Chief XPAUB
Contents
1. Figure 17 Use four 10 24 x 1 2 button head cap X or security screws to secure lower cover D to front of column assembly F See Figure 18 Figure 18 Back of Column 4 Insert tabs on one side of upper cover E into corresponding slots on side of column assembly See Figure 19 Manipulate upper cover E so that it fits within front cavity of column assembly and insert tabs on other side of upper cover E into corresponding slots on side of column assembly See Figure 19 Figure 19 11 XPAU Installation Instructions 6 Insert tabs on one side of lower cover D into corresponding slots on side of column assembly See Figure 20 7 Manipulate lower cover D so that it fits within lower cavity of column assembly and insert tabs on other side of lower cover D into corresponding slots on side of column assembly See Figure 20 0 Figure 20 8 Use six 10 24 1 2 button head X or security Y screws to secure upper cover E and lower cover D to back of column F See Figure 212. 12 Figure 21 Adjustments Height Adjustment 1 Turn height adjustment knob clockwise to raise display See Figure 22 Turn height adjustment knob counterclockwise to lower display See Figure 22 WARNING Do not attempt to raise or lower the adjustment carriage beyond its upper or lower limit High and low points are shown in Figures 22 and 23 NOTE A 1 2 socket wrench or drill may also be used to adjust height by turning bolt just above height adjustment knob height adjustment knob high point low point Figure 23 Installation Instructions XPAU Pitch Adjustment WARNING Removing pitch adjustment screws when the display is installed will result in the display falling from the mount Do NOT remove pitch adjustment screws completely while the display is installed to the mount 3 Loosen pitch adjustment screws to allow pitch to be adjusted See Figure 24 4 Adjust pitch as desired See Figure 24 5 Tighten pitch adjustment screws to lock pitch position See Figure 24 side view OI NS pitch adjustment screws Figure 24 Cart Use and Maintenance WARNING Exceeding the weight capacity can result in serious personal injury or damage to equipment It is the installer s responsibility to make su
3. factory warranty It is the installer s responsibility to make sure all components are properly assembled and installed using the instructions provided WARNING Failure to provide adequate structural strength for this component can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the structure to which this component is attached can support five times the combined weight of all equipment Reinforce the structure as required before installing the component WARNING Exceeding the weight capacity can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the combined weight of all components located between the XPAU up to and including the display does not exceed 300 Ibs 136 kg Use with heavier televisions may result in instability causing tip over resulting in death or serious injury WARNING Exceeding the weight capacity can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the combined weight of all components installed to the vertical rack brackets C does not exceed 20 Ibs 9 07 kg and that the combined weight of all components installed to the accessory bracket G does not exceed 10 Ibs 4 54 kg The combined weight of all components installed to the lower bracket CPU s etc cannot exceed 20 Ibs 9 07 kg Exceeding the weight capacity may result in da
4. open position See Figure 8 8 Hang interface uprights B on head assembly See Figure 8 open position head assembly Figure 8 IMPORTANT In order to ensure an even mount install uprights to be centered over column assembly Do NOT install both uprights to the same side of column assembly See Figure 9 Figure 9 9 Move latches on interface uprights to the closed position to secure display to head assembly See Figure 10 Figure 10 10 Snap four upright covers A onto uprights See Figure 11 NOTE Tabs on inside of covers A will snap directly into holes on uprights to ensure a secure connection column not shown for clarity o Figure 11 11 Optional Use padlocks not provided to secure uprights to head assembly See Figure 11 XPAU Installation Instructions Cable Management NOTE The following cable management options may vary based on type of display being mounted and user preference 1 Usetwo 1 4 20 x 1 2 Phillips pan machine screws L to attach two cable hooks K to bottom of column assembly F See Figure 12 LZ N K x 2 O Y L x 2 Figure 12 2 Place FCA clip U into groove on back of Fusion mount with clip handle in a vertical position See Figure 13 3 Rotate FCA clip U 90 in either direction until clip handle
5. INSTALLATION INSTRUCTIONS Extra Large Height Adjustable Video Cart S CHIEF XPAU Our Mounts Your XPAU Installation Instructions DISCLAIMER Milestone AV Technologies and its affiliated corporations and subsidiaries collectively Milestone intend to make this manual accurate and complete However Milestone makes no claim that the information contained herein covers all details conditions or variations nor does it provide for every possible contingency in connection with the installation or use of this product The information contained in this document is subject to change without notice or obligation of any kind Milestone makes no representation of warranty expressed or implied regarding the information contained herein Milestone assumes no responsibility for accuracy completeness or sufficiency of the information contained in this document Chief is a registered trademark of Milestone AV Technologies All rights reserved A IMPORTANT SAFETY INSTRUCTIONS WARNING A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions CAUTION A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the corresponding instructions WARNING Failure to read thoroughly understand and follow all instructions can result in serious personal injury damage to equipment or voiding of
6. Removing Display from Cart 1 Remove any padlocks from interface uprights if installed 2 Position latches on interface uprights so that they are in the open position See Figure 27 WARNING DISPLAYS MAY WEIGHT IN EXCESS OF 40 LBS Always use two people and proper lifting techniques when installing or positioning display on cart 3 Carefully lift display from cart See Figure 27 open position Figure 27 14 Installation Instructions XPAU 15 XPAU Installation Instructions GS CHIEF Our Mounts Your Vision Chief Manufacturing a products division of Milestone AV Technologies 8800 002446 Rev02 2013 Milestone AV Technologies a Duchossois Group Company www chiefmfg com 10 13 USA International Europe Asia Pacific gt TU 6436 City West Parkway Eden Prairie MN 55344 800 582 6480 952 225 6000 877 894 6918 952 894 6918 Franklinstraat 14 6003 DK Weert Netherlands 31 0 495 580 852 31 0 495 580 845 Office No 1 on 12 F Shatin Galleria 18 24 Shan Mei Street Fotan Shatin Hong Kong 852 2145 4099 852 2145 4477 SCH 52 d D
7. Serrez les fixations Pencil Mark Marcar con l piz Stiftmarkierung Marcar com l pis Segno a matita Potloodmerkteken Marquage au crayon Loosen Fastener Aflojar elemento de fijaci n Befestigungsteil l sen Desapertar fixador Allentare il fissaggio Bevestiging losdraaien Desserrez les fixations Drill Hole Perforar Bohrloch Fazer furo Praticare un foro Gat boren Percez un trou Phillips Screwdriver Destornillador Phillips Kreuzschlitzschraubendreher Chave de fendas Phillips Cacciavite a stella Kruiskopschroevendraaier Tournevis pointe cruciforme Adjust Ajustar Einstellen Ajustar Regolare Afstellen Ajuster Open Ended Wrench Llave de boca Gabelschl ssel Chave de bocas Chiave a punte aperte Steeksleutel Cl fourche Remove Quitar Entfernen Remover Rimuovere Verwijderen Retirez By Hand A mano Von Hand Com a m o A mano Met de hand la main Optional Opcional Optional Opcional Opzionale Optie En option SY A amp DO CY Hex Head Wrench Llave de cabeza hexagonal Sechskantschl ssel Chave de sextavada Chiave esagonale Zeskantsleutel Cl
8. is in a horizontal position See Figure 13 4 Repeat Steps 2 3 for all clips to be installed clip handle Figure 13 10 5 Route cables along FCA clips to be used for cable management See Figure 14 6 Use cable ties V to secure cables to FCA clips See Figure 14 Figure 14 7 Route cables from display through inside of column assembly attaching at cable management attachment points and or accessory bracket as desired See Figure 15 IMPORTANT Route cables when display is at its highest point and make sure enough slack exists so that height may be adjusted without straining the cables clips underneath Figure 15 Installation Instructions XPAU 8 Wrap cables around cable hooks K as desired See Figure 16 Figure 16 Covers Installation Front of Column 1 Insert tabs on one side of lower cover D into corresponding slots on side of column assembly See Figure 17 Manipulate lower cover so that it fits within front cavity of column assembly and insert tabs on other side of lower cover into corresponding slots on side of column assembly See Figure 17
9. ll is used to insert button head cap screws Screws should first be inserted and turned BY HAND with the hex key or with a hand held screwdriver BEFORE using the hex head drill bit and power drill to complete the attachment Cart Assembly 1 Carefully set column assembly F on its left side See Figure 1 2 Place right transition cover on right cart leg J lining up the holes on the cover with the holes on the leg and column assembly base See Figure 1 3 Use two 5 16 18 x 3 3 4 button head cap screws R to secure leg J and cover P to column assembly F See Figure 1 rear view Figure 1 4 Turn column assembly onto its right side See Figure 2 5 Place left transition cover N on left cart leg H lining up the holes on the cover with the holes on the leg and column assembly base See Figure 2 6 Use two 5 16 18 x 3 3 4 button head cap screws R to secure leg H and cover N to column assembly F See Figure 2 2 0 Figure 2 Accessory Bracket Installation Optional NOTE Accessory bracket may be installed to either side of column 1 Loosely install two 10 24 x 3 8 Phillips head machine screws M through two 10 washers AA holes in accessory bracket 0 and into two 10 24 square nuts 2 See Figure 3 2 Insert two 10 24 square nuts Z into two openings column channel See Figure 3 3 Lif
10. mage to equipment It is the installer s responsibility to make sure the combined weight of all components installed to the lower bracket does not exceed 20 lbs 9 07 kg Exceeding the weight capacity may result in damage to the equipment or components NOTE CPU strap is designed for use with larger non rack mountable CPU s or audio video components 22 hole on lower bracket CPU example Figure 5 Vertical Rack Bracket Installation Optional NOTE Vertical rack brackets C are intended for use with 4 various types of rack mountable products Loosely install two 10 24 x 3 8 Phillips head machine screws M through two 10 washers AA holes in vertical rack bracket C and into two 10 24 square nuts 2 See Figure 6 Insert two 10 24 square nuts Z into two openings on column channel See Figure 6 Lift vertical rack bracket C to desired mounting position See Figure 6 Tighten screws to secure in position See Figure 6 IMPORTANT Do NOT attach rack brackets higher than 22 above the base extrusion or they could interfere with the height adjustment mechanism See Height Adjustment Section for details 5 Repeat Steps 1 4 on other side for other bracket 6 Figure 6 WARNING Exceeding the weight capacity can result in serious personal injury or damage to equipment It is the installer s responsibility to make s
11. mage to the equipment or components WARNING Use this mounting system only for its intended use as described in these instructions Do not use attachments not recommended by the manufacturer WARNING Never operate this mounting system if it is damaged Return the mounting system to a service center for examination and repair WARNING Do not use this product outdoors WARNING RISK OF INJURY TO PERSONS Do not place video equipment such as televisions or computer monitors on cart legs WARNING RISK OF SERIOUS INJURY OR DEATH Placing a remote control or toy on the cart may encourage a child to climb onto the cart causing the cart to tip over onto the child DO NOT place remote controls or toys on the cart WARNING RISK OF SERIOUS INJURY OR DEATH Relocating audio and or video equipment to the cart may result in the cart collapsing or overturning onto a child DO NOT relocate audio and or video equipment to the cart NOTE The XPAU cart has no user serviceable parts NOTE The XPAU cart can support screen sizes up to a maximum of 100 SAVE THESE INSTRUCTIONS Installation Instructions XPAU DIMENSIONS T 87 200 W IN 31 50 800 N 41 XPAU Installation Instructions LEGEND Tighten Fastener Apretar elemento de fijaci n Befestigungsteil festziehen Apertar fixador Serrare il fissaggio Bevestiging vastdraaien
12. re the combined weight of all components located between the XPAU up to and including the display does not exceed 300 105 136 kg WARNING RISK OF SERIOUS INJURY OR DEATH Placing a remote control or toy on the cart may encourage a child to climb onto the cart causing the cart to tip over onto the child DO NOT place remote controls or toys on the cart WARNING RISK OF SERIOUS INJURY OR DEATH Relocating audio and or video equipment to the cart may result in the cart collapsing or overturning onto a child DO NOT relocate audio and or video equipment to the cart WARNING CART CAN TIP OVER RESULTING IN INJURY Do not allow children under 16 to move cart Only adults should move this cart Move cart slowly Apply moving force on narrow dimension Never apply force at top always push toward the middle Push don t pull cart See Figure 25 NOTE The XPAU cart has no user serviceable parts NOTE The XPAU cart can support screen sizes up to a 1 maximum of 100 wide Always place cart on a level surface Do NOT push cart near top lt Push cart near middle Figure 25 13 XPAU Installation Instructions Always lock the wheels when the cart is not moving Check tighten the hex nuts on the casters occasionally See Figure 26 These should be checked especially after use on uneven ground x4 Figure 26
13. red H mounting holes are recessed or if protrusions prevent uprights B from laying flat then spacers TL or TM must be used Using your hand insert SHORTEST length screw of selected diameter TA TD TG or TI through universal washer TN uprights B selected spacer TL or TM into display mounting hole Do NOT thread screw into hole at this time NOTE Universal washers TN are not needed if using M8 button head cap screws TI TJ or e Proper screw length requires base of screw head to protrude above flat washer a distance equal to or greater than the screw diameter screw length is inadequate select longer screw Select shortest screw which will protrude the required distance Place uprights B on display ensuring See Figure 7 e Center of uprights are as close the center of the back of display as possible after being installed Center of bracket is indicated by the diamond shaped hole Use selected screws and spacers to install two interface uprights B to back of display See Figure 7 mam Bet AE Figure 7 Installation Instructions XPAU WARNING Display may be very heavy Ensure display may be safely lifted and maneuvered as required to install on cart Failure to take adequate precautions can result in serious personal injury or damage to equipment 7 Position latches on interface uprights so that they are in the
14. t te hexagonale 80 Security Wrench Llave de seguridad Sicherheitsschl ssel Chave de seguranga Chiave di sicurezza Veiligheidssleutel Cl de s curit Installation Instructions XPAU TOOLS REQUIRED FOR INSTALLATION 1 8 included 5 included 3 16 included 5 32 included security Ze PARTS T 1 N Hardware bag A 4 ISS 2 e B 2 Vertical rack 9 M4x16mm M4x20mm M4x25mm 2 bracket 3 Interface upright P e e TD 6 TE 6 TF 6 M5x16mm M5x20mm M5x25mm Col i 1 1 olumn lower I 1 e cover SS Column assembly Y 22 e SN J 1 TG 6 TH 6 Right cartleg amp M6x16mm 2 lt K 2 lt Cable hook LD ee gd H 1 G 1 Left cart leg H TK 4 Accessory bracket L 2 M8x30mm 8 50 1 4 20 x 1 2 y AS Se 27 ne 10 24 x 3 8 Left transition cover _ P 1 1 4 1 2 Right transition cover 3 22 20 10 W 1 R 4 U 10 Cable tie CEU 5 16 18 3 3 4 FCA clip SR NN Y e BB 1 CC 1 DD 1 Y 10 5 32 3 16 1 8 1 Se 1 2 10 24 x 1 2 si i 6 security security XPAU Installation Instructions Assembly And Installation CAUTION Attachment holes may be damaged if a power dri
15. t accessory bracket to desired mounting position See Figure 3 4 Tighten screws to secure in position See Figure 3 A Ee 2 3 2 IN N H ib H Y S 3 y gt Go 22 Figure 3 Installation Instructions XPAU WARNING Exceeding the weight capacity can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the combined weight of all components installed to the accessory bracket G does not exceed 10 105 4 54 kg Exceeding the weight capacity may result in damage to the equipment or components IMPORTANT Do NOT attach accessory bracket too high on column or above height adjustment mechanism or it could interfere with the height adjustment mechanism See Height Adjustment Section for details 5 Install components to accessory bracket as desired using cable ties V or screws See Figure 4 NOTE Accessory bracket is designed to mount small audio video components such as power strips media players etc power strip example Figure 4 CPU Installation Optional 1 Route CPU strap Q through hole on lower bracket and around CPU to secure CPU to column base See Figure 5 WARNING Exceeding the weight capacity can result in serious personal injury or da
16. ure the combined weight of all components installed to the vertical rack brackets C does not exceed 20 lbs 9 07 kg Exceeding the weight capacity may result in damage to the equipment or components Install rack mountable components to vertical rack brackets C as desired using standard rack screws not included XPAU Installation Instructions Display Installation CAUTION Using screws of improper length may damage your display Proper screws will have adequate thread engagement without contacting bottom of display mounting holes WARNING Exceeding the weight capacity can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the combined weight of all components located between the XPAU up to and 4 Select screw length See Figure 7 including the display does not exceed 300 105 136 kg Use with heavier televisions may result in instability causing tip over resulting in death or serious injury 1 Lay display face down on protective surface CAUTION Using screws of improper diameter may damage your display Proper screws will easily thread into display mounting holes 2 Select screw diameter by examining hardware TA TK 4mm 5mm 6mm or 8mm and comparing with mounting holes on display See Figure 7 3 Select spacers See Figure 7 H mounting holes are not recessed and both uprights B can lay flat against display then no spacers are requi
Download Pdf Manuals
Related Search