Kenwood Electronics KDC-BT73DAB radio receiver
Contents
1. and wiring this product requires skills and experience For safety s sake leave the mounting and wiring work to professionals lt If you experience any problem during installation consult your Kenwood dealer Disconnect the battery s negative terminal before installing the unit Insulate unconnected wires with vinyl ape or other similar materials To prevent a short circuit do not remove the caps on he ends of the unconnected wires and erminals lt Be sure to ground this unit to the car s chassis again after mounting f the fuse blows first make sure the wires are not touching other parts to cause a short circuit and then replace the old fuse with one with a new the same rating When connecting only two speakers connect the connectors either to both of the front output terminals or to both of the rear output terminals do not mix front and rear terminals For example if you connect the connector of the left speaker to a front output terminal do 10 Quick Start Guide not connect the connector to a rear output terminal Connect the speaker wires correctly to the corresponding terminals The unit may be damaged or fail to work if you share the wires or ground them to any metal part in the car Do not use your own screws Use only the supplied screws Using wrong screws could damage the unit f your car s ignition key switch does not have an ACC position connect the ignitio2. disc Open the Disc slot cover upward and press 4 Removing USB device iPod Switch to a source other than USB iPod and Aha Radio and then remove the USB device Data contained in the USB device iPod may be damaged if you remove it when it is used as the active source Removing SD card KDC 50575D only 1 2 Press the Release button and detach the Faceplate Push the SD card until it clicks and then remove your finger from the card The card pops up so that you can pull it out with your fingers Attaching the Faceplate English 7 Listening to the radio Digital radio SRC Control knob 4 KENWOOD Q 2 lt P gt Selecting a tuner source Press SRC to select TUNER or DIGITAL RADIO KDC BT73DAB only Refer to Source selection page 5 Selecting a band FM or AM Tuner only ress A Selecting a station service ress ka a or gt gt The seek mode can be changed Refer to lt 9 5 Tuner setting gt or lt 10 9 Digital Radio setting gt in Instruction manual Station preset memory 1 Press A to select a band Tuner only 2 Press 4 4 or Pi to select the station service you want to save in the station preset memory TUNER Press Q 45 DIGITAL RADIO Press A 45 twice Press Q 45 again to enter the Mix Station preset mode In this mode diffe
3. 73DAB KDC BT53U only Digital radio antenna Yellow Battery Accessory 8 Blue White ower Control KDC BT73DAB only Orange White Dimmer Red gnition ACC Black Earth Ground Connection urple Rear Right 4 urple Black Rear Right Microphone Accessory KDC BT53U only Gray Front Right Gray Black Front Right White Front Left White Black Front Left Green Rear Left Speaker Impedance Green Black Rear Left 4 80 See Connecting the ISO Connector page 1 Red A 7 Pin Red Ignition wire Yellow Battery wire Connector A Yellow A 4 Pin Connector B KDC BT73DAB only 12 Quick Start Guide only USB connector 0 8m To USB device USB maximum power supply current DC5Vz 1A Fuse 10 Mes Microphone Accessory KDC BT73DAB only B Wiring harness Accessory QD If no connections are made do not let the wire come out from the tab Blue White Power control Antenna control wire P CONT 1 ANT CONT Connect either to the power control terminal when using the optional power amplifier or to the antenna control terminal in the vehicle Light Blue Yellow Steering remote control wire To use the steering wheel remote control feature an exclusive remote adapter not REMOTECONT supplied that matches your car is required When connec
4. Do not touch the feeder terminal of the element Also do not apply any glass cleaner with the A on the antenna film and paste lt Do not touch the feeder terminal or the pasting surface adhesive side of the amplifier When installing the antenna on the right side Match the protrusion with A Earth sheet Accessory 4 Accessory 5 English 17 KDC BT73DAB only Installing the Digital radio antenna When installing the antenna on the left side Accessory 5 Accessory 4 pus Earth sheet Match the protrusion with A 8 Remove the film covering the earth sheet and paste the earth sheet on the metal part of the vehicle Provide sufficient leeway for the earth sheet so that it does not interfere with the interior parts front pillar cover Also take care that the interior parts do not interfere with the amplifier Front glass Accessory 5 Front pillar Interior part Earth sheet 9 wire the antenna cables Use cord clamper Accessory to secure the antenna to the pillar at several locations 18 Quick Start Guide lt Take the following precautions when passing the antenna cable inside the front pillar where the air bag is installed Install the amplifier part of the antenna cable in front or above the air bag so that the antenna and the air bag do not interfere Front pillar The front pill
5. KENWOOD KDC BT73DAB KDC BT53U KDC 5057SD CD RECEIVER Quick Start Guide JVCKENWOOD Corporation 068 Digital Audio Broadcasting C Bluetooth o Made for 9 iPod LliPhone 2012 JVC KENWOOD Corporation B59 2186 00 00 E Contents About the Quick Start Guide 2 Before USE 2 Preparations sensencon 4 General operations Playing music CD USB SD iPod Listening to the radio Digital radio Hands free phoning ss 9 Before installation s 10 Connecting wires to terminals Installing Removing the unit Installing the Microphone unit 15 Installing the Digital radio antenna 15 eo 19 About the Quick Start Guide This Quick Start Guide describes basic functions of this unit For functions not described in this Guide refer to the Instruction Manual on the following website manual2 jvckenwood com edition im362 To refer to the Instruction Manual a browser such as Internet Explorer 7 or later Firefox 3 6 or later Chrome 20 or later Safari 5 1 or later iOS Safari 4 0 or later or Android 2 2 or later is required 2 Quick Start Guide Before use A WARNING To prevent injuries or a fire take the following precautions Stop the car before operating the unit lt To prevent a short circuit never put or le
6. ar cover is secured with a special clip which may need to be replaced when the front pillar cover is removed Contact your vehicle dealer for details on replacing the front pillar cover and availability of replacement parts Interior part Appendix About Audio file ayable Audio files AAC LC m4a mp3 WMA wma WAV wav of USB device SD card Playable disc media CD R RW ROM Playable disc file formats SO 9660 Level 1 2 Joliet Long file name Playable USB devices USB mass storage class Playable SD cards SD card lt 2 GB SDHC card lt 32 GB lt Playable USB device SD card file systems FAT12 FAT16 FAT32 The online manual about audio files is put on the site www kenwood com cs ce audiofile Models of iPods iPhones that can be connected to this unit Made for iPod touch 4th generation iPod touch 3rd generation iPod touch 2nd generation iPod touch 1st generation iPod classic iPod with video iPod nano 6th generation iPod nano 5th generation iPod nano 4th generation i i i i i i i i od nano 2nd generation od nano 1st generation hone 4S hone 4 hone 3GS hone 3G iPhone For information on the compatibility with od nano 3rd generation iPod iPhone software visit www kenwood com cs ce ipod Requirements Aha Requirements for listening to the Aha are as follows iPhone or iPod touch Use Apple iPh
7. ave any metallic objects such as coins or metal tools inside the unit A CAUTION Adjust the volume so that you can hear sound outside the car Driving with the volume adjusted to a too high level may cause an accident Wipe off the dirt on the panel with dry silicon or soft cloth Failure to observe this precaution may result in damage to the monitor or unit Cleaning the connector The unit may not function properly if the connector between the unit and faceplate are dirty Detach the faceplate and clean the connector with a cotton swab gently being careful not to damage the connector Condensation When the car is air conditioned moisture may collect on the laser lens This may cause disc read errors In this case remove the disc and wait for the moisture to evaporate Notes lt If you experience problems during installation consult your Kenwood dealer When you purchase optional accessories check with your Kenwood dealer to make sure that they can work with your model and in your area Characters that conform to ISO 8859 1 can be displayed Characters that conform to ISO 8859 5 or ISO 8859 1 can be displayed Refer to Russian of 12 7 Initial settings Instruction Manual The Radio Data System feature won t work where the service is not supported by any broadcasting station USB rating is indicated on the main unit under the detachable faceplate Abo
8. display may be inapplicable English 3 Preparations Control knob Volume knob Release Canceling the Demonstration mode Cancel the Demonstration mode when you use the unit for the first time after installation 1 Press Control knob to cancel the Demonstration mode when the message To cancel DEMO Press the volume knob appears approx 15 seconds 2 Turn Control knob to select YES and then press Control knob The Demonstration mode can also be canceled in the Function Setting mode Refer to 12 6 Demonstration mode setting in Instruction manual 4 Quick Start Guide Press the CD Release button Remove the faceplate at once after pressing the Release button otherwise it can fall down due to vibration The faceplate is a precision component of the unit and can be damaged by shocks or jolts Keep the faceplate in its case while detached Do not place the faceplate and case in areas exposed to direct sunlight excessive heat or humidity Also avoid places with too much dust or the possibility of water splashing General operations SRC Control knob USB terminal KENWOOD A ILS i E JJ Auxiliary input Power 5 Function of KDC BT53U To turn
9. drop it KDC BT73DAB KDC BT53U only Installing the Microphone unit gt Check the installation position of the microphone Accessory 3 Clean the installation surface Install the microphone Lay the cable up to the unit with it secured at several positions using tape or the like Install the microphone as far as possible from the cell phone JUN N Accessory 3 Fix the cable with a commercial item of tape Remove the separator of the microphone and stick the microphone to the place shown above Adjust the direction of the microphone to the driver KDC BT73DAB only Installing the Digital radio antenna A CAUTION This film antenna is exclusively for use inside the vehicle Do not install at the following locations Where it may block driver s view Where it may obstruct operation of safety devices such as air bags On movable glass surface such as rear hatch Signal strength will decrease at the following locations On IR reflecting glass or where covered with mirror type glass film Where it overlaps with genuine radio antenna pattern Where it overlaps with window heating wires At side of vehicle e g door front quarter window Onrear window When glass that blocks radio signals e g IR reflecting glass thermal insulation glass is used Reception may decrease due to noise when windshield wiper air conditioner or motor is turned on Receptio
10. located nearby can interfere with communication due to a too strong signal Installation accessories IM KDC BT73DAB only KDC BT53U only Connecting the ISO Connector The pin arrangement for the ISO connectors depends on the type of vehicle you drive Make sure to make the proper connections to prevent damage to the unit The default connection for the wiring harness is described in 1 below If the ISO connector pins are set as described in 2 make the connection as illustrated Please be sure to reconnect the cable as shown 2 below to install this unit to the Volkswagen vehicles etc 1 When the 7 pin red is connected with the ignition and the A 4 pin yellow is connected to the constant power supply of the vehicle s ISO connector default Ignition cable A 7 Pin Red Red gt Unit Vehicle gt Battery cable A 4 Pin Yellow Yellow 2 When the 7 pin red is connected to the constant power supply and the 4 pin yellow is connected with the ignition of the vehicle s ISO connector Ignition cable A 7 Pin Red Red gt 005 5 Unit Vehicle E3535 Battery cable A 4 Pin Yellow Yellow English 11 Connecting wires to terminals Connector Function Guide Pin Numbers for Cable Colour Functions ISO Connectors External Power e gt D3 FM AM antenna input JASO KDC BT
11. lose the Disc slot cover Playing a USB device iPod Connect a USB device or iPod to the USB terminal as shown above When it is connected the source is switched automatically and playback starts You can connect the iPod or USB device to either one of the USB terminals provided at the front and rear of this unit If you connect it to the rear USB terminal the REAR USB indicator stays lit 1 optional accessories 6 Quick Start Guide 4 A V REAR USB indicator USB Terminal Playing SD card 50575 only 1 Press the Release button and detach the Faceplate 2 Hold the SD card as shown below and insert it into the SD card slot until it Clicks Ec 27 SD card commercially available a P A c N lt gt 3 Reattaching the Faceplate 44 Press SRC to select SD source Selecting an audio file folder Press A or W Selecting a song track or file ress ka a or gt Fast forwarding or fast backwarding a song track or file ress and hold 444 or gt Pause and play a song track or file Press and hold Q 45 Music search You can search for the song you want to play 1 Press Q 45 2 Search for a song Operation type Operation Selecting items Turn Control knob Determining selection Press Control knob Press Q4 Returning to previous item To cancel music search in audio files or iPod Press and hold Q 45 Ejecting
12. n may decrease depending on the direction of the broadcast station with respect to the vehicle antenna lt Be sure to check the installation location of film antenna Accessory 4 before installing Film antenna cannot be re pasted Thoroughly wipe oil and dirt from the pasting surface with the included cleaner Accessory Do not bend or damage the film antenna Accessory Warm the pasting surface by turning on the heater for example before applying It may not be possible to install on some type of vehicle Check the cable routing of the film antenna Accessory and amplifier Accessory 5 before pasting English 15 KDC BT73DAB only Installing the Digital radio antenna Installation overview Antenna cable 3 5 m WA D The antenna should be installed on the passenger side for safety Use cord clamper Accessory to secure the antenna to the pillar at several locations The direction of the antenna film Accessory changes depending on whether the film antenna is installed on the right side or left side Separate the antenna film Accessory 4 from the ceramic line black part at the top of the front glass by 150 mm Also place it about 70 mm inside the ceramic line at the side end of the front glass where the earth sheet of the amplifier can be pasted on the metal part of the front pillar Separate from other antennas by at least 100 mm Do not
13. n wires to a power source that can be turned on and off with the ignition ey If you connect the ignition wires to a constant voltage power source as with battery wires the battery may die f the console has a lid make sure to install the unit so that the faceplate will not hit the lid when it is closed or opened After the installing the unit check whether the brake lamps blinkers wipers etc on the car are working properly Mount the unit so that the mounting angle is 30 or less Reception may become poor if there are metal objects near the Bluetooth antenna KDC BT73DAB KDC BT53U only unit KDC BT73DAB This unit has the cooling fan to decrease the internal temperature Do not mount the unit in a place where the cooling fan of the unit are blocked Blocking these openings will inhibit the cooling of the internal temperature and result in malfunction For Good Reception To assure good reception note the following Communicate with the cell phone within the line of sight distance of 10 m 30 ft The communication range becomes shorter depending on the surrounding environment The communication range also becomes shorter when there is an obstacle between this unit and the cell phone The above maximum communication range 10 m is not always assured A broadcast station or walkie talkie
14. one or iPod touch running iOS4 or later Search for aha in the Apple iTunes App Store to find and install the most current version of the Aha application on your device iPhone iPod touch connected to this unit with a KCA iP102 Android Use Android OS 2 2 or later Download the Aha application to your smartphone from the Google Play Bluetooth must be built in and the following profiles must be supported SPP Serial Port Profile A2DP Advanced Audio Distribution Profile NOTE In the application on your device log in and create a free account with Aha lt Internet connection by LTE 3G EDGE or WiFi Because Aha is a third party service the specifications are subject to change without prior notice Accordingly compatibility may be impaired or some or all of the services may become unavailable Some Aha functionality cannot be operated from this unit English 19 KENWOOD
15. our cell phone is completed the phone book of the cell phone is automatically downloaded o this unit If the phone book has not been downloaded to this unit operate the cell phone to download it Dialing a number in the phone book Dial the phone number in the phone book of your cell phone If the phone book has not been downloaded to this unit operate the cell phone to download it 1 Press 2 Turn Control knob to select Phone Book and then press Control knob 3 Turn Control knob to select a name and then press Control knob 4 Turn Control knob to select a phone number 5 Press 6 Answering a phone call Press Disconnecting a call Press English 9 Before installation A WARNING The unit can only be installed in a car with a 12V DC power supply negative ground If you connect the ignition wire red and the battery wire yellow to the car chassis ground you may cause a short circuit that in turn may start a fire Always connect those wires to the power source running through the fuse box A CAUTION Use the power harness enclosed with this unit for connecting power Using a power harness enclosed with other models can cause malfunction Install this unit in the console of your vehicle Do not touch the metal parts of this unit during and shortly after use of the unit etal parts such as the heat sink and enclosure become hot Mounting
16. paste the amplifier Accessory on the ceramic line black part around the front glass Because there is not enough adhesion 16 Quick Start Guide Determining the antenna installation location When installing the antenna on the left side pillar Earth sheet 70 mm N Accessory 4 Accessory 5 When installing the antenna on the right side ka Accessory 8 Front pillar et Where the earth sheet of amplifier unit Accessory 8 can be pasted on the metal part of the front pillar Antenna Installation 1 Check the installation location 2 Clean the area where antenna film Accessory 2 amplifier unit Accessory and earth sheet are pasted with the included cleaner Accessory The coating on the metal surface need not be removed Wait until the glass surface is completely dry before pasting lt If the glass surface is cold such as during winter warm it with defroster or dryer 3 Remove the separator tag of antenna film horizontally and paste the antenna on the front glass Remove the separator gently Do not touch the pasting surface adhesive side of the antenna film 4 Remove the separator tag 1 of antenna film vertically and paste the antenna gently while applying pressure 5 After pasting rub the element in the glass surface in the direction of the arrow shown in the figure to bond it 6 Remove the application film tag III
17. rent bands and tuner sources FM AM Digital Radio etc can be saved in the same preset layer which allows you to recall a desired station without switching between bands and or tuner sources Maximum of 6 stations can be preset in the Mix Station preset mode 8 Quick Start Guide 4 Turn Control knob to select preset number FM Digital Radio 1 18 AM 1 6 and then press and hold Control knob Recalling the stations in the memory 1 Press A to select a band Tuner only 2 Press 0 4 3 Turn Control knob to select a preset number FM Digital Radio 1 18 AM 1 6 and then press Control knob n the Mix Station preset mode band names of tuner sources are displayed as ollows FM FM broadcast station AM AM broadcast station DR Digital Radio service Function of KDC BT73DAB KDC BT53U Hands free phoning Control knob KENWOOD 1 Pairing a Bluetooth device You can pairing your Bluetooth device in this unit 1 Operate the Bluetooth device to request his unit for connection The name of this unit KDC HHHE appears on the Bluetooth device Press the volume knob appears 2 Press Control knob Connection to your Bluetooth device starts Pairing Success appears a while ater and then the previous source is selected When registration of y
18. the power ON press SRC Fubetion oFKDE S85 73D To turn the power OFF press and hold Volume SRC Turn Control knob to adjust the sound Source selection MSS Pressing SRC repeatedly switches USB terminal STON seres A USB device or iPod can be connected Source Display The CA U1EX Max 500mA or KCA iP102 Standby STANDBY optional accessories is recommended igital radio DIGITAL RADIO to connect a USB device or iPod uner TUNER Auxili 1 t SB device connected to front USB USB FRONT pues devicecan b ermina N E ted with a st plug 3 5 SB device connected to rear USB USB REAR stereo erminal iPod connected to front USB terminal iPod FRONT iPod connected to rear USB terminal iPod REAR aha of iPod connected to front USB FRONT erminal 121b aha of iPod connected to rear USB aha REAR eminal 2 aha of device connected via aha uetooth 281 Bluetooth audio 9 BT AUDIO spia SD pai Cp Auxiliary Input AUX This source can be selected only when it can be played 2 Function of KDC BT73DAB English 5 Playing music CD USB SD iPod 0 4 Release Playing a disc Open the Disc slot cover upward Insert a disc in the Disc slot When it is inserted the source is switched automatically and playback starts C
19. ting to the Kenwood navigation system Refer to your navigation manual When connecting to a car telephone To connect the terminal that is grounded when the telephone rings or during conversation KDC 5057SD only English 13 Brown Mute control wire MUTE Installing Removing the unit Installation Bend the tabs of the mounting sleeve with a screwdriver or the like and attach it in place Make sure that the unit is installed securely in place If the unit is unstable it may malfunction for example the sound may skip Removing the trim plate 1 Engage the catch pins on the extraction key 2 and release the two locks on the upper part of frame Lift up and pull the frame forward as shown in the figure Accessory 2 2 When the upper part of frame is removed remove the lower part of frame The frame can be removed from the bottom side in the same manner 14 Quick Start Guide Removing the unit 1 Remove the trim plate with reference to Removing the trim plate 2 Remove the faceplate 3 Insert the two extraction keys Accessory 2 deeply into the slots on both sides as shown 4 Lower the extraction key toward the bottom and then pull out the unit halfway while pressing the extraction key towards the inside Be careful to avoid injury from the catch pins on the extraction key 5 Pull the unit all the way out with your hands being careful not to
20. ut the discs used with this unit This unit can only play the CDs with The discs cannot be used A disc that is not round A disc with coloring on the recording surface or a disc that is dirty Arecordable rewritable disc that has not been finalized For the finalization process refer to the instruction manual that came with your disc writing software or your disc recorder An 8 cm 3 inch disc An attempt to insert using an adapter can cause malfunction Handling discs Do not touch the recording surface of the disc Do not stick tape etc on the disc or use a disc with tape stuck on it Do not use any accessories for the disc Do not use any solvents to clean discs Use a dry silicon or soft cloth Clean the disc by moving the cloth outward from the center of the disc When removing a disc from this unit pull it out horizontally lt If the center hole or outside rim of a disc has burrs remove them before inserting a disc How to reset your unit If the unit fails to operate properly press the Reset button The unit returns to the factory settings Reset button The illustrations of the display and panel appearing in this manual are examples used to explain more clearly how the controls are used Therefore what appears on the display in the illustrations may differ from what appears on the display on the actual equipment and some of the images on the
Download Pdf Manuals
Related Search