 228 5 6 1 172 16 26 90 00 0F 7C 0A A1 4
7. power adapter cable has two 2 different wires Connects to GND Pin White stripe Connects to 12V Pin xs ACTI Connecting Vision da Hardware Manual 3 Connect the wire with the white stripe to the 12V pin and the other to the GND pin 4 Tighten the screws of the 12V pin and the GND pins to secure the wire connection 5 Set the prepared power adapter for connection later Below is an example of a power adapter with an attached terminal block NOTE The power adapter is not bundled in the package 30 pd ACTI Connecting Vision Hardware Manual Connecting the DI DO Devices Optional Depending on your surveillance needs you may connect digital input or output devices to your camera to trigger events or notifications Digital Input DI devices can be used to notify the camera about an activity in the camera site DI can be triggers of events For example you can connect a panic button to the camera as such when the panic button is pressed the alarm signal will be sent through the camera Other common DI device applications are emergency button smoke detector passive infrared sensor etc Digital Output DO devices are external devices that are activated by the camera upon an event inside the camera For example you can connect an alarm horn to the camera as such when an event occurs inside the camera e g detected intruder
8. refer to the Knowledge Base article All about Digital Input and Digital Output downloadable from the link below http www acti com kb detail asp KB _ID KB20091230001 ACTI Connecting Vision da Hardware Manual Connecting Audio In Out Devices Optional Depending on your surveillance needs you may connect audio input or output device such as an active microphone or speaker to your camera In this case you need to connect the audio input output device to the supplied audio terminal block ns To connect audio input output devices map the pins to one of the pin combinations below Device Pin Mapping Instructions 1 GND Connect the wires of the audio output device to GND Audio Output Pin 1 and AUDIO OUT Pin 2 3 GND Connect the wires of the audio input device to GND Audio Input Pin 3 and AUDIO IN Pin 4 Press and hold the orange tab as you insert the wire through the pin slot then release the orange tab to secure the wire NOTE For more information about AUDIO in connections please refer to the Knowledge Base article How to Use Audio in of ACTi Cameras downloadable from the link below http www acti com support KnowledgeBase outside detail asp KB ID KB20100114003 34 ACTI Connecting Vision da Hardware Manual Other Adjustments and Accessories Replacing the Dome Cover For more discrete surveillance needs the bundled dome cover can be replaced wit
9. skip this step If the cable will pass through the surface do the following a Pull the network cable through the bottom conduit hole 22 ACTI Connecting Vision da Hardware Manual b Insert the sealing nut into the conduit gland body and then attach the clamping nut as tightly as possible to complete the cable solution 8 If connecting other cables attach the terminal blocks to the cables See Other Connections on page 29 9 Proceed with Step 4 Install the Camera to the Surface on page 24 23 DA ACTI Hardware Manual Step 4 Install the Camera to the Surface 1 Align the camera screw holes and the cable hole if necessary to the holes on the surface and attach the three 3 supplied screws with rubber to secure the camera A CAUTION When using electric screwdrivers be careful not to touch the internal camera components while attaching the screws Since electric screwdrivers vary in sizes speed and force they may bruise and damage the internal camera components DISCLAIMER ACTi will not be responsible for camera damage caused by improper installations or the misuse of equipment for installation 24 ACTI Connecting Vision da Hardware Manual Step 5 Connect the Cable 1 If the cable will be routed along the surface pull the network cable through the side conduit hole and attach the clamping nut to the conduit gland bod
10. 68 0 120 Later by pressing the Refresh button of the IP Utility you will be able to see the list of cameras with their new IP addresses Please note that it is also possible to change the IP addresses manually by using the Web browser In such case please plug in only one camera at a time and change its IP address by using the Web browser before plugging in the next one This way the Web browser will not be confused about two devices having the same IP address at the same time 13 pd ACTI Connecting Vision Hardware Manual Access the Camera Now that the camera and the PC are both having their unique IP addresses and are under the same network segment it is possible to use the Web browser of the PC to access the camera You can use any of the browsers to access the camera however the full functionality is provided only for Microsoft Internet Explorer The browser functionality comparison Functionality Internet Explorer Other browsers aa PTZ Conto Capture the snapshot Video overlay based configuration Motion yes No Detection regions Privacy Mask regions QuickTime http www apple com quicktime download has to be installed in PC first before using any non Internet Explorer browsers to be able to get live video feed from the camera with those browsers It is a free and open source cross platform multimedia player Disclaimer Notice The camera manufacturer does not guarantee the c
11. 9 and set Subnet Mask to 255 255 255 0 by using the steps below me lt All Control Panel Items Network and Sharing Center A E Ep een G es Control Panel Home i i ra o a Di ais Di View your basic network information and set up connections rganize v isable this network device iagnos Ch P EE ae See full map Er 7 a A Jo bo Kx Local Area Connection Ch d d shari J ae e SISO_NP_PC1 Network Internet Ue rn This computer ae Intel R 8 i Disable View your active networks Connect or disconnect Status Diagnose jp Network Access type Internet Work network Connections g Local Area Connection B Bridge Connections Create Shortcut Change your networking settings a Set up a new connection or network x Delete Set up a wireless broadband dial up ad hoc or VPN connection or set up a router or a Rename access point Properties Py Connect to a network ae Connect or reconnect to a wireless wired dial up or VPN network connection ee also HomeGroup Choose homegroup and sharing options Internet Options Access files and printers located on other network computers or change sharing Windows Firewall POE btocol Version 4 TCP IPv4 Properties LO jm bled ee ee Connect using amp Intel R 82567LM 3 Gigabit Network Connection You can get IP settings assigned automatically if your network supports this capability Otherwise you need to ask you
12. B ENR 010 V4 00 00 AC 16 CH Embedded NVR ENR1200 ENR1200 A 13D 00006 172 16 26 85 00 0F 7C 0B 36 8D A1D 500 V6 04 15 AC Hemispheric Camera E96 A XX 13H 00023 228 5 6 1 172 16 26 95 00 0F 7C 0B B7 50 A1D 500 V6 05 16 AC Hemispheric Camera BSS A XX 131 00007 16 26 00 0F 7C 8D F1 0A 1D 500 V6 05 f i 01 17 172 16 26 82 00 0F 7C 97 57 CD A1D 310 V4 12 09 AC Megapixel IP Camera TCM3511 12J X 00334 Ai Remove ea some 4 You can quickly notice the camera model in the list Click on the IP address to automatically launch the default browser of the PC with the IP address of the target camera filled in the address bar of the browser already ACTI Connecting Vision da Hardware Manual Use the default IP address of a camera If there is no DHCP server in the given network the user may have to assign the IP addresses to both PC and camera manually to make sure they are in the same network segment When the camera is plugged into network and it does not detect any DHCP services it will automatically assign itself a default IP 192 168 0 100 Whereas the default port number would be 80 In order to access that camera the IP address of the PC has to be configured to match the network segment of the camera Manually adjust the IP address of the PC In the following example based on Windows 7 we will configure the IP address to 192 168 0 9
13. Types Accessories Straight Wall Suitable when mounting the camera on straight walls Mount PMAX 0308 L Type Wall Mount PMAX 0101 PMAX 0305 Heavy Duty Wall Mount e gt Vertical Pole ouni PMAX 0101 PMAX 0305 gt Horizontal Pole Mount PMAX 0101 PMAX 0102 Corner Suitable when mounting the camera on a corner wall Mount PMAX 0101 PMAX 0305 PMAX 0402 2 ACTI Connecting Vision da Hardware Manual Other Mounting Accessories Accessories PMAX 0104 Extension Tube PMAX 0700 Junction Box e For more information about the mounting solutions and accessories please check the Mounting Accessory Selector in our website http www acti com mountingselector e The above mounting accessories are not included in the package Contact your sales agents to purchase 9 Bd ACTi Connecting Vision Hardware Manual Installing the Camera on a Surface This section describes the procedures in installing the camera on a flat surface such as a hard or dropped ceiling and straight or tilted walls Before installation make sure the wall or the ceiling can bear more than the weight of the camera Step 1 Drill the Holes Before drilling the holes on the ceiling or wall note the direction of the connectors side of the camera which is also the opposite side of the camera logo This influences the camera placement and where you should drill the hole where the cables will pass
14. access from the PC The user however might not know the IP address of the camera yet It is necessary to know the IP address of the camera in other to be able to access it by using a Web browser The quickest way to discover the cameras in the network is to use the simplest network search built in the Windows system just by pressing the Network icon all the cameras of the local area network will be discovered by Windows thanks to the UPnP function support of our cameras In the example below we successfully found the camera model that had just connected to the network pam eme el SIE network wg If Seorcrnewor Pl File Edit View Tools Help Organize Search Active Directory Network and Sharing Center Ft Favorites 0 B55 A XX 131 00007 Led D31 A XX 13B 00159 D42 A XX 13C 00132 D51 A 02 12H 00010 A XX 12L 00286 A XX 12L 00107 A XX 12K 00147 A XX 13C 00126 A XX 13D 00131 A XX 13A 00061 A XX 13A 00089 A XX 13D 00321 A XX 13H 00023 a Ji Downloads Recent Places de N a Libraries G T W W jM Computer m mom EB th Network ggg Q Q Q Q Q Q Q Q Q Q Q Q g B55 A XX 131 00007 Categories Other Devices Network location ACTi com www acti com ACTI Connecting Vision da Hardware Manual Double click on the camera model name the default browser of the PC is automatically launched and the IP address of the target
15. ce has a voltage of OV 30V or the DO device has a voltage of lt 24V lt 100mA then the camera can supply internal power to these devices and there is no need to connect the DI DO device to an external power source In this case wire connection to Pins 1 to 4 Use the GND and DI1 pins to connect a DI device and use the 12V and DO1 pins to connect a DO device See wiring scheme below NORMAL 3 1V NORMAL HIGH TRIGGER LOW BATTERY I 32 Bd ACTi Connecting Vision Hardware Manual Consequently to connect a second DI or DO device wire the connection to Pins 5 to 8 High Voltage DO Device Connection Even though the camera provides 12V power this may not be enough for some high voltage DO devices such as a Ceiling light or a motor that opens or closes a gate In this case there is a need to connect an external relay See wiring scheme below NORMAL HIGH TRIGGER LOW MOTOR Note that when choosing an appropriate relay please refer to its specifications and make sure they match the above design The triggering circuit voltage has to be around 12V DC and the switch controlled circuit voltage has to match the external power supply e g 110V AC or 220V AC The illustration below is a graphic example of connecting a relay to a high voltage DO device 110V 220V AC External Power Source Camera Illuminator NOTE For more information on DI DO connections please
16. e Firmware User Manual 1
17. g the dome cover 3 Carefully lift to open the dome cover and place it on the side of the camera NOTE Do not abruptly lift the dome cover it is attached to the camera with a spring wire www acti com ACTI Connecting Vision da Hardware Manual 4 If necessary insert a memory card with the metallic contacts facing down into the card slot of the camera 8 ACTI Connecting Vision da Hardware Manual Step 3 Prepare for Waterproof Installation The camera comes with two 2 glands used for waterproof installation e Cable Gland For use with an Exterior grade Ethernet cable Exterior grade Ethernet cables are already waterproof See Waterproof Solution with Naked Cable on page 18 e Conduit Gland For use with a flexible conduit This solution is recommended when an exterior grade Ethernet cable is not available or other cables such as power adapter DI DO devices etc will be connected to the camera See Waterproof Solution with Conduit on page 20 Determine the type of waterproof solution that is applicable to your installation requirements and prepare the necessary accessories or purchase extra materials Cable Gland Conduit Gland For use with an Exterior grade Ethernet For use with 1 2 flexible conduit not included in th k cable not included in the package included in the package 7 Bd ACTi Connecting Vision Hardware Man
18. h a smoke vandal proof cover available for purchase To replace the dome cover do the following 1 Loosen the three 3 screws to open the dome cover 2 Using a screwdriver remove the screw securing the spring wire to the dome cover NOTE Hold the spring wire as the screw is being removed to avoid the sudden release of the screw and cause it to fly in the air 3 Remove the three 3 screws to detach the cover bracket www acti com ACTI Connecting Vision bis Hardware Manual 4 Remove dome cover from the cover housing 5 Remove the rubber from the dome cover 6 Insert the rubber into the replacement dome cover 7 Insert the replacement dome cover into the cover housing S 6 ACTI Connecting Vision da Hardware Manual 8 There are 3 indents on the cover housing note the indent a which is on the center of the extended curve of the cover 9 Attach the three 3 screws to secure the bracket to the cover housing 37 ACTI Connecting Vision da Hardware Manual 10 Fit the screw into the spring wire that is attached to the camera Note the screw placement as shown below 11 There are two 2 screw holes on the bracket attach the screw to the right screw hole using a screwdriver 38 Ra ACT Hardware Manual Using a Memory Card
19. hen other cables such as power adapter DI DO devices etc will be connected to the camera 1 Prepare the following materials for waterproof installation Flexible Conduit Conduit Gland 1 2 Trade size included in the camera package not included in the package For use with 1 2 flexible conduit Network Cable CAT 5 or CAT 6 not included in the package 20 pd ACTI Connecting Vision Hardware Manual 2 Disassemble the bundled conduit gland as shown below I Nut Sealing Insert P i Nut wh NOTE In this installation the conduit gland body can be securely attached to the mount kit therefore the use of lock nut is not necessary Please set the lock nut aside 3 Pull the network cable through the flex conduit If connecting other input output devices or an external power adapter pull the cables through the flex conduit without connectors The terminal blocks will be attached once the cables pass through the camera hole later 4 Insert the clamping nut through the flex conduit a 2 ACTI Connecting Vision da Hardware Manual 5 Insert the sealing insert and attach it at the end of the flex conduit weet eeey tis T 6 Screw the conduit gland body to the conduit hole of the camera Attach to Side Conduit Hole Attach to Bottom Conduit Hole 7 Ifthe cables will be routed along the surface
20. her The easiest way to assign cameras the IP addresses is by using IP Utility IP_Utility IP Address NetMask 172 16 26 192 255 255 255 0 Basic Search T O Refresh Device Settings Change Network Address Firmware Upgrade Config Backup Config Restore Save amp Reboot a a Total 56 Account Password 123456 Http Port w IP Address MAC Address FW Version Model Serial No Multicast IP Status 172 16 26 2 00 0F 7C 07 DE 65 A1D 311 V5 07 05 AC Hemispheric Camera KCM3911 228 5 6 1 172 16 26 4 00 0F 7C 08 17 C2 A1D 310 V4 12 02 AC Mega IP Camera TCM1111 228 5 6 1 172 16 26 6 00 E aAA Fa KCM7311 228 5 6 1 172 16 26 7 00 TCM6630 228 5 6 1 172 16 26 10 00 Dynamic IP Address TCM4201 228 5 6 1 172 16 26 11 00 4 KCM3911 228 5 6 1 172 16 26 13 00 KCM5111 228 5 6 1 172 16 26 40 00 KCM5211 228 5 6 1 172 16 26 41 00 i KCM5311 228 5 6 1 172 16 26 50 00 3 z z KCM5111 228 5 6 1 172 16 26 52 00 ee _KcM5311 228 5 6 1 172 16 26 53 00 J TCM5311 228 5 6 1 172 16 26 54 00 TCM5611 228 5 6 1 172 16 26 55 00 En EN TCM5111 228 5 6 1 172 16 26 57 D 310 V4 12 09 TCD2100 228 5 6 1 172 16 26 61 TCM1231 228 5 6 1 Sess With the procedure shown above all the cameras will have unique IP addresses starting from 192 168 0 101 In case there are 20 cameras selected the last one of the cameras would have the IP 192 1
21. lt adjustment screws adjust the tilt and then tighten back the screws to fix the tilt position 2 Loosen the rotation adjustment screw rotate the viewing orientation and then tighten back the screw to fix the orientation 3 Loosen the pan adjustment screw move the pan direction and then tighten back the screw to fix the pan position 7 ACTI Connecting Vision da Hardware Manual Step 8 Close the Dome Cover 1 Tighten the three 3 screws to attach the dome cover to the camera body 2 Remove the plastic covering the dome cover Final installation will look like the illustration below 28 D4 ACTi Connecting Vision Hardware Manual Other Connections This section describes the procedures in preparing the external devices that you can connect to the camera The camera supports DC12V power input Digital Input and Output DI DO and Audio Input and Output devices using the bundled terminal blocks The use of these devices however is optional Connecting a Power Adapter Optional In case of using a non PoE switch or your PoE switch has limited power supply you can purchase a power adapter and directly connect the camera to a power outlet The power adapter must be connected to the supplied terminal block before use To do this follow the procedures below 1 Loosen the screws of the 12V and GND pins of the power terminal block 2 Take note that a standard
22. nd any inaccuracies or omissions We cannot be held responsible for any typographical or technical errors and reserve the right to make changes to the product and manuals without prior notice 4 www acti com D4 ACTi Connecting Vision Hardware Manual Federal Communications Commission Statement This equipment has been tested and found to comply with the limits for a class B C digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help Warning Changes or modifications to the equipment that are not expressly approved by the
23. nual Physical Description 1 Ethernet Port Connects to a network using an Ethernet cable 2 Memory Card Slot Insert a memory card into this slot for local recording purposes See Using a Memory Card on page 39 for more information NOTE Supports microSDHC and microSDXC cards 3 Digital Input Output DI DO This connector connects to digital input or output devices such as an alarm trigger panic button etc Digital Input DI and Digital Output DO devices are used in applications like motion detection event triggering alarm notifications etc See Connecting the DI DO Devices Optional on page 31for information on how to connect DI DO devices to your camera 4 Audio Input Output This connector connects to audio input and output devices such as microphones and speakers using the bundled terminal block See Connecting Audio In Out Devices Optional on page 34 for more information 9 www acti com Bd ACTi Connecting Vision Hardware Manual 5 DC 12V Power Input In case the camera is connected to a non PoE Power over Ethernet switch use this connector to connect the camera to an external power adapter not included See Connecting a Power Adapter Optional on page 29 for more information 6 Reset Button The purpose of reset button is to restore the factory default settings of the camera including the administrator s password The reset button can be used for following pur
24. ompatibility of its cameras with QuickTime since it is a third party software the third party has the right to modify their utility any time which might affect the compatibility In such cases please use Internet Explorer browser instead When using Internet Explorer browser the ActiveX control for video stream management will be downloaded from the camera directly the user just has to accept the use of such control when prompted so No other third party utilities are required to be installed in such case The examples in this manual are based on Internet Explorer browser in order to cover all functions of the camera 1 Bd ACTi Connecting Vision Hardware Manual Assuming that the camera s IP address is 192 168 0 100 you can access it by opening the Web browser and typing the following address into Web browser s address bar http 192 168 0 100 Upon successful connection to the camera the user interface called Web Configurator would appear together with the login page The HTTP port number was not added behind the IP address since the default HTTP port of the camera is 80 which can be omitted from the address for convenience Web Configurator x Web Configurator Account Password Language English v Login Reset Before logging in you need to know the factory default Account and Password of the camera Account Admin Password 123456 For further operations please refer to th
25. poses 1 The administrator s password has been forgotten and therefore the camera cannot be accessed 2 Incase of IP address mask or allow deny filter related issues resulting with inability to modify these settings 3 Incase of connectivity issues or abnormal video quality How to do the reset properly Press and hold the reset button for 5 seconds 10 ACTI Connecting Vision da Hardware Manual Mounting Options There are several mounting options that you can use to install the camera Select the most suitable solution for your installation environment Mount Types Accessories Surface Suitable when mounting the camera directly walls or ceilings Mount without extra accessories See Installing the Camera on a Surface on page 14 for mounting instructions Flush Mount Suitable when mounting the camera discretely above dropped ceilings wherein only the dome cover will be visible underneath the ceiling PMAX 1013 Gang Box Suitable for locations which require the use of gang boxes The Converter Gang Box Converter is attached to the gang box and the camera is installed on the Gang Box Converter All cables are hidden inside the gang box PMAX 0804 Pendant Suitable when mounting the camera on hard and high ceilings Mount PMAX 0101 PMAX 0103 Straight Tube with Bracket PMAX 0101 PMAX 0102 Straight Tube a _ 1 ACTI Connecting Vision da Hardware Manual Mount
26. r network administrator for the appropriate IP settings Obtain an IP address automatically This connection uses the following items a Use the following IP address o Client for Microsoft Networks Sl VirtualBox Bridged Networking Driver laos Packet Scheduler File and Printer Sharing for Microsoft Networks Intemet Protocol Version 6 TCP IPv6 IP address 192 168 0 99 Subnet mask Pt a ae LG 0 Default gateway intemet Protocol Version 4 TCP Pv4 Link Layer Topology Discovery Mapper 1 0 Driver Link Layer Topology Discovery Responder Obtain DNS server address automatically IEEE ES ER Use the following DNS server addresses Description Transmission Control Protocol Intemet Protocol The default wide area network protocol that provides communication across diverse interconnected networks Preferred DNS server Alternate DNS server en F Validate settings upon exit s 2 OK Cancel ACTI Connecting Vision da Hardware Manual Manually adjust the IP addresses of multiple cameras If there are more than 1 camera to be used in the same local area network and there is no DHCP server to assign unique IP addresses to each of them all of the cameras would then have the initial IP address of 192 168 0 100 which is not a proper situation for network devices all the IP addresses have to be different from each ot
27. the alarm horn will sound Other common DO device applications are motion triggered lights electric fence magnetic door locks etc You can connect up to two DI and two DO devices to your camera Press and hold the orange tab as you insert the wire through the pin slot then release the orange tab to secure the wire 1 2 3 4 5 6 7 8 To connect input devices DI map the pins to one of the pin combinations below Device Pin Mapping Instructions Digital Input 1 Connect the wires of the first input device to GND DI Pin 1 and DH Pin 3 Digital Input 2 Connect the wires of the second input device to GND DI2 Pin 5 and DI2 Pin 7 www acti com Pp ACTI Connecting Vision Hardware Manual To connect output devices DO map the pins to one of the pin combinations below Device Pin o Mapping Instructions Digital Output 1 Connect the wires of the first output device to 12V DO1 Pin 2 and DO1 Pin 4 Digital Output 2 6 lv Connect the wires of the second output device to 12V DO2 8 ooe Pin 6 and DO2 Pin 8 The table below shows the DI DO connection specifications Device Connection design TTL compatible logic levels To trigger low Logic level 0 OV 0 4V Voltage Normal ae Logic level 1 3 1V 30V Current 10mA 100mA Connection design Transistor Open Collector Voltage amp Current lt 24V DC lt 100mA Typical Connection Based on these specifications if the DI devi
28. through or how the cables will go along the ceiling or wall 1 Attach the supplied drill template on the surface according to the preferred camera orientation 2 Determine how the cables will be routed pass through the surface or along the surface e Ifthe cables will pass through the surface drill the cable hole and the three 3 screw holes on the surface R506 00289 000 ie Cable hole Dil Hole Drill Template scale 1 1 2B gill Hole Ze hed e o 5 Drill Holesse AN e s dent e Ifthe cables will be routed along the surface just drill the three 3 screw holes on the surface 3 Detach the drill template from the surface and insert the plastic plugs into the screw holes 4 ACTI Connecting Vision da Hardware Manual Step 2 Open the Dome Cover NOTE To avoid scratches or leaving fingerprints on the dome cover it is recommended to retain the plastic covering the dome cover until the camera is completely installed However the plastic has been removed on some of the pictures in this documentation to show clarity of the procedures being described 1 If the cables will pass through the surface remove the metal cap covering the bottom hole of the camera and attach the cap to the side hole to close it The cables will be routed to pass this hole from the surface P 2 With the bundled hex screwdriver loosen the three 3 screws securin
29. ual Waterproof Solution with Naked Cable This section describes the procedures in using the bundled cable gland and an exterior grade Ethernet cable 1 Disassemble the cable gland as shown below Body Sealing Insert Clamping with Washer with Claw Nut 2 Insert the clamping nut into the Ethernet cable 3 Insert the sealing insert with claw s ACTI Connecting Vision da Hardware Manual 4 Attach the cable gland body to the hole of the camera Attach to Camera Side Hole Attach to Camera Bottom Hole 5 If the cable will be routed along the surface skip this step If the cable will pass through the surface do the following a Pull the network cable through the bottom conduit hole B b Insert the sealing insert with claw into the cable gland body and then attach the clamping nut to complete the cable solution NOTE Make sure the clamping nut is tightly attached to the cable gland body and the sealing insert is squeezed tightly 6 Proceed with Step 4 Install the Camera to the Surface on page 24 9 ACTI Connecting Vision da Hardware Manual Waterproof Solution with Conduit This section describes the procedures to waterproof the cabling connections using the bundled conduit gland and flexible conduit This is the recommended if an exterior grade Ethernet cable is not available or w
30. y If the cable passes through the surface skip to step 2 Using Flex Conduit Using Naked Cable 2 Connect the network cable to the Ethernet port and other cables if any to the corresponding connectors on the camera Digital Input Output DI DO Connector Audio Input Output Ethernet Port Connector 12V Power Connector 5 pd ACTI Connecting Vision Hardware Manual 3 Connect the other end of the network cable to a switch or injector Then connect the switch or injector to a network or PC and a power source See Power over Ethernet PoE example connection diagram below Ethernet Cable Ethernet Cable Data PoE Injector Power Cable PoE Switch Ethernet Cable Data Power AC Power Source em i Camera In case of using a non PoE switch power up the camera using a power adapter not supplied As needed power up the other connected devices Step 6 Access the Camera Live View See Accessing the Camera on page 40 for more information on how to access the Live View of the camera 2 pd ACTI gt _ Connecting Vision Hardware Manual Step 7 Adjust the Viewing Angle Based on the live view adjust the viewing angle and orientation of the camera Camera Parts Overview Pan Adjustment Screw Rotation Adjustment Screw Tilt Adjustment Screw Tilt Adjustment Screw Adjustment Procedures 1 Loosen the ti
Download Pdf Manuals
Related Search