Home

Kguard AR421-CKT001 Surveillance Combo Kit

1. DVR with Cloud Technology Aurora Series Default user name admin Default password 123456 Preface About this Manual The material in this document is for information purpose and is subject to change without prior notice We made every effort to ensure that this user s manual is accurate and complete However no liability is assumed for any errors and omissions that may have occurred m Z dr I FCC Compliance Statement This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the product and receiver e Connect the product into an outlet on a circuit different from that to which the receiver is connected e Consult
2. Cloud Storage Mode Schedule Motion Detection No of Channel 4 Channels 8 Channels 16 Channels Video Input 4 BNC Inputs 8 BNC Inputs 16 BNC Inputs Video Output 1 VGA 1 BNC 1 HDMI Outputs Video Output Resolution 1024x768 1280x1024 1366x768 1440x900 720p 1080p Audio Input 4 RCA Inputs 8 RCA Inputs 2 RCA Inputs Audio Output 1 RCA Output Video Compression H 264 120fps CIF 352x240 240fps CIF 360x240 480fps CIF 360x240 120fps HD1 704x240 240fps HD1 720x240 240fps HD1 720x240 120fps D1 704x480 240fps D1 720x480 240fps D1 720x480 100fps CIF 352x288 200fps CIF 360x288 400fps CIF 360x288 100fps HD1 704x288 200fps HD1 720x288 192fps HD1 720x288 100fps D1 704x576 200fps D1 720x576 192fps D1 720x576 Frame Rate 120fps WCIF 480x240 240fps WCIF 480x240 480fps WCIF 480x240 120fps WHD1 960x240 88fps WHD1 960x240 176fps WHD1 960x240 120fps WD1 960x480 88fps WD1 960x480 176fps WD1 960x480 960H 100fps WCIF 480x288 200fps WCIF 480x288 400fps WCIF 480x288 100fps WHD1 960x288 72fps WHD1 960x288 144fps WHD1 960x288 100fps WD1 960x576 72fps WD1 960x576 144fps WD1 960x576 Playback Max 4 Channels Max 8 Channels Max 16 Channels Simultaneously Simultaneously Simultaneously Time Channel Event Local Playback Playback Search Playback Mode Play Fast Forward Fast Rewind Slow Motion Zoom General PTZ Control
3. Are you sure that you want to reboot Default Apply Set Auto Maintenance To maintain the operational integrity of the DVR it is recommended to reboot your DVR periodically Similarly to the PC that becomes unstable if left on for a very long time the DVR may become unstable if not rebooted periodically We suggest to reboot the DVR every day To ease to perform periodical reboots you can Set Auto Maintenance to automatically reboot the DVR on a specified schedule When the DVR reboots all settings and data are refreshed from the memory which optimizes the DVR performance In Auto maintain select the frequency to reboot the DVR Options are e Every month Reboots the DVR Maintenance l L Auto maintain Every month on a monthly basis If this option SETTINGS is selected specify the date 1 to Time 00 00 00 l 31 and the time to reboot the DVR Firmware upgrade Reboot e Every week Reboots the DVR on a weekly basis If this option is selected specify the day of the week and the time to reboot the DVR e Every day Reboots the DVR on Default Apply a daily basis If this option is selected specify the time you want to reboot the DVR Note The illustration above is an example of Auto maintain set to Every month The available fields vary depending on the selected Reboot option After all settings are complete click Apply Click Exit to close the current screen E DVR User s Manual Aurora
4. Backup After selecting the log files that you want to backup click to start file backing up process To view the recorded file on the selected date time click ci The playback starts automatically Note e Before backing up the recorded file be sure to plug a USB device into the USB port of the DVR e The log files are saved in TXT format e Do not remove the USB device while file transferring is in progress DVR User s Manual B LI bo A CL 3L l d N e E 9 59 Aurora Series Configuring DVR Settings Ia H C e P R T m ER rr wb Ss FY A da Disk Management A re KEN H D D iA wer i em Eer Formatting HDD Displays the HDD connected to the internal SATA port To make sure that the hard disk drive is properly set it is important to configure the hard disk drive settings before its initial usage Click Format to format the hard disk drive An Are you sure that you want to format this drive Warning message appears on the screen Click Yes to proceed Disk management Status Capacity Total Free Format gt USB Storage Recording 160 0G 154 4G Overwrite by capacity Format Default Apply USB Storage Overwrite Select an overwrite interval options By days Define the beginning date of the files that will be overwritten By capacity Define the capacity limit when the oldest files will be overwr
5. E SATA Port RS485 Built In supports PELCO P amp PELCO D Yes 4 IN 1 OUT 8 IN 1 OUT 4 IN 1 OUT DVR User s Manual a 79 Sensor IN amp Alarm OUT Port Aurora Series Appendix Backup Method HDD USB Network Power Supply 12V 2A Operating Temperature a HDD 10 C to 55 C 14 F to 131 F Storage Temperature Temperature p20 to 70C AF to leen C to 70 C p20 to 70C AF to leen 4 F to 158 F Working Humidity 10 90 Dimension W x D x H 315 x 230 x 40 mm Specifications are subject to change without notice m Z E dr I E DVR User s Manual 80 KGUA RD SECURITY Copyright 2013 All rights reserved Customer Support KGUARD INFORMATION CO LTD USA Technical Support Contact Address 4F No 113 Jian 2nd Road TEL 1 949 450 0052 Jhonghe District New Taipei City 23585 Taiwan Email support kworldcomputer com TEL 886 2 8228 6080 FAX 886 2 8221 6857 Email support kguardsecurity com
6. Ibtain an IP address automatically Use the following IP address IP address Subnet mask Default gateway Use the following DNS server addresses Preferred DNS server Alternate DNS server Don t display this window again xX Cancel WN DVR User s Manual 22 Click Time tab to configure the date and time settings See Date Time on page 33 Click DST tab to configure the Daylight Saving Time settings See DST Daylight Saving Time on page 34 If you are using DHCP connection select Obtain an IP address automatically If you are using Static IP connection select Use the following IP address Specify IP address Subnet mask and Gateway Startup wizard 4 7 LAN PPPoE PPPof Enable User name Password Don t display this window again DDNS amp Port Setup Startup wizard 5 7 MyKguard DDNS Switch Enable Server address www mykguard com Server port 80 Don t display this window again Startup wizard 5 7 MyKguard DDN DDNS Enable Server DYNDNS Host name User name Password Don t display this window again Note If the registered domain name is 123ABC KGUARD ORG the IP address you type on IE or Safari when you browse Web Client is http 123ABC KGUARD ORG User name Enter the DDNS user name Password Enter the DDNS password xX Cancel xX Cancel xX Cancel Aurora Series Getting Started If you are using PPPoE connection s
7. e Connect a USB storage device to the USB port on the back of the DVR e Perform a Record Search see Record Search on page 58 Z note To reduce the video file size use the Trimming Videos on page 58 After selecting the files that you want to backup click Backup A confirmation message appears on the screen Click Backup to continue The Backup Status screen appears Record search ag 213 C Start Ume End time Type Status Su Mo Tu We Th Fr Sa v 09 44 14 09 51 07 Alarm Unlock zee rae l fe GE Alarm Unlock 4 5 6 7 8 9 Alarm Unlock EE 12 I3 1 39 16 a0 ag KEE Alarm Unlock 3B 26 27 28 29 30 Alarm Unlock Backing up the data please wait Alarm Unlock Start time Alarm Unlock End time 23 59 Record type All Search Backup Playback First Prev Next Backt Lock Unlock When backup is complete click OK to close the Backup Status screen EZ note e Before backing up the recorded file be sure to plug a USB device into the USB port of the DVR e Do not remove the USB device while file transferring is in progress I DVR User s Manual 56 Aurora Series Configuring DVR Settings Playing Videos After selecting date time video type and channel click Playback to enter the playback mode interface The selected video file is displayed on the screen Use the on screen calendar to make changes to the dates and control bar to control the video playback ala m O Z TT Curren
8. After all settings are complete click Apply DVR User s Manual Se 45 m Z dr I Aurora Series Configuring DVR Settings e Sensor Schedule Setup Advance Schedule Alarm time period None Sun Add Delete Start time End time 00 00 00 23 59 59 igger tings tings tings tings tings tings tings tings In Schedule click Settings and double click the time slot to set the schedule Start time End time Enter the Start time and End time information when the sensor detection begins and ends To add additional sensor detection schedule click Add To disable sensor detection at the scheduled time check the desired schedule box that you want to delete and click Delete Copy To Copy the current settings to other days Click the arrow to select an option and then click Copy Click OK to save the settings e Sensor Trigger Settings Advance Trigger to Record Snapshot Send E MAIL Alarm output Push Alarm output duration Buzzer Pop up screen Pre record Default WN DVR User s Manual 46 igger tings tings tings tings tings tings tings In Trigger click Settings to configure what actions are taken when the sensor detects an abnormal situation Record Check the box to select the channel s to record when the sensor is triggered Snapshot Check the box to select the channel s to take a snapshot when the sensor is triggered Send E MAIL
9. Check to enable e mail alarm notification If the function is enabled the system will send the alarm messages snapshots snapshot option must be enabled first to the specified e mail address Aurora Series Configuring DVR Settings Note Be sure to complete the E mail and DNS server settings before enabling this function Alarm output If an alarm device is connected check the box to make the device sound the sensor when triggered Push Check the box to enable Push Event function on Mobile Pad when the sensor is triggered EZ note e To use Push Event function you need to do the following ala m O Z TT Enable MyKguard in DVR see MyKguard on page 51 Configure the DVR network connection parameters Download KView QR on your smart phone pad If you are using an iOS portable device you need to enable the Push Event function on app too Alarm output duration Select the alarm sound duration of the alarm device Buzzer Set the buzzer duration when the sensor is triggered Pop up screen Select the corresponding channel will be displayed in full screen when the sensor is triggered Pre record Set the recording period in seconds just before the alarm sensor input before the alarm sensor triggers the recording Post record Set the recording period in seconds after the alarm sensor input after the alarm sensor triggered recording has finished P T Z Check the box to activate cruise of the
10. Ki DVR User s Manual Se 11 Aurora Series Getting Started Step 3 Secure HDD Align the HDD to the holes on the DVR case and secure the HDD using the four 4 supplied screws om Z dr I Step 4 Replace the cover Attach the cover and the screws back in place E DVR User s Manual 12 Aurora Series Getting Started Making Connection Basic Connection ala H m O Z TT 4 Channel 8 Channel DVR Camera Wall outlet Connect the camera cable s to the video input of the DVR via BNC connector D Lo RISK OF ELECTRIC SHOCK Ch Geo DC 12V HDMI IN ki ki Internet Connect a RJ 45 cable from the LAN port on the back of the DVR to an available port ona router or modem Connect a mouse to the USB 2 0 port Monitor To the monitor via VGA connector To the monitor via HDMI connector DVR User s Manual a 13 m Z dr I Aurora Series Getting Started 16 Channel DVR Camera FHI Wall outlet Connect the camera cable s to the video input of the DVR via BNC connector t s ee es eg W r E Wall outlet Wi PC Tablet PC i Mobile Phones Connect a RJ 45 cable from the LAN port on the back of the DVR to an available port ona router or modem Connect a mouse to the USB 2 0 port Monitor To the monitor via VGA connec
11. sticker shown on the DVR Click Exit to close the current screen Display the network information including the network status IP address subnet mask default gateway and other network related information Click the PPPoE tab to view the PPPoE network configuration settings Click Exit to close the current screen Display the online user name IP address log in time and connection status Click Exit to close the current screen Record information DEVICE Resolution Frame rate Quality NETWORK D1 25 Good ONLINE D1 25 Good D1 2 Good Good Good Good Good Good Maintenance Basic Maintenance Auto maintain Never SETTINGS Time Firmware upgrade Reboot Default Aurora Series Configuring DVR Settings Dataper bhour 562MB 562MB 562MB 562MB 281MB 281MB 281MB 281MB Apply Display the specific channel recording settings including video resolution frame rate quality and recording capacity per hour ala m O Z TT Click Exit to close the current screen Configure the automatic system maintenance update the firmware settings or reboot the DVR manually After all settings are complete click Apply DVR User s Manual P 63 E 64 Aurora Series Configuring DVR Settings Manual Reboot Click Reboot to reboot the DVR A message appears click Yes to confirm the operation EI OTI Auto maintain Every month Note Tim
12. 11 1240 30 11 01 12 T2030 11 07 55 THE 13 07 42 TAD 14 33 43 Start time 1308 30 11 01 11 Content Power on Start time 1308 30 11 01 12 End time CH 1 Content MD alarm Start time 1308 30 11 07 55 IP address 10011 217 User name admin Content Remote kam Start time 32820 13 07 42 IP address 10011 217 User name admin Content Remote kam Start time 32820 14 33 43 IP address 10011 217 User name admin Content Remote kam Ri d 1 1 gt Oy DVR User s Manual a T7 m Z dr I Aurora Series Appendix Appendix Troubleshooting If you experience any problems in using the DVR try the following solutions to these common problems before calling for service If problems persist contact the customer service in your area Question The DVR does not turn on and the indicators are not lit Answer e Check ifthe power adapter is properly connected e Plug the power cord to another power outlet the current outlet may be damaged e The power cord may be damaged contact the dealer to purchase a new one Question Some channels have no video signal Answer e Check if the camera is properly connected e Check if the camera is supplied with power e Set the correct video format used in your country NTSC PAL See System Setup on page 33 e The camera cable may be damaged replace with a new one Question have changed the administrator password but cannot remember it Answer e
13. Series Configuring DVR Settings Update System Firmware Maintenance Use this feature to update the firmware with the latest version Download the firmware folder named Auto maintain Every month dvrupgrade and save the folder in a DM USB flash drive Insert the USB flash drive into a USB port of the DVR and click Firmware upgrade to update the firmware wm Are you sure that you want to upgrade A message appears click Yes to confirm the operation Warning Do not turn off the power or unplug from the power supply while updating Default Apply Note After the updating firmware process is complete it is highly recommended to restore the default settings see Load Default Settings on page 66 and then reboot the system Settings Maintenance Use this feature to save the current SSES DVR settings import the configured way settings stored in the USB flash drive EE i or load the system default settings Export settings Export Import settings Import Note Load factory default Settings e Before saving importing the settings be sure to plug a USB device into the USB port of the DVR e The settings file is less than 50KB In Export settings click Export to save the current DVR settings on a USB storage In Import settings click Import to import the DVR settings When data exporting importing is complete click OK to close the current screen Note Do not remove the USB device while file tr
14. a 12 digit hexadecimal code separated by colons Example 00 11 22 33 44 55 Click Apply to save the settings e Editing Account Information Basic User management Basic Authority User name Password Retype password User type Normal Binding Client MAC MAC 00 11 22 33 44 55 Apply Double click the desired account that you want to edit Click the respective item and modify the necessary settings Click Apply to save the settings DVR User s Manual EE j 41 Aurora Series Configuring DVR Settings Basic User management Basic m Z dr I Basic System Advanced Alarm Playback v CH1 e Authorizing Other Users Date Time Network Display Record The administrator can grant access rights to users in the following categories e Basic system data time display record e Advanced Alarm Network COMM PI Z e Playback CH1 CH8 e Backup CH1 CH8 e Remote monitor CH1 CH8 e Disk P T Z control Log Select the check box of the corresponding menu that you want to allow the user to access Click Apply to save the settings Advance Menu Alarm Setup Motion Advance WN DVR User s Manual 42 Sensor Enable Video loss Others Sensitivity Area Settings Settings Settings Settings Settings Settings Settings Settings To CH All Default Schedule Settings Settings Settings Sett
15. connections are tight clean and dry Make sure that you are well insulated to eliminate electric static charge Always wear dry gloves rubber soled shoes or stand on a dry board or platform Always follow recognized safety standards Always wear correct eye ear and body protection Always have second person on site while you work in dark poor ventilation or high places Make sure that you are well protected against arc flashes mechanical injury or other mishaps Make sure that the polarity of wire is correct before installing equipment Always handle equipment with care Do not block the ventilation of equipment Do not put the magnetic parts around the equipment Do not put the objects on top of the equipment DVR User s Manual P 3 ala H m O Z TT Contents um Contents 2 eet gg EEN EE 2 FCC Compliance Statement 2 Sei UE 2 OEY O ee 3 DOGU CTION EE 7 Breet d e TE 7 FE ORIG lt EE 7 Rea FM RE 7 gute EE UE 7 CRA ee 7 ke E let EE 8 FR TOU CONTO E 9 DOS eases ta ge eee vet arenes ea ous arcsec vate E sts nadinterisenamaeerersssteerca 10 GOCE Star EO E 11 installing the Hard Disk EI 11 Making Conneccion ecse E E EEE 13 BEE EIERE 13 4 Channel 8 Channel DVR EE 13 TEC NREL Eeer 14 Connecting to EE eege 15 4 Channel 8 Channel e EE 15 TC VS VIR ee 16 Easy NetWork SETUD nein inne ne ana eee E ee ee nee ee 17 Basic Connection for Remote Live View on Smart Phone bad 17 Basic Connection for Re
16. function with resolutions HD1 D1 WHD1 the resolutions are copied only to channels CH1 CH4 After all settings are complete click Apply Schedule Bit rate SYSTEM Manual Normal Alarm DATE TIME TE ER TE DISPLAY All Copy Default Apply The schedule that is displayed on screen applies only to one channel at a time There are three types of recording modes to choose from Manual The recording is done manually To start recording you need to click on recording button Jon Task Bar or press the Record button on remote control See Remote Control on page 9 or Task Bar on page 26 Normal The DVR will continuously record for any period where Normal mode is selected Note Make sure the space on hard disk is sufficient when using constant recording Alarm The DVR will only record when an alarm is detected To know more on alarm settings and events please see Alarm Setup on page 42 CH Select the channel you want to set the schedule Copy CH To CH Copy the current settings to all channels or one specific channel Click the arrow to select an option and then click Copy After all settings are complete click Apply DVR User s Manual a 39 Aurora Series Configuring DVR Settings e Recording Schedule Setup e Feie Schedule SYSTEM Mon Add BAGG DATE TIME Start time End time Type DISPLAY 00 22 00 23 59 59 Alarm Detault
17. l 6zchannelonly Basic SIEB D VA Information Network estatus nlinelusers Record Seales DVR User s Manual Se 31 m Z dr I Aurora Series Configuring DVR Settings Click WER to enter the Main menu Menu Basic Z3 R Select one of the menu options and configure the necessary settings SES DDR Basic menu Configure the system date time display record and user settings Advance menu Configure alarm network internet application and PTZ settings Record Search menu Search the recorded video Log Search menu Search the recorded videos Disk Management menu Display the HD USB storage status and format the device Information menu Display the system network user and video settings information Maintenance menu Update the firmware export import the system settings and restore the default settings of the DVR Logout Exit the menu I DVR User s Manual 32 SIC Menu ue ye VN System Setup System Device name DATE TIME Device ID DISPLAY Video format VGA resolution 1024 x 768 Language English Logout time Never Startup wizard On Default Apply Aurora Series Configuring DVR Settings Device name Enter the desired name for the DVR The name can be composed of alphanumeric characters and is used to identify this device in your list of activated DDNS accounts Device ID Enter the desi
18. message appears click Yes to confirm the operation e Configuring Other Users Basic User management Basic Authority User name Password Retype password User type Normal Binding Client MAC MAC 00 11 22 33 44 55 Apply Aurora Series Configuring DVR Settings In Basic user menu you can specify the user name password MAC address and allow the binding client MAC or not User name Select a name for the user you want to define The best usernames are short and relevant to the speciality of the user they re intended for Password Can be composed of numbers from 0 to 9 and letters The maximum length is 16 characters Retype password Must exactly match with the password for the specific user User type The Administrator type is binded directly to the administrator account The user type for all other users is Normal Binding Client MAC Media Access Control When this feature is enabled then the DVR can authenticate the client PC by the MAC address in combinition with the specific DVR user name For example the user of the DVR is kguard and the binding MAC address is 00 11 22 33 44 55 Therefore only the PC with MAC address 00 11 22 33 44 55 and logged in user kguard can remotely connect to the DVR via Web Client program MAC Client device s MAC address allows the DVR to identify the connecting device during the remote session The MAC address should be entered as
19. settings Refer to DDNS on page 52 e Select the E MAIL tab to configure the email setup Refer to E mail on page 52 e Select the Cloud tab to configure the cloud storage settings Refer to Cloud on page 54 e Select the UPnP tab to activate the UPnP function Refer to UPnP on page 53 System Manage Configure the DVR general settings including disk management PTZ speed dome system maintenance options and other related settings System Manage e Select the Disk management tab to configure the hard disk drive Refer to HDD on page 60 e Select the P T Z tab to customize the PTZ camera settings Refer to PTZ Setup on page 55 e Select the System tab to configure the DVR name device ID and video format Refer to System Setup on page 33 e Select the Maintenance tab to configure the automatic system maintenance load factory defaults update the firmware settings or reboot the DVR manually Refer to Maintenance on page 63 E DVR User s Manual 76 Local Settings Aurora Series Web Client Specify the local path directory to save downloaded videos files and snapshots Local Settings ala H mr O Z TT Set the recording length for each video file 5 10 15 30 minutes and click the corresponding Browse button to modify the path Click Apply to save the settings Log Search and backup the log Refer to Log Search on page 59 Date Time 1408 30 11 01
20. should be the same rating as the factory Always keep cables and connectors in good condition Improper or worn electrical connections can cause short circuits and can increase the chance of an electrical shock Do not use worn damaged or bare cables Always avoid open circuit voltage The added voltages increase the severity of electric shock hazard Always wear insulated gloves while you adjust equipment Electric power should be turned off and insulated gloves should be worn when making any equipment adjustment to assure shock protection Always wear protective clothing such as long sleeve shirts while you are installing or removing equipment Preface AN Caution The lighting flash with an arrow head symbol in an equilateral triangle is intended to alert the user There is dangerous voltage presence near by the product s enclosure which may be risk of person Always wear high snug fitting shoes Always wear clean clothes without grease or oil Protect neighboring workers from exposure to arc radiation Always wear long trousers or jeans while you are installing or removing equipment Always wear safety helmet or hard head and safety shoes before work Always keep the equipment in dry places Always wear safety harnesses belt while you work in high places Always wear dry clothing and avoid moisture and water Always wear Public Safety Vest while you work at night Make sure all electrical
21. time e Date Enter the Start Time and End Time information by entering the starting ending date and time From To Enter the Start Time and End Time information when the DST begins and ends at your location Display Setup Display Margins Auto sequence Main output SYSTEM Name Mask Color Time Name DATE TIME CH1 Settings Settings Settings N CH2 Settings Settings Settings CH3 Settings Settings Settings CH4 Settings Settings Settings CH5 Settings Settings Settings CH6 Settings Settings Settings CH7 Settings Settings Settings Settings Settings Settings To CH All Copy Default Apply E DVR User s Manual 34 Name Enter your desired channel title to be displayed on the screen Mask You can create and shape a privacy zone mask which hides part of the image on the selected channel To do so select Settings and enter the Mask submenu See Privacy Zone Settings on page 35 Color Adjust image hue brightness contrast and saturation settings Select Settings enter the Color submenu See Color Settings on page 35 Aurora Series Configuring DVR Settings Time Name Choose to hide or display the recording data time date or channel during recording See Overlay Settings on page 36 Copy CH To CH Select to copy the current settings to all channels or one specific channel Click the arrow to select an option and then click Copy ala H mr O Z TT After all settings are compl
22. to view the move the current position icon to quickly scan through footage full screen Then left mouse click on the areaon video events the footage that needs to be enlarged The area will be enlarged in full screen Right mouse click to scale down DVR User s Manual P 57 Aurora Series Configuring DVR Settings om Z dr I Playback Screen Hide Time Line Playback Screen Hide Time Line and Control Bar Trimming Videos ay A E Su Mo Tu We Th Ffr s a ta iS 5 67 686 9 BB 213 4 D 1617 i9 WM 21 22 23 mM 2 FW 23 2 5 Bi To mark the start and end trimming time during playback in full screen do the following e Drag the slider to where you would like to start trimming and click the EW icon gt G 7 8 FS 213 MS 16 1 19 21 22 23M oxy wR gt 7 8 amp B 12 13 14 15 16 17 19 DM 21 22 23 nyn 26 2 mm 5 a ea EE 6 L 12 13 14 15 16 19 D 21 22 23 S62 z w SCD User s Manual 58 Aurora Series Configuring DVR Settings To save the trimmed video click the icon Select the file that you want to save and check the Backup box Backup Name Type Status Capacity Total Free Backup Manage USB Storage OK 4 0G 4 0G v Manage Type Start time End time Alarm 2013 08 29 09 57 39 2013 08 29 10 05 19 Alarm 2013 08 29 10 06 13 2013 08 29 10 28 34 Alarm 2013 08 29 10 29 26 2013 08 29 10 48 23 Size Request Prev Delete Backup Then click Backup to save the f
23. you want to delete and click Delete Copy To Copy the current settings to other days Click the arrow to select an option and then click Copy Click OK to save the settings e Motion Trigger Settings About Motion Detection In general the motion detection can be used with almost all static and wired cameras However PTZ systems are incompatible with motion detection avoid allowing motion detection on a channel which has a PTZ system connected to it False Triggers It is very important to set the motion detection on a suitable sensitivity level If you set the motion detection at a high sensitivity levels 4 or lower then the frequency of false alarm events increases Vice versa if the sensitivity level is too low 20 or higher you might increase the risk that an important motion event will not trigger the motion detection to record Therefore during the DVR system configuration it is advised to check the motion detection in normal and low light conditions during the day and night Also false triggers may be caused by severe weather conditions for example lightening and heavy rain To minimize the false triggers do the following e Adjust the Image Settings to configure the brightness and contrast see Color Settings on page 35 e Make limitations to the motion sensitive areas selecting only the area where the target would most probably be Hence turn off the motion sensitivity to any area a target cannot move In T
24. 0 After all settings are complete click Apply If you cannot use the either of the two default ports 80 or 9000 the specified port may be occupied by other programs or it is being blocked by your service provider Enter other port number In this case you need to add the port number after the IP address For example if you set the Web port as 85 you need to enter the IP address as 192 168 3 103 85 WN DVR User s Manual 50 Sub stream Advance ALARM PPPoE Port Sub stream Enable Resolution Frame rate Oualttv Good Good Good Good Good Good Good Good All Copy Default Apply Aurora Series Configuring DVR Settings N The sub stream is the video stream that the DVR will send to remote oO devices via a network or the Internet z It is the lower quality stream as a G reduction in video size using constant bit rate and thus making it easier to send over a network Enable Click to use sub stream for network transfer Resolution How many pixels compose the image Choose between the following two options CIF and QCIF The CIF resolution is 352 x 240 pixels in size It is suggested to use by higher end systems for remote Internet viewing for multiple cameras uses a lot of bandwidth QCIF resolution is 176 x 120 pixels in size and is one quarter the size of CIF resolution It is advised to use for remote viewing from portable devices example cell pho
25. 44 Copy CH To CH Copy the current settings to all channels or one specific channel Click the arrow to select an option and then click Copy After all settings are complete click Apply e Set Motion Detection Area In Area click Settings and specify the area for motion detection alarm By default the whole screen is marked for motion detection green block e To disable motion detection on i an area click the grid cursor and then drag the mouse to highlight anil 2 the scope to unmark the area Pa e Right click to close the setup screen E note To avoid getting false triggers it is recommended to set the motion detection area at an appropriate location such as door window etc DVR User s Manual Se 43 Aurora Series Configuring DVR Settings e Motion Schedule Setup Prior defining the motion schedule Schedule make sure the channel you want to Alarm time period None associate it with is Enabled Sun Add Delete Advance m Z dr I gger In Schedule click Settings and double aun Start time ea tings click the time slot to set the schedule Mon tan Lee ti er VOOU 12 00 00 a Start time End time Enter the Start ings Wed time and End time information when tings i Thu the motion detection begins and ends tings ae To add additional schedule click Add tings To disable motion detection at the tings scheduled time check the desired schedule box that
26. Click OK to save the settings User Setup SYSTEM User name User type DATE TIME admin Administrator user E DISPLAY Normal RECORD Add user User SYSTEM User name User type DATE TIME Note DISPLAY RECORD Are you sure to delete the user Add user E DVR User s Manual Alarm 70 22 opy Apply Binding Client MAC Unlimited Unlimited Delete user Binding Client MAC E nlimited nlimited Delete user You can also double click the time slot to set the recording mode and schedule Start time End time Enter the Start time and End time information when the recording begins and ends Type Select the recording mode To add additional recording schedule click Add To delete a recording schedule check the desired schedule box that you want to delete and click Delete In User menu you can define and configure the various levels of access different users have to the DVR system By default there is one administrator account The administrator account s user name is admin and the password is 123456 Note e We highly recommend you to change the password to protect your privacy e f the password is left blank then the connection via portable device smart phone pad to the DVR will not be established To configure other users click Add user To delete the specific user check the user box that you want to delete and click Delete user A
27. Click to exit the Web Client Adjust the volume level Manage the display window Switch live view to sub stream mode Switch live view to main stream mode Enable disable digital zoom Open close all channels for viewing Start stop manual recording Capture a snapshot Switching Screen Modes The Live screen can be viewed in different modes Click the respective icon on the task bar to switch to different display mode Preset K y Za Cruise line Cuse e e Aua 1 Color a o Preset Cruise line ee 4 CR Color cf Click Wo switch to 8 split Window mode Aurora Series Web Client ala m O Z TT 2 08 19 2013 15 0 ia WU em 2 f i Hi mode Preset KE v Za Cruise line ee 4 ra Color o Preset Cruise line Cruise v D Color Click to switch to 9 split Window mode DVR User s Manual Aurora Series Web Client Video Playback Click Playback tab remotely search play and download recorded videos m Z dr I Searching and Playing Videos Configure the search options see Search on page 55 Su Mo Tu We Th Fr p obs ale take zb 111 12 13 14 15 16 18 19 20 21 22 23 25 26 27 28 25 30 08 00 14 00 16 00 18 00 Click to switch between Manage the Record List and Search Result Page Adjust the volume level display window Click the respective icon to control the video playb
28. N z e RRE 60 Be ET 60 Formatting BK CREMER 60 Managing USB Disk EE 61 eSATA 16 channel DVR E A 61 Oa O EE 62 Mile 62 PSO escent nt knees ae te eins scene wa cers eh cee A E aceeineesacaseeeanuneane 62 ONING ec rw ert eens ee ite eect ee ean go etaee setts eaten areca ene wees eseeeneeetece 62 REEL eee ener ee ee ee 63 DEENEN 63 E E e 63 VEITH Nee EE 64 SE Ze NET iC E 64 LTS EWEN 65 DVR User s Manual Se 5 Contents aa Sal 65 Z Load Default Settings enone nn etme eee nna nce ene EE a 66 2 LOC OUT er a N A E E T E 66 E Wep CHEM E 67 PC VO UA BEE 67 Interiace TE 68 Switching le e 69 vidco POYDA Korrea a AN EAE A E EAN 70 Searching and Playing EIERE 70 Downloading Recorded Videos EE 71 CONTEE S E earar A AE EEE AAA A 72 ARILO ARETE LTIS EEEE P ETETA A ET TIE E A EE A T 72 Date TAS rererere EEE SEE EEEE RNE EEE EEEE OEN 73 ROCOTO WE 74 Kee 74 E gn E 75 V ie g ees caec ance En E EE EEE EAE OE E 75 Eege 76 System En EE 76 Beien le 77 OG E EE E AE E E E 71 APPNO EE 78 Ueeiflel gelen E 78 BS COINS snc pea sai stcee a nysgn E E ENAA N 79 I DVR User s Manual 6 Aurora Series Introduction Introduction ala H m O Z TT Product Overview Front Panel e E a a Gee O HD LINK POWER gt OK OQ a og EN E A cu C amp D Homi 1 Menu Press to enter the menu 5 IR receiver Receives incoming remote control commands 2 Esc Press to exit the current menu 6 HDD LED Lights bl
29. PTZ camera on the specified channel when the sensor is triggered Click OK to save the settings Video Loss CES Video loss is regarded as a potential alarm event and is considered to occur any time that the DVR does not Enable Trigger receive an active signal on any of its NETWORK 7 Settings inputs COMM Settings The default behavior of the DVR 3 Settings when a channel has no incoming Settings video signal is simply to display Settings Video Loss in light blue text on a Settings black background over the associated Settings channel If you re not using all the Settings inputs on your DVR then some SE All ee channels will be in constant Video Loss state Make sure that you don t Enable a video loss action for these channels Motion Sensor P T Z Default Apply Enable Click to activate video loss monitoring function Trigger Configure the actions to be taken when the DVR does not receive any video input signal from the connected camera s The settings configuration is similar to Sensor Trigger See Sensor Trigger Settings on page 47 Copy CH To CH Copy the current settings to all channels or one specific channel Click the arrow to select an option and then click Copy After all settings are complete click Apply DVR User s Manual a 47 Aurora Series Configuring DVR Settings Others ee Customize the event s alarm settings Motion Sensor Video loss others Disk error
30. Select Enable to trigger the alarm if the DVR has trouble to access Disk error Enable or detect the hard disk drive Disk full Enable Disk full Select Enable to trigger the alarm when the hard disk drive is full Trigger Settings IP address conflict Select Enable to IP address conflict Enable trigger the alarm if the DVR has detect another device on the same network using the same IP address Trigger Settings Trigger Configure the actions to be taken when the event type occurs See Event Trigger Settings on page 49 Default Apply After all settings are complete click Apply e Event Trigger Settings Advance In Trigger click Settings to configure the actions to be taken when the event type occurs Send E MAIL Check to enable e mail alarm notification If the function is enabled the system will send the alarm messages to the specified e mail address Trigger to Record Snapshot Send E MAIL Alarm output Push Alarm output duration Buzzer 0 Note Pop up screen No Be sure to complete the E mail and Pre record DNS server settings before enabling Default this function Alarm output If an alarm device is connected check the box to make the device sound the alarm when triggered Push Check the box to enable Push Event function on Mobile Pad when the event type occurs Note e To use Push Event function you need to do the following Enable MyKguard in DVR see MyKguard on
31. To obtain the factory default password contact your retailer or directly send an email to KGUARD at support kguardsecurity com Question The remote control is not working Answer e Make sure nothing is blocking the remote control and the DVR sensor Aim the remote control at a proper distance e Check the remote control batteries Question cannot control the PTZ camera Answer e Make sure the protocol baud rate address code and other settings on the camera match the settings you have configured on the DVR See PTZ Setup on page 55 e Check if the cables are properly connected Question am getting too many email alerts Answer e Check if the Sending Interval setting for the email alerts See E mail on page 52 e If the DVR keep reporting errors such as Video Loss or HDD error check if the camera is properly connected or other hardware configurations Question cannot access the web client Answer e Check if the network cable is properly connected to the DVR e Check if the network settings are properly configured See LAN on page 49 e Ensure that you have Internet Explorer 6 or above Question The buzzer keeps on sounding Answer e Check the alarm settings Motion Detection or Video Loss may be detected Check the HDD capacity and the video connections which may be triggering the alarm I DVR User s Manual 78 Aurora Series Appendix Specifications ala H m O Z TT
32. ack Capture a snapshot Enable disable digital zoom 4 split Window Display Click the zoom icons to zoom in or zoom out the TE Tem Pz time line 5 6 7 8 9 12 13 14 15 16 19 20 20 122 253 26 2728 35 30 Record list gt gt gt UU RW aa It SI e E eB k el amp E E DVR User s Manual 70 Aurora Series Web Client Downloading Recorded Videos ala H m O Z TT EE ME Wo Tu h Fr Ss 1 2 3 12 13 14 15 W 17 ID 2 41 2 ZA 24 TEENE Page 1 1 Click to download the video to your Select the box of the local hard disk See Local Settings files that you want to on page 77 for details on setting download download path folder Click to switch between Record List and Search Result Page DVR User s Manual a 71 om Z dr I Aurora Series Web Client Configure Settings Click Configure tab to remotely configure the DVR Main menu Menu option setting F Information System V Device name DateTime Device ID Display Firmware wersion i 1 EE on ome 3 The available menu options and setting configurations are very similar to the DVR system menu E note The relevant page reference for additional information is listed on each menu item Information View the DVR information including the device name and ID serial number firmware version and MAC address System WN DVR User s Manual 12 Aurora Series Web Clien
33. again to recognize the changes After all settings are complete click Apply I DVR User s Manual 54 Aurora Series Configuring DVR Settings PTZ Setup Here you can configure the DVR to be able to operate PTZ devices PTZ stands for Pan Tilt amp Zoom Advance ALARM CH Enabl Protocol Baud rat Addr l kaua Se GE salaire The DVR is compatible with many NETWORK Pelco D 2400 H i but not all PTZ devices available For Ka 2 Pelco D 2400 2 f f COMM ae more information please consult the 3 Pelco D 2400 3 vendor Pelco D 2400 Geleet 2400 5 Customize the PTZ camera settings Gelee D 7400 e after the PTZ speed dome is properly zem installed via RS 485 connection Pelco D 2400 S Enable Check the channel box which To CH All fore the PTZ camera is connected to Default Apply Protocol A protocol is like a common language that the DVR uses to communicate to the PTZ device Make sure this setting matches the requirements of your device Baud rate Check the PTZ camera documentation to get to know this parameter Address Specify the command address of the PTZ camera that you want to associate with the selected channel Copy CH To CH Copy the current settings to all channels or one specific channel Click the arrow to select an option and then click Copy After all settings are complete click Apply Note Do not use motion detection function on the PTZ camera to avoid wrong motion interpretati
34. ansferring is in progress Click Exit to close the current screen DVR User s Manual B AR L gt L em T a EN 65 m Z dr I Aurora Series Configuring DVR Settings Load Default Settings Use this feature to restore the factory default settings of the DVR Load factory default System v Date Time In Load factory default settings click Display Record Settings to load the default settings ees Mi User Check the respective setting option Alarm Network box that you wa nt to restore COMM Ji P T Z TIP Men e To restore all settings click All e To deselect all checked boxes click Clear After all settings are complete click Apply Apply Logout Click to log out of the system A message appears click Yes to confirm the operation The Main menu will be locked after you log out You need to enter the user name and password before entering the Main menu Menu x Logout Are you sure that you want to log out E DVR User s Manual 66 Aurora Series Web Client Web Client Use Web Client to remotely access the DVR at anytime ala H m O Z TT Before accessing Web Client for first time e Ensure that the Network settings of the DVR is properly configured See LAN on page 49 e Your computer has a web browser such as Internet Explorer or Safari installed e UPnP is configured in the DVR and Router or the port
35. channel layout and dwell time settings e Click X to remove the selected settings Aurora Series Configuring DVR Settings Mode Allows to configure how many channels are displayed on the screen The available options include 1 x 1 one channel in full screen 2 x 2 four channels 3 x 3 nine channels 4 x 4 sixteen channels depending on the number of DVR channels Layout Allows to configure in what order the channels appear on the screen depending on the chosen Mode Dwell Allows to configure how long the channels are displayed on the screen in an auto sequence mode The available period is from 1s 300s Display SYSTEM Auto sequence DATE TIME z sequence 1 gt Main Output DENEN SYS s e UE Mam output SE DATE TIME Margins Margins Main output Stencil1 x1 5 To custom Default Apply Auto sequence Default Dwell Copy Copy the selected auto sequence type setting to Custom setting Click Copy to copy the settings EZ note This function will overwrite the original customized settings If you wish to use customized pattern while the customized settings have been applied then do not use Copy function Click Apply to save the settings This menu allows you to configure the number and order of the channels displayed on the split window Main output The available options include 1 x 1 one channel in full screen 2 x 2 four channels 3 x 3 nine
36. channels 4 x 4 sixteen channels 6 split 8 split 10 split 13 split depending on the number of DVR channels Then click on the channel name and select from the drop down menu the desired channel you wish to be displayed Click Apply to save the settings ala m O Z TT DVR User s Manual P 37 Aurora Series Configuring DVR Settings Record Setup Basic Set the audio function and recording mode for each channel Bit rate Schedule SYSTEM Enable Check to enable or uncheck Enabl Audi Mod nable BS Saz to disable the record mode for a channel DATE TIME S Always DISPLAY S Always gie 3 z eg Audio Check to enable the audio rue recording for a channel Uncheck to anny disable this option Always Note This function requires a camera with the audio support or an All Copy external microphone Default Apply Always Always Mode Select the type of recording mode There are two types of recording modes available Always and Schedule Always The DVR will continuously record for any period where Always mode is selected Note Make sure the space on hard disk is sufficient when using constant recording Schedule The recording is performed according to a pre defined schedule To define the schedule see Schedule on page 39 Copy CH To CH Copy the current settings to all channels or one specific channel Click the arrow to select an option and then click Copy A
37. ck the direction arrow to select the direction of the PTZ camera For the other function settings see below Increase the iris level Delete the selected Increase the preset Increase the focus speed brightness level P T Z Set a preset point Nee E To set a specific preset point wiper function 1 Select the desired S Channel Reduce the Je E Ka Clean 2 Click the direction iris level Nei teat arrow to select the Cruise line direction of the PTZ Reduce the 3 ZZ camera focus speed sf b start stop 3 Select a preset point Zoom out se number Cruise settings Go to a specific preset point OO ee ee SERRER Add or delete cruise Start stop cruise of line 2 Note the PTZ camera These settings are only applicable if a PTZ soeed dome is properly installed on DVR via RS 485 connection Click to start stop manual recording DVR User s Manual a 29 Aurora Series Operating the DVR gt Click to open the video playback screen m Z dr I Select the desired time slot that you want to play To play in full screen click a channel See Playing Videos on page 57 for more details E DVR User s Manual 30 Aurora Series Configuring DVR Settings Configuring DVR Settings ala m O Z TT Main Menu System DEJAS DIRE RITA User Alarm IONES Network COMM JS 7 N Record Search Log Search Hlald DIS EMEC SEI USB Storage SSA
38. clude a date time and camera name on a video stream per M Time Name Le channel T CH In Time Date click Settings and select the channel that you want to set the overlay si settings Time overlay To include the date time and or channel name on the recorded file check the Name overlay Default Margin Display Margins SYSTEM Margin top DATE TIME Margin bottom Margin left Margin right Auto Sequence Display Margins SYSTEM Auto sequence DATE TIME m Sequence al al d Stencil1 x1 NM DVR User s Manual 36 respective box Click Apply to save the settings Auto sequence Main output Default Apply Auto sequence Main output Custom Mode To custom Default Dwell 10S 35 When the DVR is connected to a monitor you can define the image size and position to be displayed on the screen Drag the slider bar to adjust the top bottom left and right margin setting Click Apply to save the settings When auto sequence mode is activated see Task Bar on page 26 the DVR will automatically cycle through all available channels displaying each in turn expanded to fill the entire screen The channels can be displayed on the screen stencil or customized pattern Auto sequence Select the auto sequence type To customize the auto sequence order select Custom and do the following e Click to configure the new display setting including the display mode
39. duction Mouse The DVR is supplied with a USB mouse that you can use to operate the DVR Simply plug in the supplied mouse into the USB mouse connector at the rear panel of the device m Z dr I Mouse Operation Double click the Left button Double click the live image of any channel for full screen display Double click the left button again to return to the window display of all cameras Drag an area line In motion mode use this function to select motion area In Color Setup menu mode it will adjust color control bar E DVR User s Manual 10 Aurora Series Getting Started Getting Started ala m O Z DI Installing the Hard Disk Drive Depending on the package you have purchased the hard disk drive may be included in the full package If it is not pre installed follow the installation instructions on this user manual Lg DO NOT install or remove the hard disk drive while the device power is turned on The DVR supports one 3 5 SATA hard disk drive To install the HDD follow the steps below Note The illustrations below show an 8 channel DVR same procedures apply to a 4 16 channel DVR Step 1 Remove the cover a Loosen the screws in the left right and rear sides as shown Step 2 Install HDD Connect the data and power cables to the hard disk drive HDD and place the HDD on the DVR case o Se ere ze Zil aS vi Sr Dire peste Seite oP deel
40. e interval options By days Define the beginning date of the files that will be overwritten By capacity Define the capacity limit when the oldest files will be overwritten Never The recording will stop when the hard disk is full When you click Save the system will automatically save all settings Click OK gt Close to exit the Setup Wizard 2 note To prevent the Wizard Setup screen appears every time the system reboots set the Startup wizard setting to Off in Basic menu See System Setup on page 33 Aurora Series Operating the DVR Operating the DVR Logging in Enter the user name and password before entering the Main menu E note The default user name and password are User name admin Password 123456 DEVICE ID 0 USER NAME admin PASSWORD Main Screen Once you turn on the DVR the live view screen appears 2 note The number of channels displayed may vary depending on the DVR model The illustration below is from a 8 channel DVR ae ed A j 5 VA We k d T Fy i Motion detection is activated Recording is in progress Task bar ala H mr O Z TT DVR User s Manual P 25 Aurora Series Operating the DVR Task Bar To open the task bar do one of the following e Right click on any place on the screen e Press the Menu button on the remote control om Z m dr I To access the Main menu or other common function
41. elect PPPoE tab Specify User name and Password See LAN on page 49 for further OO more Information To enable remote live view the DVR via MyKguard you need to enable the function first prior accessing MyKguard http w Note For accessing MyKguard it is advised to use Internet Explorer 8 or above Switch Select Enable to enable this function DDNS Dynamic DNS is a service that registers a domain name and the floating IP address with a DDNS server so that the domain name can be routed to the IP address even if the IP is changed in a dynamic IP system DDNS Select Enable to enable this function Server Select the DDNS server Host Name Enter the domain name you registered on DDNS server DVR User s Manual B CZE ef IC gd Sa D te e GZ e Par J E E IN AI Le 23 m Z E dr I Aurora Series Getting Started HDD Setup tartup wizard 6 7 status apacity Total Free Recording 154 6G 148 5G Overwrite by capacity Don t display this window again Completing the Setup Wizard tartup wizard 7 7 Startup Finished Please turn off the Startup Wizard in the Basic Menu I DVR User s Manual 24 Format Format xX Cancel ard setup JS Close Display the HDD status and capacity To format the HDD check the Format box and click Format Overwrite Select an overwrit
42. ete click Apply e Privacy Zone Settings Defining a privacy zone in the channel allows to block a portion of the channel with a black box To add a privacy zone in Mask click Settings and select the channel that you want to set the privacy Drag the mouse to frame an area on the screen that you want to mask The black box indicates the area for masking You can set up to 4 mask Clear Apply areas Click Apply to save the settings e Color Settings In Color menu you can configure the brightness contrast hue and saturation settings per channel Color CH Brightness BRI Defines how bright the image appears on the display BRI Contrast CON Increases the difference between the darkest black and the con Ya whitest white in the image Modify the contrast if the sections of the image grey out E note Setting the contrast parameter too high will degrade the image quality Hue Changes the color mix of the image Default Apply Saturation SAT Alters how much color is displayed in the image The highest the saturation the brighter and vivid colors will appear to be Setting this parameter too high can degrade the image quality 2 Note All the changes to the image color settings affect your recordings Click Apply to save the settings DVR User s Manual Se 35 Aurora Series Configuring DVR Settings aes e Overlay Settings 5 Use these settings to in
43. etting Started Easy Network Setup The outstanding feature of this DVR is that you do not need to do any complicated network settings to set up the DVR for remote live view on smart phone pad web browsers MyKguard or uploading images to Cloud ala H m O Z TT In a DHCP typical personal home LAN Local Area Network basic steps are as below Basic Connection for Remote Live View on Smart Phone Pad Step 1 Connect the DVR to network a Connect the power adapter to the DVR See Making Connection on page 13 b Connect a RJ 45 cable from the LAN port on the back of the DVR to an available port on a router Step 2 Install APP Download KViewQR application on your smart phone pad Step 3 Add connected DVR and view Live screen Add the connected DVR by scanning the QR code Once the router provides IP address to DVR the Live screen appears Basic Connection for Remote Live View on MyKguard Step 1 Connect the DVR to network a Connect the power adapter to the DVR See Making Connection on page 13 b Connect a RJ 45 cable from the LAN port on the back of the DVR to an available port on a router DVR User s Manual a 17 om Z dr T Aurora Series Getting Started Step 2 Login to MyKguard Open your computer IE browser IE8 or above and enter http www mykguard com in the URL box Enter the DVR ID and password on Quick Login Then click Login 2 note DVR ID can be found at the fol
44. forwarding is completed in the Router PC login Open your computer web browser and enter the DVR IP address or domain name in the URL box Don t know the IP Address of your DVR The IP address of the DVR vary depending on the network settings you configured in NETWORK menu see LAN on page 49 If your network type is DHCP ask your network administrator for the IP address assigned to the DVR If your network type is PPPoE ask your Internet Service Provider ISP for the IP address assigned to the DVR If your network type is Static IP check the IP address you configured for IP address in LAN menu If the DVR is connected to a DDNS check the Domain Name that you configured when you created the DDNS account and type the domain name in the URL box ll S http 10 0 100 187 loc A DVR LOGIN Then enter the login name and password Click gt to login note The default DVR user name and password are User name admin Password 123456 DVR User s Manual a 67 m Z dr I Aurora Series Web Client Interface Overview After you login to Web Client the Live screen appears 2 note The number of channels displayed may vary depending on the DVR model The illustration below is from a 8 channel DVR Manage the PTZ speed dome see page 29 WW UE AS NENAS Cruise line use TEORA Manage the display color settings see page 28 BE DVR User s Manual 68
45. fter all settings are complete click Apply Bit rate The bit rate section allows you to configure the actual amount of data that the DVR will use to record a Bit rate Schedule SYSTEM Resolution Frame rate Quality video The parameters that can be DATE TIME D1 25 Good configured is video resolution frame Pe E z5 Good rate and quality settings for each 25 Good channel E Goon Resolution The two types of record a SE modes are as follows D1 CIF HD1 e EES D1 960H WCIF WHD1 WD1 The 25 Good resolutions CIF WCIF WD1 960H 25 Good can be selected only to channel 5 or Toc All Corr higher channel Default Apply WN DVR User s Manual 38 E note If the record mode setting is set to 960H it is recommended to use a 600 TVL or higher resolution camera Frame rate Select how many images per second the DVR will record According to the standard Real time is 30fps NTSC or 25fps PAL With the resolution WD1 960H the recommended frame rate with 8 channels is 8fps and with 16 channel is 6fps Aurora Series Configuring DVR Settings ala m O Z TT Quality Select the video quality Best means the lowest compression rate but larger video file size Normal means the highest compression rate and smaller video file size Copy CH To CH Copy the current settings to all channels or one specific channel Click the arrow to select an option and then click Copy If you use the Copy All
46. ick to format the external hard disk drive An Are you sure that you want to format this drive Warning message appears on the screen Click Yes to proceed Note Do not remove the external HDD while drive formatting is in progress Manage Click to view or delete file s stored in the external hard disk drive DVR User s Manual B lt D I ed NGLIS EI 61 Aurora Series Configuring DVR Settings Device Information Device Device name NETWORK Devic e ID ONLINE Serial NO Firmware version R E Ce R D M AC DVR ID Network Information LAN PPPoE Network status IP address LAN ONLINE Subnet mask Default gateway RESSAR Preferred DNS server Alternate DNS server IP address conflict IP address WAN Media port Web port Online Information Inline users DEVICE User name IP address NETWORK RECORD DVR User s Manual D98027C7009945378411 T20130912 84 1091284 00 99 45 37 84 11 DFM98NPYCS5SVP8N6GMZY Connected 10 0 100 187 255 255 0 0 10 0 0 254 10 0 0 251 0 0 0 0 No IP conflict 203 67 242 140 9000 80 Login time Disconnect Display the DVR information including the device name and ID serial number firmware version MAC address and DVR ID The device information is mainly used by the technical support in the event that you require assistance Note The DVR ID represents the QR code
47. ile into the selected USB drive Note e Before backing up the recorded file be sure to plug a USB device into the USB port of the DVR e Do not remove the USB device while file transferring is in progress Log Search The Log Search displays a list of events presented in chronological Date Time Content Playback Type All order the most recent events will be 2013 08 29 09 44 15 Power on l di Start time 2013 08 29 at the end of the list 2013 08 29 09 44 14 MD alarm 00 00 00 Log search The Log will list all events that the DVR monitored 2013 08 29 09 51 13 Power off me End time 2013 08 29 2013 08 29 09 52 00 Power on a 23 59 59 Type Select the log type The available options are all alarm Detail operation All will include in the result both alarm and operation events 2013 08 29 09 51 59 MD alarm Search Backup Clear 2013 08 29 09 52 44 Local login 2013 08 29 09 53 28 Modify display settings 2013 08 29 09 56 45 Reboot RH ei 2013 08 29 09 56 56 Power off gt eset rows el Start time End time Specify the Start Time and End Time to filter the list 2013 08 29 09 57 39 Power on First Prev Next Last Search After selecting date time and log type click to search for recorded files The search results are displayed on the right window First Prev Next Last Click to browse the search result page by page Clear Click to delete the log file A pop out message appears click Yes to confirm file deletion
48. ings Settings Settings Settings Settings Copy Apply Trigger Settings Settings Settings Settings Settings Settings Settings Settings About Motion Detection The DVR detects the motion by comparing one frame with the next A sufficient previously defined amount of difference is interpreted as motion As a result the DVR is able to detect when there is a change in the picture and initiate the recording Aurora Series Configuring DVR Settings EZ note e It is advised to avoid using wireless cameras with any of the motion recording equipment The wireless technology is sensitive to interference and therefore common issues like static and image distortion might trigger the motion detection unintentionally e It is recommended to set the sensitivity level at the moderate level so that the DVR only record the particular scene when motion is detected If it is set at the highest level the DVR may record continuously e Do not use PTZ system and motion detection function at the same time to avoid wrong motion interpretation T 2 l QO Z Lu Area Select the area for motion detection alarm See Set Motion Detection Area on page 43 Schedule Motion detection is triggered only based on the start and end time described in the schedule See Motion Schedule Setup on page 44 Trigger Configure the actions to be taken when motion is detected See Motion Trigger Settings on page
49. ion will be uploaded and stored automatically at Dropbox WN DVR User s Manual 20 Aurora Series Getting Started Setup Wizard The Setup Wizard will appear the first time you start the DVR It will guide you to configure initial DVR settings including time setup network setup and other basic settings ala m O Z TT startup wizard 1 7 H 264DVR Welcome to the setup wizard xX Cancel Follow the on screen instructions to complete the initial setup E note To skip and disable Startup Wizard check the Don t display this window again box and click Cancel Enter Administrator Password User name By default the administrator user name is set to startup wizard 2 7 Admin User name admin Password Old password Default is Old Password 123456 We suggest you change the New Password password to protect your privacy Retype password E Note If the password is left blank then the connection via portable device smart phone pad to the DVR will not be established Don t display this window again DVR User s Manual a 21 m Z dr I Aurora Series Getting Started Basic Setup startup wizard 3 7 09 23 201 11 41 10 Date Time Date format MM DD YYYY Time format 24 Hour Time zone GMT 08 00 Taipei Auto update Time server time windows com Don t display this window again x Cancel Network Setup amp Testing tartup wizard 4 7 PPPolk
50. itten Never The recording will stop when the hard disk is full After all settings are complete click Apply View and configure the USB storage device connected to the USB port on back panel Disk management USB Storage Status Capacity Total Free OK 4 0G 4 0G Format Manage USB Storage Status Capacity Total Free OK Note x pa Manage Are you sure that you want to format this drive i DVR User s Manual 60 Click Format to format the USB disk drive An Are you sure that you want to format this drive Warning message appears on the screen Click Yes to proceed Note Do not remove the USB device while drive formatting is in progress Aurora Series Configuring DVR Settings Managing USB Disk Drive Manage Click Manage to view or delete file s EE stored in the USB disk drive To delete folder s file s check the respective box es and click Delete An Are you sure that you want to delete the file Warning message appears on the screen Click Yes to proceed All File name Size KB RecordFiles ar log Note Are you sure to delete the file Note Do not remove the USB device while file deletion is in progress eSATA 16 channel DVR only Disk management Use eSATA connection for backup een purposes HDD e Status Capacity Total Free Note ye USB Storari None OM OM e TEE The eSATA disk drive cannot be regen used for direct recording Format Cl
51. l day and time Note Be sure that the DVR network connection and DNS server address are properly configured before proceeding with the e mail setup Enable Select Enable to activate the e mail notification function Aurora Series Configuring DVR Settings Sending interval Select an e mail sending interval Mail server SMTP Enter the SMTP Server of the sending e mail server If you do not know the SMTP mail server address please consult with the e mail service provider or check the information on their web page Port Enter the SMTP port of the sending e mail server 2 note By default the SMTP port is 25 for e mail without SSL verification For Gmail server or for e mail that needs SSL Verification the SMTP port is 465 by default Check with your ISP for the correct setting ala m O Z TT Connection security If your e mail server needs the SSL Secure Sockets Layer or TLS Transport Layer Security verification select SSL TLS Check with your e mail service provider for the applicable setting User name Enter the e mail address of the sender Password Enter the password of the sender s e mail To Enter the e mail address where the notification e mail is to be sent CC Enter the e mail address that you want to copy to You can set up to 4 e mail addresses Test Click to send a test e mail to the recipient s e mail address After all settings are complete click Apply UPnP UPnP Uni
52. loud storage activation link Server switch Select Default and click Active Cloud directly EZ note If the Server switch setting is set to Customer you need to complete the following settings before clicking Active Cloud Mail server SMTP Enter the SMTP Server of the sending e mail server If you do not know the SMTP mail server address please consult with the e mail service provider or check the information on their web page Port Enter the SMTP port of the sending e mail server Connection security If your e mail server needs the SSL or TLS verification select SSL TLS Check with your e mail service provider for the applicable setting User name Enter the e mail address of the sender Password Enter the password of the sender s e mail Active Cloud Click to activate the function An activation e mail will be sent to the Receiver e mail account E note e An e mail will be sent to the Receiver e mail account after clicking ActiveCloud You must check your e mail and follow the link to complete cloud storage activation within 3 minutes e A QR code also appears on the screen after clicking Active Cloud Using your smart phone pad simply scan the QR code and confirm the link to activate the Dropbox cloud storage Prior scanning the QR code with the smart phone pad you need to download the Kview QR application e Every time the cloud storage account is changed or HDD is formatted you must activate the account
53. lowing 1 On the DVR QR Code sticker 2 In DVR menu Click MER gt Information gt Device gt DVR ID Quick Login Use your device ID and the device password to log in and secure your home or business Device ID Alias a Log in MyKGUARD Use your username and password to log in and secure your home or business SS ee Log In Home Products Support Contact us When using this function make sure MyKguard is enabled prior accessing MyKguard In DVR menu Click WER gt Advance gt COMM gt MyKguard Step 3 View Live View WN DVR User s Manual 18 Aurora Series Getting Started Basic Connection for Uploading Images to Cloud Step 1 Connect the DVR to network a Connect the power adapter to the DVR See Making Connection on page 13 ala m O Z TT b Connect a RJ 45 cable from the LAN port on the back of the DVR to an available port on a router Step 2 Set Cloud Storage In Main menu select Advance gt COMM gt Cloud and type an email account to receive the cloud storage activation link See Cloud on page 54 Advance MyKguard DDNS E MAIL UPnP Enable Interval 1min Motion detection Enable CH SERGE Receiver Server switch Default Mail server SMTP Port Default Apply Step 3 Activate Cloud Storage There are two ways to activate cloud storage a Via e mail An e mail will be sent to the Receiver e mail account after clicking ActiveCloud You mu
54. m device Buzzer Set the buzzer duration when the motion is detected Pop up screen Select the corresponding channel will be displayed in full screen when the motion is detected Pre record Set the recording period in seconds just before the motion triggers recording Post record Set the recording period in seconds after the motion triggered recording has finished P T Z Check the box to activate cruise of the PTZ camera on the specified channel when the motion is detected Click OK to save the settings Sensor Rr Customize the sensor settings Motion Video loss Others Enable Click to enable sensor alarm Enable Type Name Schedule Trigger Type Select the sensor type between NETWORK N C Sensor1 Settings Settings N O Normal Open and N C Normal COMM 2 ae Sensor2 Settings Settings cl ose Seit Settings Settings Please check the documentation of P T Z mee See sensora Settings Settings sensors to learn the correct value to Sensor5 Settings Settings use Sensor6 Settings Settings consely SSES settii Name Specify the sensor name Sensor8 Settings Settings Schedule Set the sensor detection To CH All Copy schedule See Sensor Schedule Default Apply Setup On page 46 Trigger Configure the actions to be taken when sensor is triggered See Sensor Trigger Settings on page 46 Copy CH To CH Copy the current settings to all channels or one specific channel Click the arrow to select an option and then click Copy
55. mote Live View ON Mvkeuargd 17 Basic Connection for Uploading Images to Cloud 19 UP N N BE 21 Enter Administrator E EE 21 NG UU EE 22 Network Setup amp all C1 9 gy Janene en ee er ee ee ee eee 22 DONS POC Et EE 23 MDD SS CUD ieaeetnvae onteentencnccsesiaratpenaniyceswa A ate enone S 24 Completing the Setup Wizard E 24 Operanne TMS DVR EE 25 LOC TINE Weeer EE EE EE E A T E T Ei 25 Man S eE Mil E 25 TKE E 26 Configuring DVR Settings ccccccscsssscscsccccscsccccsceccccsceccccscescccscecescscecescscscesens 31 Main Men WE 31 Bae MONU NEE 33 SVEM oC U eire eE AEE TE EE 33 Dare Tine SOE IG ME 33 YS TNS ee E E E 33 DST Daylieht Saving TIME J ccase ce ssectrstysantnosessccecnnntacneia aieatsosaesatesse tosaeacteteensasconen 34 BE DVR User s Manual 4 Contents Kee EE 34 BYES e 34 T IVAN eT a EE 36 PATO Ee TE CS aa E aunene rs ep iqeracsnrasmeeacs 36 2 MAOO eege 37 Kee E EU o EE 38 Ke 38 de E 38 SCS UN hee 39 BSE D EE 40 AV noe Tee 42 Ee un SU a DE 42 NOUO EE 42 ee ee 45 VACO Ee een A asa voene eatin vareneaneasanedusentoheniceesteenscesgecueas 47 BA eebe 48 lee 49 PPPOE eebe 50 Aale EE 50 SOS Gl SA E 51 Beigl le On E 51 VU ASAU EN 51 DONS eee E E antes oes emaeenqesanceeaneere et aaee esas 52 EAA E E A E E A E A E E E E EE 52 UPRP geet 53 E 0 E 54 PZ SOD D 55 SS lte EE 55 Record SC DE 55 Backin le Re 56 PPV UI te Te E 57 TOUTS e e EE 58 Reegele EE 59 IVS Bae EE 60 MOD WEE 60 FO
56. ne Frame rate The number of frames per second fps that the DVR will record The recommended fps is 10 Quality Select the video stream quality Copy CH To CH Copy the current settings to all channels or one specific channel Click the arrow to select an option and then click Copy After all settings are complete click Apply Communication Setup MyKguard Advance ALARM NETWORK Server address MyKguard DIDIN E MAIL Cloud Switch Enable Server address www mykguard com Server port 80 Default Apply Display MyKguard server address Server port Display the server port number Switch To enable remote live view the DVR via MyKguard you need to enable the function first prior accessing MyKguard http www mykguard com Note e For viewing DVR live view using MyKguard does not require to configure the port forwarding in router e For accessing MyKguard it is advised to use Internet Explorer 8 or above web browser e For remote live view from a single DVR use Quick Login For remote live view from multiple DVRs use Log in MyKGUARD See Basic Connection for Remote Live View on MyKguard on page 17 LJ pag e ek Ze DVR User s Manual J j 51 E Aurora Series Configuring DVR Settings DDNS Advance MyKguard DDNS E MAIL UPnP Cloud DDNS Enable Server KGUARD ORG Host name User name Password Default Apply Note To use this feat
57. nects to a Speed dome camera sensor or alarm device via RS 485 5 USB 2 0 Connects to a USB mouse or flash disk 12 eSATA Connects to an external hard drive 6 LAN Connects to a network via RJ 45 7 Audio Output Connects to a speaker via RCA WI DVR User s Manual 8 Aurora Series Introduction Remote Control ala H m O Z TT 1 Login Lock Press to login lock the main menu 13 Press to decrease the volume level 2 Numeric keys 1 0 Press to display channel 1 16 14 Record Press to start manual recording 3 Display mode Press to switch to different display 15 Stop Press to stop manual recording mode 4 Menu Press to enter the menu 16 Extra Reserved key 5 PTZ Press to configure PTZ settings 17 Rewind Press to rewind during video playback 6 Exit Press to exit the menu 18 Play Press to play recorded video 7 OK Press to enter the selected menu item and 19 Fast forward Press to fast forward during video confirm the setting playback 8 Up Press to move up in the OSD menu 20 Slow play Press to playback video at reduced speed 9 Left Press to move left in the OSD menu 21 Pause Press to pause the video playback 10 Right Press to move right in the OSD menu 22 Audio In Playback mode press to turn the audio on 11 Down Press to move down in the OSD menu 23 Mute Press to mute audio 12 Press to increase the volume level DVR User s Manual P 9 Aurora Series Intro
58. nsor tab to customize the sensor alarm settings Refer to Sensor on page 45 e Select the Video loss tab to customize the video loss alarm settings Refer to Video Loss on page 47 e Select the Others tab to customize the event s alarm settings Refer to Others on page 48 Network Configure the basic network settings Netarork O Obtain an IF address automatically a Use the following IP address IP address Default gateway O Obtain DNS server address automaticalhy Prefened ONS server Altemate DNS server e Select the LAN tab to configure the basic network settings Refer to LAN on page 49 e Select the PPPoE tab to Configure the basic network settings using PPPoE Refer to PPPoE on page 50 e Select the Port tab to specify the Client Port and HTTP Port numbers Refer to Port on page 50 e Select the Sub stream tab to customize the video stream settings of a particular channel if the channel is being viewed via remote access Refer to Sub stream on page 51 DVR User s Manual a 75 Aurora Series Web Client COMM Configure Internet related application settings EZ note Be sure that the DVR network connection is properly configured before proceeding with the folllowing setup m Z E dr I COMM DU e Select the MyKguard tab to enable remote access the DVR via MyKguard Refer to MyKguard on page 51 e Select the DDNS tab to configure the domain server
59. on Search Record Search The Record Search allows you to search the recordings saved on the storage The search can be performed based on start time end time record type and channel All recordings that match the search criteria are displayed on the screen Record search ag 213 C Start time End time Type Status Select date Su Mo Tu We Th Fr Sa 09 44 14 09 51 07 Alarm Unlock E E2 Wi 09 51 59 09 56 45 Alarm Unlock 4 5 6 ie 8 Bi S inp SH 09 57 37 10 05 19 Alarm Unlock Ee 12 1a aS ES 16 he ig 19 0 21 2 23 10 06 13 10 28 34 Alarm Unlock 5 27 28 B 3 10 29 26 14 42 38 Alarm Unlock Select time 14 43 32 14 47 16 Alarm Unlock Start time ee 14 48 08 17 18 39 Alarm Unlock End time 23 59 59 Select video type Record type All Select the box of Ma1 m2 M3 E the files that you want to backup Select channel lock unlock Search Backup Playback First Prev Next Last Backup Lock Unlock DVR User s Manual P om Z dr I Aurora Series Configuring DVR Settings Search After selecting date time video type and channel click to search for recorded files The search results are displayed on the right window First Prev Next Last Click to browse the search result page by page Lock After selecting Unlock recorded files click to lock the files The locked files cannot be overwritten Unlock After selecting Lock recorded files click to unlock the files Backing up Videos To backup files
60. page 51 Configure the DVR network connection parameters Download KView QR on your smart phone pad If you are using an iOS portable device you need to enable the Push Event function on app too Alarm output duration Select the alarm sound duration of the alarm device Buzzer Set the buzzer duration when the event type occurs P T Z Check the box to activate cruise of the PTZ camera on the specified channel when the event type occurs Click OK to save the settings D DVR User s Manual LAN To access the DVR over local area network you need to configure the LAN parameters of your DVR Prior configuring the LAN interface confirm the type of internet connection you are using and the related network connection parameters with your Internet Service Provider ISP or network administrator to complete the setup Advance ALARM PPPoE Port Sub stream Obtain an IP address automatically Use the following IP address IP address 010 000 100 187 Subnet mask 255 255 000 000 De f au t g atewa y 0 al 0 F 0 0 0 d 0 0 0 F 54 Use the following DNS server addresses Preferred DNS server 010 000 000 251 000 000 000 000 Alternate DNS server Default Apply Aurora Series Configuring DVR Settings connection network ala mr O Z TT Obtain an IP address automatically Select if you are using DHCP With Dynamic Host Configuration Protocol DHCP service your router will a
61. r damage arising out of combining the system with the devices of a third party e Any claim or action for damages brought by any person or organization being a photogenic subject due to violation of privacy with the result of pictures from a surveillance camera including saved data for some reason becomes public or is used for the purpose other than for surveillance WN DVR User s Manual 2 Safety Information AN Warning This is the symbol for indicating any potential hazard risk or condition requiring special attention The user needs to refer to the important operating and maintenance or servicing instructions Safety Precautions Do not touch live electrical parts Electric shock can be avoided Follow the recommended practices listed below Faulty installation improper grounding and incorrect operation and maintenance of electrical equipment are always sources of danger Do not try to install equipment outdoor during strong wind and rain Do not install or remove equipment outdoor when raining Do not try to install or operate any equipment during a thunderstorm Always ground all electrical equipment and the work platform Prevent accidental electrical shocks Connect power source control cabinets and work platform to an approved electrical ground Always use the correct cable size Sustained overloading will cause cable failure and result in possible electrical shock or fire hazard Work cable
62. red DNS server address Alternate DNS server Specify the backup DNS server address Backup DNS server address is used when the preferred DNS server is not accessible EZ Note e Please contact your local ISP Internet Service Provider to obtain the correct DNS Server parameter e f you want to use the E mail notification Preferred DNS server settings must be properly configured After all settings are complete click Apply DVR User s Manual a 49 m Z E dr I Aurora Series Configuring DVR Settings PPPoE Advance Sub stream ALARM PPPoE Enable User name Password Default Apply After all settings are complete click Apply Port Advance Sub stream ALARM Media port Web port Default Apply 2 note Select if you are using PPPoE connection With PPPoE Point to Point Protocol over Ethernet your DVR is most likely connected to a DSL modem and your ISP has supplied you with an authentication user name and password to the Internet PPPoE Select Enable to use PPPoE network connection User name Enter the user name that your ISP has supplied you Password Enter the password that your ISP has supplied you Specify the Media Port and Web Port numbers Media port Is used to access your DVR via portable device The default port number is 9000 Web port Is used to access your DVR from your local LAN or the Internet using a laptop or PC The default port number is 8
63. red ID for the DVR The device ID identifying the DVR can only be composed of numbers and cannot be the same with other IDs when multiple DVRs are connected in the same network Video format Choose between NTSC and PAL depending on your geographical location Note NTSC for the USA Canada Mexico Japan Korea and some other regions PAL for UK Europe Australia and some other areas VGA resolution Select how many pixels the DVR will output It is recommended to use as high resolution as possible that matches with your monitor s highest resolution Language Select the language you wish the menu items to be displayed in Logout time Select the time period for menu time out Startup wizard The Setup Wizard will run automatically the first time you start the DVR The wizard will guide you through all the basic settings you need to configure for getting your DVR start up and functioning Note To prevent the Wizard Setup screen appear every time the system reboots set the setting to Off Date Time Setup Date Time Date Time Date Time Date format MM DD YYYY DISPLAY Time format 24 Hour RECORD Time zone GMT 08 00 Taipei Auto update Time server time windows com 08 19 2013 15 10 07 Default Apply Date Time All video footages are stored on the HDD based on their time stamps Make sure you set the correct system date and time Note You can click on on screen calendar Us H or t
64. rigger click Settings to configure the actions to be taken when motion is detected Advance Trigger to Record Sen PET Record Check the box to select the i Alle channel s to record when the motion SE tings is detected Alarm output ae Push S Snapshot Check the box to select the ings Alarm output duration Se channel s to take a snapshot when Buzzer ae the motion is detected Pop up screen vg Send E MAIL Check to enable e mail Pre record 0 alarm notification If the function is tings enabled the system will send the alarm messages snapshots snapshot option must be enabled first to the specified e mail address Default I DVR User s Manual 44 Aurora Series Configuring DVR Settings 2 note Be sure to complete the E mail and DNS server settings before enabling this function Alarm output If an alarm device is connected check the box to make the device sound the alarm when motion is detected ala m O Z DI Push Check the box to enable Push Event function on Mobile Pad when the motion is detected E note To use Push Event function you need to do the following Enable MyKguard in DVR see MyKguard on page 51 Configure the DVR network connection parameters Download KView QR on your smart phone pad If you are using an iOS portable device you need to enable the Push Event function on app too Alarm output duration Select the alarm sound duration of the I O alar
65. s click the respective icon LB Click to enter the Main menu See Main Menu on page 31 fica Click and select the desired channel to be displayed in full screen 4 Jt I DVR User s Manual 26 Aurora Series Operating the DVR fica Click to switch to 4 window display T 2 l CO Z Lu UR an oa i F Paf y a ete LP DVR User s Manual a 27 Aurora Series Operating the DVR cl Click to switch to 9 window display MN AN om Z m dr I a Click to start stop rotation of channel display To customize the auto sequence order see Auto Sequence on page 36 A Click to access the Color Setup menu Color CH d P con HUE E Default Apply To adjust image hue brightness contrast and saturation settings select the channel and drag the slider bar to adjust the color item setting Click Apply to save the settings Click to enlarge certain area on the screen Click and drag the left mouse button to frame an area on the screen that you want to zoom in Zoom area sn de The selected location will be enlarged and displayed as full screen WN DVR User s Manual 28 Aurora Series Operating the DVR eh Click to access the Volume Control bar ala m O Z TT Drag the slider to adjust the volume level Click D to turn mute on or off e Click to access the PTZ Control panel e Select the desired channel e Cli
66. st check your e mail and follow the link to complete cloud storage activation within 3 minutes Open your email and click Activate Cloud Follow the on screen instructions to complete the cloud account activation DVR User s Manual Se 19 Aurora Series Getting Started amp Testing E mail File Edit View Tools Message Help 8t fF ww Te xiOo OO vw Reply Reply Al Forward Print Delete Previous Next Addresses From xxxx mail com Date Wednesday June 05 2013 9 46 AM To xxxx mail com Subject Testing E mail JOEPIE KGUARD SECURITY Hi Dear Please click on the following link to complete your setup for Cloud Storage at Dropbox Activate Cloud The snapshot taken at set interval or by motion detection will be sent and stored automatically at Dropbox where you can easily access to and share the snapshot with others Your KGUARD Team b Via scanning QR code A QR code also appears on the screen after clicking ActiveCloud Advance MyKguard DDNS E MAIL UPnP ALARM Receiver NETWORK p Note Serv Activation was successful Default Apply Using your smart phone pad simply scan the QR code and confirm the link to activate the Dropbox cloud storage Note Prior scanning the QR code with the smart phone pad you need to download the Kview QR application Step 4 View Snapshots After the account activation is complete the snapshot taken at the preset time interval or by motion detect
67. t Date Time Configure the date time and daylight saving time settings ala H mr O Z TT Time Settings time Windows com e Select the Date Time tab to configure the date and time settings Refer to Date Time on page 33 e Select the DST tab to configure the daylight saving time settings Refer to DST Daylight Saving Time on page 34 Display Customize how channels are displayed on the monitor screen Display Settings e Select the Display Settings tab to configure the display settings Refer to Display on page 34 e Select the Auto sequence tab to configure the order of how the channels appear when auto sequence function is activated Refer to Auto Sequence on page 36 DVR User s Manual a 73 Aurora Series Web Client Record Customize the recording settings and schedule Refer to Record Setup on page 38 om Z S dr Record Settings User Change the password and authorize users and set the access rights in using the DVR Refer to User Setup on page 40 IP address Login time 10 0 11 212 SOEN ER e BE DVR User s Manual 74 Aurora Series Web Client Alarm Customize the motion sensor video loss and other event s recording settings ala H mr O Z TT Alarm Settings copy cH C och bt Dit e Select the Motion tab to customize the motion recording settings Refer to Motion on page 42 e Select the Se
68. t position Trim footage Save footage Hide time line and control bar Zoom in Zoom gt 12 Hide time line out time line LU 12 13 M D 16 18 19 D 2 22 23 Exit playback 5 26 3 Rewind pause play frame by frame Volume play slow play fast forward Zoom in footage EES Zoom in Zoom out time line Increase or decrease the Mute Mute the playback time line display Volume Alters the output volume of playback Rewind Reverses the footage Exit playback Leaves the playback interface and returns Pause Play Pauses the footage or plays the footage at to live viewing mode normal speed ae Ea l Hide time line Maximizes the area on screen for playing Frame by frame play Press multiple times to play back your footage by hiding time line footage fram by frame Hide time line and control panel Maximizes the area on Slow play Plays back footage at reduced speed Press screen for playing back your footage by hiding time line multiple times to further reduce the speed 1 2 speed and control panel 1 4 speed 1 8th speed Trim and Save footage Used to mark a Start Time and Fast forward Plays back footage at accelerated speed End Time for the selection and save the selection See Press multiple times to further accelerate the speed x2 Trimming Videos on page 62 speed x4 speed x8 speed Current position A basic progress meter You can click to Zoom in footage Left mouse click once
69. the dealer or an experienced radio TV technician for help Declaration of Conformity This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference 2 This device must accept any interference received including interference that may cause undesired operation Copyright Limitation of Liability e This publication is provided AS IS without warranty of any kind either expressed or implied including but not limited to the implied warranties of merchantability fitness for any particular purpose or non infringement of a third party s rights e This publication may include technical inaccuracies or typographical errors Changes may be made to the information herein at any time for publication improvements and or of the corresponding device s Disclaimer of Warranty In no event shall the supplier be liable to any party or any person except for replacement or reasonable maintenance of the product for the cases including but not limited to the following e Any damage or loss including but without limitation direct or indirect special consequential or exemplary arising out of or relating to the device e Personal injury or any damage caused by inapppropriate use or negligent operation of the user e Unauthorized disassemble repear or modification of the device by the user e Any problem consequential inconvenience or loss o
70. tor Monitor To the monitor via HDMI connector WN DVR User s Manual 14 Aurora Series Getting Started Connecting to Other Devices 4 Channel 8 Channel DVR ala H m O Z TT Speaker Connect the microphone using RCA cable connection Connect the speaker using RCA cable connection Alarm sensor in rin gt When using a PTZ speed Connect one dome connect the sensor in camera cable to the video device via RS 435 input of the DVR via connection RS 485 connector Alarm sensor device input Speed dome USB flash drive External hard drive with a USB compatible interface USB 2 0 DVR User s Manual Se 15 m Z dr I Aurora Series Getting Started 16 Channel DVR Speaker Microphone Connect the speaker using RCA cable connection Connect the microphone using RCA cable connection VIDEO IN en Ce eg HDMI RJ45 USB E SATA S S am Ge KiC t t Alarm sensor in When using a PTZ speed dome connect the Connect one camera cable to the video sensor in input of the DVR via device via RS 485 connector RS 485 connection Alarm sensor device input Speed dome ee E en G emm 00 Y tAUDIOs AUDIO CVBS HDMI RJ45 EES nl SS oo o ALM IN USB flash drive External hard drive with eSATA port drive with a USB compatible interface USB 2 0 WN DVR User s Manual 16 Aurora Series G
71. ue when the HDD is being accessed 3 OK Press to enter the selected menu item and 7 Link LED Lights green to indicate a valid network confirm the setting link is established on the LAN port 4 Direction keys Press to navigate the menus 8 Power LED Lights red to indicate the power is turned on Rear Panel 4 Channel DVR D _ VIDEONIN C u DC 12V HDMI IN 8 Channel DVR AUDIO OUT OU DC 12V HDMI IN DVR User s Manual Se 7 Aurora Series Introduction 16 Channel DVR m Z dr I EE VIDEO IN AUDIO CVBS OUT OUT fe 2 mme ie e Ai 1 Power Input Connects to the power adapter Use 8 Video Output Connects to a monitor or television only the supplied power adapter via BNC 2 HDMI Output Connects to a monitor via HDMI For 9 Video Input Connects to a maximum of 4 best video quality it is recommended to use this 4 channel DVR 8 8 channel DVR or 16 connection 16 channel DVR CCTV cameras BNC E note E note For best possible displayed image use a television The label shown on the port is the same channel or monitor which can display 1920x 1080 or higher number as it appears on the DVR interface 3 RS485 4 8 channel only Connects to a Speed 10 Audio Input Connects to a maximum of 4 dome camera via RS 485 4 channel DVR 8 8 channel DVR or 2 16 channel DVR microphones via RCA 4 VGA Output Connects to a VGA monitor 11 RS485 16 channel only Con
72. ure make sure in the following DDNS Dynamic DNS is a service that registers a domain name and the floating IP address with a DDNS server so that the domain name can be routed to the IP address even if the IP is changed in a dynamic IP system e You are using a broadband high speed DSL Cable Internet connection from the DVR side and the location you want to connect to the DVR e Your router supports DDNS or DynamicDNS Consult with your Internet Service Provider for this service e You need to create a DDNS account with KGUARD org server see http www kguard org or an account on DynDNS website DDNS Select Enable to enable this function Server Select the DDNS server Host name Enter the domain name you registered on DDNS server If the registered domain name is 123ABC KGUARD ORG the IP address you type on web browser when you browse Web Client is http 123ABC KGUARD ORG User Name Enter the DDNS User Name Password Enter the DDNS password E mail Advance MyKguard DDNS E MAIL UPnP Cloud E MAIL Enable Sending interval 5min Mail server SMTP 10 0 0 10 Port 25 Connection security None User name user Password EEN To user mail com Default Apply E DVR User s Manual When the e mail settings are properly configured and the function is activated the DVR will automatically send a notification e mail when events occur such as when motion is detected or the HDD fails at the specified channe
73. utomatically assign an IP address to your DVR connected to the Use the following IP address Select and configure it if you are using Static IP connection With Static IP connection your DVR is most likely connected to a DSL modem and your ISP has supplied you with a predefined IP for your Internet connection Obtain the following information from your network administrator or your Internet Service Provider ISP and type in accordingly IP address The address that identifies the DVR in the electronic network Your DVR uses IPv4 addressing which consists of four groups of numbers between 0 to 255 separated by periods For exapmle 192 168 1 35 Make sure that no other device in the LAN does not share the same IP address Subnet mask Subnet mask defines a range of IP addresses that can be used in a network If IP address is like a street where you live then subnet mask is like a neighborhood The subnet address consists of four groups of numbers separated by periods For example 255 255 255 0 Default gateway The address of the node router on a TCP IP network via is established the entrance into a network and vice versa Obtain DNS server address automatically Select to let the DVR to automatically choose a DNS server This option is only available if you are using DHCP connection Use the following DNS server addresses Select to manually configure the DNS server parameters Preferred DNS server Specify the prefer
74. versal Plug and Play is an universal protocol for widespread plug and play devices to ease the network implementation Many routers that support UPnP do not come with the feature enabled by default If this function does not work be sure to check if UPnP setting is enabled Advance MyKguard DDNS E MAIL Cloud Enable Enable Select Enable to activate the UPnP function After all settings are complete click Apply Default Apply DVR User s Manual a 53 m Z dr I Aurora Series Configuring DVR Settings Cloud Advance MyKguard DDNS Enable Interval Motion detection CH Receiver Server switch Mail server SMTP Port E MAIL UPnP 1min Enable A1 A2 Default Default Apply At present your DVR supports the Dropbox cloud storage Before setting up the cloud storage on the DVR make sure your Dropbox account has been created and active Dropbox website www dropbox com and the network settings of your DVR has been configured properly Enable Check the box to enable the cloud storage function Interval Select the interval time between uploading snapshots to the cloud storage Note To 1 minute interval option you can choose only 4 channels Motion detection Select Enable if you want the DVR to upload snapshots when motion is detected CH Check the respective channel box to upload the channel snapshots Receiver Enter your e mail account to receive the c
75. ype in the current date manually Date format Select the format you prefer the date to be displayed Time format Select the format you wish the time to be displayed The options are 24 hours or 12 hours DVR User s Manual J j 33 Aurora Series Configuring DVR Settings Time zone Select the time zone in your location Note The UK is GMT 0 00 and the East Coast of Australia is GMT 10 00 In the USA EST Eastern Standard Time is GMT 5 00 where PST Pacific Standard Time is GMT 8 00 Auto update Click to automatically set the date and time according to the network Time Server Choose the time server that will keep track of DST settings see in the following section Note If you choose to use the Time Server make sure your DVR has a constant Internet connection DST Daylight Saving Time Date Time SYSTEM Enable Mode Week Date DISPLAY Offset One hour Two hours RECORD From Mar Sun 02 00 00 To Nov Sun 02 00 00 Default Apply Offset Select the amount of time to offset for DST You can allow the DVR to automatically update its internal clock when daylight saving starts and ends Enable Check this option to allow the DVR automatically adjust the time for DST To disable uncheck this option Mode Select the DST mode e Week Enter the Start Time and End Time information by selecting the starting ending month week day and entering the starting ending

Kguard AR421-CKT001 Surveillance Combo Kit

Contents

Download Pdf Manuals

Related Search

Related Contents