StarTech.com HDMI Over CAT5/CAT6 Extender with Power Over Cable - 165 ft (50m)
Contents
1. networking equipment i e router switch OR If you are using premises cabling ensure that the Category 5 unshielded twisted pair UTP network cabling between the Host Unit and theRemote Unit has been properly terminated in a wall outlet in each location and there is a patch cable long enough to connect the Remote Unit and the Host Unit to their respective outlets The cabling should not go through any networking equipment i e router switch Starlechs 4 Hard to find made easy Instruction Manual C Connect the other end of the Cat5e 6 cable from LINK OUT A to the LINK IN A RJ 45 connector on the Receiver Unit d Connect the other end of the Cat5e 6 cable from LINK OUT B to the LINK IN B RJ 45 connector on the Receiver Unit NOTE If using Cat6 cables extension distance is limited to 40m 130 ft 3 Install Receiver Unit a Position the Receiver Unit near the video display i e television projector b Connect the video source to the HDMI OUT on the Receiver Unit using an HDMI cable C Optional If you ve chosen to power the kit from the Receiver side connect the provided power supply 4 Your source video image will now appear on the remote video display Operation Video Adjustment Receiver Unit Only This function allows adjustments in sharpness of the video image for better clarity If necessary adjust the EO Selector at the Receiver Unit to compensate cable length Turn the EQ Selector one no2. ID Configuration EDID Copy EDID Ghost While using only one CATx cable it is suggested applying EDID Copy first Step 1 Use CATx cable for connection between Tx amp Rx on Aux RJ 45 Jack Apply power to Receiver Unit Step 2 Connect the monitor EDID compliant to Video Out on the Receiver Unit and power on the monitor Step 3 Press the button EDID Copy on Transmitter Unit and release the button RIGHT AFTER the LED flashes green Step 4 The LED flashes green amp red and then it lights blue indicating copy successfully Otherwise if the LED flashes RED it means that a The monitor is not properly connected b The monitor is not powered on c EDID data of the monitor is not applicable Try to repeat Step 3 to 4 again Starlech 6 Hard to Find made easy Instruction Manual EDID Factory Default Setting To avoid confusion in which EDID information has been copied or for more purposes this function enables to reset the state to factory default Step 1 Use CATx cable for connection between Tx amp Rx on Aux RJ 45 Jack Apply power to Receiver Unit Step 2 Press the button EDID Copy and release the button RIGHT AFTER the LED flashes red Step 3 The LED flashes green amp red indicating default setting successfully DDC Pass Mode Press the button for more than 15 sec and release right after the LED flashes green The LED lights blue indicating setting successfully To exit this mode follow EDID Fact
3. ea AUN ONY as ccs erasatrcas sets vensaaescacsgvsavaycureven ERT 4 edger Sys aee geli Eo oO nnn eer sere mere ee ere 4 Hardware installation icio ta th rtt tni ertcetustuc dido tert E s ap Rer pU at 4 IO e M a 5 Video Adjustment Receiver Unit Only eee eese ee teeeten een ttnnttonttnntenttnntis 5 SB Pieces perme et een RR Uno e E eee 6 SBSEIITCAt ONS ects ctccc css ee cczscuceses suet nar ir Ei ENET E 8 Technical SUDDOEL sessdveussoniscesnatadcscsssieratuiadestemneisianmana renee 9 Warranty Information ssesssosessecssoesssocesocessocesseessoosesocesoosesseessoeessosesse 9 Starlechs i Hard to find made easy Instruction Manual Product Diagram Top View Ser Tech 1 LED Indicator 1 LED Indicator 2 EDID Copy Button 2 EQ Selector Rear View 1 Power Jack 1 Power Jack 2 HDMI In 2 HDMI Out Front View 1 LINK OUT A RJ 45 Connector 1 LINKIN A RJ 45 Connector 2 LINK OUT B RJ 45 Connector 2 LINK IN B RJ 45 Connector Instruction Manual ota Tech AI 1 Hard to find made easy Introduction The ST121SHD50 HDMI over CAT5e 6 Video Extender kit lets you extend HDMI video and audio up to 165 feet 50 Meters 1080i over 2 CAT5e Ethernet cables or up to 130 Feet 40 Meters 1080p over 2 CAT6 Ethernet cables For added versatility both the Transmitter and Receiver can be powered by the same single power source using Power Over Cable POC With suppo
4. loss arising out of or related to the use of the product exceed the actual price paid for the product Some states do not allow the exclusion or limitation of incidental or consequential damages If such laws apply the limitations or exclusions contained in this statement may not apply to you Starlechs 9 Hard to Find made easy Instruction Manual StarTechg Hard to find made easy Hard to find made easy At StarTech com that isn t a slogan It s a promise StarTech com is your one stop source for every connectivity part you need From the latest technology to legacy products and all the parts that bridge the old and new we can help you find the parts that connect your solutions We make it easy to locate the parts and we quickly deliver them wherever they need to go Just talk to one of our tech advisors or visit our website You ll be connected to the products you need in no time Visit www startech com for complete information on all StarTech com products and to access exclusive resources and time saving tools StarTech com is an ISO 9001 Registered manufacturer of connectivity and technology parts StarTech com was founded in 1985 and has operations in the United States Canada the United Kingdom and Taiwan servicing a worldwide market
5. ory Default Setting steps Instruction Manual sta lech 7 Hard to find made easy Specifications Instruction Manual 1x HDMI 19 pin Female 2x RJ 45 Female 1x HDMI 19 pin Female 2x RJ 45 Female StarTechg o Hard to find made easy Technical Support StarTech com s lifetime technical support is an integral part of our commitment to provide industry leading solutions If you ever need help with your product visit www startech com support and access our comprehensive selection of online tools documentation and downloads For the latest drivers software please visit www startech com downloads Warranty Information This product is backed by a two year warranty In addition StarTech com warrants its products against defects in materials and workmanship for the periods noted following the initial date of purchase During this period the products may be returned for repair or replacement with equivalent products at our discretion The warranty covers parts and labor costs only StarTech com does not warrant its products from defects or damages arising from misuse abuse alteration or normal wear and tear Limitation of Liability In no event shall the liability of StarTech com Ltd and StarTech com USA LLP or their officers directors employees or agents for any damages whether direct or indirect special punitive incidental consequential or otherwise loss of profits loss of business or any pecuniary
6. otarfechg or Hard to find made easy HDMI over Cat 5e 6 Extender 50m ST121SHD50 o7 z COM actual product may vary from photos DE Bedienungsanleitung de startech com FR Guide de l utilisateur frstartech com ES Gu a del usuario es startech com IT Guida per l uso it startech com NL Gebruiksaanwijzing nl startech com PT Guia do usu rio pt startech com For the most up to date information please visit www startech com Manual Revision 01 31 2014 FCC Compliance Statement This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circui
7. rt for resolutions up to 1920x1080 and the accompanying digital audio this HDMI extender is a plug and play solution that can easily be installed using new or existing Ethernet infrastructure wiring Backed by a StarTech com 2 year warranty and free lifetime technical support Packaging Contents 1x HDMI over CAT5e 6 UTP Transmitter 1x HDMI over CAT5e 6 UTP Receiver e 1x Universal Power Adapter EU UK NA e 2x Mounting Brackets 2xFoot Pad Set e 1x User Manual System Requirements e HDMI enabled video source device i e computer Blu ray Player e HDMI enabled display device i e television projector e Available AC electrical outlet for either the transmitter or receiver e HDMI cables for Receiver and Transmitter Starlechs 2 Hard to Find made easy Instruction Manual LED Indicator Status Transmitter em i MED ERI eee HDMiEDiDcontentconfigured Emit blue with green flashing three times See a a ERRORES UT n Rn M ECHTE RN ON ME NN t is suggested replacing cables with better quality ones if the LED emits blue without video displaying The emitting period of purple LED depends on connected device The LED emits steady blue indicating that the video signal is detected by Receiver StarTe chs Om 3 Hard to find made easy Instruction Manual Installation Preparing Your Site 1 Determine where the local video source i e computer Blu ray Player will be located and set
8. t different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help Use of Trademarks Registered Trademarks and other Protected Names and Symbols This manual may make reference to trademarks registered trademarks and other protected names and or symbols of third party companies not related in any way to StarTech com Where they occur these references are for illustrative purposes only and do not represent an endorsement of a product or service by StarTech com or an endorsement of the product s to which this manual applies by the third party company in question Regardless of any direct acknowledgement elsewhere in the body of this document StarTech com hereby acknowledges that all trademarks registered trademarks service marks and other protected names and or symbols contained in this manual and related documents are the property of their respective holders Starlech Hard to find made easy Instruction Manual Table of Contents Product Dia Fain secos sitit RR FEO UN FUREU URN UM EIS EH DRM 1 i p e abetting een tes 1 Per MEW PRONTI NINE TR MEORUM REUS ORENSE ER RD RTT TREE 1 iie VAS m 1 Juldgofe V aiu a LENTES RTT 2 Paciegepicri OPES DIES momen enitn ie Henri ta re caf Ct Piin eH etched n 2 Sy Eee T 2 LED Indicato niniin E ee EA 3 BENS G
9. tch at one time and wait for 10 12 sec For HDMI cable length Rx to monitor less than 8 meters the selector position is around 0 7 depends on video resolution For HDMI cable length Rx to monitor greater than 8 meters the selector position is around 8 9 A F depends on video resolution For example if using a 1 8M or 3 0M HDMI cable a CAT5 cable and a display with resolution of Full HD 1920 x 1080 you may adjust video according to its CAT5 cable length as following CAT5 Cable Length EQ Selector Position DENDO S M TTE DN Se ee ee ee Starlech 5 Hard to Find made easy Instruction Manual The following is the test result while using different types of CATx cables Cable Type Resolution Cable Length max 1080i 50M CAT6 1080p 40M CATS ne te E ee solid 1080p 20M CATS ME b NES io S stranded 1080p 16M EDID Configuration In some cases display problems may occur due to incorrect EDID communication between the display monitor and the unit or inappropriate EDID data programmed by display manufactures This EDID Copy feature allows the system either automatically provide the necessary EDID to display or manually copy EDID from EDID compliant displays via push button Auto EDID Configuration The system can automatically read EDID from your display while two RJ 45 ports Video amp Aux are in connection Manual ED
10. up the device 2 Determine where the remote display will be located and place mount the display appropriately NOTE This HDMI extender kit features Power over cable allowing both the Transmitter and Receiver to be powered from a single power source that can be connected at either end of the connection Please ensure that either the Transmitter or the Receiver Unit is situated near an available AC electrical outlet Make sure all devices are turned off before beginning installation Hardware Installation 1 Install Transmitter Unit a Position the Transmitter Unit near the video source i e Computer Blu ray Player b Connect an HDMI cable from the video source device i e computer Blu ray Player to the HDMI IN on the Transmitter Unit C Optional If you ve chosen to power the kit from the Transmitter side connect the provided power supply 2 Install RJ45 terminated Cat5e 6 Ethernet Cables a Connect an RJ45 terminated Cat5e 6 Ethernet cable not included to the LINK OUT A RJ 45 connector on the Transmitter unit b Connect another RJ45 terminated Cat5e 6 Ethernet cable not included to the LINK OUT B RJ 45 connector on the Transmitter unit NOTE If you are using surface cabling ensure you have enough Category 5e unshielded twisted pair UTP network cabling to connect the Host Unit to the Remote Unit s location and that each end is terminated with a RJ45 connector The cabling should not go through any
Download Pdf Manuals
Related Search