Hotpoint WMYL 641P
Contents
1. flash and a sound alert 3 beeps the function will not be activated If a function which is incompatible with another function selected previously only the most recent selection will remain active Starting a wash cycle B Door locked indicator light If this indicator light is on the appliance door is locked to prevent it from being opened accidentally to avoid any damage wait for the indicator light to switch off before you open the appliance door If the START PAUSE indicator light orange flashes rapidly at the same time as the function indicator light this indicates a problem has occurred see Troubleshooting 1 Turn the washing machine on by pressing the ON OFF button All the indicator lights will turn on for a few seconds then only the indicator lights relative to the selected programme settings will remain lit and the START PAUSE indicator light will flash Load the laundry and close the door Set the WASH CYCLE knob to the desired programme Set the washing temperature see Personalisation Set the spin speed see Personalisation Select the desired functions AN OA FW PD manner in green Measure out the detergent and washing additives see Detergents and laundry Start the wash cycle by pressing the START PAUSE button and the corresponding indicator light will remain lit in a fixed To cancel the set wash cycle pause the machine by pressing the START PAUSE butt2. garments with resistant colours It ensures a washing class that is higher than the standard class A class When running the programme do not mix garments of different colours We recommend the use of powder detergent Pre treatment with special additives is recommended if there are obstinate stains Whites use this cycle 2 to wash white clothes The pro gramme is designed to maintain the brightness of white clothes over time Use powder detergent for best results 12 Cotton Standard 20 use this cycle 5 for lightly soiled cotton loads The effective performance levels achieved at cold temperatures which are comparable to washing at 40 are guaranteed by a mechanical action which opera tes at varying speed with repeated and frequent peaks Anti Allergy use programme 7 to remove major allergens such as pollen mites cat s and dog s hair Baby use the special wash cycle 8 to remove the soiling typically caused by babies while removing all traces of detergent from nappies in order to prevent the delicate skin of babies from suffering allergic reactions The cycle has been designed to reduce the amount of bacteria by using a greater quantity of water and optimising the effect of special disinfecting additives added to the detergent Bed amp Bath use programme 9 to wash bed linen and to wels in one single cycle it optimises softener performance and helps you save time and energy We recommend the use of powder detergent
3. Shirts use the special 12 wash cycle to wash shirts in different fabrics and colours to guarantee they receive the best possible care Wool the wool wash cycle on this Hotpoint machine has been tested and approved by The Woolmark Company for washing wool garments labelled as hand washable provided that the garments are washed according to the instructions on the garment label and those issued by the manufacturer of this washing machine Hotpoint is the first washing machine brand to be approved by The Woolmark Company for Apparel Care Platinum for its washing per formance and consumption of energy and water M1126 WOOLMARK APPAREL CARE Delicates use programme 14 to wash very delicate garments with decorative features such as diamantes and sequins We recommend turning the garments inside out before washing and placing small items into the special bag for washing delicates Use liquid detergent on delicate garments for best results To wash silk garments and curtains select cycle 14 and then function Easy Iron in this case it will also be possible to enable the Extra Rinse option the machine will end the cycle while the laundry is soaking the Easy Iron and TTART PAUSE indicator lights will flash orange and the RINSE phase will remain lit in a fixed manner To drain the water so that the laundry may be removed press the START PAUSE button or the Easy Iron button Load balancing system Before eve
4. cover re fitted If the fuse cover is lost the plug must not be used until a replacement is obtained Replacement fuse covers If a replacement fuse cover is fitted it must be of the correct colour as indicated by the colou red marking or the colour that is embossed in words on the base of the plug Replacements can be obtained directly from your nearest Service Depot Removing the plug If your appliance has a non rewireable moul ded plug and you should wish to re route the mains cable through partitions units etc please ensure that either the plug is replaced by a fused 13 ampere rewireable plug bearing the BSI mark of ap proval Or the mains cable is wired directly into a 13 amp cable outlet controlled by a switch in compliance with BS 5733 which is accessible without moving the appliance Disposing of the plug Ensure that before disposing of the plug itself you make the pins unusable so that it cannot be accidentally inserted into a socket Instructions for connecting cable to an alternati ve plug Important the wires in the mains lead are co loured in accordance with the following code Green amp Yellow Earth Blue Neutral Brown Live As the colours of the wires in the lead may not correspond with the coloured markings iden tifying the terminals in your plug proceed as follows Connect Green amp Yellow wire to terminal marked E or or coloured Green or Green amp Yellow Connect Br
5. into the washing machine make sure the drum is empty Disposal e Disposing of the packaging materials observe local regulations so that the packaging may be re used e The European Directive 2012 19 EU on Waste Electrical and Electronic Equipment requires that old household electrical appliances must not be disposed of in the normal unsorted municipal waste stream Old applian ces must be collected separately in order to optimise the recovery and recycling of the materials they contain and reduce the impact on human health and the envi ronment The crossed out wheeled bin symbol on the product reminds you of your obligation that when you dispose of the appliance it must be separately collected Consumers should contact their local authority or retailer for information concerning the correct disposal of their old appliance Opening the porthole door manually In the event that it is not possible to open the porthole door due to a powercut and if you wish to remove the laundry proceed as follows 1 remove the plug from the electrical socket 2 make sure the water level inside the machine is lower than the door opening if it is not remove excess water using the drain hose collec ting it in a bucket as indicated in the figure 3 using a screwdriver remo ve the cover panel on the lo wer front part of the washing machine see figure 4 pull outwards using the tab as indicated in the figure un
6. or hand and machine wash or the like Too much detergent was used less detergent is required in soft water To comply with new energy saving regulations the machine is fitted with an automatic standby system Press ON OFF button for 3 seconds to activate the machine it can then either be switched off or a new programme selected Your washing machine contains sensors that monitor progress during the wash cycle eg Water Levels Temperatures Out of Balance loads Wash time pro gress Normally if your machine successfully completes the cycle there is unlikely to be anything wrong Remember you will be charged for a service call for problems caused by incorrect installation as listed above Not emptying contents from pockets may cause pump or drain blockages or may damage the machine Do not wash items which do not have a wash label or wash items that are not intended as machine washable 14 Assistance E Hotpoint Guarantee cE 12 Months Parts and Labour Guarantee Your appliance has the benefit of our manufacturer s guarantee which covers the cost of breakdown repairs for twelve months from the date of purchase This gives you the reassurance that if within that time your appliance is proven to be defective because of either workmanship or materials we will at our discretion either repair or replace the appliance at no cost to you This guarantee is subject to the following conditions The app
7. E Serial number oo Parts and Accessories We supply a full range of genuine replacement parts as well as accessory products that protect and hygienically clean your appliance to keep it looking good and functioning efficiently throughout its life UK 08448 225 225 Republic of Ireland 0818 313 413 www hotpointservice co uk Appliance Registration We want to give you additional benefits of Hotpoint ownership To activate your free 5 year parts guarantee you must register your appliance with us UK 08448 24 24 24 Republic of Ireland 01 230 0800 www hotpointservice co uk Indesit Company UK Ltd Morley Way Peterborough PE2 9JB Indesit Company Unit 49 Airways Industrial Estate Dublin 17 amp Recycling amp Disposal Information As part of Hotpoint s continued commitment to helping the environment Hotpoint reserves the right to use quality recycled components to keep down customer costs and minimise material wastage Please dispose of packaging and old appliances carefully To minimise the risk of injury to children remove the door plug and cut the mains cable off flush with the appliance Dispose of these parts separately to ensure that the appliance can no longer be plugged into a mains socket and the door cannot be locked shut 16
8. Instructions for use English 1 WMYL 641 E Hotpoint STYLE WASHING MACHINE Contents Installation 2 3 4 5 Unpacking and levelling Connecting the electricity and water supplies The first wash cycle Technical data Care and maintenance 6 Cutting off the water or electricity supply Cleaning the washing machine Cleaning the detergent dispenser drawer Caring for the door and drum of your appliance Cleaning the pump Checking the water inlet hose Precautions and tips 7 General safety Disposal Opening the porthole door manually Description of the washing machine and starting a wash cycle 8 9 Control panel Indicator lights Starting a wash cycle Wash cycles 10 Table of wash cycles Personalisation 11 Setting the temperature Setting the spin speed Functions Detergents and laundry 12 Detergent dispenser drawer Preparing the laundry Garments requiring special care Load balancing system Troubleshooting 13 14 Assistance 15 16 Installation Keep this instruction manual in a safe place for future reference Should the appliance be sold transferred or moved make sure the instruction manual accompanies the washing machine to inform the new owner as to its operation and features Read these instructions carefully they contain vital information on installation use and safety Unpacking and levelling Unpacking This is a separate part of the polystyre ne base and should b
9. continue to try to repeat the distribution of the load required before the machine will go into higher spin speeds This will increase the programme time accordingly This is a safety feature to prevent damage Out of Balance can be caused by washing a single heavy item eg duvet quilt etc Try the programme again using a different load The dispenser drawer is blocked with detergent and requires cleaning The water pressure is too high and requires turning down turn down the tap on the water supply pipe slightly and try again The machine is tilting forwards It must be level when in its final position The fill hose is loose check both the cabinet and tap ends The fill hose is tight but still leaks if so replace the rubber washers or the fill hose is missing the rubber washer The drain hose is not fixed in properly Switch off the machine and unplug it wait for approximately 1 minute and then switch it back on again If the problem persists contact the Technical Assistance Service The machine requires a service wash Run n 2 wash cycle with detergent and no laundry The door will not open until the door lock indicator light goes out shortly after the program has finished The door seal has drainage holes at the bottom This is normal The water level is correct if it can be seen at the bottom of the door The detergent is not suitable for machine washing it should display the text for washing machines
10. dge of a basin or sink be sure the free end of the hose should not be under We advise against the use of hose extensions in case of absolute need the extension must have the same diameter as the original hose and must not exceed 150 cm in length Ensure that if the drain hose is pushed into a Standpipe that the end does not go down more than 15cms 6 inches If the hose is pu shed down too far this may cause the machine to self syphon ie continuously empty as it is filling Electric connection Before plugging the appliance into the mains socket make sure that e the socket is earthed and in compliance with the applicable law e the socket is able to sustain the appliance s maximum power load indicated on the Tech nical Data Plate fixed on the machine e the supply voltage is included within the values indicated on the Technical Data Plate fixed on the machine e the socket is compatible with the washing machine s plug If this is not the case repla ce the socket or the plug Your appliance is now supplied with a 13 amp fused plug it can be plugged into a 13 amp socket for immediate use Before using the appliance please read the instructions below WARNING THIS APPLIANCE MUST BE EARTHED THE FOLLOWING OPERATIONS SHOULD BE CARRIED OUT BY A QUALIFIED ELECTRI CIAN Replacing the fuse When replacing a faulty fuse a 13 amp ASTA approved fuse to BS 1362 should always be used and the fuse
11. e simply call our registration line on 08448 24 24 24 ROI 01 230 0800 Extended Guarantees We offer a selection of repair protection plans that enable you to fully cover yourself against the expense of repair bills for the life of your policy To find the ideal plan for you please call our advice line on 08448 226 226 Republic of Ireland 01 230 0233 Free Helpdesk Service We have a dedicated team who can provide free advice and assistance with your appliance if you experience any technical difficulties within the first 90 days of ownership Simply call our Hotpoint Service Hotline on 08448 224 224 Republic of Ireland 0818 313 413 for telephone assistance or where necessary to arrange for an engineer to call If we cannot resolve the technical problem we will replace your machine or if you prefer give you your money back 15 195114035 00 04 2013 Xerox Fabriano ce After Sales Service No one is better placed to care for your Hotpoint appliance during the course of its working life than us the manufacturer Essential Contact Information Hotpoint Service We are the largest service team in Europe offering you access to 400 skilled telephone advisors and 1000 fully qualified engineers on call to ensure you receive fast reliable local service UK 08448 224 224 Republic of Ireland 0818 313 413 www hotpointservice co uk Please note Our advisors will require the following information Model number
12. e removed with the base IMPORTANT check when unpacking your machine 1 Unpack the washing machine 2 Check whether the washing machine has been damaged during transport If this is the case do not install it and contact your retailer 3 Remove the 4 pro tective screws and the rubber bush with the respective spacer situated on the rear of the appliance see also the installation leaflet 4 Seal the gaps using the plastic plugs provi ded 5 Keep all the parts you will need them again if the washing machine needs to be moved to another location Packaging materials are not children s toys Levelling Your machine may make a considerable amount of noise if the two front feet have not been adjusted correctly 1 Install the washing machine on a flat stur dy floor without resting it up against walls ca binets or anything else 2 lf the floor is not perfectly level compensate for any unevenness by tightening or loosening the adjustable front feet see figure the an gle of inclination measured according to the worktop must not exceed 2 Levelling your appliance correctly will provide it with stability and avoid any vibrations noise and shifting during operation If it is placed on a fitted or loose carpet adjust the feet in such a way as to allow enough room for ventilation beneath the washing machine Electric and water connections Connecting t
13. ed or even set to a cold wash amp The washing machine will automatically prevent you from selecting a temperature which is higher than the maximum value set for each wash cycle Exception if the 3 programme is selected the temperature can be increased up to a value of 90 C Setting the spin speed Turn the SPIN SPEED knob to set the spin speed for the selected wash cycle The maximum spin speeds available for each wash cycle are as follows Wash cycles Maximum spin speed Cottons 1400 rpm Synthetics 800 rpm Wool 800 rom Silk drain only The spin speed may be lowered or the spin cycle can be excluded altogether by selecting the symbol RK The washing machine will automatically prevent you from selecting a spin speed which is higher than the maximum speed set for each wash cycle Functions The various wash functions available with this washing machine will help to achieve the desired results every time To activate the functions 1 Press the button corresponding to the desired function 2 the function is enabled when the corresponding indicator light is illuminated Note If the indicator light flashes rapidly this signals that this particular function may not be selected in conjunction with the selected wash cycle Super Wash This option offers a high performance wash due to the greater quantity of water used in the initial phase of the cycle and due to the increased wash cycle duration is particularly usefu
14. efully General safety e This appliance was designed for domestic use only e This appliance can be used by children aged from 8 years and above and persons with re duced physical sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved Chil dren shall not play with the appliance Clea ning and user maintenance shall not be made by children without supervision Do not touch the machine when barefoot or with wet or damp hands or feet e Do not pull on the power supply cable when unplugging the appliance from the electricity socket Hold the plug and pull e Do not open the detergent dispenser drawer while the machine is in operation e Do not touch the drained water as it may reach extreme ly high temperatures Never force the porthole door This could damage the safety lock mechanism designed to prevent accidental opening If the appliance breaks down do not under any circum stances access the internal mechanisms in an attempt to repair it yourself Always keep children well away from the appliance while it is operating The door can become quite hot during the wash cycle If the appliance has to be moved work in a group of two or three people and handle it with the utmost care Never try to do this alone because the appliance is very heavy Before loading laundry
15. fore you use it for the first time run a wash cycle with detergent and no laundry setting the n 2 programme E Hotpoint Technical data Model WMYL 641 width 59 5 cm Dimensions height 85 cm depth 54 cm Capacity from 1 to 6 kg Electrical please refer to the technical connections data plate fixed to the machine Water con nections Spin speed Test wash cycles in accordan ce with directives 1061 2010 and 1015 201 C x maximum pressure 1 MPa 10 bar minimum pressure 0 05 MPa 0 5 bar drum capacity 52 litres up to 1400 rotations per minute Programme 3 Cotton Standard 60 Programme 4 Cotton Standard 40 This appliance conforms to the following EC Directives 2004 108 EC Electroma gnetic Compatibility 2006 95 EC Low Voltage 2012 19 EU Care and maintenance Cutting off the water and electri city supplies e Turn off the water tap after every wash cycle This will limit wear on the hydraulic system inside the washing machine and help to prevent leaks e Unplug the washing machine when cleaning it and during all maintenance work Cleaning the washing machine The outer parts and rubber components of the appliance can be cleaned using a soft cloth soaked in lukewarm soapy water Do not use solvents or abrasives Cleaning the detergent dispenser drawer Remove the dispen ser by raising it and pulling it out see figure Wash it under running wate
16. he water inlet hose 1 Connect the supply pipe by screwing it to a cold water tap using a 3 4 gas threaded connection see figu re Before performing the connection allow the water to run freely un til it is perfectly clear 2 Connect the other end of the water inlet hose to the washing machine screwing it onto the applian ce s cold water inlet situated on the top right hand side on the rear of the appliance see figure 3 Make sure there are no kinks or bends in the hose The water pressure at the tap must be within the values indicated in the Technical details table on the page 5 If the water inlet hose is not long enough contact a specialist store or an authorised serviceman Ensure that the supply taps are allowing wa ter through Old taps may seize in the closed position and thus prevent water reaching the machine t Never use second hand or old inlet hoses use the products supplied with the machine E Hotpoint Connecting the drain hose Connect the drain hose without ben ding it to a draining duct or a wall drain situated between 65 and 100 cm from the floor The drain hose may be connected to an under sink trap Before connecting the drain hose from the machine ensure that any blanks or removable ends have been taken off the spigot Where it connects to the waste water pipe cut end off spigot or remove the blanking cap If it is placed over the e
17. l for the removal of stubborn stains This function may not be used in conjunction with wash cycles 2 7 10 11 13 14 Z Extra Rinse By selecting this function the efficiency of the rinse is increased and optimal detergent removal is guaranteed It is particularly useful for sensitive skin This function may not be used in conjunction with wash cycles 7 11 14 Z Easy Iron By selecting this function the wash and spin cycles will be modified in order to reduce the formation of creases At the end of the cycle the washing machine will perform slow rotations of the drum the EASY IRON and START PAUSE indicator lights will flash orange and the END phase will remain lit in a fixed manner To end the cycle press the START PAUSE button or the EASY IRON button This function may not be used in conjunction with wash cycles 1 2 7 11 13 vy Time Saver If you select this option the wash cycle duration will be reduced by up to 50 depending on the selected cycle thereby gua ranteeing simultaneous water and energy saving Use this cycle for lightly soiled garments This function may not be used in conjunction with wash cycles 1 2 7 8 10 12 13 14 vHy 2 11 Detergents and laundry Detergent dispenser drawer Successful washing results also depend on the correct dose of detergent adding too much detergent will not necessarily result in a more efficient wash and may in fact cause build up on the inside of yo
18. liance has been installed and operated correctly and in accordance with our operating and maintenance instructions The appliance is used only on the electricity or gas supply printed on the rating plate The appliance has been used for normal domestic purposes only The appliance has not been altered serviced maintained dismantled or otherwise interfered with by any person not authorised by us Any repair work must be undertaken by us or our appointed agent Any parts removed during repair work or any appliance that is replaced become our property The appliance is used in the United Kingdom or Republic of Ireland The guarantee does not cover Damage resulting from transportation improper use neglect or interference or as a result of improper installation Replacement of any consumable item or accessory These include but are not limited to plugs cables batteries light bulbs fluorescent tubes and starters covers and filters Replacement of any removable parts made of glass or plastic THIS GUARANTEE WILL NOT APPLY IF THE APPLIANCE HAS BEEN USED IN COMMERCIAL OR NON DOMESTIC PREMISES 5 Year Parts Guarantee Hotpoint also offers you a free 5 year parts guarantee This additional guarantee is conditional on you registering your appliance with us and the parts being fitted by one of our authorised engineers There will be a charge for our engineer s time To activate the extra parts warranty on your applianc
19. lights START PAUSE button with indicator light starts or tem porarily interrupts the wash cycles N B To pause the wash cycle in progress press this button the corresponding indicator light will flash orange while the indicator light for the current wash cycle phase will remain lit in a fixed manner If the DOOR LOCKED p indicator light is switched off the door may be opened To start the wash cycle from the point at which it was interrupted press this button again Standby mode This washing machine in compliance with new energy sa ving regulations is fitted with an automatic standby system which is enabled after about 30 minutes if no activity is detected Press the ON OFF button briefly and wait for the machine to start up again Consumption in off mode 0 5 W Consumption in Left on 8 W E Hotpoint Indicator lights The indicator lights provide important information This is what they can tell you Wash cycle phase indicator lights Once the desired wash cycle has been selected and has begun the indicator lights switch on one by one to indicate which phase of the cycle is currently in progress Wash p Rinse WM Ey Spin Pump out Uy End of wash cycle END Function buttons and corresponding indicator lights When a function is selected the corresponding indicator light will illuminate If the selected function is not compatible with the pro grammed wash cycle the corresponding indicator light will
20. meoe CC E E E E E A The length of cycle shown in this booklet is an estimation only and is calculated assuming standard working conditions The actual duration can vary according to factors such as water temperature and pressure the amount of detergent used the amount and type of load inserted load balancing and any wash options selected 1 Test wash cycle in compliance with directive 1061 2010 set wash cycle 3 with a temperature of 60 C This cycle is designed for cotton loads with a normal soil level and is the most efficient in terms of both electricity and water consumption it should be used for garments which can be washed at 60 C The actual washing temperature may differ from the indicated value 2 Test wash cycle in compliance with directive 1061 2010 set wash cycle 4 with a temperature of 40 C This cycle is designed for cotton loads with a normal soil level and is the most efficient in terms of both electricity and water consumption it should be used for garments which can be washed at 40 C The actual washing temperature may differ from the indicated value For all Test Institutes 2 Long wash cycle for cottons set wash cycle 4 with a temperature of 40 C 3 Long wash cycle for synthetics set wash cycle 6 with a temperature of 40 C 10 Personalisation Hotpoint Setting the temperature Turn the TEMPERATURE knob to set the wash temperature see Table of wash cycles The temperature may be lower
21. on and select a new cycle 9 At the end of the wash cycle the END indicator light will switch on The DOOR LOCKED indicator light will switch off indi cating that the door may be opened Take out your laundry and leave the appliance door ajar to make sure the drum dries completely Switch the washing machine off by pressing the ON OFF button Wash cycles Table of wash cycles Detergents Max Description of the wash cycle temp C Wash cycles Residual dampness Energy consumption kWh a Fabric softener elelee gt fala akici ya Cycle duration Cotton Standard 60 1 heavily soiled whites and resistant colours 1400 O BEGG Total water It a a aH i ro a lt Cotton Standard 40 2 a soiled resistant and delicate colours 1400 0 86 5 Cotton Standard 20 ighty soled resistant and dicate colours r a erica aeaa a amo fe a ae ons ar BS a CD AA SPECIALS eT Co cco ie ee 1000 145 9 Bed amp Bath washes bathroom laundry and bedlinen D 1400 125 Fastwash 60 to refresh normal soiled garments quickly not suitable for 10 wool silk and clothes which require washing by hand oo a 3 5 vo Fastwash 30 to refresh lightly soiled garments quickly not suitable for 800 71 0 15 35 Eg wool silk and clothes which require washing by hand EXTRAS a E EC 13 Woot for woo cashmere et eo fe eo fis aC Partials cycles Pasi ee ooo fefsome
22. own wire to terminal marked L or coloured Red Connect Blue wire to terminal marked N or coloured Black If a 13 amp plug BS 1363 is used it must be fitted with a 13 amp fuse either in the plug or adaptor or at the distribution board If you are in any doubt regarding the electrical supply to your machine consult a qualified electrician before use How to connect an alternative plug The wires in this mains lead are coloured in accordance with the following code BLUE NEUTRAL N BROWN LIVE L GREEN amp YELLOW EARTH E GREEN amp YELLOW M F CROSS BAR srown_ KOL fil GRIP Disposing of the appliance When disposing of the appliance please re move the plug by cutting the mains cable as close as possible to the plug body and dispo se of it as described on the previous page The washing machine should not be installed in an outdoor environment not even where the area is sheltered because it may be very dangerous to leave it exposed to damp rain and thunderstorms When the washing machine is installed the mains socket must be within easy reach Do not use extensions or multiple sockets The power supply cable must never be bent or dangerously compressed The power supply cable must only be repla ced by an authorised serviceman Warning The company denies all liability if and when these norms are not respected The first wash cycle Once the appliance has been installed and be
23. r this operation should be repeated frequently Caring for the door and drum of your appliance e Always leave the porthole door ajar in order to prevent unpleasant odours from forming Cleaning the pump The washing machine is fitted with a self clea ning pump which does not require any mainte nance Sometimes small items Such as coins or buttons may fall into the pre chamber which protects the pump situated in its bottom part Make sure the wash cycle has finished and unplug the appliance To access the pre chamber 1 using a screwdri ver remove the cover panel on the lower front part of the wa shing machine see figure o 2 unscrew the lid by rotating it anti clockwise See figu re a little water may trickle out This is perfectly normal 3 clean the inside thoroughly 4 screw the lid back on 5 reposition the panel making sure the hooks are securely in place before you push it onto the appliance Checking the water inlet hose Check the inlet hose at least once a year If there are any cracks it should be replaced immediately during the wash cycles water pressure is very strong and a cracked hose could easily split open t Never use second hand hoses Precautions and tips This washing machine was designed and constructed in accordance with international safety regulations The fol lowing information is provided for safety reasons and must therefore be read car
24. ress the START PAUSE button e The Spin Speed selector knob is in the OR position e The Temperature selector knob is in the s amp position Programme times will vary due to water pressure the incoming water tempe rature and if the wash load goes out of balance This will increase the pro gramme times accordingly See The machine wont spin properly below e The feet have not been adjusted enabling the machine to rock New Installation Either the Transit Bolts including the plastic spacers or the Polystyrene Packaging have not been removed when installing the machine e The machine is trapped between cabinets and or walls e The load is in a slight out of balance condition and machine is spinning but at a lower speed 13 The machine is noisy The machine wont spin properly The machine leaks from the dispenser The machine leaks other than dispenser The indicator lights on the console are flashing rapidly The machine smells The machine door cannot be opened Door Seal damaged at the bottom The water level is too low when the machine is washing There is too much foam After completing the programme or before starting a programme the machine has turned itself off no lights General There will always be some motor pump and drum noise during spin Out of Balance detected when attempting to go into a spin cycle If this happens the machine will
25. ry spin cycle to avoid excessive vibrations before every spin and to distribute the load in a uniform manner the drum rotates continuously at a speed which is slightly greater than the washing rotation speed If after several attempts the load is not balanced correctly the machine spins at a reduced spin speed If the load is excessively unbalanced the washing machine performs the distribution process instead of spinning To encourage improved load distribution and balance we recommend small and large garments are mixed in the load n Troubleshooting Hotpoint Your washing machine could fail to work Before contacting the Technical Assistance Centre see Assistance make sure that the problem cannot be solved easily using the following list Problem The machine does not switch on The wash cycle does not start The machine does not fill with wa ter or the indicator light for the first wash cycle stage flashes rapidly The machine continuously fills with water and continually drains away or Water left in the drum or Stuck on wash The machine does not drain or spin The machine does not heat or poor wash results The programme takes too long The machine vibrates a lot during the spin cycle Possible causes Solutions e The appliance is not plugged into the socket fully or not enough to make contact e There is no power to the socket or the fuse has blown in the mains plug e The door i
26. s not closed properly e The ON OFF button has not been pressed e The START PAUSE button has not been pressed e The water tap has not been turned on to allow water to flow into the machine ter inlet hose is kinked er inlet hose is not connected to the water supply e The water pressure is too low e The water tap has not been turned on to allow water to flow into the machine e There is no water supply to the house e The inlet valve filter is blocked e The START PAUSE button has not been pressed e The wa e The wa e The top of the drain hose is too low It must be fitted at a height between 65 and 100 cm from the floor see Installation e The drain hose is connected incorrectly to the sink trap allowing water to run into the machine the drain hose must be positioned higher than the bottom of the sink to prevent water flowing down the drain hose e The end of the drain hose has been pushed too far down the standpipe the U bracket should be fitted 100 mm from the end of the drain hose e The Pump filter is blocked e The drain hose is kinked see nstallation e New Installation The blanking cap or spigot has not been removed if con nected under a sink e The drain hose or sink trap is blocked e The wash cycle does not include draining some wash cycles require the drain phase to be started manually e The EASY IRON function button has been activated To complete the wash cycle p
27. til the plastic tie rod is freed from its stop position pull downwards and open the door at the same time 5 reposition the panel making sure the hooks are securely in place before you push it onto the appliance E Hotpoint Description of the washing machine and starting a wash cycle cB Control panel waAsHeveLE PROGRESS indicator lights SPIN SPEED knob ON OFF button pean TEMPERATURE abet knob indicator light Detergent dispenser drawer WASH CYCLE knob Detergent dispenser drawer used to dispense detergents and washing additives see Detergents and laundry ON OFF button switches the washing machine on and off WASH CYCLE knob programmes the wash cycles Du ring the wash cycle the knob does not move FUNCTION buttons with indicator light used to select the available functions The indicator light corresponding to the selected function will remain lit TEMPERATURE knob sets the temperature or the cold wash cycle see Personalisation SPIN SPEED knob sets the spin speed or exclude the spin cycle completely see Personalisation WASH CYCLE PROGRESS indicator lights used to monitor the progress of the wash cycle The illuminated indicator light shows which phase is in progress DOOR LOCKED indicator light indicates whether the door may be opened or not see next page START PAUSE button with indicator FUNCTION light buttons with indicator
28. ur appliance and contri bute to environmental pollution Use powder detergent for white cotton garments for pre washing and for washing at temperatures over 60 C Follow the instructions given on the detergent packaging Do not use hand washing detergents they create too much foam Open the detergent dispenser drawer and pour in the deter gent or washing additive as follows Do not pour detergent into the middle compartment Deter gent should only be poured into the compartment 1 compartment 1 Detergent for the wash cycle powder or liquid If liquid detergent is used it is recommended that the removable plastic partition A Supplied be used for proper dosage If powder detergent is used place the partition into slot B compartment 2 Additives fabric softeners etc The fabric softener should not overflow the grid Preparing the laundry e Divide the laundry according to the type of fabric the symbol on the label the colours separate coloured garments from whites e Empty all garment pockets and check the buttons e Do not exceed the listed values which refer to the weight of the laundry when dry see Table of program mes and wash cycles How much does your laundry weigh 1 sheet 400 500 g 1 pillow case 150 200 g 1 tablecloth 400 500 g 1 bathrobe 900 1 200 g 1 towel 150 250 g Garments requiring special care Anti Stain the programme 1 is suitable to heavily soiled
Download Pdf Manuals
Related Search