EK Water Blocks 3831109857199
Contents
1. OF THE THERMAL PADS PRIOR TO INSTALLATION ongina thermal compound until the components and Replacement thermal pads Thermal Pad A 0 5 mm 100 x 16 mm Thermal Pad B 0 5 mm 75 x 50 mm circuit board are completely clean Apply thermal compound lightly coat MVIDIA GPU chip with for example GELID GC Extreme thermal grease EKWB 1 Thermal pad A 0 5 mm 75 recommends to apply thermal grease in cross form for for memory IC best performance see sample picture 16 1 1j 1 1j 1 1 1j 1 2 Thermal pad B 0 5 mm for VRM MOSFET STEP 3 INSTALLING THE WATER BLOCK 1 PLACING THERMAL PADS ON PCB Place thermal pads on chips so that numbers on chips match size of thermal pads EKWB made sure users have more than enough pads to cover all surfaces that need to be covered to make block fully functional EKWB recommends using small drops of electrically non conductive for example Arctic Cooling MX 2 MX 4 or GELID GC Extreme thermal grease on each phase regulator that is being covered with thermal pad in order to even further improve the thermal performance of the EK FC Titan series water block Repeat the procedure on the back side of the PCB All disclosures notices and warranty conditions are being written on the EKWB website Please read terms of use Released on 4 of March 2013 Revision 1 0 2 PLACING THE BLOCK TO THE GRAPHICS CARD Carefully position the water 3 ATTACHING THE BLOCK TO THE GRAPHI2. the EKWB website Please read terms of use Released on 4 of March 2013 Revision 1 0
3. CS CARD By using Philips block with preinstalled 2 5 mm standoffs on to the graphics card During this process screwdriver screw in enclosed M3x4 DIN 7985 screws EKWB recommends users to please make sure you align mounting holes on PCB with holes on the water block Also start tightening the screws around the GPU core and continue outwards Always use pay attention not to use too much force by pressing block down to PCB Chip dies are a plastic washer under each and every screw prone to cracking Screw M3x4 DIN 7985 If necessary temporarily remove the water block to check for uniform surface contact between the block and the components pay special attention to the VRM section of the graphics card Check whether the water block makes contact with the intended integrated circuit Then repeat sub steps in previous section to re attach the block In case you fail to obtain a good contact please check again your thermal pad thickness or contact our support service at http www ekwb com support Use one M3x6 screw one PVC washer and one M3 nut to secure the I O also known as PCI bracket firmly to the circuit board This will allow the computer chassis to carry the weight of the water block thus reducing the tension to the PCI express slot Tighten the screw with Philips head screwdriver while holding the M3 nut with your thumbs firmly Screw in the fittings in the G1 4 threaded openings on plastic top of the water block EKWB recommends u
4. a bracket required only on certain models Kal _ a eg im A ARAARA STEP 2 cont PREPARING YOUR GRAPHIC CARD 2 cont REMOVING STOCK COOLER Remove all encircled screws All heat sink assembly screws 2 CLEANING THE PCB Carefully detach the original stock cooler should be removed including self adhesive washers on both sides of the PCB if present There are up after removing all screws securing it to the board Wipe off the to 19 screws on the back of the graphics card Depending on the manufacturer a Torx T6 head screwdriver remains by using non abrasive cloth or qtip as shown on sample might be needed to complete this step photo of the original thermal compound until the components and circuit board are completely clean EKWB recommends the use of rs Renn EARANN denatured alcohol for removing TIM leftovers G e000 cco 0000 000 EKA oss r pa g gt H rp oh J OOD ea ts Pe gt s on sens gee goeeces Seege Seen eeewreueenree Se een ean ananaanana Pa G Eg uma oorpore wht wee ae inn eGR Gaa nr a UAwM me if a a e l 4 CUTTING THERMAL PADS Your block comes with thermal pads some of which are already pre cut Others 3 APPLYING THERMAL COMPOUND Wipe off the have to be cut to smaller chunks in order to cover all the VRM components such as MOSFETs and drivers PLEASE deal ou a bami or qtip of the REMOVE THE PROTECTIVE FOIL FROM BOTH SIDES
5. ekwbD Installation and mounting manual for EK FC Titan Original CSQ water block This product is intended for installation only by expert users Please consult with a qualified technician for installation Improper installation may result in damage to your equipment EK Water Blocks assumes no liability whatsoever expressed or implied for the use of these products nor their installation The following instructions are subject to change without notice Please visit our web site at www ekwb com for updates Before installation of this product please read important notice disclosure and warranty conditions printed on the back of the box Before you start using this product please follow these basic guidelines 1 Please carefully read the manual before through before beginning with the installation process 2 Please remove your motherboard from the computer to assure safest mounting process in order to prevent any possible damages to your CPU and or motherboard s circuit board PCB 3 The EK High Flow and EK PSC type fittings require only a small amount of force to screw them firmly in place since the liquid seal is ensured by the rubber o ring gaskets 4 The use of corrosion inhibiting coolants is always recommended for any liquid cooling system STEP 1 GENERAL INFORMATION Sample picture of GeForce GTX Titan series grakis card STEP 2 PREPARING YOUR GRAPHICS CARD ra 1 REMOVING STOCK COOLER Remove encircled screws on the be 2 3a ate m
6. sing EK PSC fittings with the EK FC Titan series water blocks To ensure that the tubes are securely attached to the barb fittings please use hose clamps or an appropriate substitute You can use any opening as an inlet outlet port Tubing ee EK PSC Fitting Water block top M3x6 DIN 7985 screw Siena PAA INSTALLING EK FC LINK Alternatively you can install the enclosed EK FC Link which allows installation of both EK FC Bridge system as well as the use of G1 4 threaded fittings Please remove the middle M4x8 DIN 7984 screw install the EK FC Link together with OR 14x1 5 mm gaskets and secure it with enclosed M4x25 DIN 7985 screw Use enclosed 2 5 mm Allen hex key Once installed you can install two preferably angled G1 4 threaded fittings or any EK FC Bridge CSQ series interconnect serial or parallel M4x25 DIN Carefully lift your graphics card with installed block and insert it in your PC s motherboard PCI express expansion slot Please bear in mind that your graphics card is probably heavier than when it was equipped with original heat sink fan assembly One needs to be very careful when handling the graphics card Avoid all unnecessary manipulation of the VGA water block assembly that might damage your card or the water block during final installation R EQUIRED TOOLS SAN N Scissors Philips and Torx T6 head screwdriver All disclosures notices and warranty conditions are being written on
Download Pdf Manuals
Related Search