Home

Samsung AQ09TSBN air conditioner

1. Boracay EUR_AQ09T amp U _IBIM_32447A_E indd 5 2011 3 19 10 07 27 Checking before use A Operation ranges The table below indicates the temperature and humidity ranges the air conditioner can be operated within Refer to the table for efficient use Mode Indoor temperature Outdoor temperature Indoor humidity Cooling 16 C 32 C 15 C 43 C Relative humidity 80 or less Dry 18 C 32 C 15 C 43 C z Heating 27 C or less 5 C 24 C gt If the air conditioner operates in cooling mode for long period of time in high humidity area dew may be formed gt If the outdoor temperature goes down to 5 C heating capacity may decrease as much as 60 70 of specified capacity according to the using conditions i Maintaining your air conditioner Internal protections via the unit control system gt This internal protection operates if an internal fault occurs in the air conditioner Type Description Against cold air The internal fan will be off to against cold air when the heat pump is heating De ice cycle The internal fan will be off to against cold air when the heat pump is heating Anti protection of internal battery Protect compressor The compressor will be off to protect internal battery when the air conditioner operates in Cool mode The air conditioner does not start operating immediately to protect the compressor of the outdoor unit after it has been starte
2. End of the wire must be circular HSNI XX24XXK Indoor unit Ground wire Green Yellow Outdoor unit Green Yellow caution After connecting the cables make sure terminal numbers on the indoor outdoor unit matches e Screws on terminal block must not be unscrewed with the torque less than 12kgf cm 10 Connect the grounding conductor to the grounding terminals 11 Close the terminal board cover by tightening the screw carefully In Russia and Europe consult with the supply authority to determine the supply system impedance before installation Connect the wires firmly so that wires can not be pulled out easily If they are loose it could cause burn out of the wires Connect the wires according to color codes referring to the wiring diagram The power cable and the interconnection cable should be selected according to the specification in page 28 Boracay EUR_AQO9T amp U _IBIM_32447A E indd 29 29 2011 3 19 10 08 13 Installing and connecting the assembly pipe of the indoor unit Connect indoor and outdoor units with field supplied copper pipes by means of flare connections Use insulated seamless refrigeration grade pipe only Cu DHP type according to 1SO1337 degreased and deoxidized suitable for operating pressures of at least 4200 kPa and for burst pressure of at least 20700 kPa Under no circumstances must sanitary type copper pipe be used There are 2 refrigerant pipe
3. lt Low pressure gt Liquid service port lt High pressure gt Y Model XX09XX XX 12XX XXK18XX XX24XKXK S AX Y HSNI Vacuum Pump Backward flowing prevention or liquid 10 20 20 25 The remaining air in the Refrigeration cycle which contains moisture may cause malfunction on the compressor caution Always contact the service center or a professional installation agency for product installation Boracay EUR_AQO9T amp U _IBIM_32447A_E indd 35 35 2011 3 19 10 08 20 SCL RSR a E Purging the connected pipes l Important information regulation regarding the refrigerant used This product contains fluorinated greenhouse gases covered by the Kyoto Refrigerant type GWP value Protocol Do not vent gases into the atmosphere R410A 1975 GWP Global Warming Potential 1 Please fill in with indelible ink gt the factory refrigerant charge of the product Contains fluorinated greenhouse gases gt the additional refrigerant amount charged in the field and AE Ee Soweto Indoor unit gt the total refrigerant charge on the refrigerant charge label supplied with the product a Factory refrigerant charge of the product NOTE See unit name plate d a b Additional refrigerant amount charged in the field Refer to the above information for the quantity of refrigerant Outdoor unit replenis
4. Be careful with the sharp edges on the outdoor unit heat exchanger i Opening the panel Tightly grab top of the front panel and pull it down to open Then slightly lift the panel up Boracay EUR_AQO9T amp U _IBIM_32447A E indd 17 PRISES RERO Re b gt SR PSS SSSR RSR X ESS RSR RKO K MOLL CKO KKH ROR KOC KS OK OKO ROKK KKK KCK ISL ROOD PSK RSS SRE SKORIK HOD SSSR CKO KK SLRS KOK oO SOKO SC lt lt se lt 2 SX LILLIES ERR KKK LISILO SISESE OISE CKO KK E509 SKK KK CKO K GOK SOCK KK 5050 ORK K OES KOSH SSK KO QS ne LES RS Heat exchanger Illustration may differ slightly depending on the models HSNI 2011 3 19 10 07 51 SCL RSR a Cleaning the air conditioner q Removing the Air filter Grab the handle and lift it up Then pull the Air filter towards you and slide it down Air filter Cleaning the air filter Washable foam based air filter captures large particles from the air The filter is cleaned with a vacuum or by hand washing Open the panel and put the Air filter out Clean the Air filter with a vacuum cleaner or soft brush If dust is too heavy rinse it with running water Insert the Air filter back in its original position Dry the Air filter in a ventilated area and close the front panel e Clean the Air filter every 2 weeks or when the filter clean reminder lights up Cleaning term may differ depending Note
5. Boracay EUR_AQO9T amp U _IBIM_32447A E indd 1 2011 3 19 10 07 24 On those hot sweltering summer days and long restless nights there is no better escape from the heat than the cool comforts of home Your new air conditioner brings an end to exhausting hot summer days and lets you rest Beat the heat with your own air conditioner this summer Hl Cost Efficient System Your new air conditioner not only provides maximum cooling power in the summer but also can be an efficient heating method in the winter with the advanced Heat pump system Heat pump system is 3 times more efficient compare to the other electrical heating appliance so you can further reduce its running cost Now meet year round needs with one air conditioner i Look for Everywhere The elegant and harmonious design gives priority to the esthetics of your space and complements any of your existing interior d cor With its soft color and rounded edge shape the new air conditioner adds class to any room Enjoy what your air conditioner offers both functionally and esthetically i good sleep function good sleep function allows you to set a comfortable sleep temperature while saving energy and having sound sleep Features of your new air conditioner Contents Cool Summer Offer USING PARTS Safety precautions sssmnnoneumenaemesasmnamsn 3 Checking before use rm 6 Checking the name of the Parts sseessssssss
6. Accessories in the indoor unit case Remote Batteries for User s amp Installation controller 1 Remote controller 2 Manual 1 Installation Plate 1 5 wire Assembly Cable 1 The flare nuts are attached to the end of each pipe of an evaporator or a service port Note Use the nuts when connecting the pipes e The 5 wire assembly cable is optional If it is not supplied use the standard cable e The drain plug and rubber leg are only included when the air conditioner is supplied without the assembly pipe as seen in the picture below 26 Boracay EUR_AQO9T amp U _IBIM_32447A_E indd 26 2011 3 19 10 08 04 CU RSR a E I Optional accessories The following connection accessories are optional If they are not supplied you should obtain them before installing the air conditioner Insulated Insulated Assembly Insulated Assembly Pipe Insulated Assembly Pipe Assembly Pipe Pipe 9 52mm 1 12 70mm 1 15 88mm 1 6 35mm 1 XX12 18X X XXK24KXK PET3 Foam Tube Insulation 1 Vinyl Tapes 2 Drain Plug 1 HSNI M4 x 25 Tapped Drain Hose Screws 6 length 2m 1 eg If these accessories are supplied they will be in the accessory box NOTE i Tools required for installation General Tools Vacuum Pump Backward flowing prevention e Manifold Gauge e Stud Finder e Torque Wrench e Pipe Cutter e Reamer e Pipe Bender e Spirit Level e Screw Driver Spanner e Drill e LWren
7. gas leaks on the indoor unit Check the flare nut C and D using a leak detector Leak test with nitrogen before opening valves In order to detect basic refrigerant leaks before recreating the vacuum and recirculating the R410A it s responsible of installer to pressurize the whole system with nitrogen using a cylinder with pressure reducer at a pressure above 40 bar gauge Leak test after opening valves Before opening valves discharge all the nitrogen from the system and create vacuum according to page 34 36 After opening valves check leaks using a leak detector for refrigerant Pump down before disconnecting the refrigerant connections for unit repair removal or disposal Pump down is an operation intended to collect all the system refrigerant in the outdoor unit This operation must be carried out before disconnecting the refrigerant tubing in order to avoid refrigerant loss to the atmosphere gt Shut off the liquid valve with the Allen wrench gt Turn the system on in cooling with fan operating at high velocity Compressor will immediately start provided 3 minutes have elapsed since the last stop gt After 2 minutes of operation shut the suction valve with the same wrench gt Turn the system off and switch mains supply off gt Disconnect tubing After disconnection protect valves and tubing ends from dust gt Compressor damage may occur if run at a negative suction pressure 37 Boracay EUR_AQ
8. hands or fingers during the heating operation gt This may result in electric shock or burns Do not insert your fingers or foreign substances into the air inlet outlet of the air conditioner gt Take special care that children do not injure themselves by inserting their fingers into the product Do not strike or pull the air conditioner with excessive force gt This may result in fire injury or problems with the product Boracay EUR_AQO9T amp U _IBIM_32447A E indd 4 2011 3 19 10 07 27 SCL HSE E FOR USING WARNING Do not place an object near the outdoor unit that allows children to climb onto the machine gt This may result in children seriously injuring themselves Do not use this air conditioner for long periods of time in badly ventilated locations or near infirm people gt Since this may be dangerous due to a lack of oxygen Open a window at least once an hour If any foreign substance such as water has entered the appliance cut the power by unplugging the power plug and turning the circuit breaker off and then contact your nearest service center gt Failing to do so may result in electric shock or fire HSNI Do not attempt to repair disassemble or modify the appliance yourself gt Do not use any fuse such as cooper steel wire etc other than the standard fuse gt Failing to do so may result in electric shock fire problems with the product or injury FOR USING CAUTION Do
9. is turned on X Auto Cleaning time can vary depending on the previously used mode Auto cool Cool Dry mode approximately 30 minutes Auto heat Heat Fan mode approximately 15 minutes Cancel Press the Auto Clean button once again e When the air conditioner is turned on the Auto clean function runs after NOTE stopping the air conditioner operation 16 Boracay EUR_AQO9T amp U _IBIM_32447A E indd 16 2011 3 19 10 07 49 Cleaning the air conditioner CAUTION Make sure the power is turned off and unplugged from the wall socket when cleaning the air conditioner i Cleaning the indoor unit gt Wipe the surface of the unit with a slightly wet or dry cloth when needed NOTE Contact the service center when you clean the indoor unit heat exchanger because it needs to be disassembled Do not clean the display using alkaline detergent caution Do not use sulfuric acid hydrochloric acid organic solvents such as thinner kerosene and acetone etc to clean the surface of the product or put any stickers on it They may damage the surface of the air conditioner fi Cleaning the outdoor unit heat exchanger gt When dust accumulates on the heat exchanger it may decrease cooling performance Therefore clean it regularly gt Spray water to clean the dust NOTE CAUTION e If itis difficult to clean the outdoor unit heat exchanger on your own contact service center
10. or plants from the air flow from the air conditioner for long periods of time gt This may result in harm to humans animals or plants This appliance is not intended for use by persons including children with reduced physical sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety Children should be supervised to ensure that they do not play with the appliance FOR CLEANING WARNING O Do not clean the appliance by spraying water directly ontoit Do not use benzene thinner or alcohol to clean the appliance gt This may result in discoloration deformation damage electric shock or fire Before cleaning or performing maintenance unplug the air conditioner from the wall socket and wait until the fan stops gt Failing to do so may result in electric shock or fire FOR CLEANING CAUTION Q 9 Take care when cleaning the surface of the heat exchanger of the outdoor unit since it has sharp edges gt To avoid cutting your fingers wear thick cotton gloves when cleaning it Do not clean the inside of the air conditioner by yourself gt For cleaning inside the appliance contact your nearest service center gt When cleaning the internal filter refer to the descriptions in the Cleaning the air conditioner section gt Failure to do may result in damage electric shock or fire
11. over this manual to the user for storage in a handy and safe NOTE Place Pump down procedure when removing the product 1 Turn on the air conditioner and select Cool mode to run the compressor for 3 minutes 2 Release the valve caps on High and Low pressure side 3 Use L wrench to close the valve on the high pressure side 4 Approximately 2 minutes after close the valve on the low pressure side 5 Stop operation of the air conditioner 6 Disconnect the pipes 39 Boracay EUR_AQO9T amp U _IBIM_32447A_E indd 39 2011 3 19 10 08 28 ae Y How to connect your extended power cables Items to prepare compressor and insulation tape should be prepared by an installation technician Crimping plier Connection sleeve mm Insulation tape Contraction tube mm MH 14 20x 7 0 HxOD Width 18mm 50x 8 0 LxOD 1 As shown in the figure peel off the shields from the rubber wire Unit mm of the power cable Power cable provided by us Peel off 20 mm of the wire shields of the tube installed already A After peeling off the tube wire you must insert a contraction tube CAUTION 2 Insert both sides of core wire of the power cable into the connection sleeve 3 Using acompressor compress the two points and flip it over and compress another two points in the same location The compression dimension should be 8 0 After compressing it pull both sides of the wire to make sure it is firm
12. remote controller Point the remote controller towards the remote controller receiver of the indoor unit When you properly press the button on the remote controller you will hear beep sound from the indoor unit and a transmit indicator A appears on the remote controller display i Remote controller buttons Remote controller display Power Turn on off the air conditioner Mode Set one of the 5 operating modes Smart Saver Less energy usage makes your space cool between the temperature range of 24 C 30 C see pages 10 11 for instructions part Auto Clean Turbo x Auto clean function Dry inside of the indoor Operate in auto fan speed to i init to der idotodor cool quickly Turbo Quiet Air swing gt Activate Deactivate air flow blade movement automatically up and down Has no this function ia DOCIERS Temp Temp Fana wv Increase Decrease the temperature by 1 C E Adjust how much air flows through the air rel conditioner with the 4 different fan speeds good sleep such as Auto Low Medium High Set the good sleep mode on ey On Timer mer CR i as the timer good sleep mode Set the On Timer on goo P SE a as Cancel the timer good sleep mode Time Up Time Down Adjust the time for timer good sleep mode B This button doesn t have any function AN Make sure that the water does not get to the remote controller CAUTION 8 Boracay EUR_AQ09T amp U _IB
13. technical support if the unit produces smoke if the power cable is hot or damaged or if the unit is very noisy gt Always remember to inspect the unit electric connections refrigerant tubes and protections regularly These operations should be performed by qualified personnel only The unit contains moving parts which should always be kept out of the reach of children Do not attempt to repair move alter or reinstall the unit If performed by unauthorized personnel these operations may cause electric shocks or fires Do not place containers with liquids or other objects on the unit All the materials used for the manufacture and packaging of the air conditioner are recyclable The packing material and exhaust batteries of the remote controller optional must be disposed of in accordance with current laws gt The air conditioner contains a refrigerant that has to be disposed of as special waste At the end of its life cycle the air conditioner must be disposed of in authorized centers or returned to the retailer so that it can be disposed of correctly and safely 22 Boracay EUR_AQO9T amp U _IBIM_32447A E indd 22 2011 3 19 10 07 54 SCL RSR E Installing the unit IMPORTANT When installing the unit always remember to connect first the refrigerant tubes then the electrical lines gt Always disassemble the electric lines before the refrigerant tubes Upon receipt inspect the product to verify that i
14. 4 36 The pipe will be insulated and fixed permanently into position after finishing the installation and the gas leak test Note referto page 37 for further details e Tighten the flare nut with torque wrench according to specified method caution __ the flare nut is over tightened the flare may break and cause refrigerant gas leakage DO NOT WALL UP THE PIPE CONNECTION All refrigerant pipe connection must be easy accessible and serviceable 30 Boracay EUR AQO09T amp U _IBIM_32447A E indd 30 2011 3 19 10 08 13 Purging the indoor unit The indoor unit is supplied with inert gas nitrogen Before installing the unit check if nitrogen gas flow out of indoor unit If this one isn t true DO NOT INSTALL THE UNIT since leakage could be inside the indoor unit 1 Unscrew the caps at the end of each pipe gt All inert gas exhausts from the indoor unit HSNI To prevent dirt or foreign substances from getting into the pipes during Note installation do NOT remove the caps completely until you are ready to connect the pipes The remaining air in the Refrigeration cycle which contains moisture caution May cause malfunction on the compressor Always contact the service center or a professional installation agency for product installation Cutting or extending the pipe A 5 meter pipe is supplied with the air conditioner optional NOT FOR ITALY The length of the pipe can be
15. Extended up to see table page 24 e Shorten up to see page 24 If you need a pipe longer than 5 meters caution YOU must extend the assembly cable e You must add refrigerant to the pipes otherwise the indoor unit may freeze 1 Make sure that you have all the required tools pipe cutter reamer flaring tool and pipe holder 2 Ifyou want to shorten the pipe cut it using a pipe cutter ensuring that the cut edge remains at 90 with the side of the pipe see below examples of correct and incorrect cut edges Pipe 90 cutter Pipe 3 To prevent a gas leak remove all burrs at the cut edge of the pipe using a reamer A Face the pipe down while removing the burrs to make sure that burrs do not get in to the pipe CAUTION 4 Puta flare nut slightly into the pipe and modify the flare Outer Diameter D Depth A Flaring Size B 66 35 mm 1 3mm 9 0mm 99 52 mm 1 8mm 13 0 mm 12 70 mm 2 0 mm 16 2 mm 915 88 mm 2 2 mm 19 3 mm 19 05 mm 2 2 mm 22 5 mm 22 23 mm 2 2mm 25 7 mm 31 Boracay EUR_AQ09T amp U _IBIM_32447A_E indd 31 2011 3 19 10 08 14 SCL RSR Cutting or extending the pipe 5 Check if you flared the pipe correctly see examples of incorrectly flared pipes below Correct Inclined Damaged Cracked Uneven Surface Thickness 6 Align the pipes to connect them easily Tighten the flare nuts first with your hands and then with a torque wrench app
16. IM_32447A_E indd 8 2011 3 19 10 07 34 Operation mode indicator Turbo indicator er Low battery indicator Quiet indicator MA 280 Has no this function Transmit indicator Smart Saver indicator Air swing indicator Fan speed indicator gl Auto Turbo On Timer indicator cH Low Off Timer indicator SH E Medun good sleepindicator ail High Battery changing time When the battery is exhausted 424 will be displayed in the remote controller display When the icon appears change the batteries The remote controller requires two 1 5V AAA type batteries Storing the remote controller When you do not use the remote controller for long time remove the batteries from the remote controller and store it Inserting the batteries 1 Push the lever as arrow 2 Insert two AAA batteries 3 Close the cover by place it back to its indicates on the rear side of the Check and match the and original position remote controller and pull up signs accordingly Make sure you You should hear click sound when the cover is have inserted the batteries in locked properly correct position The signal may not be received well of electronic lighting style fluorescent lamps such as inverter fluorescent lamps NOTE are in the same space e If other electrical products operate by the remote controller call your nearest contact center pzd Correct disposal of batteries in this product Appl
17. O9T amp U _IBIM_32447A_E indd 37 2011 3 19 10 08 21 SCL RSR Fixing the indoor unit in place Perform the following work on the area where gas leak test was done priorly After checking for gas leaks in the system insulate the pipe hose and cables Then place the indoor unit on the installation plate 1 To avoid condensation problems wrap foam insulation as shown in the figure on a part without insulation on the end of the pipes 2 Wind the pipe assembly cable and drain hose with vinyl tape 3 Place the bundle the pipe assembly cable and drain hose in the lower part Installation of the indoor unit carefully so it does not project from the rear of the indoor plate unit Vinyl tape 4 Hook the indoor unit to the installation plate and move the unit to the right and left until it is securely in place Make sure pipe does not move when you install the indoor unit on caution a installation plate 5 Wrap the rest of the pipe with vinyl tape 6 Attach the pipe to the wall using clamps optional Fixing the outdoor unit in place Install the outdoor unit in level on a stable base to avoid the generation of noise and vibration especially when installing the unit close to a neighbor If you install the outdoor unit in a place exposed to strong winds or at a height fix it to an appropriate support wall or ground 1 Place the outdoor unit as indicated on the top of the unit to let the disch
18. alve EEV 219 05 mm 990 1210 922 23 mm 990 1210 34 Boracay EUR_AQO9T amp U _IBIM_32447A_E indd 34 2011 3 19 10 08 20 3 Connect the charging hose of the low pressure side of manifold gauge toa gas service port as seen in the picture 4 Open the valve of the low pressure side of manifold gauge counterclockwise 5 Purge the air in the connected pipes using the vacuum pump for about 15 minutes gt Make sure that pressure gauge shows 0 1MPa 76cmHg after about 10 minutes This procedure is very important to avoid a gas leak gt Close the valve of the low pressure side of manifold gauge clockwise gt Turn off the vacuum pump gt Check for 2 minutes if there is any pressure change gt Remove the hose of the low pressure side of manifold gauge 6 Set a valve cork of liquid and gas service port to the open position 7 Mount the valve stem nuts and the service port cap to the valve and tighten them at the torque of 183kgf cm with a torque wrench 8 Check for a gas leak paying particular attention to the 3 way valve s stem nuts and to the service port cap Refer to page 37 A Adding Refrigerant Add refrigerant charge according to table below If you use a pipe longer than 5m Ag of refrigerant R410A must be added for each extra meter If you use a pipe shorter than 5m The purge time is normal Refer to the Service Manual for further details Manifold gauge Valve Gas service port
19. arged air out properly 2 Fix the outdoor unit in level to an appropriate support using anchor bolts 3 Ifthe outdoor unit is exposed to strong winds install shield plates around the outdoor unit so that the fan can operate correctly Secure the rubber leg to prevent the generation of noise and vibration NOTE Connecting wires Drain hose Insulation CT Rubber leg Model X Y X 09 12X 457 254 XX18XX 543 319 XX24KX 660 340 Designed to cut off residual vibration I Outdoor unit installed on the wall by rack PE EET N A Ensure the wall will be able to suspend the weight of rack and H outdoor unit e Install the rack close to the column as much as possible Install proper grommet in order to reduce noise and residual vibration transferred by outdoor unit towards wall v_ N not supplied with product Soft rubber designed to cut off vibration from rack to wall not supplied with product 38 Boracay EUR_AQO9T amp U _IBIM_32447A E indd 38 2011 3 19 10 08 22 Final Check and Trial Operation To complete the installation perform the following checks and tests to ensure that the air conditioner operates correctly D e Check the followings e Strength of the installation si
20. ble When you install the unit make first refrigerant connections and then electrical connections Connect the air conditioner to grounding system before performing the electrical connection If unit is uninstalled first disconnect electrical cables then refrigerant connections If the outdoor unit is more than 5 meters away from the indoor unit you must extend the cable The maximum length of the cable is 15 09 12 20 18 24 meters 1 Extend the assembly cable if necessary Do not connect two or more different cables to extend the length caution tmay cause fire 28 Boracay EUR_AQO9T amp U _IBIM_32447A E indd 28 2011 3 19 10 08 09 2 Open the front grille 3 Remove the screw securing the connector cover 4 Pass the assembly cable through the rear of the indoor unit and connect the assembly cable to terminals Refer to the picture below B e Each wire is labeled with the corresponding terminal number NOTE Pass the other end of the cable through the 65mm hole in the wall Close the connector cover by tightening the screw carefully Close the front grille Remove the terminal board cover on the side of the outdoor unit ON AD UW Connect the cables to the terminals as seen in the picture Each wire is labeled with the corresponding terminal number NOTE X 09 12 18 X Indoor unit a ae OOQ Ground wire Green Yellow Outdoor unit 4 Outdoor unit
21. ch e Measuring Tape Tools for test operations e Thermometer e Resistance Meter Electroscope Fixing the installation plate You can select the direction of the drain hose depending on where you want to install the indoor unit Therefore before fixing the installation plate to a wall or a window frame you must determine the position of the 65mm hole through which the cable pipe and hose pass to connect the indoor unit to the outdoor unit When facing the wall the pipe and cable can be connected from the e Right A 3K Direction of pipe eu i Underside_right C Ed e Rear_right or left D A B D Q D 0 1 Determine the position of the pipe and drain hose hole as seen in the picture and drill the hole with an inner diameter of 65mm so that it slants slightly downwards Unit mm Model A B C D A Make sure to drill only one X 09 12X X 27 120 68 27 hole after choosing the 18 24 34 140 68 34 direction of the pipe 27 Boracay EUR_AQO9T amp U _IBIM_32447A E indd 27 2011 3 19 10 08 09 Fixing the installation plate 2 Fix the indoor unit If you fix the indoor unit on a wall 1 Fix the installation plate to the wall giving attention to the weight of the indoor unit Ifyou mount the plate to a concrete wall using plastic anchors make sure that NOTE gaps between the wall and the plate created by projected anchor is less than 20
22. d Ifthe heat pump is operating in Heat mode De ice cycle is actuated to remove frost from an outdoor unit that may Note have deposited at low temperatures The internal fan is switched off automatically and restarted only after the de ice cycle is completed 6 Boracay EUR_AQO9T amp U _IBIM_32447A_E indd 6 2011 3 19 10 07 28 SCL RSR a E Checking the name of the parts Your air conditioner may slightly look different from illustration shown above depending on your model i Main parts M 09 12 18 24T M xx09 12 18 240X m a Ti I Room ROOMS temperature temperature NN sensor ee Air filter Air filter h Air intake under t ja pan o under the panel Air flow blade Air flow blade up and down up and down Air flow blade left and right Air flow blade Blade pin lever left and right Blade pin lever Display E 09 12 18 24T M 09 12 18 24U x good sleep indicator Timer Auto clean indicator EL o Operation indicator Operation indicator ald Timer Auto clean indicator A e a Smart Saver indicator Power l button Remote controller receiver D CL Power l button Boracay EUR_AQO9T amp U _IBIM_32447A E indd 7 2011 3 19 10 07 33 SCL RSR Checking the
23. does not come out of the air conditioner e Check if the set temperature is higher during Cool mode lower during Heat mode than the current temperature Press the Temp or button on the remote controller to change the set temperature e Check if the Air filter is blocked by dirt If there is a lot of dust on the Air filter cooling heating performance may decrease Clean them frequently e Check if the outdoor unit is covered or installed near the obstacle Take the cover off and take the obstacle away e Ifyou want to operate the air conditioner in the sunlight cover the outdoor unit using curtains or etc e Check if the air conditioner is operating in De ice mode When the ice formed in winter or the outdoor temperature is too low the air conditioner operates in De ice mode automatically In De ice mode indoor fan stops and cool air does not come out Ifthe doors or windows are open it may cause bad cooling heating performance Close the doors and windows e Check if the air conditioner has just been turned on after stopping cooling or heating operation In this case just a fan will run to protect the outdoor unit compressor e Check if the pipe length is too long When the pipe length exceeds maximum allowable pipe length cooling heating performance may decrease Air flow adjustment is not working Check if you have selected Auto Dry good sleep mode In these modes desired temperature is set to auto and
24. e it on gt Off timer indicator stops blinking and reserved time will be displayed for 3 seconds Then the air conditioner operates in good sleep Cool mode gt If you don t press Set button within 10 seconds after pressing the good sleep or Time Up or Time Down button the air conditioner will return to previous status Check Off timer indicator and T amp kKXUX indicator on the indoor unit Cancel Press the Cancel button once again ere You can set the desired temperature by 1 C in the range of 16 C 30 C A Fan speed will be adjusted automatically according to the good sleep J mode Air flow direction will be adjusted automatically according to the good sleep mode Temperature and fan speed changes in good sleep mode Fall asleep Eases you into sleep by dropping the temperature Sound sleep Relaxes your body and raises your temperature slightly Wake up from good sleep mode Allows you to wake up from comfortable intermittent air and it makes you feel refreshed Set Off timer in good sleep mode over 5 hours You fell disturbed sleep if the good sleep is set too short or long NoTE because the default is set to 8 hour operation Ifthe good sleep mode is set less than 4 hours the operation will stop at the same time If the good sleep mode is set over 5 hours it will run as Wake up stage from the last one hour before it stops Recommended set temperature is betwe
25. e read this manual thoroughly to ensure that you know how to safely and efficiently operate the extensive features and functions of your new appliance Because the following operating instructions cover various models the characteristics of your air conditioner may differ slightly from those described in this manual If you have any questions call your nearest contact center or find help and information online at www samsung com Important safety symbols and precautions HSITDNA A WARNING Hazards or unsafe practices that may result in severe personal injury or death A CAUTION Hazards or unsafe practices that may result in minor personal injury or property damage a Unplug the power plug from the a Follow directions maces S Do NOT attempt Q Do NOT disassemble Make sure the machine is grounded to prevent electric shock FOR INSTALLATION WARNING OQ Plug the power cord into a wall socket with the power specifications of the product or higher and use the socket for this appliance only In addition do not use an extension cord gt Sharing a wall socket with other appliances using a power strip or extending the power cord may result in electric shock or fire gt Do not use an electric transformer It may result in electric shock or fire gt Ifthe voltage frequency rated current condition is different it may cause fire The installation of this appliance must be performed by a qualified technicia
26. e to electric leakage Install your appliance on a level and hard floor that can support its weight gt Failing to do so may result in abnormal vibrations noise or problems with the product Install the draining hose properly so that water is drained correctly gt Failing to do so may result in water overflowing and property damage When installing the outdoor unit make sure to connect the draining hose so that draining is performed correctly gt The water generated during the heating operation by the outdoor unit may overflow and result in property damage In particular in winter if a block of ice falls it may result in injury death or property damage Boracay EUR_AQ09T amp U _IBIM_32447A_E indd 3 2011 3 19 10 07 26 Safety precautions FOR POWER SUPPLY WARNING a Remove all foreign substances such as dust or water from the power plug terminals and contact points using a dry cloth on a regular basis gt Unplug the power plug and clean it with a dry cloth gt Failing to do so may result in electric shock or fire Plug the power plug into the wall socket in the right direction so that the cord runs towards the floor gt Ifyou plug the power plug into the socket in the opposite direction the electric wires within the cable may be damaged and this may result in electric shock or fire When the appliance or power plug or power cord is damaged contact your nearest service center Plug the power plug
27. en 25 C 27 C for cooling and 21 C 23 C for heating 13 Boracay EUR_AQO9T amp U _IBIM_32447A E indd 14 2011 3 19 10 07 47 Setting the On Off timer You can set the air conditioner to turn on off automatically at desired time Setting On timer while the air conditioner is off Off timer while the air conditioner is on 1 Press the On Timer Off Timer button gt On Off timer indicator will blink on the remote controller display Setting On timer a Timer Up NS 2 Press the Time Up or Time Down button to set the time Off Time gt You can set the time in half hourly unit from 30 minutes 3 hours and hour unit from Timer 3 hours 24 hours gt Operating hour can be set from minimum 30 minutes to maximum 24 hours 3 Press the Set button to active it on gt On timer indicator stops blinking and reserved time will be displayed for 3 seconds gt If you don t press Set button within 10 seconds after selecting the time the air conditioner will return to previous status Check On timer or Off timer indicator and a indicator on the indoor unit Setting Off timer Cancel Press the Cancel button Additional options available in On timer mode You can select from Auto Cool Dry Fan Heat Fan You can adjust the fan speed in Cool Fan Heat mode SET C Lt You can adjust the temperature in Auto Cool Dry Heat mode Only the latest setting timer will be applied betwe
28. en the On Timer Off Timer Note and good sleep Off timer functions After setting the timer the set time will be displayed for 3 seconds before it disappears 14 Combining On Timer and Off Timer If the air conditioner is on If the air conditioner is off Preset time on On timer is longer than Off timer Preset time on On timer is shorter than Off timer Ex On timer 3 hours Off timer 1 hour Ex On timer 3 hours Off timer 5 hours The air conditioner will operate the Off timer after The air conditioner will operate On timer after 3 hours m 1 hour from the moment you have set the timer from the moment you have set the timer a Your air conditioner will turn on after 2 hours Your air conditioner will remain on for 2 hours and then a turn off automatically On timer and Off timer setting time should be different from each other NOTE Press the Cancel button on the remote controller while timer combination is on Both of the On and Off timer will be canceled and the indicator will disappear Using the Smart Saver function This function will set the temperature range limit to help you save energy while the air conditioner is operating in Cool mode Press the Smart Saver button on the remote controller while the air conditioner is operating in Cool mode gt Smart Saver indicator and air swing indicator appears automatically on the remote rf controller display Quiet The air flow blades mo
29. esseesssessseseeen 7 Checking the remote controller ssscssssseesssssssssessesesseeesee 8 Basic FUNCION Sa tere 10 Adjusting the air flow direction wesssssssssssssssesseessssseseseen 12 Using the Turbo function ns 12 good SUSE PO rennes 13 Setting the ON OFF timer nm 14 Using the Smart Saver function nn 15 Using the Auto Clean function nn 16 Cleaning the air conditioner nn 17 Maintaining the air conditioner sscsssesesssssssssseseessseeen 19 Troubleshooting sessvsssssiseissstnsletsarsasateivscranticnncsteasidescveiteaserssuse 20 INSTALLATION PARTS Safety precautions as sssivscivsvansvevvoveeneeioniernivecvsssernivensorannivecsiveiin 22 Choosing the installation location sssssssseesessessesssseeses 23 PIGCESSOUES ae anna 26 Fixing the installation plate sssscssssssssseessassssseseessuesee 27 Connecting the assembly cable nn 28 Installing and connecting the assembly pipe of the indoor unit sssssssesssssssecssssssscesnsssscessessssesesesees 30 Purging the indoor Unit sesssssonessisnemeinusas 31 Cutting or extending the pipe eesssssssssseccssssensssssssssssesseses 31 Installing and connecting the drain hose of the indoor unit sen 32 Changing direction of the drain hose ues 33 Installing and connecting the drain hose of the outdoor unit nn 34 Purging the connected pipes rs 34 Performing the gas leak tests ssssssssssssssessssssssesseeessses 37 FIXING the indoor unit in place nn 38 FIXING t
30. esult in an explosion or fire To reinstall the air conditioner please contact your nearest service center gt Failing to do so may result in problems with the product water leakage electric shock or fire gt A delivery service for the product is not provided If you reinstall the product in another location additional construction expenses and an installation fee will be charged gt Especially when you wish to install the product in an unusual location such as in an industrial area or near the seaside where it is exposed to the salt in the air please contact your nearest service center Do not touch the power plug or the circuit breaker with wet hands gt This may result in electric shock Do not unplug the power plug or turn the air conditioner off with the circuit breaker while it is operating gt Plugging the power plug into the wall outlet or turning the air conditioner on from the circuit breaker may cause a spark and result in electric shock or fire After unpacking the air conditioner keep all packaging materials well out of the reach of children as packaging materials can be dangerous to children gt Ifa child places a bag over its head it may result in suffocation Do not insert your fingers or foreign substances into the outlet when the air conditioner is operating gt Take special care that children do not injure themselves by inserting their fingers into the product Do not touch the air flow blade with your
31. he outdoor unit in place s sssssssssssssessssssssessssssesesesss 38 Final check and trial operation ssssscssessessseeessesssesseen 39 Pump down procedure when removing the product ns 39 How to connect your extended power cables 40 Correct Disposal of This Product Waste Electrical amp Electronic Equipment Applicable in the European Union and other European countries with separate collection systems This marking on the product accessories or literature indicates that the product and its electronic accessories e g charger headset USB cable should not be disposed of with other household waste at the end of their working life To prevent possible harm to the environment or human health from uncontrolled waste disposal please separate these items from other types of waste and recycle them responsibly to promote the sustainable reuse of material resources Household users should contact either the retailer where they purchased this product or their local government office for details of where and how they can take these items for environmentally safe recycling Business users should contact their supplier and check the terms and conditions of the purchase contract This product and its electronic accessories should not be mixed with other commercial wastes for disposal Boracay EUR_AQO9T amp U _IBIM_32447A_E indd 2 2011 3 19 10 07 26 SCL HSE Safety precautions Before using your new air conditioner pleas
32. hment c Total refrigerant charge d Refrigerant cylinder and manifold for charging Hl Charging the refrigerant under conditions of liquid by using a liquid pipe R410A is a mixed type of refrigerant It is necessary for recharging under conditions of liquid When recharging refrigerant from the refrigerant cylinder to the equipment follow the instructions below 1 Before recharging check whether the cylinder has a siphon or not There are two ways to recharge the refrigerant Cylinder with siphon Cylinder without siphon gt Charge the refrigerant standing the gt Charge the refrigerant turning the cylinder cylinder upright upside down e If R410A refrigerant is charged with gas the composition of the charged refrigerant changes and the characteristics of the equipment vary e During the measuring operation of refrigerant quantity added use an electronic balance If cylinder doesn t have syphon upset it 36 Boracay EUR_AQO9T amp U _IBIM_32447A_E indd 36 2011 3 19 10 08 21 SCL RSR a E Performing the gas leak tests Make sure to check for gas leaks before completing the installation process connecting the assembly pipe and hose between indoor unit and outdoor unit insulating the cables hose and pipe and fixing the indoor unit to the installation plate HSNI To check for gas leaks on the outdoor unit Check the valve A and B using a leak detector To check for
33. icable in the European Union and other European countries with separate battery return systems This marking on the battery manual or packaging indicates that the batteries in this product should not be disposed of with other household waste at the end of their working life Where marked the chemical symbols Hg Cd or Pb indicate that the battery contains mercury cadmium or lead above the reference levels in EC Directive 2006 66 If batteries are not properly disposed of these substances can cause harm to human health or the environment To protect natural resources and to promote material reuse please separate batteries from other types of waste and recycle them through your local free battery return system HSITDNA Boracay EUR_AQ09T amp U _IBIM_32447A_E indd 9 2011 3 19 10 07 26 CU RSR Basic function Basic operation is an operation mode that can be selected by pressing the Mode button I Auto In Auto mode the air conditioner will automatically set the temperature and fan speed depending on the room temperature detected by the room temperature Cool In Cool mode the air conditioner will cool your room You can adjust the temperature and the fan speed to feel cooler in hot season e If current outside temperatures are much higher than the selected indoor temperature it may take time to bring the inner temperature to the desired coolness Dry The air conditioner in Dry mode acts like a dehumidifier by
34. in warranty and charged to end user Power supply line fuse or circuit breaker gt Always make sure that the power supply is compliant with current safety standards Always install the air conditioner in compliance with current local safety standards Always verify that a suitable grounding connection is available Verify that the voltage and frequency of the power supply comply with the specifications and that the installed power is sufficient to ensure the operation of any other domestic appliance connected to the same electric lines Always verify that the cut off and protection switches are suitably dimensioned Verify that the air conditioner is connected to the power supply in accordance with the instructions provided in the wiring diagram included in the manual Always verify that electric connections cable entry section of leads protections are compliant with the electric specifications and with the instructions provided in the wiring scheme Always verify that all connections comply with the standards applicable to the installation of air conditioners Choosing the installation location i Indoor unit gt gt gt vv vV VvV V Boracay EUR_AQO9T amp U _IBIM_32447A_E indd 23 2011 3 19 10 07 55 Where airflow is not blocked Where cool air can be distributed throughout the room Install the refrigerant piping length and the height difference of both indoor and outdoor units as indicated in the installa
35. into the wall socket firmly Do not use a damaged power plug damaged power cord or loose wall socket gt This may result in electric shock or fire Do not pull the power cord when unplugging the power plug gt Unplug the power plug by holding the plug gt Failing to do so may result in electric shock or fire Do not pull or excessively bend the power cord Do not twist or tie the power cord Do not hook the power cord over a metal object place a heavy object on the power cord insert the power cord between objects or push the power cord into the space behind the appliance gt This may result in electric shock or fire FOR POWER SUPPLY CAUTION When not using the air conditioner for a long period of time or during a thunder lightning storm cut the power at the circuit breaker gt Failing to do so may result in electric shock or fire FOR USING WARNING WD 4 If the appliance is flooded please contact your nearest service center gt Failing to do so may result in electric shock or fire If the appliance generates a strange noise a burning smell or smoke unplug the power plug immediately and contact your nearest service center gt Failing to do so may result in electric shock or fire In the event of a gas leak such as propane gas LP gas etc ventilate immediately without touching the power plug Do not touch the appliance or power cord gt Do not use a ventilating fan gt A spark may r
36. ithin the range of 16 C 30 C Cool You can adjust the desired temperature by 1 C within the range of 16 C 30 C Dry You can adjust the desired temperature by 1 C within the range of 18 C 30 C Fan Temperature adjustment is not possible Heat You can adjust the desired temperature by 1 C within the range of 16 C 30 C Air flow can be adjusted manually see page 12 for instructions 11 Boracay EUR_AQO9T amp U _IBIM_32447A E indd 11 2011 3 19 10 07 39 SCL RSR E Adjusting the air flow direction Air flow can be directed to your desired position Vertical air flow Air flow blades move up and down Press the Air swing button on the remote controller gt Air swing indicator will be on and air flow blades move up and down continuously to circulate the air gt Press the Air swing button on the remote controller again to keep the air flow direction in a constant position l Horizontal air flow Make sure one of the blade pin lever that stick out of the air flow blades are not broken Move the blade pin lever left or right to keep the air flow direction in a constant position you prefer Be extremely careful with your fingers while adjusting the Horizontal air flow direction There is a potential risk of personal injury when the unit is mishandled Using the Turbo function Turbo function will be helpful to cool your ro
37. ly pressed 4 Wrap it with the insulation tape twice and position your Insulation tape contraction tube in the middle of the insulation tape p 5 Apply heat to the contraction tube to contract it 40mm _ tube tape Incase of extending the electric wire please DO NOT use a round shaped pressing socket 6 After tube contraction work is completed wrap it with the insulation tape to finish A Incomplete wire connections can cause electric shock or a fire 4 40 Boracay EUR_AQO9T amp U _IBIM_32447A_E indd 40 2011 3 19 10 08 25 TW aaa LUE Memo HSNI 41 Boracay EUR_AQO9T amp U _IBIM_32447A E indd 41 2011 3 19 10 08 25 QUESTIONS OR COMMENTS COUNTRY CALL ALBANIA 42 27 5755 OR VISIT US ONLINE AT 0810 SAMSUNG AUSTRIA 7267864 0 07 min www samsung com www samsung com be Dutch BELGIUM SES ee Re Co BOSNIA 05 133 1999 BULGARIA 07001 33 11 www samsung com CROATIA 062 SAMSUNG 062 726 7864 www samsung com CZECH 800 SAMSUNG 800 726786 www samsung com DENMARK 70 70 19 70 www samsung com FINLAND 030 6227 515 www samsung com FRANCE 01 48 63 00 00 www samsung com GERMANY 01805 SAMSUNG 726 7864 0 14 Min www samsung com IT and Mobile 80111 SAMSUNG 80111 7267864 from land line local charge from GREECE mobile 210 6897691Cameras Camcorders www samsung c
38. lying the following torque Flare nut Outer Diameter Torque kgfecm 06 35 mm 140 170 99 52 mm 250 280 see 12 70 mm 380 420 15 88 mm 440 480 219 05 mm 990 1210 Indoor outlet pipe Connecting pipe 622 23 mm 990 1210 e Excessive torque can be cause of gas leakage In case brazing the pipe the nitrogen gas must be blown into the NOTE pipe 50 Pa The joint must be accessible and serviceable 7 For further details on how to connect to the outdoor unit and purge the air refer to page 34 36 e Tighten the flare nut with torque wrench according to specified method caution __ the flare nut is over tightened the flare may break and cause refrigerant gas leakage Installing and connecting the drain hose of the indoor unit When installing the drain hose for the indoor unit check if condensation draining is adequate When passing the drain hose through the 65 mm hole drilled in the wall check the followings Wall Indoor unit 0 Drain hose The drain hose must NOT The end of the drain hose must NOT slant upwards be placed under water 0 0 0 5cm Hess Zl Ditch The drain hose must not Keep a clearance of at least Do not place the end of the be bent 5cm between the end of the drain hose in a hollow drain hose and the ground 32 Boracay EUR_AQO9T amp U _IBIM_32447A_E indd 32 2011 3 19 10 08 16 CU RSR a i Drain hose installation 1 If necessary connect the 2 meter extensio
39. mm If you fix the indoor unit on a window frame lt 20mm Wye If you fix the indoor unit on a gypsum board 1 Determine the positions of the wooden uprights to be 1 Use stud finder to find out locations of the studs attached to the window frame 2 Fix the plate hanger on two studs 2 Attach the wooden uprights to the window frame giving attention to the weight of the indoor unit 3 Attach the installation plate to the wooden upright using tapping screws Search for other spots if there are less than two studs or the distance between the studs are different from the caution plate hanger e Fix the installation plate without inclining to one side Make sure that a wall can withstand the weight of the product If you install the product in a place where it is not warning Strong enough to withstand the product weight the unit could fall and cause injury Connecting the assembly cable Cable specification Model Power cable Interconnection cable Type GL XX09 12X X 3G 1 0mm HO7RN F 5G 1 0mm HO7RN F 20A 2G 0 75mm HOSRN F 3G 1 5mm HO7RN F 3G 2 5mm HO7RN F 2G 0 75mm HOSRN F KK 18K 3G 1 5mm HO7RN F 25A KK 24K 3G 2 5mm HO7RN F Connect the power cable to the auxiliary circuit breaker If every pole fails to connect to NOTE the power supply it must be incorporated in a wire with a contact opening of gt 3mm I Connecting the ca
40. n drain hose to the drain hose 2 Ifyou use the extension drain hose insulate the inside of the extension drain hose with a shield 3 Fit the drain hose into 1 of 2 drain hose holes then fix the end of the drain hose m tightly with a clamp G B Ifyou do not use the other drain hose hole block it with a rubber stopper NOTE Drain hose hole 4 Pass the drain hose under the refrigerant pipe keeping the drain hose Shield tight 5 Pass the drain hose through the hole in the wall Check if it slants Drain h A Extension drain h downwards as seen in the picture ain FR PRCRENIRES The hose will be fixed permanently into position after finishing the installation and the gas leak test refer to page Note 3 38 for further details e Make sure the installed direction of the drain hose is correct caution Inadequate installation may cause condensate water leakage If the drain hose is routed inside the room insulate the hose so that dripping condensation does not damage the furniture or floors DO NOT WALL UP THE DRAIN HOSE CONNECTION Drain hose connection must be easy accessible and serviceable Changing direction of the drain hose Change the direction only when it is necessary 1 Detach the rubber cap with the plier Screw hole 2 Detach the drain hose by pulling it and turning to the left 3 Insert the drain hose by fixing it with the screw into the groove
41. n or service company gt Failing to do so may result in electric shock fire explosion problems with the product or injury Install a switch and circuit breaker dedicated to the air conditioner gt Failing to do so may result in electric shock or fire Fix the outdoor unit firmly so that the electric part of the outdoor unit is not exposed gt Failing to do so may result in electric shock or fire S Do not install this appliance near a heater inflammable material Do not install this appliance in a humid oily or dusty location in a location exposed to direct sunlight and water rain drops Do not install this appliance in a location where gas may leak gt This may result in electric shock or fire Never install the outdoor unit in a location such as on a high external wall where it could fall gt Ifthe outdoor unit falls it may result in injury death or property damage This appliance must be properly grounded Do not ground the appliance to a gas pipe plastic water pipe or telephone line gt Failure to do so may result in electric shock fire an explosion or other problems with the product gt Never plug the power cord into a socket that is not grounded correctly and make sure that it is in accordance with local and national codes FOR INSTALLATION CAUTION Q This appliance should be positioned in such a way that it is accessible to the power plug gt Failing to do so may result in electric shock or fire du
42. not place objects or devices under the indoor unit gt Water dripping from the indoor unit may result in fire or property damage Check that the installation frame of the outdoor unit is not broken at least once a year gt Failing to do so may result in injury death or property damage Max current is measured according to IEC standard for safety and current is measured according to ISO standard for energy efficiency Do not stand on top of the appliance or place objects such as laundry lighted candles lighted cigarettes dishes chemicals metal objects etc on the appliance gt This may result in electric shock fire problems with the product or injury Do not operate the appliance with wet hands gt This may result in electric shock Do not spray volatile material such as insecticide onto the surface of the appliance gt As well as being harmful to humans it may also result in electric shock fire or problems with the product Do not drink the water from the air conditioner gt The water may be harmful to humans Do not apply a strong impact to the remote controller and do not disassemble the remote controller Do not touch the pipes connected with the product gt This may result in burns or injury Do not use this air conditioner to preserve precision equipment food animals plants or cosmetics or for any other unusual purposes gt This may result in property damage Avoid directly exposing humans animals
43. nt Do not vent R410A into atmosphere it is a fluorinated greenhouse gas covered by Kyoto Protocol with a Global Warming Potential GWP 1975 You should purge the air in the indoor unit and in the pipe If air remains in the refrigerant pipes it affects the compressor It may cause reduction of cooling capacity and malfunction Refrigerant for air purging is not charged in the outdoor unit Use Vacuum Pump as seen in the picture e When installing make sure there is no leakage When recovering the refrigerant ground the compressor first before removing the connection pipe If the refrigerant pipe is not properly connected and the compressor works with the service valve open the pipe inhales the air and it makes the pressure inside of the refrigerant cycle abnormally high It may cause explosion and injury 1 Connect each assembly pipe to the appropriate valve on the outdoor unitand Outdoorunit amp Indoor unit tighten the flare nut Gas pipe side a 2 Tighten the flare nut first with your hands and then with a torque wrench c m a applying the following torque B Excessive torque can be cause of gas leakage Outer Diameter Torque kgf cm 66 35 mm 140 170 Make the electrical connection and leave the system into stand by 99 52 mm 250 280 mode Do not turn on the system 212 70 mm 380 420 This is necessary for better vacuum operation full OPEN position of 015 88 mm 440 480 Electronic Expansion V
44. ocking front and the air outlet is towards the wall and the air outlet is opposite the and the rear side of the outdoor unit wall g v PON 0 A hy A A SSSR R S 0 o 2000 or more 5 ARE 2 A U a O 2 When installing more than 1 outdoor unit Unit mm When the air outlet is towards the wall When 3 sides of the outdoor unit are blocked by the wall U U U g F ue Li fel ICI IE ts gt lt a p 4 D lt m lt t 300 or more 600 or more 6000rmore 600 or more 25 Boracay EUR_AQO9T amp U _IBIM_32447A_E indd 25 2011 3 19 10 08 00 SCL RSR a E Choosing the installation location ieee When the walls are blocking front and the rear side of the outdoor When the upper part of the outdoor unit and units the air outlet is opposite the wall es Fe 600 or ba ue ae or more 300 or more 500 or more or more ME When front and rear side of the outdoor unit is towards the wall EU LPel ol 1500 or 600 or Emi or ET or as or more more more more more 500 or more e Ifinstallation is done in inappropriate space unit may generate sound and cause bad effect on the product caution Installation must be done in level and in a place where vibration will not cause any effect Accessories The following accessories are supplied with the air conditioner B The number of each accessory is indicated in parentheses NOTE I
45. of the drain hose and the outlet of the drain pan 4 Attach the rubber cap with a screwdriver by turning it to the right until it fixes to the end of the groove 5 Check for leakage on both side of the drain outlet Pour the water in direction of arrow Direction of the drained water 33 Boracay EUR_AQO9T amp U _IBIM_32447A_E indd 33 2011 3 19 10 08 18 Installing and connecting the drain hose of the outdoor unit While heating ice may accumulate During the process of defrosting check if condensation draining is adequate For adequate draining do the following 1 Insert the drain plug into the drain hole on the underside of the outdoor unit To avoid drain plug from contacting the ground secure gap between the caution ground and the bottom surface of the outdoor unit Drain hole Drain plug 2 Connect a drain hose to the drain plug Bottom surface of outdoor m LULL Drain plug Drain hose 3 Ensure that condensation draining is adequate Snow proof hood e In areas with heavy snow fall piled snow could block the air intake caution TO avoid this incident install a frame that is higher than estimated snow fall In addition install a snow proof hood to avoid snow from piling on the outdoor unit Estimated fall Ground Purging the connected pipes The outdoor unit is loaded with sufficient R410A refrigera
46. om Televisions and Household Appliances From mobile and fixed 2106293100 HUNGARY 06 80 SAMSUNG 726 7864 www samsung com ITALIA 800 SAMSUNG 726 7864 www samsung com KOSOVO 381 0113216899 LUXEMBURG 261 03 710 www samsung com MACEDONIA 023 207 77 MONTENEGRO 020 405 888 NETHERLANDS Q900 SAMSUNG 0900 7267864 0 10 Min www samsung com NORWAY 815 56 480 www samsung com POLAND 0 801 ee Hah 2678 www samsung com PORTUGAL 80820 SAMSUNG 726 7864 www samsung com 08010 SAMSUNG 08010 726 7864 only from RUMANIA landline local network Romtelecom local tariff www samsung com 021 206 01 10 for landline and mobile normal tariff SERBIA 0700 Samsung 0700 726 7864 www samsung com SLOVAKIA O800 SAMSUNG 726 7864 www samsung com sk SPAIN 902 1 SAMSUNG 902 172 678 www samsung com SWEDEN 0771 726 7864 SAMSUNG www samsung com Switzerland 0848 SAMSUNG 7267864 CHF 0 08 min ca Ain ne U K 0330 SAMSUNG 7267864 www samsung com EIRE 0818 717100 www samsung com LITHUANIA 8 800 77777 www samsung com LATVIA 8000 7267 www samsung com ESTONIA 800 7267 www samsung com Boracay EUR_AQO9T amp U _IBIM_32447A_E indd 42 2011 3 19 10 08 25 AQO9T xXx Series AQ12T Series AQ18T Series AQ24T Series AQO9U Series AQ12U Series AQ18U Series AQ24U Series imagine the possibilities Thank you for purchasing this Samsung product To receive more complete service please register your product at www samsung com regi
47. om quickly and effectively Press the Turbo button on the remote controller during Cool mode gt Turbo indicator appears on the remote controller display and the air conditioner operates in Turbo function for 30 minutes Cancel Press the Turbo button once again e Turbo function is only available in Cool mode NOTE e If you press the Mode button while the Turbo function is on it will cancel the function e Temperature Fan speed cannot be adjusted while using this function 12 Boracay EUR_AQO9T amp U _IBIM_32447A E indd 12 2011 3 19 10 07 42 Boracay EUR_AQO9T amp U _IBIM_32447A_E indd 13 2011 3 19 10 07 45 good sleepmode For a comfortable sleep the air conditioner will operate it Fall asleep gt Sound sleep gt Wake up from good sleep mode Temp good slee On Time i Up JE Off Time When the air conditioner is on and in cool heat mode 1 Press the good sleep button on the remote controller HSNI gt good sleep indicator appears and Off timer indicator starts blinking on the remote controller display 2 Press the Time Up or Time Down button to set the time gt You can set the time in half hourly unit from 30 minutes 3 hours and hour unit from 3 hours 12 hours gt Operating hour can be set from minimum 30 minutes to maximum 12 hours gt Default operation hour is set to 8 hours 3 Press the Set button to activ
48. onthe usage and environmental conditions In dusty area clean it once a week e If you turn off the air conditioner by pressing Power button the filter clean reminder will be turned off e Ifthe Air filter dries in a confined or humid area odors may generate If it occurs re clean and dry it ina well ventilated area 18 Boracay EUR_AQO9T amp U _IBIM_32447A_E indd 18 2011 3 19 10 07 58 SCL RSR a Maintaining the air conditioner If the air conditioner will not be used for an extended period of time dry the air conditioner to maintain it in best condition 1 Dry the air conditioner thoroughly by operating in Fan mode for 3 to 4 hours and disconnect the power plug There may be internal damage if moisture is left in components HSNI 2 Before using the air conditioner again dry the inner components of the air conditioner again by running in Fan mode for 3 to 4 hours This helps remove odors which may have generated from dampness l Periodical checks Refer to the following chart to maintain the air conditioner properly so Every 2 Every 3 Every 4 Type Description Le Rose Once a year Clean the air filter 1 Clean the condensate drain pan 2 Indoor unit Thoroughly clean the heat exchanger 2 a Clean the condensate drain pipe 2 Replace the remote controller batteries 1 Clean the heat exchanger on the outside of the unit 2 Oe Clean the heat exchanger on
49. re below when installing the air conditioner 300mm or more 125mm or more Wrap the refrigerant pipes and the drain hose with the absorbent pad and vinyl tape Refer to page 38 for further details draining left or right L m as maximum pipe length and 3 m as minimum pipe length CAUTION It will reduce noise and vibration H meters maximum total L meters maximum pipe length 600mm total pipe length minimum 300mm minimum SS 600mm minimum Model L H 09 12 18K 15 7 XXK24XX 20 8 Make at least one round It will reduce noise and vibration rance of the unit may be different from the diagram depending on the model The appea 24 Boracay EUR_AQO9T amp U _IBIM_32447A E indd 24 2011 3 19 10 07 58 q Space Requirements for Outdoor Unit When installing 1 outdoor unit Figure Description gt O Top view Side view A 7 Air intake Air outlet 4 Air intake Air outlet Yv 4 Air flow direction Unit mm When the air outlet is opposite the When the air outlet is towards the When 3 sides of the outdoor unit are wall wall blocked by the wall v w IAI LT ILL ER ER 5 U 2 gt E A AT Gis 8 oe a y T T A A 150 or more 600 or more The upper part of the outdoor unit The upper part of the outdoor unit When the walls are bl
50. removing moisture from the indoor air Dry mode makes the air feel refreshing in a humid climate Fan Fan mode can be selected to ventilate your room Fan mode will be helpful to refresh the stale air in your room l Heat The air conditioner heats as well as cools Warm your room with this versatile appliance in the cold of winter e Fan may not operate for about 3 5 minutes at the beginning to prevent any cold blasts while the air conditioner is warming up e Since the air conditioner heats the room by taking heat energy from outdoor air the heating capacity may decrease when outdoor temperature is extremely low Use an additional heating appliance in combination with the air conditioner if you feel the air conditioner heats insufficiently 10 Boracay EUR_AQO9T amp U _IBIM_32447A_E indd 10 2011 3 19 10 07 37 Press the button to turn on the air conditioner Press the button to set the operating mode Each time you press the Mode button the mode will change in order of Auto Cool Dry Fan and Heat HSNI Press the button to set the desired fan speed Auto cS a Auto Cool SH af Auto Low Sag Med Sag High Dry sa af Auto Fan SH Low Sag Med gl High Heat SH af Auto Low Sigg Med Sag High Press the y button to adjust the temperature Auto You can adjust the desired temperature by 1 C w
51. s normal Smoke is generated from f may not be a fire but it can be a steam generated by the defrost operation from outdoor the outdoor unit heat exchanger during Heat mode in winter Water is dropping from e Water may be generated because of the temperature difference It is normal the outdoor unit piping connection 21 Boracay EUR_AQO9T amp U _IBIM_32447A E indd 21 2011 3 19 10 07 54 W o lt INSTALLATION PARTS X In this manual you may find model names written in simplified forms as indicated in following table Model Names Included Models Remark AQ T AQO9T AQ12T AQ18T AQ24T Grouping was done by series AQk U AQOOUX X AQ12U AQ18U AQ24U XX09XX AQO9T AQOIUXX XX 129K AQ12T AQT2UX Grouping was done by capacity KK 189K AQ18T AQI8U KK 249K AQ24T AQ24U Safety precautions Carefully follow the precautions listed below because they are essential to guarantee the safety of the equipment e Always disconnect the air conditioner from the power supply before servicing it or accessing its internal components e Verify that installation and testing operations are performed by qualified personnel e Verify that the air conditioner is not installed in an easily accessible area General information gt Carefully read the content of this manual before installing the air conditioner and store the manual in a safe place in order to be able to use i
52. s of different diameters e The smaller one is for the liquid refrigerant e The larger one is for the gas refrigerant A short pipe is already fitted to the air conditioner You may need to extend the pipe using the assembly pipe optional The connection procedure for the refrigerant pipe varies according to the exit position of the pipe when facing the wall Right A L Left B ce Underside C C Rear 1 Cut out the appropriate knock out piece A B C on the rear of the indoor Outer Dane Torque kgfecm unit unless you connect the pipe directly from the rear 66 35 mm 140 170 2 Smooth the cut edges 99 52 mm 250 280 12 70 mm 380 420 3 Remove the protection caps of the pipes and connect the assembly pipe 15 88 mm 440 480 to each pipe Tighten the nuts first with your hands and then with a 219 05 mm 990 1210 torque wrench applying the following torque 022 23 mm 990 1210 amp e If you want to shorten or extend the pipes refer to page 31 32 NOTE 4 Cut off the remaining foam insulation 5 If necessary bend the pipe to fit along the bottom of the indoor unit Then pull it out through the appropriate hole gt The pipe should not project from the rear of the indoor unit gt The bending radius should be 100 mm or more 6 Pass the pipe through the hole in the wall 7 For further details on how to connect to the outdoor unit and purge the air refer to page 3
53. ster OOOOPOO 60 fd C 69 DB98 32447A 1 en Boracay EUR AQ09T amp U _IBIM_32447A E indd 43 2011 3 19 10 08 26
54. t as reference after installation gt For maximum safety installers should always carefully read the following warnings Store the operation and installation manual in a safe location and remember to hand it over to the new owner if the air conditioner is sold or transferred gt This manual explains how to install an indoor unit with a split system with two SAMSUNG units The use of other types of units with different control systems may damage the units and invalidate the warranty The manufacturer shall not be responsible for damages arising from the use of non compliant units gt The air conditioner is compliant with the requirements of the Low Voltage Directive 72 23 EEC the EMC Directive 89 336 EEC and the Directive on pressurized equipment 97 23 EEC gt The manufacturer shall not be responsible for damage originating from unauthorized changes or the improper connection of electric and requirements set forth in the Operating limits table included in the manual shall immediately invalidate the warranty gt The air conditioner should be used only for the applications for which it has been designed the indoor unit is not suitable to be installed in areas used for laundry gt Donotuse the units if damaged If problems occur switch the unit off and disconnect it from the power supply In order to prevent electric shocks fires or injuries always stop the unit disable the protection switch and contact SAMSUNG
55. t has not been damaged during transport If the product appears damaged DO NOT INSTALL it and immediately report the damage to the carrier or retailer if the installer or the authorized technician has collected the material from the retailer HSNI After completing the installation always carry out a functional test and provide the instructions on how to operate the air conditioner to the user Do not use the air conditioner in environments with hazardous substances or close to equipment that release free flames to avoid the occurrence of fires explosions or injuries To prevent injury when accidentally touching the indoor unit fan install the indoor unit at least 2 5m above the floor The air conditioner should be used only for the applications for which it has been designed the indoor unit is not suitable to be installed in areas used for laundry Our units must be installed in compliance with the spaces indicated in the installation manual to ensure either accessibility from both sides or ability to perform routine maintenance and repairs The unitscomponents must be accessible and that can be disassembled in conditions of complete safety either for people or things For this reason where it is not observed as indicated into the Installation Manual the cost necessary to reach and repair the unit in safety as required by current regulations in force with slings trucks scaffolding or any other means of elevation won t be considered
56. te Gf D Temp Fan e Tightness of pipe connection to detect gas leak fe v e Electric wiring connection e Heat resistant insulation of the pipe Drainage e Grounding conductor connection e Correct operation follow the steps below HSNI L D ner DE o aram 1 Press the Power button and check the following gt The indicator on the indoor unit lights up gt The airflow blade opens and the fan gears up for operation 2 Press the Mode button to select Cool or Heat mode gt In Cool mode use Temp or button and set the temperature at 16 C gt In Heat mode use Temp or button and set the temperature at 30 C Approximately 3 5 minutes later outdoor unit will start to operate and the Cool or Warm air will blow out NOTE After 12 minutes of stationary condition check the indoor unit air treatment Cooling mode indoor unit check Inlet air temp Outlet air temp From 10 K to 12 K indicative delta T Heating mode indoor unit check gt Outlet air temp Inlet air temp From 11 K to 14 K indicative delta T In heating mode the indoor fan motor can remain off to avoid cold air blown into conditioned space 3 Press the Air swing button and check the following gt The airflow blades work properly 4 Press the Power button to stop the operation e When you complete the installation successfully hand
57. the inside ofthe unit 2 Clean the electric components with jets of air 2 Outdoor Verify that all the electric components are firmly e unit tightened 2 Clean the fan 2 Verify that all the fan assembly is firmly tightened 2 Clean the condensate drain pan 2 This check mark requires checking the indoor outdoor unit periodically following to the description to maintain the air conditioner properly 1 The described operations should be performed more frequently if the area of installation is very dusty NOTE 2 These operations must always be performed by qualified personnel For more detailed information see the installation part in the manual 19 Boracay EUR_AQO9T amp U _IBIM_32447A_E indd 19 2011 3 19 10 07 54 BBC M LUE Troubleshooting Refer to the following chart if the air conditioner operates abnormally This may save time and unnecessary expenses PROBLEM SOLUTION The air conditioner does not work at all The temperature adjustment is not working e Check power status and then operate the air conditioner again Plugin or switch on the circuit breaker and then operate the air conditioner again e Check if you have set the Off Timer Operate the air conditioner again by pressing the Power button e Check if you have selected Fan Turbo mode In these modes desired temperature is set to auto and you cannot adjust the temperature Cool Warm air
58. tion diagram Wall that prevents vibration and is strong enough to hold the product weight Out of the direct sunlight 1m or more away from the TV or radio to prevent the screen from being distorted or noise from being generated As far away as possible from the fluorescent and incandescent lights so that the remote controller can be operated well A place where the air filter can be replaced easily 23 SCL RSR E Choosing the installation location Outdoor Unit Where it is not exposed to strong wind Well ventilated and dustless places Out of the direct sunlight and rain Where neighbors are not annoyed by operation sound or hot air Solid wall or support that prevents vibration and is strong enough to hold the product weight Where there is no risk of flammable gas leakage When installing the unit at a high place be sure to fix the unit legs 3m or more away from the TV or radio to prevent the screen from being distorted or noise from being generated Install the unit horizontally Place where drained water does not become any problem Place with no plants especially climbing plants and where small animal can not access vY YV YV vV V V V V V V AN e Avoid the following places to prevent malfunction of the unit caution Where there is machine oil Salty environment such as seaside areas Where sulfide gas exists Other special atmosphere areas Observe the clearances and maximum lengths as seen in the pictu
59. ve up and down gt Ifthe current set temperature is lower than 24 C it will automatically raise to 24 C Cancel Press the Smart Saver button once again SET C 1 Lt ul Smart Saver function is only available in Cool mode When Smart Saver function is activated temperature range will be limited to 24 C 30 C If the desired temperature is lower than 24 C turn off the Smart Saver function by pressing the Smart Saver button again Temperature Fan speed can also be adjusted see page 11 for instructions Air flow can be adjusted manually see page 12 for instructions If you press the Mode button while the Smart Saver function is on it will cancel the function 15 Boracay EUR_AQO9T amp U _IBIM_32447A_E indd 15 2011 3 19 10 07 48 Using the Auto Clean function Auto clean function will prevent from growing mold by eliminating the moisture inside of the indoor unit Your indoor unit evaporates the moisture inside of the unit Activate this function to provide you with more clean and healthier air Press the Auto Clean button When the air conditioner is turned off gt The Auto clean indicator on the indoor unit display appears and the Auto cleaning Q CR function runs KK09 12 18 24TXK K gt After stopping the air conditioner operation the Auto clean indicator on the indoor unit display appears and the Auto cleaning function runs When the air conditioner
60. you cannot adjust the temperature Fan speed adjustment is not working Check if you have selected Auto Dry Turbo good sleep mode In these mode fan speed is set to Auto and you cannot adjust the fan speed Remote controller is not working e Check if your batteries are depleted Make sure nothing is blocking your remote controller sensor e Check that there are strong lighting apparatus near the air conditioner Strong light which comes from fluorescent bulbs or neon signs may interrupt the electric waves Timer function does not set e Check if you press the Set button on the remote controller after you have set the time The indicator is blinking continuously Press the Power button or disconnect the power plug switch off the auxiliary power switch If the indicator is still blinking contact the service center Odors permeate in the room during operation e Check if the appliance is running in a smoky area Ventilate the room or operate the air conditioner in Fan mode for 1 2 hours We do not use smelly components in the air conditioner 20 Boracay EUR_AQO9T amp U _IBIM_32447A_E indd 20 2011 3 19 10 07 54 PROBLEM SOLUTION Error is indicated When an indoor unit indicator blinks contact the nearest service center m Q Noise is generated e Depending on the status of the air conditioner usage noise can be heard when refrigerant Z flow movement changes It i

Samsung AQ09TSBN air conditioner

Contents

Download Pdf Manuals

Related Search

Related Contents