NEC EA294WMI-BK
Contents
1. English 27 Manufacturer s Recycling and Energy Information NEC DISPLAY SOLUTIONS is strongly committed to environmental protection and sees recycling as one of the company s top priorities in trying to minimize the burden placed on the environment We are engaged in developing environmentally friendly products and always strive to help define and comply with the latest independent standards from agencies such as ISO International Organisation for Standardization and TCO Swedish Trades Union Disposing of your old NEC product The aim of recycling is to gain an environmental benefit by means of re use upgrading reconditioning or reclamation of material Dedicated recycling sites ensure that environmentally harmful components are properly handled and securely disposed To ensure the best recycling of our products NEC DISPLAY SOLUTIONS offers a variety of recycling procedures and gives advice on how to handle the product in an environmentally sensitive way once it has reached the end of its life All required information concerning the disposal of the product and country specific information on recycling facilities can be found on our following websites http www nec display solutions com greencompany in Europe http www nec display com in Japan or http www necdisplay com in USA Energy Saving This monitor features an advanced energy saving capability When a VESA Display Power Management Signalling DPMS Sta2. 75 Hz 1280 x 1024 60 Hz to 75 Hz 1400 x 1050 60 Hz 1920 x 1080 60 Hz 30 Hz HDMI MHL 2500 X 1080 Co 60 HZ i oc aa aa 672 8 mm 26 5 inches 283 8 mm 11 2 inches 283 8 mm 11 2 inches 672 8 mm 26 5 inches USB Specification Revision 2 0 Upstream 1 Downstream 4 Maximum 0 5A per port Analog Audio Digital Audio Digital Audio 1 0W 1 0W Stereo Micro jack 2 5 Stereo Micro jack 2 5 AC 100 240 V 50 60 Hz 1 00 0 50 A with USB and Audio Notes Active matrix thin film transistor TFT liquid crystal display LCD 0 263 mm dot pitch 300 cd m white luminance 1000 1 contrast ratio typical 25000 1 Contrast ratio Dynamic DisplayPort Complies with Standard V1 2 applicable to HDCP DVI HDCP DVI HDCP 0 7 Vp p 75 ohm Separate sync TTL level Positive Negative Composite sync TTL level Positive Negative Sync on Green Video 0 7 Vp p and Sync Negative 0 3 Vp p HDMI MHL Depends on display card used Automatically Automatically Automatically Some systems may not support all modes listed NEC DISPLAY SOLUTIONS cites recommended Stereo L R 500mV rms 20 Kohm PCM 2ch 32 44 1 48 kHz 16 20 24bit PCM 2ch 32 44 1 48 kHz 16 20 24bit Headphone Impedance 32 Ohm 705 8 mm W x 410 4 540 4 mm H x 230 0 mm D 27 8 inches W x 16 2 21 3 inches H x 9 1 inches D 321 8 mm W x 722 0 732 4 mm H x 230 0 mm D 12 7 inches W x 28 4 28 8 inches H x 9 1 inche
3. clarity and image stability by increasing or decreasing this setting If the AUTO ADJUST function and the H SIZE function do not give you a satisfactory picture setting a fine tuning can be performed by using the FINE function For this a Moir test pattern could be used If the FINE value is wrongly calibrated the result would look like the left drawing The image should be homogeneous l When FINE value is When FINE value is wrong correct INPUT RESOLUTION Analog input only Selects one of the following pair of resolutions as the input signal priority 1360 x 768 or 1280 x 768 or 1024 x 768 vertical resolution 768 1600 x 900 or 1280 x 960 horizontal frequency 60kHz vertical frequency 60Hz 1680 x 1050 or 1400 x 1050 vertical resolution 1050 VIDEO LEVEL HDMI input only NORMAL Disables the expanded feature EXPAND Expands image contrast and increases details in the dark and bright areas OVER SCAN HDMI input only Some video formats may require different scanning modes in order to best display the image 1 Image size is larger than what can be displayed The image edge will appear cropped Approximately 95 of the image will be shown on the screen 2 Image size is larger than what can be displayed The image edge will appear cropped Approximately 75 of the image will be shown on the screen OFF Image size stays within the display area The whole
4. HUMAN SENSING The human sensor on the front side of the monitor detects the movement of a person by using the HUMAN SENSING function The HUMAN SENSING has three settings OFF No HUMAN SENSING 1 LIGHT After it is detected that there is no person after a period of time the monitor shifts to low brightness mode automatically to reduce the power consumption When a person comes near the monitor again the monitor will automatically return to normal mode START TIME adjusts the wait time to react 2 DEEP After it is detected that there is no person the monitor shifts to power saving mode automatically to reduce the power consumption When a person comes near the monitor again it resumes from the power saving mode and displays the images SENSOR SETTING HUMAN SENSING Adjusts the threshold level of HUMAN SENSING When human icon is located on the right side of the white color bar or vermilion color wave it is detected that there is no person NOTE Once the OSD has been closed Human sensor starts to work START TIME HUMAN SENSING Adjusts the wait time of entering to low brightness mode or power saving mode when Human Sensor detects no person DV MODE Dynamic Visual Mode allows you to select from the following settings STANDARD Standard setting TEXT Setting that makes letters and lines crisp best suited for basic word processing and spreadsheets MOVIE Setting that boosts dark tones best suited for movies GAMIN
5. REDUCE THE RISK OF ELECTRIC SHOCK MAKE SURE POWER CORD IS UNPLUGGED FROM WALL SOCKET TO FULLY DISENGAGE THE POWER TO THE UNIT PLEASE DISCONNECT THE POWER CORD FROM THE AC OUTLET DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL This symbol warns user that uninsulated voltage within the unit may have sufficient magnitude to cause electric shock Therefore it is dangerous to make any kind of contact with any part inside this unit This symbol alerts the user that important literature concerning the operation and maintenance of this unit has been included Therefore it should be read carefully in order to avoid any problems CAUTION Please use the power cord provided with this display in accordance with the table below If a power cord is not supplied with this equipment please contact your supplier For all other cases please use a power cord that matches the AC voltage of the power outlet and has been approved by and complies with the safety standard of your particular country European r SAE When operating the monitor with its AC 125 240V power es use a power supply cord that matches the power supply voltage of the AC power outlet being used NOTE _ This product can only be serviced in the country where it was purchased Windows is a registered trademark of Microsoft Corporation NEC is a registered trademark of NEC Corporation ErgoDesign is a registered trade
6. all cables then the screen must be raised to the highest level and tilt to avoid knocking the screen on the desk or pinching your fingers To raise the screen place a hand on each side of the monitor and lift up to the highest position Figure RL 1 To rotate screen place a hand on each side of the monitor screen and turn clockwise from landscape to portrait or counter clockwise from portrait to landscape Figure R 1 To rotate OSD menu between landscape and portrait refer to Controls section T Figure R 1 English 8 Tilt and Swivel Grasp the top and bottom sides of the monitor screen with your hands and adjust the tilt and swivel as desired Figure TS 1 Figure TS 1 NOTE Handle with care when tilting the monitor screen Flexible Arm Installation This LCD monitor is designed for use with a flexible arm To prepare the monitor for alternate mounting purposes e Follow the instructions provided by the manufacturer of the display mount e To meet the safety requirements the mounting stand must be able to support the weight of the monitor and be UL certified Remove Monitor Stand for Mounting To prepare the monitor for alternate mounting purposes 1 Disconnect all cables 2 Place a hand on each side of the monitor and lift up to the highest position 3 Place monitor face down on a non abrasive surfac
7. be installed close to a power outlet which is easily accessible e Handle with care when transporting Save packaging for transporting e Do not touch LCD panel surface while transporting mounting and setting Applying pressure on the LCD panel can cause serious damage Image Persistence Image persistence is when a residual or ghost image of a previous image remains visible on the screen Unlike CRT monitors LCD monitors image persistence is not permanent but constant images being displayed for a long period of time should be avoided To alleviate image persistence turn off the monitor for as long as the previous image was displayed For example if an image was on the monitor for one hour and a residual image remains the monitor should be turned off for one hour to erase the image NOTE As with all personal display devices NEC DISPLAY SOLUTIONS recommends using a moving screen saver at regular intervals whenever the screen is idle or turning off the monitor when not in use English 3 CORRECT PLACEMENT AND ADJUSTMENT OF THE MONITOR CAN REDUCE EYE SHOULDER AND NECK FATIGUE CHECK THE FOLLOWING WHEN YOU POSITION THE MONITOR e For optimum performance allow 20 minutes for the display to warm up e Adjust the monitor height so that the top of the screen is at or slightly below eye level Your eyes should look slightly downward when viewing the middle of the screen e Position your monitor no closer than 40 cm 15 75 inches and
8. brightness lf ECO MODE is set to 1 or 2 a bar for CARBON FOOTPRINT will appear CONTRAST Adjusts the overall image and background screen brightness by input signal level ECO MODE Decreases the amount of power consumption by reducing the brightness level OFF No function 1 ENERGY STAR SETTING Sets brightness variable range from 0 to 60 This setting can adjust brightness to a range in which power is reduced to meet Energy Star measurement conditions 2 40 POWER SAVINGS Sets brightness variable range from 0 to 30 This setting can adjust brightness to a range in which power is reduced by 40 compared to the maximum brightness setting When this function is set to ON a CARBON FOOTPRINT bar will appear alongside the brightness adjustment bar NOTE This function is disabled when DV MODE is set to DYNAMIC This function is disabled when Color Control System is set to DICOM SIM This function is disabled when PBP MODE is set to LEFT or RIGHT AUTO BRIGHTNESS OFF No function 1 AMBIENT LIGHT Automatically adjusts the brightness to the optimal setting by detecting the brightness level of the environment 1 Please refer to page 22 for full Auto Brightness information 2 WHITE CONTENT Automatically adjusts the brightness to the optimal brightness setting based on the white display area The environmental brightness sensor Ambibright sensor has no function 3 AMBIENT CONTENT Automatically adjusts the
9. brightness to the optimal setting based on the white display area and the brightness level of the environment detected by the AmbiBright sensor NOTE This function is disabled when DV MODE is set to DYNAMIC This function is disabled when Color Control System is set to DICOM SIM This function is disabled when PBP MODE is set to LEFT or RIGHT BLACK LEVEL Adjusts the black level OFF MODE SETTING The Intelligent Power Manager allows the monitor to enter into power saving mode after a period of inactivity The OFF MODE has two settings STANDARD Monitor enters into power saving mode automatically when the input signal is lost SENSOR Monitor enters into power saving mode automatically when the amount of surrounding light falls below the level determined by you The level can be adjusted via OFF MODE SENSOR SETTING The LED power indicator on the front of the monitor becomes dark blue when in power saving mode and will return to normal by touching any front keys except for POWER and INPUT When the amount of surrounding light returns to normal levels the monitor will automatically return to normal mode SENSOR SETTING OFF MODE SETTING Adjusts the threshold level of the ambient light sensor for detected dark condition and shows current sensor measurement result START TIME OFF MODE SETTING Adjusts the wait time to enter into to a lower power consumption level when the ambient light sensor detects dark condition English 12
10. image is displayed on the screen EXPANSION Sets the Zoom method see page 24 FULL The image is expanded to full screen regardless of the resolution ASPECT The image is expanded without changing the aspect ratio OFF The image is not expanded NOTE FULL works only when PBP MODE is OFF H RESOLUTION Digital input only Adjusts the horizontal size by increasing or decreasing the resolution see page 24 Press RIGHT button to reduce the width of the image on the screen Press LEFT button to expand the width of the image on the screen V RESOLUTION Digital input only Adjusts the vertical size by increasing or decreasing the resolution see page 24 Press RIGHT button to reduce the height of the image on the screen Press LEFT button to expand the height of the image on the screen English 14 Color Color Control System Color presets select the desired color setting 1 2 3 5 Increases or decreases Red Green or Blue color depending upon which is selected The change in color will appear on screen and the direction increase or decrease will be shown by the bars NATIVE Original color presented by the LCD panel that is unadjustable sRGB sRGB mode dramatically improves the color fidelity in the desktop environment by a single standard RGB color space With this color supported environment the user could easily and confidently communicate color without further color management overhead i
11. more comfortable to the eye in a variety of lighting conditions The Auto Brightness function is set to 1 by default SETUP Use the following procedures to select the Brightness Range that the monitor will use when the Auto Brightness function is activated 1 Set the BRIGHTNESS level This is the brightness level that the monitor will go up to when the ambient light level is highest Select this setting when the room is at its brightest Select 1 or 3 in the AUTO BRIGHTNESS menu Figure 1 Then use the front Keys to move the cursor up to the BRIGHTNESS setting Choose the desired brightness level Figure 2 BRIGHTNESS e CONTRAST dl oh 0 MODE AUTO BRIGHTNESS BRIGHTNESS 50 0 e CONTRAST ECO MODE ECOMODE 1 AUTO BRIGHTNESS 57 7 OFF MODE SETTING OFF 2 3 SENSOR SETTING START TIME AMBIENT LIGHT HUMAN SENSING SENSOR SETTING OFF MODE SETTING eee SENSOR SETTING CARBON FOOTPRINT START TIME HUMAN SENSING SENSOR SETTING START TIME DY MODE START TIME DY MODE Figure 1 Figure 2 2 Set the DARK level This is the level of brightness that the monitor will go down to when the ambient light level is low Make sure the room is at its darkest when setting this level Then use the front Keys to move the cursor up to the BRIGHTNESS setting Choose the desired brightness level Figure 3 BRIGHTNESS e CONTRAST oh LO MODE ECOMODE 1 AUTO BRIGHTNESS 32 2 OFF MODE SETTING e SENSOR SETTI
12. no further away than 70 cm 27 56 inches from your eyes The optimal distance is 50 cm 19 69 inches e Rest your eyes periodically by focusing on an object at least 20 feet away Blink often e Position the monitor at a 90 angle to windows and other light sources to minimize glare and reflections Adjust the monitor tilt so that ceiling lights do not reflect on your screen e lf reflected light makes it hard for you to see your screen use an anti glare filter e Clean the LCD monitor surface with a lint free non abrasive cloth Avoid using any cleaning solution or glass cleaner e Adjust the monitor s brightness and contrast controls to enhance readability e Use a document holder placed close to the screen e Position whatever you are looking at most of the time the screen or reference material directly in front of you to minimize turning your head while you are typing e Avoid displaying fixed patterns on the monitor for long periods of time to avoid image persistence after image effects e Get regular eye checkups Ergonomics To realize the maximum ergonomics benefits we recommend the following e To avoid eye fatigue adjust the brightness to a moderate setting Place a sheet of white paper next to the LCD screen for luminance reference e Do not position the Contrast control to its maximum setting e Use the preset Size and Position controls with standard signals e Use the preset Color Setting e Use non inte
13. the number of different plastics used Product Lifetime Product Take Back Minimum one year product warranty Minimum three year availability of spare parts Product take back Packaging Limits on hazardous substances in product packaging Packaging prepared for recycling Ergonomic User centered design Visual ergonomics in products with a display Adjustability for user comfort displays headsets Acoustic performance protection against sound spikes headsets and fan noise projectors computers Ergonomically designed keyboard notebooks Electrical Safety minimal electro magnetic Emissions Third Party Testing All certified product models have been tested in an independent accredited laboratory A detailed criteria set is available for download at www tcodevelopment com where you can also find a searchable database of all TCO Certified IT products TCO Development the organization behind TCO Certified has been an international driver in the field of Sustainable IT for 20 years Criteria in TCO Certified are developed in collaboration with scientists experts users and manufacturers Organizations around the world rely on TCO Certified as a tool to help them reach their sustainable IT goals We are owned by TCO a non profit organization representing office workers TCO Development is headquartered in Stockholm Sweden with regional presence in North America and Asia For more information please visit www tcodevelopment com
14. turn off by POWER SAVE TIMER function when continuing power save mode for 2 hours Please touch the power key e Check to make sure that a supported mode has been selected on the display card or system being used Please consult display card or system manual to change graphics mode e Check the monitor and your display card with respect to compatibility and recommended settings e Check the signal cable connector for bent or pushed in pins e Check the signal input DVI D DISPLAYPORT HDMI or D Sub e lf the front LED is dark blue check the status of the OFF MODE SETTING mode see page 12 or HUMAN SENSOR see page 13 e When using an HDMI input please change OVER SCAN Power Key does not respond e Unplug the power cord of the monitor from the AC outlet to turn off and reset the monitor e When something is stuck on the bezel key becomes unresponsive Image Persistence e Image persistence is when a residual or ghost image of a previous image remains visible on the screen Unlike CRT monitors LCD monitors image persistence is not permanent but constant images being displayed for a long period of time should be avoided To alleviate image persistence turn off the monitor for as long as the previous image was displayed For example if an image was on the monitor for one hour and a residual image remains the monitor should be turned off for one hour to erase the image NOTE As with all personal
15. Caution Use the standard position VESA holes to attach the arm Thickness of Bracket Arm 2 0 3 2 mm 100 mm i EET 100 mm Weight of LCD assembly 6 6 kg Figure F 1 i aaan Additional VESA Holes for Lower Monitor Head Position Additional 4 VESA holes are provided for those users needing a lower monitor head position than that is available from the monitor stand in shipping configuration The monitor stand can be re attached by using the 4 screws to the lower position VESA holes NOTE 1 The monitor head tilt function may experience impaired operation when attached to the lower position VESA holes 2 The monitor head pivot function should not be used when attached to the lower position VESA holes 4 Screws M4 Additional 4 VESA Max Depth 8 5 mm L OOOOONNOOINMONNNNONNIANNNNANNNNNNNAN IMNON ININA 000000 yannoghoonnoonnonnnononnannnonnnana Mf D 0000000000000000000000000010101010110 Suu H g 20 o RO English 10 Controls OSD On Screen Display control keys on the front of the monitor function are as follows To access OSD menu touch any of the control keys To change signal input touch the SELECT key NOTE Exit OSD in order to change signal in
16. G Setting that boosts whole tones best suited for games that use vivid colorful images PHOTO Setting that optimizes contrast best suited for still images DYNAMIC Seiting that adjusts the brightness by detecting the screen s black areas and optimizes it NOTE This function is disabled when Color Control System is set to DICOM SIM SCREEN AUTO ADJUST Analog input only Automatically adjusts the image position H SIZE and FINE settings AUTO CONTRAST Analog input only Adjusts the image displayed for non standard video inputs LEFT RIGHT Controls horizontal image position within the display area of the LCD DOWN UP Controls vertical image position within the display area of the LCD H SIZE Analog input only Adjusts the horizontal size by increasing or decreasing this setting If the AUTO ADJUST function does not give you a satisfactory picture setting a further tuning can be performed by using the H SIZE function dot clock For this a Moir test pattern could be used This function may alter the width of the picture Use LEFT RIGHT key to center the image on the screen If the H SIZE is wrongly calibrated the result would look like the left drawing The image should be homogeneous THT i p gt f When H SIZE value is When H SIZE value is When H SIZE value is wrong improved correct English 13 FINE Analog input only Improves focus
17. NEC MultiSync EA294WMi User s Manual Index Warning Caulonia yuaeeobe cat Ea English 1 Registration ITO MMAN OM Gries tarteracannanaaatecsicdesicch a a a N English 2 Recommended US Gennana a r a r a A a N English 3 COMEN iaa E E N English 5 Oue kala a a a English 6 CONTOS riei e a T a e a eneteeeee ces eneuamenaceneteies English 11 SPEC aUo aeaa a English 18 FEAE Sia A aa wtt dleecamed naaeeaniencteberapadade tuatuaeesusaeane English 19 I POUDIOSMOOUNG sscctonsccatarcssthadame nance sactooumediaase duet sqessstesestenavensecedae tas N English 20 Using the Auto BrontinGSS TUMCU OM citetucst cciitraw stl ch aein a a a paced English 22 Using Picture by Picture PBP FUNCUON ntsataticedeutateciaesteae ter iaeida diana ied ered English 23 Using the Zoon FUNCIO M ries a T S T TA English 24 CONTO YNG aiaa ce me ee English 26 TOCO Cernihed Edge DIS lay SA EZ ua tstevesun eric tnaceed n E ste ucassioalnas English 27 Manufacturer s Recycling and Energy Information ccccseccecceeeeeceeeeeeseeeeeseeeeseeeeeeeeeeesaeeeeens English 28 WARNING TO PREVENT FIRE OR SHOCK HAZARDS DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE ALSO DO NOT USE THIS UNIT S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS THE PRONGS CAN BE FULLY INSERTED REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL AN CAUTION A N CAUTION TO
18. NG CARBON FOOTPRINT START TIME HUMAN SENSING SENSOR SETTING START TIME DY MODE Figure 3 When the AUTO BRIGHTNESS function is enabled the Brightness level of the screen changes automatically according to the lighting conditions of the room Figure 4 100 BRIGHTNESS range BRIGHTNESS level set for the monitor to use when ambient lighting level is low BRIGHTNESS level set for the monitor to use when ambient lighting level is high Bright condition area e a ee dark room bright condition bright Dark condition area Screen Brightness value by Auto Brightness function Figure 4 Lb Border between bright and dim lighting conditions set at factory L1 BRIGHTNESS level set for the monitor to use when ambient lighting level is high L1 gt Lb L2 BRIGHTNESS level set for the monitor to use when ambient lighting level is low L2 lt Lb L1 and L2 are the brightness levels set by the user to compensate for changes in ambient lighting English 22 Using Picture by Picture PBP Function This monitor can display split screens from two sources by using any one of the input combinations shown on page 15 NOTE Please see PBP MODE page 15 and PBP TYPE page 15 The following settings are set to be the same for both screens BRIGHTNESS AUTO BRIGHTNESS OFF MODE SETTING HUMAN SENSING VIDEO LEVEL OVER SCAN PROGRAMMABLE VOLUME SOUND INPUT VIDEO DETECT PBP MODE PBP TYPE RESPONSE IMPROVE OFF TIMER POWER
19. SAVE TIMER LED BRIGHTNESS DDC CI USB POWER LANGUAGE OSD TURN OFF OSD LOCK OUT HOT KEY SIGNAL INFORMATION SENSOR INFORMATION KEY GUIDE CARBON CONVERT SETTING CURRENCY SETTING CURRENCY CONVERT SETTING SETUP 1 Press MENU to show OSD menu MENU 2 Select PBP MODE then select LEFT or RIGHT as the adjustable screen Exit OSD in order to change signal input e VOLUME SOUND INPUT eVIDEO DETECT PBP MODE PBP TYPE RIGHT RESPONSE IMPROVE eOFF TIMER POWER SAVE TIMER eLED BRIGHTNESS DDC CI USB POWER eFACTORY PRESET 3 Press INPUT then select the input signal used by the selected screen INPUT 4 Return to 1 to select the input for the other screen e VOLUME SOUND INPUT eVIDEO DETECT PBP MODE ciad naii ID d ad LEFT RESPONSE IMPROVE OFF TIMER ePOWER SAVE TIMER LED BRIGHTNESS DDC CI USB POWER eFACTORY PRESET English 23 Using the Zoom Function Allows you to use the entire screen area significantly expanding the size Allows the picture displayed in the center to expand NOTE When in PBP MODE the sub picture is expanded or reduced automatically SETUP 1 Select FULL or ASPECT in EXPANSION to activate the Zoom function see page 14 EXPANSION OFF 2 Seta resolution via HIRESOLUTION or V RESOLUTION see page 14 Vertical expanding Horizontal expanding 3 The image position can be moved from the center to left or right by selecting LEFT RIGHT and u
20. adjust stand e Power Cord e Video Signal Cable DVI D to DVI D cable e Video Signal Cable Mini D SUB 15 pin to Mini D SUB 15 pin e USB Cable e Audio Cable 3 5 stereo mini plug e ControlSync Cable 2 5 stereo micro plug e Setup Manual e Base S Mini D SUB 15 pin to Mini D SUB 15 pin Power Cord WES Setup Manual USB Cable DVI D to DVI D cable ControlSync Cable Remember to save your original box and packing material to transport or ship the monitor 1 The type and number of power cords included will depend on the where the LCD monitor is to be shipped When more than one power cord is included please use the power cord that matches the AC voltage of the power outlet and has been approved by and complies with the safety standard of your particular country 2 Dual link DVI cable English 5 Quick Start To attach the Base to the LCD stand 1 Place monitor face down on a non abrasive surface Figure 1 J a al i Uf pot NOTE Handle with care when monitor facing down for avoiding damage to the front control keys 2 Please rotate the stand 90 degrees as shown in Figure 1 NOTE Handle with care when pulling the stand oe 3 Attach the base to the stand and lock screw at the base s bottom Figure 2 ecu NOTE Reverse this procedure if you need to re pack the monitor To connect the LCD monitor to your system follow these in
21. consumer audio video equipment Color Control Systems Allow you to adjust the colors on your screen and customize the color accuracy of your monitor to a variety of standards OSD On Screen Display Controls Allow you to quickly and easily adjust all elements of your screen image via simple to use on screen menus ErgoDesign Features Enhanced human ergonomics to improve the working environment protect the health of the user and save money Examples include OSD controls for quick and easy image adjustments tilt base for preferred angle of vision small footprint and compliance with MPRII and TCO guidelines for lower emissions Plug and Play The Microsoft solution with the Windows operating system facilitates setup and installation by allowing the monitor to send its capabilities such as screen size and resolutions supported directly to your computer automatically optimizing display performance Intelligent Power Manager System Provides innovative power saving methods that allow the monitor to shift to a lower power consumption level when on but not in use saving two thirds of your monitor energy costs reducing emissions and lowering the air conditioning costs of the workplace Multiple Frequency Technology Automatically adjusts monitor to the display card s scanning frequency thus displaying the resolution required FullScan Capability Allows you to use the entire screen area in most resolutions significantly expanding ima
22. disconnecting the ControlSync cable Do not use the ControlSync connectors for any purpose other than specified This value is not a directly adjusted output value This is adjusted relatively English 26 TCO Certified Edge Displays 1 2 Congratulations This product is TCO Certified for Sustainable IT Ge TCO Certified is an international third party sustainability certification for IT products TCO Certified ensures that the manufacture use and recycling of IT products reflect environmental social and economic responsibility Every TCO Certified product model is verified by an accredited independent test laboratory TCO Certified Edge is a supplemental certification recognizing best in class products in a specific sustainability attribute This product has also been verified to meet all the criteria in TCO Certified including Corporate Social Responsibility Socially responsible production working conditions and labor law in manufacturing country Energy Efficiency Energy efficiency of product and power supply Energy Star compliant where applicable Environmental Management System Manufacturer must be certified according to either ISO 14001 or EMAS Minimization of Hazardous Substances Limits on cadmium mercury lead amp hexavalent chromium including requirements for mercury free products halogenated substances and hazardous flame retardants Design for Recycling Coding of plastics for easy recycling Limit on
23. display devices NEC DISPLAY SOLUTIONS recommends using a moving screen saver at regular intervals whenever the screen is idle or turning off the monitor when not in use Message OUT OF RANGE is displayed screen is either blank or shows rough images only e Image is displayed only roughly pixels are missing and OSD warning OUT OF RANGE is displayed Either signal clock or resolution is too high Choose one of the supported modes e OSD warning OUT OF RANGE is displayed on a blank screen Signal frequency is out of range Choose one of the supported modes Image is unstable unfocused or swimming is apparent e Signal cable should be completely attached to the computer e Use the OSD Image Adjust controls to focus and adjust display by increasing or decreasing the fine adjustment When the display mode is changed the OSD Image Adjust settings may need to be readjusted e Check the monitor and your display card with respect to compatibility and recommended signal timings e If your text is garbled change the video mode to non interlace and use 60Hz refresh rate LED on monitor is not lit no blue or amber color can be seen e Power Switch should be in the ON position and power cord should be connected e Increase LED BRIGHTNESS adjustment Picture is not as bright e Make sure ECO MODE and AUTO BRIGHTNESS are turned off e lf the brightness fluctuates make sure AUTO BRIGHTNESS is turned off e Signal cable should be completely at
24. e Figure S 1 NOTE Handle with care when the monitor is facing down 4 Remove 2 bottom screws first Move stand left and right to remove bottom 2 screws Figure S 2 S 3 5 Remove 2 top screws NOTE In order to avoid stand drop when removing screws please support stand with your hand Remove the stand Figure S 4 The monitor is now ready for mounting in an alternate manner Figure S 1 Connect the cables to the back of the monitor ON Reverse this process to re attach stand NOTE Use only VESA compatible alternative mounting method Handle with care when removing stand NOTE Match TOP SIDE mark on stand to top side of the monitor head when re attaching stand Figure S 2 Figure S 3 Figure S 4 English 9 Mount Flexible Arm This LCD monitor is designed for use with a flexible arm 1 Follow the instructions on how Remove Monitor Stand for Mounting to remove the stand 2 Use the 4 screws removed from the stand to attach the arm to the monitor Figure F 1 Caution Use ONLY the screws 4 pcs that were removed from the stand to avoid damage to the monitor or stand To meet the safety requirements the monitor must be mounted to an arm which guaranties the necessary stability under consideration of the weight of the monitor The LCD monitor should only be used with an approved arm e g GS mark
25. equipment specified above conforms C to the technical standards as specified in the FCC Rules English 2 Recommended use Safety Precautions and Maintenance FOR OPTIMUM PERFORMANCE PLEASE NOTE THE FOLLOWING WHEN SETTING UP AND USING THE LCD COLOR MONITOR e DO NOT OPEN THE MONITOR There are no user serviceable parts inside and opening or removing covers may expose you to dangerous shock hazards or other risks Refer all servicing to qualified service personnel e Do not spill any liquids into the cabinet or use your monitor near water e Do not insert objects of any kind into the cabinet slots as they may touch dangerous voltage points which can be harmful or fatal or may cause electric shock fire or equipment failure e Do not place any heavy objects on the power cord Damage to the cord may cause shock or fire e Do not place this product on a sloping or unstable cart stand or table as the monitor may fall causing serious damage to the monitor e The power supply cord you use must have been approved by and comply with the safety standards of your country Type HO5VV F 3G 1mm should be used in Europe e In UK use a BS approved power cord with molded plug having a black 5A fuse installed for use with this monitor e Do not place any objects onto the monitor and do not use the monitor outdoors e Do not bend power cord e Do not use monitor in high temperatured humid dusty or oily areas e Do not cover vent o
26. ge size VESA Standard Mounting Interface Allows users to connect your MultiSync monitor to any VESA standard third party mounting arm or bracket No Touch Auto Adjust Analog input only Automatically adjusts the monitor to optimal settings upon initial setup SRGB Color Control A new optimized color management standard which allows for color matching on computer displays and other peripherals The SRGB which is based on the calibrated color space allows for optimal color representation and backward compatibility with other common color standards Adjustable stand with pivot capability Adds flexibility to your viewing preferences USB 2 0 hub adds excitement to your computing by connecting you to digital cameras scanners and more Human Sensor Shifts to a lower power consumption level when a person leaves the monitor saving your monitor energy costs NaViSet Software offers an expanded and intuitive graphical interface allowing you to more easily adjust OSD display settings via mouse and keyboard Environmental Impact Annual typical maximum operating carbon footprint of this monitor world wide average is approximately 69 1 kg calculated by rated wattage x 8 hours per day x 5 days a week x 45 weeks per year x Power to Carbon conversion factor conversion factor is based on OECD publication of global CO2 emissions 2008 Edition This monitor has a manufacturing carbon footprint of approximately 41 kg Note The manufacturing and ope
27. ightness of surrounding environment changes the monitor will also change USB Hub does not operate e Check to make sure the USB cord is properly connected Refer to your USB devise User s Manual e Check if the USB upstream port on the monitor is connected to the USB downstream port on the computer And make sure the computer is ON Human sensor does not work e f human icon on SENSOR SETTING HUMAN SENSING is located on vermilion color it is detected that there is person e Make sure there is no object in front of Human sensor e Make sure there is no equipment which radiating infrared rays in front of monitor ControlSync does not work e Check to make sure that ControlSync cable is connected correctly e Check to make sure that ControlSync cable is not in loop connection e Master monitor should be connected OUT connector only e Please use provided ControlSync cable e You can use up to 5 sub monitors via ControlSync Message PBP LIMITATION is displayed e Check to make sure the signal combination and set the optimized combination for split screen see page 15 English 21 Using the Auto Brightness function The brightness of the LCD screen can be set to increase or decrease depending on the amount of ambient light within the room If the room is bright the monitor becomes correspondingly bright If the room is dim then the monitor will dim accordingly The purpose of this function is to make the viewing experience
28. locks out the access to all OSD control functions except for BRIGHTNESS CONTRAST and VOLUME To activate the OSD Lock Out function enter the OSD menu select OSD LOCK OUT then press SELECT and RIGHT simultaneously To deactivate press SELECT and LEFT simultaneously HOT KEY When this function is activated PBP MODE BRIGHTNESS and VOLUME can be adjusted without entering the OSD menu by using the front keys ON The PBP touch key on the bezel is enabled and can toggle among PBP MODE settings The Left Right key adjusts the brightness level The Up Down key adjusts the volume level OFF The HOT KEY function for PBP Left Right and Up Down functions are disabled SIGNAL INFORMATION If you select ON monitor displays VIDEO INPUT MENU after changing the input If you select OFF monitor doesn t display VIDEO INPUT MENU after changing the input SENSOR INFORMATION If you select ON monitor displays HUMAN SENSOR ON message If you select OFF monitor doesn t display HUMAN SENSOR ON message KEY GUIDE If you select ON the Key Guide appears on screen when the OSD control menu is accessed English 16 DATA COPY To initiate data copy from the master monitor to the sub monitor s select DATA COPY and touch SELECT A PROCEEDING indicator will appear on the screen NOTE This function is only intended for the master monito
29. mark of NEC Display Solutions Ltd in Austria Benelux Denmark France Germany Italy Norway Spain Sweden U K ENERGY Star is a U S registered trademark All other brands and product names are trademarks or registered trademarks of their respective owners As an Enercy Star Partner NEC Display Solutions of America Inc has determined that this product meets the Enercy Star guidelines for energy efficiency The ENercy Star emblem does not represent EPA endorsement of any product or service Ta DisplayPort and DisplayPort Compliance Logo are trademarks owned by the Video Electronics Standards D Association Himi HIGH DEFINITION MULTIMEDIA INTERFACE HDMI the HDMI logo and High Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries MHL and the MHL logo are a trademark registered trademark or service mark of MHL K mo f L LLC in the United States and or other countries j Mobile High Definition Link e The intended primary use of this product is as an Information Technical Equipment in an office or domestic environment e The product is intended to be connected to a computer and is not intended for the display of television broadcast signals ENERGY STAR English 1 Registration Information Canadian Department of Communications Compliance Statement This Class B digital ap
30. n monitor e Vibration can damage the backlight Do not install where the monitor will be exposed to continual vibration e lf monitor or glass is broken do not come in contact with the liquid crystal and handle with care e To prevent damage to the LCD monitor caused by tipping over due to earthquakes or other shocks make sure to install the monitor in a stable location and take measures to prevent falling Immediately turn off the power unplug your monitor from the wall outlet and move to a safe location then refer servicing to qualified service personnel under the following conditions If the monitor is used in this condition the monitor may cause fall fire and electric shock e lf the monitor stand has been cracked or peeled e lf the monitor has been wobbled e lf the monitor has an unusual odor e When the power supply cord or plug is damaged e f liquid has been spilled or objects have fallen into the monitor e lf the monitor has been exposed to rain or water e lf the monitor has been dropped or the cabinet damaged e lf the monitor does not operate normally by following operating instructions e Allow adequate ventilation around the monitor so that heat can properly dissipate Do not block ventilated openings or place the monitor near a radiator or other heat sources Do not put anything on top of monitor The power cable connector is the primary means of detaching the system from the power supply eee The monitor should
31. n most common situations DICOM SIM The white point color temperature and the gamma curve are set to a DICOM simulation PROGRAMMABLE The brightness of grayscale can be changed to your preference by downloading the application software NOTE When MOVIE GAMING or PHOTO is selected as the DV MODE NATIVE is selected automatically as the seven color preset and cannot be changed Tools VOLUME Controls the volume of the speakers or headphones To mute the speaker output touch the PBP RESET key SOUND INPUT This function selects AUDIO INPUT HDMI or DISPLAYPORT NOTE When using split screen the SOUND INPUT setting can change which audio input signal is routed through the built in speakers LEFT Outputs the audio that is associated with the left video signal HDMI or DisplayPort only RIGHT Outputs the audio that is associated with the right video signal HDMI or DisplayPort only AUDIO INPUT Outputs the audio from the input audio jack on the back of the monitor left side of display below the USB ports VIDEO DETECT Selects the method of video detection when more than one video inputs are connected FIRST When current video input signal is not present then the monitor searches for a video signal from the other video input port If the video signal is present in the other port then the monitor switches the video source input port to the new found video source automatically The monitor will not look for other video sig
32. nals while the current video source is present NONE The monitor will not search the other video input port unless it is turned on PBP MODE Activates PICTURE BY PICTURE split screen function and selects the priority adjustable screen OFF PBP is OFF Shows a single screen LEFT PBP is ON Shows 2 screens The left screen is select as priority screen which is adjustable RIGHT PBP is ON Shows 2 screens The right screen is select as priority screen which is adjustable NOTE When selected LEFT or RIGHT each screen is available to be adjusted see page 24 PBP TYPE Selects the size of the sub picture used in PICTURE BY PICTURE split screen mode AUTO Shows 2 screens based on INPUT RESOLUTION and EXPANSION setting of the priority adjustable screen selected in PBP MODE The available signals used for PBP mode are limited to the following combinations only CENTER Splits 2 screens divided evenly from the center Right picture Source D SUB1 DVI1 3 D SUB2 DVI2 4 HDM DP D SUB1 DVI1 Pinte D SUB2 n n Yes ve Yes ves Source DVI2 No No Yes Yes Yes Yes HDMI DP No No Ye Ye Yes Ye 1 When PBP TYPE is selected to AUTO the left picture is displayed on the left half of the display only 2 When PBP TYPE is selected to AUTO the right picture is displayed on the right half of the display only 3 DualLink 4 SingleLink English 15 RESPONSE IMPROVE Turns the Respo
33. ndard signal is sent to the monitor the Energy Saving mode is activated The monitor enters a single Energy Saving mode Normal Operation at TCO testing 38 W Default setting USB Audio sleeping Bue Energy Saving Mode 0 80 W Off Mode 0 44 W WEEE Mark European Directive 2002 96 EC Within the European Union EU wide legislation as implemented in each Member State requires that waste electrical and electronic products carrying the mark left must be disposed of separately from normal household waste This includes monitors and electrical accessories such as signal cables or power cords When you need to dispose of your NEC display products please follow the guidance of your local authority or ask the shop where you purchased the product or if applicable follow any agreements made between yourself and NEC Outside the European Union The mark on electrical and electronic products only applies to the current European Union Member States If you wish to dispose of used electrical and electronic products outside the European Union please contact your local authority so as to comply with the correct disposal method English 28
34. nit is Euro You can adjust currency setting to Euro icon from US dollar by touching the LEFT or RIGHT key in Current setting item 4 Select CURRENCY CONVERT SETTING by touching the UP or DOWN key 5 Adjust CURRENCY CONVERT SETTING by touching the LEFT or RIGHT key This initial Euro setting is Germany of OECD 2007 Edition Please check receipt of French s electricity prices or OECD data for French French of OECD 2007 Edition was 0 12 Information Provides information about the current resolution display and technical data including the preset timing being used and the horizontal and vertical frequencies Indicates the model and serial numbers of your monitor OSD Warning OSD warning menus disappear when EXIT is selected NO SIGNAL This function gives a warning when there is no horizontal or vertical sync After power is turned on or when there is a change of input signal the NO SIGNAL window will appear OUT OF RANGE This function gives a recommendation of the optimized resolution and refresh rate After the power is turned on or there is a change of input signal or if the video signal doesn t have proper timing the OUT OF RANGE menu will appear PBP LIMITATION This function gives a recommendation of the optimized signal combinations for split screen When the PBP LIMITATION window appears set the optimized signal combination See page 15 English 17 S
35. nse Improve function on or off Response Improve may reduce blurring that occurs in some moving images OFF TIMER Monitor will automatically power down when you have selected a pre determined amount of time Before powering off a message will appear on the screen asking if you want to delay the turn off time by 60 minutes Touch any OSD key to delay the power down time POWER SAVE TIMER POWER SAVE TIMER allows the monitor to turn off automatically after continuing power saving mode for 2 hours LED BRIGHTNESS You can adjust the blue LED brightness DDC CI This function allows the DDC CI function ON or OFF USB POWER Selects a power relation of USB AUTO Power is supplied to USB downstream port depending on related power condition ON Power is always supplied to USB downstream port even when in power save mode or power OFF NOTE Power consumption depends on connected USB even when a monitor s power is off FACTORY PRESET Selecting FACTORY PRESET allows you to reset all OSD control settings back to the factory settings Individual settings can be reset by touching the PBP RESET Key MENU Tools LANGUAGE Selects the language used by the OSD OSD TURN OFF The OSD control menu will stay on as long as it is in use You can select how long the monitor waits after the last touch of a key to shut off the OSD control menu The preset choices are 10 120 seconds by 5 second increments OSD LOCK OUT This control completely
36. ontrolSync OUT connector ControlSync icon The ControlSync icon will appear on the upper left of the OSD menu in the sub monitor Do not connect IN IN or OUT OUT Do not make loop connection Once the monitors are connected turn the master monitor s power button off and on to check if ControlSync operates correctly Master Monitor Sub Monitor 1 Sub Monitor 2 y unnnonnoonnornsannonnannnannoannnonnannnnnnnornnanaanoannnannonnoornornnonaan lN f M mumun N g o o E o o E E IE E I s B 2 8 28 ggr OUT Black OUT _ Black Gray l wy ControlSync cable Up to 5 sub monitors IN Gray Black Gray i S S S ControlSync cable The following settings can be controlled by ControlSync ECO TOOLS BRIGHTNESS VOLUME CONTRAST ECO MODE AUTO BRIGHTNESS BLACK LEVEL OFF MODE SETTING SCREEN ENU TOOLS COLOR Other settings Power Control DC switch Ambient Sensor Human Sensor Result Audio Mute NOTE Only the master monitor s human sensor and ambient sensor are active Please do not cover these sensors Turn the monitor s power off before connecting
37. paratus complies with Canadian ICES 003 Cet appareil numerique de la classe B est conforme a la norme NMB 003 du Canada C UL Bears the C UL Mark and is in compliance with Canadian Safety Regulations according to CAN CSA C22 2 No 60950 1 FCC Information 1 Use the attached specified cables with the MultiSync EA294WMi L292VK monitor so as not to interfere with radio and television reception 1 The power supply cord you use must have been approved by and comply with the safety standards of U S A and meet the following condition Power supply cord Non shield type 3 conductor Length 1 8m Plug shape ay Cx U S A 2 Please use the supplied shielded video signal cable 15 pin mini D SUB to D SUB cable or DVI D to DVI D cable Use of other cables and adapters may cause interference with radio and television reception This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television recep
38. pecifications Monitor Specifications LCD Module Input Signal DisplayPort DisplayPort Connector DVI DVI D 24pin DVI D 18pin VGA 15pin Mini D sub HDMI MHL HDMI MHL Connector Load current Display Colours Synchronization Range Horizontal Vertical Viewing Angle Left Right Up Down Image Formation Time Resolutions Supported Active Display Area Load Current AUDIO AUDIO Input Speakers Practical Audio Output ControlSync IN available up to 5 sub monitors OUT Power Supply Current Rating Dimensions Landscape Portrait Height Adjustment Weight Environmental Considerations Operating Temperature Humidity Altitude Storage Temperature Humidity Altitude Diagonal Viewable Image Size Native Resolution Pixel Count Landscape Horiz Vert Portrait Horiz Vert USB Hub I F Port STEREO Mini Jack DisplayPort Connector HDMI MHL Connector Headphone Output STEREO Mini Jack MultiSync EA294WMi 73 02 cm 28 7 inches 73 02 cm 28 7 inches 2560 x 1080 Digital RGB Digital RGB Digital RGB Analog RGB Sync Digital YUV Digital RGB Maximum 0 5A 16 777 216 31 5 kHz to 83 0 kHz Analog 31 5 kHz to 83 0 kHz Digital 56 Hz to 75 Hz 89 CR gt 10 89 CR gt 10 6 ms Gray to gray Typ 720 x 400 VGA text 640 x 480 60 Hz to 75 Hz 800 x 600 56 Hz to 75 Hz 832 x 624 75 Hz 1024 x 768 60 Hz to 75 Hz 1152 x 870
39. put RESET PBP 8 DOWN v SELECT EXIT LEFT RIGHT 1 Detects the level of ambient lighting allowing the monitor to make adjustments to various Human Sensor settings resulting in a more comfortable viewing experience Do not cover this sensor 4 INPUT SELECT Enters the OSD Control menu Enters OSD sub menus Shows a switching menu of input source when not in the OSD menu 5 MENU EXIT Accesses OSD menu Exits the OSD sub menu Exits OSD Control menu Hold the button for a few seconds when not in the OSD menu to activate RESTORE in CUSTOMIZE SETTING 6 LEFT RIGHT Navigates to the left or right through the OSD Control menu You can adjust the BRIGHTNESS directly while the OSD menu is off 7 UP DOWN Navigates up or down through the OSD Control menu You can adjust the VOLUME directly when not in the OSD Control menu 8 PBP RESET Resets the OSD controls back to factory settings Activates the Auto Adjust function if held for 3 seconds while the OSD menu is off analog input only Selects PBP MODE when OSD menu is off 1 When HOT KEY function is OFF this function is disabled 2 PBP MODE menu Touch the LEFT RIGHT to select a single or a priority adjustable screen of split screen When PBP MODE is OFF a single screen will be displayed PBP MODE LEFT RIGHT English 11 EJ ECOTOOLS BRIGHTNESS Adjusts the overall image and background screen
40. pward or downward by selecting UP DOWN see page 13 Move to left or right Move upward or downward NOTE When showing 2 screens the input resolution of the main adjustable image is prioritized A The right image is set to be the main one In this case the priority image is set to be on the right side with black area shown The input resolution for the image on the left side is decreased Se SS SSS SS SS SF FEE EES S _ G English 24 B The left image is set to be the main one In this case the priority image is set to be on the left side The size of the image on the right side with black area is reduced one ODO G OGOGO OGO G Bh ee OG G Boe oe oe To enlarge the split images use the following procedures to reduce the black area and enlarge the split images 1 In case A a priority image is set to be on the right side The size of the black area can be reduced by adjusting the resolution see page 14 m gt HS G Ee amp amp amp Ga ce G 2 EF HII gt I_HEPP EPH EF_HEPEWSPFESE I a gt English 25 ControlSync 1 Connect the master monitor with a sub monitor via a ControlSync cable 2 5 into ControlSync IN OUT 2 Follow the steps of DATA COPY When the setting of the master monitor is adjusted it will be copied and sent to the connected sub monitor s automatically 3 Up to 5 sub monitors can be daisy chained via ControlSync NOTE Connect the master monitor via C
41. r in ControlSync All of the settings specified in the ControlSync chart see page 26 will be copied from the master monitor to the sub monitor s CUSTOMIZE SETTING Store the current settings for easy recovery To store current settings Touch SELECT After a warning message appears touch RESET current settings are stored To restore settings Hold MENU for 3 seconds or more while the OSD menu is off ECO Information CARBON SAVINGS Displays the estimated carbon savings information in kg CARBON USAGE Displays the estimated carbon usages information in kg This is the arithmetic estimation not actual measurement value COST SAVINGS Displays the electricity cost savings in balance CARBON CONVERT SETTING Adjusts the carbon footprint factor in the carbon saving calculation This initial setting is based on the OECD 2008 Edition CURRENCY SETTING Displays electricity pricing in 6 currency units CURRENCY CONVERT SETTING Displays electricity savings in kW hour US Currency is default NOTE This model s initial setting is Currency US and its Currency Convert setting 0 11 This setting can be changed by using the ECO information menu If you want to use the French setting please refer to steps below 1 Touch the Menu key and select the ECO information menu using the LEFT or RIGHT key 2 Select CURRENCY SETTING item by touching the UP or DOWN key 3 The French currency u
42. rating carbon footprints are calculated by a unique algorithm developed exclusively by NEC for its monitors and are accurate at the time of printing NEC reserves the right to publish updated carbon footprint values HDCP High bandwidth Digital Content Protection HDCP is a system for preventing illegal copying of video data sent over a Digital Visual Interface DVI If you are unable to view material via the DVI input this does not necessarily mean the display is not functioning properly With the implementation of HDCP there may be cases in which certain content is protected with HDCP and might not be displayed due to the decision intention of the HDCP community Digital Content Protection LLC ControlSync Follow the steps of DATA COPY and copy the settings from the master monitor to the sub monitors by connecting the ControlSync cable When the setting of the master monitor is adjusted it is sent to the sub monitors automatically providing easy setting controls in a multiple monitor environment CUSTOMIZE SETTING Allows to store the current settings and recover stored settings English 19 Troubleshooting No picture e The signal cable should be completely connected to the display card computer e The display card should be completely seated in its slot e The monitor does not support DisplayPort converter signal e Front Power Switch and computer power switch should be in the ON position e The monitor will automatically
43. rlaced signals with a vertical refresh rate of 60 Hz e Do not use primary color blue on a dark background as it is difficult to see and may produce eye fatigue due to insufficient contrast Cleaning the LCD Panel e When the LCD is dusty please gently wipe with a soft cloth e Please do not rub the LCD panel with hard or coarse material e Please do not apply pressure to the LCD surface e Please do not use OA cleaner as it will cause deterioration or discoloration on the LCD surface Cleaning the Cabinet e Unplug the power supply e Gently wipe the cabinet with a soft cloth e To clean the cabinet dampen the cloth with a neutral detergent and water wipe the cabinet and follow with a dry cloth NOTE Many plastics are used on the surface of the cabinet DO NOT clean with benzene thinner alkaline detergent alcoholic system detergent glass cleaner wax polish cleaner soap powder or insecticide Do not touch rubber or vinyl to the cabinet for a long time These types of fluids and fabrics can cause the paint to deteriorate crack or peel For more detailed information on setting up a healthy work environment write to the American National Standard for Human Factors Engineering of Computer Workstations ANSI HFES 100 2007 The Human Factors Society Inc P O Box 1369 Santa Monica California 90406 English 4 Contents Your new NEC monitor box should contain the following e MultiSync monitor with a tilt swivel pivot height
44. rt Cable HDMI Cable D SUB Cables Audio Cable D SUB Cables Audio Cable ControlSync Cables ControlSync Cables USB Cables USB Cables al N Figure C 2 Figure C 3 Cable not included 7 Connect one end of the power cord to the AC inlet on the back of the monitor and the other end to the power outlet NOTE Please refer to Caution section of this manual for proper selection of AC power cord English 7 8 Turn on the computer then turn on the monitor by pressing the power sign on the front bezel Figure E 1 9 No Touch Auto Adjust automatically adjusts the monitor to optimal settings upon initial setup For further adjustments use the following OSD controls e AUTO CONTRAST Analog input only e AUTO ADJUST Analog input only Refer to the Controls section of this User s Manual for a full description of these OSD controls NOTE If you have any problems please refer to the Troubleshooting section of this User s Manual Figure E 1 Raise and Lower Monitor Screen The monitor may be raised or lowered in either portrait or landscape mode To raise or lower screen place a hand on each side of the monitor and lift or lower to the desired height Figure RL 1 NOTE Handle with care when raising or lowering the monitor screen Figure RL 1 Screen Rotation Before rotating disconnect power cord and
45. s D 130 mm 5 1 inches Landscape orientation 10 4 mm 0 4 inches Portrait orientation 9 6 kg 21 2 lbs Without stand 6 6 kg 14 6 Ibs 5 C to 35 C 41 F to 95 F 20 to 80 O to 6 562 Feet 0 to 2 000 m 10 C to 60 C 14 F to 140 F 10 to 85 O to 40 000 Feet 0 to 12 192 m 1 Interpolated Resolutions When resolutions are shown that are lower than the pixel count of the LCD module text may appear different This is normal and necessary for all current flat panel technologies when displaying non native resolutions full screen In flat panel technologies each dot on the screen is actually one pixel so to expand resolutions to full screen an interpolation of the resolution must be done NOTE Technical specifications are subject to change without notice English 18 Features DisplayPort DisplayPort is designed to be the future ready and scalable solution for high performance digital display connectivity It enables the highest resolutions the fastest refresh rates and deepest color depths over standard cables MHL MHL Mobile High Definition Link is designed for a mobile audio video interface for directly connecting portable consumer electronics to high definition displays HDMI HDMI is designed to be the future ready scalable solution for high performance digital display connectivity It enables the highest resolutions the fastest refresh rates and deepest color depths over standard cables especially for
46. structions NOTE Make sure to read Recommended Use page 3 before installation i ie i 1 Turn off the power of your computer 2 For a PC or MAC with DVI digital output Connect the DVI signal cable to the connector of the display card in your system Figure A 1 Tighten all screws For a PC with Analog output Connect a 15 pin mini D SUB signal cable to the Figure 2 connector of the display card in your system Figure A 2 For a MAC Connect a Macintosh cable adapter not included to the computer then attach the 15 pin mini D SUB signal cable to the Macintosh cable adapter Figure A 3 MD NOTE Some Macintosh systems do not require any Macintosh cable adapter For a PC with DisplayPort output Connect the DisplayPort cable to the connector of the display card in your system Figure A 4 For a PC with HDMI output Connect the HDMI cable to the connector of the display card in your system Figure A 5 c m ogg Macintosh Cable Adapt Figure A 1 Figure A 2 fot cluded encapter Figure A 3 i Ih 2 LPT TL R LI i I DisplayPort cable Figure A 4 HDMI cable Figure A 5 not included not included NOTE 1 Please use a DisplayPort cable with DisplayPort logo 2 When removing the DisplayPort cable hold down the top button to release the lock English 6 3 Place hands on each side of the monitor to tilt the LCD panel 30 degree angle and lift
47. tached e LCD brightness degradation occurs due to long term usage or extreme cold conditions e When using an HDMI input please change VIDEO LEVEL Display image is not sized properly e Use the OSD Image Adjust controls to increase or decrease the Coarse adjustment e Check to make sure that a supported mode has been selected on the display card or system being used Please consult display card or system manual to change graphics mode e When using an HDMI input please change OVER SCAN e Check to make sure that the appropriate resolution has been selected in HKRESOLUTION and V RESOLUTION English 20 No Video e f no video is present on the screen turn the Power Key off and on again e Make certain the computer is not in a power saving mode touch the keyboard or mouse e Some video cards do not output video signal when monitor is turned OFF ON or disconnect connect from the AC power cord under low resolution with DisplayPort e When using an HDMI input please change OVER SCAN No Sound e Make sure the speaker cable is proper connected e Check to see if mute is activated e Check the VOLUME in the OSD menu e Check selected OSD s Tools to SOUND INPUT when DisplayPort or HDMI is in use Brightness variations over time e Change AUTO BRIGHTNESS to OFF and adjust brightness NOTE When AUTO BRIGHTNESS is set to ON the monitor automatically adjusts brightness based on the environment When the br
48. tion which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult your dealer or an experienced radio TV technician for help If necessary the user should contact the dealer or an experienced radio television technician for additional suggestions The user may find the following booklet prepared by the Federal Communications Commission helpful How to Identify and Resolve Radio TV Interference Problems This booklet is available from the U S Government Printing Office Washington D C 20402 Stock No 004 000 00345 4 Declaration of Conformity This device complies with Part 15 of FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation U S Responsible Party NEC Display Solutions of America Inc Address 500 Park Boulevard Suite 1100 Itasca Illinois 60143 Tel No 630 467 3000 Type of Product Display Monitor Equipment Classification Class B Peripheral Model MultiSync EA294WMi L292VK We hereby declare that the
49. up to the highest position 4 Connect all cables to the appropriate connectors Figure C 1 When using the USB cable connect the B type connector to the USB upstream port on the right back side of the monitor and the A type connector to the downstream port on the computer Figure C 1a If using the cord from a USB device plug into one of the downstream ports of the monitor NOTE Incorrect cable connections may cause abnormal operation damage display quality components of LCD module and or shorten the module s life 30 Tilt USB Downstream Y Highest Stand Q Headphone Position Figure C 1a ControlSync IN OUT Audio In putN USB Upstream USB Downstream HDMI MHL D SUB2 D SUB1 DVI D1 DualLink DVI D2 SingleLink DisplayPort Figure C 1 See page 26 5 To keep the cables neatly organized place them into the cable management system that is built into the stand Place the cables in the hooks firmly and evenly Figure C 2 and Figure C 3 NOTE Cable cover is not removable 6 Please check that you can still rotate raise and lower the monitor screen after you have installed the cables LLL OO aaa l 7 A Power Cord m i D DVI Cables Power Corda DVI Cables DisplayPort Cable HDMI Cable DisplayPo
Download Pdf Manuals
Related Search