Planar Systems PLL1911M
Contents
1. LCD monitor may determine it Moreover users are encouraged to correct interference by doing one or more of the following O Reorient or relocate the receiving antenna O Move the LED LCD monitor and the receiver further away from each other O Connect the LED LCD monitor into an outlet on a circuit different from that to which the receiver is connected O Consult your local dealer or an qualified technician FCC Warning To assure a continued FCC compliance a user must use a grounded power supply cord and the provided shielded video interface cable with bonded ferrite cores Also any unauthorized changes or modifications to this LED LCD monitor would void the user s authority to operate this device Note If necessary shielded interface cables and AC power cord must be used to meet the emission level limits COMMUNIQUE D AVERTISSEMENT DE LA FCC CONCERNANT LES INTERFERENCE DE FREQUENCE RADIO SEULEMENT POUR MODELES CERTIFIE PAR LA FCC Ce moniteur a t test et a t trouv conforme aux limites pour un appareil num rique de Classe B suivant la partie 15 des reglements de la FCC Ces limites ont te d velopp es pour offrir une protection satisfaisante contre les interf rences nuisibles dans une installation r sidentielle Ce moniteur g nere utilise et peut radier de l nergie de fr quence radio Ceci peut causer des interf rences nuisibles a des communication radio si l appareil n est pas convenablement install e2. sets Note O Move the LED out of the package and take off the plastic bag and Polystyrene Foam O Pull the base from Parallel versus Panel to Vertical O Adjust the Panel within 5 degree leaning forward and 19 degree leaning backward Safety Tips O if smoke abnormal noise or odor came out from your LED LCD monitor caution you should remove the power cord immediately and call your service center O Never remove the rear cover of your LED LCD monitor cabinet The display unit inside contains high voltage parts and may cause electric shock to human bodies O Never try to repair your LED LCD monitor yourself Always call your service center or a qualified technician to fix it i Troubleshooting No power O Make sure A C power cord is securely connected to the power adapter and the power supply is firmly connected to the LED LCD monitor O Plug another electrical device into the power outlet to verify that the outlet is supplying proper voltage O Make sure all signal cables are installed Power on but no screen image O Make sure the video cable supplied with the LED LCD monitor is tightly secured to the video output port on back of the computer If not tightly secure it O Adjust brightness Wrong or abnormal colors 0 if any colors red green blue are missing check the video cable to make sure it is securely connected Loose or broken pins in the cable connector could cause an improper connection O Connect the LED LCD monit
3. LCD monitor is manufactured and tested on a ground principle that a user s safety comes first However improper use or installation may result danger to the LED LCD monitor as well as to the user Carefully go over the following WARNINGS before installation and keep this guide handy WARNINGS This LED LCD monitor should be operated only at the correct power sources indicated on the label on the rear end of the LED LCD monitor If you re unsure of the power supply in your residence consult your local dealer or power company Do not try to repair the LED LCD monitor yourself as it contains no user serviceable parts The LED LCD monitor should only be repaired by a qualified technician Donot remove the LED LCD monitor cabinet There is high voltage parts inside that may cause electric shock to human bodies even when the power cord is disconnected Stop using the LED LCD monitor if the cabinet is damaged Have it checked by a service technician Put your LED LCD monitor only in a clean dry environment Unplug the LED LCD monitor immediately if gets wet and consult your service technician Always unplug the LED LCD monitor before cleaning it Clean the cabinet with a clean dry cloth Apply non ammonia based cleaner onto the cloth not directly onto the glass screen Keep the LED LCD monitor away from magnetic objects motors TV sets and transformer Do not place heavy objects on the cable or power cord For pluggabl
4. PLANAR PLL1911M LED LCD Monitor USER S GUIDE www planar com i Content SF NO IS COINS anses 1 Sale Precauciones 3 PISE E O cone toss beh can ea tn D a D a 5 Front VIVE ote PO S 7 Rear pos AA dt at it a mien eu 8 OR RS A OO i n 9 BASIC ODE SO 10 Advanced OperatiON OSD ME E E 12 SUP ON CMI TIMIDO MOdES ennen e E E A E ENE 15 Technical LINO MAO E EE E E AEA E AEE A A A A AE mana 16 Wal mournt ins UO essers an o iN EEE EEU EErEE a SONO AEE EEE IEA AENA TENNENT 17 A AIO MIAE N e E 18 TOUDE SNOOT eo a E E E A nn oo 18 PARA DOTE ae a 19 Operation Instructions Thank you for purchasing this edge lit LED LCD monitor a high resolution multi scan color LED LCD monitor Please read this guide thoroughly before installation FCC RADIO FREQUENCY INTERFERENCE STATEMENT WARNING FOR FCC CERTIFIED MODELS This LED LCD monitor has been tested and found compliant with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide proper protection against harmful interference to a residential installation This LED LCD monitor generates uses and can radiate radio frequency energy Harmful interference to radio communication may be led as a result if it s not properly installed and used However there is no guarantee that interference will not occur in a particular installation If this LED LCD monitor does cause serious interference to radio or television reception resetting the LED
5. e equipment the socket outlet shall be installed near the equipment and shall be easily accessible Due to safety concerns if the VESA mounting kit is purchased separately please make sure the mounting kit is UL Listed and replaceable only by service personnel AVERTISSEMENTS Ce moniteur doit tre utilis uniquement avec les sources d alimentation ad quates indiqu es sur l tiquette situ e au dos du moniteur Si vous n tes pas s r de l alimentation dans votre r sidence appelez votre vendeur local ou la compagnie d lectricit N essayez pas de r parer vous m me le moniteur car il ne contient pas de pi ces r parables par l utilisateur Le moniteur doit tre r par uniquement par un technicien qualifi Ne retirez pas le bo tier du moniteur Il contient des pi ces comportant un voltage lev qui pourraient provoquer des lectrocutions m me quand le cordon d alimentation est d branch Arr tez d utiliser le moniteur si le bo tier est endommag Faites le v rifier par un technicien qualifi Placez votre moniteur uniquement dans un environnement propre et sec D branchez imm diatement le moniteur s il tait mouill et faites appel a votre r parateur D branchez toujours le moniteur avant de le nettoyer Nettoyez le bo tier avec un chiffon propre et sec Appliquez un nettoyant sans ammoniaque sur le chiffon mais pas directement sur le verre de l cran Maintenez le moniteur loign d
6. e procedure below 1 Disconnect all the cables and cords from the Monitor to prevent breakage 2 Carefully place the Monitor face down on a soft and flat surface blanket foam cloth etc to prevent any damage to the Monitor Remove the screws so that the stand base can be removed Gently remove the stand base wm TT m 1 MOO I Attaching The Optional Wall Mount Arm not supplied 100mm x 100mm Screw ee ee e Mounting Options Follow these steps to finish installing the wall mounting arm 1 Place the wall mounting arm onto the back of the LED LCD monitor Line up the holes of the arm with the holes in the back of the monitor 2 Insert the 4 screws into the holes and tighten 3 Reconnect the cables Refer to the User s Guide that came with the optional wall mounting arm for instructions on attaching it to the wall TON 4mm 0 7 pitch threaded holes x 4 NOTE e 100mmx100mm VESA high hole n 4 M4 pitch 0 7 mm screw mounting kit not included 17 Care and Maintenance Care O Avoid exposing your LED LCD monitor directly to sunlight or other heat source Place your LED LCD monitor away from the sun to reduce glare O Put your LED LCD monitor in a well ventilated area O Do not place any heavy things on top of your LED LCD monitor O Make certain your LED LCD monitor is installed in a clean and moisture free area O Keep your LED LCD monitor away from magnets motors transformers speakers and TV
7. e stand from the monitor Front View of the Product ANA ss PEL Rear View of the Product i Quick Installation 1 Connect either VGA or DVI Video Source from the monitor to the computer Make sure both monitor and computer are powered OFF 2 Connect the audio cable from audio output of computer to the audio input of the monitor 3 4 Connect the power cord to a properly grounded AC outlet then to the monitor Power ON computer and then POWER ON the monitor Set the timing mode on your computer Recommended resolution and refresh rate is 1280X1024 60 Hz Example DVI cable Power cable Audio cable VGA cable Basic Operation Before using the LED LCD monitor Connect external equipments properly Insert the power plug and the power LED indicator will light orange Power On Off To turn the LED LCD monitor on off Press POWER button on the front of LED LCD monitor The power LED indicator lights green when the LED LCD monitor is on Using the OSD Menu You are able to use OSD menus to adjust various settings by using menu button on the front of the LED LCD monitor Display main menu Exit from OSD menu Selects between VGA DVI or Auto mode Press the button for three seconds to auto adjust the image VGA only a Confirm the selection Select the desired item when in OSD menu When not in OSD menu directly enters Audio Adjust a Select the desired item whe
8. es objets magn tiques moteurs postes de TV et transformateurs Ne placez pas d objets lourds sur le c ble ou le cordon d alimentation Pour les EQUIPEMENTS BRANCHES PAR C BLE la prise de courant doit tre install e pr s de l quipement et doit tre facilement accessible Pour les crans cadre brillant prenez en consid ration l emplacement de l cran car la lumi re environnante et les surfaces lumineuses peuvent se refl ter dans le cadre et g ner votre vision I First Setup Congratulations on your purchase of this high performance LED edge lit LCD monitor This LED LCD monitor comes with the following accessories e LEDLCD monitor e Power Cable e User s Guide e Audio Cable e VGA Cable e DVI Cable Installing the Stand Base iy ee as 7 ns F i Mi 5 AA Pr PAT EEIT ET FEA OO A e E EIA A 1 Turn the monitor over and set it upside down 2 Align the monitor to the slots on the stand 3 Turn the screw clockwise to attach the base to the monitor 4 Check the underside of the stand to ensure that the monitor has been firmly installed to the stand and that the screws do not loosen Monitor Adjustment The LED LCD Monitor is designed to have a tilt range of 5 to 19 aswivel range of 30 to 30 and a height adjustment of 4 3 110mm Disconnecting the Stand Base 1 Turn the monitor over and set it upside down 2 Turnthe screw counterclockwise to loosen it 3 Detach th
9. ff Memory Recall To recall factory settings for Video amp Audio controls Press button 2 to select the Memory Recall menu option 14 i Supporting Timing Modes STANDARD RESOLUTION VGA VGA MAC MAC Note DVI supports 480i 480p 576i 576p 720p Warning Do not set the graphic card in your computer to exceed these maximum refresh rates Doing so may result in permanent damage to your monitor Avertissement Ne r glez pas la carte graphique de votre ordinateur en d passant ces taux de rafraichissement maximaux Si vous le faites cela va irr m diablement d t riorer votre moniteur 15 f Technical Information Technical Specification Panel Power Management Displayable Resolution Pixel Dimension Display Color Tilt Active Display Area Temperature Compliance Power Speaker 19 TFT with LED backlight On 22 Watts typical 31 Watts maximum Standby Mode lt 0 5 Watt Off lt 0 5 Watt SXGA 1280x1024 max Vertical Frequency 75Hz max 0 294 x 0 294 mm 16 7M 5 19 376 32mm x 301 05mm Operating 0 C 40 C Storage 20 C 60 C FCC CE UL WEEE Input Voltage AC100 240 V 2W x 2 16 f Wall mount instruction Preparing To Install The Optional Wall Mount Arm not included This LED LCD monitor can be attached to a wall mounting arm you can purchase separately Turn the power OFF then disconnect the cables from the LED LCD monitor before performing th
10. n in OSD menu When not in OSD menu directly enters Preset Mode Recall both of Contrast and Brightness when not in OSD menu OSD Lock Out Function When LED LCD monitor is in normal display you can enable the OSD Lock Out function Option 1 OSD lock all 4 buttons are locked except the POWER button Press and hold the 1 button and the A button for 3 seconds to lock the OSD buttons The LED LCD monitor will show an OSD Lock Out message for 5 10 seconds and the message will disappear automatically Repeat this step to unlock Option 2 OSD amp Power button lock all 5 buttons including the POWER button are locked Press and hold the 1 button and the Y button for 3 seconds to lock all 5 buttons The LED LCD monitor will show an Lock Out message for 5 10 seconds and the message will disappear automatically Repeat this step to unlock 11 Advanced Operation OSD Menu You can use the OSD menu to adjust various settings for your LED LCD monitor Press the 1 button to display the OSD Menu and use A Y to select the desired OSD menu Contrast Brightness E Input Select Audio Adjust Color Adjust f Information G Manual Image Adjust setup Menu Memory Recall M Exit 2 Select Short Cuts Function from the button s E XX Auto Image Adjust To auto adjust Horizontal Position Vertical Position Phase Fine Tune and Clock H Size of the screen C
11. ontrast To adjust the foreground white level of screen image A increase contrast Y decrease contrast Brightness To adjust the luminance of the video A increase brightness Y decrease brightness ECO Allows the user to turn the ECO On or Off Contrast and Brightness adjustment disabled when ECO is active Input Select To select input source VGA DVI or Auto Audio Adjust To adjust the audio functions Volume To adjust the volume of speaker output Mute To turn the Mute ON OFF Eg Color Adjust To select the color for improving brightness and color saturation 12 a between 9300K 6500K 5400K and User Color 9300K Adds blue to screen image for cooler white 6500K Adds red to screen image for warmer white and richer red 5400K Adds green to screen image for a darker color User Color Individual adjustments for red R green G blue B 1 Press button 2 to select the desired color 2 Press Y or A button to adjust selected color Information To display the information regarding the current input signal coming from the graphic card in your computer Note See your graphic card user guide for more information about changing the resolution and refresh rate Manual Image Adjust To manually adjust the Horizontal Size H V position Fine Tune Sharpness and Preset Mode Horizontal Size To adjust the width of the screen image V decrease the width of screen image A increase the wid
12. or to another computer 18 Planar Support Cables and Accessories To find cables and accessories for your Planar monitor touch screen or other Planar products visit our online store at www PlanarOnline com Technical Support Visit Planar at http www planar com support for operations manuals touch screen drivers warranty information and access to Planar s Technical Library for online trouble shooting To speak with Planar Customer Support please have your model and serial number available and dial Planar Support Tel 1 866 PLANAR1 866 752 6271 or 1 503 748 5799 outside the US Hours 24 hours a day 7 days a week Toll or long distance charges may apply 19 Planar Systems Inc Customer Service 24x7 Online Technical Support http www planar com support 1195 NW Compton Drive Beaverton OR 97006 1992 Tel 1 866 PLANAR1 866 752 6271 or 1 503 748 5799 outside the United States Hours 24 hours a day 7 days a week 2013 Planar Systems Inc Planaris a registered trademark of Planar Systems Inc Other brands and names are the property of their respective owners Technical information in this document is subject to change without notice ill P N 200117 LL
13. t utilis Il n y n anmoins aucune garantie que des interf rences n apparaitront pas dans une installation particuli re Si ce moniteur cause de s rieuses interf rences la r ception de signaux radios ou t l vis es une possibilit est de r initialiser le moniteur Les usagers sont aussi encourag s corriger les interf rences en appliquant une ou plusieurs des d marches suivantes O R orientez ou d placez l antenne de r ception O Placez le moniteur et le r cepteur plus loin l un de l autre O Connectez le moniteur une prise diff rente de celle laquelle le r cepteur est connect O Consultez votre revendeur local ou un technicien qualifi Avertissement de la FCC Pour assurez une conformit continue au r glements de la FCC l utilisateur doit utiliser un cordon d alimentation mis terre et le cable d interface vid o prot g avec noyaux en ferrite fourni avec l appareil Chaque modification ou changement non autoris appliqu a ce moniteur peut faire perdre l utilisateur sont droit d op ration de cet appareil Note Si n cessaire des cables d interface prot g s et un cordon d alimentation alternante doivent tre utilis pour tre conforme aux limites d mission sd According to WEEE regulation this LED LCD monitor can t be handled as normal trash in Europe when it is out of usage Please refer to the recycle information from our website to handle it I Safety Precautions This LED
14. th of screen image H V Position To adjust the horizontal and vertical position of the video H Position A move screen to the right Y move screen to the left V Position A move screen up Y move screen down Fine Tune To adjust the delay time of data and clock Press Y or A to adjust to your preference Sharpness To adjust the clarity of a non SXGA 1280x1024 signal with V or A button Preset Mode Provides an optimum display environment depending on the contents displayed It contains 5 user selectable presets Standard is for general windows environment and monitor default setting Game optimized for PC game environment Cinema optimized for movie and video environment Scenery optimized for displaying outdoor scenery images Text optimized for text editing and viewing in a word processing environment Setup Menu To set up Language Select OSD Position OSD Time Out and OSD Background Language Select To allow users to choose from available languages OSD Position Press Y or A button to select between horizontal and vertical OSD Position adjustment 13 H Position To horizontally adjust the OSD position A move OSD to the right Y move OSD to the left V Position To vertically adjust the OSD position A move OSD up Y move OSD down OSD Time Out To automatically turn off On Screen Display OSD after a preset period of time OSD Background Allows the user to turn the OSD background On or O
Download Pdf Manuals
Related Search