ABUS Eycasa
Contents
1. Important The video door station is subject to limitations in battery mode to ensure the longest possible battery life The following functions are disabled Proximity key backlighting of the doorbell button door opener and door bell function no relay triggering continuous video transmission We recommend that you run the video door station on a permanent power supply to be able to use the full functionality 25 After connecting the power supply mount the video door station on the house wall The recommended installation height is 1 6 meters between the ground and camera module Put on the video door station at the desired location and use the screw holes on the bottom shell to mark the drill holes After finishing the wall mounting put the door station back together to complete the installation 6 3 Mounting the Eycasa outdoor camera Use the camera mount to help you find a suitable place for installation Use the drill holes to mark the surface and drill the holes Insert the included wall plugs before you attach the mount with the screws You can also swivel the mount by 90 into a particular position First loosen the screw on the side and set the required angle Then tighten the screw to secure the required position Screw the camera onto the mount and connect the power supply unit to the camera Important Only use the included antenna for installation 26 6 4 Mountin2. eee cece cece eee eeeeeeceeeeeeseeceeeseeseeeaeenees 26 6 4 Mounting the Eycasa Family Care camera ccccccceccecceeeceeeceeeseeaeeeaeeeaees 2f 6 5 Mounting the Eycasa NandSet cccccccsecceeceeeceeceeceeeceeseeecseceeeaeeseesaeeaeenaes 20 A System operatio SIM 28 1l sStart p or mie EycasamMain Uie cuo oreet tte aee RO 28 5 2 Operating ine lVe VIGW sceaccetosetiecctiotehen vtto etude Dee Ono p t rete bec ebat ebur eot ietar etel 29 1 9 Eventisbahd event DENAVIOR suscite dta a Pix mb I Eh Rie dx cu uud 31 7 3 1 Playback of event recordings ccccceccseceseeceeceeeceeeseeeeeeeeeeseeeseeseesseeeaees 32 fe SN DOOD CM GVOLIL uoatoneccatiaissccodiadnedadecxotiadaduriadatacudbno dat tau dacu quatn at an aider pud 33 1392 Proximity key eVeDlboui oui ono ioctl lento bntine tee conet hut deakd seidnedd heces be ton td i Cond 34 leoo MOIGN EVERE eicit iei sooo tuo teo ti eoe tpa EEEE eius 35 23 0 Family Care CV CI scans qas sten dot ut sa go SES ATO SR eR AREE UE MDd USE EU QuIO OR UR QUSR OE A gn deu du OF I ditas 36 7 4 General system settings ccccccecceecceeeceeeceeeeeeceseceeecaeecaeseeesaueceeeeeeeaeesseesanes 37 LANVEN ITOCK SOUNO Saee E 37 1 4 2 Software update settings ioo o o Eo a ES Eo HER te RE Eo SEL Ee IRLS ELS 38 49 Language SeLtlhigs sorron toe ideo eiae o vi cedro oai Don vaca Vae ape aod aoa Vade va Da V S v Soo te 38 7 4 4 Screen saver settings ccccccceccseeceeeceeeceee
3. Outdoor camera detects motion using the integrated PIR sensor 2 he screen on the Eycasa main unit is activated 3 The view switches from 4x view to the individual image view of the outdoor camera 4 The event message is displayed on the screen Important Event messages from external cameras are only detected in the 4x view activated by default or with the currently selected camera If the main unit is in the individual image view only the currently displayed outdoor camera can detect motion 35 7 3 5 Family care event tll S S t ri LX Sy oy Gy ruben Voice activation sequence 1 The VOX function of the Family Care camera is activated using the monitoring function on the main unit 2 The integrated voice detection function of the Family Care camera detects a sound source 3 The screen on the Eycasa main unit is activated 4 The live image of the Family Care camera is displayed 5 An audio connection to the Family Care camera is started up listening only for 30 seconds 6 The event message is displayed on the screen Possible user actions Effect Acknowledge the event message The event message is hidden o You can also press the and x buttons after the event message has been acknowledged The event message is acknowledged Press the button A lullaby is played on the Family Care camera for 90 seconds The event message is acknowledged An active voice connection to the
4. indicates the current status by the flash code on the status LED If the video door station is not paired in your Eycasa main unit the status LED flashes red The video door station housing must now be opened for the pairing process Use the included screwdriver to loosen the safety screws above the lens and below the battery compartment 17 First remove the battery compartment to be able to remove the front cover You can now continue the pairing process for your video door station The setup wizard of your main unit should show the following view Pairing 20f5 Proceeding from here will disconnect any camera currently paired in this slot Do You wish to continue A notification message will appear that a camera already paired to the selected camera slot will be overwritten by this action Press Next if you are sure you want to continue with the pairing process Pairing 3o0f5 Initialize pairing process ven front panel of your Eycasa video door station and press the pairing button for one vith a spiky tool video door station LED is blinking red green 0 1 second clock pulse Then click Nex If your video door station is running on batteries then you need to press the doorbell button once to wake up the device from standby mode Now press the pairing button on your video door station The status LED on your video door station flashes alternately red and green to indicate that the pairing process has started The pair
5. Family Care camera is PIESNE UNON established and maintained for up to 60 seconds No response An audio connection listening only to the Family Care camera is maintained for 30 seconds The video connection is ended after 30 seconds if the camera is in battery mode The event message Family Care missed is saved 36 7 4 General system settings Pressing the Cd button gives you access to the system settings Note that you can block access to the settings menu by assigning a PIN 25 11 2073 10 05 25 AM General General 3c Softwareupdate Language amp Cameras C m cq De Recordings Screen saver Audio volume er Proximity Key n yam About Eycasa You can save settings in the submenus by pressing the button Pressing this button also takes you to the higher level item in the main menu 7 4 1 PIN lock settings By assigning a 4 digit PIN you can secure your Eycasa main unit against unauthorized access to the system settings After the function is activated your PIN is requested every time the system settings are called up 0970172013 9 38 55 AM General PIN lock Show PIN Enable PIN Proximity Key Delete P Reset Repeat PIN Confirmation of the entered PIN to avoid typos Show PIN Display the PIN code during entry Enable PIN Activates the PIN lock function Information The PIN lock setting is retained even after the device is turned off or restarted If you lose Entry of a 4
6. Pairing the system components 5 1 Pairing the Eycasa components in the Eycasa main unit We recommend that you pair the video door station in the entrance area to camera position 1 factory setting with the CASA31000 All other components can be paired to any of the other camera positions Pair the components as follows Note The CASA31000 Eycasa video door station and Eycasa main unit included in delivery are already programmed at the factory Important Before you begin installing make sure that the wireless transmission range is adequate at the site of the required installation Start pairing the system components before you perform the final installation of the individual Eycasa components 1 Connect your Eycasa main unit and the components to be paired to the associated power supply unit power supply 2 Wait until your Eycasa main unit has completed the boot process and switch to the configuration menu by pressing the Cd button Click the Cameras menu item and select a free camera channel Press the Pair camera button to start the pairing process using the setup wizard 5 Inthe setup wizard select your camera model as shown in the figure Pairing Step1 p Select camera type to pair The setup steps are described below separately for each camera type 5 2 Pairing the Eycasa video door station Connect your video door stations with the power before starting the pairing process Your video door station
7. active voice connection for the video door station is established and maintained for up to 60 seconds P The event message is acknowledged and the doorbell ringing Press the button ends Press the door opener RELAY 1 on the video door station No response Doorbell ringing stops after 30 seconds Video connection is disconnected after 30 seconds unless Camera permanently active has been selected The Missed Door Bell event message is saved on the main unit 33 Possible user actions on the handset Sets up a voice connection to the door station Triggers the door opener No active voice connection is set up The call is then disconnected automatically If the button is pressed during an active voice connection this will also result in the call being disconnected Hang up reject An active voice connection can be disconnected by pressing the red button If an incoming call is not answered this button disconnects the call directly without any interaction 7 3 2 Proximity key event Sequence of the proximity application Hold the paired proximity key up to the video door station The door opener RELAY 1 on the video door station is operated The screen on the Eycasa main unit is activated The live view switches to the video door station with the activated proximity key The event message is displayed on the screen SUPE drum 34 7 3 3 Motion event Sequence of motion detection 1
8. the optional proximity key allows convenient opening of the door from outside on the video door station The Eycasa door amp house wireless video system can be expanded with additional components from the Eycasa family Eycasa outdoor cameras monitoring of driveways or gardens The system can manage a total of up to four cameras from the Eycasa product family For a detailed description of functions refer to Section 3 Features and functions 2 Eycasa system components f CASA30200 Eycasa main unit D T a CASA30500 optional Eycasa outdoor camera CASA30300 Handset optional CASA30100 CASA30150 Eycasa video door station Eycasa battery set optional CASA30400 optional Eycasa Family Care camera FUBE50020 optional Proximity key 3 Features and functions e Eycasa door amp house wireless video system for watching speaking listening and switching e The Eycasa door amp house wireless video system set contains the Eycasa video door station and Eycasa main unit e Secure wireless transmission using 2 4 GHz digital wireless for video and 1 9 GHz DECT for audio e Wireless range up to 30 meters may be less depending on structural conditions for all Eycasa system components to the main unit indoors e System expandable to include up to three additional cameras e Eycasa main unit with 7 touchscreen and built in microphone and loudspeaker e Eycasa video door station for u
9. 0970172013 94519 AM Cameras Gy Gy Gy Gy E General Camera 1 Camera 2 Camera 3 Camera 4 Cameras F Reset D Selection of the camera channels 1 4 The currently selected camera is highlighted in blue Input field for camera name with a maximum of 12 characters Choose a suitable name for your camera such as front door or backyard Display of the camera type If the No camera type appears no camera has been programmed on the currently selected channel Pair camera starts the setup wizard for new cameras See item 5 Pairing system components Video door station settings 0970172013 9 49 27 AM Cameras ia amp Gy Qy at General Camera 1 Camera 2 Camera 3 Camera 4 Name Cameras e e Proximity Key Pair camera Pad Reset 10 20 40 60 80 Selection of the doorbell tone This sound is played on the main unit during doorbell operation Setting for the door opening time RELAY 1 when the door opener is triggered by the main unit or proximity key Setting for rotation of the camera image 90 to the left or right for horizontal installation of the video door station Setting for deactivation of continuous transmission of the video image of the video door station This setting is deactivated in the factory settings in order to avoid constant monitoring When the setting is deactivated the video image of the door station is transmitted only during t
10. Deutsch English Francais Gy Cameras General I Proximity Key Nederlands Italiano Espa ol Svenska Pad Reset C Polski Upon reset or during initial start up of the main unit a system language must first be selected 38 7 4 4 Screen saver settings Select the activation time for the screen saver 02 10 2013 2 25 41 PM General Screen saver m General Shade display after minutes Gy Cameras e Recordings t4 Proximity Key F Reset The screen saver is automatically activated after the set time if during this time there has been no user input on the touchscreen and no events on the main unit The monitor dims in this mode but the system functions are still active The screen saver is automatically deactivated at any time if the touchscreen is touched anywhere or if an event occurs Important If the screensaver mode is started the Eycasa main unit will close the connection to all connected Eycasa Outdoor cameras automatically after 90 minutes Alarm messages and camera loss events will not be detected in this state After the screensaver is stopped the Eycasa outdoor cameras are available again with full functionality 7 4 5 Audio volume settings Here you set the volume of the currently selected doorbell ring tone and the touch click volume within the software 0970172013 9743 527 AM General Audio volume m General Volume ring tone Gy Cameras 0 25 te Proximit
11. LINK LED Is blinking green Click Next p Follow the instructions on the screen and press and hold the pairing button on the power cable of the camera The link LED of the camera starts to flash Now press Next without releasing the pairing button Pairing 30f3 Pairing finished Camera pairing succeeded p Once the message Camera pairing succeeded appears you can release the pairing button The pairing process is completed If an error occurs during the process repeat the previous pairing steps 5 4 Assigning the Eycasa Family Care camera Make sure that your Eycasa Family Care camera is supplied with power You can now proceed with the assignment process for your Family Care camera The setup wizard of your main unit should show the following screen 20 Pairing 3of5 Initialize pairing process Press the pairing button at your FamilyCare camera for one second The FamilyCare camera LED Is blinking red green 0 1 second clock pulse Then click Next Follow the instructions on the screen and press and hold the pairing button on the camera The Status LED on the camera starts flashing red and green Now press Next Pairing 4of5 Performing pairing The pairing of your FamilyCare Camera pairing is initialized The procedure may take a few seconds Please wait until the LED of your FamilyCare Camera is lit permanent green Your Eycasa main unit then connects to the Family Care camera The p
12. RR KK C EF M NER RED NM S 9 4 1 Description of the Eycasa main UMIt ccc ccccceeceecceeeeeeceeeseeeseeeseeeseeeseesaees 9 4 2 Description of the Eycasa video door station cccceccceecceeeeeeeeeeeeeeeeeseeees 10 4 3 Description of the Eycasa outdoor camera eseeeeseeeeneereeenne 14 4 4 Description of the Eycasa Family Care camera eeeeeeeeeseeeee 15 4 5 Description of the Eycasa NandsSet cccccccceccseeeeeeeeeeeeeeseeeseeaeeeseeseesaeess 16 5 Pairing the system components icis sivo aux ritu oia iov contu oia rei ee teu a din an conv iv u ca 17 5 1 Pairing the Eycasa components in the Eycasa main unit 17 5 2 Pairing the Eycasa video door station eseseseseeseeeereereeee 17 5 3 Pairing the Eycasa outdoor CAMELA ccccccceeceeeceeceeceeeceecaeeceeceeseueseesaeesaes 20 5 4 Assigning the Eycasa Family Care camera eeseeseeeeeeeereee 20 5 9 Pairing the Eycasa liandsel ocior reise event et ona ro su boc Soda ocv Ova vau ave eve ees 22 6 Mounting the system components eeeeeeeeeseeee rsen nennen nnn nnn 23 6 1 Mounting the Eycasa main UNIt ce ccccc eee ecceeeeeeceeeeeeseeseeeseeeeeeaeeseeeaeenaes 23 6 2 Mounting the Eycasa video door station ccccccceccecceeeseeeeeeeeeseeeseeseeeeeenees 24 6 3 Mounting the Eycasa outdoor camera
13. Security Tech Germany Eycasa Door amp House Wireless Video System User Guide Version 09 2014 C 4 English translation of the original German user guide Retain for future reference 1 Introduction Dear customer Thank you for purchasing this product This product complies with current European regulations The declaration of conformity can be obtained from ABUS Security Center GmbH amp Co KG Linker Kreuthweg 5 86444 Affing GERMANY To maintain this status and to guarantee safe operation it is your obligation to observe these operating instructions Read the entire user guide carefully before starting operation of the product and pay attention to all operating instructions and safety information All company names and product descriptions are trademarks of the corresponding owner All rights reserved In the event of questions please contact your local maintenance specialist or dealer A Warning as required by 201 StGB German Criminal Code Whosoever unlawfully makes an audio recording of the privately spoken words of another or uses or makes a recording thus produced accessible to a third party shall be liable to imprisonment or a fine Whosoever unlawfully overhears with an eavesdropping device the privately spoken words of another not intended for his attention or publicly communicates verbatim or the essential content of the privately spoken words of another recorded or overheard shall in
14. ation 24 hours standby IP34 500 g 53 Model number CASA30500 Eycasa outdoor camera Horizontal angle of view OP Range of night vision function Range SSS 3 JOl OO Degree ofprotection o IPP66 4 The wireless transmission range depends on environmental factors e g mobile communication masts high tension pylons electrical wires ceilings and walls etc If conditions are not favorable the range will be limited 54
15. bnet mask 255 255 255 D E Proximity Key Gateway 192 168 106 1 Reset DNS address 172 20 2 2 Activate automatic download for updates We recommend selecting the DHCP option for internet access NTP synchronisation If this causes problems or there is no DHCP server in the network you can configure a static IP address instead 40 Activate network Activates deactivates the network port of the Eycasa main unit DHCP If this function is activated your main unit takes its IP configuration from your router or another network device with a DHCP server Manual IP address If this function is activated you can make the IP address configuration manually IP address Enter the IP address here Make sure that the address you choose is not used by any other device In private networks the address is usually 192 168 0 XXX 255 255 255 0 usually 192 168 0 1 DNS address Enter the DNS address of your internet provider Generally this is the IP address of your router usually 192 168 0 1 Warning Only use the manual IP address settings if you know exactly which values have to be set If possible use the DCHP option The Eycasa main unit currently supports the IPv4 protocol 41 The camera settings allow you to pair new cameras in the Eycasa main unit and change the configuration Depending on the paired camera type different configuration elements are available General camera settings 7 5 Camera settings
16. ceeceseceeeceeceeeuesaueseeeseeeseeseeesanes 39 7 4 5 Audio volume settings eseesssssssssssseeseneennn nnne 39 7 45 Time and date Selllhgs seimpe ter vertais botas encode ptum EnEeD at Maru EIE 40 TE ANGI ONK CUNO Seats caress tac atge E A E S 40 1 9 Camera SeltlfitS iscceieesen senem mentem enn edt sed eee eu eese eer esa du iere 42 1 0 IRGCOFOING SEUNG Serenar anne S m UT 44 hale EODEM KOV S CHING Suoreoootoeee oot tuti retro tob mito os A obod 45 0 5etihgs on the Eycasa handset catena teta ue tenta etn blot died beet Eos 4T 1 9 Factory settings eesesssssssssssssssseseseeeenee nenne nenne nennen nnn sse nensis 49 5 Maintenance and CLEANING usce oreet eh autunno atari ait ott aate ei 50 eM MIFIT 50 80 2 CICANING MR T T MmMmTMM 50 9 DIS llietece m 50 TO TECHNIC Al Gata et ERE 51 1 Intended use The Eycasa wireless intercom system consisting of a main unit and the video door station gives you the advantage of using 2 4 GHz wireless digital radio for video data and DECT for audio data to operate your video intercom Alternatively the video door station can be operated on a permanent power supply recommended or on batteries at the front door By connecting the video door station to an electronic door opener when the doorbell is pressed the door can be opened from inside using the touchscreen of the main unit in addition to the video display and voice communication Alternatively
17. ch supply the line voltage specified on the type plate If you are unsure of the power supply at the installation location contact your power supply company Disconnect the device from the power supply before carrying out maintenance or installation work Overloading Avoid overloading electrical sockets extension cables and adapters as this can result in fires or electric shocks Liquids Make sure that no liquids of any type are able to enter the device Cleaning Only use a damp cloth to clean the device Do not use corrosive cleaning materials Disconnect the device from the power supply while doing so Accessories Only connect devices that are suitable for the intended purpose Otherwise hazardous situations or damage to the device can occur Installation position The Eycasa video door station is designed for use in protected outdoor areas The Eycasa main unit is only intended for use indoors The products may be damaged if they are dropped even from a low height Install the products so that no direct sunlight can shine on the image sensor Pay attention to the installation instructions in the corresponding section of this user guide Never place the devices close to heaters stoves other sources of heat or in direct sunlight Only operate the devices at locations where temperatures within the permitted ambient temperature range prevail 7 Wireless transmission The wireless range depends on a variety of environmental factor
18. cur the same penalty A Disclaimer This user guide has been produced with the greatest of care Should you discover any missing information or inaccuracies please let us know about them ABUS Security Center GmbH does not accept any liability for technical and typographical errors and reserves the right to make changes to the product and operating instructions at any time and without prior warning ABUS Security Center GmbH is not liable or responsible for direct or indirect damages resulting from the equipment performance and use of this product No forms of guarantee are accepted for the contents of this document Explanation of symbols The triangular warning symbol indicates important notes in this user guide which must be observed This symbol indicates special tips and notes on the operation of the unit All guarantee claims are invalid in the event of damage caused by non compliance with this user guide We cannot be held liable for resulting damage In the event of material or personal damage caused by improper operation or non compliance with the safety information we cannot be held liable All guarantee claims are void in such cases This device has been manufactured in accordance with international safety standards Please read the following safety instructions carefully Safety information 1 Power supply The power supply is 12 V DC from a power supply unit Only operate devices using power sources whi
19. current or AC DC 12 24V alternating current Terminal connector for electronic door opener 1 Potential free relay NO normally open RELAY Terminal connector for electronic door bell 2 Potential free relay NO normally open Connection for an electronic door opener Connect the electronic door opener to RELAY 1 using either a separate power supply unit version A or directly version B via the power supply of the video door station For version B take note of the permitted power supply for your door opener e A voltage that is too high can damage your door opener e lf the power consumption is too high for the switching procedure the network supply for your video door station can fail Ensure that the power supply unit for your video door station has a sufficient rating min 1A or higher Version A Version B MEE 12V 24V RELAY RELAY 12V 24V RELAY RELAY e ACIDC 2 AC DC 1 2 230V 230V 230V 12 Connection for an electronic door bell Connect the electronic door bell to RELAY 2 Before use ensure that your door bell has a suitable opening contact for triggering The door bell is supplied with power via the door bell s intended voltage source separate power supply unit or batteries When using an electromechanical door bell use the power supply via RELAY 2 so that the bell is triggered when switched by closing the circuit The function to trigger the door bell via RELAY 2 requires the software ver
20. d the outdoor camera can be accessed The following functional scope is available for manual selection on the respective devices a Door station When the door station camera is set to Camera permanently active the live image of the door station can be transmitted to the handset The door opening function is also available If the door station camera is not permanently activated then no image is transmitted to the handset Only the door opening function will be available for selection To return to the Camera list simply press the red Back button on the handset b Outdoor camera The video image from the outdoor camera can be accessed using the handset To do so simply select the required camera using the handset To return to the Camera list simply press the red Back button on the handset 48 Select Reset to reset your Eycasa main unit to the factory settings The following settings are deleted 7 9 Factory settings e All settings for doorbell tones are set to the standard settings e All camera names are deleted e he wireless connection to all connected cameras is deleted e All camera settings alarm rotation volume are deleted e he event list is deleted e The current PIN is deleted e All audio settings are reset to the standard settings e he screen saver is set to the standard settings e The proximity key is deleted from all video door stations e The remote connection to th
21. digit number on the on screen keypad your PIN a restore is possible using the SuperPIN To use the SuperPIN enter the time displayed on the device in the format HHMM H 7 hour M 7 minute as the PIN 37 7 4 2 Software update settings Here you can update the software of your Eycasa main unit using an SD card 2270372013 8 44 59 AM General Softwareupdate Name EycasaViewer General Current version 1 0 439 New version No SD Card Name EycasaLauncher Current version 1 0 436 New version No SD Card Qy Cameras Name Firmware Current version 2039 New version No SD Card E ib Proximity Key Eycasa video door station Door V1 2 0 120521 201303140 Eycasa outdoor camera Camera 2 V1 2 0 120521 Reset Eycasa outdoor camera Camera 3 V1 2 0 120521 Eycasa outdoor camera Camera 4 V1 2 0 120521 On our homepage http www abus com you can check whether a new firmware file is available for the CASA31000 Eycasa main unit The following steps must be carried out with the update 1 Download the firmware update from the ABUS homepage 2 Unzip the update to an SD card 3 Insert the SD card into main unit and start updating You can find the remaining steps in the readme file included with the download Before the update make sure your SD card is formatted as FAT32 7 4 3 Language settings Select the desired system language for your Eycasa main unit 0970172013 9 35 29 AM General Language
22. e handset is deleted After resetting of the settings the system language must be set again Note The connected video door stations must be operating on a power supply unit in order to be completely reseted 49 8 Maintenance and cleaning 8 1 Maintenance Examine the technical safety of the product regularly e g check the housing for damage If it seems that it may no longer be possible to operate the device safely stop using the product and protect it from unintentional use It is likely that safe operation is no longer possible in the event that e he device shows signs of visible damage e The device no longer works correctly For the Eycasa main unit and outdoor camera take note of the following You do not need to perform any maintenance on the product There are no components to service and there is nothing inside the product to check Never open it For the Eycasa video door station take note of the following If you operate the video door station on batteries check the state of charge at regular intervals by establishing a voice connection to the main unit If a battery message appears on the main unit you should replace them promptly 8 2 Cleaning Clean the device with a clean dry cloth The cloth can be dampened with lukewarm water if the dirt on the monitor is hard to remove A Important Only use the included antennas for installation Do not allow any liquids to enter the device Do not
23. g the Eycasa Family Care camera Bolt the camera onto the bracket and select a suitable place to mount it The camera should be mounted no further than 3 metres away from the child in order to ensure optimum visibility and reliable sound detection Important Please make sure the camera and the cable are well out of reach of your child in order to prevent the risk of strangulation Please note that if you only operate the camera with the battery it must be charged as soon as possible after the power LED starts flashing Important Note that the camera contains a built in battery which must be fully charged before the first use The status LED lights up green as soon as the battery is fully charged 2f 6 5 Mounting the Eycasa handset Wall mounting Free standing installation i 30 mm Om k i LL lt t Screw the docking station to the wall The drilling distance is 30 mm Plug the stand and the docking station together 7 System operation 7 1 Start up of the Eycasa main unit Sequence 1 Connect the power supply unit to your Eycasa main unit The device starts automatically after the line voltage is present Wait until the boot process is complete During initial start up the system language is set after the system boots Select the language by pressing the c
24. he doorbell ringing process This setting is not relevant for operation of the door station in battery mode Setting of the loudspeaker volume on the video door station Important In order to ensure legal compliance it is recommended that continuous transmission of the video image be deactivated when publicly accessible spaces can be viewed Outdoor camera settings 0970172013 39 55 31 AM Cameras 3 G i a Gy E enera Camera 1 Camera 2 Camera 3 Camera 4 Backya rd Eycasa outdoor camera Pair camera C Rotate Q e Proximity Key Cameras P Reset D Activate alarm Setting for activating deactivating the event message of the outdoor camera If the setting is not activated motion events are not evaluated Setting for rotation of the camera image 90 to the left or right in case of outdoor camera installation orientation requiring such rotation 43 Family Care camera settings 2571172013 1004 25 AM Cameras r ET M General Camera 1 Camera 2 Camera 3 Camera 4 Cameras Eycasa FamilyCare camera M C Rotate e Recordings e Proximity Key Sensitivity Volume FamilyCare camera 9 S P Reset medium 10 20 40 60 380 100 Setting the lullaby This tune is played when you press the Lullaby button on the main unit of the Family Care camera Voice detection sensitivity setting of the Family Care camera The higher the set value the more quickly the camera reacts to sounds and tr
25. iggers the VOX alarm Setting for turning the Family Care camera image 90 to the left or right if installed to do so Loudspeaker volume setting of the Family Care camera 7 6 Recording settings The recording settings menu allows you to set the recording function for your video doort station Insert an SD card at least 2 GB max 32 GB in the Eycasa main unit to save video data 02 10 2013 2 21 15 PM Recordings T B amp amp nat General T T Camera 1 Camera 2 Camera 3 Camera 4 Gy Cameras Camera 1 Eycasa video door station Recordings amp Proximity Key Clean SD Card P Reset Activates deactivates recording for the selected video door station Deletes all data on the SD card that is not relevant for Eycasa 44 You can play the recorded video data directly via the event list if the Eycasa main unit or play it on your PC The video data is saved in the eycasa videofiles folder on the SD card Important The recording function operates using the integrated circular buffer of the event list The circular buffer has a capacity of 500 entries Once this has been reached older entries and video data are overwritten Make sure that the SD card is not pulled out of the main unit while video data is being recorded or played 7 7 Proximity key settings In the Pair proximity key menu you can manage your chip keys For pairing the individual keys in addition to activation of the command wi
26. ing process is active for 120 seconds Press the Next button 18 Pairing 4o0f5 Performing pairing The pairing of your video door station Is initialized The procedure may take a few seconds Please wait for lapsing of the the video door stations LED Your Eycasa main unit connects to your video door station The process can take several seconds The setup wizard will signal whether the process is complete or whether it needs to be repeated due to a pairing error Pairing 5of5 Pairing finished Video door station was ully paired If the message Video door station was successfully paired appears the pairing process is finished The status LED goes out on your video door station signaling readiness You can proceed with installation of the unit from Chapter 6 Note If you want to test the video door station after initial start up note that there can be audio feedback loops both in the loudspeaker of the door station and the main unit if the devices are too close to each other This is normal and occurs only when both devices are installed in the same room 19 5 3 Pairing the Eycasa outdoor camera Ensure that your Eycasa outdoor camera is supplied with power You can now proceed with the pairing process for your outdoor camera The setup wizard of your main unit should show the following screen Pairing 2of3 Initialize pairing process Press and hold the pairing button on the outdoor camera The
27. nication Volume control Reduces the volume during voice communication SD card Slot for SD card for software updates and recording Supports SD cards up to 32 GB SDHC 23 Sable ment Removable table mount can be used instead of the included wall mount Power supply 12V DC 1A Device starts automatically when powered by line voltage RJ45 connection Integrated network access 10 100 Mbps Loudspeaker System loudspeaker for outputting audio 4 2 Description of the Eycasa video door station 12V 24V RELAY RELAY AC DC 2 Camera module with fixed lens including photo sensor Indicates the current device status The sequence for doorbell LED ru ub Permanent lit ringing is being carried out Voice connection has LED green Permanently lit SONA ER No wireless connection to Status LED E LED ru re the main unit or device is not paired LED et T et Flashing fast Flashing fast Pairing mode active Indicates that the device LED rA Permanent is ready to operate when voltage is present 10 Doorbell button ABUS logo Proximity Proxmiyreader Connector block Rear i Battery compartment Loudspeaker Important Backlit doorbell button not in battery mode Backlighting switches on automatically in night mode camera photo sensor When the doorbell button is pressed a connection to the Eycasa main unit is established with a video image Built in microph
28. ns Managing proximity keys Press a key from the list to select it and display the chip key management options 11 07 2013 2 48 20 PM Proximity Key No Name Door Proximity Key 2 1 Key name Key 2 dE is Proximity Key P Reset Change the chip key name Change the name of your chip key using the on screen keyboard Change the chip key status By activating deactivating the button you can change the status of the chip key If the button is deactivated the key is inactive and cannot be used to open the doors until the status is manually reset to active Use this option to temporarily block a key Delete chip key If the button is activated the selected key will be deleted completely after confirming with OK 46 7 8 Settings on the Eycasa handset amp Camera E D Direct access to components which are connected to the Eycasa main unit Open the settings for the handset Brightness Lock screen Pairing D Brightness setting for the display with the levels Low Medium and High Time setting after which the locked screen is automatically activated 10s 30s 1m 2m Audio relevant parameter settings doorbell loudspeaker VOX with the levels Low Medium and High Pairing mode menu 47 Doorphone Camera The list visible under Camera includes all devices which have been taught in and paired with the Eycasa main unit The door station an
29. o door station is designed for use in protected outdoor areas thanks to its degree of protection of IP54 In case of horizontal installation in the settings you need to change the orientation of the video image to 90 to the left or right Use the included screwdriver to loosen the safety screws above the lens and below the battery compartment If you are operating your video door station with a permanent power supply bell transformer remove the cover of the terminal connector on the rear of the device Be sure to reinstall the sealing ring later 24 You can now open the plastic cover of the doorbell button and attach your nameplate For labeling you can use the included nameplate or the PDF template on the included CD c oomm 55m Connect the power 12 24 V AC DC and an optional electronic door opener RELAY 1 and or an electronic door bell RELAY2 to the terminal block of the video door station 12V 24V RELAY RELAY AC DC 1 2 LJ i i 1 Important When operating with a permanent power supply e g bell transformer the video door station requires up to 800 mA at 12 V Make sure that downstream consumers such as electronic door openers do not exceed the total output of the voltage source If you operate the video door station alternatively using batteries insert the batteries into the battery compartment Pay attention to the polarity when inserting the AA batteries En n
30. one for two way voice communication with Eycasa main unit or handset Logo can be rotated 90 with horizontal installation of the video door station Built in proximity reader for use of the ABUS wireless chip key FUBE50020 for opening the door on the door station Not available in battery mode Connector block for power and relay contacts potential free NO Voltage 12 24 V AC DC Relay 1 door opener Relay 2 electronic chime Not available in battery mode Removable battery compartment for 6 x AA batteries 1 5 V Use CASA30150 for this Two way communication for Eycasa main unit Integrated loudspeaker The video door station is subject to limitations in battery mode to ensure the longest possible battery life The following functions are disabled proximity key backlighting of the doorbell button door opener function no relay triggering continuous video transmission In battery mode the door station operates in a power saving mode and wakes up when the doorbell is pressed In this case it takes approx 5 seconds to establish a connection to the main unit We recommend that you run the video door station on a permanent power supply to be able to use the full functionality Connection examples for an electronic door opener door bell Description of the terminal block Description Note O Network connection for video door station 12 24V direct
31. onnect defective devices from the power immediately and contact your specialist dealer If in doubt have a specialist technician carry out assembly installation and connection of the device Improper or unprofessional work on the power supply or domestic installation puts both you and other persons at risk Connect the installations so that the power supply circuit and low voltage circuit always run separately from each other They should not be connected at any point or be able to become connected as a result of a malfunction Avoid the following adverse conditions during operation Moisture or excess humidity Eycasa main unit Extreme heat or cold Direct sunlight Eycasa video door station Dust or flammable gases vapors or solvents Strong vibrations Strong magnetic fields e g next to machines or loudspeakers The camera must not be directed toward the sun as otherwise the sensor may be destroyed Eycasa video door station Unpacking the device Handle the device with extreme care when unpacking it If the original packaging has been damaged inspect the device If the device shows signs of damage return it in the original packaging and inform the delivery service Contents Ts 002010 10 USC sire T 2 Eycasa system COMPONENTS sasori a 7 3 Features and TUMCUIOINS ino er o i eiae o eode ded edo ie got coded oia edu ete eaten 8 4 Device descriIDUOD s sssoiediviesidbotoca teta ein ets niece ec vessel iM E
32. orresponding country flag on the display oO gu cw eo m Press the button twice to return to the live view 28 7 2 Operating the live view Y LI E SS Individual image view 4x view The Eycasa main unit has a touchscreen interface all functions are operated by finger pressure on the appropriate button In the live view the following adjustment options and displays are available Display of the signal strength of the currently selected cameras Note that the signal strength may be displayed only when there is active image content In the 4x view this function is not available Manually select camera 1 to 4 for the individual image view Switches between individual image view and 4x view Button opens the system settings of the Eycasa main unit Operates RELAY 1 on the video door station to open the door Key Establish terminate a voice connection to the video door station Receiver Play a preset lullaby on the Family Care camera for 90 seconds The lullaby is repeated until 90 seconds have passed You can end the lullaby manually by pressing the button Activates monitoring mode on the Family Care camera voice activation is enabled The function remains active until it is manually deactivated again Monitoring mode Information window regarding pending missed event with details on camera name time stamp and event type An event must be acknowledged before other Bu operator inputs on the touchscreen are
33. possible Events are acknowledged by Es o finger pressure on the corresponding message A counter below the event message indicates how many events have occurred since the last acknowledgment 29 Note In the factory setting the Eycasa main unit switches to the screen saver after 2 minutes of inactivity no touchscreen inputs or event messages You can change this in the screen saver menu item 30 T 3 Event list and event behavior Event list In the event list the following control options are available Changes the view to the event list You can browse through the event list in steps of seven using the V3 y buttons The event log includes 500 entries Opens the general filter dialog of the event list After activation of the filter type only events of the selected type are displayed When a camera is selected the event list only shows events of the selected camera The camera filter can be combined with the general event filter Deleting the event log If you press the Delete event log button the entire event log in the Eycasa main unit is deleted and all the associated video recordings are deleted from the SD card Video recording There is a recording of the selected event Tap the event message to play the recording Video recording missing There is a recording of the selected event but it was not found on the SD card the SD card was removed or the recording was manually deleted Doorbell even
34. rocess can take several seconds The setup wizard will signal whether the process is complete or whether it needs to be repeated due to a pairing error Pairing 5of5 Pairing finished The Family Care Camera was successfully paired If the message Family Care camera was successfully assigned appears the assignment process is finished If an error occurs during the process repeat the previous assignment steps You can now proceed with the installation of the unit See section 6 21 5 5 Pairing the Eycasa handset Open the settings in the Eycasa main unit and jump to the Handset menu item 22 05 2014 10 35 05 AM General Handset Pair handset Unpair all handsets Recordings Handset amp e Proximity Key E PM CORN Select Pair handset The main unit will now wait for a handset which is also in pairing mode In your handset select Yes under Settings Pair to start the learning process The learning process takes approx 30 seconds and is acknowledged by a message Pairing If the pairing process fails please ensure that the handset is located in the immediate vicinity of the main unit during the pairing process Step 1 Step 2 Step 3 Step 4 Brightness Do You want to activate Please enable pairing the pairing mode for this mode for your Handset in handset settings page of Eycasa Lock screen Main unit n Yes Remaining time Volume 120 seconds Pairing 22 6 Moun
35. s The local conditions at the installation site may have a negative impact on the range A range of up to 100 m can be achieved if there is line of sight between the receiver and transmitter and a range of up to 30 meters can be achieved indoors this can be less depending on the situation in the building The following environmental conditions compromise both the range and frame rate Mobile communication masts high tension pylons electrical wires ceilings and walls devices with the same or an adjacent wireless frequency Warnings Observe all safety and operating instructions before putting the device into operation for the first time 1 Observe the following information to avoid damage to the power cable and plug Do not modify or manipulate the power cable or plug Do not pull the cable when disconnecting the device from the power always take hold of the plug Ensure that the power cable is positioned as far away as possible from any heating equipment as this could otherwise melt the plastic coating The power supply unit of the outdoor camera must be protected from damp and moisture 2 Follow these instructions Non compliance with these instructions could lead to an electric shock Never open the housing of the outdoor camera or power supply unit Do not insert any metallic or flammable objects into the device Use overvoltage protection to prevent damage caused by overvoltage e g electrical storms 3 Disc
36. se in protected outdoor areas with integrated night vision in close proximity to the camera and control of an electronic door opener e Eycasa outdoor camera with built in night vision in close proximity to the camera e Eycasa Family Care camera with integrated sound detection function VOX for indoors The main unit is the heart of the system Equipped with a 7 touchscreen color display and intuitive user menu Flexible use with wall or table installation The door station provides video images communication and door opening all in one It can be fitted in standard sized intercom systems vertically or horizontally even without power supply IP54 approved for use in protected outdoor areas Wireless connection 24Gnz digital wireless video d e IR wireless outdoor cameras can be integrated for viewing all around the house This installation is particularly useful for areas which are hard to see such as terraces or cellar entrances o Eu a gt 1 9 Ghz DECT audio The white Family Care camera is equipped with infrared night view LEDs to identify persons at close range as well as a noise detection function 4 Device description 4 1 Description of the Eycasa main unit Used for writing short notes on the memo board Dry erase Board marker board marker Intercom for Eycasa video door station and Eycasa FamilyCare camera Increases the volume during voice commu
37. sion Eycasa 1 5 or higher You can download the software free of charge from the following website http www abus com ger Sicherheit Zuhause Tuersicherheit Tuersprechsysteme Eycasa Eycasa Tuer Haus Funk Videosystem Electronic Electromechanical door bell door bell T 12V 24V RELAY RELAY 12V 24V RELAY RELAY AC DC 2 e ACIDC l 2 230V Qo Q 4 3 Description of the Eycasa outdoor camera Q Cil 1 D Aema 000000 Screw on antenna for 2 4 GHz digital wireless Sensor for Unser between day and night mode red Permanently lit Power supply connected e Power LED y ai LED rm NO power supply connected signal to the main unit S Pairing mode active Camera not paired or not LED off Permanent accessible through the main unit IR LEDs Builtin IR LEDs Activated in night mode in IR LEDs Activated in Builtin IR LEDs Activated in night mode mode The PIR sensor reports motion detection to the Eycasa main PIR sensor PIE Mine Wall mount for camera mounting Pairing button for programming the wireless camera in the Power supply Connection for 5 V DC 1 A power supply 4 4 Description of the Eycasa Family Care camera OOOOOOO O CO000000 Camera module with fixed lens and IR LEDs including photo Camera sensor IR LEDs Built in IR LEDs Activated in night mode Light sensor sensor for switching between day and night mode Indicates the stat
38. t Shows the time of the doorbell ringing of an Eycasa video door station Proximity key Shows the time the door was opened by a wireless proximity key on the video door station Doorbell rings missed Shows the time of a missed doorbell ring This event is always displayed when the previous doorbell ring was not acknowledged within 30 seconds Motion Shows the time of motion detection by the PIR sensor of an Eycasa outdoor camera Family Care Shows the time of a VOX alarm on the Family Care camera Family Care missed Shows the time of a missed VOX alarm This event is always displayed when the previous VOX alarm was not acknowledged within 30 seconds Video signal failure Shows the time of a failed signal connection between the main unit and camera This message appears when the wireless signal fails for longer than 1 minute 31 Battery strength Shows the time of weak battery strength on an Eycasa video door station and Family Care camera When the battery is low the video door station automatically switches off video transmission Change the batteries promptly if this message appears 7 3 1 Playback of event recordings Event list Possible user actions Select an entry with the video symbol The view automatically switches to playback and the video is from the event list played The control buttons are automatically hidden after a short while Touch the monitor once to see the control buttons again The vie
39. thin the Eycasa software the key must be held up to the video door station 11 07 2013 2 47 43 PM Proximity Key No Name O 1 key De General Gy Cameras O 2 key2 Proximity Key P Reset D Pair a new key with the video door station Scroll list upwards for more than 5 chip keys Scroll list downwards for more than 5 chip keys Reload the chip key list on the video door station Chip key status display X chip key inactive v chip key active Pairing the proximity key Press the Pair proximity key button to pair new chip keys on your video door stations After the Pair proximity key button is pressed pairing mode is activated on all connected video door stations for 120 seconds Put your chip key into the detection range marked in red of the video door station Note Pairing mode is automatically ended on all video door stations if no chip key is paired during pairing mode 45 Pairing proximity key _ Pairing proximity key Hold the proximity key above the sensor of the chip reader at your video door station The pairing of your proximity key at video door station Door succeeded Remaining time 111 seconds Name ey 0 where you want to pair the key Do you want to pair more keys Cancel After successful pairing you can specify a name for the chip key and then pair further keys If you answer the question with No pairing mode is terminated on all video door statio
40. ting the system components 6 1 Mounting the Eycasa main unit The Eycasa main unit can be installed either on a table or wall When delivered the table mount is already attached allowing you to place the device wherever you would like indoors Alternatively the back cover of the main unit can be replaced with the included wall mount The following steps describe how to install the wall mount Important Choose the installation location of the main unit so that optimal range of all Eycasa components is possible Make sure that a distance of no more than 30 m depending on the building characteristics this can be less from the main unit is not exceeded Additional walls can reduce the wireless range Test the range before installation 1 Remove the table mount on the rear of the device by pushing the back cover downwards and off Be sure not to touch or damage electronic components while the main unit is open 2 Put the wall mount into the desired position on the wall and mark the drill holes The distance between the two holes is 102 mm 3 Attach the screws using wall plugs and put on the wall mount The wall mount should be completely screwed together only after placement onto the screw heads 23 4 Now place the main unit on the wall mount and connect the included power supply unit 6 2 Mounting the Eycasa video door station The Eycasa video door station can be mounted either horizontally or vertically The vide
41. us of Family Care camera progress LED green pe to main unit Status LED LED acer Flashin Audio connection to main 9 9 unit established LED red Flashing slowly 2 Deedon main Unit interrupted Flashing LED red quickly Battery critically low Mikrofone Built in microphone for two way communication with Eycasa main unit and voice detection using VOX function o pme Antenna for 2 4 GHz digital wireless Switch on Family Care camera press for 3 seconds Switch off Family Care camera press for 3 seconds mee ERE OEP Fe See nine ycasa main unit Loudspeaker Integrtedloudspeake loudspeaker ri Thread for bracket Camera mount for versatile attachment 4 5 Description of the Eycasa handset Speaking button Microphone Loudspeaker Clip Door opening button Power on off back Disconnection button Charging pins Ml Removable foot A ii 5 V power supply lt i I 87 USB interface for updates Charging pins The handset is equipped with a touch sensitive display For the settings please jump to menu item 7 8 To switch the handset on or off please press and hold the red button for at least 5 seconds When the handset battery is discharged a signal tone will be emitted in regular intervals Please place the handset in the charging cradle The handset will be fully charged after approx 5 6 hours 5
42. use any chemical cleaning products as they could damage the surface of the housing discoloration 9 Disposal Devices displaying this symbol may not be disposed of with domestic waste At the end of its service life dispose of the product according to the applicable legal requirements Please contact your dealer or dispose of the products at the local collection point for electronic waste 50 10 Technical data Model number CASA30100 Eycasa video door station Eycasa main unit 1 4 CMOS Horizontal angle of view Installation Surface mounting IP degree of protection IP54 10 C 50 C 600g Net weight 600 g Model number CASA30200 Eycasa main unit Max 1 x Eycasa video door station max 3 x Eycasa outdoor Connectible devices PORSCHE Audio modulation 51 o OO o 670g 00 0 Net weight 670g Model number CASA30300 Eycasa handset Table mount wall mount Event log 500 power 30 m depending on site conditions 8 Ohm 1W 8 Ohm IW Integrated Power supply 5VDC 1A Degree of protection IP30 Max 600 mA Operating temperature 10 C 50 C Dimensions W x H x D 74x127x19 Net weight 230g 52 Model number CASA30400 Eycasa Family Care camera Permanent power supply or battery powered 1 4 CMOS 3 27 mm Range of night vision function IRange A4 90 VOX sensitivity 5 levels Rechargeable battery running time 3 hours of continuous oper
43. w automatically switches back to the event list once the video has been completely played back 44 gt gt Fast forward rewind playback Press the buttons nbn RN Pause replay Press the button Drag the time line Position the playback button horizontally by dragging and dropping it anywhere on the time line to skip to a particular point during playback Note Alternatively you can press the Back and Event list buttons on the main unit below the screen to end playback of a video file 32 7 3 1 Doorbell event Sequence of doorbell ringing 1 puo Iw UM Doorbell is pressed on the video door station The screen on the Eycasa main unit is activated RELAY2 on the door station is switched for 2 seconds to activate the door bell The live image of the video door station is displayed Video recording is started on the video door station and continues for up to 30 seconds if the Activate video recording option was selected in the settings The doorbell tone plays The event message is displayed on the screen At the same time the video image and a doorbell signal are sent to the CASA30300 handset optional Possible user actions on the handset Acknowledge the event message The doorbell ringing is interrupted Press the button After the event message is acknowledged the and P buttons can be pressed The event message is acknowledged and the doorbell ringing ends An
44. y Key Volume touch click Reset 39 Here you set the current time date and time zone These settings are important for proper recording of the messages in the event log of the main unit 7 4 6 Time and date settings 2671172013 8 03 00 AM General Clock Setting date and time esta Automatic use network provided values Time Date Gy Cameras e Recordings Proximity Key T T T On PM 7 Time zone P Reset Europe Amsterdam GM1T 01 00 WF Activate the Automatic setting if your Eycasa main unit is connected to your home network which provides access to the internet The current time is identified automatically via NTP Network Time Protocol any regularly synchronised Synchronisation takes place once a day or when the Eycasa main unit is restarted Set the time zone regardless of whether manual or automatic setting is selected Important Settings for the date and time must be made during initial start up If the main unit loses power the time settings are buffered in the device for about 15 minutes If your main unit is separated from the line voltage for a long period of time the settings must be made again 7 4 7 Network settings Activate the network port of your Eycasa main unit here This option is deactivated on delivery 2871172013 8 14 129 AM w Activate network General Dhcp nd Gy Cameras Static IP address IP address 192 168 106 137 Del Recordings Su
Download Pdf Manuals
Related Search