Home

Chief KTC440S flat panel desk mount

image

Contents

1. 27 1 2 ARRAY ASSEMBLY Dual 34 1 2 B ARRAY ASSEMBLY Triple 42 1 2 ARRAY ASSEMBLY Triple 54 1 CENTRIS HEAD ASSEMBLY Pole Mount 2 D DESK CLAMP 1 1 1 1 1 1 1 1 E SHEATH Cable Management 8 1 1 2 1 1 2 2 2 F POLE Mount Freestanding 14 1 1 1 1 G POLE Mount Freestanding 28 1 1 1 1 H BUMPER 6 6 6 6 6 6 6 6 J KEY Hex 5 32 1 1 1 1 6 1 1 1 K KEY Hex 3 16 1 L KEY Hex 7 32 1 1 1 1 1 1 1 1 M CLAMP Pole 2 Pipe 1 1 1 1 2 2 2 N CLAMP Back Casting 2 P SCREW Phillips Pan Head M4 x 12mm 8 8 8 12 12 24 16 16 Q SCREW Phillips Pan Head M4 x 20mm 8 8 8 12 12 24 16 16 R SCREW Phillips Pan Head M4 x 30mm 8 8 8 12 12 24 16 16 5 SPACER Nylon 3 8 used with item Q 8 8 8 12 12 24 16 16 SPACER Nylon 3 4 used with item R 8 8 8 12 12 24 16 16 U SCREW Button Head Cap 1 4 20 x 3 4 2 2 2 2 4 4 4 V SCREW Button Head Cap 1 4 20 x 1 1 4 6 Ww SCREW Flat Head Cap 3 8 16 x 1 1 1 1 1 1 1 1 1 X WASHER Flat 1 4 2 2 2 2 4 4 4 Y PIPE CAP 1 75 OD 1 1 1 1 1 1 1 1 Installation Instructions KTC SERIES TOOLS REQUIRED FOR INSTALLATION 2 5 32 3 16 4 included tee included with 230 model only included PARTS QN REFER TO TABLE 2 FOR QUANTITIES Pole mount assembly B Triple array assembly G D F x Desk clamp 8 14 gt Q a BB dI J K L H 7192 3 16 5 32 M N Bumper 2 pipe cl
2. this product outdoors SAVE THESE INSTRUCTIONS Installation Instructions KTC SERIES DIMENSIONS KTC 220 01M 8411 Y ur DISI 1145 63 piri 1 64 d 3 15 153 el s eM SO L3 AUN i nm a KTC SERIES Installation Instructions DIMENSIONS CONTINUED 3 63 a4 14 15 155 6 KTC 230 Installation Instructions KTC SERIES DIMENSIONS CONTINUED D KTC 325 pi 113 2 NM 7AN 13 25 pis Y 4 HICIIAT ai 145 KTC 330 20H pa 11 2111 15 A 6 4 EN t TE SCH KTC SERIES Installation Instru
3. two button head cap screws U using a 5 32 hex key J 3 Repeat steps 1 2 for additional array mount on KTC 330 440 and 445 4 Add pipe cap Y to top of pole F or G Pole Mount front with Array Figure 6 Display Installation Attach Centris Head to Flush Mount Display CAUTION If display uses a screw size other than those included in the kit DO NOT use the screws provided Using the wrong screws could result in damage to your monitor 1 Install two M4 x 12mm Phillips pan head screws P into two upper mounting holes in display back using 2 Phillips screwdriver See Figure 7 NOTE DO NOCT fully tighten at this time 2 Hang display on Centris head See Figure 8 3 Install bottom two M4 x 12mm Phillips pan head screws P through Centris head mounting holes and into lower mounting holes in display back 4 Tighten ALL four M4 x 12mm Phillips pan head screws P See Figure 9 11 KTC SERIES Installation Instructions Display Centris Head Figure 8 Centris Head Array Rail Figure 9 12 Attach Centris Head to Recessed Mount Display NOTE Refer to Table 1 to select the applicable screw and spacer combination 1 Uninstall end lock using the 5 32 hex key J See Figure 10 2 Slide Centris head off array rail S
4. INSTALLATION INSTRUCTIONS wg Si KTC 325 KTC 330 KTC 440 KTC 445 Horizontal and Vertical Desk Clamp Stands amp CHIEF KTC SERIES Our Mounts Your Vision KTC SERIES Installation Instructions DISCLAIMER Milestone AV Technologies and its affiliated corporations and subsidiaries collectively Milestone intend to make this manual accurate and complete However Milestone makes no claim that the information contained herein covers all details conditions or variations nor does it provide for every possible contingency in connection with the installation or use of this product The information contained in this document is subject to change without notice or obligation of any kind Milestone makes no representation of warranty expressed or implied regarding the information contained herein Milestone assumes no responsibility for accuracy completeness or sufficiency of the information contained in this document Chief and Centris are registered trademarks of Milestone AV Technologies All rights reserved A IMPORTANT SAFETY INSTRUCTIONS WARNING A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions CAUTION A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the corresponding instructions WARNING Failure to read thoroughly understand and follow all instructions can result in serious perso
5. V Technologies a Duchossois Group Company www chiefmfg com 05 13 USA International Europe Asia Pacific gt TU 6436 City West Parkway Eden Prairie MN 55344 800 582 6480 952 225 6000 877 894 6918 952 894 6918 Franklinstraat 14 6003 DK Weert Netherlands 31 0 495 580 852 31 0 495 580 845 Office No 1 on 12 F Shatin Galleria 18 24 Shan Mei Street Fotan Shatin Hong Kong 852 2145 4099 852 2145 4477 P
6. al position 1 Loosen Centris bracket rear adjustment knob See Figure 15 2 Slide Centris bracket with display left or right until properly positioned on array rail 3 Tighten Centris bracket rear adjustment knob Horizontal Adjustment Knob Figure 15 13 KTC SERIES Installation Instructions Display Pitch and Roll Adjustment To adjust display pitch or roll position 1 Loosen Centris bracket front adjustment knob See Figure 16 2 Tilt display up or down or adjust display roll left or right until properly positioned 3 Tighten Centris bracket front adjustment knob Pitch Roll Adjustment Knob Figure 16 CABLE MANAGEMENT The KTC Series mount includes cable management features used to properly route and secure display cables To use the cable management features 1 Connectcablesto display 2 Route cables through cable clips on array rail See Figure 17 3 Route cables down pole and away from mount and secure to pole using sheath E See Figure 17 Cable Clips wu ITPA Figure 17 4 Repeat steps 1 3 for additional array on KTC 330 440 and 445 14 Installation Instructions KTC SERIES 15 KTC SERIES Installation Instructions CHIEF Our Mounts Your Vision Chief Manufacturing a products division of Milestone AV Technologies 8800 002425Rev 00 2013 Milestone A
7. amp Back casting clamp lt T M x 30 S il M4 X 12 M4 X 20 S O e 8 N 2 5 8 W V X Y di iu 1 4 20 x 1 1 4 3 8 16 x 1 1 4 Pipe cap gt X KTC SERIES Installation Instructions INSTALLATION Desk Clamp Installation NOTE In order to reduce the chance of scratching to the mounting surface bumpers may be installed However installation of bumpers is optional 1 Remove adhesive from underside of bumpers H 2 Attach bumpers H to underside of desk clamp D See Figure 1 view from bottom Figure 1 3 Use 7 32 hex key J to install 3 8 16 x 1 flat head cap screw W through the opening on top of desk clamp D and into bottom of mounting pole F or G See Figure 1 4 Determine the location where desk clamp will be mounted WARNING Failure to keep all mounted equipment directly above the desk surface at all times can result in serious personal injury or damage to equipment All mounted equipment must remain directly above the surface of the desk in order to ensure and maintain a stable mount 5 Place desk clamp D over desired mounting location on desk See Figure 2 6 If there is not enough clearance behind the desk for the device to clear remove the bottom portion of the desk clamp by using 5 32 hex key L to remove 2 connecting screws See Figure 2 7 Reinstall bottom portion of the desk clamp if necessary by reinstalling 2 connecting screw
8. ctions DIMENSIONS CONTINUED D 115 HE 65 LI 535 12 7 IN P LH H d 3 00 16 KTC 440 yy Loh 04 i4 1 1 z 335 SED pu E H KTC 445 npo Y HIN l8 SE 62 WAY Installation Instructions KTC SERIES LEGEND Tighten Fastener Apretar elemento de fijaci n Befestigungsteil festziehen Apertar fixador Serrare il fissaggio Bevestiging vastdraaien Serrez les fixations Pencil Mark Marcar con lapiz Stiftmarkierung Marcar com lapis Segno a matita Potloodmerkteken Marquage au crayon Loosen Fastener Aflojar elemento de fijaci n Befestigungsteil l sen Desapertar fixador Allentare il fissaggio Bevestiging losdraaien Desserrez les fixations Drill Hole Perforar Bohrloch Fazer furo Praticare un foro Gat boren Percez un trou Phillips Screwdriver Destornillador Phillips Kreuzschlitzschraubendreher Chave de fendas Phillips Cacciavite a stella Kruiskopschroevendraaier Tournevis pointe cruciforme Adjust Ajustar Einstellen Ajustar Regolare Afstelle
9. ee Figure 11 Centris Head Square Nut Array Rail Centris Head Figure 11 3 Place display face down on aclean dry surface 4 Place four 3 8 or 3 4 nylon spacers S or T over four mounting holes in display back See Figure 12 5 Align Centris head mounting holes with four nylon spacers See Figure 12 6 Secure Centris head to display using four M4 x 20mm Phillips pan head screws Q or four M4 x 30mm Phillips pan head screws R See Figure 12 Installation Instructions KTC SERIES Centris Head Figure 12 7 Slide display with Centris bracket onto array rail See Figure 13 NOTE Repeat previous steps for each additional display 8 Reinstall end locks into mounting rail using the 5 32 hex key J See Figure 14 Display with Centris Bracket Array Rail Figure 13 Array Rail End Lock End Lock Retaining Screw Centris Head Figure 14 ADJUSTMENTS Display Adjustment The KTC Series mount allows horizontal pitch and rotational adjustment of each display The KTC Series mount also allows a full 360 deg of display rotation with a maximum pitch range of 15 up and 15 down The 3 16 hex key included with the KTC 230 mount is to be used to adjust the rotation on this model Display Horizontal Position Adjustment To adjust display horizont
10. n Ajuster Open Ended Wrench Llave de boca Gabelschl ssel Chave de bocas Chiave a punte aperte Steeksleutel Cl fourche Remove Quitar Entfernen Remover Rimuovere Verwijderen Retirez By Hand A mano Von Hand Com a m o A mano Met de hand la main Optional Opcional Optional Opcional Opzionale Optie En option y E d 3 Hex Head Wrench Llave de cabeza hexagonal Sechskantschl ssel Chave de cabeca sextavada Chiave esagonale Zeskantsleutel Cl t te hexagonale O 9 Q 09 Security Wrench Llave de seguridad Sicherheitsschl ssel Chave de Chiave di sicurezza Veiligheidssleutel Cl de s curit KTC SERIES Installation Instructions Table 1 Monitor Limits MONITOR LIMITS By MODEL DESCRIPTION 220 225 230 320 325 330 440 445 Weight 35 lbs 35lbs 35lbs 20lbs 15 lbs 15 lbs 20 lbs 15 lbs Max Screen Width 22 7 30 N A 18 24 5 18 22 7 30 Max Screen Height 28 28 19 3 28 28 18 5 18 5 18 5 Table 2 Parts QUANTITY By MODEL ITEM DESCRIPTION 220 225 230 320 325 330 440 445 A ARRAY ASSEMBLY Dual
11. nal injury damage to equipment or voiding of factory warranty It is the installer s responsibility to make sure all components are properly assembled and installed using the instructions provided WARNING Failure to provide adequate structural strength for this component can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the structure to which this component is attached can support five times the combined weight of all equipment Reinforce the structure as required before installing the component WARNING Failure to keep all mounted equipment directly above the desk surface at all times can result in serious personal injury or damage to equipment All mounted equipment must remain directly above the surface of the desk in order to ensure and maintain a stable mount WARNING Exceeding the weight capacity can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the weight of each monitor attached does not exceed the weight limit for each specific model Refer to Table 1 for the weight limits for each model WARNING Use this mounting system only for its intended use as described in these instructions Do not use attachments not recommended by the manufacturer WARNING Never operate this mounting system if it is damaged Return the mounting system to a service center for examination and repair WARNING Do not use
12. s underneath desk See Figure 2 10 behind desk Figure 2 8 Turn clamp screw until the clamp is secured to the desk as tightly as possible See Figure 3 Figure 3 Installation Instructions KTC SERIES Mount Assembly KTC 230 Assembly 1 Place front pole clamp with Centris Head C against pole G in approximate mounting location 2 Place three 1 4 20 X 1 1 4 button head cap screws V into rear pole clamp N and place against pole aligning with front pole clamp on Centris Head C See Figure 4 Figure 4 3 Equally tighten screws V against front pole mount and the rear pole clamp N See Figure 5 N S Keep equal distance between H mount and clamp when tightening Figure 5 4 Secure rear pole clamp N to Centris head s front pole mount C and pole G by tightening three button head cap screws V using 5 32 hex key J See Figure 4 5 Repeat steps 1 4 for additional Centris head Add pipe cap Y to top of pole F or G KTC 220 225 320 325 330 440 and 445 Assembly 1 Assemble pole clamp back M to pole mount front using two washers X and two 1 4 20 x 3 4 button head cap screws U using a 5 32 hex key J See Figure 6 2 Secure pole mount back M to pole mount front and pole by tightening

Download Pdf Manuals

image

Related Search

Related Contents

Kicker 2013 CompRT Subwoofer Owner's Manual  Porter-Cable 7414 Sander User Manual  Sem título-2 - Antenas Cromus  manuel d`installation et d`utilisation    Handbuch - MERK Sicherheitstechnik  Evaluation of SweSum for French texts  Trango Broadband M900S User's Manual  MANUEL D`UTILISATEUR  508519 Funk-Zwischenstecker CONNECT, Schalter  

Copyright © All rights reserved.
Failed to retrieve file