Accell UltraAV
Contents
1. ACCELL connecting you UitraAV HDMI Splitter and Distribution Amplifier READ ME FIRST SETUP INSTRUCTIONS Thank you for purchasing the Accell UltraAV HDMI Distribution Amplifier This product is designed to provide an exceptional performance and value Please review the manual before operating and retain for future reference CAUTION 1 Ensure the unit has sufficient ventilation Do not cover ventilation openings Do not install in a confined space 2 Do not operate near source of heat Do not stack on top underneath or between other heat generating unit s including other amplifiers 3 Unplug power adapter if not used for an extended period 4 To prevent damage from power Surges the unit should be plugged into a surge protector or surge pro tected power source 5 Do not use near liquid or areas of heavy moisture 6 Clean unit with a clean and dry cloth only 7 This unit cannot be serviced in the field Contact Accell if service is required 8 Do not open case risk of shock Shock hazard 9 Do not modify power cord or use the product if the power cord is damaged Introduction The UltraAV HDMI Distribution Amplifier Splitter accepts a signal from a single HDMI enabled audio video source and splits the single input into 4 1x4 Splitter or into 8 1x8 Splitter HDMI outputs The audio video signal is mirrored on up to 4 1x4 Splitter or 8 1x8 Splitter HDMI displays2. cable length as short as possible Test by locating the non working display close to the splitter Use a short HDMI cable to connect the splitter to the TV A working TV using a short HDMI cable indicates an issue with the HDMI cable Q Get the message This protocol is not supported or other error message A See answer A1 above and repeat the steps outlined Q The splitter is not down sampling the video and some of the TV s are not displaying a picture troubleshooting continued A1 Go into the TV s setup and configure the resolution to match all the connected TV s The TV s should share the same resolution A2 In the source devices menu options set the source device to output a resolution that matches all the connected displays Q My TV s resolution are not optimized A The splitter will query the displays and provide the highest common video resolution amongst them Example Using a 1080p source if 3 of the displays support a maximum resolution of 1080p and 1 display Supports a maximim resolution of 720p all 4 display will operate ata resolution of 720p If the 720p TV in the example is then turned off the other 3 displays can then operate in 1080p resolution Press the RESET button on the front panel of the splitter to refresh the configuration The three 1080p TV s will refresh flicker then each will display a 1080p resolution picture ASSISTANCE Questions regarding this product or its product warranty pl
3. ENT SHALL ACCELL CORPORATION ITS SUBSIDIARIES OR AFFILIATES OR THEIR RESPECTIVE PARTNERS OFFICERS DIRECTORS EMPLOYEES SHAREHOLDERS REPRESENTATIVES OR AGENTS COLLECTIVELY ACCELL BE LIABLE FOR DIRECT SPECIAL INCIDENTAL CONSEQUENTIAL PUNITIVE OR INDIRECT DAMAGES INCLUDING BUT NOT LIMITED TO LOSS OF DATA USE OR PROFITS HOWEVER CAUSED WHETHER FOR BREACH OF CONTRACT NEGLIGENCE OR OTHERWISE AND WHETHER OR NOT ACCELL HAS BEEN ADVISED OF THE POSSIBILITY OF ANY SUCH DAMAGES YOU AGREE THAT ACCELL S MAXIMUM LIABILITY ARISING FROM ANY PRODUCT SOLD BY ACCELL SHALL NOT EXCEED THE PRICE OF SUCH PRODUCT SOME JURISDICTIONS DO NOT ALLOW THE LIMITATION OF EXCLUSION OF LIABILITY FOR CERTAIN DAMAGES SO THE ABOVE MAY NOT APPLY TO YOU TO THE EXTENT SUCH JURISDICTION S LAW IS APPLICABLE TO THIS AGREEMENT WARRANTY RETURNS PROCEDURE Contact Customer Support to obtain a Return Authorization RMA number RMA numbers are valid for 30 days from the date of issuance We are unable to accept returns without an RMA number Returns without an RMA number clearly printed on the outside of the package will be refused and returned unopened All returns must be shipped prepaid at the expense of the shipper Accell assumes no responsibility for any inaccuracies and liability for direct indirect special incidental or consequential damages as a result Due to ongoing improvements Accell reserves the right to make changes to hardware packa
4. be used when using this device Turn off CEC or HDMI Link functionality in the source devices and displays The illustration below shows the optional Ultra IR Adapter Kit controlling the source device on a 1x4 splitter The 1x8 splitter is setup in a similiar manner Note Due to specific pin requirements only use Accell Ultra IR transmitters or receivers o HDMI Cable Displays a IR RX Remote Control Ultra IR Adapter Kit PN B164B 001B Includes IR Adapter 1 pc IR Transmitter 5 ft 1 pc Dual Frequency 38KHZ 60KHZ IR Receiver 5 ft 1 pc Ultra IR Receiver 5 ft Dual Frequency 38KHZ 60KHZ PN B164B 002B Ultra IR Transmitter 5 ft Dual Frequency 38KHZ 60KHZ PN B164B 003B Ultra IR Receiver and Transmitter Pin assignment Troubleshooting Q One of the display does not show a picture or output audio A Check the displays input setting to ensure it is set to receive a signal from the connected HDMI port Q One or more of the connected displays will not display a picture while one or more of the displays do display a picture A1 Press the RESET button on the front of the splitter to reset it Alternatively turn off the power to the splitter source and displays Wait 60 seconds Turn the source on Turn the displays on Turn the splitter on A2 The HDMI cables on the non functonal display s cannot support their long length Use only high quality High Speed HDMI cables Keep the
5. ease check out our Web site at www accellcables com Customer service can be reached by email at support accellcables com or phone at 510 438 9288 toll free 877 353 0772 M F 9am 5pm PST 1 YEAR MANUFACTURERS WARRANTY The Accell UltraAV Splitter is warranted for one year from date of purchase to be free of defects in material and workmanship In the event of such defects the Accell product will be repaired without charge or replaced with a new one at our option if delivered to Accell Corporation prepaid together with a copy of the sales receipt indicating the proof of purchase date and place of purchase This warranty excludes defects due to normal wear abuse shipping damage or failure to use the product in accordance with the instructions ACCELL CORPORATION SHALL NOT BE LIABLE FOR DAMAGES BASED UPON INCONVENIENCE LOSS OF USE OF THE PRODUCT LOSS OF TIME INTERRUPTED OPERATION OR COMMERCIAL LOSS OR ANY OTHER DAMAGES WHETHER INCIDENTAL CONSEQUENTIAL OR OTHERWISE YOU AGREE THAT ACCELL S MAXIMUM LIABILITY ARISING FROM ANY PRODUCT SOLD BY ACCELL SHALL NOT EXCEED THE PRICE OF SUCH PRODUCT SOME JURISDICTIONS DO NOT ALLOW THE LIMITATION OF EXCLUSION OF LIABILITY FOR CERTAIN DAMAGES SO THE ABOVE MAY NOT APPLY TO YOU TO THE EXTENT SUCH JURISDICTION S LAW IS APPLICABLE TO THIS AGREEMENT This warranty gives you specific legal rights and you may have other rights that vary from state to state LIMITATION OF LIABILITY IN NO EV
6. ging and any accompanying documentation without prior written notice 2013 Accell Corporation All Rights Reserved Accell and UltraAV are registered trademarks of Accell Corporation
7. monitors projectors or TV s Over Current and Over Voltage Protection The circuit boards are equipped with both over current and over voltage protection and will automatically power down if encountered The circuit boards will restore automatically once the excessive current or voltage has passed Package Contents e HDMI Distribution Amplifier Splitter e Power Adapter e Owner s Manual 1x4 HDMI Distribution Amplifier Splitter Model KO78C O06B Specifications e Connect 1 HDMI Source to up to 4 HDMI Displays e Supports HD resolutions up to 1080P and 3D e HDMI 1 4a HDCP 1 2 compliant e Input video signal 5v p p Input DDC signal 5v p p TTL e Data transfer speed of 6 75Gbps 225MHz e Audio formats supported DTS HD 7 1 Dolby True HD 7 1 e Deep color up to 36 bit e Maximum input cable length Up to 20m 24AWG e Maximum output cable length Up to 20m 24AWG e Supports cascade up to 3 units e Shelf or surface mountable e 5V DC UL Listed power adapter e Input AC 50Hz to 60Hz 100 240V e Approximate dimensions 10 9 W x 1 1 H x 6 1 D 277W x 28H x 156D mm Model Numbers KO78C 006B 1x4 KO78C 007B 1x8 specifications continued e Operating temperature range 5 to 131 F 15 to 55 C e Operating humidity range 5 to 90 RH no condensation 1x8 HDMI Distribution Amplifier Splitter Model KO78C 007B Specifications e Connect 1 HDMI Source to up to 8 HDMI Displays e Supports HD res
8. olutions up to 1080P and 3D e HDMI 1 4a HDCP 1 2 compliant e Input video signal 5v p p Input DDC signal 5v p p TTL e Data transfer speed of 6 75Gbps 225MHz e Audio formats supported DTS HD 7 1 Dolby True HD 7 1 e Deep color up to 36 bit e Maximum input cable length Up to 20m 24AWG e Maximum output cable length Up to 20m 24AWG e Supports cascade up to 6 units Silicon Image chipset e Rack shelf or surface mountable e 5V DC UL Listed power adapter e Input AC 50Hz to 60Hz 100 240V e Approximate dimensions 10 9 W x 1 1 H x 6 1 D 277W x 28H x 156D mm e Operating temperature range 5 to 131 F 15 to 55 C e Operating humidity range 5 to 90 RH no condensation Cascading The HDMI splitter can be cascaded layered to expand the number of supported displays K078C 006B 1x4 Splitter Supports up to 3 layers K078C 007B 1x8 Splitter Features a Silicon Image chipset supporting up to 6 layers To create a 2 layer cascade two same distribution amplifiers must be used Run an HDMI cable from an output on unit 1 to the input of unit 2 A 2 layer cascade of the 1x4 splitter will support up to 7 outputs A 2 layer 1x8 splitter cascade will support up to 15 outputs With the splitter power switch in the OFF position connect an HDMI High Speed cable from the HDMI Output on the audio video source to the HDMI Input 1 on the back of the splitter Tips Use the shortest length HDMI cables possible in each poin
9. t in the installation Use only High Quality and High Speed HDMI cables Next connect an HDMI cable to the HDMI Output Port 1 on the splitter and then connect the other end to an HDMI Input Port on the display device Similarly using HDMI cables connect the remaining HDMI Output Ports on the rear of the splitter to the HDMI Input ports of the other displays Connect the power adapter to the splitter Plug the power adapter into a Surge protected AC power outlet Turn ON the video source and turn ON the displays Turn the splitter s power switch to the ON position Infrared Control IR The area on the front panel labeled IR or IR Extender is the IR Transmitter IR TX port Using the Ultra IR Adapter Kit optional enables the control of the source device from the location of the display Plug the HDMI cable into the IR Adapter at the display end Next plug the IR Adapter s HDMI connector into the display The IR Adapter has a port that accepts an optional IR Receiver IR RX When the IR RX receives an IR signal from the source devices remote control it uses the HDMI cable s CEC line to send the signal to the splitter Plug the optional IR TX into the IR port on the front panel of the splitter Point the end of the IR TX at the source device The signal is transmitted through the IR TX sending the IR signal to the source device Note As the Ultra IR Adapter uses the CEC channel of the HDMI cable the CEC function cannot
Download Pdf Manuals
Related Search