RCA RCR313BR remote control
Contents
1. Universal Remote Control Owner s Manual RCR314WR RCR313BR Manual del Propietario parte posterior FCC Statement This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Note This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for2. Press POWER on the remote and wait 2 seconds The remote is testing a single code for your device s brand 7 22 Did your device turn off YES Press the STOP key to store the code You re done You ve programmed this device key NO Press POWER again The remote tests the next code for your brand Keep pressing POWER every 2 seconds until your device turns off When it does press STOP NOTES Throughout the programming of each key be sure to keep the remote pointed at the IR sensor of the device you are currently programming the remote to control Test the remote with the device to make sure the device key is programmed with the correct code for maximum functionality If some features don t work try a different code See the Testing the Code for Maximum Functionality section below for more information During the Brand Code Search the remote ignores keypresses that aren t part of the search The search times out after two minutes the POWER key blinks four times and turns off and the last programmed code under that device key is retained The POWER key blinks four times and turns off when the remote has gone through all the codes The remote exits the Brand Code Search If your device hasn t turned off yet try a different search method Testing the Code for Maximum Functionality 1 Try a variety of the device s functions with the remote If some device features don t work go to the next step t
3. help Caution Any Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate this equipment Industry Canada Regulatory Information This class B digital apparatus complies with Canadian ICES 003 Avis d industrie Canada Cet appareil num rique de la classe B est conforme a la nome NMB 003du Canada SAVE THIS MANUAL AND THE CODE LISTS Remote controls can sometimes lose their programming when you change the batteries Make sure you keep the manual and code lists in a safe place so that you can reprogram the remote if you need to Congratulations on your purchase of this 3 device RCA Universal Remote Control This remote features a library of codes with the latest devices of all major brands with support for streaming media players as well The navigation keys have been redesigned to function seamlessly with the more sophisticated menu and guide systems found in today s home entertainment devices Step 1 Install your batteries Your universal remote requires two AA alkaline batteries batteries may or may not be included depending on model To install the batteries 1 Remove the battery compartment cover 2 Insert the batteries matching the batteries to the and marks inside the battery compartment 3 Push the battery cover back into place Battery Precautions e Do not mix old and new batteries e Do not mix alkaline stand
4. key to control VCR or DVD Test the remote with the device to make sure the device key is programmed with the correct code for i irs LS einai hey ss ae a MONG maximum functionality If some features don t work try eee anes esp tae Nae ee iE a ie a different code See the Testing the Code for Maximum i Y YP y Functionality section below for more information control with this key 2 for VCR 3 for DVD During the Auto Code Search the remote ignores keypresses that aren t part of the search The search times out after two minutes the POWER key blinks four times and turns off and the last programmed code under that device key is retained The POWER key blinks four times and turns off when the remote has gone through all the codes The remote exits the Auto Code Search If your device hasn t turned off yet try a different search method Testing the Code for Maximum Functionality 3 Press and hold the device key you want to program 1 Try a variety of the device s functions with the remote While you re holding down the device key use your If some device features don t work go to next step to other hand to press and hold the remote s POWER key try a different code at the same time 2 Repeat the Auto Code Search Method from the beginning When your device turns off do not stop searching Instead with the unit now off continue to press the PLAY key every 5 seconds until the unit turns back on 3 Once
5. the unit turns back on press the REVERSE key on the remote every 2 seconds until your device turns off again When your device turns off again press the 4 Wait until the POWER key comes on and stays on STOP key VOL A CHAN Then release both keys 4 Test the key s functionality again by attempting to control a variety of the device s functions If the code that has been stored controls the majority of the 5 Point the remote directly at the eae fat lof the devi Te device s functions programming is complete If the ront panel of the device you Be want to control Press PLAY on the remote and wait 5 seconds The remote is testing a batch of 10 codes on your device code stored does not give maximum functionality try another code Manual Code Search The Manual Code Search lets you go one by one through all the codes for the device you re trying to control When you find the one that operates your device you can stop the search and store that code Did your device turn off YES Go to step 6 NO Press PLAY again The remote tests the next batch of 10 codes TIPS Each device key is associated with a type of device the TV is preset to search for TVs SATeCBLeSTREAM for satellite receivers cable boxes digital TV converters or streaming media players and DVDeVCR for VCRs or DVD players Keep pressing PLAY every 5 seconds until your device turns off The POWER key serves as
6. Replace the batteries with two new AA batteries if necessary see the Battery Installation section Problem The remote can t be programmed to operate your device e If you are testing the remote while programming it you may be too far away from the device or at a wrong angle There must be an unobstructed path between the remote and the IR sensor on the device Move closer and make sure you point the remote at the device you re trying to control If you re using the Direct Entry programming method to enter the codes for your brand and the unit is still not functioning properly try the auto brand or manual search method To control combo units like TV VCRs or TV DVDs you must program the individual corresponding device keys to control each part of the combo unit Once programmed successfully the TV key controls the TV functions and the DVDeVCR key controls the VCR or DVD functions Make sure the batteries are fresh and are properly installed Problem The remote doesn t perform commands properly e Make sure the remote is in the correct mode by pressing the corresponding device key TV SATeCBLeSTREAM DVDeVCR This tells the remote which device to operate Make sure device is ready for example the DVD player has a disc loaded You may have pressed an invalid key for the mode the remote is in If you re trying to enter a channel number directly try pressing the OK key after entering the channel number as thi
7. an indicator light during programming giving you feedback at each stage of the process The Manual Code Search method may take a long time because the remote searches through all of the codes in its memory one by one If your brand is listed in the Brand Codes or the Code Lists first try the Brand Code Search or the Direct Code Entry method To exit without saving a new code at any point in the Manual Code Search press the GO BACK key 1 Manually turn on the device you want to control POWER 2 If you re programming the TV or SATeCBLeSTREAM key go to step 3 If you re programming the DVDeVCR key you need to tell the remote which kind of device you want this key to control VCR or DVD Press and hold the DVDeVCR key While you re holding down the DVDeVCR key use your other hand to press the number key for the type of device you want to control with this key 2 for VCR 3 for DVD 3 Press and hold the device key you want to program While you re holding down the device key use your other hand to press and hold the remote s POWER key at the same time 4 Wait until the POWER key comes on and stays on Then release both keys 5 Point the remote directly at the front panel of the device you want to control Press POWER on the remote and wait 2 seconds The remote is testing a single code for your device Did your device turn off the code You re done You ve programmed this
8. ard carbon zinc or rechargeable nickel cadmium batteries e Always remove old weak or worn out batteries promptly and recycle or dispose of them in accordance with Local and National Regulations Battery Saver Your universal remote control saves battery power by automatically turning off if any key is pressed for more than 60 seconds This saves your battery life should your remote get stuck in a place where the keys remain depressed such as between sofa cushions Step 2 Program your remote To use this universal remote with your home entertainment system first you need to program it to control your devices There are four ways you can program the universal remote to operate your devices Try them in the order listed here The Brand Code Search searches through the codes for select brands of devices The Direct Code Entry lets you enter a code from the accompanying code list for your brand of device The Auto Code Search goes automatically through all the codes for the device you re trying to control The Manual Code Search lets you manually go through all the codes for the device you re trying to control Brand Code Search The Brand Code Search goes through only the codes for one of the select brands listed in the accompanying code list If your brand of device is listed this search can be very quick and easy TIPS Each device key is associated with a type of device the TV is preset to search for TVs SAT
9. ber that causes the POWER key to blink is the first number of the code As you find each number of the code write it down for future reference Note All TV codes begin with the number 1 all VCR and DVR codes begin with the number 2 all DVDs the number 3 and all satellite receivers cable boxes streaming players and DTV converters the number 5 5 Repeat step 4 until you have retrieved all five numbers in the code After the fifth number is retrieved the POWER key blinks briefly then turns off TIP To exit the Code Retrieval Mode at any time press the GO BACK key Note If you press an invalid key during the Code Retrieval process the remote will not respond If you do not press a valid Code Retrieval key TV SATeCBLeSTREAM DVDeVCR INFO OPTIONS GO BACK Code Retrieval times out after 15 seconds The POWER key blinks four times and then turns off TV CODE SAT CBL STREAM CODE I Ve SAT CABLE _ DTV CONVERTER L STREAMING PLAYER DVD VCR CODE ULL Llpvp LJvcr Troubleshooting Problem The remote does not operate your device e Make sure the remote is in the correct mode by pressing the corresponding device key TV SATeCBLeSTREAM DVDeVCR This tells the remote which device to operate Remove any obstacles between the remote and the device Make sure you re aiming the remote at the device s IR sensor Make sure the batteries are fresh and are properly installed
10. ct as channel and volume controllers The CHAN keys also provide skip forward and skip back control for DVD players and DVRs that support this functionality GO BACK exits remote programming it also performs the same functions as on your original remotes The INPUT and dash key has three functions 1 it toggles through all the video sources connected to your TV 2 when the remote is in VCR mode this button toggles between VCR and the TV input 3 when you re entering digital channel numbers directly this button lets you separate the main channel number from the sub channel number such as 59 1 IMPORTANT Because this remote controls more than one device you must first tell the remote which device you wish to operate That means if you wish to operate your TV you must first press the TV key to put the remote in the TV Mode The remote stays in that device mode until you press a different device key For example if your remote is in TV Mode and you want to operate the DVD player you must press the DVDeVCR key to change device modes Backlighting Backlight illumination helps you see the remote control keys better in the dark You can turn backlight illumination on or off by pressing the LIGHT key Backlighting stays on as long as keys are being pressed and turns off six seconds after the last keypress Once the backlight time has timed out any keypress will reactivate it If the backlight illumination i
11. defect s will be repaired or replaced at the Company s option without charge for parts and repair labor To obtain repair or replacement within the terms of this Warranty the product is to be delivered with proof of warranty coverage e g dated bill of sale specification of defect s transportation prepaid to the Company at the address shown below This Warranty does not cover product purchased serviced or used outside the United States or Canada This Warranty is not transferable and does not extend to costs incurred for installation removal or reinstallation of the product This Warranty does not apply if in the Company s opinion the product has been damaged through alteration improper installation mishandling misuse neglect accident or the simultaneous use of different battery types e g alkaline standard or rechargeable THE EXTENT OF THE COMPANY S LIABILITY UNDER THIS WARRANTY IS LIMITED TO THE REPAIR OR REPLACEMENT PROVIDED ABOVE AND IN NO EVENT SHALL THE COMPANY S LIABILITY EXCEED THE PURCHASE PRICE PAID BY PURCHASER FOR THE PRODUCT This Warranty is in lieu of all other express warranties or liabilities ANY IMPLIED WARRANTIES INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE SHALL BE LIMITED TO DURATION OF THIS WARRANTY IN NO CASE SHALL THE COMPANY BE LIABLE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES WHATSOEVER No person or representative is authorized to assume for the Com
12. device key NO Press POWER again The remote tests the next code for your device Keep pressing POWER every 2 seconds until your device turns off When it does press STOP TIP Because there are so many codes you may have to press the POWER key many times possibly hundreds of times YES Press the STOP key to store NOTES Throughout the programming of each key keep the remote pointed at the IR sensor of the device you are programming the remote to control Test the remote with the device to make sure the device key is programmed with the correct code for maximum functionality If some features don t work try a different code See the Testing the Code for Maximum Functionality section below for more information During the Manual Code Search the remote ignores keypresses that aren t part of the search The search times out after two minutes the POWER key blinks four times and turns off and the last programmed code under that device key is retained The POWER key blinks four times and turns off when the remote has gone through all the codes The remote exits the Manual Code Search If your device hasn t turned off yet try a different search method Testing the Code for Maximum Functionality 1 Try a variety of the device s functions with the remote If some features of your devices don t work go to the next step to try a different code Repeat the Manual Code Search from the beginnin
13. eCBLeSTREAM for satellite receivers cable boxes digital TV converters or streaming media players and DVDeVCR for VCRs or DVD players The POWER key serves as an indicator light during programming giving you feedback at each stage of the process To exit without saving a new code at any point in the Brand Code Search press the GO BACK key 1 Manually turn on the device you want to control POWER 2 If you re programming the TV or 3 Find your device s brand in the SATeCBLeSTREAM key go to step 3 If you re programming the DVDeVCR key you need to tell the remote which kind of device you want this key to control VCR or DVD Press and hold the DVDeVCR key While you re holding down the DVDeVCR key use your other hand to press the number key for the type of device you want to control with this key 2 for VCR 3 for DVD Brand Code list section of the accompanying code list Circle the number for your brand and keep the list handy 4 Press and hold the device key you want to program While you re holding down the device key use your other hand to press and hold the remote s POWER key at the same time VOL EA CHAN 5 Wait until the POWER key comes on and stays on Then release both keys 6 Look at the number you circled for your device s brand code number Press that number on the remote keypad 7 Point the remote directly at the front panel of the device you want to control
14. g When the device turns off for the first time don t press the STOP key which would store the same code Instead with the unit now off continue to press the POWER key repeatedly until the unit turns back on Once the unit turns back on you have found another code that operates the device Press the STOP key Test the key s functionality again by trying a variety of functions If the code controls the majority of the device s functions programming is complete If the code stored does not give maximum functionality try another code Tour of the Remote In most cases the keys on this remote perform the same functions as the keys on your original remotes once you ve programmed this remote to operate your components Many keys on this remote have other functions as well Illuminated POWER key serves as an indicator light to provide feedback Device keys TV SAT CBL STREAM DVD VCR put the remote in the right mode to control your device LIGHT key Q turns backlighting on off GUIDE HOME and MENU access the same features as the keys on your Original remotes Arrow keys act as navigation keys for streaming media players as well as in menu and guide systems for other devices SAT CBL STREAM TV DVD VCR I MUTE OPTIONS MENU LIGHT O GUIDE SHOME REVERSE PLAY FORWARD 9 0 wW RECORD STOP PAUSE Actual model may vary from illustration CHAN and VOL keys a
15. ircle the codes for your brand and keep them handy 3 Press and hold the device key you want to program the POWER key comes on While you re holding down the device key use your other hand enter the first five digit code for your brand in the code list the POWER key goes off after the first digit 4 When you ve finished entering the five digit code keep holding down the device key and look at the POWER key Is the POWER key on YES You re done You ve programmed this device key NO it blinked four times and turned off You have either entered a code number that is not in the code lists or missed a step in the code entry procedure Iry step 3 again NOTES Remember to enter the code for future reference in the box provided in the Code Retrieval section of this manual If your brand isn t listed in the code list use one of the Code Search methods to program the remote control Refer to the Auto and Manual Code Search methods If you release the device key any time during the Direct Code Entry procedure the POWER key blinks four times and the process is exited The last programmed code under the device key is retained Test the remote with the device to make sure the device key is programmed with the correct code for maximum functionality If some features don t work try a different code in the list Auto Code Search 6 When your device turns off press The Auto Code Search goes automatically thr
16. les between the remote and the device Make sure to aim the remote at the IR sensor on the device Problem The device s menu does not appear on the TV screen Make sure you have connected the device to your TV properly and selected the correct input See your devices Owner s Manuals for proper connection procedures e Make sure the remote is in the correct mode by pressing the corresponding device key TV SATeCBLeSTREAM DVDeVCR This tells the remote which device to operate e Menu access isn t supported for all brands You may need to use your original remote control to access menu functions for some devices For more information please visit www RCAAudioVideo com Consumer Help Line 1 800 420 7968 Care and Maintenance e Keep the remote dry If it gets wet wipe it dry immediately e Use and store the remote only in normal temperature environments e Handle the remote gently and carefully Don t drop it e Keep the remote away from dust and dirt e Wipe the remote with a damp cloth occasionally to keep it looking new e Modifying or tampering with the remote s internal devices can cause malfunction and invalidate its warranty Limited Lifetime Warranty VOXX Accessories Corporation the Company warrants to you the original retail purchaser of this product that should it under normal use and conditions be proven defective in material or workmanship during its lifetime while you own it such
17. o try a different code 2 Repeat the Brand Code Search from the beginning When the device turns off for the first time don t press the STOP key which would store the same code Instead with the unit now off continue to press the POWER key repeatedly until the unit turns back on 3 Once the unit turns back on you have found another code that operates the device Press the STOP key 4 Test the key s functionality again by attempting to control a variety of the device s functions If the code that has been stored controls the majority of the device s functions programming is complete If the code stored does not give maximum functionality try another code Direct Code Entry Direct Code Entry lets you enter a code from the accompanying code list for your brand of device It s not as easy as the other methods but it s potentially the fastest method TIP Each device key is associated with a type of device the TV is preset to search for TVs SATeCBLeSTREAM for satellite receivers cable boxes digital TV converters or streaming media players and DVDeVCR for VCRs or DVD players The POWER key serves as an indicator light during programming giving you feedback at each stage of the process 1 Manually turn on the device you want to control POWER 2 Find the Code List that came with the remote Locate the section for the type of device you re trying to program and find your brand in that section C
18. ough all the the REVERSE key on the remote z codes for the device you re trying to control When you find and wait at least 2 seconds the one that operates your device you can stop the search The remote tries the last of the and store that code previous ten codes Did your device turn on TIPS Each device key is associated with a type YES Press the STOP key You re of device the TV is preset to search for TVs done You ve programmed this SATeCBLeSTREAM for satellite receivers cable boxes device key digital TV converters or streaming media players and DVDeVCR for VCRs or DVD players 7 ee ee NO Press REVERSE again The remote tests the next o exit without saving a new code at any point in the Auto Code Search press the GO BACK key code in the batch Keep pressing REVERSE every 2 seconds until your device turns back on When it does press STOP 1 Manually turn on the device you want to control Note If you accidentally press the REVERSE key after POWER your device turns on press the FORWARD key Then wait two seconds to see if your device turns off again Te NOTES 2 If you re programming the TV or SAT CBLeSTREAM key go to step 3 Throughout the programming of each key be sure to keep the remote pointed at the IR sensor of the device If you re programming the DVDeVCR key you need you are currently programming the remote to control to tell the remote which kind of device you want this
19. pany any liability other than expressed herein in connection with the sale of this product Some states provinces do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damage so the above limitations or exclusions may not apply to you This Warranty gives you specific legal rights and you may also have other rights which vary from state province to state province U S A Audiovox Return Center 150 Marcus Blvd Hauppauge New York 11788 CANADA Audiovox Return Center c o Genco 6685 Kennedy Road Unit 3 Door 16 Mississauga Ontario L5T 3A5 2013 Voxx Accessories Corp 3502 Woodview Trace Suite 220 Indianapolis IN 46268 Trademark s Registered RCR314WR US 04
20. s is a requirement of certain models and brands e There is a possibility that a programmed code may only be able to control some of your device features for example only turns a device on and off To confirm that the device key is programmed with the correct code for maximum functionality test the device Attempt to control a variety of the device s functions with the remote If some of the features of your devices don t work try programming the remote with a different code in the list using the Direct Code Entry Method until you find the code that allows the remote to control the majority of your device s functions Different codes can provide different levels of functionality Problem The POWER key does not light when you press a key e You may have pressed an invalid key for the mode the remote is in e Make sure the remote is in the correct mode by pressing the corresponding device key TV SATeCBLeSTREAM DVDeVCR This tells the remote which device to operate e Make sure the batteries are fresh and are properly installed Replace the batteries with two new AA batteries if necessary see the Battery Installation section Problem The remote will not change channels on device Make sure the remote is in the correct mode by pressing the corresponding device key TV SATeCBLeSTREAM DVDeVCR This tells the remote which device to operate e Press the OK key after you enter a channel number e Remove any obstac
21. s on and you press the backlight key the backlight turns off Advanced Functions Code Retrieval Once you ve programmed the remote to control your devices you may want to record the codes for future reference If you used the Direct Code Entry method this is easy Just find the codes you entered and make a note of them in the boxes below If you used one of the Code Search methods to program your remote or if you used the Direct Entry method but don t remember the code you will need to retrieve each device s five digit code Retrieving the actual code and writing it down will save you time if you ever need to program the remote again e g if programming is lost when you change the batteries If the codes are recorded you can use the Direct Entry method to reprogram your remote to control your devices which is quick and easy POWER key 1 Press and hold the device key TV SATe CBLeSTREAM DVDeVCR whose code you _ wish to retrieve The POWER key turns on Keep pressing the device key SAT CBL STREAM TV DVD VCR INFO MUTE OPTIONS MENU LIGHT 2 While holding the device key down press and hold the INFO OPTIONS key The POWER key turns off After holding down both keys for three seconds the POWER key turns back on 3 Release both keys The POWER key remains on Starting with the number 1 key press and release each number key on the keypad in the following order 1 9 then 0 The num
Download Pdf Manuals
Related Search