Plantronics CS510-XD
Contents
1. Daily Use plantronics Place an Outgoing Call 1 Wearing your headset press the headset call control button 2 Remove the handset from the cradle You will hear a dial tone NOTE This step will be automatic if you install a lifter or EHS cable accessory For a complete list of accessories visit plantronics com accessories 3 Dial the number using your desk phone 4 To end the call press the headset call control button and hang up the handset Answer an Incoming Call 1 Wearing your headset press the headset call control button 2 Remove the handset from the cradle and speak to your caller NOTE This step will be automatic if you install a lifter or EHS cable accessory For a complete list of accessories visit plantronics com accessories 3 To end the call press the headset call control button and hang up the handset Conference Up to Three Additional Headsets You can conference up to three additional headsets to a call in progress NOTE Only XD headsets will work with XD bases Join a Conference Call While in an active link between the primary headset and the base on a call place the guest headset into the primary user s charge cradle this connects the headset to the base The base subscription LED will begin flashing After a few moments the primary user will hear a triple tone in their headset indicating the guest headset wishes to join the call Within ten seconds of hearing the triple tone press the primary2. HL10 lifter continue below If you will be using the desk phone with an EHS cable refer to Desk phone plus EHS cable section in this guide For further installation information refer to the EHS Getting Started guide that came with your EHS cable or at plantronics com accessories Desk Phone standard Connect one end of the telephone interface cable to the back of the base Disconnect the handset coil cord from the desk phone and re connect it to the telephone interface cable junction box Connect the remaining end of the telephone interface cable into the open handset port on the desk phone NOTE Your desk phone handset will continue to work it s just hooked up differently NOTE f your phone has a built in headset port you should only use the headset port if you will not be using the HL10 lifter In this configuration you must press both the headset button on your phone and the call control button on the headset to answer or end calls plantronics Check Configuration and Make a Test Call 1 If your desk phone has a volume control set it to mid range 2 Look at the bottom panel of your base and make sure the default settings are correct Listening volume dial 4 2 and Speaking volume dial 2 Configuration switch A Desk phone volume mid range plantronics Ca pre rete 3 Remove the handset from desk phone cradle 4 While wearing your headset press the
3. call control button on the headset 5 If you do not hear a dial tone adjust the configuration switch A G until you do NOTE For most phones the factory default settings will sound the best 6 Dial a test call from the desk phone If needed fine tune the volume with the headset volume controls You can also adjust the desk phone speaking and listening volumes on the bottom of the base Desk Phone plus HL10 Lifter sold separately NOTE First follow the steps above for Desk Phone Standard 1 Firmly press the handset lifter power cord into the handset lifter jack 2 While wearing your headset slide the handset lifter arm under the handset until the lifter base touches the side of the phone 3 Slide the lifter up to where it nearly touches the handset earpiece 4 Press the call control button on your headset to activate the lifter 5 If you hear a dial tone the lifter is set correctly and needs no adjustment 6 Remove the protective strips from the 3 mounting tapes on the underside of the lifter 7 Gently place the lifter on the desk phone in the pre determined position 8 Press firmly to adhere plantronics If You Do Not Hear a Dial Tone 1 If you do not hear a dial tone raise the lifter height switch to the next highest position 2 Repeat steps 2 through 5 above as necessary until you hear a dial tone 3 When you hear a dial tone secure the lifter as described in steps 6 through 8 Additional Parts if re
4. 350 XD EHS and HL10 are trademarks or registered trademarks of Plantronics Inc All other trademarks are the property of their respective owners Patents US D535 285 D538 785 BR DI71026967 CN ZL200630123314 7 ZL200630123313 2 201130145424 4 EM 000543798 0004 000543798 0005 001 865510 0001 IN 236857 TW D117515 D117333 Patents Pending 88949 06 02 13 plantronics
5. CS510 XD CS520 XD Wireless Headset System User Guide plantronics S p Contents plantronics Welcome 3 What s in the Box 4 Base and Headset Basics 5 Accessories 6 Headset Set Up 7 Connect Your Desk Phone 8 Connect the Power 8 Charge the Headset 8 Connect and Configure Your Desk Phone 9 Desk Phone standard 9 Check Configuration and Make a Test Call 10 Desk Phone plus HL10 Lifter sold separately 11 Desk Phone plus EHS Cable 13 Position Your Base 14 Your Headset 15 Headset Controls 15 Talk Time 15 Battery 16 Muting Your Headset During a Call 16 Adjusting Your Headset Volume 16 Out of Range Warning Tones 16 Your Base 17 Base Phone Button and Switches 17 Subscription Button 17 Wideband Narrowband Audio Switch 18 Auto Answer Switch 19 Daily Use 20 Place an Outgoing Call 20 Answer an Incoming Call 20 Conference Up to Three Additional Headsets 20 Troubleshooting 21 Headset 21 Desk Phone 21 Welcome Congratulations on purchasing your new Plantronics product This guide contains instructions for setting up and using your CS510 XD CS520 XD Wireless Headset System Please refer to the separate safety instructions for important product safety information prior to installation or use of the product plantronics 3 What s in the Box Headset Model WH350 XD binaural shown Model WH300 XD monaural available Telephone interface cable Power supply pl
6. antronics Base and Headset Basics Base overview FRONT BACK 1Call mute LED 2 Power on subscription LED BOTTOM 3 Charging LED 4 Subscription button 5 Narrowband wideband audio switch 6 Power jack 7 Handset lifter EHS cable jack 8 Telephone interface cable jack 9 Auto answer switch 10 Listening volume dial 11 Speaking volume dial 12 Configuration switch For installation set up Headset overview 1 Headband 2 Volume down button 3 Headset LED 4 Volume up button 5 Call control button 6 Mute button 7 Microphone plantronics Accessories 1 Electronic hookswitch cable EHS Electronically takes your desk phone handset off hook Enables remote call answer end with your headset 2 HL10 lifter Automatically lifts handset and returns it to the cradle Enables remote call answer end with your headset 3 Online indicator OLI A light that flashes once a call is activated It allows others to know when you are on a call plantronics Headset Set Up Your headset comes fully assembled You can adjust the headband for a better fit and the mouthpiece for optimal performance Adjust the Headband 1 To adjust the headband lengthen or shorten the band until it fits comfortably The clickstop feature keeps the headband securely adjusted 2 Position the headset so that the leather ear cushion s sit comfortably over the center of your ear s For the WH300 XD headset
7. e distortion is still present adjust the headset volume control to lower the headset speaker volume If the distortion persists lower the Listening volume dial on the base Make sure there is at least 12 inches between your base and your computer and at least 6 inches between your base and your telephone hear echo in the headset People talk to can hear a buzz in the background Lower the Listening volume dial and Speaking volume dial on the base For most telephones the correct setting is position 2 If the audio level is too low in this position adjust the headset volume control to increase the headset speaker volume If your speaking volume is too low for your listener in this position adjust the position of the headset to make sure the microphone is a finger s width from the corner of your mouth Adjust the Configuration switch The most commonly used position is A Move the base further away from your phone If the base power supply is plugged into a power strip plug it into the wall directly The handset lifter is installed but does not lift the handset Be sure the handset lifter power cord is firmly pushed into the handset lifter jack on the base 21 NEED MORE HELP plantronics com support Plantronics Inc 345 Encinal Street Santa Cruz CA 95060 United States 2013 Plantronics Inc All rights reserved Plantronics the logo design CS510 XD CS520 XD CO52 XD WH300 XD WH
8. headset s call button to accept the guest headset If the process fails or times out because the button was not pressed within ten seconds the guest subscription is terminated and the guest will hear an error tone in their headset To connect a guest headset that is of different variety than the primary headset press the base subscription button while the base has an active link Next press the guest headset volume up button until the indicator light turns on The base subscription LED will begin flashing and the primary user will hear a triple tone in their headset indicating the guest headset wishes to join the call Within ten seconds of hearing the triple tone press the primary headset s call button to accept the guest headset If the process fails or times out because the button was not pressed within ten seconds the guest subscription is terminated and the guest will hear an error tone in their headset NOTE Headsets in a conference maintain independent mute controls The base only indicates the primary user s mute state Exit a Conference Call Guests headsets can remain as guests through multiple calls To remove a guest headset press the guest headset s call button or dock the primary user s headset in the charge cradle A single tone in the master headset will be heard as each guest leaves the call 20 Troubleshooting plantronics Headset Headset has to be charged too often Talk time is not as long as stated Swi
9. lume button Press to lower volume 2 Headset LED Flashes green when in use 3 Call control button Place answer end a call Briefly press the call control button 4 Mute button Press to mute unmute 5 Volume button Press to increase volume IMPORTANT For your safety do not use headset at high volumes for extended periods of time Doing so can cause hearing loss Always listen at moderate levels For more information on headsets and hearing visit plantronics com healthandsafety Talk Time With a single full charge the CS510 XD CS520 XD will provide up to eight hours of talk time in narrowband mode and five hours in wideband mode Talk time will be reduced when headset is used consistently at a long distance from the base plantronics 15 plantronics Battery This product has a replaceable battery To ensure replacement batteries meet Plantronics high quality standards and for optimal performance only use replacement batteries provided by Plantronics Low Battery Warning If you are on a call and the headset battery is critically low you will hear a repeated single low tone every 15 seconds indicating that the battery is low You should recharge the headset immediately If you are not on a call and press the call control button you will hear three low tones if the battery is critically low You should recharge the headset immediately Muting Your Headset During a Call To mute unmute the call pre
10. position the stabilizer T bar above your ear 3 Fora tighter fit gently pull the opposite end of the headset inward as shown Adjust the Mouthpiece 1 Carefully bend and shape the boom with both hands as shown Avoid bending or twisting the boom near the microphone or earpiece 2 Position the click stop turret and boom so that the microphone is two finger widths from the corner of your mouth front back plantronics Connect Your Desk Phone This section describes how to connect the base to your desk phone Connect the Power Plug one end of the power supply into the power jack on the back of the base and the other end into a working power outlet The Power On LED will be solid white Charge the Headset Place the headset in the charge cradle The charging LED on the base will flash green when charging and turn solid green when the headset is fully charged Charge for at least 20 minutes prior to the first use A full charge takes 3 hours NOTE The product has a replaceable battery Contact Plantronics for replacement information plantronics plantronics Connect and Configure Your Desk Phone There are three setup options for connecting the CS510 XD CS520 XD to your desk phone Select one of the following and continue Desk phone standard Desk phone HL10 lifter sold separately Desk phone EHS cable sold separately NOTE f you will be using a standard desk phone set up or a desk phone with an
11. quired Use extender arm when the handset lifter needs additional stability lifting and returning handset to cradle Extender Arm 1 Slide extender arm onto lifter 2 Stabilizers can be shifted left and right Position stabilizers on outsides of handset to gently grip the handset Ringer Microphone Use ringer microphone only when the telephone speaker is not located directly under the handset 1 Remove cover from ringer microphone jack on back of lifter 2 Connect ringer microphone plug 3 Place ringer microphone over phone speaker Remove adhesive tape and attach plantronics 12 For Nortel Phones Only Desk Phone plus EHS Cable Connect the end of the EHS cable to the base and the other end to the desk phone as described in the EHS Adapter Getting Started guide y NOTE For further installation information refer to the EHS Getting Started guide that came with your EHS cable or at plantronics com accessories plantronics 13 plantronics Position Your Base The minimum recommended separation between your desk phone and the base is 6 inches The minimum recommended separation between the base and computer is 12 inches Incorrect position can cause noise and interference problems 14 Your Headset Now that you ve adjusted your headset and connected your desk phone read this section to learn about the headset features how to use the controls and more Headset Controls 1 Vo
12. ribed to XD bases If you try to subscribe a non XD headset to an XD base the power LED on the base will turn off and will remain off until the non XD headset is removed from the base Automatic Secure Subscription With your system idle docking a headset will automatically subscribe it to the base making it the primary headset The Power On Subscription LED will flash white during subscription process and become solid white when the new subscription is established Manual Over the Air Subscription 1 With your system idle and your headset undocked press and hold the subscription button on the base for three seconds The Power on subscription light will flash white 2 Press and hold the volume up button on the headset for three seconds until the headset LED turns solid green When the Power on subscription LED on the base becomes solid white the headset and base are subscribed to one another NOTE f the subscription process times out after two minutes or if the subscription process fails the subscription LED on the base will go dark for three seconds and then re illuminate steadily to indicate power is applied to the base If this occurs try to re subscribe the headset again Ending Subscription If the base is in subscription mode and you want to stop the base from searching for a headset press the subscription button again The subscription LED on the base will go dark for three seconds and then re illuminate steadily to indicate power i
13. s applied to the base plantronics 7 plantronics Power On Subscription LED Base Status Power On Subscription LED Primary headset subscription Flashes white Primary headset subscribed to base Solid white Conference call headset subscription Flashes white Active conference call with guest headsets Flashes white rapidly Incompatible headset and base Off 2 Wideband Narrowband Audio Switch The CS510 XD CS520 XD has wideband audio which allows speech to sound clearer and more natural If your desk phone is capable of wideband audio set the Wideband Narrowband audio switch to yellow for wideband NOTE Talk time will be reduced when operating in wideband mode SB Moo H g H Set the switch to black narrowband for longer headset battery life or to increase the number of systems that can work in a small area MAY Auso y 18 3 Auto Answer Switch Auto answer saves a button press to establish the radio link between headset and base When auto answer is set to black you must press the headset call control button to answer an incoming call aia TOSI amp H When Auto Answer is set to gray you can answer a call just by lifting headset from the base 0 UXO Ausan ay NOTE Auto answer end capability requires the use of an EHS cable or HL10 lifter Visit plantronics com accessories for more information plantronics 19
14. ss the mute button When mute is activated on the primary headset the Call mute LED on the base will be solid red and you will hear three high tones you will still be able to hear the caller Adjusting Your Headset Volume Fine tune your headset volume by pressing the volume button to increase or the volume button to decrease Make set up volume adjustments for the desk phone with the volume dials on the base Out of Range Warning Tones If you are on a call and go out of the operating range you will hear three low tones You will hear a single mid tone when you are back in range If you stay out of range an active call will be suspended The call will be re established when you walk back into range If you remain out of range for more than 5 minutes the system will drop the call If you are not on a call and go out of the operating range and then press the call control button you will hear a single tone for the button press and three low tones for the failure to make a link 16 Your Base Base Phone Button and Switches 1 Subscription Button The headset and base that came in the box are subscribed connected to each other However if you wish to use a new headset or need to restore subscription to your current headset the units can be subscribed to each other by the following two methods NOTE The red CSSOOXD markings on the base and headset indicate an XD headset system and only XD headsets can be subsc
15. tch the Wideband Narrowband audio switch to narrowband black Talk time performance is significantly degraded even after a full recharge Battery is wearing out Call Plantronics at 800 544 4660 for factory replacement information or contact us at plantronics com support can t subscribe a headset to the base Make sure both the headset and base have the red XD markings See Subscription button in this user guide Desk Phone can t hear a dial tone in the headset Make sure your headset is charged Make sure your headset is subscribed to base See Subscription button Press the call control button on your headset If using a lifter make sure the lifter is lifting the handset high enough to operate the hookswitch set to a higher setting if necessary Adjust the configuration switch on the base until a dial tone is heard Fine tune the listening volume on the headset If the volume is still too low adjust the Listening volume dial on the base hear static Make sure there is at least 12 inches between your base and your computer and 6 inches between your base and your telephone You may hear static as your headset is going out of range move closer to the base The sound is distorted Lower the Speaking volume dial or Listening volume dial on the base For most telephones the correct setting is position 2 If your desk phone has a volume control lower until the distortion disappears If th
Download Pdf Manuals
Related Search