Philips Wireless surround cinema speakers HTL9100
Contents
1. Basic quality audio 1 Using an analog cable connect the AUX connectors on your SoundBar to the AUDIO OUT connectors on the TV or other device AUX IN AUDIO IN eC 4 Use your SoundBar This section helps you use the SoundBar to play audio from connected devices Before you start e Make the necessary connections described in the quick start guide and the user manual Switch the SoundBar to the correct source for other devices Adjust the volume 1 Press Volume to increase or decrease a volume level e To mute sound press amp Mute e To restore the sound press amp Mute again or press Volume Volume indicator e When you change volume one or multiple Volume indicator up to 8 indicators on the main unit light up to indicate a volume level The more indicators light up the higher the volume level is HDMI OPTICAL ARC 1 HDMI 2 COAX AUX AUDIO IN Bletooth V SURR O O O Q O O O e Ifyou do not press the volume key for five seconds the volume indicators light off and the current source indicator and the sound mode indicator light up Choose your sound This section helps you choose the ideal sound for your video or music EN 11 Surround sound mode Experience an immersive audio experience with surround sound modes 1 Press VSURR to select a surround mode Surround Creates a surround listening experience The V SURR indicator on the main2. indicator blinks white quickly e When the pairing succeeds the indicator lights up white When the pairing fails the indicator blinks white slowly G AC MAINS Connect to the power supply 3 Connect and set up This section helps you connect your SoundBar to a TV and other devices and then set it up For information about the basic connections of your SoundBar and accessories see the quick start guide Note e For identification and supply ratings see the type plate at the back or bottom of the product e Before you make or change any connections make sure that all devices are disconnected from the power outlet Charge speakers If the wireless surround speaker is undocked from the main unit its battery level is indicated by the indicator on the speaker e Light up white full battery e Light up red low battery level less than 30 remaining e Flash red near empty less than 10 remaining 1 Dock your speakers onto the main unit to charge the speakers 2 Turn on the main unit L gt During charging the indicator on the speaker lights up amber EN 7 L gt When fully charged the indicator on the speaker lights up white for 30 seconds Note e lt may take around 2 hours to fully charge the speakers e Ifthe charging lasts more than 4 hours during standby of the main unit the speakers automatically switch to standby Pair up
3. the back or bottom of your product EN 3 2 Your SoundBar Congratulations on your purchase and welcome to Philips To fully benefit from the support that Philips offers register your SoundBar at www philips com welcome Indicators on the main unit This section describes the information of the LED indicators on the main unit HDMI OPTICAL 1 ARC 1 HDMI 2 COAX AUX AUDIO IN Bhetoth V SURR fe Q fe fe fe 10 XIE 4 Volume indicator e When you change volume one or multiple indicators up to eight indicators light up to indicate the volume level Wireless pairing indicators During wireless pairing between the main unit and the surround speakers eight indicators blink one by one e When the pairing succeeds eight indicators light up for three seconds e If the pairing fails eight indicators blink hree times HDMIARC e Lights up when you select HDMI ARC as the input source e Blinks when no audio from the selected HDMI ARC source is detected or when an unsupported audio format is detected G HDMI 1 Lights up when you select HDMI IN 1 as the input source HDMI 2 Lights up when you select HDMI IN 2 as the input source OPTICAL COAX e Lights up when you switch to optical or coaxial input source e Blinks when an unsupported audio format is detected AUX Lights up when you switch to AUX input sour
4. unit lights up Stereo Two channel stereo sound Ideal for listening to music Equalizer Change the high frequency treble and low frequency bass settings of the SoundBar d Press TREBLE or BASS to change the frequency Treble bass indicator When you change frequency levels one or multiple indicator up to 8 indicators on the main unit light up to indicate a frequency level The more indicators light up the more the treble or bass is 4 4 HDMI OPTICAL ARC 1 HDMI 2 COAX AUX AUDIO IN Bletooth V SURR O O O O O O O O Auto volume Turn the auto volume on to keep the volume constant when you switch to a different source It also compresses the sound dynamics increasing the volume for quiet scenes and decreasing the volume for loud scenes 1 Press AUTO VOLUME ON OFF to turn auto volume on or off Ly When auto volume is turned on the V SURR indicator blinks once Ly When auto volume is turned off the V SURR indicator blinks twice 12 EN Synchronize picture and sound If the audio and video are not synchronized delay the audio to match the video d Press AUDIO SYNC to synchronize the audio with the video e AUDIO SYNC increases the sound delay and AUDIO SYNC decreases the sound delay L gt When you change the value of sound delay the more value delay you set the more indicators on the main unit light up Night mode For quiet listening decrease the v
5. with speakers subwoofer The wireless speakers and subwoofer automatically pair up with the SoundBar for wireless connection when you turn on the SoundBar the speakers and the subwoofer If no audio from the wireless speakers and subwoofer can be heard manually pair up the speakers and the subwoofer Pair up with the speakers 1 Turn on the SoundBar and the surround speaker L If the connection to the SoundBar is lost the indicator on the speaker blinks red slowly 2 Press the Connection key on the speaker with a pin to enter the pairing mode L gt The indicator on the speaker blinks red quickly 3 On the remote control press AUX and then press TREBLE BASS and Volume within three seconds L gt If the pairing succeeds the indicator on the speaker lights up white undocked from the main unit or the indicator on the speaker lights up white for 30 seconds being docked into the main unit 8 EN L gt If the pairing fails the indicator on the speaker blinks red slowly If the pairing fails repeat the steps above ui Bw Repeat the steps above to pair up the other surround speaker with the main unit Pair up with the subwoofer 1 Turn on the SoundBar and the subwoofer L gt Ifthe connection to the SoundBar is lost the indicator on the subwoofer blinks white slowly 2 Press the CONNECT button on the subwoofer to enter the pairing mode L gt The indicator on the subwoofer blinks white
6. A device cannot connect with the SoundBar e The device does not support the compatible profiles required for the SoundBar e You have not enabled the Bluetooth function of the device See the user manual of the device on how to enable the function e The device is not correctly connected Connect the device correctly e The SoundBar is already connected with another Bluetooth device Disconnect the connected device then try again Quality of audio play from a connected Bluetooth device is poor e The Bluetooth reception is poor Move the device closer to the SoundBar or remove any obstacle between the device and the SoundBar The connected Bluetooth device connects and disconnects constantly e The Bluetooth reception is poor Move the device closer to the SoundBar or remove any obstacle between the device and the SoundBar e Turn off Wi Fi function on the Bluetooth device to avoid interference e For some Bluetooth the Bluetooth connection can be deactivated automatically to save power This does not indicate any malfunction of the SoundBar PHILIPS sense and simplicity Philips Electronics Australia Limited and Philips New Zealand Limited Warranty against Defects In this warranty We or us means Philips Electronics Australia Limited ACN 008 445 743 or Philips New Zealand Limited Company Number 1723 and our contact details are set out at the end of this warranty You means the purchaser or the origina
7. Always there to help you Register your product and get support at www philips com welcome HTL9100 Coe Question Contact Philips User manual PHILIPS Contents 1 Important Safety Care for your product Care of the environment Help and support w wuwNn N 2 Your SoundBar 4 Indicators on the main unit Remote control Connectors Wireless speakers Wireless subwoofer NOW S a R 3 Connect and set up Charge speakers Pair up with speakers subwoofer Place speakers Connect to TV Connect digital devices through HDMI Connect audio from TV and other devices 0 Oo oO oONN 4 Use your SoundBar 4 Adjust the volume 1 Choose your sound 1 MP3 player 2 Play music via Bluetooth 3 Auto standby 3 Apply factory settings 3 5 Wall mount your SoundBar 4 Wall mount 4 6 Product specifications 4 7 Troubleshooting 5 EN 1 Important Read and understand all instructions before you use your product If damage is caused by failure to follow instructions the warranty does not apply Safety Risk of electric shock or fire lever expose the product and accessories o rain or water Never place liquid containers such as vases near the product f liquids are spilt on or into the product disconnect it from the power outlet immediately Contact Philips Consumer Care to have the product checked before use lever place the product and accessories near naked flames or other heat s
8. On the Bluetooth device switch on Bluetooth search for and select Philips HTL9100 to start connection see the user manual of the Bluetooth device on how to enable Bluetooth L gt During connection the Bluetooth indicator blinks 3 Wait until you hear a beep sound from the SoundBar L gt The Bluetooth indicator lights up L fthe connection fails the Bluetooth indicator blinks continually 4 Select and play audio files or music on your Bluetooth device During play if a call is coming music play is paused Play resumes when the call ends e If music streaming is interrupted place he Bluetooth device closer to the Soundbar 5 To exit Bluetooth select other source e When your switch back to Bluetooth mode Bluetooth connection remains active e The music streaming may be interrupted by obstacles between the device and SoundBar such as wall metallic casing that covers the device or other devices nearby that operate in the same frequency e Ifyou want to connect your SoundBar with another Bluetooth device disable the currently connected Bluetooth device e Philips does not guarantee 100 compatibility with all Bluetooth devices Auto standby When playing media from a connected device the SoundBar automatically switches to standby if no button is pressed for 30 minutes and e no audio video playback is detected from a connected device Apply factory sett
9. audio is automatically played on your SoundBar 1 Using a High Speed HDMI cable connect the HDMI OUT connector on your digital device to the HDMI IN 1 2 on your SoundBar 2 Connect your SoundBar to TV through HDMI OUT ARC e Ifthe TV is not HDMI CEC compliant select the correct video input on your TV 3 On the connected device turn on HDMI CEC operations For details see the user manual of the device Connect audio from TV and other devices Play audio from TV or other devices through your Soundbar speakers Use the best quality connection available on your TV Soundbar and other devices 10 EN Note e When your Soundbar and TV are connected through HDMI ARC an audio connection is not required Option 1 Connect audio through a digital optical cable Best quality audio DIGITAL IN OPTICAL 1 Using an optical cable connect the OPTICAL connector on your SoundBar to the OPTICAL OUT connector on the TV or other device e The digital optical connector might be labeled SPDIF or SPDIF OUT Option 2 Connect audio through a digital coaxial cable Good quality audio DIGITAL IN COAXIAL IN 1 Using a coaxial cable connect the COAXIAL connector on your SoundBar to the COAXIAL DIGITAL OUT connector on the TV or other device e The digital coaxial connector might be labeled DIGITAL AUDIO OUT Option 3 Connect audio through analog audio cables
10. ce AUDIO IN Lights up when you switch to AUDIO IN source 3 5mm jack Bluetooth e Lights up when you switch to Bluetooth mode and Bluetooth devices are paired e Blinks when you switch to Bluetooth mode and Bluetooth devices are not paired V SURR indicator e Lights up when surround mode is selected e Off when stereo mode is selected Blinks once when night mode auto volume is enabled e Blinks twice when Dolby Digital audio is input e Blinks twice when night mode auto volume is disabled e Blinks three times when DTS audio is input Standby On Standby indicator When the SoundBar is in standby the standby indicator turns red Remote control This section includes an overview of the remote control Ce dpticat N taux Bluetooth coax Xs AUDIO IN lt PHILIPS 4 Standby On e Switch the SoundBar on or to standby e When EasyLink is enabled press and hold for at least three seconds to switch all connected HDMI CEC compliant devices to standby HDMI selection HDMI ARC Switch your source to HDMI ARC connection HDMI 1 Switch your source to the HDMI IN 1 connection HDMI 2 Switch your source to the HDMI IN 2 connection GB Source buttons OPTICAL Switch your audio source to the optical connection COAX Switch your audio source to the coaxial connection AUDIO IN Switch your audio source to the AUDIO In connection 3 5mm ja
11. ck AUX Switch your audio source to the AUX connection Bluetooth Switch to Bluetooth mode NIGHT MODE ON OFF Turn night mode on or off Volume control Increase or decrease volume amp Mute or restore volume VSURR Toggle between stereo and virtual surround sound In HDMI in mode connected via HDMI IN 1 or HDMI IN 1 press and hold to switch audio output through the SoundBar speaker or TV speaker BASS Increase or decrease bass O TREBLE Increase or decrease treble AUDIO SYNC Increase or decrease audio delay AUTO VOLUME ON OFF Turn auto volume on or off Connectors This section includes an overview of the connectors available on your SoundBar EN 5 Rear connectors titted oe e Sot 299 OPTICAL COAXIAL R DIGITALIN DIGITALIN upto N AUDOIN Wireless speakers The SoundBar comes with 2 wireless surround speakers left and right O K 20 9 Q AC MAINS Connect to the power supply TO TV HDMI OUT ARC Connect to the HDMI ARC input on the TV HDMI IN 2 Connect to the HDMI output on a digital device HDMI IN Connect to the HDMI output on a digital device DIGITAL IN OPTICAL Connect to an optical audio output on the TV ora digital device DIGITAL IN COAXIAL C
12. clean the product Care of the environment ae Your product is designed and manufactured with high quality materials and components which can be recycled and reused ever dispose of your product with other household waste Please inform yourself about he local rules on the separate collection of electrical and electronic products and batteries The correct disposal of these products helps prevent potentially negative consequences on he environment and human health Your product contains batteries which cannot be disposed of with normal household waste Please inform yourself about the local rules on separate collection of batteries The correct disposal of batteries helps prevent potentially negative consequences on the environment and human health Help and support Philips provides extensive online support Visit our website at www philips com support to e download the user manual and the quick start guide e watch video tutorials available only for selected models e find answers to frequently answered questions FAQs e email us a question e chat with our support representative Follow the instructions on the website to select your language and then enter your product model number Alternatively you can contact Philips Consumer Care in your country Before you contact Philips note down the model number and serial number of your product You can find this information on
13. ep the warranty valid never try to repair the product yourself If you have problems using this product check the following points before you request service If you still have a problem get support at www philips com support Main unit The buttons on the SoundBar do not work Disconnect the SoundBar from the power supply for a few minutes then reconnect Sound No sound from SoundBar speakers e Connect the audio cable from your SoundBar to your TV or other devices However you do not need a separate audio connection when e the SoundBar and TV are connected through HDMI ARC connection or e a device is connected to the HDMI IN connector on your SoundBar e Reset your SoundBar to its factory settings e On the remote control select the correct audio input e Make sure that the SoundBar is not muted No sound from the wireless surround speakers e Wirelessly connect the speakers to the main unit see Pair up with the speakers on page 8 Dock the wireless surround speakers into the main unit to charge the battery EN 15 No sound from the wireless subwoofer e Wirelessly connect the subwoofer to the main unit see Pair up with the subwoofer on page 8 Distorted sound or echo e If you play audio from the TV through the SoundBar make sure that the TV is muted Audio and video are not synchronized e Press AUDIO SYNC to synchronize the audio with the video Bluetooth
14. ings You can reset your SoundBar to the default settings programmed at the factory In AUX mode press and hold NIGHT MODE OFF for 5 seconds L gt When the factory settings restore is complete the SoundBar automatically switches off and restarts EN 13 5 Wall mount your SoundBar Before you mount your SoundBar on the wall read all safety precautions see Safety on page 2 Wall mount e You must detach the surround speakers from the main unit before wall mounting or un mounting e Koninklijke Philips Electronics N V bears no responsibility for improper wall mounting that results in accident injury or damage If you have any query contact Philips Consumer Care in your country e Secure the wall mount to a wall that can support the combined weight of the product and the wall mount Before wall mount you need not remove the four rubber feet at the bottom of the soundbar otherwise the rubber feet cannot be fixed back Screw length diameter Depend on the type of wall mounting this wall mount bracket make sure that you use screws of a suitable length and diameter 3 3 5mm k gt 25mm For information about how to wall your SoundBar see the wall mount guide 14 EN 6 Product specifications Note e Specifications and design are subject to change without notice A
15. l end user of the Goods Supplier means the authorised distributor or retailer of the Goods that sold you the Goods in Australia or New Zealand and Goods means the product or equipment which was accompanied by this warranty and purchased in Australia or New Zealand If you require assistance with the operation of the product its features or specifications please call the Philips Consumer Care Centre on 1300 363 391 in Australia or 0800 658 224 in New Zealand Australia Our Goods come with guarantees that cannot be excluded under the Australian Consumer Law You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage You are also entitled to have the Goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure This is not a complete statement of your legal rights as a consumer New Zealand Our Goods come with guarantees that cannot be excluded under the Consumer Guarantees Act 1993 This guarantee applies in addition to the conditions and guarantees implied by that legislation Additional Warranty In addition to the rights and remedies that you have under the Australian Consumer Law Consumer Guarantees Act of New Zealand or any other applicable law we provide the following warranty against defects 1 If during the first 12 months from their date of purchase from the Supplier Warranty Period the G
16. mplifier e Total output power 210W RMS 0 5 dB 30 THD 168W RMS 0 5 dB 10 THD e Frequency response 20 Hz 20 kHz 3 dB Signal to noise ratio gt 65 dB CCIR A weighted e Input sensitivity e AUX 400 mV e AUDIO IN 220 mV Audio e S PDIF Digital audio input Coaxial IEC 60958 3 Optical TOSLINK Bluetooth e Bluetooth profiles A2DP e Bluetooth version 2 1 EDR Main unit e Power supply 110 240 V 50 60 Hz Power consumption 50 WV Standby power consumption lt 0 5 W e Speaker impedance Woofer 8 ohm e tweeter 8 ohm e Speaker drivers 2 x 63 5 mm 2 5 woofer 2x 25 4 mm 1 tweeter Dimensions WxHxD 1035 x 73 x 156 mm with 2 surround speakers attached e Weight 3 9 kg Surround speakers e Speaker impedance 8 ohm e Speaker drivers 2 x 63 5 mm 2 5 full range Dimensions WxHxD 191 x 73 x 156 mm e Weight 0 7 kg each Subwoofer e Power supply 110 240 V 50 60 Hz Power consumption 30 WV Standby power consumption lt 0 5 W e Impedance 4 ohm e Speaker drivers 1 x 165 mm 6 5 woofer Dimensions WxHxD 200 x 510 x 201 mm e Weight 4 9 kg Wall mount Dimensions WxHxD 40 x 100 x 26 5 mm e Weight 0 1 kg each Remote control batteries e 2x AAA RO3 1 5 V 7 Troubleshooting Warning e Risk of electric shock Never remove the casing of the product To ke
17. ned space Always leave a space of at least four inches around the product for ventilation Ensure curtains or other objects never cover the ventilation slots on the product of contamination Do not mix batteries old and new or carbon and alkaine etc Danger of explosion if batteries are incorrectly replaced Replace only with the same or equivalent type Remove batteries if they are exhausted or if the remote control is not to be used for a long time Batteries contain chemical substances they should be disposed of properly of swallowing batteries The product remote control may contain a coin button type battery which can be swallowed Keep the battery out of reach of children at all times If swallowed the battery can cause serious injury or death Severe internal burns can occur within two hours of ingestion f you suspect that a battery has been swallowed or placed inside any part of the body seek immediate medical attention When you change the batteries always keep all new and used batteries out of reach of children Ensure that the battery compartment is completely secure after you replace the battery e If the battery compartment cannot be completely secured discontinue use of the product Keep out of reach of children and contact the manufacturer This is CLASS I apparatus with double insulation and no protective earth provided Care for your product Use only microfiber cloth to
18. olume of loud sounds when audio is played Night mode is only available for Dolby Digital soundtracks 1 Press NIGHT MODE ON OFF to turn night mode on or off Ly When night mode is turned on the V SURR indicator blinks once Ly When night mode is turned off the V SURR indicator blinks twice Note e If auto volume is set to turned on you cannot enable the night mode MP3 player Connect your MP3 player to play your audio files or music What you need e An MP3 player e A 3 5mm stereo audio cable 1 Using the 3 5mm stereo audio cable connect the MP3 player to the AUDIO IN connector on your SoundBar 2 Press AUDIO IN 3 Press the buttons on the MP3 player to select and play audio files or music e On the MP3 player it is recommended to set the volume in the range of 80 maximum volume Play music via Bluetooth Through Bluetooth connect the SoundBar with your Bluetooth device such as an iPad iPhone iPod touch Android phone or laptop and then you can listen to the audio files stored on the device through your SoundBar speakers What you need e A Bluetooth device which supports Bluetooth profile A2DP and with Bluetooth version as 2 1 EDR e The operational range between the SoundBar and a Bluetooth device is approximately 10 meters 30 feet 1 Press Bluetooth on the remote control to switch the SoundBar to Bluetooth mode L gt The Bluetooth indicator blinks 2
19. onnect to a coaxial audio output on the TV ora digital device AUDIO IN AUX Connect to an analog audio output on the TV or an analog device AUDIO IN Audio input from for example an MP3 player 3 5mm jack EN The illustration above is for the right speaker s top view and bottom view O Speaker indicator e During wireless pairing between the main unit and the speaker the indicator blinks red quickly e When the pairing succeeds the indicator turns into solid white undocked from the main unit or the indicator lights up white 30 seconds hen fades off being docked into the main unit e When the pairing fails or pairing remains undone the indicator blinks red slowly When the speaker is being charged docked into the main unit the indicator lights up amber When the speaker goes to standby the indicator blinks amber Connection key Press with a pin to enter the pairing mode for the speaker G POWER ON Press to turn on the wireless speaker if it automatically goes to standby Wireless subwoofer The SoundBar comes with a wireless subwoofer CONNECT Or O Q Cy 2 AC MAINS M A Q CONNECT Press to to enter the pairing mode for the subwoofer Q Subwoofer indicator e When the power is turned on the indicator lights up During wireless pairing between the subwoofer and the main unit the
20. oods prove defective by reason of improper workmanship or materials and none of your statutory rights or remedies apply we will repair or replace the Goods without charge 2 We do not have to repair or replace the Goods under this Additional Warranty if the Goods have been used for a commercial purpose misused improperly or inappropriately installed operated or repaired abused damaged or not maintained in accordance with the manufacturer s instructions 3 Even when we do not have to repair or replace the Goods we may decide to do so anyway In some cases we may decide to substitute the Goods with a similar alternative product of our choosing All such decisions are at our absolute discretion 4 All such repaired replaced or substituted Goods continue to receive the benefit of this Additional Warranty for the time remaining on the original Warranty Period 5 This Additional Warranty is limited to repair replacement or substitution only As far as the law permits we will not be liable for any loss or damage caused to property or persons arising from any cause whatsoever 6 In order to claim under this Additional Warranty you must telephone us on 1300 363 391 in Australia or 0800 658 224 in New Zealand within the Warranty Period You will be asked for details of the Goods a description of the defect and your personal details Upon accepting your claim we shall assist you with either returning the Goods to the Supplier for replacement
21. or to the most convenient Philips Authorised Service Centre for your Goods to be repaired In some case we may require that you return to the Goods to us at the address below for repair replacement or substitution All returned Goods must be accompanied by satisfactory proof of purchase which clearly indicates the name and address of the Supplier the date and place of purchase and identifies product It is best to provide a legible and unmodified receipt or sales invoice You must bear any expense for return of the Goods or otherwise associated with making your claim under this Additional Warranty 7 This warranty is only valid and enforceable in Australia and New Zealand Contact us or the place of purchase for further details Philips Electronics Australia Limited Philips New Zealand Limited Level 1 65 Epping Rd Level 2 1 Nugent St North Ryde SYDNEY NSW 2113 Grafton AUCKLAND 1023 Consumer Care 1300 363 391 Consumer Care 0800 658 224 E mail pceinfo australia philips com Email pceinfo australia philips com Website www philips com support Website www philips com support August 2011 17 Specifications are subject to change without notice 2013 Koninklijke Philips Electronics N V All rights reserved HTL9100_79_UM_V1 0 PHILIPS
22. ound speakers Place the rear surround speakers to the eft and right side of your seating position either in line with it or slightly behind it 4 SUBWOOFER subwoofer Place the subwoofer at least one meter o the left or right of the TV Leave about 10 centimeter clearance from the wall Dock the surround speakers You can also dock your surround speakers onto the main unit to listen to audio for example watching TV shows and news HDMI OUT ARC 1 Using a High Speed HDMI cable connect the HDMI OUT ARC connector on your SoundBar to the HDMI ARC connector on the TV e The HDMI ARC connector on the TV might be labeled differently For details see the TV user manual 2 On your TV turn on HDMI CEC operations For details see the TV user manual EN 9 Note e If your TV is not HDMI ARC compliant connect an audio cable to hear the TV audio through your SoundBar see Connect audio from TV and other devices on page 10 e If yourTV has a DVI connector you can use an HDMI DVI adapter to connect to TV However some of the features may not be available Connect digital devices through HDMI Connect a digital device such as a set top box DVD Blu ray player or games console to your SoundBar through a single HDMI connection When you connect the devices in this way and play a file or game the e video is automatically displayed on your TV and e
23. ources including direct sunlight ever insert objects into the ventilation slots or other openings on the product Where the mains plug or an appliance coupler is used as the disconnect device the disconnect device shall remain readily operable Disconnect the product from the power outlet before lightning storms When you disconnect the power cord always pull the plug never the cable Risk of short circuit or fire Before you connect the product to the power outlet ensure that the power voltage matches the value printed on the back or bottom of the product Never connect the product to the power outlet if he voltage is different Risk of injury or damage to the SoundBar For wall mountable products use only the supplied wall mount bracket Secure the wall mount to a wall that can support the combined weight of the product and the wall mount Koninklijke Philips Electronics EN Risk Risk Risk V bears no responsibility for improper wall mounting that results in accident injury or damage ever place the product or any objects on power cords or on other electrical equipment f the product is transported in emperatures below 5 C unpack the product and wait until its temperature matches room temperature before connecting it to the power outlet Parts of this product can be made of glass Handle with care to avoid injury and damage of overheating ever install this product in a confi
24. quickly 3 On the remote control press AUX and then press TREBLE BASS and Volume within three seconds L gt If the pairing succeeds the indicator on the subwoofer lights up white L gt If the pairing fails the indicator on the subwoofer blinks white slowly 4 ifthe pairing fails repeat the steps above Place speakers For best sound effect position all the speakers towards the seating position and place them close to your ear level seated e Surround sound depends on factors such as room shape and size type of wall and ceiling windows and reflective surfaces and speaker acoustics Experiment with the speaker positions to find the optimum setting for you _ pl E LI d Connect to TV Connect your SoundBar to a TV You can listen to audio from TV programs through your SoundBar Use the best quality connection available on your SoundBar and TV Connect to TV through HDMI ARC Your SoundBar supports HDMI with Audio Return Channel ARC If your TV is HDMI ARC compliant you can hear the TV audio through your SoundBar by using a single HDMI cable Follow these general guidelines for speakers placement 1 Seating position This is the center of your listening area 2 Place the SoundBar in front of the seating position 3 REARL rear left and REAR R rear right surr
Download Pdf Manuals
Related Search