Bosch DIVAR IP 2000, 2 Festplatten
Contents
1. Warning Lithium battery Batteries that have been inserted wrongly can cause an explosion Always replace empty batteries with batteries of the same type or a similar type recommended by the manufacturer Handle used batteries carefully Do not damage the battery in any way A damaged battery may release hazardous materials into the environment Dispose of empty batteries according to the manufacturer s instructions 2013 09 V2 DOC Installation Manual Bosch Sicherheitssysteme GmbH DIVAR IP 2000 Safety precautions en 5 Warning Handling of lead solder materials used in this product may expose you to lead a chemical known to the State of California to cause birth defects and other reproductive harm Notice Electrostatically sensitive device To avoid electrostatic discharges the CMOS MOSFET protection measures must be carried out correctly When handling electrostatically sensitive printed circuits grounded anti static wrist bands must be worn and the ESD safety precautions observed Notice Installation should only be carried out by qualified customer service personnel in accordance with the applicable electrical regulations Disposal Your Bosch product has been developed and manufactured using high quality materials and components that can be reused This symbol means that electronic and electrical devices that have reached the end of their working life must be disposed of se2. configuration Notice If VRM is not available on the computer or the license check fails a corresponding error message is displayed You cannot continue working with Configuration Wizard 2013 09 V2 DOC Installation Manual Bosch Sicherheitssysteme GmbH DIVAR IP 2000 System setup first steps en 15 Passwords page Configuration Wizard PS Passwords R d Specify a password in order to prevent unauthorized access to your devices The administrator ecorder password has the highest level and protects all device settings live and operator passwords are set 5 Device Selection Password administrator to restrict the use of the device Network Confirm Password operator Confirm Recording Password live MEER Summary Confirm Date and Time Video Quality GEDE lt Back L ne Cancel This page allows you to specify a password to protect the devices from unauthorized access Enter the respective password confirm the password then click Next gt Bosch Sicherheitssysteme GmbH Installation Manual 2013 09 V2 DOC 16 en System setup first steps Recorder page DIVAR IP 2000 Configuration Wizard Passwords Recorder Device Selection Network Recorder information Date and Time Access Name Video Quality Type Recording Used channels Free channels Summary Storage space gaganada Soft
3. cords must include a grounding plug and must be plugged into grounded electrical outlets The unit has more than one power supply cord Disconnect both power supply cords before servicing to avoid electrical shock Bosch Sicherheitssysteme GmbH Installation Manual 2013 09 V2 DOC 6 en Safety precautions DIVAR IP 2000 Mainboard replaceable soldered in fuses Self resetting PTC Positive Temperature Coefficient fuses on the mainboard must be replaced by trained service technicians only The new fuse must be the same or equivalent as the one replaced Contact technical support for details and support Caution Mainboard Battery There is a danger of explosion if the onboard battery is installed upside down which will reverse its polarities This battery must be replaced only with the same or an equivalent type recommended by the manufacturer CR2032 Dispose of used batteries according to the manufacturer s instructions 1 3 ESD precautions Electrostatic Discharge ESD is generated by two objects with different electrical charges coming into contact with each other An electrical discharge is created to neutralize this difference which can damage electronic components and printed circuit boards The following measures are generally sufficient to neutralize this difference before contact is made to protect your equipment from ESD Do not use mats designed to decrease electrostatic discharge as protection from electri
4. sleeves which can come into contact with electrical circuits or be pulled into a cooling fan Remove any jewelry or metal objects from your body which are excellent metal conductors that can create short circuits and harm you if they come into contact with printed circuit boards or areas where power is present Warning Interruption of mains supply Voltage is applied as soon as the mains plug is inserted into the mains socket However for devices with a mains switch the device is only ready for operation when the mains switch ON OFF is in the ON position When the mains plug is pulled out of the socket the supply of power to the device is completely interrupted Warning Removing the housing To avoid electric shock the housing must only be removed by qualified service personnel Before removing the housing the plug must always be removed from the mains socket and remain disconnected while the housing is removed Servicing must only be carried out by qualified service personnel The user must not carry out any repairs Warning Power cable and AC adapter When installing the product use the provided or designated connection cables power cables and AC adaptors Using any other cables and adaptors could cause a malfunction or a fire Electrical Appliance and Material Safety Law prohibits the use of UL or CSA certified cables that have UL CSA shown on the code for any other electrical devices gt Bb Be D
5. ALT DELETE The Windows logon page is displayed 12 Enter the password The Welcome page of the Configuration Wizard is displayed 13 Configure the system using the Configuration Wizard To do this go through the wizard and follow the instructions on the screen See also Using Configuration Wizard page 13 Recovering the unit page 23 Using Configuration Wizard Intended use for Configuration Wizard is the quick and easy configuration of a smaller system Configuration Wizard helps you to achieve a configured system including VRM iSCSI system cameras recording profiles and user groups User groups and their permissions are configured automatically You can add or remove users and set passwords Configuration Wizard can access Management Server only on the local computer Configuration Wizard adds the local VRM automatically To achieve a quick configuration using the Configuration Wizard 1 On the default screen double click the Configuration Wizard icon The Welcome page is displayed 2 Run through the following pages of the wizard Bosch Sicherheitssysteme GmbH Installation Manual 2013 09 V2 DOC 14 en System setup first steps DIVAR IP 2000 Welcome page Configuration Wizard ant to Eau any ach ne features such as recording please refer to the manual and use the advanced mode in Configuration Manager Click Next gt to start configuring your devices gt Click Next gt to start the
6. Apply to store and confirm all settings Passwords operator password not set live password not set administrator password not set Recorder Recorder 160 10 127 103 Network IP address range 160 10 127 1 160 10 255 255 Subnet mask 255 255 0 0 Gateway 0 0 0 0 Date and Time Synchronized with computer Video Quality Quality setting Highest Recording Recording mode Day Continuous Recording mode Night Continuous Save Summary lt Back Apply Cancel This page displays a summary of all wizard settings Click Apply to activate the configuration 2013 09 V2 DOC Installation Manual Bosch Sicherheitssysteme GmbH DIVAR IP 2000 Recovering the unit en 23 5 Recovering the unit Following procedure describes how to restore the factory default image To restore the unit to factory default image 1 Start the unit and press F7 during the BIOS power on self test The Recovery menu is displayed Notice Make sure that aVGA monitor a keyboard and a mouse are connected to the unit 2 Select one of the following Initial to factory image all data will be deleted restores to factory default image and deletes all data on the HDDs or Restore to Factory image all data will not be deleted restores to factory default image data on the HDDs will not be deleted Note Windows performs the setup The screen displays the percentage of
7. C time SNTP server 1 000 Network Information Ffagga Time 3 26 21 PM Date Thursday April 11 2013 E Video Quality Time zone WW Europe Standard Time Date and time format dddd MM dd yyyy Recording Summary This page allows you to synchronize the device time with the computer time or a SNTP time server gt Click Next gt to continue Bosch Sicherheitssysteme GmbH Installation Manual 2013 09 V2 DOC 20 en System setup first steps DIVAR IP 2000 Video Quality page Configuration Wizard Passwords Video Quality R d Use the slider to choose your preferred live viewing picture quality The best matching encoder settings ecorder will be determined automatically Additionally you can set a limit for the maximum bandwidth allowed in your network Device Selection ay ay ley Bay ewan y a g Date and Time Low quality Medium quality High quality n Low bandwidth Medium bandwidth High bandwidth Low resolution Medium resolution High resolution Network bandwidth limit Recording E Summary Max bandwidth 2 Mbps T Limit maximum network bandwidth This page allows you to define the image quality for live viewing and to set the maximum bandwidth Click Next gt to continue 2013 09 v2 DOC Installation Manual Bosch Sicherheitssysteme GmbH DIVAR IP 2000 System setup first steps en 21 Recording page Passwords lay Recording R d F
8. DIVAR IP 2000 DIP 2040 00N DIP 2042 2HD DIP 2042 4HD BOSCH en Installation Manua DIVAR IP 2000 Table of contents Table of Contents en 3 1 Safety precautions 4 1 1 General safety precautions 4 1 2 Electrical safety precautions 5 1 3 ESD precautions 6 1 4 Operating precautions 6 2 System overview 7 2 1 Chassis features 7 2 2 Chassis components T 2 2 1 Chassis 7 2 2 2 Backplane 7 2 2 3 Power supply f 2 3 Device views 8 2 3 1 LED description front panel 9 2 3 2 LAN port LED description rear panel 10 3 Chassis setup and maintenance 11 3 1 Removing hard drive trays 11 3 2 Installing a hard drive 11 4 System setup first steps 12 4 1 Introduction 12 4 2 Setup instruction 12 4 3 Starting the application 12 4 4 Using Configuration Wizard 13 5 Recovering the unit 23 6 Additional documentation and client software 24 Bosch Sicherheitssysteme GmbH Installation Manual 2013 09 V2 DOC 4 en Safety precautions DIVAR IP 2000 1 1 Safety precautions Observe the safety precautions in this chapter General safety precautions Follow these rules to ensure general safety Keep the area around the system clean and free of clutter Place the chassis top cover and any system components that have been removed away from the system or on a table so that they won t accidentally be stepped on While working on the system do not wear loose clothing such as neckties and unbuttoned shirt
9. T Select all Update Next gt Cancel This page displays all network devices that are added to the system Clicking Update starts the scan process again gt Click Next gt to continue Bosch Sicherheitssysteme GmbH Installation Manual 2013 09 V2 DOC 18 en System setup first steps Network page DIVAR IP 2000 Configuration Wizard Passwords Recorder Device Selection geagaelzag Date and Time Video Quality Recording Summary Network If your devices and your network support DHCP IP addresses can be assigned automatically For older devices please specify a valid IP address range The address range needs to provide enough unassigned IP addresses for all devices to be configured Use DHCP Use the following IP address settings IP address range fi 60 10 1271 fi 60 10 255 255 Subnet mask 255 255 0 0 VW Set automatically Gateway 6 0 00 The selected recorder does not support DHCP lt Back L ne Cancel This page allows you to configure the network settings of connected devices gt Click Next gt to continue 2013 09 v2 DOC Installation Manual Bosch Sicherheitssysteme GmbH DIVAR IP 2000 System setup first steps en 19 Date and Time page Configuration Wizard Passwords Date and Time R d Choose whether to synchronize the device time and date with your current computer settings or an ecorder SNTP time server Device Selection P
10. ation 1 Connect the unit and the cameras to the network 2 Turn on the unit The Windows Storage Server 2008 R2 setup process starts 3 Select the appropriate language for the installation then click Next 4 In the Country or region Time and currency and Keyboard layout lists click the appropriate item then click Next The Microsoft Software License Terms and the EULA End User License Agreement are displayed 5 Accept the license terms then click Start Windows restarts 6 After restart is finished press CTR ALT DELETE The Windows logon page is displayed 7 Enter the default password WSS4Bosch 2013 09 V2 DOC Installation Manual Bosch Sicherheitssysteme GmbH DIVAR IP 2000 4 4 System setup first steps en 13 8 After entering the password a message is displayed that you must change the password before logging on the first time To confirm click OK 9 Change the password A series of scripts perform important setup tasks This can take several minutes Do not turn off the computer A page is displayed where you can perform initial Windows configuration tasks Note In case of password loss a system recovery must be performed as described in the installation manual The configuration must be done from scratch or must be imported 10 Click the Set time zone Configure networking and Provide computer name and domain link enter the appropriate information then click Close Windows restarts 11 Press CTR
11. cal shock Instead use rubber mats that have been specifically designed as electrical insulators Use a grounded wrist strap designed to prevent static discharge Keep all components and printed circuit boards PCBs in their antistatic bags until ready for use Touch a grounded metal object before removing the board from the antistatic bag Do not let components or printed circuit boards come into contact with your clothing which may retain a charge even if you are wearing a wrist strap Handle a board by its edges only Do not touch its components peripheral chips memory modules or contacts When handling chips or modules avoid touching their pins Put the mainboard and peripherals back into their antistatic bags when not in use For grounding purposes make sure your computer chassis provides excellent conductivity between the power supply the case the mounting fasteners and the mainboard 1 4 Operating precautions The chassis cover must be in place when the system is operating to assure proper cooling Out of warranty damage to the system can occur if this practice is not strictly followed Note Please handle used batteries carefully Do not damage the battery in any way A damaged battery may release hazardous materials into the environment Do not discard a used battery in the garbage or a public landfill Please comply with the regulations set up by your local hazardous waste management agency to dispose o
12. f your used battery properly 2013 09 V2 DOC Installation Manual Bosch Sicherheitssysteme GmbH DIVAR IP 2000 2 1 2 2 2 2 1 2 2 2 System overview en 7 System overview The DIVAR IP 2000 system is an affordable easy to use all in one recording and management solution for network surveillance systems of up to 16 channels All channels are pre licensed Running the full Bosch recording solution including the Video Streaming Gateway to integrate 3rd party cameras DIVAR IP 2000 is an intelligent IP storage device that provides both a professional video recording solution and ease of operation DIVAR IP 2000 is a 4 bay mini tower unit that combines advanced management and state of the art recording management into a single cost effective plug and play IP recording appliance for IT minded customers which are seeking for a state of the art second generation NVR recording solution DIVAR IP 2000 utilizes a highly energy efficient embedded design at a very affordable price which nevertheless boasts Bosch quality through and through Easy to install and operate DIVAR IP 2000 features wizard based set up and centralized configuration to reduce installation times All components are pre installed and pre configured Simply connect to the network and turn on the unit DIVAR IP 2000 is ready to begin recording straight out of the box DIVAR IP 2000 features front swappable SATA II hard drives providing up to 8 TB of gr
13. ing system This chapter is valid for DIVAR IP models that come with pre installed hard drives Empty units start into the DOM recovery menu on first start See also Recovering the unit page 23 4 1 Introduction DIVAR IP systems are shipped with a pre installed Configuration Wizard from factory 4 2 Setup instruction All DIVAR IP systems are preconfigured with a default IP address and with default iSCSI settings IP Address 192 168 0 200 Subnet mask 255 255 255 0 Observe the following DIVAR IP needs to have an active network link during installation Make sure that the network switch you are connecting to is powered on The default IP address must not be occupied by any other device in the network Determine whether the initial installation is on a DHCP network If not then you must assign valid IP addresses to the video devices Consult the local IT administrator to obtain a valid IP address range to be used with DIVAR IP and associated devices The default iSCSI settings are optimized for use with VRM User with administrator rights User BVRAdmin Password WSS4Bosch Notice We strongly recommended not changing the user settings Changing the user settings can result in malfunctioning of the system 4 3 Starting the application DIVAR IP system is ready to go out of the box The application provides a simple to install and intuitive to use solution for network surveillance systems To start the applic
14. ont cover 4 LANactivity LED 2 Power on off LED 5 System status LED 3 Hard disk access LED 6 Individual hard disk LED 2013 09 V2 DOC Installation Manual Bosch Sicherheitssysteme GmbH DIVAR IP 2000 Rear view I 060000000000 0000600000600 System overview en 9 1 1x eSATA for data export Note Do not connect hard disk drives for recording 4 2xUSB3 0 Note Do not use these ports for keyboard and mouse connection 2 1x Ethernet RJ45 5 1x VGA monitor 3 2x USB 2 0 Note Use these ports for keyboard and mouse connection 6 Mains connection 100 240 VAC 2 3 1 LED description front panel This chapter describes the LED displays on the front of the chassis LED indicator LED color LED state Description Power LED N A Off Power off Blue On default Working SO state HDD LED N A Off No disk access Blue Blinking Disk access LAN LED N A Off Network disconnected Blue On Network connected Blue Blinking Network activity Bosch Sicherheitssysteme GmbH Installation Manual 2013 09 V2 DOC 10 en System overview 2 3 2 DIVAR IP 2000 LED indicator LED color LED state Description System LED N A Off Power off Blue On default System has booted in normal operation Blue Blinking System is booting or shutting down Red On Critical e
15. or each recording profile select your preferred mode from the list and set the quality To modify the ecorder schedule click a profile button and move the mouse along the schedule with the left mouse button held down lag De 300 6 00 9 00 12 00 1500 18 00 2100 Monday CHEN o Do DI Do EKD I 0 DI DI DI To DI DI DI DI I I I DI DO CEO I ET m Network Tuesday 000 000 000 000 000 000 000 000 000 000 000 000 000 000 000 000 000 000 000 C 000 A A DoD Wednesday k M HY Do A DI A E E A E A A A A EA A E C KERN EET lay Date and Time Thursday 000 000 000 000 000 000 000 000 000 000 000 000 000 000 000 000 000 000 000 000 000 000 000 DOD Friday f n To uo ao a o a a a o oo ooo o oog ooo oog oog ooo ooo oog ooo oo oog ooo og ky Video Quality Saturday res onafeosforafonafesofonafeoa orafonaferefonafesaforaforaforifonafeonforafenafri ons inn 11i Sunday Current time 00 00 00 Selected time 00 00 00 00 00 00 ummar i J y E Night Eontinuous gt I i i i _ Weekend Continuous v 9 i i Low quality High quality lt Back Cancel This page allows you to define the recording profiles gt Click Next gt to continue Bosch Sicherheitssysteme GmbH Installation Manual 2013 09 V2 DOC 22 en System setup first steps Summary page DIVAR IP 2000 Configuration Wizard raya apap App Device Selection z teh La Summary Below you find a summary of all settings Please click
16. oss storage capacity All system software is pre installed and pre activated creating an out of the box ready to use video recording appliance DIVAR IP 2000 utilizes Windows Storage Server 2008 R2 operating system Chassis features The chassis includes the following features CPU Intel Atom processor 4 slots for SATA drives front replaceable 1x VGA output onboard 2x USB 2 0 2x USB 3 0 x internal USB Transcoder device 1x Gigabit Ethernet LAN port Chassis components This chapter describes the most common components included with your chassis Chassis The chassis includes 4 slots for hard drives Backplane The backplane accepts front swappable SATA II hard drives providing up to 8 TB of gross storage capacity Warning Use caution when servicing and working around the backplane Hazardous voltage or energy is present on the backplane when the system is operating Do not touch the backplane with any metal objects and make sure no ribbon cables touch the backplane 2 2 3 Power supply The chassis features a highly energy efficient power supplies Bosch Sicherheitssysteme GmbH Installation Manual 2013 09 V2 DOC 8 en System overview DIVAR IP 2000 2 3 Device views There are several LEDs on the front and rear of the chassis The LEDs show the over all status of the system and the activity and health of specific components Front view BOSCH 1 Lock for fr
17. parately from household waste In the EU separate collecting systems are already in place for used electrical and electronic products Please dispose of these devices at your local communal waste collection point or at a recycling center 1 2 Electrical safety precautions Basic electrical safety precautions should be followed to protect you from harm and the system from damage Be aware of the locations of the power on off switch on the chassis as well as the room s emergency power off switch disconnection switch or electrical outlet If an electrical accident occurs you can then quickly remove power from the system Do not work alone when working with high voltage components Power should always be disconnected from the system when removing or installing main system components such as the motherboard or memory modules When disconnecting power you should first turn off the system and then unplug the power cords from all the power supply modules in the system When working around exposed electrical circuits another person who is familiar with the power off controls should be nearby to switch off the power if necessary Use only one hand when working with powered on electrical equipment This is to avoid making a complete circuit which will cause electrical shock Use extreme caution when using metal tools which can easily damage any electrical components or circuit boards they come into contact with The power supply power
18. the drive carrier This extends the drive carrier handle 3 Use the handle to pull the drive carrier with the drive out of the chassis 4 Insert the drive carrier with the new drive into the chassis bay making sure that the drive carrier handle is completely closed Notice Except for short periods of time do not operate the unit with the hard drives removed from the bays 3 2 Installing a hard drive The drives are mounted in drive carriers To install a hard drive to the hard drive carrier 1 Remove the drive from the carrier 2 Install a new drive into the carrier with the printed circuit board side facing down so that the mounting holes align with those in the carrier 3 Replace the drive carrier into the chassis bay making sure that the drive carrier handle is completely closed Notice We recommend using the respective Bosch hard disk drives The hard disk drives as one of the critical component are carefully selected by Bosch based on available failure rates HDD not delivered from Bosch are not supported Information on supported HDDs can be found in the datasheet in the Bosch Online Product Catalog Bosch Sicherheitssysteme GmbH Installation Manual 2013 09 V2 DOC 12 en System setup first steps DIVAR IP 2000 4 System setup first steps The following installation directive provides information on Installation and Configuration DIVAR IP systems are based on Windows Storage Server 2008 R2 operat
19. the process Notice Do not turn off the unit during the process This will damage the Recovery media 3 The unit starts from the Recovery media If the setup is successfull press Yes to restart the system 4 Windows performs the initial setup of the operating system The unit restarts after Windows has completed the setup 5 After the restart of the unit the factory default settings are installed and the Windows logon screen is displayed The factory default settings are IP address 192 168 0 200 Subnet mask 255 255 255 0 User BVRAdmin Password WSS4Bosch Bosch Sicherheitssysteme GmbH Installation Manual 2013 09 V2 DOC 24 en Additional documentation and client software DIVAR IP 2000 6 Additional documentation and client software Documentation for Bosch Security System products can be found as follows gt www boschsecurity com gt select your region and your country gt select Product Catalog gt start a search for your product gt select the product in the search results to show the existing documents And on the following network share lt IP address of DIVAR IP gt sources 2013 09 V2 DOC Installation Manual Bosch Sicherheitssysteme GmbH Bosch Sicherheitssysteme GmbH Robert Bosch Ring 5 85630 Grasbrunn Germany www boschsecurity com Bosch Sicherheitssysteme GmbH 2013
20. vent occurred such as degraded RAID volume Bosch also provides the API and then application program is able to control this status Individual hard N A Off default Hard drive not present diek LED Blue On Hard drive present Red On Bosch provides the API to let application program to control this status LAN port LED description rear panel This chapter describes the LAN port LED on the rear of the chassis LAN connector Nr LED indicator LED color LED state NIC state 1 RJ45 LED N A Off No connection or 10 Mb s left Green On 100 Mb s Yellow On 1000 Mb s 2 RJ45 LED Yellow On Active connection right Yellow Blinking Transmit or receive activity 2013 09 V2 DOC Installation Manual Bosch Sicherheitssysteme GmbH DIVAR IP 2000 3 Chassis setup and maintenance en 11 Chassis setup and maintenance This chapter covers the steps required to install components and perform maintenance on the chassis Caution Review the warnings and precautions listed in the manual before setting up or servicing this chassis See also Safety precautions page 4 3 1 Removing hard drive trays The drives are mounted in drive carriers to simplify their installation and removal from the chassis These carriers also help promote proper airflow for the drive bays To remove hard drive trays from the chassis 1 Turnoff the system 2 Press the release button on
21. ware version Granted VRM 3 0 38 3 29 Unknown lt Back Next gt This page displays recorder information Click Next gt to continue 2013 09 v2 DOC Installation Manual Bosch Sicherheitssysteme GmbH DIVAR IP 2000 System setup first steps en 17 Device Selection page Configuration Wizard Passwords Device Selection R d Devices with default IP address are marked with a check Devices that are allocated to a recorder are ecorder marked with a green check box If you deselect allocated devices allocation to the recorder is removed and corresponding recordings are deleted All devices marked with a check will be configured If you notice that devices are missing in the list please click Update Tr __ Device Type MAC Address IP Address Information Na O S VIPX1600 M4 0 00 07 5F 71 338B 192 168 0 1 DHCP ni D amp vipxt xF 70 71 BC FE SA 86 160 10 90 134 O S VIPKIXF 70 71 BC FE SA S1 160 10 90 145 Date and Time O S FLEXIDOME outdoor 5000 HD 00 07 5F 78 27 99 160 10 39 35 C amp Generic BLUNK 70 71 BC FE 54 8C 160 10 90 140 O S vIPX1 xF 70 71 BC FE 5A 7E 160 10 90 126 Video Quality O amp Dinion HD 1080p 00 04 63 3F 19 46 160 10 50 84 D S nec 255P 2C 27 D7 FE 32 2D 160 10 50 45 O vipxixF 70 71 BC FE 54 80 160 10 90 128 Recording O VIPKIXF 70 71 BC FE SA 7F 160 10 90 127 O S FLEXIDOME comer 9000 MP 00 07 5F 07 02 71 160 10 39 45 sf g gaada g Summar y I
Download Pdf Manuals
Related Search