VIZIO E221-A1 22" Full HD Black LED TV
Contents
1. Connect component or composite device REAR PANEL Note The image shown above is for illustrative purposes only and may be subject to change The actual number of ports and their locations may vary depending on the model POWER INPUT Hold to turn TV off or on Tap to change input source SIDE PANEL REMOTE SENSOR amp POWER INDICATOR When using the remote aim it directly at this sensor FRONT PANEL REMOTE CONTROL INPUT Change the currently displayed input EXIT Close the on screen menu OK Select the highlighted menu option BACK Go to the previous on screen menu VOLUME UP DOWN Increase or decrease loudness of the audio MUTE Turn the audio off or on NUMBER PAD Manually enter a channel WIDE Switch the display mode POWER Turn TV on or off MENU Display the on screen menu ARROW Navigate the on screen menu GUID Display the info window V BUTTON Open the USB photo viewer CHANNEL UP DOWN Change the channel LAST Return to the channel last viewed DASH Use with number pad to manually enter a digital sub channel For example 18 4 or 18 5 REMOTE CONTROL Replacing the Batteries 1 Remove the battery cover 2 Insert two batteries into the remote control Make sure that the and symbols on the batteries match the and symbols inside the battery compartment 3 Replace the battery cover 10 CONNECTING A DEVICE Yo2. SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE THIS WARRANTY IS SUBJECT TO CHANGE WITHOUT NOTICE CHECK WWW VIZIO COM FOR THE MOST CURRENT VERSION Personal Data lf your VIZIO product is capable of storing personal data and other information ALL CONTENTS AND INFORMATION WILL BE DELETED IN THE COURSE OF SOME IN HOME AND ALL SHIP IN WARANTY SERVICE If this occurs your product will be restored to you configured as originally purchased You will be responsible for restoring all applicable data and passwords Recovery and reinstallation of user data is not covered under this Limited Warranty In order to protect your personal information VIZIO recommends that you always clear all personal information from the unit before it is serviced regardless of the servicer Zero Bright Pixel Defect Guarantee This policy covers zero bright pixel defects for the duration of the limited ONE YEAR WARRANTY on select new product purchases To determine if this guarantee applies to your product refer to the DETAILS tab of the model s product information page www VIZIO com or look for the zero bright pixel guarantee on the box Legal amp Compliance FCC Class B Radio Interference Statement NOTE This equipment has been tested and found to comply with the limits for a Class B digital device pursuant
3. Technical Problems e And More Phone 877 878 4946 TOLL FREE Email techsupport VIZlIO com Web www VIZIO com support Hours of operation Monday Friday 5 AM TO 9 PM PST Saturday Sunday 8 AM TO 4 PM PST e Se habla Espanol Nous parlons Fran ais The TV displays No Signal Press the INPUT button on the remote control to select a different input source If you are using cable TV satellite or antenna connected directly to the TV scan for channels See on page 30 There is no power Ensure the TV is plugged into a working electrical outlet Ensure the power cable is securely attached to the TV Press the Power Standby button on the remote or on the side of the TV to turn the TV on The power is on but there is no image on the screen Ensure all cables are securely attached to the TV Ensure all devices are connected correctly Devices differ see your device s user manual for details Adjust Brightness Contrast or Backlight See on page 23 Press the INPUT button on the remote to select a different input source 42 There is no sound Press Volume Up on the remote control Press the MUTE button on the remote to ensure mute is off Check the audio settings See on page 24 Ensure the speakers are set to On Ensure no headphones are connected to the TV Check the audio connections of external devices Blu ray player game console cable satellite box that are connected to the
4. highlight the content type you want to adjust and press OK USA TV USA television program broadcasts USA Movie USA movie broadcasts CAN English Canadian English television program broadcasts CAN French Canadian French television program broadcasts 2 For each rating type you want to block or unblock use the Up Down and Left Right Arrow buttons on the remote to highlight the rating type and press OK 3 When the rating type is blocked the Lock icon appears locked Content with this rating cannot be viewed 4 When the rating type is unblocked the Lock icon appears unlocked Content with this rating can be viewed If you want to block all unrated content highlight Block Unrated Shows and use the Arrow buttons on the remote to select On 5 When you are finished adjusting the rating level blocks press the EXIT button on the remote 32 1 5 From the Parental Controls menu highlight Change PIN and press OK The Change PIN menu is displayed In the New Pin field use the Number Pad on the remote to enter your new 4 digit parental control passcode In the Confirm Pin field use the Number Pad on the remote to re enter your new 4 digit parental control passcode Write down your new parental control passcode and save it in a secure location Press the EXIT button on the remote Resetting the Content Locks To reset the content locks to the factory default settings I From the Parent
5. Menu Language and press OK The Menu Language menu is displayed 4 Highlight your preferred language English French or Spanish and press OK 5 Press the EXIT button on the remote 33 Your TV can display the on screen menu in different languages To change the on screen menu language VIZIO Manu Language English French Spanish Setting the Time Zone To ensure the correct time is displayed when you press the INFO button set the TV s time zone To have the TV display the correct time you must be A connected to the internet via an Ethernet cable or a wireless network 1 Press the MENU button on the remote The on screen menu is VIZIO in displayed 2 Use the Arrow buttons on the Le T remote to highlight the Settings sedla icon and press OK The Settings nawal US menu is displayed Pacific US CAN Mountain US CAN 3 Use the Arrow buttons on the Central US CAN remote to highlight Time amp Local Settings and press OK The Time amp Local Settings menu Eastern US CAN Atlantic CAN is displayed Newfoundland CAN Indiana US 4 Highlight Time Zone and press Arizona US OK The Time Zone menu is displayed 5 Highlight your time zone and press OK 6 Highlight Daylight Savings and press OK The Daylight Savings k mw x menu is displayed Choose On 2 Vv if daylight savings is in effect or Off if it is not 7 Highlight Postal Code Enter your ZIP code using the keypa
6. TV If you are using an antenna the signal strength of the channel may be low Ensure your antenna is connected securely to the TV and move the antenna around the room or close to a window for the best signal The colors on the TV don t look right Adust the Color and Tint settings in the Picture menu See on page 20 Reset the picture settings See on page 23 Check all cables to ensure they are securely attached The buttons on the remote aren t working Ensure you are only pressing one button at a time Point the remote directly at the TV when pressing a button Replace the remote batteries with new ones See Replacing the Batteries on page 9 The image quality is not good For the best image quality view high definition programs using digital sources Connect your devices with HDMI cables If you are using an antenna the signal strength of the channel may be low Ensure your antenna is connected securely to the TV and move the antenna around the room or close to a window for the best signal The picture is distorted Nearby electrical devices may be interfering with the TV Separate the TV from electrical appliances cars or flourescent lights Ensure all cables are securely attached The display image does not cover the entire screen If you are in RGB mode computer ensure that H Size and V Position in the on screen menu are set correctly If you are using TV AV1 AV2 or Component with 480i input
7. When moving your TV from an area of low temperature to an area of high temperature condensation may form in the housing Wait before turning on your TV to avoid causing fire electric shock or component damage A distance of at least three feet should be maintained between your TV and any heat source such as a radiator heater oven amplifier etc Do not install your TV close to smoke Operating your TV close to smoke or moisture may cause fire or electric shock Slots and openings in the back and bottom of the cabinet are provided for ventilation To ensure reliable operation of your TV and to protect it from overheating be sure these openings are not blocked or covered Do not place your TV in a bookcase or cabinet unless proper ventilation is provided Never push any object into the slots and openings on your TV cabinet Do not place any objects on the top of your TV Doing so could short circuit parts causing a fire or electric shock Never spill liquids on your TV Your TV should be operated only from the type of power source indicated on the label If you are not sure of the type of power supplied to your home consult your dealer or local power company Do not apply pressure or throw objects at your TV This may compromise the integrity of the display The manufacturer s warranty does not cover user abuse or improper installations The power cord must be replaced when using different voltage than the voltage specified Fo
8. a dark room Game mode optimizes the picture settings for displaying game console output Vivid mode sets the picture settings to values that produce a brighter more vivid picture 21 Football Golf Basketball and Baseball modes optimize the picture settings for their respective sports Also try these modes for other sports Custom picture mode allows you to manually change each of the picture settings Backlight Adjusts the LED brightness to affect the overall brilliance of the picture Brightness Adjusts the black level of the picture When this setting is too low the picture may be too dark to distinguish details When this setting is too high the picture may appear faded or washed out Contrast Adjusts the white level of the picture When this setting is too high the picture may appear dark When this setting is too low the picture may appear faded or washed out If the setting is too high or too low detail may be difficult to distinguish in dark or bright areas of the picture Color Adjusts the intensity of the picture colors Tint Adjusts the hue of the picture This setting is useful in adjusting the flesh tones in the picture If flesh appears too orange reduce the level of color before adjusting tint Sharpness Adjusts the edge sharpness of picture elements It can be used to sharpen non HD high definition content however it will not produce detail that does not otherwise exist Adjusti
9. of the white areas of the picture To adjust the color temperature 1 From the Picture Settings Menu use the Arrow buttons to VIZIO A highlight More then press OK 2 Use the Arrow buttons on Color Temperature the remote to highlight Color Color Temperature Normal Temperature then press OK Red Gain 128 displeved Temperature menu is ae Ge Blue Gai EE 128 3 Use the Arrow buttons on Se ice the remote to highlight Color a TE Temperature then use the Ren E Left Right Arrow buttons to Bve Gisa 128 change the color temperature Reset Color Temperature preset e Cool produces a blue hued picture e Computer optimizes the picture for use as a PC monitor e Normal is optimized for television viewing e Custom allows you to x O yX manually change each of the color temperature settings Red Green Blue Gain Adjusts the amount of each color in the display Red Green Blue Offset Adjusts the position of each color in the display 4 If you want to reset the color temperatures to the factory default settings highlight Reset Color Temperature and press OK 5 When you have finished adjusting the color temperature press the EXIT button on the remote 23 Adjusting the Picture Size and Position When displaying an image from the HDMI input the size and position of the display image can be adjusted To adjust the picture size and position 1 Ensure the input is set to ATV HDMI or RGB VIZIO
10. or via phone at 877 MY VIZIO 877 698 4946 from 6 00AM to 9 00PM Monday through Friday and 8 00AM to 4 00PM Saturday and Sunday Pacific Time or visit www VIZIO com PRE AUTHOR IZATION MUST BE OBTAINED BEFORE SENDING ANY PRODUCT TO A VIZIO SERVICE CENTER Proof of purchase in the form of a purchase receipt or copy thereof is required to show that a Product is within the warranty period Parts and Labor There will be no charge for parts or labor during the warranty period Replacement parts and Products may be new or recertified at VIZIO s option and sole discretion Replacement parts and Products are warranted for the remaining portion of the original warranty or for ninety 90 days from warranty service or replacement whichever is greater Type of Service Defective Products must be sent to a VIZIO service center to obtain warranty service VIZIO is not responsible for transportation costs to the service center but VIZIO will cover return shipping to the customer PRE AUTHORIZATION IS REQUIRED BEFORE SENDING ANY PRODUCT TO A VIZIO SERVICE CENTER FOR WARRANTY SERVICE Product returns to VIZIO s service centers must utilize either the original carton box and shipping material or packaging that affords an equal degree of protection VIZIO Technical Support will provide instructions for packing and shipping the covered Product to the VIZIO service center Limitations and Exclusions VIZIO s one year limited warranty only covers defect
11. screen black bars are added to the left and right of the display image press OK The Input Source e Wide stretches a 4 3 aspect ratio picture to the edges Selection menu is displayed of the screen Since the picture is being stretched the display image may appear distorted If the program 4 Use the Up Down Arrow is already formatted for widescreen viewing 1 85 1 or buttons on the remote to 2 35 1 then black bars will appear on the top and highlight the input source you bottom of the display image i a a a e Zoom expands images with black bars to fit the screen e Panoramic expands the display image to fill the screen x Ow _x__4 Images may appear wider than intended If you are watching widescreen 1 85 1 or 2 35 1 content black bars will still appear on the top and bottom of the display image This option is only available when the TV is displaying a 480i 480p source e Stretch expands the display image to fill the screen Images may appear wider than intended If you are watching widescreen 1 85 1 or 2 35 1 content black bars will still appear on the top and bottom of the display image This option is only available when the TV is displaying a 720p 1080i 1080p source 18 SETTING UP CLOSED CAPTIONING Your TV can display closed captions for programs that include them Closed captions display a transcription of a program s dialogue WZ If the program you are viewing is not being broadcast AJ with closed captions t
12. shock do not touch the connector with wet hands Insert batteries in accordance with instructions Incorrect polarities may cause the batteries to leak which can damage the remote control or injure the operator Do not expose batteries to excessive heat such as sunshine fire or the like If any of the following occurs contact the dealer The power cord fails or frays Liquid sprays or any object drops into your TV Your TV is exposed to rain or other moisture Your TV is dropped or damaged in any way The performance of your TV changes substantially This apparatus shall not be exposed to dripping or splashing and no objects fill with liquids such as vases shall be placed on the apparatus The mains plug or appliance coupler is used as the disconnect device the disconnect device shall remain readily operable CAUTION These servicing instructions are for use by qualified service personnel only To reduce the risk of electric shock do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated DANGEROUS VOLTAGE within the product s enclosure that may be of sufficient magnitude to constitute a risk of electrical shock to persons TELEVISION ANTENNA CONNECTION PROTECTION If an outside antenna satellite dish or cable system is
13. 2 From the Picture Settings menu use the Arrow buttons on the Size amp Position remote to highlight More then Horiz Position press OK Vertical Position Horizontal Size 3 Use the Arrow buttons on the remote to highlight Size amp Position then press OK The Size amp Position menu is displayed Vertical Size 4 Use the Arrow buttons to highlight the setting you wish to adjust then press Left Right Arrow to change the setting e Horiz Position Adjusts the horizontal left right position of the display image e Vertical Position Adjusts Ow x the vertical up down position of the display image e Horizontal Size Adjusts the width of the display image e Vertical Size Adjusts the height of the display image 5 When you have finished adjusting the color temperature press the EXIT button on the remote Resetting the Picture Settings To reset the picture settings to the factory default settings 1 From the Picture Settings menu use the Arrow buttons to highlight More then press OK 2 Use the Arrow buttons on the remote to highlight Reset Picture Mode then press OK The TV displays Are you sure you want to RESET Picture Settings to the factory defaults 3 Highlight Yes and press OK 4 Press the EXIT button on the remote 24 ADJUSTING THE AUDIO SETTINGS To adjust the audio settings I Press the MENU button on the remote The on screen menu is VIZIO display
14. Controls and COMMNECTIONS es en 6 Front PAM RS AR ts 8 Remote COMORES R te A 9 Replacing the BAN TN SS Sn au 10 Connecting Your Devices 11 Connecting A Device Le LA nes 11 Connecting a Device Audio and Video Cable Types 12 Connecting an Audio Device sursaut 13 Connecting an Audio Device Audio Cable Types s 14 Connecting an Audio Device ARC 15 Without HDMI ARG sianie nn 15 With AMIS enero i 15 Completing the First Time Setup 16 Using the On Screen Menu 17 Navigating the On Screen Menu 17 CHANGING the Input Source sieren 18 Changing the Screen Aspect ROMO eccrine 18 Setting Up Closed CAptionNINg 228 4 eee 19 Changing the Appearance of Digital Closed Captions 19 Activating the Sleep TWN sain ce scdeanaceveiawndennsivieixndeantaiasedeance 20 Setting the Auto Power Off Feature 20 Adjusting the Picture Settings eneen 21 Adjusting the Advanced Picture Settings 22 Adjusting the Color Temperature eeiteeeteeeeeteeees 29 Adjusting the Picture Size and Position eee 23 Resetting the Picture Settings errereen 24 Adjusting the Audio Settings eeen 25 Adjusting the Advanced Audio Settings 26 Resetting the Audio Settings 26 Changing the TY SSMOSese ns unies 27 Changing the INPUT SOUE 27 Setting the Tuner Mode 28 Scanning for CM NMN IS un ae noise 28 Adding New Channels sssccncicivascecs ctbeteasueencrasub
15. E HDMI technology transmits crystal clear digital multi channel surround audio through a single HDMI cable Audio Return Channel enabled ARC TVs allow audio to be sent over an already connected HDMI cable eliminating the need for a separate audio cable See Connecting an Audio Device ARC on page 15 e CFC 2 way Communication Auto setup e PCM DTS Dolby Digital e 2 0 5 1 Scaleable Lossless Digital Audio Connection e Audio and Video Signals HDMI BEST CONNECTING AN AUDIO DEVICE ARC With HDMI ARC Without HDMI ARC Without an HDMI ARC setup your TV will transmit audio signal from the built in tuner and VIA apps to your home audio receiver through a separate audio connection 3 5MM Audio T Built in Tuner Your TV Your Blu Ray Player 15 Built in Tuner Your TV Your Blu Ray Player With an HDMIARC setup the audio connection between your TV and Home Audio Receiver can be removed The HDMI cable will transmit audio signal to and from your TV with an all digital audio video connection The first time you turn on the TV the Setup App will guide you 4 Use the OK and Arrow Up through each of the steps necessary to get your TV ready for use Down buttons on the remote to highlight your time zone and Before you begin the first time setup press OK Your TV should be installed and the power cord should be connected to an electrical outlet Your dev
16. IZIO product at www VIZIO com Complete and mail the enclosed registration card Extended Warranties For peace of mind and to protect your investment beyond the standard warranty VIZIO offers on site extended warranty service plans These plans provide additional coverage during the standard warranty period TO purchase an extended warranty service plan visit www VIZIO com WHEN READING THIS MANUAL When you see this symbol please read the A accompanying important warning or notice It is intended to alert you to the presence of important operating instructions When you see this symbol please read the AYS accompanying helpful tip IMPORTANT SAFETY INSTRUCTIONS Your TV is designed and manufactured to operate within defined design limits Misuse may result in electric shock or fire To prevent your TV from being damaged the following instructions should be observed for the installation use and maintenance of your TV Read the following safety instructions before operating your TV Keep these instructions in a safe place for future reference To reduce the risk of electric shock or component damage switch off the power before connecting other components to your TV Read these instructions Keep these instructions Heed all warnings Follow all instructions Do not use this apparatus near water Clean only with dry cloth Do not block any ventilation openings Install in accordance with the manufacturer s instruct
17. Press the MENU button on the remote The on screen menu is displayed 2 Use the Arrow buttons on the remote to highlight the Settings icon and press OK The Settings menu is displayed 3 Highlight Power Indicator and press OK 4 Use the Up Down Arrow buttons to select On or Off then press OK 35 You can use the TV s Help menu to Display system information VIZIO Reset the TV settings A Restore the TV to its factory lt Help default settings System Info Start Setup Wizard Sse Seiinge Clear Memory Factory Default Start Setup Wizard Displaying System Information To display a summary of the TV settings 5 Press the MENU button on the remote The on screen menu is displayed Use the Arrow buttons on the remote to highlight the Help icon and press OK The Help menu is displayed Highlight System Info and press OK Use the Up Down Arrow buttons to scroll through the system information When you are finished reviewing the system information press the EXIT button on the remote 36 Resetting the TV Settings To reset the TV s picture and audio settings E Press the MENU button on the remote The on screen menu is displayed Use the Arrow buttons on the remote to highlight the Help icon and press OK The Help menu is displayed Highlight Reset TV Settings and press OK The TV displays Are you sure you would like to Restore Defaults This will erase any custom settings Highlight Yes and pres
18. VIZIO USER MANUAL Model E221 A1 SfS StudioSound HD Sf S TruVolume SRS StudioSound HD and SRS TruVolume are trademarks of SRS Labs Inc StudioSound HD and TruVolume technologies are incorporated under license from SRS Labs Inc ENERGY STAR This product qualifies for ENERGY STAR in the factory default setting and this is the setting in which power savings will be achieved Changing the factory default picture settings or enabling other features will increase power consumption that could exceed the limits necessary to qualify for ENERGY STAR rating Q DOLBY DIGITAL PLUS Manufactured under license from Dolby Laboratories Dolby and the double D symbol are trademarks of Dolby Laboratories HOM HIGH DEFINITION MULTIMEDIA INTERFACE HDMI the HDMI logo and High Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC Welcome THANK YOU FOR CHOOSING VIZIO And congratulations on your new VIZIO HDTV To get the most out of your new VIZIO product read these instructions before using your product and retain them for future reference Be sure to inspect the package contents to ensure there are no missing or damaged parts PRODUCT REGISTRATION To purchase or inquire about accessories and installation services for your VIZIO product visit our website at www VIZIO com or call toll free at 877 878 4946 We recommend thot you either Register your V
19. al Controls menu highlight RESET LOCKS and press OK The TV displays Are you sure you want to RESET ALL LOCKS SETTINGS to the factory defaults Highlight Yes and press OK Changing the On Screen Menu Language Changing the Names of the Inputs To make it easier to recognize the different devices attached to the inputs on your TV you can rename the inputs For example if you have a DVD player connected to the Component input you can rename that input to display DVD Player To change the name of an input T Press the MENU button on the remote The on screen menu is displayed Use the Arrow buttons on the remote to e the Settings icon and press OK The Settings menu is displayed Use the Arrow buttons on the remote to highlight Name Input and press OK The Name Input menu is displayed Highlight Input Source and press OK Highlight the input a want to rename and press K If you would like to use a preset input label highlight Input Labels and press OK Highlight the input label you want to use and press OK When you have finished naming your input press the EXIT button on the remote 1 Press the MENU button on the remote The on screen menu is displayed VIZIO a 2 Use the Arrow buttons on the Name Input remote to highlight the Settings Input Source TV icon and press OK The Settings Input Labels SG menu is displayed D 3 Use the Arrow buttons on the remote to highlight
20. and vizio QUICK START GUIDE Moder EMTIMAT Quick Start Guide 2 x Rubber Feet Ss f Remote Control Power Cord 2 x Phillips Screws with Batteries PACKAGE CONTENTS After removing the TV from the box and inspecting the package contents you can begin installing the TV Your TV can be installed in two ways On a flat surface using the included stand On a wall using a VESA standard wall mount not included INSTALLING THE TV Installing the TV Stand Your TV includes a stand designed to support the weight of the TV and keep it from falling over However the TV can still fall over if It is placed on an uneven unstable or non level surface It is Pushed pulled or otherwise improperly moved If an earthquake occurs and the TV is not properly secured TV ON STAND To install the base 1 Place the TV screen down on a clean flat surface To prevent 2 Insert and tighten the two 2 included Phillips screws into scratches or damage to the screen place the TV on a soft the base with a Phillips screwdriver Not included surface such as a blanket Gently push the base into the slots as shown Installing the TV on a Wall To mount your TV on a wall you will need a wall mount Consult the information below to find the appropriate mount for your TV model s Installing a TV on a wall require
21. ays X You can display your photos in fullscreen Select the photo press OK then highlight Fullscreen and press OK Connected Sources Displays connected USB devices To change source highlight it and press OK Current Folder Start Fullscreen Slideshow Sort by Name View Thumbnails List View Folder Settings Back Button Highlight this button and press OK if you would like to return to the previous screen Back Button Highlight and press OK to return to left column Current Folder Displays the folder path ce Photo ed sort C Name AZ View Thumbnails File Name D 1920x1080 Resolution 1920x1080 Size 1607270KB Photo Infomation Displays name resolution and file size for currently selected photo VIZIO_2GB Photo root Wa i Hjpg Page 1 of 1 Page Information If your USB thumb drive has more fles than can be displayed on a single screen you can move between pages by highlighting this area and pressing Left Right Arrow 40 Folder Contents This area displays the contents of the currently selected folder You can browse between files using the Arrow and OK buttons on the remote PHOTO VIEWER Troubleshooting amp Technical Support A DO YOU HAVE QUESTIONS LET US HELP YOUR PRODUCT INCLUDES FREE LIFETIME TECH SUPPORT The VIZIO support team is highly trained and is based in the United States We can help with e New Product Setup Connecting Your Devices
22. berressestnecees 29 SkipPING Chine sue ie en an a 30 Changing the Audio Languge sxershiersheles e 30 Using the Parental CONS sen rien 31 Accessing the Parental Controls Menu 3 Enabling or Disabling Program Ratings 32 Locking and Unlocking Channels ass utiicesesitivaciens 32 Blocking and Unblocking Content by Rating 32 Changing the Parental Control Passcode 33 Resetting the Content LOCKS 33 Changing the Names of the Inputs sise 33 Changing the On Screen Menu Language 34 Setting the Time Zone insu x 34 Adjusting the CEC S MIngs assises 35 Turning the Power Indicator Light On or Off 35 Using the Help M DIAS eds net 36 Displaying System INfOrMOtION ccecce 36 Resettino the TV Settings raoran E E E 37 Restoring the TV to Factory Default Settings 37 Performing a Service Check 37 Using the Info WINGOW nas nt eh i 38 Using the USB Media Player 39 Using the USB M dia PIO YOM oic cccc esscesantrenenivteientcertnstesccaices 39 Connecting a USB Thumb Drive to the TV 39 Playing USB IV SOW eere 39 Troubleshooting amp Technical SUpport 4 SSC CONOMNS ES ea denses 44 Limited WCUIMOUATY oa Saisies sonssenemestesssonstesse 46 Legal amp Compliance e 47 2 INSPECTING THE PACKAGE CONTENTS Before installing your new TV take a moment to inspect the package contents Use the images below to ensure nothing is missing or damaged VIZIO LED HDTV with St
23. ble or disable the Program Rating feature 1 From the Parental Controls menu highlight Rating Enable and press OK The Rating Enable menu is displayed 2 Select On or Off and press OK Locking and Unlocking Channels When a channel is locked it will be inaccessible Locking a channel is a good way to prevent children from viewing inappropriate material To lock or unlock a channel 1 From the Parental Controls menu highlight Channel Locks and press OK The Channel Locks menu is displayed 2 Highlight the channel you want to lock or unlock and press OK 3 When a channel is locked the Lock icon appears locked The channel is not accessible unless the parental passcode is entered 4 When a channel is unlocked the Lock icon appears unlocked The channel is accessible Changing the Parental Control Passcode If you use the parental controls you should change the passcode to prevent children from accessing inappropriate material Blocking and Unblocking Content by Rating A channel may sometimes broadcast programs that are meant for children and at other times broadcast programs that are meant for mature audiences You may not want to block the channel completely using a channel lock but you may wish to block certain programs from being viewed 7 Fora list of content ratings and their definitions visit www tvguidelines org AN fie To block or unblock content by its rating 1 From the Parental Controls menu
24. d on the remote then press OK The ZIP code information is often used by VIA Apps to give you the most accurate location based information such as weather or news 8 Press the EXIT button on the remote 34 Adjusting the CEC Settings The CEC function on your TV enables you to control HDMI connected devices with the included remote without any additional programming Not all HDMI devices support CEC See your device s user manual for details To enable disable or adjust CEC settings 1 Press the MENU button on the remote The on screen menu is displayed 2 Use the Arrow buttons on the remote to highlight the Settings icon and press OK The Settings menu is displayed 3 Use the Arrow buttons on the remote to highlight CEC Settings and press OK The CEC Settings menu is displayed 4 Use the Arrow and OK buttons to adjust each setting e CEC Function To use CEC you must select Enable e System Audio Control When system audio control is on you can control your device s audio using the TV s remote control e Device Discovery Use this function to determine if your device is connected and supports CEC 5 Press the EXIT button on the remote USING THE HELP MENU Turning the Power Indicator Light On or Off The Power Indicator Light on the front of your TV is set to light up when the TV is on You can change this setting if you prefer the light to be off To turn the Power Indicator Light on or off 1
25. ed Audio Settings Use the Arrow buttons on the Balance 0 remote to highlight Audio and Lip Sync o press OK The Audio Settings TV Speakers Off menu is displayed SRS StudioSound HD Surround SRS TruVolume On Use the Arrow buttons to Meee highlight the setting you wish to adjust then press Left Right Arrow to change the setting e Balance Adjusts the loudness of the audio output from the left and right speakers e Lip Sync Adjusts the syn chronization between the display image and the accompanying audio track e TV Speakers Turns the built in speakers on or off e SRS StudioSound HD StudioSound HD is a feature rich surround sound solution which delivers an immersive surround sound experience from the TV s internal speakers Additionally StudioSound HD completes the entertainment experience by maintaining a steady volume while watching programming and movies providing deep rich bass and delivering crisp details and clear intelligible dialog Select Surround or Standard Equalizer Settings Reset Audio Mode k ow X e SRS TruVolume TruVolume intelligently normalizes volume fluctuations due to television commercials or channel changes Select On or Off 25 Advanced Audio See Adjusting the Advanced Audio Settings on page 26 Equalizer Settings Adjusts the boost or attenuation of different frequencies This setting is only available when SRS TruSurround HD is set to Off Change the eq
26. eo Signals 00000 Pr Cr Pb Cb Y BETTER l2 HDMI CABLE HDMI is the intelligent all digital interface that delivers both dazzling quality and unmatched ease of use HDMI technology transmits crystal clear digital video along with multi channel surround audio HDMI connected devices have the ability to automatically adjust themselves for optimal viewing e HD Video Resolutions up to 1080P e HD Audio e Digital Connection e Audio and Video Signals HDMI BEST CONNECTING AN AUDIO DEVICE Your TV can output sound to an audio device such as a receiver amp PRES or sound bar cn Ts 1 Verify that your device has a video port that matches an available port on the TV HDMI 3 5mm etc Home Audio Receiver 2 Turn the TV and your audio device off 3 Connect the appropriate cable not included to the TV and the device 4 Turn the TV and your device on VIZIO Sound Bar HDMI CABLE CFC 2 WAY COMMUNICATION 2 0 5 1 DIGITAL AUDIO B E ST PCM DTS DOLY DIGITAL 3 5MM CABLE ANALOG STEREO CONNECTION GOO D 2 0 CHANNEL 13 CONNECTING AN AUDIO DEVICE AUDIO CABLE TYPES 3 5MM CABLE AV cables or Composite cables are the traditional way of connecting your devices to your audio device Audio signals are sent over the 3 5mm connector e Quality Stereo Connection e 2 0 Channel e Analog Connection e Audio Signal Only O 3 5mm GOOD 14 HDMI CABL
27. he TV will not display them To activate or deactivate closed captions 1 Press the MENU button on the VIZIO remote The on screen menu is displayed Closed Caption 2 Use the Arrow buttons on the Analog Closed Caption Off remote to do Li 2 Digital Closed Caption Off icon and press A osed Digital CC Style As Broadcaster Caption menu is displayed 3 Use the Arrow buttons on the remote to highlight the type of closed captions you wish to see e Analog Closed Caption for analog NTSC TV channels e Digital Closed Caption for digital ATSC TV channels 4 After highlighting the type of closed captions you wish to see use the Left Right Arrow buttons on the remote to select the caption channel you wish to display then press EXIT x ow x Caption channels usually display different languages A For example CC1 may display English captions and CC2 may display Spanish captions S ly NS CT 19 Changing the Appearance of Digital Closed Captions Digital closed captions can be displayed according to your preference To change the appearance of digital closed captions 1 From the Closed Caption VIZIO menu use the Arrow buttons to highlight Digital CC Style 2 Use the Left Right Arrow buttons on fhe remote fo select Text Size Custom then press OK The Color Digital CC Style Caption Style Custom As Broadcast As Broadcast Digital CC Style menu appears Opacity As Broadca
28. he Timer G 2 Highlight Off or 10 min and press OK Press Exit remote to highlight the Sleep Auto Power Off Off Timer icon and press OK The Sleep Timer menu is displayed 3 Use the Up Down Arrow buttons on the remote to highlight Timer and press OK The Timers menu is displayed 4 Use the Up Down Arrow buttons on the remote to highlight the period of time after which you want the TV to turn off 30 60 90 120 or 180 minutes 5 Press OK then press EXIT ow x 20 ADJUSTING THE PICTURE SETTINGS Your TV display can be adjusted to suit your preferences and viewing conditions To adjust the picture settings Press the MENU button on the 1e highlight Picture and press OK remote The on screen menu is Zag displayed Picture Settings Use the Arrow buttons on the Picture Mode Custom remote to highlight the Picture Backlight 50 icon and press OK The Picture Brightness 50 Settings menu is displayed Contrast 50 Color E 2 50 Use the Up Down Arrow ar buttons on fhe remote to Sh arpness 0 The Picture Settings menu is displayed Use the Arrow buttons on the remote to highlight Picture Mode then use the Left Right Arrow buttons to change the picture mode Standard mode sets the various picture settings to values that will produce the best picture in the most cases This is the recommended setting Movie mode sets the picture settings to values perfect for watching a movie in
29. ices should be connected 5 Use the OK and Arrow Up Down Buttons on the remote to turn daylight saving time On or Off To complete the first time setup 1 Press the Power Standby button on the remote The TV powers on and the Setup App starts 6 Answer the on screen questions about your TV connection using the Arrow and OK buttons on the remote 2 Use the Up Down Arrow buttons on the remote to highlight your preferred language and press OK 7 Use the Arrow buttons to highlight Start the Channel 3 Use the OK and Arrow Up Scan and press OK Down buttons on the remote to highlight Home Mode and press OK 8 When you have finished the channel scan highlight Exit to Live TV and press OK The First Time Setup is complete 16 Using the On Screen Menu 5 Your TV features an easy to use on screen menu NAVIGATING THE ON SCREEN MENU To open the on screen menu press the MENU button on the remote You can also open the on screen menu by pressing the VIA button and selecting HDTV Settings from the VIA Dock then To open the on screen menu press the MENU OK button on the pressing OK remote From this menu you can Use the Arrow buttons to highlight fi a menu option and press the Change the input source VIZIO MENU OK button to select that Change the screen aspect option ratio Set up closed captioning cs X Activate the sleep timer IE Wise ce Adjust the picture settings A gt Sv Wh
30. ile navigating the on screen menu you can press Adiust the audio settinas D 5 the BACK button at any time to return to the previous g sleep pict ne menu screen The EXIT button will close the on screen Access USB photo slideshow T Ra AS menu Change TV settings Fi Access the help menu CM 02 Media Settings Help 17 CHANGING THE INPUT SOURCE CHANGING THE SCREEN ASPECT RATIO External devices such as DVD players Blu Ray Players and video The TV can display images in four different modes Wide Zoom game consoles can be connected to your TV To use one of these Normal and Stretch Each mode displays the picture differently devices with your TV you must first change the input source in the on screen menu To change the screen aspect ratio To change the input device l B MENU button on the Screen Mode remote 1 Press the MENU button on the remote The on screen menu is VIZIO a 2 Use the Arrow buttons to ee displayed highlight the Wide icon Press Input Source Selection OK 2 Use the Arrow buttons on the TV remote to highlight the Settings vi 3 Use the Arrow buttons to highlight your desired screen mode icon and press OK The TV Component and press OK Settings menu is displayed HDMI Normal preserves the content s original aspect ratio RGB Since the 4 3 aspect ratio is not large enough to fill the 3 Use the Up Down Arrow buttons on the remote to highlight the input source and TV s
31. ions Do not install near any heat sources such as radiators heat registers stoves or other apparatus including amplifiers that produce heat Do not defeat the safety purpose of the polarized or grounding type plug A polarized plug has two blades with one wider than the other A grounding type plug has two blades and a third grounding prong The wide blade or the third prong are provided for your safety If the provided plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet Protect the power cord from being walked on or pinched particularly at plugs convenience receptacles and the point where they exit from the apparatus Only use attachments accessories specified by the manufacturer Use only with the cart stand tripod bracket or table specified by the manufacturer or sold with the apparatus When a cart is used use caution when moving the cart apparatus combination to avoid injury from tip over Unplug this apparatus during lightning storms or when unused for long periods of time Refer all servicing to qualified service personnel Servicing is required when the apparatus has been damaged in any way such as when the power supply cord or plug is damaged liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped Unplug the power cord before cleaning your TV
32. iver s Holiday Surprise Ch 50 123 ACT DIV CABLE Oliver wakes up One morning only to discover that his pals are missing In this hour long holiday special Oliver goes on a journey in search of his pals Who knows what he ll encounter on the way Program Description DIGITAL EPISODE GUIDE amp INFO WINDOW 38 Using the USB Media Player 6 Playing USB Media USING THE USB MEDIA PLAYER The USB Media Player allows you to connect a USB thumb drive to your TV and view photos AUDIOOUT USB PORT Connecting a USB Thumb Drive to the TV l Turn the TV off Connect your USB thumb drive to the USB port on the back of the TV Press the Power Standby button on the remote or touch the Power control on the side of the TV to turn it on Do not remove the USB thumb drive while the TV is on Doing so may damage the drive 39 To play USB media you must first save your images onto a USB thumb drive Remember The USB thumb drive must be formatted as FAT32 Files on the USB thumb drive must end in the jpg extension To play your USB media l Connect your USB thumb drive to the USB port on the side of the TV Highlight the Media App and press OK The Media App launches Highlight your USB device in the list and press OK Highlight the type of media you wish to display Photo Press OK Use the Arrow buttons to highlight the file you want to display Press OK The file pl
33. ng the Advanced Picture Settings e Backlight Control Select Off DCR Dynamic Contrast Ratio or OPC 4 When you have finished adjusting the Advanced Picture To adjust the advanced picture settings 1 From the Picture Settings menu use the Arrow buttons on the VIZIO Z Settings press the EXIT button on the remote remote to highlight More then press OK Advanced Picture Noise Reduction Low 2 Use the Arrow buttons on the MPEG NR ER remote to highlight Advanced EE era Picture then press OK The pete Ne Advanced Picture menu is alin Mede as displayed Backlight Control OPC 3 Use the Arrow buttons to highlight the setting you wish to adjust then press Left Right Arrow to change the setting Noise Reduction Diminishes artifacts in the image caused by the digitizing of image motion content Select Off Low Medium or High e MPEG NR Reduces pixellation and distortion for mpeg files Select Off Low Middle or High e Color Enhancement Reduces oversaturation of some colors and improves flesh tones Select Off Normal Rich Color Green Flesh or Green Blue e Adaptive Luma Adjusts the average brightness of the picture to compensate for large areas of brightness Select Off Low Medium Strong or Extend e Film Mode Optimizes the picture for watching film Select Auto or Off 22 Adjusting the Color Temperature Adjusting the color temperature will change the warmness or coolness
34. ning or removing the back cover may expose you to high voltages electric shock and other hazards If repair is required contact your dealer and refer all servicing to qualified service personnel WARNING Keep your TV away from moisture Do not expose your TV to rain or moisture If water penetrates into your TV unplug the power cord and contact your dealer Continuous use in this case may result in fire or electric shock Do not use your TV if any abnormality occurs If any smoke or odor becomes apparent unplug the power cord and contact your dealer immediately Do not try to repair your TV yourself Avoid using dropped or damaged appliances If your TV is dropped and the housing is damaged the internal components may function abnormally Unplug the power cord immediately and contact your dealer for repair Continued use of yourTV may cause fire or electric shock Do not install your TV in an area with heavy dust or high humidity Operating your TV in environments with heavy dust or high humidity may cause fire or electric shock Follow instructions for moving your TV Ensure that the power cord and any other cables are unplugged before moving your TV When unplugging your TV hold the AC DC power adapter not the cord Pulling on the power cord may damage the wires inside the cord and cause fire or electric shock When your TV will not be used for an extended period of time unplug the power cord To reduce risk of electric
35. on page 18 Screen Size Viewable Area Dimensions w Stand w o Stand Weight w Stand w o Stand TV Type Refresh Rate Maximum Resolution Pixel Pitch Response Time Brightness Viewing Angle HDMI Inputs Component Video Inputs Composite Inputs RF Antenna Input USB 2 0 Ports Audio Outputs Specifications B E221 A1 ASS CLS 21 53 LUS SIM CRSO A 2S YO 1 787 6 83 lbs 6 28 lbs LED 60 Hz 1920 x 1080 248 mm x 248 mm 5 ms 250 nits 170 D 160 0A 1 Shared with Component 3 5mm Cable 44 E221 Al OSD Language English Spanish French Remote Control Model XRTO20 CSA CSA US FCC Class B Certifications HDMI 1 4 Dolby digital Plus Compliance Energy Star Voltage Range 120V 60 Hz Power Consumption 25 8W Standby Power lt 1W Zero Bright Pixel Guarantee Yes A5 Limited Warranty ON PARTS AND LABOR Covers units purchased as new in United States and Puerto Rico Only VIZIO provides a warranty to the original purchaser of a new Product against defects in materials and workmanship for a period of one 1 year of non commercial usage and ninety 90 days of commercial use If a Product covered by this warranty is determined to be defective within the warranty period VIZIO will either repair or replace the Product at its sole option and discretion To obtain warranty service contact VIZIO Technical Support via e mail TechSupport VIZIO com
36. press the WIDE button on the remote to change the screen mode The TV has pixels dots that are always dark or always lit Your HDTV is precision manufactured using an extremely high level of technology However sometimes pixels may not display correctly These types of occurences are inherent to this type of product and do not constitute a defective product A3 see When When noise or static on the screen When your TV s digital capabilities exceed a digital broadcast signal the signal is up converted improved to match your TV s display capabilities This up converting can sometimes cause irregularities in the image If you are using an antenna the signal strength of the channel may be low Ensure your antenna is connected securely to the TV and move the antenna around the room or close to a window for the best signal change input source the volume changes The TV remembers the volume level on each input source If the volume level on the new input source is higher or lower than the level on the source you switch from the difference may be noticable Use the Volume Up Down buttons on the remote to adjust the volume change input source the display image changes size The TV remembers the viewing mode on each input source If the viewing mode on the new input source differs from the one on the input source you switch from the difference may be noticable See Changing the Screen Aspect Ratio
37. r Mode Changing the Input Source To change the input source from the Settings menu l Press the MENU button on the remote The on screen menu is displayed Use the Arrow buttons on the remote to highlight the Settings icon and press OK The Settings menu is displayed Highlight Input Source and press OK The Input Source menu is displayed Highlight the input source you want to display and press OK 2 If you are using a device that is connected to the RF input such as an external antenna or cable TV connection you must set the tuner mode l Press the MENU button on the remote The on screen menu is displayed Use the Arrow buttons on the remote to highlight the Settings icon and press OK The Settings menu is displayed Highlight Tuner and press OK The Tuner Mode menu is displayed Highlight Antenna or Cable and press OK Press the EXIT button on the remote Scanning for Channels Before the TV can detect and display channels and their associated information you must scan for channels A channel scan may also be necessary when the TV has been moved to an area where different free to air broadcast television channels are available 1 From the Tuner Settings menu highlight Auto Channel Scan VIZIO A The auto channel scan begins Channel Scan 2 Wait until the channel scan is Channels touna 100 complete Highlight Done Digital 0 and press OK Analog 19 3 Press the EXIT button on
38. r more information contact your dealer Your TV is equipped with a three pronged grounded plug a plug with a third grounding pin This plug will fit only into a grounded power outlet This is a safety feature If your outlet does not accommodate the three pronged have an electrician install the correct outlet or use an adapter to ground your TV safely Do not defeat the safety purpose of the grounded plug When connected to a power outlet power is always flowing into your TV To totally disconnect power unplug the power cord The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of un isolated dangerous voltage within the inside of your TV that may be of sufficient magnitude to constitute a risk of electric shock to persons Do not overload power strips and extension cords Overloading can result in fire or electric shock The wall socket should be installed near your TV and easily accessible Only power of the marked voltage can be used for your TV Any other voltage than the specified voltage may cause fire or electric shock Do not touch the power cord during lightning To avoid electric shock avoid handling the power cord during electrical storms Unplug your TV during a lightning storm or when it will not be used for long period of time This will protect your TV from damage due to power surges Do not attempt to repair or service your TV yourself Ope
39. s OK Press the EXIT button on the remote Restoring the TV to Factory Default Settings All of the on screen menu settings can be reset to the factory defaults A If you restore the TV to the factory default settings all changes you have made to the settings will be lost To restore the TV to its factory default settings 1 Press the MENU button on the remote The on screen menu is displayed 2 Use the Arrow buttons on the remote to highlight the Help icon and press OK The Help menu is displayed 3 Highlight Clear Memory Factory Default and press OK 4 Enter your parental control passcode If you have not yet set up a parental passcode enter the default 0000 The TV displays Are you sure you would like to Restore Defaults This will erase any custom settings 5 Highlight Yes and press OK The TV displays Memory is being cleared The TV will reset shortly 6 Wait for the TV to turn off The TV will turn back on shortly afterward and the Setup App will begin 37 USING THE INFO WINDOW The Info Window can be displayed by pressing the INFO or GUIDE button on the remote Press the INFO or GUIDE button one time to display channel and input information Press the INFO or GUIDE button two times to display the program title and closed captioning information Press the INFO or GUIDE button three times to display the program description Program Title CC Information Channel Input Information Ol
40. s in materials and workmanship This warranty does not cover for example cosmetic damage normal wear and tear improper operation improper voltage supply or power surges signal issues damages from shipping acts of God any type of customer misuse modifications or adjustments as well as installation and set up issues or any repairs attempted by anyone 46 otherthan by aVIZIO authorized service center Products with unreadable or removed serial numbers or requiring routine maintenance are not covered This one year limited warranty does not cover Products sold AS IS FACTORY RECERTIFIED or by a non authorized reseller THERE ARE NO EXPRESS WARRANTIES OTHER THAN THOSE LISTED OR DESCRIBED ABOVE ANY IMPLIED WARRANTIES INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE SHALL BE LIMITED IN DURATION TO THE PERIOD OF TIME SET FORTH ABOVE VIZIO S TOTAL LIABILITY FOR ANY AND ALL LOSSES AND DAMAGES RESULTING FROM ANY CAUSE WHATSOEVER INCLUDING VIZIO S NEGLIGENCE ALLEGED DAMAGE OR DEFECTIVE GOODS WHETHER SUCH DEFECTS ARE DISCOVERABLE OR LATENT SHALL IN NO EVENT EXCEED THE PURCHASE PRICE OF THE PRODUCT VIZIO SHALL NOT BE RESPONSIBLE FOR LOSS OF USE LOSS OF INFORMATION OR DATA COMMERCIAL LOSS LOST REVENUE OR LOST PROFITS OR OTHER INCIDENTAL OR CONSEQUENTIAL DAMAGES SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS OR THE EXCLUSION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES
41. s lifting To prevent JS injury or damage to the TV ask someone to help you E221 Al Screw Pitch Screw Length Hole Pattern 100mm V x 100mm H Be sure the mount you choose is capable of supporting the weight of the TV After you have determined that you have the correct mount for your TV you can begin the installation To install yovur TV on a wall 1 Disconnect any cables connected to your TV 2 Place the TV face down on a clean flat stable surface Be sure the surface is clear of debris that can scratch or damage the TV ee you are finished place the TV on a stable level 3 Remove the base by loosening and removing the screws surface 3 Insert the two 2 included rubber feet over the screws as shown and press firmly to secure them 4 Attach yourTV and wall mount to the wall carefully following the instructions that came with your mount Use only with a UL listed wall mount bracket rated for the weight load of this TV See Appendix A Specifications for the weight of this TV Oxo ali ce i me ale Mm Oxo alal lvevile at HDMI Connect HDMI device e PC Audio In Connect 3 5mm audio cable from PC RGB Connect VGA cable from PC Coaxial Connect coaxial cable from cable satellite or antenna 0 Stereo Audio Out Connect 3 5mm audio device such as sound bar USB Connect USB thumb drive to view photo Component Composite
42. st BG Color As Broadcast 3 Use the Up Down Arrow BG Opacity As Broadcast buttons on the remote to Window Color As Broadcast z P 5 In highlight the setting you wish Window Opacity As Broadcast to change then use the Left Right Arrow buttons to change the setting e Caption Style Choose Auto to keep default settings or Custom to manually change each setting e Text Size Adjust the size of the text e Color Change the color of the text X ow X e Opacity Change the transparency of the text e BG Color Change the background color e BG Opacity Change the transparency of the background e Window Color Change the edge color e Window Opacity Change the edge type 4 When you are satisfied with the appearance of the closed captions press the EXIT button on the remote ACTIVATING THE SLEEP TIMER Setting the Auto Power Off Feature To help save energy your TV is set by default to turn off after 10 When activated the TV s sleep timer will turn the TV off after a set minutes if no signal is being displayed on the screen This feature period of time can be deactivated To use the sleep timer To set the Auto Power Off feature 1 Press the MENU button on the VIZIO 1 From the Sleep Timer menu use the Up Down Arrow buttons remote The on screen menu is on the remote to highlight Auto Power Off and press OK The displayed Auto Power Off menu is displayed lt Sleep Timer 2 Use the Arrow buttons on t
43. st be used in order to comply with the emission limits 3 The manufacturer is not responsible for any radio or TV interference caused by unauthorized modification to this equipment It is the responsibilities of the user to correct such interference FCC warning Changes or modifications not expressly approved by the party responsible for compliance with the FCC Rules could void the user s authority to operate this equipment 47 2013 VIZIO INC ALL RIGHTS RESERVED 1301240C NC
44. st in multiple languages 2 Select your preferred language French The MTS feature only works when the program being English French or Spanish Spanish viewed is being broadcast in the language you Press OK SEC 3 Press the EXIT button on the remote To use the Analog MTS feature 1 From the Tuner Settings menu highlight Analog MTS and VIZIO A press OK The Analog MTS menu is displayed lt Analog MTS Mono 2 Select Mono Stereo or coe SAP secondary audio SAP programming Press OK 3 Press the EXIT button on the Ske ee remote 30 Using the Parental Controls The TV s parental controls allow you to prevent the TV from displaying certain channels or programs without a password Accessing the Parental Controls Menu To access the Parental Controls menu 1 Press the MENU button on the remote The on screen menu is displayed 2 Use the Arrow buttons on the remote to highlight the Settings icon and press OK The TV Settings menu is displayed 3 Use the Arrow buttons on the remote to highlight Parental Controls and press OK 4 Enter your parental passcode If you have not set a passcode enter the default 0000 The Parental Controls menu is displayed WZ ES To set a custom parental passcode see Changing the Parental Control Passcode on page 32 ie ONS 31 Enabling or Disabling Program Ratings To manage program content according to its rating you must enable the Program Rating feature To ena
45. the oo Cancel remote 28 Adding New Channels Occasionally you may need to add a new analog channel or add a new range of channels You can do this by using the Partial Channel Search and Add Analog Channel options To add a range of new channels 1 From the Tuner menu highlight Partial Channel Search The Partial Channel Search menu is displayed 2 Highlight Scan Mode and select the type of channel you are adding Analog Digital Analog or Digital 3 Highlight From Channel and enter the channel from which you want to begin the scan Use the Number Pad on the remote to enter the channel 4 Highlight To Channel and enter the channel to which you want to end the scan Use the Number Pad on the remote to enter the channel 5 Highlight Start and press OK The partial channel search begins 6 Wait until the partial channel search is 100 complete Highlight Done and press OK 7 Press the EXIT button on the remote To add a single new analog channel Skipping Channels 1 From the Tuner Settings menu sy To quickly access the Input Source menu press the highlight Add Analog Channel sd a AS INPUT button on the remote and press OK The Add Analog Channel menu is displayed Add Analog Channel PRE nee After a channel scan is completed you may find that some 2 Highlight Enter Channel and RA GRGAREI channels are too weak to watch comfortably There may also be use the Number Pad on the some channels you do not
46. to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures 1 Reorient or relocate the receiving antenna 2 Increase the separation between the equipment and receiver 3 Connect the equipment into an outlet on a circuit different from that to which the receiver is connected 4 Consult the dealer or an experienced radio TV technician for help This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Notice 1 The changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment 2 Shielded interface cables and AC power cord if any mu
47. to be connected to the TV make sure that the antenna or cable system is electrically grounded to provide some protection against voltage surges and static charges Article 810 of the National Electrical Code ANSI NFPSA 70 provides information with regard to proper grounding of the mast and supporting structure grounding of the lead in wire to an antenna discharge unit size of the grounding conductors location of antenna discharge unit connection to grounding electrodes and requirements of the grounding electrode Ground Clamp Electric Service Equipment Lightning Protection For added protection of the TV during a lightning storm or when it is left unattended or unused for long periods of time unplug the TV from the wall outlet and disconnect the antenna or cable system Power Lines Do not locate the antenna near overhead light or power circuits or where it could fall into such power lines or circuits Remember the screen of the coaxial cable is intended to be connected to earth in the building installation Antenna Lead In Wire Antenna Discharge Unit NEC Section 810 20 Grounding Conductors NEC Section 810 21 Ground Clamps eee Power Service Grounding Electrode System NEC ART 250 part H Table of Contents Installing TACT PP 3 Inspecting the Package Contents 3 SAONE TM ns en ii re 3 Installing the TV SIGN de 3 lAstaling the TV on a Wal ernis 5
48. ualizer presets by selecting Jazz Classical Pop Rock or Flat To change the equalizer settings yourself highlight EQ Mode and press OK Reset Audio Mode Restores the audio settings to the factory defaults See Resetting the Audio Settings on page 26 When you have finished adjusting the audio settings press the EXIT button on the remote Adjusting the Advanced Audio Settings CHANGING THE TV SETTINGS To adjust the advanced audio settings Using the settings menu you can 1 From the Audio Settings Menu OES Change the input source use the Arrow buttons to a VIZIO highlight Advanced Audio e Adjust the Tuner settings A then press OK The Advanced lt Audio Name the TV inputs lt Settings j j j Digital Audio Out PCM Audio menu is displayed ito g Set up parental controls mee Source TV uner 2 Use the Arrow buttons to Change the on screen eR highlight the setting you wish menu language er rer to adjust then press Left Right Set the time Menu Language English Arrow to change the setting Digital Audio Out e Adjust the CEC settings fine os Saline CEC Setti Changes the type of Adjust the Power Light ee On processing for the Optical settings output or HDMI ARC output when connected to a home theater audio system Select Off Dolby Digital or PCM 3 When you have finished adjusting the advanced audio settings press the EXIT button k ow X on the remote a er 26 Setting the Tune
49. ur TV can be used to display output from most devices 1 Verify that your device has a video port that matches an available port on the TV HDMI Component etc Turn the TV and your device off Connect the appropriate cable not included to the TV and the device Turn the TV and your device on Set the TV s input to match the connection you used HDMI Component etc Cable Satellite Box DVD Blu ray Player Game Console HDMI CABLE e DIGITAL e HD VIDEO 1080p BEST e HD AUDIO COMPONENT CABLE ANALOG BETTER HD VIDEO 1080P STEREO AUDIO AV CABLE ANALOG e VIDEO i GOOD e STEREO AUDIO Maximum Resolution wE uH E ue CONNECTING A DEVICE AUDIO AND VIDEO CABLE TYPES AV CABLE AV cables or Composite cables are the traditional way of connecting your devices to your TV Video signals are sent over the yellow connector while audio is sent over the red and white connectors e Video Resolutions up to 480i e Analog Connection e Audio and Video Signals GOOD COMPONENT CABLE Component cables are designed to carry high definition video signals along with additional audio connections Colors are delivered with color information split up three different ways over three connectors for video separated into Red Blue and Green signals and the left and right audio connectors Red and White e HD Video Resolutions up to 1080p e Analog Connection e Audio and Vid
50. want to view You can remove these remote to enter the number of channels from the TV s memory with the Skip Channel feature the channel you are adding 3 Highlight Add Channel and Channels that have been removed with the Skip press OK The TV scans for the Channel feature can still be viewed if the channel channel is entered using the Number Pad If you wish to completely block a channel from being viewed use 4 When the TV is done scanning the parental controls See on page 30 for the channel press the EXIT button on the remote To remove a channel 1 From the Tuner Settings menu highlight Skip Channel VIZIO The Skip Channel menu is KK LUN XX 0 rare Skip Channel 0 Test 0 2 For each channel you wish 0 1 Testl to remove use the Up Down O1 Test Arrow butions on the remote 0 Test 3 to highlight the channel and o2 Test4 press OK An X appears to the 03 Tests right of each channel you select 3 When you have selected all of the channels you wish to remove press the EXIT button on the remote 29 Changing the Audio Language To use the Digital MTS feature Some digital free to air and cable channels broadcast programs 1 From the Tuner Settings menu in more than one language The TV s MTS Multichannel Television highlight Digital MTS and press VIZIO a Sound feature allows you to listen to audio in your preferred OK The Digital MTS menu is language displayed lt Digital MTS English A Not all programs are broadca
Download Pdf Manuals
Related Search