EK Water Blocks 3831109868065
Contents
1. Terminal interconnect to your graphics cards water blocks 1 Remove the preinstalled FC Single Terminal from the water block using 2 5mm Allen key by unfastening three M4 Screws 2 Save the O ring gaskets and M4 Screws from the FC Single Terminal 3 Install OR 15x1 mm O ring gaskets in grooved slots on the EK FC Terminal interconnect Make sure the gaskets are installed correctly Each water block or blank link requires two 2 gaskets 4 Secure the EK FC Terminal interconnect with M4x28 DIN7984 Screws enclosed using the enclosed Allen hex key 2 5mm 5 If necessary plug all unused Terminal ports using appropriate EK FC Terminal Blank Links Serial or Parallel depending on the type of your bridge When using EK FC Terminal Blank Links make sure you follow installation quides provided with the Blank Links 6 Plug all unneeded G1 4 threaded ports using Allen hex key 6mm if needed and install inlet outlet fittings EX recommends EK PSC and EK CSQ compression fittings OR 15xlmm Ul all EK FC Terminal series interconnect Screw M4x28 DIN 984 HIT ATTENTION I1 DO NOT OVERTIGHTEN THE SCREWS DOING SO WILL RENDER YOUR WATER BLOCK USELESS Once the feel the screw grab use no more than of the turn VERY IMPORTANT NOTICE Once the installation is completed it is a recommended practice to test the cooling circuit for leaks prior to powering up the computer We recommend a 24 hour leak test prior to poweri2. CkKWD Installation manual for EK FC Terminal system This product is intended for installation only by expert users Please consult with a qualified technician for installation Improper installation may result in damage to your equipment EK Water Blocks assumes no liability whatsoever expressed or implied for the use of these products nor their installation The following instructions are subject to change without notice Please visit our web site at www ekwb com for updates Before installation of this product please read important notice disclosure and warranty conditions printed on the back of the box Before you start using this product please follow these basic guidelines 1 Please carefully read the manual before through before beginning with the installation process 2 Please remove your motherboard from the computer to assure safest mounting process in order to prevent any possible damages to your CPU and or motherboard s circuit board PCB 3 The EK High Flow and EK PSC and EK CSQ type fittings require only a small amount of force to screw them firmly in place since the liquid seal is ensured by the rubber O ring gaskets The use of corrosion inhibiting coolants is always recommended for any liquid cooling system VERY IMPORTANT NOTICE READ THIS Do not over tighten the screws during assembly process Over tightening of the screw may damage the thread in the block s Top stripping the M4 thread or cracking the top rendering th
3. e blocks top useless Sample picture showing EK FC Terminal TRIPLE Parallel Serial or successive flow Parallel flow Water starts flowing initially through first Water flows through all blocks block continues to second block and ends simultaneously With such configuration up with the third block each water block gets one third of all Whole system flow is lower compared to flow Total system flow is higher parallel flow due to higher restriction compared to serial or successive flow It is of highest importance to use correct inlet and outlet port configuration Not using the correct ports may result in water bypassing the water blocks instead of flowing through the water blocks As a result the bypassed graphics card will overheat and may get damaged beyond repair l No inlet or y Inlet or outlet X outlet possible i possible Optional outlet or Outlet or inlet gt possible inlet To use this port use G1 45 Extender EAN 3831109845165 4 l l l l l l l l l l l l l l l l l l l l l l ha All disclosures notices and warranty conditions are being written on the EKWB website Please read terms of use Released on 15 of March 2013 Revision 1 1 PLEASE NOTE 1 Only one port must be used as inlet and one port as outlet 2 Ports can be exchanged meaning inlet can be used as outlet and at the same time outlet can be used as inlet Please take the following steps for installing any EK FC
4. ith aggressive additives or other improper liquids REQUI RED TOOLS Allen hex key 6mm amp 2 5mm both enclosed For support please visit www ekwb com support For product suggestion please visit thinkcell ekwb com All disclosures notices and warranty conditions are being written on the EKWB website Please read terms of use Released on 15 of March 2013 Revision 1 1
5. ng up the computer Do not test the water block using tap water pressure This will rupture the top of the housing and render the block unusable and will void your warranty While all efforts have been made to provide the most comprehensive tutorial possible EK Water Blocks assumes no liability expressed or implied for any consequential damage s occurring to your equipment as a result of using EK Water Blocks cooling products either due to errors or omissions on our part in the above instructions or due to failure or defect in the EK Water Blocks cooling products WARRANTY Our products are warranted against defects in materials or workmanship for a period of 24 months beginning from the date of delivery to the final user During this period products will be repaired or have parts replaced at our discretion provided that 1 the product is returned to the agent from whom it was purchased 11 the product has been purchased by an end user and has not used for commercial purposes HI the product has not been misused handled carelessly or used in a manner other than in accordance with the instructions provided describing its installation and proper use This warranty does not confer rights other than those expressly set out above and does not cover any claims for consequential loss or damage This warranty is offered as an extra benefit and does not affect your statutory rights as a consumer This warranty is voided if the product comes in contact w
Download Pdf Manuals
Related Search