Gefen GTV-WHD-1080P-LRS-BLK
Contents
1. Setup TIP Use the DELETE button on the IR Remote Control to jump directly to the Select Video Source menu when deleting sources 22 OPERATING THE WIRELESS FOR HDMI 11 The Connecting to status message will be displayed Connecting to DVR 12 After a few moments the selected source signal will be displayed sas Connected to DVR n Y mm FEET I Eur ge BE NOTE The video source will always need to be selected even if the source currently being viewed is not deleted 23 OPERATING THE WIRELESS FOR HDMI Disconnecting the Wireless Link The Wireless for HDMI network can be completely disconnected if necessary This can be used in order to restrict the source from being viewed 1 Point the IR Remote Control at the Receiver unit and press the MENU button 2 Select Disconnect Wireless Link and press the OK button Setup Add new Video Source gt Remove Video Source gt Modify Video Source Name gt Disconnect Wireless Link 3 After a few seconds the screen will go blank A status message indicating that the wireless has been turned off will be displayed The Wireless for HDMI network is now in standby mode Wireless Off 24 OPERATING THE WIRELESS FOR HDMI Reconnecting the Wireless Link 1 Press the Source button on the IR Remote Control The Connecting to message will be displayed Connecting to DVR2. HOM 1080P PROGRESSIVE Wireless for HDMI Multi Room Solution GTV WHD 1080P LR BLK User Manual gefen com ASKING FOR ASSISTANCE Technical Support Telephone 818 772 9100 800 545 6900 Fax 818 772 9120 Technical Support Hours 8 00 AM to 5 00 PM Monday through Friday Pacific Time Write To Gefen LLC c o Customer Service 20600 Nordhoff St Chatsworth CA 91311 www gefen com support gefen com Notice Gefen LLC reserves the right to make changes in the hardware packaging and any accompanying documentation without prior written notice Wireless for HDMI Multi Room Solution is a trademark of Gefen LLC HDMI the HDMI logo and High Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing in the United States and other countries O 2014 Gefen LLC All rights reserved All trademarks are the property of their respective owners Rev A9 CONTENTS 1 Introduction 2 FCC Statement 3 Operation Notes 5 Features 6 Panel Layout 6 Sender Unit 7 Receiver Unit 8 Panel Descriptions 8 Sender Unit 8 Receiver Unit 9 IR Remote Control Unit 9 Layout and Descriptions 10 Connecting the Wireless for HDMI 10 Wiring Diagram 10 Operating the Wireless for HDMI 11 The Linking Process 12 Using Multiple Sender units 12 Adding a New Video Source 15 Renaming Sources 18 Switching between Sources 20 Deleting Sources 24 Disconnecting the Wireless Link 25 Recom
3. Remote Control to bypass the Select Video Source menu and directly switch to another Sender unit 19 OPERATING THE WIRELESS FOR HDMI Deleting Sources If a Sender unit source will no longer be necessary it can be removed from the Wireless for HDMI network 1 Point the IR Remote Control at the Receiver unit and press the MENU button Setup Add new Video Source gt Remove Video Source Modify Video Source Name Disconnect Wireless Link 2 Select Remove Video Source from the Setup menu using the cursor buttons on the IR Remote Control Setup gt Add new Video Source gt Remove Video Source Modify Video Source Name Disconnect Wireless Link 20 OPERATING THE WIRELESS FOR HDMI 3 Click the OK button to confirm the selection 4 The Chose Source to Remote menu will be displayed 5 Select the source to be removed and press the OK button Choose Source to Remove gt STB 6 Press the OK button to confirm the removal of the selected device Removing BluRay Press OK to continue or Exit to cancel 7 After a few seconds the screen will go blank 21 OPERATING THE WIRELESS FOR HDMI 8 Press the SOURCE button to display the Select Video Source menu Select Video Source gt DVR Setup 9 Select the desired source using the cursor buttons Then press the OK button to confirm the selection Select Video Source gt STB gt DVR
4. The Wireless for HDMI Multi Room Solution does not support DVI devices Connect the included 5V DC power supplies to the Sender and Receiver unit and connect them to available electrical outlets OPTIONAL Connect the included IR emitter to the Sender unit and place it near the IR sensor of a source device to be controlled To control the IR source connected to the Sender unit point the source s IR remote at the IR sensor on the Receiver unit The Link and Video LED indicators on both the Sender and Receiver unit will glow bright blue to indicate a successful connection between the Sender and Receiver unit Ordinarily no pairing is required out of the box However the Sender and Receiver can also be paired manually if needed Wiring Diagram for the Wireless for HDMI Multi Room Solution Gefen ty HDMI CABLE A Sender a GTV WHD 1080P LR 10 OPERATING THE WIRELESS FOR HDMI The Linking Process After all the connections have made see page 10 to the Wireless for HDMI the Receiver unit will attempt to negotiate with the Sender unit Status Message Provides information on the current status of the Wireless for HDMI Connecting to Sender After a few moments the source signal will appear on the display The status message will disappear after a few seconds Connected to Sender 11 OPERATING THE WIRELESS FOR HDMI Using Multiple Sender Units The Wireless for HDMI can be used with up
5. e Consult the dealer or an experienced radio TV technician for help In order to maintain compliance with FCC regulations shielded cables must be used with this equipment Operation with non approved equipment or unshielded cables is likely to result in interference to radio and TV reception The user is cautioned that changes and modifications made to the equipment without the approval of the manufacturer could void the user s authority to operate this equipment OPERATION NOTES READ THESE NOTES BEFORE INSTALLING OR OPERATING THE GEFENTV WIRELESS FOR HDMI MULTI ROOM SOLUTION Maximum extension distance is 100 feet 30 meters with a clear line of sight Supported resolutions 1080p60 1080p50 1080p24 1080i60 1080i50 720p60 720p50 576p50 480p60 no SD resolution on LR O NOTE The Wireless for HDMI Multi Room Solution does not support Standard Definition resolutions VESA 1600x1200 1366x768 1280x1024 1024x768 800x600 640x480 Obstructions such as walls and furniture may reduce performance and reception distance DVI D Support Gefen recommends placing both units into the provided stands with the Gefen logo pointing down to help maintain the strongest possible transmission signal Interference caused by other RF products may reduce performance and reception distance Use with multiple Sender units Can be used with a single Receiver unit to provide source switching capability U
6. max 8W max Dimensions Sender Receiver W XH x D 5 83 x 0 8 x 3 8 148mm x 20mm x 96mm Shipping Weight rinni 22422 2 8 lbs 1 27 kg All features and specifications are subject to change without notice 28 WARRANTY Gefen warrants the equipment it manufactures to be free from defects in material and workmanship If equipment fails because of such defects and Gefen is notified within two 2 years from the date of shipment Gefen will at its option repair or replace the equipment provided that the equipment has not been subjected to mechanical electrical or other abuse or modifications Equipment that fails under conditions other than those covered will be repaired at the current price of parts and labor in effect at the time of repair Such repairs are warranted for ninety 90 days from the day of reshipment to the Buyer This warranty is in lieu of all other warranties expressed or implied including without limitation any implied warranty or merchantability or fitness for any particular purpose all of which are expressly disclaimed 1 Proof of sale may be required in order to claim warranty 2 Customers outside the US are responsible for shipping charges to and from Gefen 3 Copper cables are limited to a 30 day warranty and cables must be in their original condition The information in this manual has been carefully checked and is believed to be accurate However Gefen assumes no respon
7. 2 After a few seconds the wireless link will be restored and the source signal will be displayed 25 OPERATING THE WIRELESS FOR HDMI Power Down Mode The Wireless for HDMI can be powered down when not in use 1 Point the IR Remote Control at the Receiver unit and press the GUEST button 2 After a few seconds the screen Receiver and Sender unit s will power down A status message indicating that the Wireless for HDMI has been powered down will be displayed Powering Down 26 OPERATING THE WIRELESS FOR HDMI 3 After the Wireless for HDMI has been successfully powered down the Wireless Off message will be displayed on the screen Wireless Off Powering Up after a Power Down 1 Point the IR Remote Control at the Receiver unit and press the GUEST button 2 The Connecting to message will be displayed 3 After a few moments the selected source signal will be restored A Connected to DVR lt Li 27 SPECIFICATIONS Operating Frequency agenda dis 5 GHz Supported resolutiOnS acsoricmimaanacaa pres 480p to 1080p Video Input Connector Sender 1 HDMI Type A 19 pin female Video Output Connector Receiver 1 HDMI Type A 19 pin female USB Connector Receiver 1 Mini B factory use only Power Supply Sender Receiver nenne 2 5V DC Power Consumption Sender Receiver 8W
8. I Operational Limitations Regarding US and EU models note that all RF devices are designed by compliance regulation to accept interference from all other devices Operation of wireless products is therefore dependent on the environment they are in Other RF products even ones that seemingly might not be in the frequency range do create harmonics and other artifacts that could interfere with the operation of the Wireless for HDMI FEATURES HDMI Features Supported e LPCM digital audio streams up to 7 1 channels are supported e Dolby TrueHD and DTS HD Master Audio streams up to 5 1 channels are supported e 3DTV pass through HDCP pass through e 12 bit Deep Color e Lip Sync pass through Features e Wireless extension of HDMI up to 100 feet 30 meters e Supports resolutions up to 1080p Full HD No Latency e AES128 encryption IR Back Channel provides IR control from the viewing location to the source Up to 8 Senders can be accessed by a Receiver e Included IR remote allows switching between three Sender units WHDI 1 0 FCC Part 15 and ETSI compliant e Uncompressed High Definition A V from source to display e Additional Sender units available separately Package Includes 1 1 2 1 1 2 2 1 Wireless for HDMI Multi Room Solution Sender unit Wireless for HDMI Multi Room Solution Receiver unit 5 ft HDMI cables M M IR Remote Control IR Emitter Cradles for Sender and Rec
9. a few moments the source signal connected to the additional Sender unit will be displayed Connected to Sender 8 If desired repeat steps 1 7 to add another Sender unit to the Wireless for HDMI network TIP Use the ADD button see page 9 on the IR Remote Control to bypass the Setup menu and jump directly to registering the Sender unit 14 OPERATING THE WIRELESS FOR HDMI Renaming Sources By default each Sender unit is assigned the name Sender This can be confusing when multiple Sender unit are used However this identifier can be changed to reflect for example the source to which each Sender unit is connected 1 Point the IR Remote Control at the Receiver unit press the MENU button select Modify Video Source Name then press the OK button Setup Add new Video Source gt Remove Video Source gt Modify Video Source Name Disconnect Wireless Link 2 Select the source to rename from the menu by using the cursor keys Choose Source to Rename gt Sender gt Sender OPERATING THE WIRELESS FOR HDMI The Rename Video Source Name menu will be displayed along with the selected Source Use the A and Y cursor keys to change the highlighted character The A key moves forward within the list of available characters and the Y key moves backward through the list The list of available characters is listed in the table below The first character first row first column is a
10. display Point the source s IR remote at the IR window on the Receiver unit to control the source that is placed near the Sender unit FCC STATEMENT This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation INSTRUCTION TO THE USER This equipment has been tested and found to comply with the limits for a class B digital device pursuant to part 15 ofthe FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and Receiver unit e Connect the equipment into an outlet on a circuit different from that to which the Receiver unit is connected
11. eiver units 5V 2A DC Power Supplies Quick Start Guide vere ve ve wv All features and specifications are subject to change without notice 5 Front PANEL LAYOUT Sender unit Back PANEL LAYOUT Receiver unit yuol4 PANEL DESCRIPTIONS Sender Unit Pairing button Press and hold this recessed button using a paper clip for approximately 3 seconds to pair the Sender unit with the Receiver unit Link This LED indicator will glow bright blue once a link is established between the Sender unit and the Receiver unit Video This LED indicator will glow bright blue once a video link is established between the Sender unit and the Receiver unit IR Connect the included IR Emitter to this port and place it near the IR sensor of the source device to be controlled HDMI In This input will accept a single HDMI source device Power Connect the included 5V DC power supply to this receptacle Receiver Unit Pairing button Press and hold this recessed button using a paper clip for approximately 3 seconds to pair the Sender unit with the Receiver unit IR Sensor Receives IR commands from the included IR Remote Control unit and the IR remote of the source unit to be controlled Link This LED indicator will glow bright blue once a link is established between the Receiver unit and the Sender unit Video This LED indicator will glow bright blue once a video link is established between the Receive
12. necting the Wireless Link 26 Power Down Mode 27 Powering Up after a Power Down 28 Specifications 29 Warranty INTRODUCTION Congratulations on your purchase of the GefenTV Wireless for HDMI Your complete satis faction is very important to us About Gefen We specialize in total integration for your home theater while also focusing on going above and beyond customer expectations to ensure you get the most from your hardware We invite you to explore our distinct product line Please visit http www gefen com for the latest offerings in High Definition signal solutions or call us between the hours of 8 00 am and 5 00 pm Monday Friday Pacific Standard Time for assistance with your A V needs We ll be happy to assist you The GefenTV Wireless for HDMI Multi Room Solution The GefenTV Wireless for HDMI Multi Room Solution sends high definition audio and video to any HDTV display up to 100 feet 30 meters away It extends HDMI from computers set top boxes Blu ray players and other audio video sources to a remote HDTV display The Wireless for HDMI Multi Room Solution supports resolutions up to 1080p Full HD along with support for up to 7 1 channels of LPCM and up to 5 1 channels of Dolby TrueHD and DTS HD Master Audio The included IR emitter can be connected to the Sender unit and placed by the Hi Def source allowing full control of the source from another room simply by pointing the IR remote at the Receiver unit The Wirele
13. p to 8 Senders are supported Local RF interference can limit the number of Sender units that can be used Each Sender unit needs to be placed at least 1 meter apart for optimum performance US Models Up to 4 pairs of Sender and Receiver units can be operated in the same environment Local RF interference can limit the number of units that can be used Each Sender unit needs to be placed at least 1 meter apart for optimum performance If additional Sender Receiver pairs are to be used each set of units must be placed beyond the reception range 100 feet 30 meters of the other in order to prevent interference Continued on next page 3 OPERATION NOTES Continued from previous page EU Models Up to 2 pairs of Sender and Receiver units can be operated in the same environment Local RF interference can limit the number of units that can be used Each Sender unit needs to be placed at least 1 meter apart for optimum performance If additional Sender Receiver pairs are to be used each set of units must be placed beyond the reception range 100 feet 30 meters of each other in order to prevent interference IR back channel compatibility N IMPORTANT Only products with 38 kHz IR carrier frequency are compatible If in doubt please check with the equipment manufacturer Due to complexity in some manufacturers IR codes not all 38kHz IR devices may be compatible with the IR Back Channel of the Wireless for HDM
14. r unit and the Sender unit USB Mini USB service port for factory use only HDMI Out Connect the included HDMI cable from this connector to an HD display Power Connect the included 5V DC power supply to this receptacle IR REMOTE CONTROL UNIT Layout and Descriptions MENU EXIT SOURCE 1 ORIG 9 AN 8 Gs 49 a 3 V Z INPUT DEVICES D Menu Press this button to display the Setup menu Cursor buttons Used to control Left Up Right and Down cursor motion within a menu system OK Press this button to accept the current operation or menu selection Delete When using multiple Sender units press this button to delete a Sender unit from the wireless network Input Devices When using multiple Sender units use these buttons to select any of the first three linked Sender units Use the Source button to select Senders 4 8 Guest Powers down the wireless system Add When using multiple Sender units press this button to add a Sender unit source Exit Press this button to cancel an operation or exit any menu system Source When using multiple Sender units sources press this button to select a different Sender unit 9 CONNECTING THE WIRELESS FOR HDMI How to Connect the Wireless for HDMI Multi Room Solution Connect a Hi Def source to the Sender unit using the included HDMI cable Connect an HD display or projector to the Receiver unit using the included HDMI cable O NOTE
15. sibility for any inaccuracies that may be contained in this manual In no event will Gefen be liable for direct indirect special incidental or consequential damages resulting from any defect or omission in this manual even if advised of the possibility of such damages The technical information contained herein regarding the features and specifications is subject to change without notice For the latest warranty coverage information refer to the Warranty and Return Policy under the Support section of the Gefen Web site at www gefen com PRODUCT REGISTRATION Please register your product online by visiting the Register Product page under the Support section of the Gefen Web site 29 Rev A9 080P LRx MA GTV WHD 1 20600 Nordhoff St Chatsworth CA 91311 1 800 545 6900 818 772 9100 fax 818 772 9120 www gefen com support gefen com Du O ce amp This product uses UL listed or CE compliant power supplies We
16. space and can be used anywhere in the name The maximum length of the Source name cannot exceed nine characters including any spaces Figure 2 Available characters for source naming Rename Video Source Name lender Use the 4 and gt cursor keys to select the character in the name to be changed 16 OPERATING THE WIRELESS FOR HDMI 4 After the video source has been renamed press the OK button to save the changes Select Video Source Sender Setup 17 OPERATING THE WIRELESS FOR HDMI Switching between Sources Once two or more Sender units have been connected to a Receiver unit use the IR Remote Control unit to switch between each source 1 Point the IR Remote Control at the Receiver unit and press the Source button The Select Video Source menu will be displayed Select Video Source gt STB 2 Use the Cursor buttons on the IR Remote Control to select the desired source Select Video Source gt STB 18 OPERATING THE WIRELESS FOR HDMI 3 Once the desired source has been selected press the OK button Select Video Source 4 The screen will go blank momentarily and the Connecting to status message will be displayed indicating that the Receiver unit is switching to the selected Sender unit source 5 After a few moments the selected source signal will be displayed Connected to Sender TIP Use the INPUT DEVICES buttons see page 9 on the IR
17. ss for HDMI Multi Room Solution transmits through walls and does not require line of sight for good reception Additional features allow multiple units using the included handheld remote control How It Works Connect one of the included HDMI cables from the Hi Def source to the Sender unit Connect the other included HDMI cable from the Receiver unit to the HDTV display Connect the included power supplies to the Sender and Receiver units and to available electrical outlets Connect the included IR Emitter to the Sender unit and place it near the IR sensor window of the device to be controlled Power up the source and the display Within approximately one minute the Video indicators on both units should now glow solid blue to indicate a successful connection between the Sender and Receiver unit If the Sender and Receiver units do not pair automatically the LEDs on the Sender will continue to blink Navigate through the on screen menu and have the Receiver unit look for a Sender unit If the remote is not available you can press and hold the recessed pairing button on the Receiver with a paper clip until its Link LED stops blinking and goes dark Press and hold its recessed pairing button on the Sender unit with a paper clip until the Link LED stops blinking and goes dark If navigating the menu using the remote press the OK button on the IR remote A message indicating that the Sender and the Receiver units have been paired will appear on the
18. to eight Sender units to provide switching capability between Sender units Figure 1 Receiver unit with multiple Sender units Adding a new Video Source Before adding an additional Sender unit to the Wireless for HDMI network make sure that a single Sender Receiver pair function correctly 1 2 Connect the Sender unit to a Hi Def source using an HDMI cable Connect the power supply to the Sender unit Point the IR Remote Control at the Receiver unit and press the MENU button The Setup menu will be displayed Setup gt Remove Video Source Modify Video Source Name Disconnect Wireless Link 12 OPERATING THE WIRELESS FOR HDMI 4 Use the cursor buttons on the IR Remote Control to select Add new Video Source from the Setup menu 5 Press the OK button The following message will be displayed Press and hold the Link button on Sender until Link LED stops blinking 6 Press and hold down the Pairing button see pages 6 8 on the Sender unit for about 5 seconds Adding Sender Press OK to continue or Exit to cancel 7 Press the OK button to continue adding the Sender unit NOTE When pairing multiple Senders it is recommended that you rename the ones already linked to avoid confusion 13 OPERATING THE WIRELESS FOR HDMI As the Sender unit is added to the Wireless for HDMI network a progress bar will be displayed Adding Sender oo After
Download Pdf Manuals
Related Search