Miele KM 6347 PowerFlex
Contents
1. S 1 Three finger locking by touching and the sensors for selecting the right hand cooking zones at the same time P 07 System lock S 0 Manual activation of the system lock only S 1 Manual and automatic activation of the System lock P 08 Auto heat up S 0 Off S 1 On P 10 Miele home S 0 Feature not fitted only on S 1 Signed off communication enabled appliances fitted witha S 2 Signedon communication module P 15 Audible tone ifasensor S 0 Off is covered S 4 On P 16 Sensor reaction speed S 0 Slow S 1 Normal S 2 Rapid Programmes Status numbers not shown here have no allocation The factory default settings are shown in bold 49 Problem solving guide With the help of the following notes minor faults in the performance of the appliance some of which may result from incorrect operation can be put right without contacting the Service Department Installation work and repairs to electrical appliances must only be carried out by a suitably qualified and competent person in strict accordance with current local and national safety regulations Do not attempt to open the casing of the appliance Repairs and other work by unqualified persons could be dangerous and Miele cannot be held liable for unauthorised work Problem Possible cause Remedy The hob or cooking zones cannot be switched on The mains fuse has tripped Reset the trip switch in the mains fuse box minimum f2. 65 Installationmotes soma a rear RR ee ee ee ae ne 65 Building in dimensions 66 KM 6322 2 24a een ken ee rasche ae 66 KM 6347 pre rica en nn er er a 67 Inst lling the hob sceur 844 208 tee rer enter ne 68 Flush fitted hobs 69 Building in dimensions 69 MOS Sa er es di a tere 69 AA A a BEE in 70 HiStal MOMS Mob ses ea po ae Gp mnt 71 Electrical connection 74 Wiring d agr m ide is ee 75 After sales service data plate guarantee 76 Warning and Safety instructions This hob complies with all relevant safety requirements Inappropriate use can however lead to personal injury and damage to property To avoid the risk of accidents and damage to the appliance please read these instructions carefully before installation and before using it for the first time They contain important notes on installation safety use and maintenance Miele cannot be held liable for damage caused by non compliance with these Warning and Safety instructions Keep these instructions in a safe place and ensure that new users are familiar with the content Pass them on to any future owner Warning and Safety instructions Correct application D This hob is not designed for commercial use It is intended for use in domestic hous
3. These can be ordered online at Miele www miele shop com or from Miele see back of manual for contact details Miele offer a wide range of pans which are perfect for Miele hobs Please refer to the Miele website for more details on individual products Pans in various sizes Frying pan with lid Non stick pans Wok Gourmet oven dish Cleaning products Ceramic and stainless steel hob cleaner 250 ml Removes heavy soiling limescale deposits and aluminium residues E Cloth microfibre cloth 54 Removes finger marks and light soiling Optional accessories Miele home system XKM 2100 KM XGW 2000 The Miele home system allows communication enabled appliances to send operating and status information to a display appliance via the household electrical supply system Powerline Technology SuperVision appliances can display status information from other domestic appliances For your hob the main status displayed is On Off Fault Status information for domestic appliances can be displayed and some controls operated within the home network area on a PC Notebook or iPod iPhone mobile terminals via a Miele home Gateway For your hob for example the following information is displayed Setting of each cooking zone minute minder switching off time for each cooking zone The only available control command is switch hob off iPod und iPhone are registered trade marks of Apple Inc
4. Miele Hong Kong Limited 41 F 4101 Manhattan Place 23 Wang Tai Road Kowloon Bay Hong Kong Tel 852 2610 1331 Fax 852 2610 1013 Email mielehk miele com hk India Miele India Pvt Ltd Ground Floor Copia Corporate Suites Plot No 9 Jasola New Delhi 110025 Tel 011 46 900 000 Fax 011 46 900 001 E mail customercare miele in Internet www miele in Ireland Miele Ireland Ltd 2024 Bianconi Avenue Citywest Business Campus Dublin 24 Tel 01 461 07 10 Fax 01 461 07 97 E Mail info miele ie Internet www miele ie Manufacturer Miele amp Cie KG Carl Miele StraBe 29 33332 G tersloh Germany Malaysia iele Sdn Bhd Suite 12 2 Level 12 enara SapuraKencana Petroleum Solaris Dutamas No 1 Jalan Dutamas 1 50480 kuala Lumpur Malaysia Phone 603 6209 0288 Fax 603 6205 3768 New Zealand iele New Zealand Limited 8 College Hill Freemans Bay Auckland 1011 NZ Tel 0800 264 353 Fax 0800 463 453 Internet www miele co nz Singapore Miele Southeast Asia Miele Pte Ltd 163 Penang Road 04 02 03 Winsland House Singapore 238463 Tel 65 6735 1191 Fax 65 6735 1161 E Mail infosea miele com sg Internet www miele sg South Africa iele Pty Ltd 63 Peter Place Bryanston 2194 P O Box 69434 Bryanston 2021 Tel 011 875 9000 Fax 011 875 9035 E mail info miele co za Internet www miele co za United Arab Emirates iele Appliances Ltd P O Box 11 4
5. Con ctivity is the communication between the hob and the cooker hood Operation of the cooker hood occurs automatically in conjunction with the hob The hob sends information on its operating status via the household electrical supply To enjoy the benefits of this feature your appliance needs to be fitted with a communication module Detailed information about the Miele home system can be found at www miele de Communication module including installation accessories for Miele hobs Miele home Gateway The gateway is the bridge between the Powerline communication of the appliances and your home network 55 Optional accessories Miele home 56 Communication enabled appliances examples Communication module SuperVision appliance Electrical supply Powerline Miele home Gateway 6 WLAN Router Possible connections optional PC Notebook iPod or iPhone Connection with a domestic bus system display Possible internet connection iPod und iPhone are registered trade marks of Apple Inc Optional accessories Con ctivity Communication module XKM 2000 DA 2 Communication module XKM 2100 KM Electrical supply Powerline 57 Con ctivity and Miele home Signing on the hob 58 If you want to sign the hob on to the Miele home system first prepare the signing on procedure on the master
6. Ensure that power is not supplied to the appliance until after it has been installed or until any maintenance or repair work has been carried out gt If the hob is fitted with a communication module in addition to disconnecting the hob this module must also be disconnected from the mains electricity during installation and maintenance of the hob as well as while any repair work is being carried out gt Danger of electric shock Do not use the hob if it is faulty or if the ceramic surface is cracked chipped or damaged in any way Switch it off immediately and disconnect it from the mains electricity supply gt In areas which may be subject to infestation by cockroaches or other vermin pay particular attention to keeping the appliance and its surroundings in a clean condition at all times Any damage which may be caused by cockroaches or other vermin will not be covered by the guarantee Warning and Safety instructions Correct use gt Oil and fat can overheat and catch fire Do not leave the appliance unattended when cooking with oil or fat If oil or fat does catch fire do not attempt to put out the flames with water Disconnect the appliance from the mains and use a suitable fire blanket saucepan lid damp towel or similar to smother the flames gt Flames could set the grease filters of a cooker hood on fire Do not flamb under a cooker hood gt Spray canisters aerosols and other inflammable substances ca
7. The overheating mechanism can be triggered by Heating up an empty pan Fat or oil being heated up on a high power level Insufficient ventilation to the underside of the appliance A hot cooking zone being switched on after a power cut If the overheating protection mechanism triggers again contact the Service department 43 Cleaning and care 44 Danger of injury Do not use a steam cleaning appliance to clean this appliance The steam could reach electrical components and cause a short circuit The appliance should be cleaned after each use Let it cool down to room temperature before cleaning To avoid water marks and limescale deposits use a soft cloth to dry the appliance after cleaning To avoid damaging the surface of your appliance do not use washing up liquid cleaning agents containing soda alkalines ammonia acids or chlorides cleaning agents containing descaling agents stain or rust removers abrasive cleaning agents e g powder cleaners and cream eaners O olvent based cleaning agents ishwasher cleaner S d grill and oven cleaners glass cleaning agents hard abrasive brushes or sponges e g pot scourers or sponges which have been previously used with abrasive cleaning agents melamine eraser blocks sharp pointed objects which could damage the seal between the ceramic surface and the surrounding frame and between the frame and the worktop Clea
8. m Touch the sensor for selecting the front right cooking zone and then touch the relevant number on the numerical keypad 46 Programming To save settings m Touch the sensor until all the displays go out To not save settings m Touch the sensor until all the displays go out 47 Programming Programme Status Setting P 00 Demonstration S O Demonstration mode on mode and after the hob is switched on JE will factory default appear in the timer display for a few settings seconds S 1 Demonstration mode off S 9 Factory default settings reinstated P 01 Stop and Go S O Off S 1 On P 02 Power level S 0 9 power levels range 1 2 3 to 9 S 1 17 power levels 1 1 2 2 3 to 9 If the Auto heat up setting is selected an A will flash alternately with the continued cooking setting in the display P 03 Induction S 0 Off warning tone S 4 Quiet when there is no pan or the pan S 2 Medium is unsuitable S 3 Loud P 04 Keypad tone S O Off when asensor g i Quiet is touched S 2 Medium S 3 Loud P 05 Timer audible S O Off tone S 1 Quiet for 10 seconds S 2 Medium for 10 seconds S 3 Loud for 10 seconds Programmes Status numbers not shown here have no allocation The factory default settings are shown in bold 48 Programming Programme Status Setting P 06 Safety lock s 0 One finger locking using
9. Normal 3400 15 x 23 23 x 39 TwinBooster level 1 4800 TwinBooster level 2 7400 Total 7400 Pans of any base diameter within the given range may be used The wattage quoted may vary depending on the size and material of the pans used 18 Guide to the appliance Cooking KM 6347 KM 6348 zone Minimum to maximum Rating in watts for 230 V in cm k 16 23 Normal 2300 TwinBooster level 1 3000 TwinBooster level 2 3700 P 10 16 Norma 1400 Booster 2200 9 15 23 Norma 2100 TwinBooster leve 3000 TwinBooster level 2 3700 d 15 23 Norma 2100 TwinBooster leve 3000 TwinBooster level 2 3700 Pl Ed 22 23 Normal 3400 15x23 23x39 TwinBooster leve 4800 TwinBooster level 2 7400 Total 7400 Pans of any base diameter within the given range may be used The wattage quoted may vary depending on the size and material of the pans used Caring for the environment Disposal of the packing material The packaging is designed to protect the appliance from damage during transportation The packaging materials used are selected from materials which are environmentally friendly for disposal and should be recycled Recycling the packaging reduces the use of raw materials in the manufacturing process and also reduces the amount of waste in landfill sites 20 Disposing of your old appliance Electrical and elect
10. a magnet to the base of the pan If the magnet sticks the pan is suitable Please be aware that the properties of the pan base can affect the eveness with which food heats up in the pan To make optimum use of the cooking zones choose pans with diameters larger than the innermost markings but smaller than the outermost markings If the diameter of the pan is smaller than the innermost marking the induction heating will not work The zone will behave as if it had no pan on it Often the maximum diameter quoted by manufacturers refers to the diameter of the top rim of the pot or pan The diameter of the base generally smaller is more important Danger of burning Make sure that pans are placed centrally on the cooking zone If a pan is placed only partially on a zone there is a risk that the handle could get very hot Power level range The appliance is delivered with 9 power levels programmed as standard If you wish to fine tune a setting you can extend the power level range see Programming The intermediate setting will be represented by an illuminated dot next to the number Bringing to the boil Settings Standard Extended factory settings settings 9 power levels 17 power levels Keeping warm h h Melting butter 1 2 1 2 Dissolving gelatine Making milk puddings 2 2 2 Warming small quantities of liquid 3 3 3 Cooking rice Defrosting frozen veget
11. appliance see the Miele home fitting and installation instructions onto the Con ctivity system first sign on the cooker hood see the Con ctivity fitting and installation instructions m With the hob switched off touch the D and amp sensors at the same time until the safety lock indicator light flashes After selecting programming mode P Programme and 5 Status will appear in the timer display On hobs with 3 cooking zones an additional indicator will appear at the rear left m Touch the sensor for selecting the front left cooking zone and then touch the 1 on the numerical keypad Set Programme 10 m Touch the sensor for selecting the front right cooking zone and then touch the 2 on the numerical keypad Set Status 2 Signed on The signing on process starts and the number 2 flashes The signing on process will take a few minutes The number 2 will light up constantly when the process has been completely successfully m To save the setting touch the O sensor until all the displays go out m Proceed as described in the Miele home or Con ctivity fitting and installation instructions Con ctivity and Miele home Signing off the hob If you want to sign off from the Miele home system first prepare the signing off procedure on the master appliance see the Miele home fitting and installation instructions m With the hob switched off touch the D and amp sensors at the same time until the safe
12. dot after the number are only available if the power level range has been extended see Programming Safety switch off if the sensors are covered 42 Your hob will switch off automatically if one or several of the sensors remain covered for more than about 10 seconds for example by finger contact food boiling over or by an object such as an oven glove or a tea towel F will appear in the timer display m Clean the control panel or remove the obstruction F will disappear You can now use the hob again Safety features Overheating protection All the induction coils and the cooling elements for the electronics are fitted with an overheating protection mechanism Before the induction coils or cooling elements get too hot the overheating protection mechanism cuts in in one of the following ways Induction coils If the booster function is being used this will be switched off The power level will be reduced The cooking zone will switch off automatically FE will flash in the timer display alternately with 44 You will be able to use the cooking Zones again as usual when the fault code has gone out Cooling elements If the booster function is being used this will be switched off The power level will be reduced The cooking zones will switch off automatically The affected cooking zones can only be used again as usual once the cooling element has cooled down to a safe level
13. fridge freezer freezer dishwasher washing machine washer dryer or tumble dryer D This hob must not be installed above ovens or cookers unless these have a built in cooling down fan 60 gt After installation ensure that the connection cable is without hindrance and that there is no mechanical obstruction which could damage it All dimensions in this instruction booklet are given in mm Safety distances Safety distance above the appliance When two or more appliances which have different safety distances are installed together below a cooker hood you should observe the greatest safety distance A minimum safety distance must be maintained between the appliance and the cooker hood above it See the cooker hood manufacturer s operating and installation instructions for details If the manufacturer s instructions are not available for the cooker hood a minimum safety distance of at least 760 mm must be maintained For any flammable objects e g utensil rails wall units etc a minimum distance of at least 760 mm must be maintained between them and the appliance below 61 Safety distances Safety distances to the sides and back of the hob Ideally the hob should be installed with plenty of space on either side There may be a wall at the rear or a tall unit or wall on one side right or left see illustrations Minimum distance of 50 mm between the back of the worktop cut out and the rear
14. less the thickness of the cladding must be maintained between the cut out and the cladding Example 15 mm niche cladding 50 mm 15 mm minimum safety distance of 35 mm Flush fitted hobs Hob with frame or bevelled edge Masonry 2 Niche cladding Dimension x thickness of niche cladding material 3 Worktop Worktop cut out Minimum safety distance for combustible materials is 50 mm for non combustible materials is 50 mm less dimension x 64 Hob with frame or bevelled edge Installation notes Tiled worktop Seal between the hob and the worktop Grout lines and the hatched area underneath the hob frame must be smooth and even If they are not the hob will not sit flush with the worktop Do not use sealant between the hob and the sealing strip underneath the and the worktop This could result in hob will not provide a good seal damage to the hob or the worktop if between the hob and the worktop the hob ever needs to be removed for servicing The sealing strip under the edge of the top part of the appliance provides a sufficient seal for the worktop 65 Hob with frame or bevelled edge Building in dimensions KM 6322 Front E Casing depth 3 Connection for Miele home 4 Mains connection box The mains connection cable 1440 mm long is supplied separately 66 Hob with frame or bevelled edge KM 6347 Front Casing depth
15. the appliance to the mains supply Consult a qualified electrician if in any doubt gt Do not connect the appliance to the mains electrical supply by an extension lead These are a fire hazard and do not guarantee the required safety of the appliance gt For safety reasons this appliance may only be used after it has been built in D This appliance must not be used in a non stationary location e g on a ship gt Do not open the casing of the appliance Tampering with electrical connections or components and mechanical parts is highly dangerous to the user and can cause operational faults Warning and Safety instructions D While the appliance is under guarantee repairs should only be undertaken by a service technician authorised by Miele Otherwise the guarantee is invalidated gt The manufacturer can only guarantee the safety of the appliance when original Miele replacement parts are used Faulty components must only be replaced by genuine Miele original spare parts D The hob is not intended for use with an external timer switch or a remote control system gt The hob must be connected to the electrical supply by a qualified electrician If the connection cable is faulty it must be replaced with a special connection cable installed by a qualified electrician See Electrical connection gt The appliance must be disconnected from the mains electricity supply during installation maintenance and repair work
16. to flash The cooking zone or the timer is active whilst the displays are flashing and you can set a power level or time Exception If only one of the cooking zones is in operation you can alter the power level without activating the cooking zone Take care to keep the control panel clean and do not place anything on top of it The sensors may fail to react or they could mistake the article or any dirt for a fingertip contact thereby activating a function or even causing the hob to switch off automatically see Safety switch off Do not place hot pans on the sensors The electronic unit underneath could get damaged Operation Fire hazard Do not leave the appliance unattended whilst it is being used To switch the hob on m Touch the D sensor will appear in each of the cooking zone displays If no further entry is made the hob will switch itself off after a few seconds for safety reasons Activating the cooking zones m Touch the sensor for selecting the cooking zone you want A 8 will flash in the cooking zone display Setting the power level Standard power level range m Touch the appropriate number on the numerical keypad The power level selected flashes in the display for a few seconds to start with and then lights up constantly Extended power level range see Power level range m Touch the area between the numbers The power level selected flashes in the display for a few seconds to start wi
17. 3 Connection for Miele home 4 Mains connection box The mains connection cable 1440 mm long is supplied separately 67 Hob with frame or bevelled edge Installing the hob Installing the hob Preparina the worlds m Feed the mains connection cable p 9 P down through the cut out nate a Hi ee m Place the hob centrally in the cut out a ae gt 09 a bert When doing this make sure that the sar ae m ec an seal under the hob sits flush with the ae 2 ia S insi LL worktop on all sides This is important S FERRER to ensure an effective seal all round Do not use sealant e g silicone m Seal the cut surfaces with a suitable heat resistant sealant to avoid swelling caused by moisture If the seal does not meet the worktop correctly on the corners the corner radius lt R4 can be carefully Make sure that the sealant does not scribed to suit come into contact with the top of the worktop m Connect the hob to the mains m Check that the hob works No spring clamps are needed to install the hob The seal underneath the hob will hold it securely on the worktop Any gap between the frame and worktop will reduce with time Connecting the mains cable to the appliance The mains cable must only be connected to the appliance by a qualified and competent electrician in strict accordance with current local and national safety regulations BS 7671 in the Uk m Follow the instructions in the wiring di
18. 7 82 Gold amp Diamond Park Sheikh Zayed Road Building 6 Offices Nos 6 214 to 6 220 Dubai Tel 971 4 341 84 44 Fax 971 4 341 88 52 E Mail info miele ae Internet www miele ae 79 KM 6322 KM 6323 KM 6347 KM 6348 CE en GB M Nr 09 524 040 01
19. A Miele Operating and installation instructions Ceramic hobs with induction To avoid the risk of accidents or damage to the appliance it is essential to read these instructions before it is installed and used for the first time en GB M Nr 09 524 040 Contents Warning and Safety instructions 5 Guide to the appliance 14 Models 007040 ta ie eine Et NOM Ne oY na 14 KM 6322 KM 6323 14 KM 6347 KM 6348 15 Control Panel ss au hrs b yer Shee aa ine Er ABER een 16 COOKING ZONE Sc or NN ANNE NAN Biest 18 Caring for the environment 20 Before using for the first time 21 Cleaning for the first time 21 Before using for the first time 21 INGUCHION erica a EA Ende bees aan 22 The induction principle 2 eee 22 NAS E OA 23 POS A ii Eee EE eae 24 Power level range 25 Operation coccion ade a adas 26 how the hobils Operated csi a a ee Bae an en 26 TOS WitCH MS NOD ON urna na a ea ee ean doe 27 Activating the cooking zones 27 Setting the power level 0 0 o 27 Altering the power level sses cree ae nb S
20. ables 3 2 3 Making porridge 3 2 3 Warming liquid and semi solid foods 4 4 4 Making omelettes and lightly frying eggs Steaming fruit Cooking dumplings 4 4 5 Steaming vegetables and fish 5 5 Defrosting and heating frozen food 5 5 5 Bringing large quantities of food to the boil e g 6 casseroles Thickening custard and sauces e g hollandaise Gently frying eggs without overheating the fat 6 5 6 Gently braising meat fish and sausages without overheating 7 6 7 the fat Frying pancakes etc f 6 7 Cooking stew 8 8 8 Boiling large quantities of water 9 9 These settings should only be taken as a guide The power of the induction coils will vary depending on the size and material of the pan For this reason it is possible that the settings will need to be adjusted slightly to suit your pans As you use the hob you will get to know which settings suit your pans best 25 Operation How the hob is operated 26 The hob is equipped with electronic sensor controls which react to finger contact To operate the hob touch the relevant sensor Each time you touch a sensor an audible tone sounds In order to set or alter a power level or the time depending on model the cooking zones and the timer must be active To activate a cooking zone or the timer touch the sensor for selecting the relevant cooking zone or the timer After you have touched the sensor the relevant cooking zone or timer display will start
21. agram see Electrical connection Wiring diagram 68 Flush fitted hobs Building in dimensions KM 6323 Front Please take careful note of the Casing depth detailed diagrams for the cut out 3 Connection for Miele home dimensions in granite and marble 4 Stepped cut out for granite or marble worktops worktops Mains connection box The mains connection cable 1440 mm long is supplied separately 69 Flush fitted hobs KM 6348 O Front Please take careful note of the detailed diagrams for the cut out chou dimensions in granite and marble 3 Connection for Miele home worktops a Stepped cut out for granite or marble worktops Mains connection box The mains connection cable 1440 mm long is supplied separately 70 Flush fitted hobs Installing the hob Flush fit hobs are only suitable for installation in granite marble tiled or solid wood worktops When using a worktop made from any other material please check first with the worktop manufacturer that it is suitable for installing a flush fit hob Certain models are suitable for building into glass worktops please see advice under Building in dimensions The internal width of the base unit must be at least as wide as the internal cut out width for the hob see Building in dimensions This is to ensure that the casing can be easily removed for maintenance If the underside of the hob is not freely a
22. ally see Programming If an unavailable sensor is touched whilst the safety lock or system lock is activated the safety lock indicator will light up and L will appear in the timer display for a few seconds The safety lock is programmed at the factory for three finger operation You can alter the setting from three finger to one finger operation see Programming If there is an interruption to the power supply the safety lock and the system lock will be deactivated 39 Safety features Activating Deactivating 40 Three finger operation standard default setting m Touch the sensor and the sensors for selecting both right hand cooking zones at the same time until the safety lock indicator lights up and LE appears in the timer display The safety lock indicator and LE will go out after a short while One finger operation m Touch the sensor until the safety lock indicator lights up and appears in the timer display The safety lock indicator and LE will go out after a short while Three finger operation standard default setting m Touch the sensor and the sensors for selecting both right hand cooking zones at the same time until the safety lock indicator and LE in the timer display go out One finger operation m Touch the sensor until the safety lock indicator and LE in the timer display go out Safety features Stop and Go Activating Deactivating Your appliance has a S
23. at the end of the auto heat up time In the extended range of power levels see Programming A flashes alternately with the continued cooking setting during the heat up time Altering the continued cooking setting will deactivate auto heat up To deactivate Auto heat up m Touch the sensor for selecting the cooking zone you want The cooking zone display will flash m Touch the continued cooking setting which has been selected until the indicator light or A goes out or m Select a different power level 29 Operation Continued Heat up time cooking setting in minutes and seconds approx 1 0 15 1 0 15 2 0 15 2 0 15 3 0 25 3 0 25 4 0 50 4 0 50 5 2 00 5 5 50 6 5 50 6 2 50 7 2 50 T 2 50 8 2 50 8 2 50 9 E The continued cooking settings with a dot after the number are only available if the power level range has been extended see Programming 30 Operation Booster The cooking zones are equipped with a Booster or TwinBooster see Guide to the appliance When activated the power is boosted for a maximum of 15 minutes so that large quantities can be heated up quickly e g when boiling water for cooking pasta The Booster function can only be used on two cooking zones at the same time If the Booster function is switched on when no setting has been selected the cooking zone will revert automatica
24. ccessible after installation any sealant used to plug the gaps around the appliance must be removed to enable the hob to be lifted out of the cut out should this be necessary The hob can be installed ina suitable cut out in a granite or marble worktop ina suitable cut out in a tiled or solid wood worktop or a glass worktop with a wooden support frame The frame must be provided on site and is not supplied with the appliance 71 Flush fitted hobs Granite and marble worktops Preparing the worktop Worktop 2 Hob Gap As the ceramic glass and the worktop cut out have a certain dimensional tolerance the size of gap can vary min 1 mm m Make the worktop cut out as shown in Building in dimensions Observe the safety distances see Safety instructions for installation 72 Connecting the mains cable to the appliance The mains cable must only be connected to the appliance by a qualified and competent electrician in strict accordance with current local and national safety regulations BS 7671 in the Uk m Follow the instructions in the wiring diagram see Electrical connection Wiring diagram Installing the hob m Feed the mains connection cable down through the cut out m Centre the hob in the cut out m Connect the hob to the mains m Check that the hob works m Seal the remaining gap with a silicone sealant that is heat resistant to at lea
25. ching it back on see Safety switch off The overheating protection mechanism has triggered See Overheating protection The Booster has deactivated early automatically The cooking zone is not working in the usual way at the power level set The overheating protection mechanism has triggered See Overheating protection 51 Problem solving guide Problem Possible cause Remedy Power level 9 is automatically reduced if you select power level 9 on two linked cooking zones or extended zones at the same time Operating both zones at power level 9 would exceed the permitted maximum power level for the two zones The hob switches off while it is in use and an F flashes in the timer display One or more of the sensors have been covered e g by finger contact food boiling over or by an object such as an oven glove Clean the control panel or remove the obstruction see Safety switch off The food in the pan hardly heats up or does not heat up at all when the Auto heat up function is switched on There is too much food in the pan Start cooking at the highest power level and then turn down to a lower one manually later on The pan is not conducting heat properly The cooling fan continues to run after the appliance has been switched off The fan will continue running until the appliance has cooled down It will
26. e a eee baie dis ae 28 PowerFlex cooking area eee 28 AUTO GALLUS rasen ee erde 29 BOOSTER was rana tranca Se Er a ety a ae Pe ee 31 Keeping warm function ooooooccccoo 33 Switching off and residual heat indicators 34 Tips on saving energy 35 Timer u a 204 ote Na bebe eh a bash eee 36 Minuteiminder 4 4 0 0 iii ain peed bee dade a interested 36 To switch a cooking zone off automatically 37 To use both timer functions at the same time 38 Safety features 2 eee ene 39 Safety lock System lock ai tease care es pong ee ey ewe a 39 SIOD and Oreste eats Wee ee Geta acd Bad alte teinte 41 Safety SWICHAOTM aid ta tad ae 42 Overheating protection 0 2 tees 43 Contents Cleaning and care 44 Programming oeie dee eed howe hea dha ada a ba eee 46 Problem solving guide 50 Optional accessories 54 Con ctivity and Miele home 58 SONNO On the MOD LAN as MR ead eee chs 58 SignINg Off the POB es ias raro ran era NF er ae 59 Safety instructions for installation 60 Safety distances 61 Hob with frame or bevelled edge
27. e is switched on either deliberately or by mistake or when there is residual heat present there is the risk of any metal items left on the hob heating up with the danger of burning Depending on the material other items left on the hob could also melt or catch fire Damp pan lids might adhere to the ceramic surface and be difficult to dislodge Do not use the appliance as a resting place Switch the cooking zones off after use gt Do not allow solid or liquid sugar or pieces of plastic or aluminium foil to get onto the cooking zones when they are hot as they can damage the ceramic surface when it cools down If this should occur switch off the appliance and scrape off all the sugar plastic or aluminium residues whilst still hot using a shielded scraper blade Wear oven gloves Allow the cooking zones to cool down and then clean them with a suitable ceramic hob cleaning agent gt Pans which boil dry can cause damage to the ceramic glass Do not leave the appliance unattended whilst it is being used gt Do not use pots or pans on the hob with bases with pronounced edges or ridges These could scratch or scour the ceramic glass surface permanently Only use pots and pans with smooth bases gt Lift pans into position on the hob Sliding them into place can cause scuffs and scratches Warning and Safety instructions gt Grains of salt sugar and sand e g from cleaning vegetables can cause scratches if they get und
28. edge of the worktop Minimum distance of 50 mm between the worktop cutout and a wall or tall unit to the right of it 3 Minimum distance of 50 mm between the worktop cutout and a wall or tall unit to the left of it 62 Not recommended Safety distances Safety distances underneath the hob To ensure sufficient ventilation to the hob a certain gap must be left between the underside of the hob and any oven interim shelf or drawer The minimum gap between the underside of the hob and the top of an oven is 15 mm the top of an interim shelf is 15 mm the base of a drawer is 75 mm Interim shelf It is not necessary to fit an interim shelf underneath the hob but one may be fitted if you wish Leave a gap of 10 mm at the back of the shelf to accommodate the cable We recommend a gap at the front of the shelf of 20 mm to ensure good ventilation 63 Safety distances Safety distance when installing the appliance near a wall with additional niche cladding A minimum safety distance must be maintained between the worktop cut out and any niche cladding to protect it from heat damage If the niche cladding is made from a combustible material e g wood a minimum safety distance of 50 mm must be maintained between the cut out and the cladding If the niche cladding is made from a non combustible material e g metal natural stone ceramic tiles a minimum safety distance of 50 mm
29. eholds and similar working and residential environments gt The appliance is not intended for outdoor use gt It is intended for domestic use only to cook food and keep it warm Any other use is not supported by the manufacturer and could be dangerous gt The appliance can only be used by people with reduced physical sensory or mental capabilities or lack of experience and knowledge if they are supervised whilst using it or have been shown how to use it in a safe way and recognise and understand the consequences of incorrect operation Warning and Safety instructions Safety with children D Children under 8 years of age must be kept away from the appliance unless they are constantly supervised gt Children 8 years and older may only use the appliance unsupervised if they have been shown how to use it in a safe way and can recognise and understand the consequences of incorrect operation D Children must not be allowed to clean the appliance unsupervised gt This appliance is not a toy To prevent the risk of injury do not allow children to play with the appliance or its controls gt The appliance gets hot when in use and remains hot for a while after being switched off Keep children well away from the appliance until it has cooled down and there is no danger of burning gt Danger of suffocation Packaging e g plastic wrappings must be kept out of the reach of babies and children Whilst playing childre
30. er pan bases Make sure that the ceramic surface is clean before placing pans on it gt Even a light object could cause damage in certain circumstances Do not drop anything on the ceramic surface gt Do not place hot pans on the sensors and display as this could cause damage to the electronics underneath Do not place hot pans on the area around the display D Induction heating works extremely quickly and so the base of the pan could heat up to the temperature at which oil or fat self ignites within a very short time Do not leave the appliance unattended whilst it is being used gt Heat oil or fat for a maximum of one minute Do not use the Booster function to heat oil or fat gt For people fitted with a heart pacemaker Please note that the area immediately surrounding the hob is electromagnetically charged It is unlikely to affect a pacemaker However if in any doubt consult the manufacturer of the pacemaker or your doctor gt To prevent damage to items which are susceptible to magnetic fields e g credit cards digital storage devices pocket calculators etc do not leave them in the immediate vicinity of the hob B Metal utensils stored in a drawer under the hob can become hot if the appliance is used intensively for a long time Do not store any metal items or utensils in a drawer under the hob 12 Warning and Safety instructions D This hob is fitted with a cooling fan If a drawer is fitted directly und
31. erneath the hob ensure that there is sufficient soace between the drawer and its contents and the underside of the appliance in order to ensure sufficient ventilation of the hob Do not store pointed or small items or paper in the drawer They could get in through the ventilation slots or be sucked into the housing by the fan and damage the fan or impair cooling gt Do not use two pans on a cooking zone extended zone or PowerFlex zone at the same time Cleaning and care gt Do not use a steam cleaning appliance to clean this appliance The steam could reach electrical components and cause a short circuit gt If the hob is built in over a pyrolitic oven or cooker the hob should not be used whilst the pyrolitic process is being carried out as this could trigger the overheating protection mechanism on the hob see relevant section Guide to the appliance Models KM 6322 KM 6323 O O M0 Cooking zones with Booster 3 PowerFlex cooking zone with TwinBooster can be combined with to form a PowerFlex cooking area 2 PowerFlex cooking zone with TwinBooster Control panel 14 Guide to the appliance KM 6347 KM 6348 Miele LIII INDUCTION D ee w B Bu 0123456789 a 10 Cooking zones with Booster 3 PowerFlex cooking zone with TwinBooster can be combined with a to form a PowerFlex cooking area 2 PowerFlex cooking zone with TwinBooster Control panel Gu
32. he hob must be switched on to use the timer The timer can be used for two different functions to set the minute minder to set a cooking zone to switch off automatically You can enter a time up to a maximum of 99 minutes To set the minute minder time Example You want to set 15 minutes m Switch the hob on m Touch the sensor 88 will appear in the timer display The on the right will flash Enter the tens first and then the units m Touch the number on the numerical keypad which corresponds to the tens position 1 in this case The timer display will change and 7 will start flashing m Touch the number on the numerical keypad which corresponds to the units position 5 in this case The timer display will change The 1 moves to the left and 5 appears on the right The minute minder time will begin to count down To change the minute minder time m Touch the sensor m Set the time you want as described above Deleting the minute minder time 36 m Touch the sensor until G8 appears in the timer display Timer To switch a cooking zone off automatically You can set a time at the end of which a cooking zone will switch off automatically All the cooking zones can be programmed at the same time If the time programmed is longer than the maximum operational time allowed the cooking zone will switch off after the maximum time allowed see Safety switch off m Select a powe
33. icone sealant that has been especially formulated for granite and marble 73 Electrical connection All electrical work should be carried out by a suitably qualified and competent person in strict accordance with current local and national safety regulations BS 7671 in the UK Installation repairs and other work by unqualified persons could be dangerous The manufacturer cannot be held liable for unauthorised work damaged cable must be replaced by a suitably qualified electrician with a special connection cable of type H 05 VV F available from Miele Ensure power is not supplied to the appliance until after installation or repair work has been carried out The appliance must only be operated when built in This is to ensure that all electrical parts are shielded Live parts must not be exposed Do not connect the appliance to the mains electricity supply by an extension lead These do not guarantee the required safety of the appliance Please make sure that the connection data quoted on the data plate match the household mains supply 74 Connection should be made via a suitable isolator which complies with national and local safety regulations and the On Off switch should be easily accessible after the appliance has been built in If the switch is not accessible after installation depending on country an additional means of disconnection must be provided for all poles For extra safety it
34. ide to the appliance Control panel Sensor controls On Off 2 Numerical keypad For setting the power level For setting the time E Safety lock a Booster TwinBooster 5 For selecting the cooking zone For switching on the PowerFlex cooking area For selecting the timer For switching between the timer functions For selecting the switch off time see Switching off a cooking zone automatically Stop and Go 16 Guide to the appliance Indicator lights O Safety lock Booster Cooking zone displays co Il Cooking zone ready for use Keeping warm function Power levels Level 1 TwinBooster Booster TwinBooster level 2 No pan on cooking zone or pan unsuitable see Induction Residual heat Auto heat up when the power level range has been extended Do 42 Indicator light for Auto heat up or extended power setting see Programming Timer display 43 Indicator light for relevant zone e g the rear right cooking zone Duration in minutes Guide to the appliance Cooking zones Cooking KM 6322 KM 6323 zus Minimum to maximum Rating in watts for 230 V in cm k 14 20 Norma 1850 Booster 3000 P 10 16 Norma 1400 Booster 2200 9 15 23 Norma 2100 TwinBooster level 1 3000 TwinBooster level 2 3700 dl 15 23 Norma 2100 TwinBooster level 1 3000 TwinBooster level 2 3700 Pl Ed 22 23
35. is advisable to protect the appliance with a residual current device RCD Please contact a qualified electrician for advice When switched off there must be an all pole contact gap of at least 3 mm in the isolator switch including switch fuses and relays Important U K The appliance is supplied for connection to a 230 240 V 50 Hz supply with a 3 core cable The wires in the mains lead are coloured in accordance with the following code Green yellow earth Blue neutral Brown live WARNING THIS APPLIANCE MUST BE EARTHED Electrical connection The electrical safety of this appliance can only be guaranteed when continuity is complete between it and an effective earthing system which complies with current local and national safety regulations It is most important that this basic safety requirement is present and regularly tested and where there is any doubt the electrical wiring in the home should be inspected by a qualified electrician The manufacturer cannot be held liable for the consequences of an inadequate earthing system such as an electric shock The manufacturer cannot be held liable for damage which is the direct or indirect result of incorrect installation or connection Wiring diagram 200 240 V 200 240 V L1 200 240 V L2 N B This appliance is supplied single phase only in the U K AUS NZ 15 After sales service data plate guarantee In the even
36. liance is switched on either deliberately or by mistake or when there is residual heat present there is the risk of the metal items heating up with the danger of burning Switch the hob off after use Induction Noises When using an induction cooking zone the following noises can occur in the pan depending on what it is made of and how it has been constructed On the higher power levels it might buzz This will decrease or cease altogether when the power level is reduced If the pan base is made of layers of different materials e g in a sandwiched base it might emit a cracking sound Whistling might occur if linked zones see Booster are being used at the same time and the pans also have bases made of layers of different materials You might hear a clicking sound from the electronic switches especially on lower power levels You might hear a whirring sound when the cooling fan switches on It switches on to protect the electronics when the hob is being used intensively The fan may continue to run after the appliance has been switched off 23 Induction Pans 24 Suitable pans include stainless steel pans with a magnetic base enamelled steel pans cast iron pans Unsuitable pans stainless steel pans without a magnetic base aluminium and copper pans glass ceramic or earthenware pots and pans To test whether a pot or pan is suitable for use on an induction hob hold
37. light for the cooking zone you require flashes Shortly after the last entry the timer display switches to the function with the shortest remaining time If you want to show the times remaining which are counting down in the background touch the repeatedly until the indicator light for the cooking zone you want flashes automatic switch off only the timer display is flashing minute minder Starting with the shortest time remaining which is shown in the display all cooking zones which are switched on and the minute minder are selected clockwise 38 Safety features Safety lock System lock Keep children away from the hob for their own safety Your appliance is equipped with a safety lock to prevent the hob and the cooking zones being switched on or any settings being altered The safety lock is set with the hob switched on When activated The cooking zone power levels and the timer settings cannot be changed The cooking zones the hob and the timer can be switched off but once switched off cannot be switched on again The system lock is set with the hob switched off When activated the hob cannot be switched on and the timer cannot be used The default setting for activating the system lock is manual The system lock can also be set for manual and automatic activation in which case it will be activated automatically five minutes after the hob has been switched off unless you set it manu
38. lly to setting 9 at the end of the booster time or if the booster function is switched off before this a setting has been selected the cooking zone will revert automatically to the setting selected at the end of the booster time or if the booster function is switched off before this Taking a pan off the zone whilst the Booster is in operation will not interrupt the Booster time Cooking zones are networked in pairs to supply the power for the Booster function When the Booster function is selected a proportion of energy is taken away from the linked cooking zone and the following happens within the pairs Auto heat up is deactivated The power level is reduced The linked cooking zone is switched off 31 Operation To switch on the Booster m Touch the sensor for selecting the cooking zone you want m Select a power level if you wish m Touch the B III sensor The indicator light for the booster lights up and 1 starts to flash in the display After a few seconds 1 will light up constantly and the indicator light will go out To switch on the TwinBooster Level 1 m Touch the sensor for selecting the cooking zone you want m Select a power level if you wish m Touch the B III sensor The indicator light for the booster lights up and starts to flash in the display After a few seconds will light up constantly and the indicator light will go out Level 2 m Touch the sensor for selecting the c
39. n ignite when heated Therefore do not store such items or substances in a drawer under the appliance Cutlery inserts must be heat resistant gt Do not heat an empty pan gt Do not heat up unopened tins of food on the hob as pressure will build up in the tin causing it to explode gt Do not cover the hob e g with a hob cover a cloth or protective foil The material could catch fire shatter or melt if the appliance is switched on by mistake or if residual heat is still present D When using an electrical appliance e g a hand held food blender near the appliance ensure that the cable of the electrical appliance cannot come into contact with the hot appliance The insulation on the cable could become damaged gt If the appliance is installed behind a kitchen furniture door it may only be used with the furniture door open Do not close the door whilst the hob in use or whilst there is any residual heat present gt The appliance gets hot when in use and remains hot for a while after being switched off There is a danger of burning until the residual heat indicators go out 10 Warning and Safety instructions gt You could burn yourself on the hot hob Protect your hands with heat resistant pot holders or gloves when handling hot pots and pans Do not let them get wet or damp as this causes heat to transfer through the material more quickly with the risk of scalding or burning yourself B gt When the applianc
40. n could become entangled in packaging or pull it over their head and suffocate gt Danger of burning Do not store anything which might arouse a child s interest in storage areas above or behind the appliance Otherwise they could be tempted into climbing onto the appliance gt Danger of burning or scalding Place pots and pans on the cooking zone in such a way that children cannot pull them down and burn themselves gt Activate the system lock to ensure that children cannot switch on the appliance inadvertently Use the safety lock when the hob is in use to prevent children from altering the settings selected Warning and Safety instructions Technical safety gt Unauthorised installation maintenance and repairs can cause considerable danger to users Installation maintenance and repair work must only be carried out by a Miele authorised technician gt A damaged appliance can be dangerous Check the appliance for visible signs of damage Do not use a damaged appliance gt The electrical safety of this appliance can only be guaranteed if correctly earthed It is most important that this basic safety requirement is observed and regularly tested and where there is any doubt the installation should be inspected by a qualified electrician gt To avoid the risk of damage to the appliance make sure that the connection data frequency and voltage on the data plate corresponds to the household supply before connecting
41. nger food is kept warm for the greater the loss of nutrients Try to ensure that food is kept warm for as short a time as possible 33 Operation Switching off and residual heat indicators Switching off a cooking zone m Touch the sensor for selecting the cooking zone you want twice A 8 will flash in the cooking zone display for a few seconds If the cooking zone is still hot the residual heat indicator will then appear in the display Switching off the hob m Touch the D sensor This switches off all cooking zones The residual heat indicator will appear in the display of any cooking zone which is still hot Residual heat indicator 34 The lines of the residual heat indicator go out one after another as the cooking zone cools down The last horizontal line only goes out when the cooking zone is safe to touch Danger of burning and fire hazard Do not touch the cooking zones whilst the residual heat indicators are lit up Tips on saving energy Use a pan lid whenever possible to minimise heat loss CSL uncovered covered Select a smaller pan when cooking small quantities A smaller pan uses less energy than a larger pan with very little in it Cook with as little water as possible Once food has come to the boil or the oil in the pan is hot enough for frying reduce the heat to a lower setting Cooking times are greatly reduced when using a pressure cooker 35 Timer Minute minder T
42. ning and care Do not use washing up liquid to clean the ceramic surface Washing up liquid will not remove all soiling and deposits It will form an invisible coating which will cause permanent discolouration of the ceramic surface Clean the hob regularly with a suitable ceramic hob cleaning agent Wipe off all coarse soiling using a damp cloth Stubborn soiling may need to be removed with a shielded scraper blade Then clean the hob with Miele ceramic and stainless steel hob cleaner see Optional accessories applied with kitchen paper or a clean cloth Do not apply cleaner whilst the appliance is still hot as this could result in marking Please follow the manufacturer s instructions Finally wipe the hob with a damp cloth then dry with a soft dry cloth Residues can burn onto the appliance the next time itis used and cause damage to the ceramic surface Ensure that all cleaning agent residues are removed Spots caused by limescale water and aluminium residues spots with a metallic appearance can be removed using Miele s ceramic and stainless steel hob cleaner Danger of burning Protect your hands with oven gloves before using a shielded scraper blade to remove sugar plastic or aluminium residues from the hot hob Should any sugar plastic or aluminium foil spill or fall onto a hot cooking zone while it is in use first switch off the appliance Then carefully scrape off all the sugar plastic or aluminium re
43. ooking zone you want m Select a power level if you wish m Touch the B III sensor twice The indicator light for the booster lights up and 1 starts to flash in the display After a few seconds will light up constantly and the indicator light will go out To switch off the Booster TwinBooster 32 m Touch the sensor for selecting the cooking zone you want m Touch the B III sensor until the indicator light for the booster goes out and the cooking zone setting shows in the display or m Touch the sensor for selecting the cooking zone you want m Select a different power level Operation Keeping warm function Each cooking zone has a keeping warm function h The h function is inbetween the 0 setting and the 1 setting This function is for keeping food that has just been cooked warm i e food that is still hot It is not for reheating food that has gone cold If the keeping warm function has been activated the cooking zone will switch off automatically after a maximum of 2 hours To set the keeping warm function m Touch the sensor for selecting the cooking zone you want m Touch the area inbetween the 0 setting and the 1 setting h will light up in the display Useful tips Only use pans for keeping food warm Cover the pan with a lid You do not have to stir food while it is being kept warm Nutrients are lost when food is cooked and this will continue when food is kept warm The lo
44. r level for the cooking zone you require m Touch the sensor repeatedly until the indicator light for this cooking zone flashes If more than one cooking zone is switched on the indicator lights will flash clockwise beginning with the front left zone m Set the time you want The time set will then count down in minutes The time remaining will be shown in the timer display You can change this at any time If you want to set another cooking zone to switch off automatically follow the same steps as described above If more than one switch off time is programmed the shortest time remaining will show in the display and the corresponding indicator light will flash All the other indicator lights will light up constantly If you want to check on the time remaining for another zone touch the sensor repeatedly until the indicator light for the zone you require flashes 37 Timer To use both timer functions at the same time The minute minder and automatic switch off functions can be used at the same time If you have programmed in one or more switch off times and would like to use the minute minder as well Touch the sensor repeatedly until the indicator lights for the cooking zones you have programmed light up constantly and 68 appears in the timer display If you are using the minute minder and would like to programme in one or more switch off times as well Touch the sensor repeatedly until the indicator
45. ronic appliances often contain valuable materials They also contain materials which if handled or disposed of incorrectly could be potentially hazardous to human health and to the environment They are however essential for the correct functioning of your appliance Please do not therefore dispose of it with your household waste Please dispose of it at your local community waste collection recycling centre or contact your dealer for advice Ensure that it presents no danger to children while being stored for disposal Before using for the first time Please stick the extra data plate for the appliance supplied with this documentation in the space provided in the After sales service data plate guarantee section of this booklet Cleaning for the first time m Remove any protective wrapping and adhesive labels m Before using for the first time clean the appliance with a damp cloth only and then wipe dry Before using for the first time On hobs with bevelled glass edges a small gap may be visible between the hob and the worktop during the first few days after installation This gap will reduce with time as the appliance is used and will not affect the electrical safety of your appliance The metal components have a protective coating which may give off a slight smell when heated up for the first time The induction coils may also give off a slight smell for the first few hours of operation This smell will be le
46. sidues from the hob immediately whilst they are still hot using a shielded scraper blade Allow the appliance to cool down and then clean as described above 45 Programming You can change the default settings of the programme options see chart Several settings can be altered in succession After selecting programming mode P Programme and 5 Status will appear in the timer display On hobs with 3 cooking zones an additional indicator will appear at the rear left The programme is shown in the cooking zone displays at the front left and rear left Example Programme 03 front left rear left 3 Programme 14 front left 4 rear left 7 The status is shown in the front right cooking zone display Once you have left the programming mode the hob will be reset automatically This is completed when an indicator above the D sensor lights up briefly Do not switch the hob on again until the reset process is completed To select programming mode m With the hob switched off touch the D and amp sensors at the same time until the safety lock indicator light flashes To set the programme m To set the units position first touch the sensor for selecting the rear left cooking Zone and then touch the relevant number on the numerical keypad m To set the tens position first touch the sensor for selecting the front left cooking Zone and then touch the relevant number on the numerical keypad To set the status
47. ss noticeable with each subsequent use before dissipating completely The smell and any vapours given off do not indicate a faulty connection or appliance and they are not hazardous to health Please note that the heating up time on induction hobs is very much shorter than on conventional hobs 21 Induction The induction principle 22 An induction coil is located under each cooking zone When a cooking zone is switched on this coil creates a magnetic field which impacts directly on the base of the pan and heats it up The cooking zone itself is heated up indirectly by the heat given off by the pan An induction cooking zone only works when a ferromagnetic pan is placed on it see Pans The induction cooking zone automatically recognises the size of the pan The symbol flashes alternately with the power setting selected in one of the cooking zones if it is switched on without a pan in place or if the pan is unsuitable non magnetic base if the diameter of the base of the pan is too small if the pan is taken off the cooking zone when it is switched on If a suitable pan is placed on the cooking zone within 3 minutes the will go out and you can continue as normal If no pan or an unsuitable pan is placed on the cooking zone the cooking zone will switch off automatically after 3 minutes Danger of burning Do not use the hob as a resting place for metal items e g cutlery When the app
48. st 160 C For granite and marble worktops only use silicone sealant that is especially formulated for granite and marble and observe the sealant manufacturer s instructions Flush fitted hobs Solid wood tiled and glass worktops Preparing the worktop Worktop Gap Wooden frame 13 mm to be provided on site As the ceramic glass and the worktop cut out have a certain dimensional tolerance the size of gap can vary min 1 mm m Make the worktop cut out as shown in Building in dimensions Observe the safety distances see Safety instructions for installation m Fix the wooden frame 7 mm below the top edge of the worktop see diagram Connecting the mains cable to the appliance The mains cable must only be connected to the appliance by a qualified and competent electrician in strict accordance with current local and national safety regulations BS 7671 in the Uk m Follow the instructions in the wiring diagram see Electrical connection Wiring diagram Installing the hob m Feed the mains connection cable down through the cut out m Centre the hob in the cut out m Connect the hob to the mains m Check that the hob works m Seal the remaining gap with a silicone sealant that is heat resistant to at least 160 C Observe the silicone sealant manufacturer s instructions For granite and marble tiles only use sil
49. t of any faults which you cannot remedy yourself please contact your Miele dealer or Miele see back of manual for contact details Please note that telephone calls may be monitored and recorded for training purposes UK only When contacting your Dealer or Miele please quote the model and serial number of your appliance These are given on the data plate Space in which to stick the extra data plate supplied with the appliance Ensure that the model number is the same as the one on the back of these instructions Guarantee For information on the appliance guarantee specific to your country please contact Miele See back of manual for contact details In the UK your appliance is guaranteed for 2 years from the date of purchase However you must activate your cover by calling 0845 365 6640 or registering online at www miele co uk 76 77 78 United Kingdom Miele Co Ltd Fairacres Marcham Road Abingdon Oxon OX14 1TW Tel 0845 365 0555 Customer Contact Centre Tel 0845 365 6600 E mail info miele co uk Internet www miele co uk Australia Miele Australia Pty Ltd ABN 96 005 635 398 1 Gilbert Park Drive Knoxfield VIC 3180 Tel 1300 464 353 Fax 03 9764 7149 Internet www miele com au China Miele Shanghai Trading Ltd 1 3 Floor No 82 Shi Men Yi Road Jing an District 200040 Shanghai PRC Tel 86 21 6157 3500 Fax 86 21 6157 3511 E mail info miele cn Internet www miele cn
50. th and then lights up constantly The intermediate setting will be represented by an illuminated dot next to the number 27 Operation Altering the power level m Touch the sensor for selecting the cooking zone you want The power level will flash in the cooking zone display m Set the power level you want by touching the relevant number on the numerical keypad If only one of the cooking zones is in operation you can alter the power level without activating the cooking Zone PowerFlex cooking area The PowerFlex cooking zones can be combined to form a PowerFlex cooking area Settings for the cooking area are controlled by the rear right cooking zone and appears in the display for the front right cooking zone Activating deactivating m Touch the B sensor 28 Operation Auto heat up When Auto heat up has been activated the cooking zone switches on automatically at the highest power setting and then switches to the continued cooking setting selected The heat up time depends on which continued cooking setting has been chosen see chart To activate Auto heat up m Touch the sensor for selecting the cooking zone you want The cooking zone display will flash m Touch the number for the continued cooking setting you want until an audible tone sounds and the indicator light to the right of the continued cooking setting lights up The indicator light to the right of the continued cooking setting will go out
51. then switch itself off automatically 52 Problem solving guide Problem Possible cause Remedy The sensors are over sensitive or do not react at all The sensitivity level of the sensors has changed Make sure that there is no direct light from the sun or from an artificial source falling onto the hob and that the surrounding area is not too dark Make sure that there is nothing covering the sensors or the hob Take any pans off the hob and wipe away any food deposits Interrupt the power supply to the hob for approx 1 minute If this does not solve the problem please call the Miele Service department FE flashes alternately with numbers in the timer display Other fault messages FE The overheating protection mechanism has triggered See Overheating protection The fan is either blocked or faulty Make sure it has not been blocked by something like a fork Remove the cause of the blockage If the fault message appears again call the Miele Service Department There is an electronic fault Interrupt the power supply to the hob for approx 1 minute If the problem persists after reconnecting the appliance to the power supply please contact the Miele Service department 53 Optional accessories Pans Miele offer a comprehensive range of useful accessories as well as cleaning and conditioning products for your Miele appliances
52. top and Go feature which when activated reduces the power of all cooking zones in use to power level 1 When Stop and Go is activated the cooking zone power levels and the setting of the timer cannot be altered and the hob can only be switched off When Stop and Go is deactivated the cooking zones resume at the power level which was last set If Stop and Go is not deactivated the hob switches off after 1 hour When Stop and Go is activated the countdown of a time programmed in for automatic switch off will be interrupted When deactivated the time will continue to run the minute minder will continue without interruption m Touch the Il gt sensor The power of the cooking zones in use will be reduced to power level 1 m Touch the Il gt sensor The cooking zones will now run at the level that was previously set 41 Safety features Safety switch off Safety switch off with an over long cooking time If one of the cooking zones is heated for an unusually long period of time see chart and the power level is not altered the hob will switch itself off automatically and the relevant residual heat indicator will light up To use the cooking zone again switch it back on in the usual way Power level Maximum operating time in hours h 2 kE o eRe 2 2 3 3 414 5 5 6 6 71T D ININ O AH 01 Ol 8 8 9 1 The power levels with a
53. ty lock indicator light flashes After selecting programming mode P Programme and 5 Status will appear in the timer display On hobs with 3 cooking zones an additional indicator will appear at the rear left m Touch the sensor for selecting the front left cooking zone and then touch the 1 on the numerical keypad Set Programme 10 m Touch the sensor for selecting the front right cooking zone and then touch the 1 on the numerical keypad Set Status 1 Signed off The signing off process starts and the number 1 flashes The signing off process will take a few minutes The number 1 will light up constantly when the process has been completed successfully m To save the setting touch the O sensor until all the displays go out m Proceed as described in the Miele home or Con ctivity fitting and installation instructions 59 Safety instructions for installation The appliance must only be installed and connected to the electricity supply by a suitably qualified and competent person in strict accordance with current national and local safety regulations Fit the wall units and extractor hood before fitting the hob to avoid damaging the appliance D The veneer or laminate coatings of worktops or adjacent kitchen units must be treated with 100 C heat resistant adhesive which will not dissolve or distort Any backmoulds must be of heat resistant material This appliance must not be installed over a fridge
54. use rating see data plate There may be a technical fault Disconnect the appliance from the electricity supply for approx 1 minute To do this switch off at the isolator or disconnect the mains fuse Reset the trip switch in the mains fuse box and switch the appliance back on If it still will not switch on contact a qualified electrician or the Miele Ser vice Department 50 Problem solving guide Problem Possible cause Remedy A smell and vapours are given off when a new appliance is being used The smell and vapours will be less noticeable with each subsequent use before dissipating completely The symbol flashes alternately with the power setting selected in one of the cooking zones There is no pan on the cooking zone or the pan is unsuitable Use a suitable pan see Pans After the hob is switched on Lf appears in the timer display for a few seconds The system lock is activated Deactivate the system lock see Safety lock System lock After the hob is switched on dE appears in the timer display for a few seconds The cooking zones do not heat up The appliance is in demonstration mode Deactivate demonstration mode see Programming A cooking zone or the whole hob switches off automatically A cooking zone has been in use for too long You can use the cooking zone again by swit
Download Pdf Manuals
Related Search