Premier Mounts PBM-070L project mount
Contents
1. 5 PROJECTOR ADJUSTMENT 7 TECHNICAL SPECIFICATIONS 8 WARRANTY 9 Warning Statements THE CEILING STRUCTURE MUST BE CAPABLE OF SUPPORTING AT LEAST FIVE 5 TIMES THE WEIGHT OF THE PROJECTOR IF NOT THE CEILING MUST BE REINFORCED PROPER INSTALLATION PROCEDURE BY A QUALIFIED SERVICE TECHNICIAN AS OUTLINED IN THE INSTALLATION INSTRUCTIONS MUST BE ADHERED TO FAILURE TO DO SO COULD RESULT IN SERIOUS PERSONAL INJURY OR EVEN DEATH THE MAXIMUM WEIGHT THAT CAN BE USED WITH THIS PROJECTOR IS 200LBS SAFETY MEASURES MUST BE PRACTICED AT ALL TIMES DURING THE INSTALLATION OF THIS PRODUCT USE PROPER SAFETY GEAR AND TOOLS FOR THE INSTALLATION PROCEDURE TO PREVENT PERSONAL INJURY PRIOR TO THE INSTALLATION OF THIS PRODUCT THE INSTALLATION INSTRUCTIONS SHOULD BE READ AND COMPLETELY UNDERSTOOD THE INSTALLATION INSTRUCTIONS MUST BE READ TO PREVENT PERSONAL INJURY AND PROPERTY DAMAGE KEEP THESE INSTALLATION IN2. 5 Once all adjustments have been made tighten all hardware AST 2446 AST 1321 or 12 Pipe M6 Set Screw Tilt Locking Screws Hinge Pin Screw Flat Washer Nylon Spacer Roll Adjustment Screws PBM 070L Page 8 Installation Manual Technical Specifications All measurements are inches mm All base boxes feature the following adjustments to facilitate ease of installation A Tilt of 6 from center B Roll of 3 from center C Yaw of 360 when used with 1 or 1 mount threaded pipe D Direct mating with standard 1 and 1 mount threaded pipe PBM 070L Installation Manual Page 9 Warranty PREMIER MOUNTS LIMITED LIFETIME WARRANTY What and Who is Covered by this Limited Warranty and for How Long Premier Mounts warrants this product to be free from defects in material and workmanship for the lifetime of the original installation of this product The limited warranty is valid only for the original purchaser of the product What Premier Mounts Will Do At the sole option of Premier Mounts Premier Mounts will repair or replace any product or product part that is defective If Premier Mounts chooses to replace a defective product or part a replacement product or part will be shipped to you at no charge but you must pay any labor costs What is Not Covered Limitations PREMIER MOUNTS DISCLAIMS ANY LIABILITY FOR DAMAGE TO MOUNTS ADAPTERS DISPLAYS PROJECTORS OTHER PROPERTY OR PERSONAL INJURY RESULTI
3. INSTALLATION INSTRUCTIONS PBM 070L NORTH AMERICA EUROPE AUSTRALIA NEW ZEALAND OCEANIA DISTRIBUTOR 3130 East Miraloma Avenue Anaheim CA 92806 USA USA and Canada Phone 800 368 9700 Fax 800 832 4888 Swallow House Shilton Industrial Estate Shilton Coventry England CV79JY Phone 44 0 2476 614700 Fax 44 0 2476 614710 P O Box 295 Mordialloc Victoria 3195 Australia Phone 039586 6330 www premiermounts com au Other Locations Phone 001 714 632 7100 Fax 001 714 632 1044 Premier Mounts 2008 9530 007 003 00 PBM 070L Installation Manual Page 2 Table of Contents WARNING STATEMENTS 2 PARTS LIST 3 INSTALLATION TOOLS 3 PROJECTOR BRACKET INSTALLATION 4 CEILING INSTALLATION
4. Install the jam screw all the way up to the end of the threads of the threaded PBM 070L Step 11 Screw in the 1 bridge opening to the PBM 070L all the way up to the jam screw Step 12 Tighten the jam screw and the base box together Step 13 Loosely install the hinge pin screws flat washer and conical spacer to each side of the base box Step 14 Slide the conical spacer and the flat washer to the back of the screws Step 15 Raise the projector mount attached to the projector s chassis and insert the hinge pins through the hinge pin openings Step 16 Raise the rear of the projector and install the four 4 M6 x 12 mm tilt locking screws to the rear of the base box adjust the tilt and lock it Step 17 Tighten the two 2 M6 x 12 mm hinge pin screws Step 18 At this time use the M3 Allen wrench to tighten the M6 x 6mm set screw Projector Adjustment Step 1 You can adjust the roll of the projector by loosening the three 3 front and rear M6 x 12mm screws Do not over tighten the screws Step 2 Set the desired roll and then tighten the screws First tighten the center screws and work your way to the outside screws making any final adjustments prior to tightening the last two screws Step 3 You can adjust the tilt of the projector by loosening the four 4 M6 x 12mm screws two on each side of the base box Step 4 Set the desired tilt and then tighten the screws making any final adjustments prior to tightening the last two screws Step
5. NG IN WHOLE OR IN PART FROM IMPROPER INSTALLATION MODIFICATION USE OR MISUSE OF ITS PRODUCTS PREMIER MOUNTS DISCLAIMS ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE PREMIER MOUNTS IS NOT RESPONSIBLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES INCLUDING BUT NOT LIMITED TO INABILITY TO USE ITS PRODUCTS OR LABOR COSTS FOR REMOVING AND REPLACING DEFECTIVE PRODUCTS OR PARTS SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU What Customers Must Do for Limited Warranty Service If you discover a problem that you think may be covered by the warranty you MUST REPORT it in writing to the address below within thirty 30 days Proof of purchase an original sales receipt from the original consumer purchaser must accompany all warranty claims Warranty claims must also include a description of the problem the purchaser s name address and telephone number General inquiries can be addressed to Premier Mounts Customer Service at 1 800 368 9700 Warranty claims will not be accepted over the phone or by fax Premier Mounts Attn Warranty Claim 3130 E Miraloma Avenue Anaheim CA 92806 How State Law Applies THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE
6. STRUCTIONS IN AN EASILY ACCESSIBLE LOCATION FOR FUTURE REFERENCE Indicates that the power plug is to be disconnected from the power outlet Contact Premier Mounts with any questions 800 368 9700 Safety precautions must be taken at all times Warning and Caution statements A secure structure must support the weight or load of the projector When mounting to a ceiling that contains wooden studs dead center of the wooden stud must be confirmed prior to installation Do not install on a structure that is prone to vibration movement or chance of impact Failure to do so could result in damage to the projector and or damage to the mounting surface Do not install near heater fireplace direct sunlight air conditioning or any other source of direct heat energy Failure to do so may result in damage to the projector and could increase the risk of fire At least two qualified people should perform the installation procedure Injury and or damage can result from dropping or mishandling the projector Recommended mounting surfaces wooden studs and solid flat concrete If the mount is to be installed on any surface other than wooden studs use suitable hardware which is commercially available PBM 070L Installation Manual Page 3 Parts List This mount is shipped with all proper installation hardware and components Make sure that none of these parts are missing and or damaged before beginning installation If
7. six 6 M6 x 12 mm screws that are located on the base box three on each side A Step 2 Secure the top bridge to the ceiling structure at this time see warning label using commercially available hardware B Step 3 Use the two 2 middle slot openings for single wood stud mounting All other mounting points on the top bridge may be used depending on your installation application B Step 4 Replace the base box to the secured top bridge and secure with the six M6 x 12 mm screws C Base Box Lag Bolts Commercially Available Ceiling Structure Wood Stud Top Bridge A B C PBM 070L Page 6 Installation Manual Step 5 Loosely install the hinge pin screws flat washer and nylon spacer to each side of the base box Step 6 Slide the nylon spacer and the flat washer to the back of the screws Step 7 Raise the mounting bracket and attached projector to the base box and insert the hinge pins through the hinge pin openings Step 8 Tighten the hinge pin screws Step 9 Determine the viewing angle Once the viewing angle has been determined insert and tighten the four 4 tilt locking screws Do not over tighten the screws Ceiling Structure Top Bridge Hinge Pin Bolt Flat Washer Tilt Locking Screws Wood Stud PBM 070L Page 7 Installation Manual If installing a PBM 070L from the ceiling structure please refer to the installation instructions that are included with those mounts Step 10
8. there are parts missing and or damaged please stop the installation and contact Premier Mounts 800 368 9700 Base Box Qty 1 Projector Bracket Qty 1 Jam Nut Qty 1 M6 x 6mm Set Screw Qty 1 Nylon Spacers Qty 2 Flat Washers Qty 2 M6 x 12mm Phillips Head Screws Qty 6 Projector Bracket Hardware M8 x 12mm Phillips Head Screws Qty 8 Installation Tools Soft Material Blanket Portable Drill M3 Allen Wrench Supplied Pencil Finder Commercially Available Level Tape Measure Phillips Head Screw Driver Ladder PBM 070L Installation Manual Page 4 Projector Bracket Installation M8 x12mm Phillips Head Screws Projector Bracket Projector Screwdriver M8 x12mm Phillips Head Screws Step 1 Invert the projector and place it on a soft and flat surface Remove any foot levelers that might possibly prevent the correct installation of the bracket Step 2 Locate the eight mounting points located on the bottom of the projector Step 3 Line up the mounting points on the projector with the mounting holes on the mounting bracket Step 1 Using a screwdriver secure the mounting bracket using eight 8 M8 x 12mm Phillips Head screws Do not over tighten these screws Over tightening the screws may result in damaging the threaded inserts on the projector PBM 070L Installation Manual Page 5 Ceiling Installation Step 1 Separate the top bridge from the base box by removing the
Download Pdf Manuals
Related Search