Toyota JFS18 sewing machine
Contents
1. 46 30 23 46 40 Trouble Cause Countermeasure Page The needle is not correctly installed Install the needle correctly 23 The needle is bent Replace with a straight needle 23 Missed stitches The needle and thread are not appro Sew with a needle and thread 24 priate for the fabric appropriate to the fabric The upper thread is not correctly EE Thread the upper thread correctly 16 ea of the upper thread is too Adjust the thread tension 30 The upper and lower thread are not Thread the upper and lower thread 15 The fabric correctly threaded again 16 wrinkles The needle is too thick for the fabric Ge EE 24 fabric The needle is damaged Replace with a good needle 23 ENEE Thread the lower thread correctly 15 threaded Too much lower thread appears The tension of the upper thread is too Adjust the thread tension 30 on the right side tight GE The bobbin is not correctly inserted in Correctly insert the bobbin in the 15 the bobbin case bobbin case The upper thread is not correctly threaded not inserted in the tension Thread the upper thread correctly 16 Too much upper disc thread appears The tension of the upper thread is too Adjust the thread tension 30 on the wrong loose Sigel Meanie The upper thread is not correctly threaded not threaded through the Thread the upper thread correctly 16 thread guide Turn the handwheel towards The needle position is too low yourself to raise the needle to the 42 highest position Needle No2. hold the ends of the lower thread 1 ffe as shown in the diagram and pull up the fabric gt in the direction of the arrow to make the gathering After making the gathering sew the smocking between 2 rows of gathering After sewing the smocking pull out the thread you used to make the gathering 39 9 Embroidery CAUTION CH Before setting the darning adapter remove the power plug from the outlet Not doing so could cause an injury A free machine embroidery pattern can be created Trace your design on the material and centre it in an embroidery hoop Lay stabilizer underneath thin fabric Install a darning adapter and then sew For model 7140 DE21 use the drop feed that comes with the sewing machine instead of a darning adapter refer to P 45 Using the drop feed Darning adapter Insertion holes Align the accessory darning adapter with the insertion holes Insert until there is a locking sound to install to the needle plate Needle plate 40 Presser foot holder Loosen the presser foot holder screw with the needle plate screw driver to release the holder Firmly stretch the fabric with the design and set in the embroidery hoop Note Purchase a commercially available embroi dery hoop At the start of sewing prepare by sewing one stitch pulling the upper thread and pulling out the lower thread above the fabric Hold the upper and lower threads then make 2 3 stitche
3. 9 is being used Use needle No 11 through 16 43 Needle threader does not work The needle is not correctly installed Install the needle correctly 23 The needle is bent Replace with a straight needle 23 The thread is not correctly set in the Pass the thread through the needle 17 needle guide guide correctly If the above treatments do not solve the problem contact the service center as described in your warranty 5 Servicing double insulated products 230 V 240 V In a double insulated product two systems of insulation are provided instead of grounding No ground ing means are provided on a double insulated product nor should a means for grounding be added to the product Servicing a double insulated product requires extreme care and should only be done by qualified service personnel with knowledge of the system under his or her responsibility Replacement parts for a double insulated product must be identical to those parts in the product The symbol is marked on the double insulated product 51 VI Others 1 Specifications Needle Home use sewing machine needle HA 1 Width 419 mm Sewing machine size Depth 166 mm Height 293 mm Rated power consumption 70 W Light bulb 15 W If you have any queries about this TOYOTA sewing machine check the warranty for details 2 Recycling DO NOT THROW AWAY EU ONLY We are committed to the protection of the environment We strive to minimize the environmental impact of our p
4. cover Extension table Accessory Box Accessories are kept here If the table is removed it becomes a free arm sewing machine Needle clamp screw Presser foot holder Presser foot Feed dog Needle plate Upper thread tension dial Refer to P 30 Adjusting thread tension Spool pin Refer to P 13 Winding the lower thread Refer to P 26 x Reverse sewing gt 6 Handle Thread winding spindle Model label Bobbin stopper Buttonhole adjustment screw Handwheel Presser foot lever Declutch knob Power switch Not equiped with RS2000A B series Terminal box l The foot controller may differ from model to model PS es y K f f Power switch Not equiped E with RS2000A B series Terminal box Connector Power plug Declutch knob Refer to P 14 Winding the lower thread 4 Buttonhole adjustment screw Refer to P 36 Adjustment of buttonhole balance x Presser foot lever Refer to P 16 Threading the upper thread Some parts may not apply to your sewing machine The MODEL and SERIES numbers are located on the model label on the back of the sewing machine Side pattern selection dial type kk Upper thread tension dial Thread guide heh bas a e Spool pin soles eal FR o N o Face cover l Pattern selection dial Thread cutter SNK Shuttle cover Reverse sewing lever Remove extension table Accessory Box e to locate
5. tension of the bobbin case suspend bobbin bobbin case and shuttle hook all together and hold the bobbin thread as illustrated Please refer to P 46 Note When the bobbin case tension is correct the thread should slide down with light resistance When the bobbin case tension Is too tight the thread does not slide down or the thread jerks When the bobbin case tension is too loose the thread easily slides down with no resistance SEWING 4 Overcasting This is a sewing method that prevents unraveling at the edge of the fabric Zigzag sewing foot Originally attached to the sewing machine Right needle entry point Position the fabric so that the right needle entry point at the edge of the fabric is slightly on the outside It is easier to sew accurately if an overcasting foot is used Optional Accessory 31 Sewing 5 Blind hem stitching In this sewing method the stitch cannot be seen on the right side of the fabric Zigzag sewing foot Originally attached to the sewing machine Fold back the fabric so that the folded area protrudes by about 5 to 7mm lron and tack by hand Inside fold Position the fabric so that the needle slightly catches the fold when the needle moves to the left Lower the presser foot and start sewing The part of the stitch that catches the fold will be visible from the right side of the fabric Sew the stitch evenly so that the
6. 0 to No 60 Polyester No 30 to No 50 Cotton No 80 to No 120 Cotton No 60 to No 80 Cotton No 40 to No 50 Silk No 80 Silk No 50 to No 80 Silk No 50 Normal back fabric Normal front fabric Curtains Quipler Broad Denim Georgette Soft denim Quilting Lawn Satin Fleece Relationship between the needle thread and fabric Fabric Lace etc Pile Tweed Gingham etc Felt etc Thread tension 3 to 5 Adjusting the thread Use a ball point needle for the sewing alignment of stretch fabric Please purchase any needles not included as accessories after checking they are specifi ed as home use sewing machine needles Refer to P 30 Adjusting thread tension for how to adjust thread tension Use the same kind of threads for upper lower thread The higher the needle number is the needle gets thicker The higher the thread number is the thread gets thinner 24 lll Sewing 1 Straight stitching and reverse sewing Reverse sewing is performed at the beginning and end of sewing to prevent the thread from unraveling Z N CAUTION Do not pull the fabric excessively while sewing Doing so could break the needle and cause an injury Zigzag sewing foot Originally attached to the sewing machine 1 Turn the handwheel towards yourself to raise the needle 2 Turn the pattern selection dial to choose the pattern Set the fabric and lower the presser foot lever Step on the foot controller to b
7. BELGIUM TEL 32 0 2 387 0707 FAX 32 0 2 387 1995 UK Branch Unit 4 Swan Business Park Sandpit Road Dartford Kent DA1 BEID UK TEL 44 0 1322 291137 FAX 44 0 1922 279214 France Branch Bat Le Minnesota allee Rosa Luxembourg BER 70294 95615 Cergy Pontoise Cedex FRANCE TEL 33 0 134 30 25 00 FAX 33 0 1 34 30 25 01 Germany Branch Odenwaldstrasse 3 D 63263 Neu lsenburg GERMANY TEL 49 0 61 02 3 67 89 0 FAX 49 0 61 02 3 67 89 13 Holland Branch Energieweg 14 2382 NJ Zoeterwoude Rijndijk THE NETHERLANDS TEL 31 0 71 5410251 FAM 31 0 71 5413707 Austria Branch Donaufelderstrasse 101 5 1 A 1210 Wien AUSTRIA TEL 43 0 1 812 06 33 FAX 43 0 1 812 06 33 11 679111 CCA10 RS2000 SDU
8. Ca TOYOTA RS Series HOME USE SEWING MACHINE INSTRUCTION MANUAL s Read this manual carefully before use and always follow the instructions Keep the manual in a convenient place for easy reference s If you give the sewing machine to someone else also give them this instruction manual Type designation RS series has several types The types are shown on the model label as follows MODEL MODELE MODEL NAME SERIES SERIE RS SERIES SERIE RS2000 SERIES SERIE RS2000A SERIES SERIE RS2000B SERIES SERIE Model label When calling for service please note the MODEL and SERIES numbers that are inscribed on the back of your sewing machine MODEL number SERIES number MODEL MODELE RS SERIES SERIE Manufacturer ZHEJIANG AISIN ELITE C 4 RS Fabricant MACHINERY A ELECTRIC CO LTD P R C i Importer AISIN EUROPE 5 A 230 240V L 50Hz importateur 70W 9 max 15w MADE IN P R C FABRIQUE EN R P C CONTENTS Weg 1 Important safety Ta Ed e de EE 3 2 How to change the power plug nnnannannnnnnnnnnnnnnnnnnonnrnnnnnrnnrnrnnnnnrnnrnnnnennen 5 AFCA ee aaa aeee ox aaa nae ease naan cae Goan aT Sa OEE 6 Il SEWING preparations ccscccecsecccerseeseeccsesseccuenerecerserecersuesenenanseeseass 10 ls Connecting ING DOW Cl esiccsetcescktcecemiircn attra ceandae deni tanteteeatcanueenedes denen 10 2 TAKING OUl TAG DOD DIN aas a 12 37 VVINGIAG ING TOWS UNKCAG EE 13 4 Thre
9. UTION CH Before threading the upper thread remove the power plug from the outlet Not doing so could cause an injury Presser foot lever A Raise the presser foot lever Note If the presser foot lever is not raised the thread cannot be set correctly Spool pin Pull out the spool pin from the main unit 1 Turn the spool pin over and insert 2 Insert the thread spool 16 Support the thread on the sewing machine with one hand using the other hand pass the thread around the thread guide as shown in the diagram Pass the thread between the thread guide plate and the tension disc Take up lever Pass the thread along the groove of the thread guide plate Turn the handwheel towards yourself until the take up lever is visible Pass the thread through the take up lever Set the thread on the left side of the needle guide Check that the thread is set correctly Raise the presser foot and pull the upper thread towards yourself The thread should come out uide lett canine Lower the presser foot and pull the upper thread towards yourself It should be resistant and diffi cult to pull g Pass the thread through the needle eye from the front 17 6 Pulling up the lower thread Hold the end of the thread turn the handwheel towards yourself for one full turn and stop when the needle is at its highest position s SS Handwheel 6 d I Never turn in the wrong direct
10. ading the lower Ureag E 15 5 Threading the Upper read 16 6 Pulling up the lower thread E 18 ls EE der Dale FIV TEE 19 8 Application of each stitch poattem 20 9 Changing Ane Presser TOOL ege geed 21 10 Changing the needle 0annannannannnnnoannnnnnnnonnnnnrnnnnnernrenresnrrnrrnrrnrennrrnrennenne gt 23 11 Relationship between the needle thread and fabric and adjusting the sewing Machine EE 24 Je Le EE 25 1 Straight stitching and reverse Sewing 25 EE EECH EE 29 3 AGJUSUNG thread ENSION BEE 30 Be CN Cea SUNG EC 31 9r BING MGM Ee EE 32 C BURONNOIG tie EE 34 MOD Slr e EE 3 Om SIMOCKINIG DEE 39 9 EMD FOIGGNY EE 40 IV Special SDCCIICANONS EEN 42 1 Using the needle reader uk 42 2 Using the presser foot pressure adiuster 44 OS ISING MC CROD 16 COs eect ta erste witcetcee aa niles aaaaey es aidiedea cee atie dunno yetiaet 45 Va Eet ET Le 46 1 Feed dog and hook maintenance E 46 Fete leet EE te EE 48 32 HONLDUID Ree E 49 4 Re le EE lee le e EE 50 5 Servicing double insulated products CG 20V 2A0N 51 Vl En EEEE OA AAEE AE 52 Is DIES CHI Gall ele EE 52 E OG VCC DEE 52 I Before use Be sure to read this section before use 1 Important safety instructions These safety instructions are designed to prevent danger or damage arising from the incorrect operation of the machine Read carefully and always follow the instructions Explanation of A WARNING and J N CAUTION Ab WARNING An incorrect operation
11. could result in death or serious injury CAUTION SOON An incorrect operation could result in an injury or damage to the machine Symbol explanation 220 to 230 V Use an AC 220 to 230 V power source Not doing so could cause an electric shock or a fire Do not damage the power cord modify it bend it excessively jerk it or twist it Doing so could cause an electric shock or a fire If the power cord is damaged it must be replaced by the manufacturer or its service agent Do not operate where aerosol spray products are being used or where oxygen is being administered Doing so could cause a fire Do not use outdoors Doing so could cause an electric shock or a fire Z N CAUTION When the machine is not in use it should be stored safely not on the floor as protruding parts could cause injury if a person fell on the machine Not doing so could cause an injury Use with the shuttle cover closed Not doing so could cause an injury Before replacing the needle or presser foot or when threading the upper or lower thread remove the power plug from the outlet Not doing so could cause an injury Do not look away from the needle while operating the sewing machine If the needle breaks it could cause an injury Do not touch moving parts such as the needle take up lever or handwheel Doing so could cause an injury Children should only use the machine under the supervision of a parent or gua
12. do not repair disassemble or modify S except at the authorised dealeror service centre Doing so could cause an electric shock or a fire disposed of safety and not stored anywhere where it could be inadvertently used again If for any reason the power plug for this product is removed it should be immediately Q Doing so could cause an electric shock or a fire The wires in this mains lead are coloured in accordance with the following code BLUE NEUTRAL BROWN LIVE OR ACTIVE As the colours of the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug PROCEED AS FOLLOWS The earth plug pin in unnecessary As the machine is designed under double insulation structure the earth wire is removed from the machine The wire coloured BROWN must be connected to the terminal marked L or A or coloured RED The wire coloured BLUE must be connected to the terminal marked N or coloured BLACK Neither core is to be connected to the earth terminal of a three pin plug 3 Part names Some parts may not apply to your sewing machine The MODEL and SERIES numbers are located on the model label on the back of the sewing machine Front pattern selection dial type Upper thread tension dial Spool pin Thread guide Pattern selection dial Face cover Thread cutter Shuttle cover Remove extension Reverse sewing lever LI table Accessory Box to locate shuttle
13. e needle clamp screw is loose The needle is too fine for the fabric The tension of the upper thread is too tight The fabric is being pulled too strongly The wrong presser foot is being used The bobbin case is not in the correct position The upper and lower thread are not correctly threaded The thread is tangled in the bobbin case or hook The tension of the upper thread is too tight The needle is bent The point of the needle is damaged There is thread waste in the feed dog A darning adapter has been installed The pattern selection dial is set to SEI or 3 50 Countermeasure Connect the power plug correctly Turn the power switch on Move the declutch knob back to the original position needle position Clean the hook Oil the shuttle race Remove thread waste or dust Install the needle correctly Firmly tighten the screw Use a needle appropriate to the fabric Adjust the thread tension Do not pull the fabric strongly Use a correct presser foot Put the bobbin case in the correct position Thread the upper and lower thread again Remove thread waste from the feed dog and hook Adjust the thread tension Replace with a good needle The lower thread is not correctly Thread the lower thread correctly threaded Remove thread waste from the feed dog and hook Remove the darning adapter Set a correct pattern Page 10 10 14 46 46 46 23 ER 24 30 25 15 15 16
14. egin sewing After finishing sewing turn handwheel towards yourself until the needle is in the highest position Raise the presser foot and pull out the fabric to the rear 25 zk Thread cutter on the needle bar gt The thread cutter may differ from model to model Line up two threads and cut with the thread cutter on the needle bar Thread cutter on the face cover The thread cutter may differ from model to model Line up two threads and cut with the thread cutter on the face cover Reverse sewing is performed at the beginning and end of sewing to prevent the thread from unraveling Reverse sewing is performed while lowering the reverse sewing lever Stitch 1 to 2 cm from the edge of the fabric to prevent unravel ing at the start of sewing Sew 3 to 4 reverse stitches at the end of sewing Note Remove your finger from the reverse sewing lever to return to forward direc tion sewing 26 x Sewing thick fabric xx Fabric or 7 Sewing fabric thick paper 1 x Sewing thin fabric f f When sewing thick fabric from the edge the presser foot may tilt and be unable to feed through the fabric Place fabric or thick paper of the same thickness as the fabric you wish to sew under the presser foot This will enable smooth sewing Sewing is easier if thin paper is laid out under the fabric 27 Sewing x Sewing tube shaped fabrics xx Pull out the extensio
15. g machine and cut the thread that protrudes from the bobbin hole Then continue wind ing the thread After the winding has finished move the thread winding spindle back to the left in the direction of the arrow 1 Remove the bobbin and cut the thread 2 Move the declutch latch in the _ direction in the direction of the arrow Note If the declutch is not returned to its original position the sewing machine cannot move and will not sew 14 4 Threading the lower thread CAUTION Before setting the bobbin case remove the power plug from the outlet Not doing so could cause an injury Use a TOYOTA exclusive bobbin Bobbin case Take out the bobbin case refer to P 12 Taking out the bobbin The thread must flow off the bobbin in the direction of the arrow and then insert the bobbin into the bobbin case Hold the end of the thread in your right hand and pass it through the groove in the bobbin case Pass the thread from 1 to 2 Press the bobbin with the finger of your left hand and then pass the thread through the tension spring as shown in the diagram Pull until there is a locking sound Turn the handwheel to move the needle to the highest position Always turn the handwheel towards yourself Holding the latch of the bobbin case insert the bobbin case into the shuttle race The bobbin case finger must slot into the groove 15 5 Threading the upper thread CA
16. he arrow wrong direction Open the shuttle cover Open out in the direction of the arrow Shuttle cover SX Pull up the latch of the bobbin case and use it to pull out the case Bobbin case Take out the bobbin from the bobbin case Bobbin 12 3 Winding the lower thread CAUTION gt Before taking out or setting the bobbin case remove the power plug from the outlet Not doing so could cause an injury Do not touch the lower thread winding spindle when winding the lower thread Not doing so could cause an injury Use a TOYOTA exclusive bobbin Spool pin Remove the sticker Pull up the spool pin from the sewing machine v E insert 3 2 Insert the thread spool e mm 2 e Pid E J V l em Las i Thread spool A i e m L a 1 Turn the pin around and Li Support the thread on the sewing machine with one hand using the other hand pass the thread around the thread guide as shown in the diagram 13 Declutch latch 1 Move the declutch latch in the amp direction in the direction of the arrow This ensures that the needle does not move 2 Pass the thread from the inside through the bobbin hole 3 Set the bobbin on the thread winding spindle and move the spindle to the right in the direction of the arrow zech Holding the end of the thread step on the foot controller to wind the thread 2 After winding it a little stop the sewin
17. he upper thread to the rear Note 1 If the needle is not set correctly it is not possible to pass the thread through the needle with the needle threader Refer to P 23 Changing the needle Note 2 Needle No 65 9 cannot be used with this needle threader 43 2 Using the presser foot pressure adjuster The presser foot pressure adjuster may differ from model to model x Push down type x lt Push down type gt Sewing normal fabric and thick fabric For normal straight or zigzag sewing press down A Sewing thin fabric Push down outer ring B to pop out pin A Push down pin A about half way lt Rotary type gt m Sewing normal fabric and thick fabric Dial Align 3 with the upper surface of the face cover Sewing thin fabric Dial Align 2 with the upper surface of the face cover surface of the face cover 44 3 Using the drop feed Z N CAUTION CH Before using the drop feed lever remove the power plug from the outlet Not doing so could cause an injury The feed dog can be lowered when feeding the fabric freely by hand for example when embroidering or quilting Model 7140 DE21 only Make sure the needle and the presser foot are both in the raised position To lower the feed dog push the lever back and to the left to disengage the feed dog To raise the feed dog push the lever to the right to return it to it is normal position turn the handwhee
18. iiti VV 36 7 Zipper sewing CAUTION Before changing the presser foot remove the power plug from the outlet Not doing so could cause an injury Change to the zipper foot refer to P 21 Changing the presser foot x Sewing the left side of the zipper Right side pin Left side pin 1 Set the zipper foot to the right side pin 2 Align the zipper and the fabric and tack Position the fabric so that the zipper is on the right side of the presser foot 3 Sew until just before the presser foot makes contact with the slider and then stop the sewing machine Turn the handwheel towards yourself to lower the needle into the fabric Raise the presser foot lever Move the slider to the rear of the presser foot and sew the remainder Never turn in the wrong direction Release the presser foot and set to the left side pin Sew the right side of the zipper using the same procedures as for the left side Note Sewing in the same direction as the left side will help prevent sewing misaligment 38 8 Smocking Zigzag sewing foot Originally attached to the sewing machine A Is not available for 16 18 stitch model refer to P 20 Application of each stitch pattern Lower noan Ok To make the gathering LAAK Viti hil oe Set the pattern selection dial to 8 4 d Sr EIS LADA lt Loosen the tension of the upper thread and sew Qe After sewing
19. ion Note Always turn the handwheel towards your self in the direction of the arrow If you turn it in the reverse direction it could tangle the thread Note If the thread is tight the lower thread will not come out so hold the thread loosely Pull the upper thread and the loop of the lower thread will come out Pull out this lower thread Line up the upper thread and lower thread and thread through the groove of the presser foot Pull back about 15cm 18 Sewing preparations 7 Main stitch pattern uses Depending on the model of your sewing machine some of the stitch patterns are not available refer to P 20 Smocking Straight ee Stitch secure sewing Fagotting VV Decorative stitching E Applique TE Zipper sewing Overcasting HE Blind hem stitching l l Buttonhole sewing 19 8 Application of each stitch pattern Z N CAUTION Do not turn the pattern selection dial while operating the sewing machine Doing so could cause an injury Pattern selection diat i Attention he number of stitch patterns may differ from model to model npe Q A The model number is located on the model label on the back of the sewing machine MODEL es H Ca 21 Stitch programs MODEL XXX21 XXX17 XXX04 7140 SA45 a jg 18 Stitch programs MODEL XXX18 CB02 STF91 Kr S s g 16 Stitch programs MODEL XXX16 CB01 7120 Turn the ha
20. l one full turn to engage the feed mechanism Drop feed lever 45 V Maintenance 1 Feed dog and hook maintenance If the sewing machine makes a loud noise or rotates slowly the oil could have run out or there could be thread waste or dust in the hook or feed dog Clean and oil the hook and feed dog Before cleaning the hook remove the power plug from the outlet Not doing so could cause an injury Do not use detergent bleach benzine or thinner chemical cloths Doing so could cause discoloration or cracking 4 Release the presser foot and use the needle plate screw driver to release the needle plate Needle plate Remove thread waste and dust with a brush Optional accessory Remove the bobbin case da NA Bobbin case 46 Open the left and right stoppers to the outside in the direction of the arrow Take out the shuttle hook cover Take out the shuttle hook Wipe the shuttle race clean with a brush or soft cloth Apply one drop of oil to the shuttle race Note 1 If too much oil is applied it could cause trouble such as dirty thread or bobbins or sewing malfunctions Keep to this small amount Note 2 Use the oil supplied with your machine or special oil for sewing machines Other oils could cause mechanical prob lems 47 2 Hook installation The hook is installed by reversing the removal procedures Replace the shuttle hook Align the projection of
21. n table accessory box in the direction of the arrow Sew tube shaped fabrics such as trousers or sleeves 28 Sewing 2 Zigzag sewing There are various types of zigzag sewing methods such as applique and overcastting Zigzag sewing foot Originally attached to the sewing machine ER 3 5 5 0mm CC Turn the handwheel towards yourself to raise the needle Turn the pattern selection dial to choose the pattern Set the fabric and lower the presser foot Step on the foot controller to begin sewing 3 Adjusting thread tension Before adjustment check again that P 16 Threading the upper thread has been performed correctly x Adjustment method for upper thread tension Ze Straight stitch OUpper thread is tight tension dial thread Zigzag sewing Upper thread is tight Right side Wrong side Upper thread is loose Right side Wrong side 30 AC VEN Turn down the upper thread OUpper thread is loose Turn up the upper thread tension dial Note If the tension does not change even when you turn the upper thread tension dial reset the upper thread Note If it does not change with the upper thread adjust the lower x Adjustment method for lower thread tension x QOAdjust by turning the bobbin case adjustment screw with the accessory screw driver Turn right to tighten the tension Turn left to loosen the tension QAfter adjusting the
22. ndwheel towards yourself to raise the needle to the highest position Turn the pattern selection dial to choose the pattern Stitch Stitch Stitch Applications programs Applications programs 1 2 3 4 Stretch fabric blind hem stitch Thin fabric straight Decorative stitch stitch Overcasting Straight stitch Straight stretch stitch Zipper sewing secure sewing Zigzag sewing Applique Overcasting Overcasting Overlock Mending stitch Thin fabric overcastting Fagoting Casing Decorative stitch Decorative stitch Double overlock 9 Changing the presser foot Z N CAUTION CH Before changing the presser foot remove the power plug from the outlet Not doing so could cause an injury zk Removal Never turn in the wrong direction Presser foot lever IK Handwheel 1 Raise the presser foot lever 2 Turn the handwheel towards yourself to raise the needle Press the presser foot holder lever in the direction e of the arrow to release the presser foot Presser foot 7 holder lever 21 zk Installation Presser foot holder Position the presser foot pin directly below the groove in the presser foot holder Presser foot pin Lower the presser foot lever to set the presser foot 22 10 Changing the needle b CAUTION Before changing the needle remove the power plug from the outlet Not doing so could cause an injury children Not doing so could ca
23. ng on the fabric Guide line Raise the needle to the highest position set the pattern dial to 1 and sew 5 to 6 bar tack stitches Raise the needle to the highest position set the pattern dial to 2 sew the left side and stop at the line marked on the fabric Raise the needle to the highest position set the pattern dial to 3 and sew 5 to 6 bar tack stitches 1 and 3 on the pattern selection dial use the same dial position Raise the needle to the highest position set the pattern dial to 4 sew the right side and stop at the line marked on the fabric 35 A CAUTION front of the cutter When using the buttonhole cutter to cut the buttonholes do not hold the fabric in Doing so could cause an injury to your hand Use the buttonhole cutter to cut the center making sure not to cut the stitches Note If a marking pin is put in the bar tack area it helps to prevent excessive cutting with the buttonhole cutter Use the buttonhole adjustment screw to adjust the balance between the stitches rear side Adjust by turning with the needle plate screw driver JJ Buttonhole rl adjustment screw TTP PTT DUR bibd ddd bdbbdbdbadda If the stitches are loose on the right side of the buttonhole turn slightly in the direction VVVVVVVVVV If the stitches are loose on the left side of the buttonhole turn slightly in the direction PUTTER TT PETE TTT iiiid iidiiiiiiili
24. part of the stitch that catches the fold is not too large or too small After sewing pull out the tacking open out the fabric Right side 32 Sewing Needle catches too much Needle does not catch on the fold on the fold Balanced stitches Wrong aide Rightside_ Wrong side Right side Wrong side Right side Large stitches on the The blind hem stitches do right side not come through Small stitches evenly located on the right side It is easier to sew accurately if a blind stitch foot is used Optional Accessory 33 6 Buttonhole CAUTION Before changing the presser foot remove the power plug from the outlet Not doing so could cause an injury Buttonhole sewing to match the size of the button is possible For stretch fabric or thin fabric a fusible interlining on the wrong side of the fabric will reinforce the fabric and produce a good finish for the buttonhole Buttonhole foot Center line 3mm Change to the buttonhole foot refer to P 21 Changing the presser foot Get the buttonhole size and mark a line on the fabric T Button thickness Buttonhole Note For stretch fabric or thin fabric insert a fusible interlining on the wrong side of the fabric before sewing Button diameter button thickness 3mm 34 Division line Align the buttonhole foot division line closest to Start line you with the guide line and lower the presser foot of Sewing to the start line of sewi
25. rdian Otherwise they could injure themselves Do not use when young children are near the machine They could touch the needle and be injured Before leaving the sewing machine after using it remove the power plug from the outlet Not doing so could cause an injury Before using the sewing machine make sure that the presser foot holder clamp screw needle clamp screw and needle plate screw are firmly tightened and that the presser foot is properly set in the presser foot holder Not doing so could cause an injury Sewing without lowering the presser foot Sewing while the needle is incorrectly installed Using a bent needle Sewing while jerking the fabric Moving the pattern selection dial while sewing Do not perform the following actions Doing so could cause an injury Do not operate on an unstable surface such as a sofa or a bed If the sewing machine falls down it could cause an injury or damages to the machine Do not drop or insert any foreign objects into any openings such as opening space when you remove the face cover and or the outer casing space of bobbin case Doing so could cause an injury or damages to the machine Do not repair disassemble or modify except what is mentioned in the instruction manual Doing so could cause an electric shock a fire or an injury UK ONLY IMPORTANT PLEASE READ CAREFULLY 2 How to change the power plug A WARNING When you change the power plug or cord
26. roducts by continuously improving product design and our manufacturing meth ods At end of life please dispose of this product in an environmentally responsible way The crossed out wheelie bin symbol featured above and on the product s data plate means that this product falls under the scope of the E U Waste Electrical and Electronic Equipment WEEE directive and Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment ROHS directive and should not be disposed of with your household waste At end of life you must en sure that this product is disposed of in accordance with national and local legislation and that it is sorted as Category 2 Small Domestic Appliances WEEE You may be liable under local and national laws for improper disposal of this product Please consult the web or a competent national or local body for the return and collections systems available to you and the locations of your nearest recycling points As an individual you can make a positive impact on reuse recycling and other forms of recovery of WEEE This will reduce use of landfill and minimize the environmental impact of the products you use Hazardous substances in electronic and electrical products can have a harmful impact on human health and on the environment 52 Imported by Importe par AISI NEU ROPE S A Web www home sewing com Head Office Avenue de l industrie 21 Parc Industriel 1420 Braine l Alleud
27. s Doing so could cause an electric shock Prepare the foot controller Insert the power cord connector into the terminal box Insert the power plug into the outlet Power switch Terminal box Connector Press the power switch to I On The power is turned on 10 x Machine without a power switch xx RS2000 A B series only A WARNING CH Hold the power plug when removing it from the outlet Not doing so could damage the cord and cause an electric shock fire or injury Si Do not touch the power plug with wet hands Si Doing so could cause an electric shock Prepare the foot controller Insert the power cord connector into the terminal box Insert the power plug into the outlet The power is turned on at the outlet Terminal box R F Connector Step on the foot controller to operate the sewing machine The more you press the foot controller the faster the machine runs Release the foot controller to stop the machine Foot controller 11 2 Taking out the bobbin WARNING Before taking out or setting the bobbin case remove the power plug from the outlet Not doing so could cause an injury Handwheel 1 Turn the handwheel to move the needle to the highest position Always turn the handwheel towards yourself in the direction of the arrow 2 Hold the left edge of the extension table and Never turn in the pull out to the left in the direction of t
28. s snip off excess threads Sew along the outline of the design so there is no clearance between stitches D n 41 IV Special specifications 1 Using the needle threader Z N CAUTION Before using the needle threader remove the power plug from the outlet Not doing so could cause an injury Handwheel Turn the handwheel towards yourself to raise the needle to the highest position in the direction of the arrow ee Note Always turn the handwheel towards your ever turn in the De Ge wrong direction self If you turn it in the reverse direction it could tangle the thread Lower the presser foot lever Slightly lower the needle threader lever and set threader Pn eg i the thread you are holding in your right hand from lever VI Te AN the right side of the hook guide G SA Needle guide Hook B Fully press down the needle threader lever to pass the hook through the needle eye Make sure that the hook is in the needle eye Note If the hook is bent and cannot pass through the needle eye straighten it with a screw driver 42 opecial specificatiol cd H Kaka JH Kaka Hold the thread set in the hook guide to the right side and insert in the needle threader groove While raising the needle threader lever remove your hand from the thread The thread is pulled by the hook and is passed through the eye of the needle as shown in the diagram Pull out the loop of t
29. shuttle cover Extension table Accessory Box Accessories are kept here lf the table is removed it becomes a free arm sewing machine Needle clamp screw Presser foot holder Presser foot ay Needle plate f ES Feed dog CN Upper thread tension dial Refer to P 30 Adjusting thread tension Spool pin Refer to P 13 Winding the lower thread Refer to P 26 x Reverse sewing x Reverse sewing lever Handle Thread winding Bobbin stopper spindle zen B D Buttonhole adjustment screw Model label Handwheel Presser foot lever Declutch knob gd Pattern selection dial C E w Power switch Not equiped with RS2000A B series Terminal box The foot controller may differ from model to model Power switch Not equiped with RS2000A B series Terminal box Connector Part name Detail by use Declutch knob Refer to P 14 Winding the lower thread 4 Buttonhole adjustment screw Refer to P 36 Adjustment of buttonhole balance xx Presser foot lever Refer to P 16 Threading the upper thread ll Sewing preparations 1 Connecting the power Machine with a power switch A WARNING Turn the power switch off when inserting the power plug y Not doing so could cause an injury Hold the power plug when removing it from the outlet Not doing so could damage the cord and cause an electric shock fire or injury Do not touch the power plug with wet hand
30. the shuttle hook cover with the depression of the hook and install the shuttle hook cover Close the left and right stoppers to the inside in the direction of the arrow Hold the latch of the bobbin case and insert the bobbin case into the shuttle race The bobbin case finger must slot into the groove 48 3 Light bulb replacement Light bulb is not equipped with RS2000B series WARNING Before changing the light bulb remove the power plug from the outlet and wait until the bulb cools Not doing so could cause a burn or electric shock Loosen the screw and take off the face cover Turn the light bulb counterclockwise and remove Turn the new light bulb clockwise to install Note Use a light bulb with a maximum power of 15W Always reinstall the face cover after replacing the light bulb 49 4 Troubleshooting What is the problem Check the following possibilities before taking the sewing machine in for repair Trouble Does not rotate Does not work Loud noise Slow rotation Broken needle Broken upper thread Broken lower thread Fabric not fed through Cause The power plug is not inserted The power switch is off The declutch knob is in the lower thread winding position Thread is tangled in the hook or there is a broken needle in the hook The oil has run out There is thread waste or dust in the hook or feed dog The needle is incorrectly installed Th
31. use an injury a Broken needles are dangerous Be sure to dispose of them in a safe place away from Needle plate screw driver 1 Turn the handwheel towards yourself to raise the end of the needle higher than the needle plate 2 Hold the needle in one hand loosen the needle clamp screw with the accessory needle plate screw driver and remove the needle Note Do not remove the needle clamp screw Loosen the needle clamp screw to remove the needle 1 Face the flat surface of the needle to the rear and insert until it makes contact with the pin 2 Firmly tighten the needle clamp screw with the needle plate screw driver zk Correct needle selection Note If a faulty needle is used not only will it impair the sewing performance but it could also damage the metal plate or hook or break the needle If a stitch is missed or the thread breaks first try replacing the needle X Faulty needle It s The point of the The point of the use a faulty The entire needle is bent needle is blunt needle is bent needle 23 11 Relationship between the needle thread and fabric and adjusting the sewing machine The quality of the sewing finish will improve if the needle and thread are changed to match the type of fabric Follow the directions in the table below Sewing thin fabric Sewing normal fabric Sewing thick fabric No 65 9 to No 75 11 No 75 11 to No 90 14 No 100 16 Polyester No 90 Polyester No 5
Download Pdf Manuals
Related Search