iHome iPL10
Contents
1. 6 presets P1 P6 to the number you wish to assign and then hold the Pil Dock Button until the selected preset number begins flashing in the display B Press the or Buttons to tune the radio to a desired station Hold briefly to have the radio autoscan search for the next clear station C Press the ll Dock Button to confirm the setting two confirmation beeps will confirm the setting and the preset number you wish to assign Repeat steps A C to preset up to 6 stations 4 To listen to a preset station use the Mode Button to select FM mode then press the PII Dock Button to choose the desired preset 5 Press the or Button on the unit to adjust the system volume USING THE UNIT IN OTHER COUNTRIES Different regions of the world use different FM radio frequency steps and ranges You will need to select the one that matches the standards in your region USA EUROPE JAPAN AUSTRALIA or CHINA The default setting is USA if you live in the US you may skip this section 1 Press and release the Power Button to turn on the unit then press and release the Mode Button as needed to cycle to FM radio mode 2 Press and hold the Mode Button for about 5 seconds until the region flashes in the lower part of the display and a beep sounds 3 Press the or Buttons as needed to set the display to your region USA EU Europe JPN Japan AUS Australia or CHN China 2 Press and release the Mode Button or no butto2. high Turn volume down on your device Sound source is distorted If the original sound file MP3 is old or of poor quality distortion and noise are easily noticed with high power speakers Try upgrading file from a trusted source such as iTunes Device doesn t charge up Unit is not properly connected to AC power Please make sure the unit is connected to a working power outlet The unit will not charge while operating on backup battery 11 IMPORTANT SAFETY TIPS When used in the directed manner this unit has been designed and manufac tured to ensure your personal safety However improper use can result in potential electrical shock or fire hazards Please read all safety and operating instructions carefully before installation and use and keep these instructions handy for future reference Take special note of all warnings listed in these instructions and on the unit 1 10 a k Water and Moisture The unit should not be used near water For example near a bathtub washbowl kitchen sink laundry tub swimming pool or in a wet basement Ventilation The unit should be situated so that its location or position does not interfere with its proper ventilation For example it should not be situated on a bed sofa rug or similar surface that may block ventilation openings Also it should not be placed in a built in installation such as a bookcase or cabinet which may impede the flow o
3. Model iPL10 stereo alarm clock to charge your iPod or iPhone iHome apps available on the App Store ORO QUESTIONS Visit www ihomeaudio com WELCOME Thank you for choosing the iPL10 from iHome This user guide will get you up and running quickly and provide helpful hints to maximize enjoyment For more information about this and other Home products please visit www ihomeaudio com Note that details on using iHome apps with this unit are not covered in this booklet For information on using Home apps please visit www ihomeaudio com apps GETTING STARTED This unit ships with the following items Please check to see that all items are present 1 iPL1O speaker system 2 100 240V Universal AC power adaptor FEATURES amp FUNCTIONS Backrest Top panel Lightning Dock Lightning Dock Play Pause Presets Button Volume Control Buttons Power On Off Button Mode Button Settings Buttons Time Set Sleep button Alarm button USB Play Pause Button snooze dimmer Snooze Dimmer Button Back panel DC Jack USB dock 6 oh 9V2 5A Ses iPod iPhone Display Time Display Volume Indicator Alarm AU AA 7 4 PM Indicator I I I I Oi Indicator E A ENE iPod H Indicator CA AY A oe eee WAKE TO zzz WAKE TO Indicator Pod Buzzer or Sleep Indicator Low Backup Battery Indicator 2 CONNECTING TO AC POWER This unit ope
4. Requiring Service The unit should be serviced by qualified service personnel when the power supply cable or plug has been damaged 2 objects have fallen into or liquid has been spilled into the enclosure the unit has been exposed to rain the unit has been dropped or the enclosure damaged the unit exhibits a marked change in performance or does not operate normally muou gt 12 MPORTANT SAFETY TIPS CONTINUED 12 Periods of Non use If the unit is to be left unused for an extended period of time such as a month or longer the power cable should be unplugged from the unit to prevent damage or corrosion 13 Servicing The user should not attempt to service the unit beyond those methods described in the user s operating instructions Service methods not covered in the operating instructions should be referred to qualified service personnel 14 Magnetic Interference This product s speakers contain powerful magnets which could cause interference or damage to sensitive equipment such as hard drives CRT televisions and monitors as well as medical scientific and navigational devices Keep this unit away from these products at all times A GUIDE TO PRODUCT SAFETY This device complies with Part 15 of the FCC Rules operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference tha
5. al wood and lacquered finish A cloth or other protective material should be placed between it and the furniture e Clean your unit with a soft cloth moistened only with mild soap and water Stronger cleaning agents such as Benzene thinner or similar materials can damage the surface of the unit 10 TROUBLESHOOTING Symptom Possible reason Solution Unit won t turn on AC adaptor isn t plugged into a working wall socket or not plugged into the power jack on back of the unit Plug the AC adaptor into a working wall socket and plug the connector into the supply jack on the unit Make sure any associated wall switch that controls the outlet the is ON Device does not respond to the unit and or device is playing but no sound comes out Unit is not properly connected to power source and or Power Button is not ON device is paused Make sure the unit is properly connected to AC power source Check that the Power Button is lit up indicating the unit is ON Try adjusting volume on unit and audio device Press the Mode Button to select the Lightning dock iPod USB or FM mode Also try pressing the Play Pause Button Erratic performance External interference Move unit away from potential sources of external interference such as computers modems wireless devices routers or fluorescent light No sound Volume is too low Turn volume up on your device Sound distorted Volume is too
6. already playing iPhone iPod to the USB dock on back of the unit using the cable that came with your device The unit will automatically turn on and you will hear the music playing from your iPhone iPod The iPhone iPod Icon will appear at the right side of the display indicating iPhone iPod playing mode Press the wor Buttons on the unit to adjust the system volume Note If the volume is too low on the iPhone iPod the unit may not detect that the iPhone iPod is in play mode Press the pil USB Button O play it Press again as needed to pause and resume play Press the or Buttons to go to the next or previous track hold to scan backwards or forwards within a track Press the Power Button to turn off the unit You can also turn the unit off by disconnecting a device playing through the USB dock NOTE Press the Mode Button to cycle from Lightning dock iPod to USB to FM radio modes LISTENING TO FM RADIO Tuning and Playing the Radio 1 Press and release the Power Button to turn on the unit then press and release the Mode Button as needed to cycle through dock USB and FM radio modes When FM mode is selected press the or Buttons to tune the radio to a desired station The current radio frequency appears in the bottom of the display Press the or Buttons for a few seconds to scan for the next clear station To memorize a station as a preset A Press the PI Dock Button as needed to step through the
7. ce Center 3 Enclose a photocopy of your sales receipt credit card statement or other proof of the date of purchase if within the warranty period Also include your name and address information a brief description for why the unit is being returned and the return authorization number No unit can be processed without a return authorization number 4 Write the return authorization number on the side of the shipping package and send the unit prepaid and insured to the Factory Service Center address authorized by SDI Customer Service Disclaimer of Warranty NOTE This warranty is valid only if the product is used for the purpose for which it was designed It does not cover i products which have been damaged by negligence or willful actions misuse or accident or which have been modified or repaired by unauthorized persons ii cracked or broken cabinets or units damaged by excessive heat iii damage to digital media players CD s or tape cassettes if applicable iv the cost of shipping this product to the Factory Service Center and its return to the owner This warranty is valid only in the United States of America and does not extend to owners of the product other than to the original purchaser In no event will SDI or any of its affiliates contractors resellers their officers directors shareholders members or agents be liable to you or any third party for any consequential or incidental damages any lost profits actual exemp
8. f air through the ventilation openings Heat The unit should be situated away from heat sources such as radiators heat registers stoves or other appliances including amplifiers that produce heat Power Sources The unit should be connected to a power supply only of the type described in the operating instructions or as marked on the appliance Power Cable Protection Power supply cables should be routed so that they are not likely to be walked on or pinched by items placed upon or against them It is always best to have a clear area from where the cable exits the unit to where it is plugged into an AC socket Cleaning The unit should be cleaned only as recommended See the Maintenance section of this manual for cleaning instructions Objects and Liquid Entry Care should be taken so that objects do not fall and liquids are not spilled into any openings or vents located on the product Attachments Do not use attachments not recommended by the product manufacturer Lightning and Power Surge Protection Unplug the unit from the wall socket and disconnect the antenna or cable system during a lightning storm or when it is left unattended and unused for long periods of time This will prevent damage to the product due to lightning and power line surges Overloading Do not overload wall sockets extension cords or integral convenience receptacles as this can result in a risk of fire or electric shock Damage
9. g dock iPod is selected press the or Buttons to set the Lightning dock volume can be set from 5 40 The alarm will wake you to the last track played on your docked iPhone or iPod Wake to USB If wake to USB is selected press the or Buttons to set the USB dock volume can be set from 5 40 The alarm will wake you to the last track played on the iPhone or iPod connected to the USB dock Wake to radio If wake to FM is selected press the or Buttons to select a radio station to wake to then confirm your selection by pressing the Alarm Button Press the or Buttons to set the FM radio alarm volume can be set from 5 40 Wake to Buzzer f wake to Buzzer is selected press the or Buttons to choose HI or LO buzzer alarm volume 4 Press the Alarm Button to exit and confirm alarm settings An alarm icon will appear on the display indicating that the alarm is set and armed REVIEWING AND RESETTING THE ALARM Press and release the Alarm Button at any time to review the current alarm settings To toggle the alarm on or off press the Alarm Button as needed When the alarm icon is displayed the alarm is armed on Press the d Power Button or Alarm Button when the alarm is sounding to reset it to come on again at the same time the next day Press the Alarm Button again to turn off disarm the alarm The alarm icon will disappear CHARGING YOUR PHONE OR POD Gently dock your iPhone or P
10. hten the battery door screw Note Make sure you dispose of battery properly see your local regulations WARNING Lithium batteries can explode or cause burns if disassembled shorted recharged exposed to water fire or high temperatures Do not place loose batteries in a pocket purse or other container containing metal objects mix with used or other battery types or store with hazardous or combustible materials Store in cool dry ventilated area Follow applicable laws and regulations for transport and disposal SETTING THE TIME TIME SYNC 8 MANUAL TIME SETTING TIME SYNC This unit is equipped with auto sync By default the unit will sync to the time on your iPhone or newer iPod iPod touch iPod nano and iPod Classic older iPod models such as iPod mini do not support this feature whenever you dock it in the Lightning dock OR connect via the USB port located on back of the unit When successful the updated time will appear on the display If sync is unsuccessful try to sync again using a different iPhone or iPod If sync still doesn t work set the time manually see below SETTING THE TIME MANUALLY 1 Press and hold the Time Set Button until MAN or SYNC flashes in the display and one beep sounds If SYNC is displayed press the or Buttons so MAN appears in the display indicating manual time setting mode Press and release the Time Set Button The time will flash in the displa
11. lary or punitive damages Some states do not allow limitations on implied warranties or exclusion of consequential damages so these restrictions may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from state to state Your acknowledgement and agreement to fully and completely abide by the above mentioned disclaimer of warranty is contractually binding to you upon your transfer of currency money order cashier s check or credit card for purchase of your SDI product Questions Visit www ihomeaudio com Toll Free Customer Service 1 877 446 6301 SDI Technologies 2013 All rights Reserved iPL10 01102013 A Printed in China
12. n within 10 seconds to exit the radio frequency setting mode Two beeps will confirm radio frequency setting SNOOZE DIMMER OPERATION 1 To program a custom snooze duration during normal operation when alarm is not sounding press and hold the Snooze Dimmer Button until the display flashes then press the and Buttons on the unit to adjust the snooze time to 1 29 minutes 2 Press the Snooze Dimmer Button on the PL10 after the alarm sounds The alarm will be silenced and will come on again in about 9 minutes default You may repeat this cycle several times during the one hour alarm cycle 3 During normal operation when alarm is not sounding press the Snooze Dimmer Button to control the brightness high medium low and off settings of the LCD display SLEEP MODE Sleep mode lets you sleep to your playing Lightning docked or USB connected iPhone or iPod or to FM radio Press the Sleep Button as needed to cycle to the desired sleep duration 120 90 60 30 or 15 minutes or OFF turns sleep mode off Press the w or Button on the unit to adjust sleep listening level The unit will revert to normal volume level when sleep mode ends Press the Sleep Button during sleep to view the remaining sleep time press again to set sleep to next lower sleep duration MAINTENANCE e Place the unit on a level surface away from sources of direct sunlight or excessive heat Protect your furniture when placing your unit on a natur
13. od into the flexible Lightning dock located on the top of the unit OR connect an iPhone or iPod to the USB dock on back of unit using the cable that came with your device While your iPhone iPod is docked in the unit and or connected via the USB dock and the unit is connected to AC power it recharges until fully charged The unit will not overcharge your iPhone iPod Note Please make sure your iPhone iPod is properly docked into the unit Failure to do so may damage your iPhone iPod LISTENING TO YOUR iPHONE iPOD USING THE LIGHTNING DOCK OR USB DOCK USING THE LIGHTNING DOCK 1 Dock your already playing iPhone iPod The unit will automatically turn on and you will hear the music playing from your iPhone iPod The iPhone iPod Icon will appear at the right side of the display indicating iPhone iPod playing mode 2 Press the or Buttons on the unit to adjust the system volume Note If the volume is too low on the iPhone iPod the unit may not detect that the iPhone iPod is in play mode Press the PII Dock Button to play it Press again as needed to pause and resume play 3 Press the or Buttons to go to the next or previous track hold to scan backwards or forwards within a track 4 Press the Power Button to turn off the unit You can also turn the unit off by undocking a playing device NOTE Press the Mode Button to cycle from Lightning dock iPod to USB to FM radio modes USING THE USB DOCK 1 Connect your
14. oducts a division of SDI Technologies Inc hereafter referred to as SDI warrants this product to be free from defects in workmanship and materials under normal use and conditions for a period of one 1 year from the date of original purchase Should this product fail to function in a satisfactory manner it is best to first return it to the store where it was originally purchased Should this fail to resolve the matter and service still be required by reason of any defect or malfunction during the warranty period SDI will repair or at its discretion replace this product without charge This decision is subject to verification of the defect or malfunction upon delivery of this product to the Factory Service Center authorized by SDI Customer Service The product must include proof of purchase including date of purchase An out of warranty fee for service will be charged for units that are received without proof of purchase Before returning this product for service please first replace the batteries if applicable with fresh ones as exhausted or defective batteries are the most common cause of problems encountered If service is still required 1 Call SDI Customer Service at 1 877 446 6301 for Return Authorization and for the address of the Factory Service Center 2 Remove the batteries if applicable and pack the unit in a well padded heavy corrugated box SDI is not responsible for damage that occurs during shipping to the Factory Servi
15. rates on AC power using the included 100V 240V universal AC adaptor for charging and playing your iPhone or iPod Place unit on a stable surface Plug the power adaptor into the DC jack on back of the unit and the other end into a working wall socket You can now charge your iPhone or iPod BACKUP BATTERY The iPL10 ships with a CR2450 battery installed for backup to provide continuous alarm operation and clock settings in the event of a power failure Remove the pull tab from the battery compartment on the bottom of the unit before use If a power failure occurs or the AC cord is accidentally disconnected the display backlight will not remain lit but current time and alarm time settings will be temporarily maintained Otherwise you must reset the time and alarm settings Note The Ca Battery Low icon is located at the right side of clock display When the backup battery is low and needs to be replaced the Battery Low icon will flash To replace follow steps below BACKUP BATTERY CONTINUED 1 Please make sure the AC adaptor is connected Otherwise all settings may be lost during battery replacement 2 Use a Phillips screwdriver to open the backup battery compartment door located on the bottom of the unit 3 Remove the exhausted battery Insert a new CR2450 battery by easing it under the tabs in the battery well and pressing down Make sure the side marked is facing up 4 Close the battery compartment door and tig
16. t may cause undesired operation Warning Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment NOTE This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help This Class B digital apparatus complies with Canadian ICES 003 Cet appareil num rique de la classe B est conforme a la norme NMB 003 du Canada 13 LIMITED 1 YEAR WARRANTY iHome Pr
17. y Press the or Buttons to set the correct time hold for rapid adjustment Make sure you are setting the time to the correct AM or PM time The PM indicator appears at the upper left of the display there is no AM indicator NOTE The time can be set to standard 12 hour time AM and PM or to 24 hour time sometimes called military time To toggle between 12 and 24 modes press and release the U Alarm Button located on top of the unit at any time during manual time setting mode Press and release the Time Set Button to confirm the current time setting two beeps will sound and exit time setting mode SETTING AND USING THE ALARM SETTING THE ALARM This unit lets you wake to an iPhone or iPod docked in the Lightning dock iPod USB connected device USB FM radio or to the built in buzzer alarm The alarm will sound for 60 minutes or until reset turned off 1 Press and hold the Alarm Button until the alarm time display flashes with one beep 2 Press the or Buttons to adjust the display to the desired alarm time hold for rapid adjustment Remember to set the correct AM or PM alarm time 3 Press the Alarm Button to confirm the alarm time The WAKE TO indicator will flash on the display Press the or Buttons to toggle among wake to Lightning dock USB FM radio or buzzer then press US the Alarm Button to access volume setting for the selected alarm source Wake to iPod If wake to Lightnin
Download Pdf Manuals
Related Search