Premier Mounts AM225T flat panel wall mount
Contents
1. Identify the general location on the wall where you will be mounting your flat panel Use a stud finder to determine the exact center of each steel stud in the vicinity of the mounting location Ne ye b Use a pencil and mark the exact center of each steel stud L Pres ka Installation Instructions Visit the Premier Mounts website at http www premiermounts com Page 9 b 4 24 P4263T Installing the Wall Plate cont d Place the wall plate against the wall in the desired viewing location Adjust the wall plate to match the locations of the steel studs Level the wall plate Use a pencil and mark 2 upper and 2 lower locations where you will be drilling holes for the steel stud anchors Set the wall plate to one side in a safe location Use a power drill and 7 4 drill bit to drill a hole at each of the marks Insert a steel stud anchor into each hole If necessary lightly tap each steel stud anchor into place with a hammer Use a Phillips screwdriver to tighten each steel stud anchor screw until the legs have completely compressed against the back of the steel stud uns Il The steel stud anchor screw will feel tight when w you first begin to turn it until the legs begin to compress The steel stud anchor screw will then turn easier for several turns The steel stud anchor screw will again feel tight when the legs have completely compressed agai2. Warning Statements PRIOR TO THE INSTALLATION OF THIS PRODUCT THE INSTALLATION INSTRUCTIONS MUST BE READ AND COMPLETELY UNDERSTOOD KEEP THESE INSTALLATION INSTRUCTIONS IN AN EASILY ACCESSIBLE LOCATION FOR FUTURE REFERENCE PROPER INSTALLATION PROCEDURE BY A QUALIFIED SERVICE TECHNICIAN MUST BE FOLLOWED AS OUTLINED STOP IN THESE INSTALLATION INSTRUCTIONS FAILURE TO DO SO COULD RESULT IN PROPERTY DAMAGE SERIOUS PERSONAL INJURY OR EVEN DEATH SAFETY MEASURES MUST BE PRACTICED AT ALL TIMES DURING THE ASSEMBLY OF THIS PRODUCT USE STOP PROPER SAFETY EQUIPMENT AND TOOLS FOR THE ASSEMBLY PROCEDURE TO PREVENT PERSONAL INJURY PREMIER MOUNTS DOES NOT WARRANT AGAINST DAMAGE CAUSED BY THE USE OF ANY PREMIER MOUNTS PRODUCT FOR PURPOSES OTHER THAN THOSE FOR WHICH IT WAS DESIGNED OR DAMAGE CAUSED BY UNAUTHORIZED ATTACHMENTS OR MODIFICATIONS AND IS NOT RESPONSIBLE FOR ANY DAMAGES CLAIMS DEMANDS SUITS ACTIONS OR CAUSES OF ACTION OF WHATEVER KIND RESULTING FROM ARISING OUT OF OR INANY MANNER RELATING TO ANY SUCH USE ATTACHMENTS OR MODIFICATIONS At least two qualified people should perform the assembly procedure Personal injury and or property damage can result from dropping or mishandling the flat panel If mounting to wall studs or ceiling studs make sure that the mounting screws are anchored into the center of the wall studs or ceiling studs Use of an edge to edge stud finder is recommended A It is recommended that a maximum of plast
3. proceed to the Concrete Installation section If you will be installing your P4263T mount to a steel frame proceed to the Steel Stud Installation section Wood Stud Installation You must secure the wall plate to two 2 wall studs with a minimum of four 4 lag bolts 2 lag bolts for each stud found Use a stud finder to determine the exact center of wall studs in the vicinity of the wall plate Use a pencil to mark the exact center of each of the wall studs Two people are recommended for this step one person to level the wall plate and another person to mark the wall stud location Place the wall plate against the wall in the desired viewing location Adjust the wall plate to align the mount slots in the wall plate with the center of the wall studs Level the wall plate Use a pencil to mark the upper right mounting location along the center of the wall stud Page 6 Visit the Premier Mounts website at http www premiermounts com Installation Instructions gt 4 P4263T 24 Installing the Wall Plate contd Drill a pilot hole in the center of the upper right mark using a 4 drill bit and power drill A Only use a 4 drill bit when drilling the pilot holes Place the wall plate against the wall and align it with the pilot hole Insert one 1 5 4 x 3 lag bolt and one 1 5h washer into the upper right mounting hole and tighten using a socket wrench and 7 socket A D
4. Mounts product has the following hardware and components before beginning installation If there are parts missing and or damaged stop the installation and call Premier Mounts at 800 368 9700 P4263T Universal Low Profile Tilt Mount Assembly Components lpccecceececececcceecee leccceccecceeeccoeecee y Mounting Brackets Wall Plate Qty 2 Qty 1 546 Flat Washers Universal Spacers Security Barrel Universal Washers Qty 1 Qty 6 Pro Mounting Hardware M6 Steel Stud Anchors 546 Concrete Wedge Anchors She x 3 Lag Bolts Qty 6 Qty 6 Qty 6 Installation Instructions Visit the Premier Mounts website at http www premiermounts com Page 3 b a 24 P4263T Parts List cont d Page 4 M4 x 16mm Screw Qty 6 M4 x 25mm Screw Qty 6 M4 x 30mm Screw Qty 6 M5 x 16mm Screw Qty 6 M5 x 25mm Screw Qty 6 M5 x 30mm Screw Qty 6 M6 x 16mm Screw Qty 6 M6 x 25mm Screw Qty 6 M6 x 30mm Screw Qty 6 M6 x 45mm Screw Qty 6 Mounting Hardware M8 x 16mm Screw Qty 6 M8 x 25mm Screw Qty 6 M8 x 30mm Screw Qty 6 M8 x 45mm Screw Qty 6 M8 x 70mm Screw Qty 4 Visit the Premier Mounts website at http www premiermounts com Installation Instructions P4263T 24 Leveling Screws Allows for leveling adjustments of the flat panel after moun
5. REMIER MOUNTS IS NOT RESPONSIBLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES INCLUDING BUT NOT LIMITED TO INABILITY TO USE ITS PRODUCTS OR LABOR COSTS FOR REMOVING AND REPLACING DEFECTIVE PRODUCTS OR PARTS SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU What Customers Must Do for Limited Warranty Service If you discover a problem that you think may be covered by the warranty you MUST REPORT it in writing to the address below within thirty 30 days Proof of purchase an original sales receipt from the original consumer purchaser must accompany all warranty claims Warranty claims must also include a description of the problem the purchaser s name address and telephone number General inquiries can be addressed to Premier Mounts Customer Service at 1 800 368 9700 Warranty claims will not be accepted over the phone or by fax Premier Mounts Attn Warranty Claim 3130 East Miraloma Ave Anaheim CA 92806 How State Law Applies THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE Premier Mounts intends to make this manual accurate and complete However Premier Mounts makes no claim that the information contained herein covers all details conditions or variations nor does it provide for every possible contingency in connection with the installation or use of this product The info
6. ches millimeters 0000000 000 000000 000000000 00000000000 JE Page 16 Visit the Premier Mounts website at http www premiermounts com Installation Instructions gt 4 P4263T PREMIER MOUNTS LIMITED LIFETIME WARRANTY What and Who is Covered by this Limited Warranty and for How Long Premier Mounts warrants this product to be free from defects in material and workmanship for the lifetime of the original owner of this product The limited warranty is valid only for the original purchaser of the product What Premier Mounts Will Do At the sole option of Premier Mounts Premier Mounts will repair or replace any product or product part that is defective If Premier Mounts chooses to replace a defective product or part a replacement product or part will be shipped to you at no charge but you must pay any labor costs What is Not Covered Limitations PREMIER MOUNTS DISCLAIMS ANY LIABILITY FOR DAMAGE TO MOUNTS ADAPTERS DISPLAYS PROJECTORS OTHER PROPERTY OR PERSONAL INJURY RESULTING IN WHOLE OR IN PART FROM IMPROPER INSTALLATION MODIFICATION USE OR MISUSE OF ITS PRODUCTS PREMIER MOUNTS DISCLAIMS ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FORA PARTICULAR PURPOSE P
7. e mounting hardware Proceed to the Attaching the Flat Panel to the Wall Plate section Lock It Security Barrel Installation Optional fy Optional security configurations include PCB CSL1 sold separaiciy Padlock Combination or Keyed commercially available Mounting Tab Please read the following directions to install the security barrel Remove the locking screw from the mounting bracket Place the locking screw into and through the security barrel See illustration below Re insert the locking screw and security barrel into the mounting bracket Tighten the locking screw and security barrel until seated in the mounting tab Do not thread the locking screw any further once it is even with the mounting tab see illustration to the right Threading the locking screw any further will prevent you from safely attaching the flat panel to the wall plate Do not overtighten the locking screw Proceed to the Attaching the Mounting Bracket to the Flat Panel section mm p Locking Screw Lock It Security Barrel N QQ mm Installation Instructions Visit the Premier Mounts website at http www premiermounts com Page 13 b 4 24 P4263T Attaching the Flat Panel to the Wall Plate A This section requires two people Do not release or flat panel until yo
8. er board be used when mounting to wooden studs Be aware of the mounting environment If drilling and or cutting into the mounting surface always make sure that there are no electrical wires in wall Cutting or drilling into an electrical line may cause serious personal injury Make sure there are no water or natural gas lines inside the wall where the mount is to be located Cutting or drilling into a water or gas line may cause severe property damage or personal injury This product is intended for indoor use only Use of this product outdoors could lead to product failure and or serious personal injury Do not install near sources of high heat Do not install on a structure that is prone to vibration movement or chance of impact Contact Premier Mounts with any questions 800 368 9700 techsupport mounts com Page 2 Visit the Premier Mounts website at http www premiermounts com Installation Instructions gt 4 P4263T 22 Installation Tools The following tools may be required depending upon your particular installation They are not included FE nn v4 Drill Bit for 7 16 Drill Bit for Electronic Stud Finder Wood Stud Steel Stud 546 Concrete Drill Bit Hand Held Drill Tape Measure Hammer Protective Eyewear Socket Wrench 2 Socket M10 Socket Phillips Tip Screwdriver Optional tools for steel stud installations Optional tools for concrete installations Parts List Make sure your Premier
9. n the Thread Depth Indicator as shown in Figure 2 and Figure 3 do not use this screw The screw length must not bypass the mark Marking the Depth Test each size of the screws provided Eee The correct screws should thread easily into the Thread Depth Indicator mount point and not pull out when tension is applied D Screw a he Small Straw or Toothpick Proceed to the Universal Washer Installation section Small Straw or Toothpick Installation Instructions Visit the Premier Mounts website at http www premiermounts com Page 11 b a eZ P4263T Installing the Mounting Bracket cont d Universal Washer Installation Premier Mounts Universal Washers are designed to accommodate the various M4 M5 M6 and M8 hole sizes required by flat panels Do not place excessive pressure on the back of the flat panel as this may damage your flat panel The Universal Washer must be installed between the head of the mounting screw and the mounting bracket as shown Does your flat panel have Recessed mount points Uneven mount points A curved back Any obstruction near the mount point If Yes you must install Universal Spacers Remove the mounting brackets Universal Washers and mounting 7 Mounting Screw screws from the back of the flat panel Proceed to the Universal Spacer Installation section Universal Washer If No skip to the Attaching the Mou
10. nst the back of the drywall Stop turning the steel stud anchor screw at that point A Do not overtighten the steel stud anchor screw Remove the steel stud anchor screws and set them aside Aa Steel stud anchors may come with small paper M washers You may leave them on the screw or discard them These small paper washers do not replace standard washers Page 10 Visit the Premier Mounts website at http www premiermounts com Installation Instructions Align the wall plate over the steel stud anchor sleeves Insert a steel stud anchor screw and a 4s washer into each steel stud anchor sleeve Use a Phillips screwdriver and tighten each steel stud anchor screw until it is just snug A Do not overtighten the steel stud anchor screws Do not use a power drill to tighten the steel stud anchor screws Proceed to the Installing the Mounting Bracket section Installing the Mounting Bracket Selecting the Mounting Hardware Insert the Thread Depth Indicator into the thread gt LA inserts found on the bottom or top of the flat panel Use a pencil to mark the depth of the thread insert on the Thread Depth Indicator as shown in Figure va 1 Insert the Thread Depth Indicator into the remaining thread inserts to compare and verify their depth Locate the correct diameter screw for the thread insert o a If the screw you selected is longer than the mark Z o
11. nting Bracket to the Flat Panel section Mounting Bracket Universal Spacer Installation Premier Mounts Universal Spacers allow you to attach the mounting bracket to flat panels which have recessed or uneven mount points Each Universal Spacer adds to the distance between the mounting bracket and your flat panel Flat Panel The Universal Spacers must be stacked and oriented as shown The Universal Spacers must only be installed between the mounting bracket and your flat panel The Universal Spacers will fit M4 M5 M6 and M8 screw sizes Proceed to the Attaching the Mounting Bracket to the Flat Panel section Page 12 Visit the Premier Mounts website at http www premiermounts com Installation Instructions P4263T 24 Installing the Mounting Bracket cont d Attaching the Mounting Bracket to the Flat Panel This section presumes that you have read and understood these sections Selecting the Proper Mounting Hardware Universal Washer Installation Universal Spacer Installation Place your flat panel screen side down on a soft flat surface Identify the number and location of the thread inserts on the back of your flat panel Aligning the holes on each mounting bracket with the thread inserts on the back of your flat panel Secure each mounting bracket to your flat panel by inserting a minimum of two 2 screws per bracket A Do not overtighten th
12. o not overtighten the lag bolt Level the wall plate Use a pencil to mark the remaining three 3 mounting locations along the center of each wall stud Two people are recommended for this step one person to level the wall plate and another person to drill the pilot holes Drill a pilot hole in the center of each of the marks with a power drill and a 1 4 drill bit A Only use 4 drill bit when drilling the pilot holes Installation Instructions Visit the Premier Mounts website at http www premiermounts com Page 7 b 4 eZ P4263T Installing the Wall Plate cont d Insert one 1 x x 3 lag bolt and one 1 h washer into each pilot hole Tighten all lag bolts using a socket wrench and 14 socket Do not overtighten the lag bolts when attaching the mount to the wall Improper installation may result in personal injury or property damage Proceed to the Installing the Mounting Bracket section Concrete Installation The supplied 5 6 concrete wedge anchors must be used for concrete installation You will need a concrete drill bit which is available at your closest hardware store Concrete Wedge Anchors a Example of 6 Concrete Drill Bit Not Included Two people are recommended for this step one person to level the wall plate and another person to mark the mounting locations Place the wall plate against the wall in the desired viewing loca
13. oe PREMIER Cad MOUNTS CREATING POSITIVE CUSTOMER EXPERIENCES INSTALLATION INSTRUCTIONS V i A j ES IR Q Q P4263T Universal Low Profile Tilt Mount for 42 to 63 Flat Panels NORTH AMERICA EUROPE 3130 East Miraloma Avenue Swallow House Anaheim CA 92806 USA Shilton Industrial Estate USA and Canada Shilton Coventry England CV79JY Phone 1 800 368 9700 Phone 44 0 2476 614700 Fax 1 800 832 4888 Fax 44 0 2476 614710 Other Locations Phone 001 714 632 7100 Fax 001 714 632 1044 Dus 9531 207 D01 04 LISTED gt 4 24 P4263T Weight Limitsissssns e ae AE Raman AEE A aaa ae eee 2 Warning Sue LENS CRE E E eae A 2 Installation TOOlS siriarren nananana const va nenna ANEAN ENA EEEa EAEE ea aden sat EHANA aE soaneya deeeavedenesuehwansteybahdhtnnestee cayeberndaeteess 3 RE RER EP en EE Re Re E decease eee DEN Aa RE UE aE 3 Mounting me LC UNE LE PR Re RO Siasiaeses sags eats cee 4 FGA GS occu eye tees RM ren Sac can tive daca aap etats cucu calves cate ENE Cash hn edt eis toss toi as ended evan oS een E EE 5 linstalling TERNEL 6 VATFOCU CH OM Re 6 Determining the Mounting Surface csecss se cdeccs chescaea acca AEAT AEA OREA E EAEE EEEE NEE E OREN 6 Wood Stud Installati n sisis siseses ei areh ea EE e aa oa a rE nes ram Eei Eaa i aa a ea Eai tm aE ri 6 Goncrete Installation sssscsss
14. one hand at the center top edge of the flat panel Place the other hand on the center bottom edge of the flat panel Using the upper hand gently pull the top of the flat panel towards you while the lower hand gently pushes the bottom of the flat panel away from you Adjusting the Flat Panel to the Original Position Place one hand at the center top edge of the flat panel Place the other hand on the center bottom edge of the flat panel Using the upper hand gently push the top of the flat panel towards the wall while the lower hand gently pulls the bottom of the flat panel away from the wall Utilizing the Security Barrel Your P4263T Mount includes one 1 Security Barrel which can provide additional theft deterrence for your flat panel PCB CSL1 Security Cable Thread the cable through the hole on the security barrel Attach the PCB CSL1 locking mechansim and secure it using the supplied key Padlock Place the locking hook through the hole of the security barrel Snap lock and locking hook together PCB CSL1 Padlock Combination or Keyed Installation Instructions Visit the Premier Mounts website at http www premiermounts com Page 15 24 P4263T Technical Specifications All measurements are in in
15. rmation contained in this document is subject to change without notice or obligation of any kind Premier Mounts makes no representation of warranty expressed or implied regarding the information contained herein Premier Mounts assumes no responsibility for accuracy completeness or sufficiency of the information contained in this document Premier Mounts 2010 Installation Instructions Visit the Premier Mounts website at http www premiermounts com Page 17
16. sssiunense use caves scvaveehessateevan chews speaeeavit Eaa Ra AEEA op bas crevecatet OS EE EFECTE EPG EREET E ETRE 8 Steel Stuid InStallatonines ES SR a a a Ses E r a a E E ES a EET 9 Installing the Mounting Bracket resse Mn soy ea E aE e S E ESO E E a e A EEan 11 Selecting the Mounting Hardware 2 11 Universal Washer Installation 12 Universal Spacer Installations veaatoasegsanevsetceeen oe achicg oct aacivatardencveanuSuanes AANE AA EE tad enen dense Sete r eee man EE EREHE AEEA SEEE 12 Attaching the Mounting Bracket to the Flat Panel siens 13 Lock It Security Barrel Installation Optional sisi 13 Attaching the Flat Panel to the Wall Plate sienne 14 Mounting Bracket Adjustm nts css aneneeenntatesseutragiens rennbiideteetuntntee dounsdudds cdsnandsavassagnesaises seu tt l Reed taste Ste 14 Leveling Screw Adjustments assena n aa a eaa E a a a e a e pied a a E OR Ei 14 Locking Screw AdjUSIMCNb ics cain nia sia aeolian a a ea S Eaa SE OEE EEE EE ENET RRE 14 AUS A CET QE EE EEE E OA pE aaa 15 Utilizing the Security Bartels sisien e a EEE aE E a ae aE E nee E a E a EAE EEES 15 Technical SpeCfCatiONS ss isa e e a A tied SEEE ed eis E E STEA EEN EEEL ETEN 16 Wanane a a E e e e E a EE E E E sanahatena cued 17 Weight Limit THE WALL STRUCTURE MUST BE CAPABLE OF AIEEE ene SUPPORTING AT LEAST FIVE TIMES THE WEIGHT OF Sea ara TARE eee 15 S THE FLAT PANEL IF NOT THE WALL STRUCTURE MUST BE REINFORCED
17. ting Cable Electrical Cut Out A large cut out on the wall plate allows for easy cable access and power distribution installations 4 Directional Mounting Arrow Directional Mounting Arrow lets you know which edge is up Z Low Profile Design Holds the flat panel less than 2 from the wall Mounting Slots Allow for a variety of stud configurations and lateral shift adjustments when mounting your flat panel COCOCOCECOCOCOOCCO6 GC Locking Safety Screws Prevents the flat panel from being removed or dislodged from the wall plate we Universal Spacers Premier Mount s uniquely designed spacers that fit multiple screw sizes Installation Instructions Visit the Premier Mounts website at http www premiermounts com Page 5 b 4 24 P4263T Installing the Wall Plate Introduction itt Directional Mounting Arrow The Directional Mounting Arrow stamped into the top of the P4263T wall mount indicates which edge is the top Mounting Safety Two people are recommended to for the installation of this mount 000000000000000000000C TB ark Cc Ur Tru Determining the Mounting Surface If you will be installing your P4263T mount to wood studs proceed to the Wood Stud Installation section If you will be installing your P4263T mount to a concrete wall
18. tion Level the wall plate Use a pencil and mark 2 upper and 2 lower mounting locations where you will be drilling holes for the concrete wedge anchors Each horizontal location cannot be closer than 12 apart Set the wall plate to one side in a safe location Use a power drill and 5 6 concrete drill bit to drill a hole at each of the marks Page 8 Visit the Premier Mounts website at http www premiermounts com Installation Instructions b a P4263T 24 Installing the Wall Plate contd Insert a concrete wedge anchor into each hole If necessary lightly tap each concrete wedge anchor into place with a hammer Remove the nuts and washers from all four 4 concrete wedge anchors Replace the washers which you removed from the concrete wedge anchors with the washers shown in the parts list on Page 3 Place the wall plate against the wall over the threaded shafts of the concrete wedge anchors Attach the nuts and washers to each of the concrete wedge anchors and tighten using a socket wrench and an M10 socket Do not overtighten the wedge anchor nuts Proceed to the Installing the Mounting Bracket section Steel Stud Installation The supplied M6 steel stud anchors must be used to install your Premier Mounts mount to steel studs Do not use lag bolts or wood screws Steel Stud Anchor Screw Steel Stud Anchor Sleeve
19. u are certain that top and bottom hooks of both mounting brackets are securely seated on the upper and lower mounting rails of the wall panel Raise the flat panel past the top and bottom mounting rails on the wall panel Slide the flat panel down slowly keeping it close to the wall Engage the top and bottom mounting brackets to the rails of the wall plate Proceed to the Mounting Bracket Adjustments section Mounting Bracket Adjustments Leveling Screw Adjustment If your flat panel is tilted too far to one side the leveling screws will allow you compensate for this tilt by simply adjusting the screws with a screwdriver Loosen both locking screws Adjust the tilt of your flat panel Tighten both locking screws Caution It is possible to dislodge your flat panel while you level your flat panel Use extreme caution until you tighten the locking screws Locking Screw Adjustment After you have finished leveling your flat panel be sure to tighten the two 2 M6 x 35mm locking screws A Do not overtighten the locking screws M6 x 30mm Leveling Screw 1 per Bracket M6 x 35mm Locking Screw 1 per Bracket COOCCOCOCOOCE0OOOC Page 14 Visit the Premier Mounts website at http www premiermounts com Installation Instructions 4 P4263T 24 Tilt Adjustment Adjusting the Flat Panel Friction Tilt Angle Place
Download Pdf Manuals
Related Search