Home

Samsung S22A650S

Contents

1. Do not install the product on an unstable or vibrating surface insecure shelf sloped surface etc e The product may fall and break or cause a personal injury e Using the product in an area with excess vibration may damage the product or cause a fire Do not install the product in a vehicle or a place exposed to dust moisture water drips etc oil or smoke e An electric shock or fire may result Do not expose the product to direct sunlight heat or a hot object such as a stove e Otherwise the product lifespan may be reduced or a fire may result Do not install the product within the reach of young children e The product may fall and injure children Take care not to drop the product when moving it e Otherwise product failure or personal injury may result Do not set down the product on its front e _ The screen may become damaged When installing the product on a cabinet or shelf make sure that the bottom edge of the front of the product is not protruding e The product may fall and break or cause a personal injury e Install the product only on cabinets or shelves of the right size Operation A Warning Before Using the Product Put down the product carefully e The product may fall and break or cause a
2. Tightly fasten the screw to the After installing the stand place You can remove the fixing pin bottom of the base the product upright and adjust the stand now Caution Do not hold the product upside down only by the stand NG The color and shape of parts may differ from what is shown Specifications are subject to change without notice to improve quality Preparations 1 3 2 Adjusting the Product Tilt and Height NG The color and shape of parts may differ from what is shown Specifications are subject to change without notice to improve quality Sada e To adjust the height remove the fixing pin e The monitor tilt and height can be adjusted e Hold the top center of the product and adjust the height carefully 1 3 3 Rotating the Monitor You can rotate your monitor as shown below i I gt Be sure to fully extend the stand before rotating the monitor e If you rotate the monitor without fully extending the stand the corner of the monitor may hit the floor and get damaged e Do not rotate the monitor counterclockwise The monitor may get damaged Preparations 1 3 4 Installing a Wall mount Kit or Desktop Stand Before Installation A Power the product off and remove the power cable from the power socket
3. Place a protective cloth or Unfasten the screw from the Lift and detach the stand cushion on a flat surface Next back of the product place the product with the face down on top of the cloth or cushion Installing a Wall mount Kit or Desktop Stand Q Attach the wall mount kit or desktop stand here O Bracket sold separately Align the grooves and tightly fasten the screws on the bracket on the product with the corresponding parts on the wall mount kit or desktop stand you want to attach Preparations Notes R Using a screw longer than the standard length can damage the internal components of the product e The length of screws required for a wall mount that does not comply with the VESA standards may vary depending on the specifications e Do not use screws that do not comply with the VESA standards Do not attach the wall mount kit or desktop stand using excessive force The product may get damaged or fall and cause personal injury Samsung shall not be held liable for any damage or injury caused by using improper screws or attaching the wall mount kit or desktop stand using excessive force e _ Samsung shall not be held liable for any product damage or personal injury caused by using a wall mount kit other than the one specified or from an attempt to install the wall mount kit on your own e _ To mount the product on a wall en
4. 3 7 Screen Setup Response Time Accelerate the panel response rate to make video appear more vivid and natural Wg gt Itisbestto set Response Time to Normal or Faster when you are not viewing a movie e The functions available on the monitor may vary depending on the model Refer to the actual product 3 7 1 Configuring Response Time 7 Press MENU on the product 2 Press a v to move to PICTURE and press 53 on the product 3 Press a v to move to Response Time and press 3 on the product The following screen will appear PICTURE Normal Faster Fastest AUTO 0 4 Press a v to move to the option you want and press the 0 0 5 The selected option will be applied 3 Screen Setup 4 1 Configuring Tint Adjust the tint of the screen This menu is not available when jX jcBright is set to Cinema or Dynamic Contrast mode Red Adjust the value of the color red in the picture Range 0 100 A higher value will increase the intensity of the color WZ This menu is not available when fen GicColor is in Full or Intelligent mode 4 1 1 Configuring Red Press MENU on the product 2 Press a v to move to COLOR and press 3 on the product 3 Press a v to move to Red and press 3 on the product The following screen will appear 4 Adjust the Red using the a v button 4 Configuring Tint 48 4 2 Configuring Tint Green Adjust the value of the col
5. 5 The selected option will be applied 6 Setup and Reset 66 6 5 Setup and Reset Auto Source Activate Auto Source 6 5 1 Configuring Auto Source 1 2 Press MENU on the product Press a v to move to SETUP amp RESET and press on the product Press a v to move to Auto Source and press on the product The following screen will appear SETUP amp RESET Auto EISEN e Auto The input source is automatically recognized e Manual Manually select an input source Press a v to move to the option you want and press the 5 6 The selected option will be applied 6 Setup and Reset 6 6 Setup and Reset Display Time Set the on screen display OSD menu to automatically disappear ifthe menu is not used for a specified period of time Display Time can be used to specify the time after which you want the OSD menu to disappear 6 6 1 Configuring Display Time Press MENU on the product 2 Press a v to move to SETUP amp RESET and press 3 on the product 3 Press afv to move to Display Time and press 3 on the product The following screen will appear SETUP amp RESET MG 10 sec 20 sec 200 sec AUTO 4 Press a v to move to the option you want and press the 0 0 5 The selected option will be applied 6 Setup and Reset 68 Setup and Reset 6 7 Key Repeat Time Control the response rate of a button when the button is pressed 6 7 1
6. A serious or fatal injury may result if instructions are not followed A Caution Personal injury or damage to properties may result if instructions are not followed O Activities marked by this symbol are prohibited Instructions marked by this symbol must be followed Before Using the Product Cleaning Cleaning Exercise care when cleaning as the panel and exterior of advanced LCDs are easily scratched Take the following steps when cleaning 1 Power off the monitor and computer 2 Disconnect the power cord from the monitor 14 Hold the power cable by the plug and do not touch the cable with wet hands Otherwise an electric shock may result 3 Wipe the monitor with a clean soft and dry cloth e Donot apply a cleaning agent that contains alcohol solvent or surfactant to the monitor e Donot spray water or detergent directly on the product 4 Wet a soft and dry cloth in water and wring thoroughly to clean the exterior of the monitor 5 Connect the power cord to the product after cleaning the product 6 Power on the monitor and computer Before Using the Product Securing the Installation Space e Ensure some space around the product for ventilation An internal temperature rise may cause fire and damage the product Be sure to allow the amount of space as shown below or greater when installing the product A The e
7. The color and the appearance may differ depending on the product and the specifications are subject to change without prior notice to improve the performance BN46 00081D 03 Before Using the Product Copyright The contents of this manual are subject to change without notice to improve quality 2011 Samsung Electronics Samsung Electronics owns the copyright for this manual Use or reproduction of this manual in parts or entirety without the authorization of Samsung Electronics is prohibited The SAMSUNG and SyncMaster logos are registered trademarks of Samsung Electronics Microsoft Windows and Windows NT are registered trademarks of Microsoft Corporation VESA DPM and DDC are registered trademarks of the Video Electronics Standards Association e An administration fee may be charged if either o a an engineer is called out at your request and there is no defect in the product i e where you have failed to read this user manual o b you bring the unit to a repair centre and there is no defect in the product i e where you have failed to read this user manual e The amount of such administration charge will be advised to you before any work or home visit is carried out Before Using the Product Icons used in this manual The following images are for reference only Real life situations may differ from what is shown in the images Symbols for safety precautions A Warning
8. www samsung com PUERTO RICO 1 800 682 3180 http www samsung com TRINIDAD amp TOBAGO 1 800 SAMSUNG 726 7864 http www samsung com VENEZUELA 0 800 100 5303 http www samsung com EUROPE AUSTRIA 0810 SAMSUNG http www samsung com 7267864 0 07 min BELGIUM 02 201 24 18 http www samsung com be Dutch http www samsung com be fr French BOSNIA 05 133 1999 http www samsung com BULGARIA 07001 33 11 normal tariff http www samsung com CROATIA 062 SAMSUNG 062 726 7864 http www samsung com CYPRUS 8009 4000 only from landline http www samsung com 30 210 6897691 from mobile and land line Appendix 85 Appendix EUROPE CZECH 800 SAMSUNG 800 726786 http www samsung com Samsung Electronics Czech and Slovak s r o Oasis Florenc Sokolovska 394 17 180 00 Praha 8 DENMARK 70 7019 70 http www samsung com EIRE 0818 717100 http www samsung com ESTONIA 800 7267 http www samsung com FINLAND 09 85635050 http www samsung com FRANCE 01 48 63 00 00 http www samsung com GERMANY 0180 5 SAMSUNG bzw http www samsung com 0180 5 7267864 0 14 Min aus dem dt Festnetz aus dem Mobilfunk max 0 42 Min GREECE 80111 SAMSUNG 80111 726 http www samsung com 7864 only from land line 30 210 6897691 from mobile and land line HUNGARY 06 80 SAMSUNG 726 7864 http www samsung com ITALIA 800 SA
9. r f Search Contor Pant 2 o Control Panel Home Change the appearance of your displays Make it easier to read what s on your screen RA fashion You can change the size of text and other items on your screen by choosing one of these options To temporarily enlarge just part of the screen use the Magnifier 9 calibrate color tool Change display settings Connect to a projector Sater 200 deln Preview Adjust ClearType text Set custom text size DPD Medium 125 nayang dem __ anton pews cose Cremation nmcape o See also Mapa us soado any On gt Personalization dk Some items may not fit on your screen if you choose this ne setting while your display is set to this resolution asoan poaa Camac ss a punyecner igr press tre AP ay ang tap P Vine tert od ote en yo eee We Orig warn Oued cone Connecting and Using a Source Device 2 3 Connecting Headphones AUDIO IN 7 Connect the stereo cable to the AUDIO IN port on the back of the product and the AUDIO OUT port on the PC WZ Ifthe stereo cable is connected the Volume VOL can be adjusted using the a v buttons on the front of the product 2 Connect an audio output device such as headphones or speakers to KN on the product 2 4 Connecting and Using a Source Device Connecting the Product to aPC as a USB HUB 2 4 1 Connecting a PC to the Product NG The product can function as a HUB by connecting to a PC via a USB cable You can
10. still turned on Press a v to move to the option you want and press the 5 6 The selected option will be applied e _ The performance of Eco Motion Sensor is maximized to a specific user distance 1m and angle 40 degrees e The sensor may not detect you if you are motionless e If you think that the mode entry message appears too frequently increase the time setting of the Eco Motion Sensor or turn the Eco Icon Display Off e Avoid using radio equipment such as a walkie talkie near the product as this may cause a product malfuction 6 Setup and Reset Setup and Reset 6 1 2 Eco Light Sensor The Eco Light Sensor feature optimizes the view condition and contributes to power saving by adjusting the screen brightness depending on the ambient light intensity IZ gt This menu is not available when Eco Saving is set e This menu is not available when Ma GicBright is in Dynamic Contrast mode Configuring Eco Light Sensor Press MENU on the product Press a v to move to SETUP amp RESET and press 03 on the product Press a v to move to ECO and press on the product A N ra Press a v to move to Eco Light Sensor and press 9 6 The following screen will appear e Off Deactivate the Eco Light Sensor function e On Automatically adjust the brightness according to the ambient light intensity 5 Press a v to move to the option you want and press the D 6 The selected option will be appli
11. 2 INFORMATION Menu and Others INFORMATION View the current input source frequency and resolution 7 1 1 Displaying INFORMATION Press MENU on the product 2 Press a v to move to INFORMATION The current input source frequency and resolution will appear NG A 00 Ko SIZE amp POSITION Analog 67 6kHz 60Hz PP SETUP amp RESET 1920 x 1080 INFORMATION EXIT Lv 4 AUTO 0 v v v KA v Configuring Brightness in the Startup Screen Adjust Brightness using the button in the startup screen where there is no on screen display menu available 7 Press in the startup screen The following screen will appear Brightness 2 Adjust the Brightness using the a v button K Volume VOL can be adjusted if a cable is connected to the DP IN or AUDIO IN port A 7 INFORMATION Menu and Others 8 1 Troubleshooting Guide Requirements Before Contacting Samsung Customer Service Center 8 1 1 Testing the Product W4 Before calling Samsung Customer Service Center test your product as follows If the problem persists contact Samsung Customer Service Center Check if your product is operating normally by using the product test function If the screen is turned off and the power indicator blinks even though the product is properly connected to a PC perform a self diagnosis test Power off both the PC and product Disconnect the cable from the product Power on th
12. A e This menu is not available when MaGic Bright is set to Dynamic Contrast mode e This menu is not available when Eco Light Sensor or Eco Saving is set to On 3 2 1 Configuring Brightness 7 Press MENU on the product 2 Press a v to move to PICTURE and press 3 on the product 3 Press a v to move to Brightness and press on the product The following screen will appear PICTURE v v 4 Adjust the Brightness using the a v button 3 3 Screen Setup Contrast Adjust the contrast between the objects and background Range 0 100 A higher value will increase the contrast to make the object appear clearer Z gt This menu is not available when ac cBright is in Cinema or Dynamic Contrast mode a e This menu is not available when acc Color is in Full or Intelligent mode 3 3 1 Configuring Contrast 7 Press MENU on the product 2 Press a v to move to PICTURE and press 3 on the product 3 Press a v to move to Contrast and press 3 on the product The following screen will appear PICTURE 4 Adjust the Contrast using the afv button 3 4 Screen Setup Sharpness Make the outline of objects more clear or blurry Range 0 100 A higher value will make the outline of objects clearer We gt This menu is not available when Ma GicBright is in Cinema or Dynamic Contrast mode a e This menu is not available when MAGieColor is in Full or Intelligent
13. This image is for reference only 4 Store the box in a dry area so that it can be used when moving the product in the future Preparations 1 1 2 Checking the Components K e Contact the dealer from whom you purchased the product if any item is missing e The appearance of the components and items sold separately may differ from the image shown Components lt Kr Quick setup guide Warranty card User manual Power cable DC power adapter Stand base D SUB cable USB cable Stereo cable x DP cable A e Components may differ in different locations e The DP cable is supplied as a component only when the eleventh separator of the model code indicated on the label on the back of the monitor is K ex LS24A650SSK Items sold separately WZ The following items can be purchased at your nearest retailer a HDMI DVI cable DVI cable 1 Preparations FIT Preparations 1 2 Parts 1 2 1 Frontal Buttons WZ The color and shape of parts may differ from what is shown Specifications are subject to change without notice to improve quality O O O AUTO Icons Description MENU e Open or close the onscreen display OSD menu or return to the last menu e OSD control lock Maintain the current settings or lock the OSD control to prevent unintended changes to settings To lock the OSD control press the MENU button MENU for five seconds To unlock the locked OSD
14. be used in all regions PowerSaver The power saving function of this product reduces power consumption by switching off the screen and changing the color of the power LED if the product is not used for a specified period of time The power is not turned off in power saving mode To switch the screen back on press any key on the keyboard or move the mouse Power savign mode only functions when the product is connected to a PC with a power saving function PowerSaver Normal Operation Power saving mode Power off Power button Power Indicator On Blinking off Power Consumption S22A650S 29 W S24A650S 36 W 0 5 W 0 5 W IZ The displayed power consumption level can vary in different operating conditions or when settings are changed e To reduce the power consumption to O watts turn off the power switch on the back of the product or disconnect the power cable Be sure to disconnect the power cable when you will not be using the product for an extended period of time To reduce the power consumption to O watts when the power switch is not available disconnect the power cable 9 Specifications 81 Specifications 9 3 Standard Signal Mode Table N e This product can be set to only one resolution for each screen size to obtain the optimum picture quality due to the nature of the panel Therefore a resolution other than the specified resolution may degrade the pict
15. connect a source device directly to the product and control the device from the product without having to connect the device to the PC To use the product as a USB HUB connect the product to a PC using a USB cable By gt Connect the USB cable to A on the back of the product and USB E on the PC 2 4 2 Utilizing the Product as a USB HUB Using the product as a hub connect and use various source devices with the product at the same time A PC cannot connect to multiple source devices at the same time as it has a limited number of input output ports available The HUB feature on the product will improve your work efficiency by allowing you to connect multiple source devices to the USB ports on the product at the same time without connecting them to a PC If multiple source devices are connected to the PC the many cables around the PC may look messy Connecting the devices directly to the product will resolve such inconvenience WZ gt An external mass storage HDD requires external power supply Be sure to connect it to a power source e Each port on the product supports a 100mA device Connecting and Using a Source Device 2 5 Connecting the Power Put the DC power adapter in the groove with the switch facing upward Push the adapter until you hear a click Connect the power cable to the DC power adapter Next connect the DC power adapter to the product P
16. control press the MENU button MENU for more than five seconds NG If the OSD control is locked e _ Brightness and Contrast can be adjusted and INFORMATION can be viewed e _ The function that was configured as Customized Key before locking the OSD control can be used by pressing the Eco button Preparations Icons ECO Description Configure Customized Key and press Eco The following options will be enabled ECO MAGIC Image Size A To configure Customized Key go to SETUP amp RESET Customized Key and select the mode you want alv Move to the upper or lower menu or adjust the value for an option on the OSD menu Adjust the screen brightness A Volume VOL can be adjusted if a cable is connected to the DP IN or AUDIO IN port D8 Confirm a menu selection Pressing the 9 6 button when the OSD menu is not displayed will change the input source Analog DisplayPort Digital If you power on the product or change the input source by pressing the 0 0 button a message that shows the changed input source will appear at the top left corner of the screen AUTO Press the AUTO button to automatically adjust the screen settings K e Available only in Analog mode e Changing the resolution in Display Properties will activate the Auto Adjustment function Turn the screen on or off O Power lamp The power indicator will be lit when
17. product 3 Press afv to move to Menu Transparency and press 3 on the product The following screen will appear SETUP amp RESET 4 Press a v to move to the option you want and press the 0 0 5 The selected option will be applied 6 Setup and Reset 7 6 3 Setup and Reset Language Set the menu language K e Achange to the language setting will only be applied to the onscreen menu display e It will not be applied to other functions on your PC 6 3 1 Changing the Language Press MENU on the product 2 Press a v to move to SETUP amp RESET and press on the product 3 Press a v to move to Language and press 3 on the product The following screen will appear SETUP amp RESET Deutsch English Espa ol Fran ais Italiano Magyar Polski Portugu s 4 Press a v to move to the option you want and press the 0 0 5 The selected option will be applied 6 4 Setup and Reset PC AV Mode Set PC AV Mode to AV The picture size will be enlarged This option is useful when you view a movie K PC AV Mode is only available in Digital mode 6 4 1 Configuring PC AV Mode Press MENU on the product 2 Press a v to move to SETUP amp RESET and press on the product 3 Press afv to move to PC AV Mode and press 3 on the product The following screen will appear SETUP amp RESET 4 Press afv to move to the option you want and press the 53
18. the product is operating normally K o Refer to 9 2 PowerSaver for details about the power saving function e To reduce power consumption it is best to remove the power cable when you will not be using the product for an extended period of time 1 Preparations 22 Preparations 1 2 2 Reverse Side NG The color and shape of parts may differ from what is shown Specifications are subject to change without notice to improve quality AUDIO IN Q pa e amp PC IN Description Connects to the DC power adapter Connects to a PC using a DP cable Connects to a PC via a DVI cable Connects to a PC using the D SUB cable Connects to the stereo cable Connects to an audio output device such as headphones Connect to a USB device Compatible with a USB cable version 2 0 or lower Connects to a PC via a USB cable We This port can only connect to a PC 1 Preparations 1 3 Preparations Installation 1 3 1 Attaching the Stand Place a protective cloth or Insert the stand base into the Do not remove the fixing pin until cushion on a flat surface Next stand in the direction of the you are finished attaching the place the product with the face arrow stand down on top of the cloth or cushion
19. 0 60 Hz resolution Maximum 1920 x 1080 60 Hz resolution Maximum Pixel Clock 170 MHz Power Supply This product uses 100 to 240V Refer to the label at the back of the product as the standard voltage can vary in different countries Signal connectors D sub DVI DP USB 1UP 2DOWN USB 2 0 Dimensions W x H x D Weight 512 0 x 364 0 x 216 0 mm 568 0 x 418 0 x 224 5 mm with the stand 4 2 kg 5 4 kg Environmental Operating Temperature 32 F 122 F 0 C 50 C considerations Humidity 10 96 80 96 non condensing Storage Temperature 4 F 140 F 20 C 60 C Humidity 5 90 non condensing Plug and Play This monitor can be installed and used with any Plug and Play compatible systems Two way data exchange between the monitor and PC system optimizes the monitor settings Monitor installation takes place automatically However you can customize the installation settings if desired Panel Dots Pixels Due to the nature of the manufacturing of this product approximately 1 pixel per million 1pm may appear brighter or darker on the panel This does not affect product performance WZ The above specifications are subject to change without notice to improve quality K Class B device broadcast communications device for home use 9 Specifications Fy 9 2 Specifications This Class B device designed for home use is registered for EMC requirements and can
20. 4 Changing Menu Transparency 65 Language 65 Changing the Language 66 PC AV Mode 66 Configuring PC AV Mode 67 Auto Source 67 Configuring Auto Source 68 Display Time 68 Configuring Display Time Table Of Contents 69 Key Repeat Time 69 Configuring Key Repeat Time 70 Customized Key 70 Configuring Customized Key 71 Off Timer On Off 71 Configuring Off Timer On Off 72 Off Timer Setting Ka Configuring Off Timer Setting 73 Reset T3 Initializing Settings Reset INFORMATION MENU AND 74 INFORMATION OTHERS 74 Displaying INFORMATION 74 Configuring Brightness in the Startup Screen TROUBLESHOOTING 75 Requirements Before Contacting GUIDE Samsung Customer Service Center US Testing the Product Z9 Checking the Resolution and Frequency 15 Check the followings 78 Q amp A SPECIFICATIONS so General 81 PowerSaver 82 Standard Signal Mode Table APPENDIX s4 Contact SAMSUNG WORLD WIDE 90 Correct Disposal of This Product Waste Electrical amp Electronic Equipment Table Of Contents 91 Terminology INDEX 1 1 Preparations Checking the Contents 1 1 1 Removing the Packaging 1 Open the packaging box Be careful not to damage the product when you open the packaging with a sharp instrument t Remove the Styrofoam from the product Check the components and remove the Styrofoam and plastic bag NG e The appearance of actual components may differ from the image shown e _
21. 60 023 75 029 78 750 VESA 1152 x 864 67 500 75 000 108 000 VESA 1280 x 800 49 702 59 810 83 500 VESA 1280 x 800 62 795 74 934 106 500 VESA 1280 x 960 60 000 60 000 108 000 9 Specifications 82 Specifications pesouton Freuen Fiewiany E SneFeledy kHz Hz VESA 1280 x 1024 63 981 60 020 108 000 VESA 1280 x 1024 79 976 75 025 135 000 VESA 1440 x 900 55 935 59 887 106 500 VESA 1440 x 900 70 635 74 984 136 750 VESA 1600 x 1200 75 000 60 000 162 000 VESA 1680 x 1050 65 290 59 954 146 250 VESA 1920 x 1080 67 500 60 000 148 500 Horizontal Frequency The time required to scan a single line from the left to the right side of the screen is called a horizontal cycle The reciprocal number of a horizontal cycle is called horizontal frequency Horizontal frequency is measured in kHz e Vertical Frequency Repeating the same picture dozens of times per second allows you to view natural pictures The repeat frequency is called vertical frequency or refresh rate and is indicated in Hz 9 Specifications Appendix Contact SAMSUNG WORLD WIDE A If you have any questions or comments relating to Samsung products please contact the SAMSUNG customer care center NORTH AMERICA U S A 1 800 SAMSUNG 726 7864 http www samsung com CANADA 1 800 SAMS
22. Configuring Key Repeat Time Press MENU on the product 2 Press a v to move to SETUP amp RESET and press on the product 3 Press a v to move to Key Repeat Time and press 3 on the product The following screen will appear SETUP amp RESET Acceleration 1 sec 2 sec No Repeat AUTO o e Acceleration 1 sec or 2 sec can be selected If No Repeat is selected a command responds only once when a button is pressed 4 Press a v to move to the option you want and press the 0 6 5 The selected option will be applied 6 Setup and Reset 69 Setup and Reset 6 8 Customized Key You can customize Customized Key as follows 6 8 1 Configuring Customized Key Press MENU on the product 2 Press a v to move to SETUP amp RESET and press on the product 3 Press a v to move to Customized Key and press 3 on the product The following screen will appear SETUP amp RESET 6f0 MAGIC Image Size e ECO MAGIC Image Size 4 Press a v to move to the option you want and press the 0 0 5 The selected option will be applied 6 Setup and Reset 6 9 Setup and Reset Off Timer On Off Enable or disable the off timer that automatically powers off the product 6 9 1 Configuring Off Timer On Off Press MENU on the product 2 Press a v to move to SETUP amp RESET and press on the product 3 Press afv to move to Off Timer On Off and press 3 on the prod
23. EE Connecting and Using a Source Device A If audio is supported the Volume VOL can be adjusted using the a v buttons on the front of the product 2 2 2 Driver Installation We e You can set the optimum resolution and frequency for this product by installing the corresponding EI drivers for this product e An installation driver is contained on the CD supplied with the product e Ifthe file provided is faulty visit the Samsung homepage http www samsung com and download the file Insert the user manual CD provided with the product into the CD ROM drive Click Windows Driver Follow the instructions given on the screen to proceed with installation KR N ra Select your product model from the list of models Select the display adapter on which you want to intall he monitor Select the monitor which you wam to install 5 Go to Display Properties and check that the resolution and refresh rate are appropriate Refer to your Windows OS manual for further details Connecting and Using a Source Device 2 2 3 Setting Optimum Resolution An information message about setting optimum resolution will appear if you power on the product for the first time after purchase Select a language and change the resolution to the optimum value The optimal resolution for this monitor is as follows Follow the above settings to set the resolution a English 1 Press a v to move to the language you want and pr
24. I port on the PC 2 Connect the stereo cable to the AUDIO IN port on the back of the product and the AUDIO OUT port on the PC Connecting and Using a Source Device 3 Connect the DC power adapter to the product and a power socket and turn on the power switch on the PC For details refer to 2 5 Connecting the Power 4 Press 0 6 to change the input source to Digital A e Audio is not available if the PC and product are connected via the DVI port e Refer to 2 3 Connecting Headphones for details on how to enable sound Connection Using an HDMI DVI Cable Connect the DVI cable to the DVI IN port on the back of the product and the HDMI port on the PC 2 Connect the DC power adapter to the product and a power socket and turn on the power switch on the PC For details refer to 2 5 Connecting the Power 3 Press 3 to change the input source to Digital A e Audio is not available if the PC and product are connected via the DVI port Refer to 2 3 Connecting Headphones for details on how to enable sound Connection Using the DP Cable Connect the DP cable to the DP IN port on the back of the product and the DP port on the PC 2 Connect the DC power adapter to the product and a power socket and turn on the power switch on the PC For details refer to 2 5 Connecting the Power 3 Press 3 to change the input source to DisplayPort 2 Connecting and Using a Source Device
25. MSUNG 726 7864 http www samsung com LATVIA 8000 7267 http www samsung com LITHUANIA 8 800 77777 http www samsung com LUXEMBURG 261 03 710 http www samsung com MACEDONIA 023 207 777 http www samsung com MONTENEGRO 020 405 888 http www samsung com NETHERLANDS 0900 SAMSUNG http www samsung com 0900 7267864 0 10 Min NORWAY 815 56480 http www samsung com POLAND 0 801 1SAMSUNG 172 678 http www samsung com 48 22 607 93 33 PORTUGAL 808 20 SAMSUNG 808 20 7267 http www samsung com RUMANIA 08008 SAMSUNG 08008 726 http www samsung com 7864 TOLL FREE No SERBIA 0700 Samsung 0700 726 7864 http www samsung com SLOVAKIA 0800 SAMSUNG 0800 726 786 http www samsung com SPAIN 902 1 SAMSUNG 902 172 678 http www samsung com Appendix 86 Appendix EUROPE SWEDEN 0771 726 7864 SAMSUNG http www samsung com SWITZERLAND 0848 SAMSUNG http www samsung com ch 7267864 CHF 0 08 min German http www samsung com ch_fr French U K 0330 SAMSUNG 7267864 http www samsung com CIS ARMENIA 0 800 05 555 http www samsung com AZERBAIJAN 088 55 55 555 http www samsung com BELARUS 810 800 500 55 500 http www samsung com GEORGIA 0 800 555 555 http www samsung com KAZAKHSTAN 8 10 800 500 55 500 http www samsung com GSM 7799 KYRGYZSTAN 00 800 500 55 500 http www samsung com MOLDOVA 0 800 614 40 http ww
26. RAN 021 8255 http www samsung com JORDAN 800 22273 http www samsung com 065777444 KUWAIT 183 2255 http www samsung com ae English http www samsung com ae_ar Arabic Appendix Appendix MIDDIE EAST MOROCCO 080 100 2255 http www samsung com OMAN 800 SAMSUNG 726 7864 http www samsung com ae English http www samsung com ae_ar Arabic SAUDI ARABIA 9200 21230 http www samsung com ae English http www samsung com ae_ar Arabic TURKEY 444 77 11 http www samsung com U A E 800 SAMSUNG 726 7864 http www samsung com AFRICA ANGOLA 91 726 7864 http www samsung com BOTSWANA 0800 726 000 http www samsung com CAMEROON 7095 0077 http www samsung com COTE D IVOIRE 8000 0077 http www samsung com GHANA 0800 10077 http www samsung com 0302 200077 KENYA 0800 724 000 http www samsung com NAMIBIA 8197267864 http www samsung com NIGERIA 0800 726 7864 http www samsung com SENEGAL 800 00 0077 http www samsung com SOUTH AFRICA 0860 SAMSUNG 726 7864 http www samsung com TANZANIA 0685 88 99 00 http www samsung com UGANDA 0800 300 300 http www samsung com ZAMBIA 211350370 http www samsung com Appendix 89 Appendix Correct Disposal of This Product Waste Electrical amp Electronic Equipment pA Applicable in countries with separate collection systems This marki
27. Source Device 2 1 Before Connecting SAMSUNG 2 1 1 Pre connection Checkpoints e Before connecting a source device read the user manual provided with it The number and locations of ports on source devices may differ from device to device e _ Do not connect the power cable until all connections are completed Connecting the power cable during connection may damage the product e Check the types of ports at the back of the product you want to connect 2 2 Connecting and Using a Source Device Connecting and Using a PC 2 2 1 Connecting to a PC e Select a connection method suitable for your PC LE Connecting parts may differ in different products Connection using the D SUB cable analogue type 7 Connect the D SUB cable to the RGB IN port on the back of the product and the RGB port on the PC 2 Connect the stereo cable to the AUDIO IN port on the back of the product and the AUDIO OUT port on the PC 3 Connect the DC power adapter to the product and a power socket and turn on the power switch on the PC For details refer to 2 5 Connecting the Power 4 Press 3 to change the input source to Analog A e Audio is not available if the PC and product are connected via the D SUB port e Refer to 2 3 Connecting Headphones for details on how to enable sound Connection Using the DVI Cable 7 Connect the DVI cable to the DVI IN port on the back of the product and the DV
28. UNG 726 7864 http www samsung com ca English http www samsung com ca_fr French MEXICO 01 800 SAMSUNG 726 7864 http www samsung com LATIN AMERICA ARGENTINE 0800 333 3733 http www samsung com BOLIVIA 800 10 7260 http www samsung com BRAZIL 0800 124 421 http www samsung com 4004 0000 CHILE 800 SAMSUNG 726 7864 http www samsung com From mobile 02 482 82 00 COLOMBIA 01 8000112112 http www samsung com COSTA RICA 0 800 507 7267 http www samsung com latin Spanish http www samsung com latin_en English DOMINICA 1 800 751 2676 http www samsung com latin Spanish http www samsung com latin_en English ECUADOR 1 800 10 7267 http www samsung com latin Spanish http www samsung com latin_en English EL SALVADOR 800 6225 http www samsung com latin Spanish http www samsung com latin_en English Appendix 84 Appendix LATIN AMERICA GUATEMALA 1 800 299 0013 http www samsung com latin Spanish http www samsung com latin_en English HONDURAS 800 27919267 http www samsung com latin Spanish http www samsung com latin_en English JAMAICA 1 800 234 7267 http www samsung com NICARAGUA 00 1800 5077267 http www samsung com latin Spanish http www samsung convlatin en English PANAMA 800 7267 http www samsung com latin Spanish http www samsung com latin_en English PERU 0 800 777 08 http
29. ct Disposal of This Product Waste Electrical amp Electronic Equipment 90 Correct posture to use the product 13 Customized Key 70 D Display Time 68 ECO 56 F Fine 46 G Gamma 52 General 80 Green 49 Image Size 53 INFORMATION 74 Installation 24 K Key Repeat Time 69 L Languagey 65 M MAGIC 40 MagicRotation Auto 28 Menu Transparency 64 O Off Timer On Off 71 Off Timer Setting 72 P Parts 21 PC AV Mode 66 PowerSaver 81 Q Q amp A78 Index R Red 48 Requirements Before Contacting Samsung Customer Service Center 75 Reset 73 Response Time 47 S Safety Precautions 6 Sharpness 44 Standard Signal Mode Table 82 T Terminology 91
30. e Troubleshooting Guide Sound issue The volume is too low Adjust the volume If the volume is still low after turning it up to the maximum level adjust the volume on your PC sound card or software program Source device issue A beeping sound is heard when my PC is booting If a beeping sound is heard when your PC is booting have your PC serviced 8 2 Troubleshooting Guide Q amp A Question Answer How can change the frequency Set the frequency on your graphics card Windows XP Select Control Panel gt Appearance and Themes Display Settings Advanced Monitor and adjust Refresh rate under Monitor settings Windows ME 2000 Select Control Panel gt Display gt Settings gt Advanced Monitor and adjust Refresh rate under Monitor settings Windows Vista Select Control Panel Appearance and Personalization Personalization Display Settings Advanced Settings Monitor and adjust Refresh rate under Monitor settings Windows 7 Select Control Panel gt Appearance and Personalization Display gt Screen Resolution gt Advanced settings Monitor and adjust Refresh rate under Monitor settings 8 Troubleshooting Guide Troubleshooting Guide Question Answer How can change the resolution Windows XP Go to Control Panel gt Appearance and Themes Display Settings and adjust
31. e product KR N ra If the Check Signal Cable message appears the product is working normally NG If the screen remains blank check the PC system video controller and cable 8 1 2 Checking the Resolution and Frequency For a mode that exceeds the supported resolution refer to 9 3 Standard Signal Mode Table the message Not Optimum Mode will appear for a short time 8 1 3 Check the followings Installation issue PC mode The screen keeps switching on and off Check the cable connection between the product and PC and ensure the connection is secure Refer to 2 2 Connecting and Using a PC Screen issue The power LED is off The screen will not switch Check that the power cable is connected on correctly Refer to 2 2 Connecting and Using a PC The message Check Signal Cable appears Check that the cable is properly connected to the product Refer to 2 2 Connecting and Using a PC Check that the device connected to the product is powered on Troubleshooting Guide Screen issue Not Optimum Mode is displayed This message appears if the signal from the graphics card exceeds the maximum resolution or frequency for the product Change the maximum resolution and frequency to suit the product performance referring to Standard Signal Mode Table page 82 The images on the screen look distorted Check the cable connection to the product Refer to 2 2 C
32. e product e The product or heavy objects may fall as children try to reach for the toy or sweets resulting in a serious injury Before Using the Product 9 Before Using the Product During a lightning or thunderstorm power off the product and remove the power cable e An electric shock or fire may result Do not drop objects on the product or apply impact e An electric shock or fire may result Do not move the product by pulling the power cord or any cable e Otherwise the power cable may be damaged and product failure an electric shock or fire may result If a gas leakage is found do not touch the product or power plug Also ventilate the area immediately e Sparks can cause an explosion or fire e During a lightning or thunderstorm do not touch the power cord or antenna cable Do not lift or move the product by the power cord or any cable e Otherwise the power cable may be damaged and product failure an electric shock or fire may result Do not use or keep combustible spray or an inflammable substance near the product e An explosion or fire may result Ensure the vents are not blocked by tablecloths or curtains e Otherwise a fire may result from an increased internal temperature Before Using the Product Do not inser
33. ed 6 Setup and Reset 58 Setup and Reset Configuring Sensitivity A Q N ra Press MENU on the product Press a v to move to SETUP amp RESET and press 53 on the product Press a v to move to ECO and press on the product Press a v to move to Sensitivity and press on the product The following screen will appear e High High sensitivity that maximizes the varying level of screen brightness depending on the ambient light intensity e Medium Intermediate sensitivity that sets a varying level of screen brightness between High and Low depending on the ambient light intensity e Low Low sensitivity that minimizes the varying level of screen brightness depending on the ambient light intensity Press a v to move to the option you want and press the 3 The selected option will be applied 6 Setup and Reset ET Setup and Reset Configuring Brightness Level A N ra Press MENU on the product Press a v to move to SETUP amp RESET and press 53 on the product Press a v to move to ECO and press on the product Press a v to move to Brightness Level and press on the product The following screen will appear Brighter Current Dimmer e Brighter Increase the current brightness of the screen e Current Maintain the current brightness of the screen e Dimmer Decrease the current brightness of the screen Press a v to move to the option
34. een regardless of the aspect ratio of the input source SIZE amp POSITION e 4 3 Display the picture with an aspect ratio of 4 3 Suitable for videos and standard broadcasts e 16 9 Display the picture with an aspect ratio of 16 9 Suitable for DVD content or widescreen broadcasts e Screen Fit Display the picture with the original aspect ratio without cutting off NG Requirements to activate Image Size e When connecting to digital output device via DVI DP cable e When signal resolution is 480p 576p 720p 1080i 1080p Press a v to move to the option you want and press the 5 6 The selected option will be applied 5 Resizing or Relocating the Screen 53 5 2 Resizing or Relocating the Screen H Position amp V Position H Position Move the screen to the left or right V Position Move the screen up or down Wg Available only when Image Size is set to Screen Fit e Only available in Analog mode 5 2 1 Configuring H Position amp V Position Press MENU on the product 2 Press a v to move to SIZE amp POSITION and press 53 on the product 3 Press a v to move to H Position or V Position and press 3 The following screen will appear SIZE amp POSITION SIZE amp POSITION 4 Press a v to configure H Position or V Position 5 Resizing or Relocating the Screen 54 5 3 Resizing or Relocating the Screen Menu H Position amp Menu V Position Menu H Position Mo
35. en Adjusting the brightness brightens the whole screen but adjusting Gamma only brightens the medium brightness Grey scale Scale refers to levels of color intensity that show variations of color change from darker areas to brighter areas on the screen Changes to the screen brightness are expressed with black and white variation and grey scale refers to the medium area between black and white Changing the grey scale through Gamma adjustment will change the medium brightness on the screen Scanning rate Scanning rate or refresh rate refers to the frequency of screen refreshes Screen data is transmitted as it refreshes to display an image although the refreshing is invisible to the naked eye The number of screen refreshes is called scanning rate and is measured in Hz A scanning rate of 60Hz means that the screen refreshes 60 times per second The screen scanning rate depends on the performance of the graphics cards in your PC and monitor Horizontal Frequency Characters or images displayed on the monitor screen consist of numerous dots pixels Pixels are transmitted in horizontal lines which are then arranged vertically to create an image The horizontal frequency is measured in KHz and represents how many times horizontal lines per second are transmitted and displayed on the monitor screen A horizontal frequency of 85 means that the horizontal lines that make up an image are transmitted 85 000 times per second and the horizontal f
36. erwise a fire may result S Before Using the Product EIE Before Using the Product Do not let water enter the DC power device or get the device wet e An electric shock or fire may result e Avoid using the product outdoors where it can be exposed to rain or snow e Becareful not to get the DC power adapter wet when you wash the floor Do not put the DC power adapter near to any heating apparatus e Otherwise a fire may result Keep the DC power adapter in a well ventilated area Looking at the screen too close for an extended period of time can deteriorate your eyesight Do not hold the monitor upside down or move it by holding the stand e The product may fall and break or cause a personal injury Do not use humidifiers or stoves around the product e An electric shock or fire may result Rest your eyes for more than 5 minutes for every 1 hour of product use e Eye fatigue will be relieved Do not touch the screen when the product has been turned on for an extended period of time as it will become hot Store the small accessories used with the product out of reach of children Before Using the Product Exercise caution when adjusting the product angle or stand height e Otherwise children s fingers or hands may become stuck and injured e Tilting the product excessively may cause i
37. ess the I 2 To hide the information message press MENU WG e Ifthe optimum resolution is not selected the message will appear up to three times for a specified time even when the product is turned off and on again e _ The optimum resolution can also be selected in Control Panel on your PC 2 Connecting and Using a Source Device 831 Connecting and Using a Source Device 2 2 4 Changing the Resolution Using a PC K e Adjust the resolution and refresh rate in Control Panel on your PC to obtain optimum picture quality e The picture quality of TFT LCDs may degrade if the optimum resolution is not selected Changing the Resolution on Windows XP Go to Control Panel Display Settings and change the resolution Mi ee Pa Th Mm o O B Pia Drum M em conve OF carena Parat lig g N K3 5 je jtej v je iG lr ilo ie N isiie to mie ete ls e i ib ie is i Display Properties Themes Desktop Screen Saver Appearance Seling Drag the monitor icons to match the physical anangement of your monitors Display 1 anannenene Screen tesolution Color quality les J More Highest 32 ba seins by eee pivele a inia Yi Use this device at the primary moniter Extend my Windows desktop onto this monitor Connecting and Using a Source Device Changing the Resolution on Windows Vista Go to Control Panel Personalization Display Settings and change the resolutio
38. ide Mm Press a v to move to the option you want and press the 3 O The selected option will be applied Notes Eco Motion Sensor Activated Power Off 10 sec e Ifthe monitor is left idle for the period of time to which the off timer is configured when Eco Motion Sensor is enabled Eco Motion Sensor will activate and switch the monitor to power saving mode e A 10 second countdown timer will start along with the above picture before the power saving mode activates showing the operation status of the Eco Motion Sensor Eco Light Sensor Activated Eco Light Sensor Activated e _ If the screen brightness is adjusted according to the ambient light intensity when the Eco Light Sensor is on a pop up as shown above will appear showing the adjusting screen brightness e Ifthe screen becomes brighter as the ambient light becomes brighter the brightness slide bar level will increase with a sun image displayed If the screen becomes darker the brightness slide bar level 6 Setup and Reset 62 Setup and Reset will decrease with amoon image displayed The brightness slide bar will be displayed for 3 seconds after the sensor activates You ve saved tree s A pop up as shown above will appear when an energy tree completes while Eco Icon Display is On NG If the above picture is displayed it means the Eco Icon Display option is On Change this setting to Off if you do not want to display the pop up The amount
39. isplayed in the language of the operating system This complies with the basic policies of Windows Caution Compatible only with Windows 7 32 bits or 64 bits 2 Compatible with a graphics card that complies with the DDC CI and MS API standards With a graphics card that does not comply with the aforementioned standards the MagicRotation Auto function may not be available 3 To maximize the performance of the function update the graphics card driver to the latest version 4 Fourteen languages are available as installation languages English Fran ais Deutsch Magyar Italiano Polski Portugu s Pycekun Espa ol Svenska T rk e RAE NE 5210 5 Ifthe orientation is set to a mode other than Landscape in the screen resolution menu on Windows 7 the MagicRotation Auto function may not work properly 6 The OSD menu will be displayed if the monitor is rotated When the monitor is rotated the screen reconfiguration process may be displayed or screen burn in may appear depending on the graphics card This is performed by the Windows operating system and has nothing to do with the product If you do not want the screen to rotate automatically when the monitor is rotated press the Windows and L keys at the same time to lock the Windows operating system If the operating system cannot be locked it is due to the constraints of Windows API and has nothing to do with the product 1 Preparations 28 Connecting and Using a
40. lug in the power cable to the power socket Removing the DC power adapter To remove the DC power adapter lift it outwards from the bottom as shown in the image L A When using the adapter without fixing it to the back of the monitor the adapter jack can easily get disconnected or the cable may break Be sure to securely fix the adapter in the groove Screen Setup Configure the screen settings such as brightness and color tone 3 1 MAGIC This feature provides the viewing angle brightness and tint to suit your preferences 3 1 1 SAMSUNG MAGIC Bright This menu provides an optimum picture quality suitable for the environment where the product will be used A This menu is not available when Eco Light Sensor or Eco Saving is set to On Configuring 4 jeBright Press MENU on the product Press a v to move to PICTURE and press 0 6 on the product Press a v to move to MAGIC and press 5 6 on the product KR b Press a v to move to i icBright and press 2 6 on the product The following screen will appear Custom Standard Game Cinema Dynamic Contrast e Custom Customize the contrast and brightness as required e Standard Obtain a picture quality suitable for editing documents or using Internet e Game Obtain a picture quality suitable for playing games that involve many graphic effects and dynamic movements e Cinema Obtain the b
41. mode 3 4 1 Configuring Sharpness Press MENU on the product 2 Press a v to move to PICTURE and press 53 on the product 3 Press a v to move to Sharpness and press 3 on the product The following screen will appear PICTURE Y v 4 Adjust the Sharpness using the a v button 3 5 Screen Setup Coarse Vertical noise stripes on the screen will be removed The screen may be moved after changing the frequency Coarse If this is the case move the screen to the center using the H Position adjustment menu K Only available in Analog mode 3 5 1 Adjusting Coarse Press MENU on the product 2 Press a v to move to PICTURE and press 53 on the product 3 Press afv to move to Coarse and press 9 amp on the product The following screen will appear PICTURE 4 Adjust the Coarse using the a v button 3 Screen Setup 45 3 6 Screen Setup Fine Horizontal noise stripes on the screen will be removed If the noise is not completely removed after adjusting the Fine value adjust Coarse and try Fine adjustment again A Only available in Analog mode 3 6 1 Adjusting Coarse Press MENU on the product 2 Press a v to move to PICTURE and press 53 on the product 3 Press afv to move to Fine and press 3 on the product The following screen will appear PICTURE 4 Adjust the Fine using the a v button 3 Screen Setup KI
42. n a Windows Live Messenger H2 22 B Windows DVD Maker a Windows Meeting Space Y sga gt 9522 IE NG MER TOL AE EBONY NOR 7NA BE NOS AGO CE mee 4 Be 22710 NG EEE CSO NG BOS NSE NU ZIBUN mE ZEE BBA St DHSS NEHA SE SF NG DAA UEU BABOY HUH LIC VE WY ASS UB UN DONT RSET SESS BUG SUR enpug DEAS ARSE HERG EEO A PES 32 za SIE BSE gt NG AO E SO SABUC GO Afp OS KA NG ware DY gat Be H 2A DRA DOK FOIE ANAY LAS m BO MANG Bey pi gagao szw DUH FUSE ZEHN HEN HANE BE Se paayan e ze UG 2UG FERNE 28 MSIE SEE NG ana NAG ec Aga se hehe eee ee PETS HEB we ttrt r BE NAGO agan KO n oF TIL Connecting and Using a Source Device Changing the Resolution on Windows 7 Go to Control Panel Display Screen Resolution and change the resolution o x Remote Desktop Connection i p KAY oa lsrp Seonn Confer U 2 Microsoft Word 2010 Adjust your computer s settings View bye Lange icons Wireless Di Mi z a rer gt ai oe OBEN etault Pr d y Action Center Fa Administrative Tools EF Microsoft Office Excel 2007 pan Wg Autoplay Backup and Restore SX BitLocker Drive Encryption Gi Color Management a Credential Manager Pat Date and Time Search programs and files gt velauk Programs GR Desktop Gadgets 4 Device Manager aig Devices and Printers BM Display S Ease of Access Center es CG E gt Control Panel gt All Control Panel items Display
43. ng on the product accessories or literature indicates that the product and its electronic accessories e g charger headset USB cable should not be disposed of with other household waste at the end of their working life To prevent possible harm to the environment or human health from uncontrolled waste disposal please separate these items from other types of waste and recycle them responsibly to promote the sustainable reuse of material resources Household users should contact either the retailer where they purchased this product or their local government office for details of where and how they can take these items for environmentally safe recycling Business users should contact their supplier and check the terms and conditions of the purchase contract This product and its electronic accessories should not be mixed with other commercial wastes for disposal Appendix Terminology OSD On Screen Display On screen display OSD allows you to configure on screen settings to optimize the picture quality as required It allows you to change the screen brightness tint size and many other settings using menus displayed on the screen HUB HUB refers to a device that is acommon connection point for multiple devices connected over a network It is used to connect multiple PCs video devices office devices and or LANs over a single network Gamma The Gamma menu adjusts the grey scale that represents middle tones on the scre
44. of energy saved by the Eco Motion Sensor Eco Light Sensor and Eco Saving functions will accumulate and the progress can be viewed as a growing energy tree NG The energy tree grows as the energy savings of the monitor accumulate Accordingly the tree s growth will also be affected by other functions that involve power consumption such as the brightness control function The amount of energy savings accumulated by using the power saving functions such as Eco Motion Sensor Eco Light Sensor and Eco Saving will be calculated and represented as an amount of carbon dioxide A complete energy tree will be displayed when the amount of energy savings accumulates to as much as the amount of carbon dioxide a tree absorbs in a year This shows that your energy saving is as effective as planting a tree so that you can easily understand the accumulation of energy savings over time and its effect by viewing the progress of a tree growing The progress of a tree growing will be represented as 10 different images stages After one full grown tree is complete the initial image will be restored and the number of trees will continue to accumulate The number for energy trees will be rounded to one decimal place 6 Setup and Reset 63 6 2 Setup and Reset Menu Transparency Set the transparency for the menu windows 6 2 1 Changing Menu Transparency Press MENU on the product 2 Press a v to move to SETUP amp RESET and press on the
45. onnecting and Using a PC The screen is not clear The screen is blurry Adjust Coarse page 45 and Fine page 46 Remove any accessories video extension cable etc and try again Set the resolution and frequency to the recommended level Refer to 9 1 General The screen appears unstable and shaky There are shadows or ghost images left on the screen Check that the resolution and frequency for the PC are within the range of resolution and frequency compatible with the product and if required change the settings referring to Standard Signal Mode Table page 82 in this manual and the INFORMATION menu on the product The screen is too bright The screen is too dark Adjust Brightness page 42 and Contrast page 43 Screen color is inconsistent Change the COLOR settings Refer to Configuring Tint The colors on the screen have a shadow and are distorted Change the COLOR settings Refer to Configuring Tint White does not really look white Change the COLOR settings Refer to Configuring Tint There is no image on the screen and the power LED blinks every 0 5 to 1 second The product is in power saving mode Press any key on the keyboard or move the mouse to return to the previous screen Sound issue There is no sound Check the connection of the audio cable or adjust the volume Check the volume 8 Troubleshooting Guid
46. or green in the picture Range 0 100 A higher value will increase the intensity of the color Wg This menu is not available when fen GicColor is in Full or Intelligent mode a 4 2 1 Configuring Green Press MENU on the product 2 Press a v to move to COLOR and press 9 on the product 3 Press a v to move to Green and press 3 on the product The following screen will appear 4 Adjust the Green using the a v button 4 Configuring Tint 49 4 3 Configuring Tint Blue Adjust the value of the color blue in the picture Range O 100 A higher value will increase the intensity of the color Wg This menu is not available when fen GicColor is in Full or Intelligent mode 4 3 1 Configuring Blue Press MENU on the product 2 Press a v to move to COLOR and press 9 on the product 3 Press a v to move to Blue and press 9 amp on the product The following screen will appear 4 Adjust the Blue using the a v button 4 Configuring Tint 50 4 4 Configuring Tint Color Tone Adjust the general color tone of the picture This menu is not available when WAG cCOlor is in Full or Intelligent mode 4 41 Configuring the Color Tone Settings Press MENU on the product 2 Press a v to move to COLOR and press 3 on the product 3 Press afv to move to Color Tone and press 3 on the product The following screen will appear Cool 2 Cool 1 N
47. ormal Warm 1 Warm 2 Custom Cool 2 Set the color temperature to be cooler than Cool 1 Cool 1 Set the color temperature to be cooler than Normal mode Normal Display the standard color tone Warm 1 Set the color temperature to be warmer than Normal mode Warm 2 Set the color temperature to be warmer than Warm 1 Custom Customize the color tone Press a v to move to the option you want and press the 5 0 The selected option will be applied 4 Configuring Tint 51 Configuring Tint 45 Gamma Adjust the mid range brightness Gamma of the picture 4 5 1 Configuring Gamma Press MENU on the product 2 Press a v to move to COLOR and press 3 on the product 3 Press a v to move to Gamma and press 3 on the product The following screen will appear KI LY 4 AUTO O v Y y r v 4 Press a v to move to the option you want and press the 0 6 5 The selected option will be applied 4 Configuring Tint 52 5 1 Resizing or Relocating the Screen Image Size Change the picture size 5 1 1 Changing the Image Size 1 2 Press MENU on the product Press a v to move to SIZE amp POSITION and press 3 on the product Press a v to move to Image Size and press 3 on the product The following screen will appear SIZE amp POSITION e Auto Display the picture according to the aspect ratio of the input source e Wide Display the picture in full scr
48. personal injury Installing the product in an unusual place a place exposed to a lot of fine particles chemical substances or extreme temperatures or an airport or train station where the product should operate continuously for an extended period of time may seriously affect its performance e Be sure to consult Samsung Customer Service Center page 84 before installation if you want to install the product at such a place High voltage runs through the product Do not attempt to disassemble repair or modify the product on your own e An electric shock or fire may result e Contact Samsung Customer Service Center page 84 for repair Before moving the product turn off the power switch and disconnect the power cable and all other connected cables e Otherwise the power cord may be damaged and a fire or electric shock may result If the product generates a strange noise a burning smell or smoke remove the power cord immediately and contact Samsung Customer Service Center page 84 An electric shock or fire may result Do not let children hang from the product or climb on top of it e The product may fall and your child may become injured or seriously harmed If the product falls or the exterior is damaged power off the product remove the power cord and contact Samsung Customer Service Center page 84 e Otherwise an electric shock or fire may result Do not put a heavy object toy or sweets on top of th
49. r fire may result Remove foreign substances such as dust around the plug pins and power socket with a dry cloth e Otherwise a fire may result Before Using the Product A Caution NG Installation A Warning Do not unplug the power cord when the product is in use e The product may become damaged by an electric shock Do not use the power cord for products other than authorized products supplied by Samsung e An electric shock or fire may result Keep the power socket where the power cord is connected unobstructed e If any problem occurs in the product unplug the power cable to completely cut the power to the product Power to the product cannot be completely cut off with the power button Hold the plug when disconnecting the power cord from the power socket e An electric shock or fire may result DO NOT PLACE CANDLES INSECT REPELLANTS OR CIGARETTES ON TOP OF THE PRODUCT DO NOT INSTALL THE PRODUCT NEAR HEAT SOURCES e Otherwise a fire may result Avoid installing the product in a narrow space with bad ventilation such as a bookshelf or wall closet e Otherwise a fire may result due to an increased internal temperature Keep the plastic packaging bag for the product in a place that cannot be reached by children e Children may suffocate Before Using the Product
50. requency is indicated in 85kHz Appendix CE Appendix Vertical Frequency One image is made of numerous horizontal lines The vertical frequency is measured in Hz and represents how many images can be created per second by those horizontal lines A vertical frequency of 60 means that an image is transmitted 60 times per second The vertical frequency is also called refresh rate and affects screen flicker Resolution Resolution is the number of horizontal pixels and vertical pixels that form a screen It represents the level of display detail A higher resolution displays a greater amount of information on the screen and is suitable for performing multiple tasks at the same time E g A resolution of 2560 x 1440 consists of 2 560 horizontal pixels horizontal frequency and 1 440 vertical lines vertical resolution Plug amp Play The Plug amp Play feature allows the automatic exchange of information between a monitor and PC to produce an optimum display environment The monitor uses VESA DDC international standard to execute Plug amp Play Index A Auto Source 67 B Before Connecting 29 Blue 50 Brightness 42 C Checking the Contents 19 Cleaning 4 Coarse 45 Color Tone 51 Configuring Brightness in the Startup Screen 74 Connecting and Using a PC 30 Connecting Headphones 37 Connecting the Product to aPC as a USB HUB 38 Contact SAMSUNG WORLDWIDE 84 Contrast 43 Copyright 2 Corre
51. rightness and sharpness of TVs suitable for enjoying video and DVD content e Dynamic Contrast Obtain balanced brightness through automatic contrast adjustment 5 Press a v to move to the option you want and press the 3 6 The selected option will be applied Screen Setup 3 1 2 SAMSUNG MAGIC Color MAGIGColor is a new picture quality improvement technology developed independently by Samsung which delivers vivid natural colors without picture quality degradation A This menu is not available when WAG cBright is in Cinema or Dynamic Contrast mode Configuring yac ccolor Press MENU on the product Press a v to move to PICTURE and press 29 6 on the product Press a v to move to MAGIC and press 7 8 on the product KR Q N ra Press a v to move to AG cColor and press 0 8 on the product The following screen will appear Of Demo Full Intelligent e Off Disable fr GicColor e Demo Compare normal screen mode with svsensc olor mode MAGIC e Full Obtain a vivid picture quality for all areas including the flesh colors in the picture e Intelligent Improve the chroma for all areas except the flesh colors in the picture 5 Press a v to move to the option you want and press the 0 6 6 The selected option will be applied 3 2 Screen Setup Brightness Adjust the general brightness of the picture Range 0 100 A higher value will make the picture appear brighter
52. s not detected any movement of an object or person for 5 minutes within the specified range of detection 10 Min Automatically turn off the power if the sensor has not detected any movement of an object or person for 10 minutes within the specified range of detection 20 Min Automatically turn off the power if the sensor has not detected any movement of an object or person for 20 minutes within the specified range of detection 30 Min Automatically turn off the power if the sensor has not detected any movement of an object or person for 30 minutes within the specified range of detection 1 h Automatically turn off the power if the sensor has not detected any movement of an object or person for 1 hour within the specified range of detection 5 Press afv to move to the option you want and press the 53 6 The selected option will be applied 6 Setup and Reset 56 Setup and Reset Configuring Backlight A Q N x lt Press MENU on the product Press a v to move to SETUP amp RESET and press 53 on the product Press a v to move to ECO and press on the product Press a v to move to Backlight and press 3 on the product The following screen will appear NOR Dimming e Off Turn off the screen and activate DPMS mode If Off is selected it takes several seconds for the monitor to detect movement and turn on after it turned off e Dimming Reduce the brightness of the screen
53. stalling a Wall mount Kit or Desktop Stand Anti theft Lock MagicRotation Auto Before Connecting Pre connection Checkpoints Table Of Contents 30 30 32 33 34 37 38 38 38 39 SCREEN SETUP 40 40 41 42 42 43 43 44 44 45 45 46 46 47 47 CONFIGURING TINT 48 48 49 49 Connecting and Using a PC Connecting to a PC Driver Installation Setting Optimum Resolution Changing the Resolution Using a PC Connecting Headphones Connecting the Product to a PC asa USB HUB Connecting a PC to the Product Utilizing the Product as a USB HUB Connecting the Power MAGIC SAMSUNG MAGIC Bright SAMSUNG MAGIC Color Brightness Configuring Brightness Contrast Configuring Contrast Sharpness Configuring Sharpness Coarse Adjusting Coarse Fine Adjusting Coarse Response Time Configuring Response Time Red Configuring Red Green Configuring Green Table Of Contents 50 Blue 50 Configuring Blue 51 Color Tone Sil Configuring the Color Tone Settings 52 Gamma 52 Configuring Gamma RESIZING OR 53 Image Size RELOCATING THE SCREEN 54 H Position amp V Position 54 Configuring H Position amp V Position ol 3 Changing the Image Size 55 Menu H Position amp Menu V Position 95 Configuring Menu H Position amp Menu V Position SETUP AND RESET 56 Eco 56 Eco Motion Sensor 58 Eco Light Sensor 61 Eco Saving 62 Eco Icon Display 64 Menu Transparency 6
54. sure you purchase a wall mount kit that can be installed 10cm or farther away from the wall e Be sure to use a wall mount kit that complies with the standards 1 3 5 Anti theft Lock An anti theft lock allows you to use the product securely even in public places The locking device shape and locking method depend on the manufacturer Refer to the user guide provided with your anti theft locking device for details The lock device is sold separately To lock an anti theft locking device Fix the cable of your anti theft locking device to a heavy object such as a desk 2 Put one end of the cable through the loop on the other end 3 Insert the locking device into the anti theft lock slot at the back of the product 4 Lock the locking device A e An anti theft locking device can be purchased separately e _ Refer to the user guide provided with your anti theft locking device for details e Anti theft locking devices can be purchased at electronics retailers or online 1 Preparations 1 4 Preparations MagicRotation Auto The MagicRotation Auto function detects the rotation of monitors that are fitted with a rotation sensor and rotates the Windows screen accordingly Software Installation 7 Insert the user manual CD provided with the product into the CD ROM drive 2 Follow the instructions given on the screen to proceed with installation K After installation the on screen display OSD menu will be d
55. t a metallic object a chopstick coin hair pin etc or inflammable object paper match etc into the vent or ports of the product e If water or any foreign substance enters the product be sure to power off the product remove the power cord and contact Samsung Customer Service Center page 84 e Product failure an electric shock or fire may result Do not place objects containing liquid vases pots bottles etc or metallic objects on top of the product e If water or any foreign substance enters the product be sure to power off the product remove the power cord and contact Samsung Customer Service Center page 84 e Product failure an electric shock or fire may result Leaving the screen fixed on a stationary image for an extended period of time may cause afterimage burn in or defective pixels e If you are not going to use the product for an extended period of time activate power saving mode or a moving picture screen saver Disconnect the power cord from the power socket if you do not plan on using the product for an extended period of time vacation etc e Otherwise a fire may result from accumulated dust overheating an electric shock or electric leakage Use the product at the recommended resolution and frequency e Your eyesight may deteriorate Do not put DC power adapters together e Otherwise a fire may result Remove the plastic bag from the DC power adapter before you use it NG e Oth
56. t to fall and result in personal injury Do not place heavy objects on the product e Product failure or personal injure may result Correct posture to use the product Use the product in the correct posture as follows e Straighten your back Allow a distance of 45 to 50cm between your eye and the screen and look slightly downward at the screen Keep your eyes directly in front of the screen e Adjust the angle so light does not reflect on the screen e _ Keep your forearms perpendicular to your upper arms and level with the back of your hands e Keep your elbows at about a right angle e Adjust the height of the product so you can keep your knees bent at 90 degrees or more your heels attached to the floor and your arms lower than your heart Table Of Contents BEFORE USING THE PRODUCT PREPARATIONS CONNECTING AND USING A SOURCE DEVICE O N DQ O OO NN Ow N mah o 19 20 21 21 23 24 24 25 25 26 27 28 29 Copyright Icons used in this manual Symbols for safety precautions Cleaning Cleaning Securing the Installation Space Precautions for storage Safety Precautions Electricity and Safety Installation Operation Correct posture to use the product Checking the Contents Removing the Packaging Checking the Components Parts Frontal Buttons Reverse Side Installation Attaching the Stand Adjusting the Product Tilt and Height Rotating the Monitor In
57. the resolution Windows ME 2000 Go to Control Panel gt Display gt Settings and adjust the resolution Windows Vista Go to Control Panel gt Appearance and Personalization Personalize Display Settings and adjust the resolution Windows 7 Go to Control Panel Appearance and Personalization Display Adjust Resolution and adjust the resolution How do set power saving mode Windows XP Set power saving mode in Control Panel gt Appearance and Themes Display Screen Saver Settings or BIOS SETUP on the PC Windows ME 2000 Set power saving mode in Control Panel Display Screen Saver Settings or BIOS SETUP on the PC Windows Vista Set power saving mode in Control Panel Appearance and Personalization Personalize Screen Saver Settings or BIOS SETUP on the PC Windows 7 Set power saving mode in Control Panel Appearance and Personalization Personalize Screen Saver Settings or BIOS SETUP on the PC A Refer to the user manual for your PC or graphics card for further instructions on adjustment 8 Troubleshooting Guide Specifications General Model Name S22A650S S24A650S Panel Size 21 5 inches 54 cm 24 inches 61 cm Display area 476 64 mm H x 268 11 mm V 531 36 mm H x 298 89 mm V Synchronization Horizontal 30 81 kHz Frequency Vertical 56 75 Hz Frequency Display Color 16 7M Resolution Optimum 1920 x 108
58. uct The following screen will appear SETUP amp RESET e Off Deactivate the off timer so that the product does not power off automatically e On Activate the off timer so that the product powers off automatically 4 Press a v to move to the option you want and press the 0 6 5 The selected option will be applied 6 Setup and Reset Setup and Reset 6 10 Off Timer Setting The off timer can be set within a range of 1 to 23 hours The product will automatically power off after the specified number of hours A This menu is only available when Off Timer On Off is set to On 6 10 1 Configuring Off Timer Setting Press MENU on the product 2 Press a v to move to SETUP amp RESET and press on the product 3 Press afv to move to Off Timer Setting and press on the product The following screen will appear SETUP amp RESET 4 Press a v to configure Off Timer Setting 6 Setup and Reset Setup and Reset 6 11 Reset Return all the settings for the product to the default factory settings 6 11 1 Initializing Settings Reset Press MENU on the product 2 Press a v to move to SETUP amp RESET and press on the product 3 Press a v to move to Reset and press O amp on the product The following screen will appear SETUP amp RESET 4 Press a v to move to the option you want and press the 3 5 The selected option will be applied 6 Setup and Reset 7 1 7
59. ure quality To avoid this it is recommended that you select the optimum resolution specified for the screen size of your product e _ Check the frequency when you exchange a CDT monitor connected to a PC for an LCD monitor If the LCD monitor does not support 85Hz change the vertical frequency to 60Hz using the CDT monitor before you exchange it with the LCD monitor If a signal that belongs to the following standard signal modes is transmitted from your PC the screen will automatically be adjusted If the signal transmitted from the PC does not belong to the standard signal modes the screen may be blank with the power LED on In such a case change the settings according to the following table by referring to the graphics card user manual Mein Paral Men mercio syne Pty kHz Hz Mid hae IBM 640 x 350 31 469 70 086 25 175 IBM 720 x 400 31 469 70 087 28 322 Er MAG 640 x 480 35 000 66 667 30 240 MAC 832 x 624 49 726 74 551 57 284 J MAC 1152 x 870 68 681 75 062 100 000 J VESA 640 x 480 31 469 59 940 25 175 of VESA 640 x 480 37 861 72 809 31 500 VESA 640 x 480 37 500 75 000 31 500 VESA 800 x 600 35 156 56 250 36 000 VESA 800 x 600 37 879 60 317 40 000 VESA 800 x 600 48 077 72 188 50 000 VESA 800 x 600 46 875 75 000 49 500 4 4 VESA 1024 x 768 48 363 60 004 65 000 J VESA 1024 x 768 56 476 70 069 75 000 VESA 1024 x 768
60. ve the menu position to the left or right Menu V Position Move the menu position up or down 5 3 1 Configuring Menu H Position amp Menu V Position 7 Press MENU on the product 2 Press a v to move to SIZE amp POSITION and press 53 on the product 3 Press a v to move to Menu H Position or Menu V Position and press 0 0 The following screen will appear SIZE amp POSITION 4 Press a v to configure Menu H Position or Menu V Position 5 Resizing or Relocating the Screen 55 6 1 Setup and Reset ECO The Eco Motion Sensor Eco Light Sensor and Eco Saving options are displayed on the same menu page so that you can conveniently configure the power saving settings 6 1 1 Eco Motion Sensor The Eco Motion Sensor activates to save power when it does not detect any movement within a specified area for a specified period of time Eco Motion Sensor is not available when the monitor is used in portrait mode Configuring Eco Motion Sensor KR b Press MENU on the product Press a v to move to SETUP amp RESET and press on the product Press a v to move to ECO and press on the product Press a v to move to Eco Motion Sensor and press The following screen will appear NG This option is disabled if the product is connected to a PC that is in power saving mode Off Deactivate the Eco Motion Sensor function 5 Min Automatically turn off the power if the sensor ha
61. w samsung com MONGOLIA 7 800 555 55 55 http www samsung com RUSSIA 8 800 555 55 55 http www samsung com TADJIKISTAN 8 10 800 500 55 500 http www samsung com UKRAINE 0 800 502 000 http www samsung com ua Ukrainian http www samsung com ua_ru Russian UZBEKISTAN 8 10 800 500 55 500 http www samsung com ASIA PACIFIC AUSTRALIA 1300 362 603 http www samsung com CHINA 400 810 5858 http www samsung com HONG KONG 852 3698 4698 http www samsung com hk Chinese http www samsung com hk_en English Appendix Appendix ASIA PACIFIC INDIA 1800 1100 11 http www samsung com 3030 8282 1800 3000 8282 1800 266 8282 INDONESIA 0800 112 8888 http www samsung com 021 5699 7777 JAPAN 0120 327 527 http www samsung com MALAYSIA 1800 88 9999 http www samsung com NEW ZEALAND 0800 SAMSUNG 0800 726 786 http www samsung com PHILIPPINES 1 800 10 SAMSUNG 726 7864 http www samsung com for PLDT 1 800 3 SAMSUNG 726 7864 for Digitel 1 800 8 SAMSUNG 726 7864 for Globe 02 5805777 SINGAPORE 1800 SAMSUNG 726 7864 http www samsung com TAIWAN 0800 329 999 http www samsung com 0266 026 066 THAILAND 1800 29 3232 http www samsung com 02 689 3232 VIETNAM 1 800 588 889 http www samsung com MIDDIE EAST BAHRAIN 8000 4726 http www samsung com ae English http www samsung com ae_ar Arabic EGYPT 08000 726786 http www samsung com I
62. xterior may differ depending on the product APAPAP De re re E ise te te 110 cm Precautions for storage High glossy models can develop white stains on the surface if an ultrasonic wave humidifier is used nearby A Be sure to contact Samsung Customer Service Center page 84 if the inside of the monitor needs cleaning service fee will be charged Before Using the Product Safety Precautions Electricity and Safety NG The following images are for reference only Real life situations may differ from what is shown in the images A Warning Do not use a damaged power cord or plug or a loose power socket e An electric shock or fire may result Do not plug many products into the same power socket e Otherwise the socket may overheat and cause a fire Do not touch the power plug with wet hands e Otherwise an electric shock may result Insert the power plug all the way in so it is not loose e An unstable connection may cause a fire Connect the power plug to a grounded power socket type 1 insulated devices only e An electric shock or injury may result Do not bend or pull the power cord with force Do not weigh the power cord 7 o down with a heavy object e Adam wer cord m an electric shock or fire damaged power cord may cause Do not place the power cord or product near heat sources e An electric shock o
63. you want and press the 5 0 The selected option will be applied 6 Setup and Reset 60 Setup and Reset 6 1 3 Eco Saving The Eco Saving function reduces power consumption by controlling the electric current used by the monitor panel K e This menu is not available when Eco Light Sensor is set e This menu is not available when MAGiGBright is in Dynamic Contrast mode Configuring Eco Saving Press MENU on the product Press a v to move to SETUPS RESET and press 3 on the product Press a v to move to ECO and press on the product A N ra Press a v to move to Eco Saving and press 3 on the product The following screen will appear e 75 Change the monitor power consumption to 75 of the default level e 50 Change the monitor power consumption to 50 of the default level e Off Deactivate the Eco Saving function 5 Press a v to move to the option you want and press the 0 6 6 The selected option will be applied 6 Setup and Reset 61 Setup and Reset 6 1 4 Eco Icon Display Configuring Eco Icon Display 7 Press MENU on the product 2 Press a v to move to SETUP amp RESET and press 3 on the product 3 Press a v to move to ECO and press 3 on the product 4 Press a v to move to Eco Icon Display and press 53 The following screen will appear e Off Disable the Eco Icon Display function e On Display the operation status of the Eco sensor as a pop up gu

Download Pdf Manuals

Related Search

Related Contents

Edbak SAP3S-B flat panel wall mount  Samsung AS09FA User Manual  Rugged Tablet Computer User`s Manual Trimble Site Tablet  PHYSIODISC Prótesis de disco cervical ESTÉRIL MANUAL  WATERLOG H-3301/3311  manual de instruções do soprador térmico modelo  invertidor multi-tipo manual de instalación para uso del personal  Stereo Headphones How to use/Utilisation/Utilización  DESACCOUTUMANCE AU TABAC TABAKENTWOHNUNG  rapport d=enquête sur événement aéronautique perte de puissance  

Copyright © All rights reserved. Failed to retrieve file