SYBA SI-PEX40075
Contents
1. Features and Benefits e Compliant with Serial ATA Specification 3 0 Compliant with PCle 2 0 specifications e Supports communication speeds of 6 0 Gbps 3 0 Gbps and 1 5 Gbps e Supports programmable transmitter signal levels Supports Gen 1i Gen 1x Gen 2i Gen 2m Gen 2x and Gen 3i Supports two SATA eSATA ports e Supports AHCI 1 0 and IDE programming interface e Supports Native Command Queuing NCQ e Supports Port Multiplier FIS based switching or command based switching Supports Partial and Slumber Power Management states Supports Hot plug and Hot Swap Compatible with SATA 6G 3G and 1 5G Hard Drives Supports RAID levels 0 1 Bus Interface _ PCi Express x1 Connectors 2x SATA eSATAconnectors System Requirements v PCI Express enabled system with one available PCI Express slot Windows 8 7 32 64 bit Vista 32 64 bit XP Server 2003 2008 Package Contents v 1x PCle SATAIII 6Gb s Card v 1x Driver CD 1x User Manual Note Contents may vary depending on country market Create Raid For more details refer to User Manual in PDF format on the Driver CD e Turn on your computer follow the prompt and press Ctrl M for the RAID setup screen e Use keyboard arrow keys select RAID and press Enter RAID Config will be shown press select Create VD to start creating Virtual Disk Use keyboard arrow keys and lt Space gt to select disks in Free Physical Disks list Selected Disks will b2. e marked with Press Next to proceed configuring Virtual Disks Select RAID Level RAID Mode RAID 0 Stripe or RAID 1 Mirror Select Stripe Size Stripe Block Size 32K 64K or 128K Select Quick Init Quickly erase old data on the hard drives when creating the array Yes or No Select Cache Mode WriteThru or WriteBack e Enter VD Name RAID Array Name for identification e Select Next to finish the configuration setup e Select Yes to confirm Virtual Disk creation e The new array set will be listed under Virtual Disks Press ESC and Y to save and exit Marvell BIOS Setup eo eee Delete a RAID Array Select the RAID Array under Virtual Disks and press lt Enter gt Use keyboard arrow keys lt Space gt and to select VD Select Next and Y Press ESC and Y to save and exit Marvel BIOS Setup Drivers Installation For Windows XP Server 2003 32bit For A New Windows Installation Anew installation requires a floppy disk for the driver installation To make this floppy disk copy the contents of the Marvell 9170 Windows 2003_XP miniport Floppy32 folder found on the driver CD onto a blank floppy disk then follow the directions below 1 After completed the Raid establish follow Microsoft s Windows installation procedure 2 At the Windows Setup screen press F6 to install the driver 3 When prompted press S to specify the location of the driver 4 Insert the floppy disk and then press Enter 5 Scr
3. oll to Marvell shared library install first using the arrow keys and press Enter to select 6 Press S again to select the second device 7 Scroll to Marvell 9170 SATA Controlter 32bit Driver and press Enter to select 8 Press Enter to complete the installation of drivers 9 Continue with the Windows OS installation For An Existing Windows Installation 1 Please insert the driver CD bundled with PCle SATA 6G Card into your CD ROM Drive 2 At the Windows desktop click Start and then Run 3 Type D Marvell 9170 Widows 2003_XP miniport i386 click OK Change D to match your CD ROM drive letter 4 Follow the on screen instructions to complete the installation 5 Restart Windows to complete the installation For Windows XP Server 2003 64bit For A New Windows Installation Anew installation requires a floppy disk for the driver installation To make this floppy disk copy the contents of the Marvel 9170 Windows 2003_XP miniport Fioppy64 folder found on the driver CD onto a blank floppy disk then follow the directions below 1 After completed the Raid establish follow Microsoft s Windows installation procedure 2 At the Windows Setup screen press F6 to install the driver 3 When prompted press S to specify the location of the driver 4 Insert the floppy disk and then press Enter 5 Scroll to Marvell shared iibrary install first using the arrow keys and press Enter to select 6 Press S again to select the sec
4. ond device 7 Scroll to Marvell 9170 SATA Controller 64bit Driver and press Enter to select 8 Press Enter to compiete the installation of drivers 9 Continue with Windows OS installation For An Existing installation 1 Please insert the Driver CD bundled with PCle SATA 6G Card into your CD ROM Drive 2 At the Windows desktop click Start and then Run 3 Type D Marvell 9170 Widows 2003_XP miniport amd64 click OK Change D to match your CD ROM drive letter lt KKS e u SS P a 4 Follow the on screen instructions to complete the installation 5 Restart Windows to complete the installation For Windows 7 Vista 32bit For ANew Windows Installation 1 After completed the Raid establish follow Microsoft s Windows installation procedure 2 At the Windows Setup screen press Load Driver to install the driver 3 Insert the Driver CD bundled with PCle SATA 6G Card into your CD ROM Drive please select Marvell 9170 SATA 6G Controller D Marvell 9170 Win8_7_Vista_Win2008 storport i386 then press Next Change D to match your CD ROM drive letter 4 Continue with Windows OS installation For An Existing Installation 1 Please insert the Driver CD bundled with PCle SATA 6G Card into your CD ROM Drive 2 At the Windows desktop click Start and then Run 3 Type D Marveil 9170 Win8_7_Vista_Win2008 storport i386 click OK Change D to match your D ROM drive letter 4 Follow the on screen instructi
5. ons to complete the installation 5 Restart Windows to complete the installation For Windows 7 x64 Vista x64 For ANew Windows Installation 1 After completed the Raid establish follow Microsoft s Windows installation procedure 2 At the Windows Setup screen press Load Driver to install the RAID driver 3 Insert the Driver CD bundled with PCle SATA 6G Card into your CD ROM Drive please select Marvell 9170 SATA 6G Controller D Marvell 9170 Win8_7_Vista_Win2008 storport amd64 then press Next Change D to match your CD ROM drive letter 4 Continue with Windows OS installation For An Existing Installation _ 4 Please insert the Driver CD bundied with PCle SATA 6G Card into your CD ROM Drive 2 At the Windows desktop click Start and then Run 3 Type D Marvelh 9170 Win8_7_Vista_Win2008 storport amd64 click OK Change D to match your CD ROM drive letter 4 Follow the on screen instructions to complete the installation 5 Restart Windows to complete the installation To Verify Driver Installation 1 Right click My Computer and click Manage 2 Select Device Manager 3 Look for the following Windows XP 2003 Double click SCSI and RAID controller Marvell 91xx SATA 6G RAID Controller should be displayed Windows Vista 7 Double click Storage controllers Marvell 91xx SATA 6G RAID Controller should be displayed
Download Pdf Manuals
Related Search