Ergotron WorkFit-B
Contents
1. ERGOTRON WorkFit B LD For service and warranty visit www ergotron com Si desea informaci n de servicio y garant a visite www ergotron com Pour toute question concernant la garantie ou le service client consultez www ergotron com Weitere Informationen zu Service und Gew hrleistung erhalten Sie unter www ergotron com Ga voor service en garantie naar www ergoton com Per assistenza e la garanzia visitare www ergotron com Ga in pa www ergotron com for service och garanti CAB EOGSEIC OU THLE www ergotron com Zr Cs J Vs AKIRS AME VIA www ergotron com GA www ergotron com USA 1 800 888 8458 Europe 31 0 33 45 45 600 China 86 769 86018920 www ergotron com User s Guide English Guia del usuario Espanol Manuel de l utilisateur Francais Gebruikersgids Nederlands Benutzerhandbuch Deutsch Guida per l utente Italiano Anvandarhandbok svenska DBBOnan sap 0000 00 32 824mm RECTANGLE SHAPED WORKSURFACE jes A 5 60 lbs 6 8 27 2 kg 31 5 48 ae 800 1219 mm Important You will need to adjust this product 080 175 5 after installation is complete Make sure all your 20 44 mm Ee equipment is properly installed on the product al before attempting adjustments This product OTHER SHAPED WORKSURFACE should move smoothly and easily through the full range of motion and stay where you set it If gt movements are too easy o2. and may result in equipment damage and or personal injury If the phillips head stop screw is not installed in this location contact customer care before continuing with installation IMPORTANT Save this stop screw and instructions Install stop screw when shipping or storing this product Failure to follow these instructions may cause lift engine to expand rapidly and may result in equipment damage and or personal injury DO NOT REMOVE SCREW xx Minimize Lift Strength BEFORE Removing Mounted Equipment Shipping the Cart Storing the Cart Install Stop Screw BEFORE Shipping the Cart Storing the Cart To Minimize Lift Strength and Install Stop Screw 1 With cart upright lower worksurface to lowest position 2 Turn adjustment nut at bottom of riser counter clockwise until it stops Adjustment may require 40 60 revolutions 3 Install Stop Screw Follow Installation Instructions provided with Cart Failure to heed this warning may result in serious personal injury Cart Must Remain or property damage Upright whenever Stop Screw is not installed Tipping the cart on its side without Stop Screw installed may cause the work surface IQ to disengage and cause serious personal injury and property damage For More information and instructions refer to product guide at www ergotron com or contact Ergotron Customer Care at 1 800 888 8458 827 178 00 888 24 228 G 00 rev B 07 13
3. rapidly and may result in equipment damage and or personal injury 1 Follow instructions in Appendix A to minimize lift strength 2 Push the desk down to its lowest position 3 Insert stop screw at the bottom of leg 4 Once the stop screw has been installed the desk can be shipped or stored Placing the desk on its back or side is not recommended 888 24 228 G 00 rev B 07 13 14 of 15 Set Your Workstation to Work For YOU Configure su estaci n de trabajo para que trabaje para USTED Ajustez votre station de travail en fonction de VOS besoins Richten Sie Ihren Arbeitsplatz so ein dass er f r SIE arbeitet Stel uw werkstation zo in dat het voor U werkt Approntare la stazione di lavoro nella posizione ergonomica ottimale 1IIIIIIIIIIIIIIIIIIIIIIIIIIIIIII 100000001 I LI 220 508mm Learn more about ergonomic computer use at Mas informacion sobre el uso ergonomico de ordenadores Apprenez en plus sur l utilisation ergonomique d un ordinateur sur Weitere Informationen zur ergonomischen Computernutzung finden Sie unter Leer meer over ergonomisch computergebruik op Per ulteriori informazioni sull uso ergonomico del computer www computingcomfort org Height Position top of
4. screen slightly below eye level To Reduce Fatigue Position keyboard at about elbow height with wrists flat Breathe Breathe deeply through your nose Distance Position screen an arm s length from face at least 20 508mm Blink Blink often to avoid dry eyes Position keyboard close enough to create a 90 angle in elbow Break 2 to 3 minutes every 20 minutes Angle Tilt screen to eliminate glare 15 to 20 minutes every 2 hours Tilt the keyboard back 10 so that your wrists remain flat Altura Coloque el borde superior de la pantalla ligeramente por debajo de la altura de sus ojos Para reducir la fatiga Coloque el teclado aproximadamente a la altura de los codos con las mu ecas planas Respirar Respire hondo por la nariz Distancia Coloque la pantalla a una distancia de un brazo desde la cara esto es unos 50 cm 20 pulgadas Parpadear Parpadee a menudo para que no se sequen Coloque el teclado lo suficientemente cerca para que el codo forme un ngulo de 90 los ojos ngulo Incline la pantalla para eliminar los reflejos Descansar 2 o 3 minutos cada 20 minutos Incline el teclado 10 hacia atr s para que las mu ecas sigan en posici n plana 15020 minutos cada 2 horas Hauteur Positionnez l cran du haut l g rement en dessous du niveau du regard Pour r duire la fatigue Positionnez le clavier peu pr s la m me hauteur que vos coudes pour que vos poignets soient plat Respirez Respirez profond ment par
5. 000000001090 1 L 598909 00001 LI II III IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII 0 I I I III IIIIIIIIIIIIIIIIIIIIIII IL II L 01 IIIIII III II I1LIIIIIIIIIIIIIII II DO 2000002030 L LI LI LI LI IL 10 00 10 III IIIIIIIIIIIIIIIII e 200000 150 200 L LI 1 I IIIIIIIIIL II L I IIIIIIII II III III IIIIIIII1IL LI 00000 OO 00000000 L LI III IIIIIIIIIIL LI O0 00 508 20 OO 000 III IIIII II II 000 Da gagpanadu DU DU 00 200000 20 300 oo O000009 1 00 20000 150 2000 Americas Sales and P 2013 Ergotron Inc Corporate Headquarters EMEA Sales ERGOTRON Al fidis reserved St Paul MN USA Amersfoort The Netherlands While Ergotron Inc makes every effort to provide accurate and complete information on the installation 800 888 8458 31 33 45 45 600 and use of its products it will not be held liable for any editorial errors or omissions including those 1 651 681 7600 www ergotron com made in the process of translation from English to another language or for incidental special or www ergotron com info eu ergotron com consequential damages of any nature resulting from furnishing this instruction and performance of sales ergotron com equipment in connection with this instruction Ergotron Inc reserves the right to make changes in the product design and or product documentation without notification to its users For the most
6. 3 of 15 Components C X DD 4A ne Mu 4x Q D ST3 9 x 16mm Sterile Alcohol Prep 1x DD M2 9 x 7mm gt 0 1 8 3 mm 0 5 32 4mm 1 4 6 5 mm 0 15 32 12 mm 4of 15 888 24 228 G 00 rev B 07 13 Set up Steps 1 RECTANGLE SHAPED WORKSURFACE OTHER SHAPED WORKSURFACE Place template on bottom of work surface Place template on bottom of work surface 1 From side to side align the center mark on the template with 1 From side to side align the center mark on the template with the center of the work surface to ensure maximum stability the center of the work surface to ensure maximum stability 2 From front to back place the center mark on the template 2 From front to back place the center mark on the template 13 15 334 mm from the front of the worksurface 18 9 480 mm from the back of the worksurface 480 mm 13 15 334 mm Centered Centered 888 24 228 G 00 rev B 07 13 5 of 15 Set up Steps Make sure template is located properly and that it is square with the worksurface Then tape the template in place 3 Drill holes into bottom of work surface a Drill the 16x holes into bottom of work surface 3 8 10 mm deep b Drill this 1x hole into bottom of work surface 5 32 4 mm deep TIP To ensure proper depth place a piec
7. crew BEFORE Shipping the Cart Storing the Cart To Minimize Lift Strength and Install Stop Screw 1 With cart upright lower worksurface to lowest position 2 Turn adjustment nut at bottom of riser counter clockwise until it stops Adjustment may require 40 60 revolutions 3 Install Stop Screw Follow Installation Instructions provided with Cart Failure to heed this warning may result in serious personal injury Cart Must Remain or property damage Upright whenever Stop Screw is not installed Tipping the cart on its side without Stop Screw installed may cause the work surface to disengage and cause serious personal injury and property damage For More information and instructions refer to product guide at www ergotron com or contact Ergotron Customer Care at 1 800 888 8458 827 178 00 12 of 15 smooth and easy movements Depending on your product and the adjustment it may take many turns to notice a difference Any time equipment is added or removed from this product resulting in a change in the weight of the mounted load you should repeat these adjustment steps to ensure safe and optimum operation WARNING DO NOT tip desk over to adjust Only perform adjustment while desk is upright Failure to follow these instructions may cause the lift engine to expand rapidly and may result in equipment damage and or personal injury Increase Lift Strength If the mounted weight is too heavy or this product doe
8. current product information or to know if this document is available in languages other than those herein APAC Sales Worldwide OEM Sales please contact Ergotron No part of this publication may be reproduced stored in a retrieval system or transmitted in any form or by any means electronic mechanical photocopying recording or otherwise Tokyo Japan WWW ergotron com without the prior written consent of Ergotron Inc 1181 Trapp Road Eagan Minnesota 55121 USA www ergotron com info cem ergotron com Patents Pending and Patented U S amp Foreign Ergotron is a registered trademark of Ergotron Inc apaccustomerservice ergotron com 888 24 228 G 00 rev B 07 13 15 of 15
9. e of tape on the drill bit TIP To ensure proper depth place a piece of tape on the drill bit 3 8 10 mm from the tip 5 32 4mm from the tip 5 32 4mm 3 8 10 mm 16X 888 24 228 G 00 rev B 07 13 6 of 15 Set up Steps ONLY if you plan to attach any of the WorkFit PD Accessories Drill those holes through the work surface TIP Place something under the worksurface so you don t drill into the surface underneath when you drill these through holes 1 4 6 5 mm 4x 4 Remove the template 888 24 228 G 00 rev B 07 13 7 of 15 Set up Steps esu te ed D vec 6 T EN BRO WE serem co 0 D es ee 8 of 15 Set up Steps a Place the Brake Handle on the work surface at desired location For easy access line b Mark holes to drill up the brake handle flush with the front edge of the worksurface e a Drill holes into bottom of work surface 5 16 8 mm deep b Attach Brake Handle TIP To ensure proper depth place a piece of tape on the drill bit 5 16 8 mm from the tip 4x DDD ST3 9 x 16mm 5 16 8 mm 888 24 228 G 00 rev B 07 13 9 of 15 Set up Steps 10 of 15 Set up Steps 1 1 Q Remove the stop scre
10. o recognize and respond appropriately to Safety problem Alerts should not use this product without adult cian A WARNING indicates either potential for property dam supervision age personal injury or death An Electrical indicates an impending electrical hazard ELECTRICAL which if not avoided may result in personal injury fire and or death ai WARNING IMPACT HAZARD MOVING PARTS CAN CRUSH amp CUT Do not remove the zip tie and card board spacer which keep the hand brake from disengaging until instructed to in the manual Removing the zip tie before the cart is unpacked and standing upright may cause unin tended motion of the riser Failure to heed this warning may lead to WARNING TIPPING HAZARD personal injury or equipment damage When mounting accessories to this product they must stay within the foot print Do not mount accessories past the front and rear worksurface Failure to follow this warning may result in equipment damage and or personal injury 777 24 027 G 00 tapili C 888 24 228 G 00 ICV 8 07 13 20115 WARNING Stop screw is pre installed in this product to secure it in the compressed position during shipping and installation DO NOT REMOVE THIS SCREW UNTIL INSTRUCTED TO DO SO IN THESE INSTRUCTIONS Make sure this screw is in place before starting installation Failure to follow these instructions may cause lift engine to expand rapidly
11. r difficult or if product does not stay in desired positions follow the adjustment instructions to create smooth and easy movements Depending on your product and the adjustment it may take many turns to notice a difference Any time equipment is added or removed from this product resulting in a change in the weight of the mounted load you should repeat these adjustment steps to ensure 0 80 1 75 20 44 mm Total weight of worksurface Wood Worksurface Weight Estimator and mounted equipment must 7 be lt 60 Ibs 27 2 kg Worksurface Estimated Weight safe and optimum operation Worksurface must meet ALL Thickness per square foot dimensional and weight range specification requirements 0 80 20 mm 125 G2 mm WARNING The addition of 1 75 44 mm accessories can negatively impact the tip performance 888 24 228 G 00 rev B 07 13 10f 15 e Hazard Sym bols Review Symbol Signal Word Level of Hazard These symbols alert users of a safety condition that demands attention All users should be able to Y NOTE A NOTE indicates important information that helps you T make better use of this product recognize and understand the significance of the fol lowing Safety Hazards if encountered on the product A CAUTION indicates either potential damage to or within the documentation Children who are not CAUTION hardware or loss of data and tells you how to avoid the able t
12. s not stay up when raised then you ll need to increase Lift Strength Decrease Lift Strength If the mounted weight is too light or this product does not stay down when lowered then you ll need to decrease Lift Strength 888 24 228 G 00 rev B 07 13 APPENDIX A Minimize Lift Strength WARNING Before removing mounted equipment monitor arm stand CPU etc from desk or N to prepare for shipping or storing the desk it is extremely important to minimize the lift strength Failure to install these instructions may cause lift engine to expand rapidly and may result in equipment damage and or personal injury 1 Release the hand brake and move the worksurface up to highest level 2 To minimize lift strength turn adjustment bolt counter clockwise using a 14mm socket Keep adjusting until the wrench stops turning 3 Once at minimum lift strength it is ok to remove mounted equipment WARNING DO NOT tip desk over to adjust Only perform adjustment while desk is upright Failure to follow these instructions may cause the lift engine to expand rapidly and may result in equipment damage and or personal injury 888 24 228 G 00 rev B 07 13 13 of 15 APPENDIX B Inserting Stop Screw WARNING Before shipping or storing the desk or in cases where the desk is placed on it s back or side it is extremely important that the stop screw be re inserted Failure to follow these instructions may cause lift engine to expand
13. t toetsenbord op ongeveer ellebooghoogte met de polsen plat Ademen Adem diep door uw neus in en uit Afstand Plaats het scherm op een armlengte van uw gezicht op ten minste 508 mm 20 in Knipperen Knipper regelmatig om droge ogen te vermi Zet uw toetsenbord zo dichtbij dat u een hoek van 90 in de ellebogen hebt jden Hoek Kantel het scherm om weerspiegeling te elimineren Pauzes nemen 2 tot 3 minuten elke 20 minuten Kantel het toetsenbord 10 naar achteren zodat uw polsen plat blijven liggen 15 tot 20 minuten elke 2 uur Altezza Posizionare la parte superiore dello schermo leggermente sotto il livello degli occhi Per ridurre l affaticamento Posizionare la tastiera circa all altezza dei gomiti in modo che i polsi siano piatti Respirazione Respirare profondamente dal naso Distanza Posizionare lo schermo a un braccio di distanza dal viso almeno a 20 508 mm didistanza Battito delle palpebre Battere spesso le palpebre per Posizionare la tastiera affinch sia abbastanza vicina da costringere i gomiti a un angolo di 90 evitare che gli occhi si asciughino Angolazione Inclinare lo schermo in modo da eliminare i riflessi Pause Fare una pausa di 2 3 minuti ogni 20 minuti Inclinare la tastiera indietro di 10 in modo che i polsi rimangano piatti Fare una pausa di 15 20 minuti ogni 2 ore 01 I II II II I IIIIIIIIIIIIIIIIIIIIIIIII D gagBDagg p gagaapggagauapgapggagpnapggaagapnapbpggoanpubo DU IIIIIIIIIIIIIIIIII 000000
14. votre nez Distance Positionnez l cran un bras de distance de votre visage au moins 508 mm 20 pouces Clignez des yeux Clignez souvent des yeux pour ne pas Positionnez le clavier assez pr s pour que vos coudes forment un angle de 90 avoir les yeux secs Angle Inclinez l cran pour ne pas tre bloui Faites des pauses 2 3 minutes toutes les 20 minutes Inclinez le clavier vers l arri re de 10 pour que vos poignets soient plat 15 20 minutes toutes les 2 heures H he Positionieren Sie die obere Kante des Bildschirms knapp unter Augenh he Vermeiden von Erm dungserscheinungen Positionieren Sie die Tastatur bei flach aufgelegten Handgelenken auf Ellenbogenh he Atmen Atmen Sie tief durch die Nase ein und aus Abstand Positionieren Sie den Bildschirm mindestens eine Arml nge 50 cm von Ihrem Gesicht entfernt Blinzeln Blinzeln Sie so oft wie m glich um trockene Positionieren Sie die Tastatur nahe genug um einen Ellenbogenwinkel von 90 zu erm glichen Augen zu vermeiden Winkel Neigen Sie den Bildschirm so dass ein Spiegeleffekt vermieden wird Pausen Machen Sie alle 20 Minuten eine Pause von Neigen Sei die Tastatur um 10 nach hinten sodass Ihre Handgelenke flach aufliegen 2 3 Minuten Machen Sie alle 2 Stunden eine Pause von 15 20 Minuten Hoogte Zet de bovenkant van het scherm iets boven ooghoogte Om vermoeidheid te verminderen Plaats he
15. w to allow the worksurface to raise and lower before installing equipment IMPORTANT Save this stop screw and instructions Install stop screw when moving shipping or storing this product Failure to follow these instructions may cause lift engine to expand rapidly and may result in equipment damage and or personal injury b After you remove the stop screw C After worksurface is raised to it s highest release the hand brake and move level Install all equipment the worksurface up to highest level CAUTION Make sure you leave 20 508mm of slack in all equipment cables to allow the worksurface to raise up it s full 20 508mm Failure to allow enough slack in equipment cables may cause cables to get pulled equipment to fall off desk and may result in product damage and or personal injury a 11 0f 15 888 24 228 G 00 rev B 07 13 1 2 G Adjustment Step Important You will need to adjust this product after installation is complete Make sure all your equipment is properly installed on the product before attempting adjustments This product should move smoothly and easily through the full range of motion and stay where you set it If movements are too easy or difficult or if product does not stay in desired positions follow the adjustment instructions to create Minimize Lift Strength BEFORE Removing Mounted Equipment Shipping the Cart Storing the Cart Install Stop S
Download Pdf Manuals
Related Search