LG F12B8QDA5 washing machine
Contents
1. 3 Press and hold the Temp button for three seconds while holding the phone mouthpiece to the icon or Power button 4 Keep the phone in place until the tone transmission has finished This takes about 17 seconds and the display will count down the time e For best results do not move the phone while the tones are being transmitted e If the call center agent is not able to get an accurate recording of the data you may be asked to try again e Pressing the Power button during the transmission will shut off the SmartDiagnosis 5 Once the countdown is over and the tones have stopped resume your conversation with the call center agent who will then be able to assist you using the information transmitted for analysis at the call to Customer information center e Smart Diagnosis is a troubleshooting feature designed to assist not replace the traditional method of troubleshooting through service calls The effectiveness of this feature depends upon various factors including but not limited to the reception of the cellular phone being used for transmission any external noise that may be present during the transmission and the acoustics of the room where the machine is located Accordingly LG does not guarantee that Smart Diagnosis would accurately troubleshoot any given issue 30 Baers of Warranty Disposal of your old appliance 1 When this crossed out wheeled bin symbol is attached to a product it mean2. LG Life s Good OWNER S MANUAL WASHING MACHINE Please read this manual carefully before operating your washing machine and retain it for future reference F14B8Q TD W A 1 9 F12B8Q TD W A 1 9 F10B8Q TD W A 1 9 P No MFL67463272 ver 21022013 00 www lg com P u Features E Protection against creases With the alternate rotation of the drum creasing in the laundry is minimized E Built in heater Internal heater automatically heats the water to the best temperature on selected cycles E More economical by Intelligent Wash System Intelligent Wash System detects the amount of load and water temperature and then determines the optimum water level and washing time to minimize energy and water consumption E Child Lock The child lock system is to be used for preventing children from pressing any button to change the program during operation E Low noise speed control system By sensing the amount of load and balance it evenly distributes load to minimize the spinning noise level E Direct Drive System The advanced Brushless DC motor rotates the drum directly without belt and pulley E 6 motion Washer is able to perform various drum actions or a combination of G different actions depending on the wash program selected Combined with a controlled spin speed and the ability of the drum to rotate both left and right the wash performance of the machine is greatly improved giving yo
3. X You can obtain the rubber cups p no 4620ER4002B from the LG spares dept Important Proper placement and levelling of the washer ensure long regular and reliable operation The washer must be absolutely horizontal and stand firmly in position It must not Seesaw across corners under load The installation surface must be clean free from floor wax and other lubricant coatings Do not let the feet of the washer get wet If feet of the washer get wet slipping may occur 10 C ii before washing E Before the first washing Select a cycle COTTON 60 C add a half load of detergent allow the unit to wash without clothing This will remove residues and water from the drum that may have been left during manufacturing E Caring before washing 1 Care Labels Look for a care label on your clothes This will tell you about the fabric content of your garment and how it should be washed 2 Sorting To get the best results Sort clothes into loads that can be washed with the same wash cycle Water temperature and spin speed and different fabrics need to be washed in different ways Always sort dark colors from pale colors and whites Wash separately as dye and lint transfer can occur causing discoloration of white etc If possible do not wash heavily soiled items with lightly soiled one Soil Heavy Normal Light eeeeeeeeeeee Separate clothes according to amount of soil Color White Lights Darks 6er S
4. especially if there is no floor drain gully in the immediate vicinity When disposing of the appliance cut off the mains cable and destroy the plug Disable the door lock to prevent young children being trapped inside Packaging material e g Films Styrofoam can be dangerous for children There is a risk of suffocation Keep all packaging well away from children E Installation of drain hose e When installing the drain hose sink secure it tightly with a string e Proper securing of the drain hose will protect the floor from damage due to water leakage Laundry tub Dp En lt Q The drain hose should not be placed higher than 100 cm above the floor Water in the washer does not drain or drains slowly Proper securing of the drain hose will protect the floor from damage due to water leakage e When the drain hose is too long do not force back into the washer This will cause abnormal noise Be oeiation E Level adjustment 1 Adjusting the washing machine level properly prevents excessive noise and vibration Install the appliance on a solid and level floor surface preferably in a corner of the room Timber or suspended type flooring may contribute to excessive vibration and unblance errors 2 If the floor is uneven adjust the adjustable feet as required do not insert pieces of wood etc under the feet Make sure that all four feet are stable and resting on the f
5. C sofa covers with light filling Coolmax Gore tex fleece Sports Wear and Sympatex Crease Care Intensive Machine washable woolens with pure new wool only A 60 C Intensive 60 Cotton and mix fabrics Cold to 60 C Delicate easily damaged laundry 20 C Colored laundry which is Cold to 40 C lightly soiled fast 6 0kg 4 0kg 4 0kg 2 0kg 4 0kg 3 0kg 2 0kg unction Water Temperature Select the water temperature to the wash cycles Always follow garment manufacture s care label or instructions when laundering Intensive When washing heavily soiled laundry you can increase effectiveness by choosing Intensive option Pre Wash If the laundry is heavily soiled Pre Wash Course is recommended Crease Care If you want to prevent crease select Crease Care button Medic Rinse For high effectiveness or more purity in rinse operation you can choose Medic Rinse option Set program at Cotton Eco 40 C Intensive Half Load Cotton Eco 60 C Intensive Half Load Cotton Eco 60 C Intensive Full Load option for test in accordance in conformity with EN60456 and Directive 1015 2010 Standard 60 C cotton program Cotton Eco 60 C Intensive Standard 40 C cotton program Cotton Eco 40 C Intensive They are the most efficient programmes in terms of combined energy and water consumptions for washing that type of cotton laundry Actual water
6. bra wires buttons etc e Replace fuses in or correct house wiring or correct house plumbing e Correction of unauthorized repairs e Incidental or consequential damage to personal property caused by possible defects with this appliance If this product is used for commercial purpose it is not warranted Example Public places such as public bathroom lodging house training center dormitory If the product is installed outside the normal service area any cost of transportation involved in the repair of the product or the replacement of a defective part shall be borne by the owner LG Life s Good CUSTOMER SERVICES Tel 44 0 844 847 LGLG 5454 Fax 44 0 844 847 1413 LGEUK SERVICE WEB SITE _ http Awww lge co uk For U K Customer
7. according to the program The required temperature lamp will light up for identification For the more detailed information please refer to the pagel4 Time Delay mn Time Delay mn Time Delay ERE lt ERE lt Preparing washing before starting Time Delay Turn on the water tap Load laundry and close the door Place the detergent and fabric softener in the drawer e How to set Time Delay Press Power button Turn the Program dial to select the program you require Press Time Delay button and set the desired time Press the Start Pause button blinks lf Time Delay button is pressed 3 00 is displayed The maximum delayed time is 19 hours and the minimum time is 3 hours e Each pressing of the button advances on time delay by one hour e To cancel the time delay press the Power button e Time Delay is expected time from the present to the completion of washing cycle or selected process Wash Rinse Spin e According to the condition of water supply and temperature the delayed time and the actual washing time may vary Hie to use washer Display 3 Completion of washing 1 A al bal kal bss op IDD aaa Wich Rinse Sole e When washing cycle is completed E mr is displayed on the Multi display 1 Special function display 4 Time left When child lock is selected the e During washing cycle the remaining washing
8. detergent UU B LL 2 Adding Fabric Softener Do not exceed the maximum fill line Close the dispenser drawer slowly SOFTENER Overfilling can cause early dispensing MAX of the fabric softener which could stain clothes Do not leave the fabric softener in the detergent drawer for more than 2 days Fabric softener could harden e Softener will automatically be added during the last rinse cycle Do not open the drawer when water is Supplied e Solvents benzene etc are not allowable KAB Do not pour fabric softener directly on the cloths a 12 padding detergent 3 Detergent dosage e Detergent should be used according to the instruction of the detergent manufacture e f too much detergent is used too many suds can occur and this will decrease the washing result or cause heavy load to the motor e It is recommended that you use powdered detergent for best results e If you wish to use liquid detergent follow guidelines provided by the detergent manufacturer e You can pour liquid detergent directly into the main detergent drawer if you are starting the cycle immediately e Please do not use liquid detergent if you are using time delay as the liquid may harden or if you have selected PRE wash e f too many suds occur please reduce the detergent amount e Detergent usage may need to be adjusted for water temperature water hardness size and soil level of the load For be
9. temperature may differ from the declared cycle temperature The test results depend on water pressure water hardness water inlet temperature room temperature type and amount of load degree of soiling utilized detergent fluctuations in the main electricity supply and chosen additional options The wool wash cycle of this machine has been approved by Woolmark for the washing of machine washable Woolmark products provided that the products are washed according to the instructions WooLmaRK on the garment label and those issued by the manufacturer of this washing machine M0801 Notes Neutral detergent is recommended The wool cycle features gentle tumbling and low speed spin for garment care ve Information of main washing programmes at half load Remaining moisture PRET program Time in minutes _ Remaining moisture Water in Liter Energy in kWh 1400rpm 1200rpm 1000rpm Marking marking Coton OO Hie to use washer SmartDiagnosis function is available only for the products with a SmartDiagnosis mark Cotton Press amp Hold 3sec for Tub Clean Function Cotton Eco y Sports Wear Mix _ Delicate Z wa E EY Time Delay Detecting Wash Rinse Spin ae Easy Care y Wool Medic Rinse Intensive me 2 gt Duvet Intensive 60 800 60 Pre Wash 400 om 40 Crease Care Skin Care Quick 30 No Spin 20 j Rinse Hold
10. the lower cover cap PUT janenance E Dispenser drawer After a while detergents and fabric softeners leave a deposit in the drawer It should be cleaned from time to time with a jet of running water If necessary it can be removed completely from the machine by pressing the catch downwards and by pulling it out To facilitate cleaning the upper part of the fabric softener compartment can be removed WE The drawer recess Detergent can also accumulate inside the recess which should be cleaned occasionally with an old toothbrush Once you have finished cleaning replace the drawer and run a rinse cycle without laundry E The washing drum If you live in a hard water area limescale may continuously build up in places where it cannot be seen and thus not easily removed Over time the build up of scale clogs appliances and if it is not kept in check these may have to be replaced Although the washing drum is made of Stainless steel specks of rust can be caused by small metal articles paper clips safety pins which have been left in the drum The washing drum should be cleaned from time to time If you use descaling agents dyes or bleaches make sure they are suitable for washing machine use Descaler may contain chemicals that may damage part of your washing machine Remove any spots with a stainless steel cleaning agent Never use steel wool TT E Cleaning your washer 1 Ext
11. time j i L is displayed is displayed When time delay is selected it shows the Recommended program by manufacturer remaining time to finish the selected program i F14B8Q TD F10 12B8Q W A 1 9 TD W A 1 9 2 Self diagnosis display Cotton 95 C Cotton 60 C If the machine encounters a fault during Cotton Eco operation the associated fault will be imix so 80 displayed Mix PE Water pressure sensing enor EE Problem of overfilling water IL Door is not closed Baby Care _ dE Sports Wear E Water inlet rouble ME Drainage trouble lne tenseso 0 o i Quick 30 i CE Over load in motor ir i Huerload t The washing time may vary by the amount of LE Overload in motor laundry water pressure water temperature and IE The washer experienced a power failure other washing conditions If an unbalanced load is detected or if the suds removing program operates the wash time may If these error letters are displayed please refer to be extended the troubleshooting page 26 and follow the guide fc Pitan Before cleaning the washer interior unplug the electrical power cord to avoid electrical shock to avoid electrical shock hazards When disposing of the appliance cut off the mains cable and destroy the plug Disable the door lock to prevent young children being trapped inside E The water inlet filter J error message will blink on t
12. A 1 9 F10B8Q TD W A 1 9 1 Spin selection 2 No spin Spin Speed is available according to the If No spin is selected the washer stops after program as follows draining water F14B8Q TD W A 1 9 Cotton Intensive 60 Quick 30 Rinse Spin 3 Rinse Hold Skin Care Mix Cotton Eco Rinse Hold No Spin 400 800 1400 Sportswear Delicate Wool 6 Baby Care Duvet Easy care e Rinse Hold is selected by pressing the spin button repeatedly this function leaves clothes in the machine suspended in the water after a rinse without entering into spin Rinse Hold No Spin 400 800 7 e To proceed through to a drain or spin once F12B8Q TD W A 1 9 the rinse hold function is completed using to Cotton Intensive 60 Quick 30 Rinse Spin Program dial and Spin button to the required Skin Care Mix Cotton Eco Soinh Rinse Hold No Spin 400 800 1200 p Sportswear Delicate Wool Baby Care The required lamp will light up for identification Duvet Easy care Rinse Hold No Spin 400 800 F10B8Q TD W A 1 9 Cotton Intensive 60 Quick 30 Rinse Spin Skin Care Mix Cotton Eco Rinse Hold No Spin 400 800 1000 Sportswear Delicate Wool 6 Baby Care Duvet Easy care Rinse Hold No Spin 400 800 20 ow to use washer Water Temp e By pressing the Temp button the water temperature can be selected Cold 20 C 40 C 60 C 95 C e Water temperature can be selected
13. Cold Rinse Spin Spin Temp 1 Cotton automatically 2 Manual Selecting selected upon power on e Press the Power button to start e Press the Power button to start Press the Start Pause button e Select the conditions which you want to use by turning the program dial and Initial conditions pressing each button Wash main wash For selecting the each conditions please Rinse 3 3 times refer to the pagel6 page21 Spin Press the Start Pause button 1400rpm F14B8Q TD W A 1 9 1200rpm F12B8Q TD W A 1 9 1000rpm F10B8Q TD W A 1 9 Time Delay Water temperature 60 C Program Cotton 3 Beep on off e The Beep on off function can be set by pressing Time Delay button when the washing machine is working About three seconds H ie to use washer Cotton Cotton Eco Sports Wear Mix _ Delicate Easy Care Wool Duvet Intensive 60 Quick 30 Rinse Spin 2 Press amp Hold 3sec for Tub Clean Function Medic Rinse 1200 800 Pre Wash 400 No Spin Rinse Hold 1 10 6 2 7 3 1 Dial Program 2 Button Start Pause 3 Button Spin 4 Button Temperature Power 1 Power Press the Power button to turn power on and off e To cancel the Time Delay function the power button should be pressed 2 Initial Program e When the Power
14. button is pressed the washer is ready for Cotton program And the other initial conditions as follows So if you want to advance into the washing cycle without changing the program just press the Start Pause button and then the washer will proceed E Initial program F14B8Q TD W A 1 9 Cotton Program Main wash Normal Rinse 1400 rpm 60 C F12B8Q TD W A 1 9 Cotton Program Main wash Normal Rinse 1200 rpm 60 C F10B8Q TD W A 1 9 Cotton Program Main wash Normal Rinse 1000 rpm 60 C 5 Button Power 6 Button Medic Rinse 7 Button Pre Wash 8 Button Intensive Mix Easy Care Duvet Skin Care TI Baby Care Time Delay _ a PA ei Seite Detecting Wash Rinse Spin Intensive 95 C me E 40 Crease Care 20 Cold Temp 4 8 6 9 11 12 Button Crease Care 9 10 Child Lock 11 Tub Clean 12 Button Time Delay Delicate Wool a Intensive 60 Quick 30 Rinse Spin 13 programs are available according to the laundry type e Lamp will light up to indicate selected program When Start Pause button is pressed the Cotton program is automatically selected By turning the Program dial the program is selected in order of Cotton Sports Wear Delicate Wool Intensive 60 Quick 30 Rinse Spin Baby Care Skin Care Duvet Easy Care Mix Cotton Eco R
15. e For wall door and floor modeling is required 10cm rear 2cm right amp left side Do not place or store laundry products on top of washer at any times They can damage the finish or controls Drain Hose E Positioning Install the washer on a flat hard floor Make sure that air circulation around the washer is not impeded by carpets rug etc e Never try to correct any unevenness in the floor with pieces of wood cardboard or similar materials under the washer e If it is impossible to avoid positioning the washer next to a gas cooker or coal burning stove an insulation 85x60cm covered with aluminum foil on the side facing the cooker or stove must be inserted between the two appliance e The washer must not be installed in rooms where the temperature can drop below 0 C e Please ensure that when the washer is installed it is easily accessible for the engineer in the event of a breakdown e Adjust all four feet using the transit bolt spanner provided ensuring the appliance is stable and a clearance of approximately 20mm is left between the top of the washer and the underside of the work top E BS Plug Safety Details For U K User IMPORTANT THE WIRES IN THIS MAINS LEAD ARE COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE GREEN AND YELLOW EARTH BLUE NEUTRAL BROWN LIVE This appliance must be earthed Green and Yellow Earth Brown Live Blue Neutral As the colours of the wires in the mains lead of
16. efore discarding an old machine unplug it Render To avoid such a result carefully follow the garment the plug useless Cut off the cable directly behind manufacturer s wash and care instructions the appliance to prevent misuse Do not wash or dry articles that have been cleaned When a product was under water Please call in washed in soaked in or spotted with service center The risk of electric shock and fire Do not push down the door excessively when washer door open This could topple over the washer SAVE THESE INSTRUCTIONS GROUNDING INSTRUCTIONS This appliance must be grounded In the event of malfunction or breakdown grounding will reduce the risk of electric shock by providing a path of least resistance for electric current This appliance is equipped with a cord having an equipment grounding conductor and grounding plug The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinance Do not use an adapter or otherwise defeat the grounding plug If you don t have the proper outlet consult an electrician WARNING Improper connection of the equipment grounding conductor can result in risk of electric shock Check with a qualified electrician or serviceman if you are in doubt as to whether the appliance is properly grounded Do not modify the plug provided with the appliance if it does not fit the outlet have a proper outlet installed b
17. egarding to the laundry type for each program Please refer to the pagel4 Hie to use washer Start Pause 1 Start e This Start Pause button is used to start wash cycle or pause the wash cycle 2 Pause If temporary stop of wash cycle is needed press the Start Pause button When in Pause the power is turned off automatically after 4 minutes NB The door will not open before 1 to 2 minutes when Pause is selected or at the end of the wash cycle Door Lock Detecting Wash Rinse Spin e Lights whenever the door of the washer is locked The door can be unlocked by pressing the Start Pause button to stop the washer e The door can be opened after a short delay Detecting x 7 Cl fe ee Detecting Wash Rinse Spin e While the Detecting is shown in the display the machine rotates slowly and detects how many laundries are loaded in the drum It will take a few seconds Available in Cotton Baby Care Skin Care Easy care Mix Cotton Eco 18 Option Medic Rinse Intensive e E Pre Wash Crease Care H ae By pressing the Option button all Option functions may be selected 1 Medic Rinse e For high effectiveness or more purity in rinse operation you can choose Medic Rinse option It can be chosen in all course with the exception of Sports Wear Delicate Wool Intensive 60 Quick 30 Duvet 2 Pre Wash If the laundry is heavily s
18. eparate white fabrics from colored fabrics Lint Lint producers Collectors Wash lint producers and lint collectors separately 3 Caring before loading E Combine large and small items in a load Load large items first Large items should not be more than half the total wash load Do not wash single items This may cause an out of balance load Add one or two similar items Check all pockets to make sure that they are empty Items such as nails hair clip matches pens coins and keys can damage both your washer and your clothes Close zippers hooks and strings to make sure that these items don t snag on other clothes Pre treat dirt and stains by brushing a little detergent dissolved in water onto stains like collars and cuffs to help shift dirt Check the folds of the flexible gasket gray and remove any small articles if any e Check inside of the drum and remove any left items in it for next wash cycle e Remove any clothing or items on the flexible gasket to prevent clothing and the gasket damages Pyading detergent E Adding detergent and fabric softener 1 The Dispenser Drawer e Main wash only gt LL Pre Wash Main Wash gt _L LL Keep all washing detergents away from children as there is danger of poisoning Too much detergent bleach or softener may cause an overflow Detersentfor Fabie Detergent Be sure to use the appropriate amount of main wash softener for pre wash
19. erior Proper care of your washer can extend its life The outside of the machine can be cleaned with warm water and a neutral non abrasive household detergent Immediately wipe off any spills Wipe with damp cloth Try not to hit surface with sharp objects IMPORTANT Do not use methylated spirits diluents or similar products 2 Interior Dry around the washer door opening flexible gasket and door glass Run washer through a complete cycle using hot water Repeat process if necessary KAD Remove hard water deposits using only cleaners labeled as safe for washing machine E Winterizing instructions If the washer is stored in an area where freezing may occur or moved in freezing temperatures follow these instructions to prevent damage to the washer 1 Turn off water supply tap 2 Disconnect hoses from water supply and drain water from hoses 3 Plug electrical cord into a properly grounded electrical outlet 4 Add igallon 3 8L of nontoxic recreational vehicle RV antifreeze into an empty wash drum Close the door Wi Set spin cycle and let washer spin for 1minute to drain out all water Not all of the RV antifreeze will be expelled Unplug electrical power cord dry the drum interior and close the door Remove dispenser drawer drain and dry excessive water from the compartments Store washer in an upright position O on To remove antifreeze from washer after storage run empty washer through a co
20. he control panel when water does not enter the detergent drawer If water is very hard or contains traces of lime deposit the water inlet filter may become clogged It is therefore a good idea to clean it from time to time 1 Turn off the water tap 2 Unscrew the water inlet hose 3 Clean the filter using a hard bristle brush 4 Tighten up the inlet hose PA jentenanee E The drain pump filter The drain filter collects threads and small objects left in the laundry Check regularly that the filter is clean to ensure smooth running of your machine A CAUTION First drain using the drain hose and then open the pump filter to remove whatever any threads or objects Be careful when draining if the water is hot AA CAUTION Do not open filter in half only Filter must be turned off and closed fully to avoid leakage Allow the water to cool down before cleaning the drain pump carrying out emergency emptying or opening the door in an emergency 1 Open the lower cover cap pull out the hose 2 Unplug the drain plug allowing the water to flow out At this time use a vessel to prevent water flowing on to the floor When water does not flow any more turn the pump filter open to the left 3 Remove any extraneous matter from the pump filter 4 After cleaning turn the pump filter right till the end to meet white lines on the filter and pump body Then insert the drain plug to the hose 5 Close
21. loor and then check that the appliance is perfectly level use a spirit level X After the washer is level tighten the lock nuts up towards of the base of the washer All lock nuts must be tightened l In the case that the washing machine is installed on a raised P i platform it must be securely fastened in order se 2e to eliminate the risk that it might fall off Diagonal Check When pushing down the edges of the washing machine top plate diagonally the machine should not move up and down at all Please check both of two directions If machine rocks when pushing the machine top plate diagonally adjust the feet again E Concrete floors The installation surface must be clean dry and level Install washer on a flat hard floor E Tile floors Slippery floors Position each foot on the Tread Mate and level the machine to suit Cut Tread Mate into 70x70 mm sections and stick the pieces on to the dry tile where machine is to be placed X Tread Mate is a self adhesive material used on ladders amp steps that prevents slipping E Wooden floors Suspended floors e Wooden floors are particularly susceptible to vibration To prevent vibration we recommend you place rubber cups under each foot at least 15mm thick under the washer secured to at least 2 floor beams with screws If possible install the washer in one of the corners of the room where the floor is more stable X Insert the rubber cups to reduce vibration
22. mplete cycle using detergent Do not add wash load 26 i ee oiiaatootlng guide This washing machine is equipped with automatic safety functions which detect and diagnose faults at an early stage and react appropriately When the machine does not function properly or does not function at all check the following points before you contact your service provider Rattling and e Foreign objects such as coins or Stop washer and check drum clanking noise safety pins maybe in drum or and drain filter pump If noise continues after washer is restarted call your authorised service centre Thumping sound e Heavy wash loads may produce If sound continues washer is a thumping sound This is usually probably out of balance Stop and normal redistribute wash load Vibrating noise Have all the transit bolts and If not removed during packing been removed installation Refer to Installation guide Are all the feet resting firmly on for removing transit bolts the ground Wash load may be unevenly distributed in drum Stop washer and rearrange wash load Water leaks Fill hoses or drain hose are loose Check and tighten hose connections at tap or washer e House drain pipes are clogged Unclog drain pipe Contact plumber if necessary Oversudsing Too much detergent or unsuitable detergent may cause excessive foaming which may result in water leaks Water does not enter Water supply is not adequate in Check anothe
23. nit may be impaired at temperatures below freezing point If the appliance is delivered in the winter months and temperatures are below freezing Place the washing machine at room temperature for a few hours before putting it into operation CAUTION This appliance is not intended for use by young children or infirm persons without supervision Young Children should be supervised to ensure that they do not play with appliance CAUTION CAUTION concerning the Power Cord Most appliances recommend they be placed upon a dedicated circuit that is a single outlet circuit which powers only that appliance and has no additional outlets or branch circuits Check the specification page of this owner s manual to be certain Do not overload wall outlets Overloaded wall outlets loose or damaged wall outlets extension cords frayed power cords or damaged or cracked wire insulation are dangerous Any of these conditions could result in electric shock or fire Periodically examine the cord of your appliance and if its appearance indicates damage or deterioration unplug it discontinue use of the appliance and have the cord replaced with an exact replacement part by an authorized servicer Protect the power cord from physical or mechanical abuse such as being twisted kinked pinched closed in a door or walked upon Pay particular attention to plugs wall outlets and the point where the cord exits the appliance If The appliance is supplied from a co
24. oiled Pre Wash course is effective Pre Wash is available in Cotton Baby Care Skin Care Easy Care Mix Cotton Eco 3 Intensive If the laundry is heavily soiled Intensive option is effective e By selecting the Intensive option the wash time may be extended depending on the program selected 4 Crease Care e If you want to prevent crease select this button with spin speed The required lamp will light up for identification Hie to use washer Child Lock amp Medic Rinse Pre Wash If you choose to lock the buttons on the control assembly to prevent tampering this function may be selected e Child Lock can be set by pressing the Medic Rinse button and Pre Wash button simultaneously About three seconds To deactivate Child Lock system press Medic Rinse and Pre Wash buttons simultaneously again About three seconds e To change to the desired program whilst in child lock mode 1 Press both Medic Rinse and Pre Wash together once again About three seconds 2 Press the Start Pause button 3 Select the desired program and press the Start Pause button again Medic Rinse F3 Change the Come desired gt t program e The child lock can be set at any time and it can be deactivated only by using child lock cancel process Turning the power off and operational errors will not affect child lock Tub Clean Intensive C
25. ontact with the tap Then rubber packing within in the Bias tighten the 4 screws hose can adhere completely to iga i rare the tap and then tighten it by packing screwing it to the right Upper Connector Fixing screw Water supply L hose E Normal Tap without thread amp one touch type inlet hose 1 Untighten the upper connector 2 Push the upper connector up 3 Connect the water supply screw till the rubber packing is in hose to the middle connector tight contact with the tap Then pushing the plate down Rubber tighten the 4 screws Middle connector In case the diameter of the tap is large remove the guide plate Guide plate e Turn the middle connector not To separate the water supply to have water leaked hose from the middle connector shut off the tap Then pull the inlet hose down pushing the plate down Connector e Make sure that the rubber seal is inside the hose connector Rubber seal Used the horizontal tap Horizontal tap Fy e Your machine comes with only cold water connection Extension tap e Make sure that there are no kinks in the hose and that it ae ae is not crushed Square tap SF 8 T essllation This equipment is not designed for maritime use or for use mobile installations such as caravans aircraft etc Turn off the stopcock if the machine is to be left for any length of time e g holiday
26. r tap in the house washer or it enters area slowly e Water supply tap is not Fully open tap completely open e Water inlet hose s are kinked Straighten hose The filter of the inlet hose s Check the filter of the inlet hose clogged Water in the washer Drain hose is kinked or clogged Clean and straighten the drain hose does not drain or rie drains slowly The drain filter is clogged Clean the drain filter Bs onesie ng guide Washer does not e Electrical power cord may not start be plugged in or connection may be loose e House fuse blown circuit breaker tripped or a power outage has occurred e Water supply tap is not turned on Washer will not spin Check that the door is firmly shut Door does not open Wash cycle time delayed Fabric softener Too much softener may cause overflow an overflow Softeners dispensed too early 28 Make sure plug fits tightly in wall outlet Reset circuit breaker or replace fuse Do not increase fuse capacity If problem is a circuit overload have it corrected by a qualified electrician Turn on water supply tap Close the door and press the Start Pause button After pressing the Start Pause button it may take a few moments before the clothes washer begins to spin The door must lock before spin can be achieved Add 1 or 2 similar items to help balance the load Rearrange load to allow proper spinning Once machine has sta
27. rd extension set or an electrical portable outlet device the cord extension set on electrical portable outlet device must be positioned so that it is not subject to splashing or ingress of moisture Washing Machine is to be connected to the water mains using new hose sets and old hose sets should not be used E Connecting water supply hose gt Water supply pressure must be between 30kPa and 1000kPa 0 3 10kgf cm gt Don t strip or crossthread when connecting Inlet hose to the valve gt If the water supply pressure is more than 1000kPa a decompression device should be installed e Two rubber seals are supplied with the water inlet hoses They are used for preventing water leaks e Make sure the connection to taps is tight enough e Periodically check the condition of the hose and replace the hose if necessary Sealing e Make sure that there is no kink on the hose and that it is washer not crushed Xi After completing connection if water leaks from the hose repeat the same steps Use the most conventional type of faucet for water supply In case the faucet is square or too big remove the spacing ring before inserting the Dp faucet into the adaptor Bp ostaitation E Normal Tap without thread amp screw type inlet hose 1 Unscrew the fixing screw to 2 Push the connector up till the 3 Push the water supply hose attach the tap rubber packing is in tight vertically upwards so that the c
28. rease Care J Tub Clean course can be set by pressing and holding Intensive and Crease Care button simultaneously When Tub Clean course is set display and all buttons are inoperable L l O OC TUB CLEAN is special cycle to clean the inside of the washer This cycle uses higher water level with higher spin speed Perform this cycle regularly How to use the Tub Clean cycle 1 Remove any clothing or items from the washer and close the door 2 Open the dispenser drawer and add Anti limescale Calgon to the Main wash compartment NOTE Do not add any detergent to the detergent compartments Excessive suds may generate and leak from the washer 3 Close the dispenser drawer slowly 4 Power On and then press and hold Intensive and Crease Care button for 3 seconds then gi is displayed in LED 5 Press the Start Pause button to start 6 After the cycle is complete leave the door open to dry around the washer door opening flexible gasket and door glass A CAUTION If there is a small child be careful not to leave the door open for too long Hie to use washer Spin T After selecting the spin course the spin speed can be No Spin chosen by pressing Rinse Hold the spin button 1200 800 400 No Spin 800 b gt 400 No Spin Rinse Hold m Rinse Hold i Spin Spin se F14B8Q TD W A 1 9 F12B8Q TD W
29. rted the door cannot be opened for safety reasons Check if the Door Lock icon is illuminated You can safely open the door after the Door Lock icon turns off The washing time may vary by the amount of laundry water pressure water temperature and other usage conditions If the imbalance is detected or if the suds removing program works the wash time shall be increased Follow softener guidelines to ensure appropriate amount is used Do not exceed the maximum fill line Close the dispenser drawer slowly Do not open the drawer during the wash cycle OT euhleshostny guide e Water supply is not adequate in area Check another tap in the house e Water supply taps are not completely open Fully open tap e Water inlet hose s are kinked Straighten hose s e The filter of the inlet hose s are clogged Check the filter of the inlet hose Drain hose is kinked or clogged Clean and straighten the drain hose SASS The drain filter is clogged Clean the drain filter Load is too small Add 1 or 2 similar items to help Load is out of balance balance the load The appliance has an imbalance detection and Rearrange load to allow proper correction system If individual heavy articles spinning are loaded ex bath mat bath robe etc this system may stop spinning or even interrupt the spin cycle altogether If the laundry is still too wet at the end of the cycle add smaller articles of la
30. s the product is covered by the European Directive 2002 96 EC All electrical and electronic products should be disposed of separately from the municipal waste stream via designated collection facilities appointed by the government or the local authorities The correct disposal of your old appliance will help prevent potential negative consequences for the environment and human health For more detailed information about disposal of your old appliance please contact your city office waste disposal service or the shop where you purchased the product What Is Not Covered e Service trips to your home to teach you how to use the product If the product is connected to any voltage other than that shown on the rating plate If the fault is caused by accident neglect misuse or Act of God If the fault is caused by factors other than normal domestic use or use in accordance with the owner s manual e Provide instruction on use of product or change the set up of the product If the fault is caused by pests for example rats or cockroaches etc e Noise or vibration that is considered normal for example water drain sound spin sound or warming beeps e Correcting the installation for example levelling the product adjustment of drain e Normal maintenance which recommended by the owner s manual e Removal of foreign objects substances from the machine including the pump and inlet hose filter for example grit nails
31. sher door closed or try to force recommended in the user maintenance instructions the door open when locked This could result in or published user repair instructions that you damage to the washer understand and have the skills to carry out e When the machine runs high temperature the front Keep the area underneath and around your door may be very hot Don t touch it appliances free of combustible materials such as To minimize the possibility of electric shock unplug lint paper rags chemicals etc this appliance from the power supply or disconnect Close supervision is necessary if this appliance is the washer at the household distribution panel by used by or near children Do not allow children to removing the fuse or switching off the circuit breaker play on with or inside this or any other appliance before attempting any maintenance or cleaning Keep small animals away from the appliance e When unplugging power cord do not pull out by Do not leave the washer door open grasping the cord Otherwise the power cord may An open door could entice children to hang on the be damaged door or crawl inside the washer Never attempt to operate this appliance if it is e Never reach into washer while it is moving Wait damaged malfunctioning partially disassembled or until the drum has completely stopped has missing or broken parts including a damaged The laundry process can reduce the flame retardant cord or plug of fabrics B
32. st results avoid oversudsing Do not let the detergent harden Doing so may lead to blockages poor rinse performance or bad odor e Full load according to manufacturer s recommendation e Part load 3 4 of the normal amount Minimum load 1 2 of full load e A water softener such as Anti limescale e g Calgon can be used to cut down on the use of detergent in extremely hard water areas Dispense according to the amount specified on the packaging First add detergent and then the water softener e Use the quantity of detergent as for soft water 1 Open the door and put tablets into the drum 2 Load the laundry into the drum and close the door F anction E Recommended courses according to the laundry type 60 C Cold to 95 C Color fast garments shirts nightdresses pajamas etc and normally soiled cotton load underwear 40 C Cotton Eco Cold to 60 C Medic Rinse 60 C Pre Wash j Crease Care Baby Care Laundry for infant 95 C pein Fabrics which will be in direct contact with the skin e g Skin Care underwear nappies towelling bed linen pillow and mattress covers Cold to 60 C Polyamide Acrylic Polyester Various kind of fabrics except special garments Silk delicate sports wear dark clothes wool Duvet Curtains Cotton bedding except special garments delicates wool silk etc with filling 40 C duvets pillows blankets Cold to 40
33. t to infestation by cockroaches or other vermin pay particular attention to keeping the appliance and its surroundings in clean condition at all times Any damage which may be cause by cockroaches or other vermin will not be covered by the appliance guarantee E Transit bolts The appliance is fitted with transit bolts to prevent internal damage during transport e Packing and all transit bolts must be removed before using the washer i When unpacking the base be sure to remove the additional packing support in the middle of the base packing E Removing transit bolts 1 To prevent internal damage during transport the special 4 bolts are locked Before operating the washer remove the bolts along with the rubber bungs If they are not removed it may cause heavy vibration noise and malfunction 2 Unscrew the 4 bolts with the spanner supplied Washer Base Packing 7 ral 3 Take out the 4 bolts along with the rubber bungs by slightly twisting the bung Keep the 4 bolts and the spanner for future use e Whenever the appliance is transported the transit bolts must be refitted 4 Close the holes with the caps supplied pintaan E Installation place requirement Level floor Allowable slope under entire washer is 1 Power outlet Must be within 1 5 meters of either side of location of washer Do not overload the outlet with more than one appliance Additional Clearanc
34. this apparatus may not correspond with the coloured markings identifying the terminals in your plug proceed as follows The wire which is coloured Green and Yellow must be connected to the terminal in the plug which is marked with the letter E or by the earth symbol S or coloured Green or Green and Yellow The wire which is coloured Blue must be connected to the terminal which is marked with the letter N or coloured Black The wire which is coloured Brown must be connected to the terminal which is marked with the letter L or coloured Red Ifa 13 amp BS 1363 plug is used fit a 13 amp BS 1362 fuse 6 pintaan Electrical connection 1 Do not use an extension cord or double adapter 2 If the supply cord is damaged it must be replaced by the manufacturer or its service agents or similarly qualified person in order to avoid a hazard 3 Always unplug the machine and turn off the water supply after use 4 Connect the machine to an earthed socket in accordance with current wiring regulations 5 The appliance must be positioned so that the plug is easily accessible Repairs to the washing machine must only be carried out by qualified personnel Repairs carried out by inexperienced persons may Cause injury or serious malfunctioning Contact your local service center Do not install your washing machine in rooms where temperature below freezing may occur Frozen hoses may burst under pressure The reliability of the electronic control u
35. u perfect results every time ontents aa oa ET o AAEN A ANE ERE ET EE APT oe AE AAE EENE 3 TA EE PEARSA E ase A AS EA AA A AA E EE E 4 IPISTANATION EEN AN A AA I ENEAN AEN 5 Garo Dagro WASTING sena 11 PARTE Mice tied ASE AD ca case E NT A OAA E AI A A VE aria ey 12 E a A A A E A 14 HOW 10 USO WASIG ssicesavisxncrsaxiavsccnirsananerakaanaas 16 WGINENANCS nainn NDN 23 TROUDISSHOGUTG TUGE naaa O 2z ESE E E aa EEE E EA 31 20 WV fiii ings READ ALL INSTRUCTIONS AND EXPLANATION OF THE INSTALLATION BEFORE USE For your safety the information in this manual must be followed to minimize A WARNING the risk of ae explosion electric shock or to prevent property damage personal injury or loss of life IMPORTANT SAFETY INSTRUCTIONS WARNING To reduce the risk of fire electric shock or injury to persons when using the washer follow basic precautions including the following Before installation check exterior damages If ithas combustible or explosive substances such as wax do not install oil paint gasoline degreasers dry cleaning Do not install or store the washer where it will solvents kerosene etc which may ignite or be exposed to the weather explode Oil may remain in the tub after a whole Do not tamper with controls cycle resulting in fire during drying So do not load Do not repair or replace any part of the washer oiled clothes or attempt any servicing unless specifically Do not slam the wa
36. undry to balance the load and repeat the spin cycle Close the door Is the door opened If gE is not released call for service Unplug the power plug and call for service Fey Water overfills due to the faulty water valve Close the water tap Unplug the power plug Call for service e Water level sensor has malfunctioned cc Over load in motor ma Over load in motor pa pa The washer experienced a power failure Restart the cycle Be oubieshootiny guide vw SmartDiagnosis function is available only for the products with a SmartDiagnosis mark NOTE Incase of a mobile phone with static option the smart diagnosis function might not operate E Using SmartDiagnosis e Only use this feature when instructed to do so by the call center The transmission sounds similar to a fax machine and so has no meaning except to the call center e SmartDiagnosis cannot be activated if the washer does not power up If this happens then troubleshooting must be done without SmartDiagnosis lf you experience problems with your washer call to Customer information center Follow the call center agent s instructions and do the following steps when requested 1 Press the Power button to turn on the washer Do not press any other buttons or turn the cycle selector knob 2 When instructed to do so by the call center place the mouthpiece of your phone very close to the Power button
37. y a qualified electrician Power Plug If the supply cord is damaged it must be replaced by the manufacturer or its service agents or a similarly qualified person in order to avoid a hazard Drawer For detergent and fabric softener Drain Hose Drum Door Drain Pump Filter Lower cover Drain Plug Adjustable Feet Lower Cover Cap E Name Front loading washing machine WE Power supply 220 240V 50Hz E Size 600mm W x550mm D x 850mm H E Weight 62kg E Max Watt 2100W 0 33W The off mode The left on mode E Wash capacity 7kg F14 12 10B8QD W A 1 9 8kg F14 12 10B8TD W A 1 9 E Spin speed Rinse Hold No Spin 400 800 1400 F14B8Q TD W A 1 9 Rinse Hold No Spin 400 800 1200 F12B8Q TD W A 1 9 Rinse Hold No Spin 400 800 1000 F10B8Q TD W A 1 9 E Water consumption 49 0 F14 12 10B8QD W A 1 9 56 2 F14 12 10B8TD W A 1 9 WE Permissible water pressure 0 3 10kgf cm 80 1000kPa The appearance and specifications may be varied without notice to raise the units quality E Accessories as Sl Spanner 1 stallation Install or store where it will not be exposed to temperatures below freezing or exposed to the weather Properly ground washer to conform with all governing codes and ordinances The base opening must not be obstructed by carpeting when the washing machine is installed on a carpeted floor In countries where there are areas which may be subjec
Download Pdf Manuals
Related Search