3M M1500SS
Contents
1. This Class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations Cet appareil num rique de la classe B respecte toutes les exigences du R glement sur le mat riel brouilleur du Canada This device complies with Part 15 of the FCC rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation 3M Touch Systems Inc Proprietary Information 3M MicroTouch Display M1500SS User Guide 33 FCC Warning To assure continued FCC compliance the user must use grounded power supply cord and the provided shielded video interface cable with bonded ferrite cores If a BNC cable is going to be used use only a shielded 5 cable Also any unauthorized changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate this device 3M Touch Systems is not responsible for any radio or television interference caused by using other than recommended cables and connectors or by unauthorized changes or modifications to this equipment CE Conformity for Europe The device complies with the requirements of the ECC directive 89 336 EEC as amended by 92 31 EEC and 93 68 EEC Art 5 with regard to Electromagnetic compatibility and 73 23 EEC2. MicroTouch Display 150055 User Guide Read and understand all safety information contained in this document before using this product MicroTouch MicroTouc 3M 3M Touch Systems Inc Proprietary Information Documen t 19 258 Rev AG 2 3M MicroTouch Display M1500SS User Guide The information in this document is subject to change without notice No part of this document may be reproduced or transmitted in any form or by any means electronic or mechanical for any purpose without the express written permission of 3M Touch Systems Inc 3M may have patents or pending patent applications trademarks copyrights or other intellectual property rights covering subject matter in this document The furnishing of this document does not give you license to these patents trademarks copyrights or other intellectual property except as expressly provided in any written license agreement from 3M Touch Systems Inc The information provided in this document is intended as a guide only For the latest detailed engineering specifications please contact your 3M Touch Systems Inc Application Engineer 3M Touch Systems Inc is committed to continually improving product designs as a result product specifications may be subject to change without notification ROHS 2011 65 EU means that the product or part does not contain any of the substances in excess of the maximum concentration values in EU RoHS Directive 201 1 65 E
3. Cursor 15 extremely jittery or erratic Power Management Possible Solutions Review the installation procedures Are all cables connected properly After you installed touch software did you restart your PC to activate the touch driver Are the communication settings correct Is the touch sensor trying to use the COM port or IRQ of another device for example a mouse If so a hardware device conflict will result and the touch sensor will not work Calibrate the touch sensor for the current video resolution and operating system Calibrate the touch sensor for the current video resolution and operating system Open the touch sensor control panel and make sure all cursor offsets vertical edge horizontal are turned off Calibrate the touch sensor for the current video resolution and operating system Stabilize the cursor by adjusting the operating frequency of the controller using the control panel The M1500SS Display conforms to the Video Electronics Standards Association VESA Display Power Management Signaling DPMS standard To benefit from power management the display must be used in conjunction with a computer and video card that implements the VESA DPMS standard The PC automatically invokes the power management feature if you do not use the touch sensor mouse or keyboard for a user defined period of time To restore the video image simply touch the sensor press a key or move the mouse 3M Touch Syste
4. Display M1500SS User Guide Connecting the Display CAUTION You are cautioned that any change or modification to the equipment not expressly approved by the party responsible for compliance could void your authority to operate such equipment To connect the 150055 Display 1 Turn off your computer You should always turn off the computer before connecting or disconnecting any device 2 Connect one end of the video cable to the video connector on the display Connect the other end to the video card in your computer 3 Connect one end of the touch sensor cable either serial or USB to the display Connect the other end to an available port on the back of your computer If you are using a USB connection make sure you have installed the Touch Software drivers prior to connecting the touch sensor cable 4 Plug the AC DC power supply into the M1500SS Display Be sure to use the power supply included with the display Figure9 Identifying Your Display Connections Touch Sensor Power Video Connection Microphone out Line In A WARNING To avoid the risk of electric shock which could result in serious injury or death This device must be operated with the original power supply part numbers HJC HASUOSF AC Adapter STD1203 e Li Shin LSE9901B1250 CHI CH 1234 3M Touch Systems Inc Proprietary Information 3M MicroTouch Display M1500SS User Guide 19 CAUTION To
5. Arm Mounting Option The unit has a 75 mm VESA mounting pattern on the back to allow for arm mount capability Follow the manufacturer s instructions included with the mounting device to properly attach your display In order to arm mount the M1500SS Display you will need to remove the display head from the stand and yoke 3M Touch Systems Inc Proprietary Information 3M MicroTouch Display M1500SS User Guide 13 Figure 3 Disassembling the Yoke amp Base for Arm Mounting Step 1 Unlock the yoke With the unit laying face 99 down safely and securely nonabrasive surface wv 29 5 remove two screws connecting the top of the yoke rq Se P d Lift yoke and pull down to disengage tabs to remove 3 E AJ A O Step 2 Remove the bottom two screws holding the E ul hinge cover in place Remove the small hinge cover o RS d Lao scr Step 3 Remove the inner four screws holding the 9 h PL base to the display and gently remove the base Countertop Base Mounting Option Keyhole slots in the bottom of base plate enable you to secure the unit to a desktop or countertop Use standard screws in the desktop or countertop and then slide the base plate on for a secure fit Note A full size template has been included in the back of this manual for your convenience Simply tear out the template and drill directly through the hol
6. Hg and must be recycled or disposed of in accordance with local state or federal laws Check your individual state s requirements to see if specific recycling requirements exist for mercury containing products or other electronic products Refer to http www nema org lamprecycle or call 3M Touch Systems 1 866 407 6666 for further information e Dispose of the flat panel display according to applicable governmental regulations Important Notes Plug power cord into appropriate power source Plug power cord into a grounded receptacle When unplugging power supply cord pull on plug not cord Do not connect or disconnect this product during an electrical storm Install the display in a well ventilated area Always maintain adequate ventilation to protect the display from overheating and to ensure reliable and continued operation not expose this display to heat Passive heat may cause damage to the case and other parts e not install this display in areas where extreme vibrations may be generated For example nearby manufacturing equipment may produce strong vibrations The vibrations may cause the display to exhibit picture discoloration or poor video quality e Ensure that metal does not contact the touch sensor e To avoid ergonomic concerns Do not install the display in a manner or location with awkward accessibility Extended use may result in muscle tendon or fixed posture strains It is recommended you t
7. The Miscellaneous Menu contains three options Reset OSD Position and System info e Reset is used to reload all factory default parameters 050 position is used to setup the OSD menu position horizontal and vertical position 15 adjusted separately Each position item will bring up the slider window the maximum value of the sliders 15 based on the size of the OSD menu e System Info is used to provide detailed information regarding the current input resolution frequencies and firmware version Note After 45 seconds of inactivity the OSD will timeout without saving any new settings Lock Out Feature Once you have fine tuned your display you may want to restrict users from inadvertently making changes In order to do this follow this simple procedure Repeat the procedure to restore access 1 Press SELECT and then press the lt left arrow key Hold both keys for 10 seconds DO NOT RELEASE 2 Then press the right arrow key and hold all three keys together for an additional 10 seconds 3M Touch Systems Inc Proprietary Information Document 219 258 Rev AG 3M MicroTouch Display M1500SS User Guide 29 CHAPTER 4 Maintenance and Troubleshooting If you have a problem setting up or using your display you may be able to solve it yourself Before calling 3M Touch Systems try the suggested actions that are appropriate to the problems you are experiencing with the display You may also want to consult
8. if you wish you can adjust the horizontal and vertical position contrast and brightness to better suit your video card and your personal preference Refer to Chapter 3 for more information on using the on screen menu to adjust the video display 3M Touch Systems Inc Proprietary Information Document 219 258 Rev AG 22 MicroTouch Display M1500SS User Guide Installing Touch Software A MicroTouch 7 driver is required to operate your 150055 Display To enhance your touch experience refer to the MT7 Software User Guide for complete instructions These drivers and relevant technical documentation can be found on the enclosed 3M Touch Solutions CD 31197 and are also available for download from our website at www 3m com touch After the software 15 installed restart your computer to load and activate the touch sensor driver The Touch Solutions CD includes the touch sensor driver and control panel that enable your touch sensor to work with your computer When you install the CD included with your display MT7 Software will be automatically loaded on your system MT7 software provides touch sensor drivers for Windows Vista Windows XP and Windows 2000 For older systems software 1s provided on the CD select the Browse CD option to enable you to load legacy touch software for Windows NT 4 0 Windows 95 or 98 or Windows Me Because these are legacy systems make sure to install the TouchWare software before connect
9. 150055 Main Menu Options Fio Auto Bright Contrast Color Position Image Misc Config 3M Touch Systems Inc Proprietary Information Document 219 258 Rev AG 24 3M MicroTouch Display M1500SS User Guide Auto Config 7 H AUTO CONFIG 1024X768 To perform an Auto Config press the lt left arrow key once then press SELECT The Main Menu item Auto Config 1s used to adjust the configuration of the phase clock vertical and horizontal position automatically A confirmation box 15 displayed to confirm the user selection The default selection in the box 1s NO and 15 highlighted by a red bar If the Select key 15 pressed the main menu 15 redisplayed and nothing 15 changed When Yes 15 selected an automatic configuration 15 started After the process 15 completed successfully a confirmation box Does this image look correct is displayed If the image looks the way you want it to look select Yes to save this setting and exit the confirmation box If image does not look the way you want select No to go to IMAGE gt PHASE to adjust the phase manually to the best image quality Refer to that section for more details Brightness H BRIGHTNESS 69 Selecting the Brightness option will allow you to adjust the brightness of display Adjust the brightness using lt left and right arrow buttons and press SELECT to confirm the new setting 3M Touch Systems In
10. LOTL 13 Access to the V1 OC Gia NG 14 Adjusting the Viewing cesses eene nennen nennen 14 Installing the Video Card and Video eto ERE Imber aae ass 15 Configuring the Display Pe PER EVE 15 IVT ege Ssi 16 Optional Card Reader 16 S pporled Op ee 16 Connecting Display 18 Cable Management 20 Testing the MISOOSS Display eecese orn treten rtt orte rte Ph PER EHE FRE PER n VERA 21 Insralims Touch Solla 27 Chapter 3 Video Display Options Adjusting the M1500S5 Video sento odo 23 Document 219 258 3M Touch Systems Inc Proprietary Information Rev AG 4 3M MicroTouch Display M1500SS User Guide Chapter 4 Maintenance and Troubleshooting Maintaining Your Touch Display eret rastro rts tanus int ern risa crore tano 29 Touch Sensor Care amd M UE 29 Display Installation Probletfus uie coerente terrent reinen ara ra dedu 30 Troubleshooting the Touch Sensor 31 Power INN i O ronde RES nar RESE Mera a UAE 31 Regulatory Agency Approva
11. PHASE CLOCK Use lt left and right arrow buttons to scroll through the image menu Phase If the phase of your display is not fine tuned you may observe unstable horizontal noise lines and cross talk stretching from the edge of small windows on your display If you change your display to Windows shut down mode this noise will be more visible and easier to eliminate Click on the Start button at the bottom right side and then click Shut Down This will bring you to the Windows shutdown mode After finishing phase adjustment click on the Cancel to return to your original Windows display Clock If the clock setting of your image 15 not fine tuned you may observe periodic vertical bars of video noise on your image These bars of noise are usually adjusted out when an Auto Configuration is performed If the bars of noise are still present this setting can be adjusted manually Adjust this setting so that either the vertical bars of noise are replaced by an even amount of noise across the whole screen or the noise disappears completely If you do an Auto Config the display will try to find the best Clock Phase setting If you are not satisfied with the auto adjustment fine tune the phase manually as described above Miscellaneous Menu 0 E MISC MENU RESET OSD POSITION SYSTEM INFO 3M Touch Systems Inc Proprietary Information 3M MicroTouch Display M1500SS User Guide 27
12. U unless the substance is in an application that is exempt under EU RoHS The MCVs are by weight in homogeneous materials This information represents 3M s knowledge and belief which may be based in whole or in part on information provided by third party suppliers to 3M NOTICE Given the variety of factors that can affect the use and performance of a 3M Touch Systems Inc Product the Product including that solid state equipment has operation characteristics different from electromechanical equipment some of which factors are uniquely within User s knowledge and control it is essential that User evaluate the 3M Touch Systems Inc Product and software to determine whether it 15 suitable for User s particular purpose and suitable for User s method of application 3M Touch Systems Inc statements engineering technical information and recommendations are provided for User s convenience but their accuracy or completeness is not warranted 3M Touch Systems Inc products and software are not specifically designed for use in medical devices as defined by United States federal law 3M Touch Systems Inc products and software should not be used in such applications without 3M Touch Systems Inc express written consent User should contact its sales representative 1f User s opportunity involves a medical device application IMPORTANT NOTICE TO PURCHASER Specifications are subject to change without notice These 3M Touch Systems Inc Products and softw
13. ake periodic breaks from continuous use Service and Repair Indicators Do not attempt to service this unit yourself Removing the display cover may expose you to dangerous voltage or other risks and will void the warranty WARNING To avoid the risk of fire which could result in serious injury or death Do not remove the cover or back of the display 3M Touch Systems Inc Proprietary Information Document 19 258 Rev AG 8 MicroTouch Display M1500SS User Guide A CAUTION To avoid the risk of electric shock which may result in minor or moderate injury Do not service the display e There are no user serviceable parts inside e Refer all servicing to qualified service personnel Do not remove the cover or back of the display Unplug the display from the power outlet and refer servicing to qualified service personnel in the event that e Liquid is spilled into the product or the product is exposed to rain or water The product does not operate properly when operating instructions are followed The product has been dropped or the case has been damaged The product shows a distinct change in performance indicating a need for service The power cable or plug is damaged or frayed 3M Touch Systems Support Services 3M Touch Systems Inc provides extensive support services through our website and technical support organization Visit the 3M Touch Systems website at http www 3m com touch where
14. are are warranted to meet their published specifications from the date of shipment and for the period stated in the specification 3M Touch Systems Inc makes no additional warranties express or implied including but not limited to any implied warranties of merchantability or fitness for a particular purpose User is responsible for determining whether the 3M Touch Systems Inc Products and software are fit for User s particular purpose and suitable for its method of production including intellectual property liability for User s application If the Product software or software media is proven not to have met 3M Touch Systems Inc warranty then 3M Touch Systems Inc sole obligation and User s and Purchaser s exclusive remedy will be at 3M Touch Systems Inc option to repair or replace that Product quantity or software media or to refund its purchase price 3M Touch Systems Inc has no obligation under 3M Touch Systems Inc warranty for any Product software or software media that has been modified or damaged through misuse accident neglect or subsequent manufacturing operations or assemblies by anyone other than 3M Touch Systems Inc 3M Touch Systems Inc shall not be liable in any action against it in any way related to the Products or software for any loss or damages whether non specified direct indirect special incidental or consequential including downtime loss of profits or goodwill regardless of the legal theory asserted Copyri
15. as amended by 93 68 EEC Art 13 with regard to Safety 3M Touch Systems Inc Proprietary Information Document 19 258 Rev AG DV Ava 85661 vum oq aseg Jo ww 66 10 1 WW OL 6 0 bununoyw 9 z o 3noqe si 6 99 51 2 ui 1011u0UJ mas snf py 12 0 uey pue ww 01 8 0 5 mas 5 25 JO s joy y up pue avens uo 5141 50291545 u no WE 9215 enpe umed A aulq n gt 6ununoy w aseg SSOOSLW uMOUS ON 9528
16. avoid the risk of electric shock which may result in minor or moderate injury The socket outlet should be installed near the equipment and should be easily accessible Use a power cable that is properly grounded Always use the appropriate AC cord certified for the individual country Some examples are listed below USA UL Switzerland SEV Canada CSA Britain BASE BS Germany VDE Japan Electric Appliance Control Act 5 Connect the power cable to the AC DC supply Connect the other end to the appropriate AC outlet Figure 10 Connecting the M1500SS Cables to your Computer You should be sure all cable connections are secure tighten all cable screws Shaking and vibration may dislodge cables that are improperly connected Route all wiring and cabling away from heat sources and sharp metal edges to avoid damage Also keep the touch sensor cable away from sources of electromagnetic and radio frequency interference WARNING To avoid the risk of electric shock which could result in serious injury or death e Do not use a damaged power supply e Do not use a power cord that is frayed or otherwise damaged 3M Touch Systems Inc Proprietary Information Document 19 258 Rev AG 20 3M MicroTouch Display 150055 User Guide Cable Management System Figure 11 Removing the Cable Management Cover 65 2303 Once you have connected your M1500SS Display to your computer you should take advantage
17. c Proprietary Information 3M MicroTouch Display M1500SS User Guide 25 Contrast el Selecting the Contrast option will allow you to adjust the contrast of the display Adjust the contrast using lt left and right arrow buttons and press SELECT to confirm the new setting Color RGB ADJUST BLACK LEVEL ADJUST AUTO CONTRAST When you choose the Color option from the OSD this will bring up a sub menu that allows you to adjust the RGB or Black Level color balance for your display Use the lt left and right arrow buttons to scroll through the color menu You can also use the Auto Contrast feature to automatically adjust the color and contrast of your display By adjusting a single color you can make the picture look warmer biased towards red or cooler biased towards blue Adjusting all three levels will make colors appear more or less striking Position A POSITION H POSITION V POSITION You can use the Position option to center the image on the display manually Use the left and P right arrow buttons to scroll through the position menu 3M Touch Systems Inc Proprietary Information Document 219 258 Rev AG 26 MicroTouch Display M1500SS User Guide e H Position is used to adjust the horizontal image position manually V Position is used to adjust the vertical image position manually Image On IMAGE
18. er Check that the video input from the video card falls within the refresh rate of the display Refer to Table 1 for details Check that your computer 15 using a supported display mode Refer to Table 1 for details Is the display in Power Management mode Touch the sensor press any key on the keyboard or move the mouse to restore operation Are the brightness and contrast settings too low Use the display controls to adjust these values Check that the video input from the video card falls within the refresh rate of the display Refer to Table 1 for details Check that the video cable 1s connected properly and securely to the display and the computer Perform an Auto Config Check that the video cable 15 connected properly and securely to the display and the computer Check that no pins are bent in the video cable connector The video display adjustments are incorrect Refer to Chapter 3 for adjusting procedures 3M Touch Systems Inc Proprietary Information 3M MicroTouch Display M1500SS User Guide 31 Troubleshooting the Touch Sensor If you are experiencing problems with the touch sensor check the following list of common installation errors Table 4 Common Sensor Installation Issues Common Installation Issues Sensor does not respond to touch Sensor 15 not accurate Cursor does not follow finger movement or does not reach the edges of the screen Cursor 1s not located directly underneath your finger
19. es indicated to secure your display to any surface Figure 4 Keyhole Mounting Slots 5 5 mm 17 75 mm 10 mm 65 2604 3M Touch Systems Inc Proprietary Information Document 219 258 Rev AG 14 MicroTouch Display M1500SS User Guide Access to the Video Controls The controls for adjusting the video display are located on the front of the 150055 Display These buttons let you display on screen menu and adjust the phase image position contrast and brightness Make sure you have unobstructed access to the video controls once the M1500SS Display is installed Refer to Chapter 3 for more details on these controls Figure 5 Video Display Controls MENU aS ea SELECT Adjusting the Viewing Angle Microphone LED The yoke and spine were designed with touch stability in mind This innovative design keeps the display face stable during touch The unit can be adjusted to any locked position from 0 up to 60 degrees from vertical This allows for users of different heights to view the display at the angle that best suits them with no degradation in touch stability Turn the positive locking mechanism adjustment knob one quarter turn horizontal to vertical to loosen Adjust the M1500SS Display by pushing on the top front of the display until the screen 15 at the best viewing angle for you Then turn the adjustment knob a 1 4 turn back to lock in place To raise the display back to vertical un
20. ght 2002 2009 3M rights reserved Document Title 3M MicroTouch Display M1500SS User Guide Document Number 19 258 Version AG 3M the 3M logo MicroTouch and the MicroTouch logo are either registered trademarks or trademarks of 3M in the United States and or other countries Windows and or other Microsoft products referenced herein are either registered trademarks or trademarks of Microsoft Corporation in the U S and or other countries other trademarks are the property of their respective owners 3M Touch Systems Inc Proprietary Information 3M MicroTouch Display M1500SS User Guide Contents Overview Important Safety Information eo oerte teen tr ean esti nane ruant bna rade n 5 Service and Repair comenta cuo EebUS OREMUS TIEN UIEAF IUUD 7 3M Touch Systems Support Services voa PERXbNE PU eER EY FRA retia dass 8 Contact 3M Touch 8 Chapter 1 Introduction to Flat Panel Displays IN EMEN 9 Native Video Resolution on a Flat Panel 10 Chapter 2 Setting Up Your 150055 Display EE TUE 11 Unpacking Your Touch Display ee eteoton pereat phot 12 Arm MONTIS gere iuam iN D pM EPI P UNI UE DN D IEEE 12 Countertop Base Mounting OD
21. ill not work with Apple Macintosh computers The requirements for your PC are as follows e Your PC must have an available RS 232 serial communication port or USB port You connect the touch sensor to this port e Your PC must have a video card and video driver already installed for the display If you need to install a video card or a video driver refer to your computer documentation for instructions Your PC must have a unique interrupt request available to the touch sensor COM port The touch sensor cannot share an IRQ with another device When choosing your workspace select a sturdy level surface Also make sure you can easily access the back of the touch display and the computer Easy access helps ensure a smooth setup of the touch display Note Before setting up your M1500SS Display refer to the Important Safety Information section at the beginning of this document 3M Touch Systems Inc Proprietary Information Document 219 258 Rev AG 12 3M MicroTouch Display 150055 User Guide Unpacking Your Touch Display Carefully unpack the carton and inspect the contents Your M1500SS Display includes the following cables as well as a touch software CD Figure 2 Cables Included with Your M1500SS um S 15 pin video cable 9 pin RS 232 serial communication cable if applicable ACIDC power supply AC power cable 12V DC output USB Cable if applicable Multimedia audio cables
22. ing the USB touch sensor cable to your system To complete the setup of your touch display make sure you calibrate the touch sensor 3M Touch Systems Inc Proprietary Information 3M MicroTouch Display M1500SS User Guide 23 CHAPTER 3 Video Display Options This chapter provides guidelines for adjusting the video display and using the display controls to adjust the image to your liking Before you make any adjustments Be sure to adjust the controls in your normal lighting conditions e Display a test image or pattern whenever you adjust the video Adjusting the M1500SS Video Display Your M1500SS Display has four controls to adjust the video display MENU Shows or hides the menu e SELECT Highlights the current menu option or saves the current setting Press or 4 to change the value e lt Left Enables you to scroll backwards through items on the menu decrease value of selected option or move to the previous menu item Enables you to scroll forward through items on the menu increase value of selected option or move to the next menu item If you do not press the Menu Select or lt left or right adjust buttons for 45 seconds the display adjustment program times out and hides the menu options You can press the Menu button at any time to display the options again Pressing MENU will pull up the On Screen Display OSD menu as shown below Figure 14
23. lay bezel and includes multimedia cables These cables can be connected from either the rear of the display or in front two separate sets of Jacks are included Figure 7 Multimedia Cables Optional Card Reader Bracket The 150055 Display 15 available with an optional card reader bracket and 2 M3 screws that supports IDTech and MagTech brand electronic card readers The black version is part number 5013923 and the beige version 15 5103924 The M1500SS has been designed with slots on either side of the bezel to accommodate this card reader bracket Simply slide the bracket into the appropriate holes and pull down slightly to lock in place Refer to the illustration below for wiring suggestions Note that 3M Touch Systems does not supply these card readers Supported MagStripe Readers At the time of publication the following mini magnetic card readers have been tested to fit the 3M Touch Systems optional card reader bracket Consult your card reader sales representative for model numbers not listed here 3M Touch Systems Inc Proprietary Information 3M MicroTouch Display M1500SS User Guide 17 Table 2 Supported MagStripe Readers all mini sized readers IDT332123 IDT33028 oo IDT332123PP _ IDT3301 33 1 Figure 8 Card Reader Mounting and Cable Management Py mp a i nd hui 65 2305 3M Touch Systems Inc Proprietary Information Document 219 258 Rev AG 18 3M MicroTouch
24. lock the adjustment knob lift slightly on the adjustment knob and pull up Figure 6 Viewing Angle Adjustable from 0 up to 60 degrees 65 2302 3M Touch Systems Inc Proprietary Information 3M MicroTouch Display M1500SS User Guide 15 Note When the adjustment knob is horizontal it is locked when it is in the vertical position it is unlocked Always maintain adequate ventilation to protect the display from overheating and to ensure reliable and continued operation Installing the Video Card and Video Driver Before you can connect your touch display make sure your computer has a video card and driver already installed for the display The video driver is supplied by the video card manufacturer and may be found on the disks that came with your computer If you need information on installing a video card or video driver refer to your computer documentation for instructions Supported Video Display Modes and Refresh Rates Your video card should support one of the display modes specified in Table 1 If you select an unsupported video mode the display may stop working or display unsatisfactory picture quality Table 1 Applicable Display Mode and Refresh Rate Display Mode Refresh Rate VGA 640 x 480 60 72 42 US Text 720 x 400 70 SVGA 800 x 600 56 Hz 60 12 75 XGA 1024 768 60 70 75 Configuring the Display Settings After you connect your 150055 Display and turn on your computer you may need to co
25. ls raar A Pu EEA 32 CE Conformity 33 3M Touch Systems Inc Proprietary Information 3M MicroTouch Display M1500SS User Guide 5 Overview Welcome to the world of 3M Touch Systems a world where using a computer is as simple as touching the sensor This guide describes how to set up your MicroTouch Display M1500SS This document assumes you have basic computer skills You should know how to use the mouse and keyboard choose commands from menus open and run application programs and save files 3M Touch Systems Inc is committed to being a premier supplier in touch systems throughout the world As a 3M Touch Systems Inc customer you are aware that we have strong internal programs that meet or exceed environmental regulations of our customers and the regions in which we conduct business Important Safety Information Read and understand all safety information before using this product Follow all instructions marked on the product and described in this document Pay close attention to the following installation warnings and safety precautions Intended Use The M1500SS Display was designed for touch input and tested to replace an existing display These displays are intended for indoor use only and are not designed for use in hazardous locations Explanation of Signal Word Consequences DANGER Indicates a potentially hazardous situation which if not avoided will result i
26. ms Inc Proprietary Information Document 219 258 Rev AG 32 3M MicroTouch Display M1500SS User Guide Regulatory Agency Approvals Your product complies with the following regulatory standards FCC B CE UL cUL CCC C tick RoHS WEEE directives This equipment has been tested and found to comply within limits for a Class B digital device pursuant to Part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference in residential installations This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there 15 no guarantee that interference will not occur in a particular installation If this equipment does cause interference to radio or television equipment reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Move the equipment away from the receiver e Consult the dealer an experienced radio television technician for additional suggestions CAUTION You are cautioned that any change or modification to the equipment not expressly approved by the party responsible for compliance could void your authority to operate such equipment
27. n death or serious injury and or property damage WARNING Indicates a potentially hazardous situation which if not avoided could result in death or serious injury and or property damage CAUTION Indicates a potentially hazardous situation which if not avoided may result in minor or moderate injury and or property damage CAUTION Indicates a potentially hazardous situation which if not avoided may result in property damage 3M Touch Systems Inc Proprietary Information Document 219 258 Rev AG 3M MicroTouch Display M1500SS User Guide DANGER To avoid the risk of fire and or explosion which will result in serious injury or death Do not install or use this product in a hazardous location WARNING To avoid the risk of fire which could result in serious injury or death Do not remove the cover or back of the display To avoid the risk of electric shock which could result in serious injury or death e This device must be operated with the original power supply part numbers HASUOSF e AC Adapter 5101203 e Li Shin LSE9901B1250 e CHI CH 1234 Do not use a damaged power supply Do not use a power cord that is frayed or otherwise damaged A CAUTION To avoid the risk of electric shock which may result in minor or moderate injury e The socket outlet should be installed near the equipment and should be easily accessible Use a power cable that 15 properly grounded Always use the appro
28. n exact number of pixels associated with it There is a one to one mapping between the number of pixels and the video resolution A flat panel display should be used at the resolution dictated by the number of pixels on the panel for optimum performance For example the 150055 Display has 1024 pixels across the screen and 768 lines of pixels down the screen and can accurately display this resolution at full screen Options for Using Other Video Resolutions The 150055 Display supports all standard resolutions up to their respective native resolution for display setup Refer to Table 1 for additional details Many video cards initially display a screen image at the SVGA or VGA resolution By supporting these resolutions the display can display the desktop controls that let you change to the optimal resolution of 1024 x 768 3M Touch Systems Inc Proprietary Information 3M MicroTouch Display M1500SS User Guide 11 2 Setting Up Your 150055 Display This chapter describes how to set up and integrate your MicroTouch M1500SS Display into a touch application system You need to complete the following tasks Unpack the components Connect the video and power cables to your computer Power on the display and test your setup Install the MT 7 software then connect the sensor cable Calibrate the touch sensor System Requirements The 150055 Display requires a personal computer PC This touch display w
29. nfigure one or more of these display settings The ideal settings for this display are as follows e Display mode also called desktop area or video resolution 1024 x 768 e Refresh rate also called vertical scan rate or vertical sync 60 Hz e Color depth also called color palette or number of colors at least 16 bit high color 3M Touch Systems Inc Proprietary Information Document 219 258 Rev AG 3M MicroTouch Display M1500SS User Guide Using the Standard Controls for the Video Card In addition to the standard controls on the display each video card has several controls that let you adjust the display settings The software and driver for each video card is unique In most cases you adjust these settings by using a program or utility provided by the manufacturer of the video card For example you can use the Windows Display Properties control panel to adjust the desktop area resolution color depth and refresh rate Whenever you change these settings or calibrate the touch sensor the image size position or shape may change This behavior is normal You can readjust the image using the display controls described in Chapter 3 of this guide For more information on adjusting the desktop area resolution color depth or refresh rate refer to your video card documentation Multimedia Features The M1500SS Display comes with multimedia features built in It has a microphone and speakers built into the back of the disp
30. of the cable management system designed into the base of the 150055 Display as shown above In order to properly route all cables through the cable management system the cover on the base unit must be removed To remove this cover 1 Push in and lift up on each of the two tabs located on the left and right sides of the cover This action will release the cover tabs from the base Figure 12 Cable Management Cover Tabs 2 Slide the cover back towards you to remove 3M Touch Systems Inc Proprietary Information 3M MicroTouch Display M1500SS User Guide 21 Figure 13 Sliding Cable Management Cover Off Base Testing the M1500SS Display Note The M1500SS Display has a power status light located on the front of the bezel After connection turn on the power switch located at the bottom of the front bezel Before you test your display make sure all cables are connected properly and routed through the cable management system Be sure to tighten all cable screws Power switch Volume Microphone in Head Phones To test that the display is working properly 1 Turn on your computer 2 Make sure the video image 15 displayed If it 1s not turn on your display Check to see that the LED on the front bezel is green orange indicates power but no signal 3 Make sure the video image 15 centered within the screen area Use the display controls to adjust the image if necessary Perform an Auto Config first then
31. ouch sensor of choice for public access applications requiring high levels of durability and reliable performance 24 hours a day 7 days a week Figure 1 M1500SS Display Adjustment Mechanism The M1500SS Display features an innovative design adjustable to approximately 60 off the vertical to accommodate different counter and user heights a positive locking mechanism a touch sensor interface several mounting options and built in cable management The M1500SS Display also features a space saving design high resolution low radiation and low power consumption These qualities make the M1500SS Display ideal for applications that require superior color resolution and clarity 3M Touch Systems Inc Proprietary Information Document 19 258 Rev AG 3M MicroTouch Display M1500SS User Guide The 150055 Display is available in a 15 diagonal screen size using active matrix thin film transistor AM TFT liquid crystal display technology The 150055 Display supports a full screen resolution of 1024 x 768 Note The M1500SS Display has a power LED as well as four buttons for using the on screen menu and adjusting the video display Refer to Chapter 3 for more information on these controls Native Video Resolution on a Flat Panel Display Flat panel displays unlike CRTs are optimized to run at one resolution A flat panel display has discrete points that determine the exact location of a pixel Each flat panel display has a
32. priate AC cord certified for the individual country Some examples are listed below USA UL Switzerland SEV Canada CSA Britain BASE BS Germany VDE Japan Electric Appliance Control Act Do not service the Display o There are no user serviceable parts inside Refer all servicing to qualified service personnel o The backlight inverter output is at high voltage Do not use non conforming replacement parts Do not place wet or damp objects on the display Do not expose the display to rain or other sources of water steam or moisture Do not place foreign objects on the display or its cables Do not remove the cover or back of the display To avoid the risk of glass breakage which may result in minor or moderate injury e Handle the display with care to avoid breaking the touch sensor The display contains glass parts Dropping the display may cause the glass parts to break Do not place foreign objects on the display 3M Touch Systems Inc Proprietary Information 3M MicroTouch Display M1500SS User Guide T CAUTION To avoid the potentially hazardous situations associated with the use of isopropyl alcohol which may result in minor or moderate injury or property damage Follow all instructions and recommendations in the manufacturer s Material Safety Data Sheet and product label To avoid possible environmental contamination which may result in minor or moderate injury e The lamp s inside this product contain mercury
33. y Information Document 19 258 Rev AG 30 3M MicroTouch Display M1500SS User Guide Always dampen the cloth and then clean the sensor Be sure to spray the cleaning liquid onto the cloth not the sensor so that drips do not seep inside the display or stain the bezel Always handle the touch sensor with care Do not pull on or stress cables Display Installation Problems Table 3 Installation Concerns Problem No image displayed blank screen Abnormal image Colors of image are abnormal Disturbances on the screen Possible Causes and Solutions Is the display receiving power Check that the computer s power cable is connected properly and securely in a grounded electrical outlet Check that the AC DC power supply is firmly plugged into the display Check that the green light appears on the bezel indicating the display 15 powered on and receiving a signal Check that the AC DC power supply cable 15 connected properly and securely to an electrical outlet Check that the LED 15 showing green on the AC DC power supply Try using another power cable Try using another electrical outlet Is the display receiving a valid video signal from the PC Check that the computer is powered on Check that the video cable 15 connected properly and securely to the display and the computer Check that no pins are bent in the video cable connector Check that the video card 1s firmly seated in the card slot in your comput
34. you can download MT 7 software and drivers obtain regularly updated technical documentation on 3M Touch Systems products and learn more about our company Whenever you contact Technical Support please provide the following information e Touch display size part number and serial number e Current driver version e Operating system used Information on additional peripherals Technical Support 15 available Monday through Friday 8 30 a m to 5 30 p m with limited call back service after 5 30 p m until 8 00 p m US Eastern Standard Time 9 a m to 5 p m throughout Europe You can contact 3M Touch Systems Inc Technical Support US only Eastern Standard Time by calling the hot line sending email or a fax e Technical Support Hot Line 978 659 9200 e Technical Support Fax 978 659 9400 e Toll Free 1 866 407 6666 Option 3 e Email US TS techsupport mmm com Contact 3M Touch Systems Contact information for all offices can be found on our website at http www 3m touch 3M Touch Systems Inc Proprietary Information 3M MicroTouch Display M1500SS User Guide 9 Overview CHAPTER 1 Introduction to Flat Panel Displays The 3M Touch Systems product line of Flat Panel Display FPD touch displays offers the M1500SS Display for desktop and countertop applications with built in multimedia options The display is available with 3M Touch System s ClearTek surface capacitive touch sensor Surface capacitive 15 the t
35. your video card user s manual for additional troubleshooting advice Maintaining Your Touch Display To maintain your display and keep your display operating at peak performance e Keep your display and touch sensor clean Adjust the display video controls Refer to Chapter 3 for more information e Do not install the display in a place where ventilation may be hindered Always maintain adequate ventilation to protect the display from overheating and to ensure reliable and continued operation Touch Sensor Care and Cleaning The touch sensor requires very little maintenance 3M Touch Systems recommends that you periodically clean the glass touch sensor surface Typically an isopropyl alcohol and water solution ratio of 50 50 is the best cleaning agent for your touch sensor You can also use straight isopropyl alcohol A CAUTION To avoid the potentially hazardous situations associated with the use of alcohol or other solvents which may result in minor or moderate injury or property damage Follow all instructions and recommendations in the manufacturer s Material Safety Data Sheet and product label Be sure to follow solvent manufacturer s precautions and directions for use when using any solvents It 15 important to avoid using any caustic chemicals on the touch sensor Do not use any vinegar based solutions e Apply the cleaner with a soft lint free cloth Avoid using gritty cloths 3M Touch Systems Inc Proprietar
Download Pdf Manuals
Related Search