Pyle PLCD5MRBTS car media receiver
Contents
1. they will go with the notches facing up into the appropriate slots at the middle left and right sides of the unit Then slide the sleeve off the back of the unit Sleeve A E L Key Co Outer Trim Ring j Front Panel R Key PEZ a 6 Mount the sleeve by inserting the sleeve into the opening of the dashboard and bend open the tabs located around the sleeve with a screwdriver Not all tabs will be able to make contact so examine which ones will be most effective Bending open the appropriate tabs behind the dashboard to secure the sleeve in place Dashboard Tabs Screwdriver E jg Sleeve 7 Reconnect the wire harness and the antenna and be careful not to pinch any wires or cables 8 Slide the unit into the sleeve until it locks into place 9 To further secure the unit use the supplied metal strap to secure the back of the unit in place Use the supplied hardware Hex Nut Mbmm and Spring Washer to attach one end of the strap to the mounting bolt on the back of the unit If necessary bend the metal strap to fit your vehicle s mounting area Then use the supplied hardware Tapping Screw 5x25mm and Plain Washer to attach the other end of metal strap to a solid metal part of the vehicle under the dashboard This strap also helps ensure proper electrical grounding of the unit Note to install the short threading terminal of the mounting bolt to the back of the unit and the other long th2. PLCD5MRBTS OWNER S MANUAL Mobile Audio System Vd IL 7 EON CLAS PLL Synthesizer Stereo Radio AM FM MPX PLL RADIO MP3 CD CD RW Compatible Automatic Memory Storing USB amp SD MMC Card Interface Fold Down Detachable Panel Auxiliary Input Function Bluetooth Hands free function amp A2DP Advanced Audio Distribution Profile Stereo Audio Transmission www pyleaudio com CONTENTS ane irre est NK 3 USB play operation 13 Take out screw before installation 3 SD MMC operation sssss 13 DIN Front Mount Method A 3 Bluetooth operatlon 15 Installing the unit 3 Preparing for operation 15 Removing the unit 4 Paing scent tae nl 15 DIN Rear Mount Method B 5 COMEC EE 15 Using the detachable front panel 6 IE 15 Wiring Connecton 7 Answering MANUANSI 16 ISO CONNECHON stood eset 7 Making an outgoing call 16 Location of KG YS aces SCR RR ERR ARA 8 Transfer the call between mobile phone Basic Operation u 9 eid TIS SUN eios iacet keen quas 16 Switching on off the unt 9 Bluetooth audio A2DP function 17 Faceplate release 9 Specification ee nee 18 Sound adjustment sssss 9 Remote Control nee 19 E iG Suse t tta sid
3. will be break off When you install the front panel you need to reconnection 4 If you turn off the mobile phone that has paired with the unit when you turn on the mobile phone you need to reconnection T MENU When successful paired shortly press T MENU button 22 on the front panel will enter the telephone menu keep pressing this button or press button 23 5 to change the items in this menu The items will be displayed in the following sequence PRE NUM RECELVED DIALED MISSED PHONE BK MANU ANS TALK The details please see the following instruction 1 RRE NUM You can save 10 phone call to the phonebook 1 In PRE NUM mode rotating button 4 to select the NUMBER Then press SEL button and enter the phone number Then press SEL button again to save it to phonebook 1 If you want to delete a number from phonebook 1 After Selected the number then press and hold BND LOU key for 2 seconds The number will be deleted 2 RECELVED Display the last call you have received memory 10 numbers 3 DIALED Display the last dialed OPERATION number memory 10 numbers 4 MISSED Display the call you have missed memory 10 numbers 5 PHONE BK You can copy 20 phone numbers from mobile to the phone book 2 of the unit via Bluetooth transmitted The way is In mobile phone enter phonebook gt more gt send via Bluetooth gt select number gt send If you want to
4. C Notes on MP3 files MP3 Version Only 1 The disc must be in the ISO9660 level 1 2 or level 2 format or Joliet or Romeo in the expansion format 3 When naming a MP3 file be sure the file name extension is MP3 4 Fora non MP3 file even though the file name extension is MP3 the unit cannot recognize it USB PLAY OPERATION In the front panel of the unit there is an USB interface 15 You can connect an USB driver through this interface 15 When you connect an USB driver through the interface the unit will search the MP3 files or WMA files in the USB driver and start to play MP3 files or WMA files automatically If in other mode you can also press MOD button 9 to select USB mode Note The main unit can only support the standard USB memory disc which is approved by Microsoft e USB MP3 player is not a standard which means different brand name or different models have their own standard So our product cannot support every MP3 player When connecting an MP3 player and there has normal battery in the player non rechargeable battery you should remove the battery from the MP3 player then connect it to the USB interface Otherwise it may cause battery burst SD MMC OPERATION OPTIONAL According to the customer s need the unit will add a SD MMC interface See below the SD MMC interface is on the housing of the unit When you insert a SD MMC card in the SD MNC interface the un
5. RESET button 25 must be activated with either a ballpoint pen or thin metal object The RESET button is to be activated for the following reasons Initial installation of the unit when all wiring is completed All the function buttons do not operate Error symbol on the display Note if press RESET button 25 the unit cant work yet please use a cotton swab soaked in isopropyl alcohol to clean the socket on the front panel MODE SELECTION Shortly press MODE button 1 to change the mode among Radio USB CARD IPOD optional AUX and BT Audio SYSTEM SETTING Press and hold SEL button 4 on the front panel to enter SYSTEM SETTING mode There are below items to adjust BEEP P VOL AREA HOUR 24H Use SEL button 4 to select the item you want to change and use SEL button 4 to change the corresponding setting 1 BEEP ON OFF Beep on There is a beep sound when buttons is pressed Beep off There is no beep sound when buttons is pressed 2 P VOL P VOL The max volume value when you turn onthe unit Such as when you set OPERATION the P VOL to 40 If the volume value is small than 40 when you turn off the unit Next time you turn on the unit The volume will keep the last volume value But if the volume value is large than 40 when you turn off the unit Then next time you turn on the unit The volume value will back to 40 3 Area Europe USA Use SEL button 4 to set the radio frequency to Eu
6. the unit might not give its optimum performance j 30 Avoid installing the unit where it would be subject to high temperature such as from direct sunlight or from hot air from the heater or where it would be subject to dust dirt or excessive vibration DIN FRONT REAR MOUNT This unit can be properly installed either from Front conventional DIN Front mount or Rear DIN Rear mount installation utilizing threaded screw holes at the sides of the unit chassis For details refer to the following illustrated installation methods TAKE OUT SCREW BEFORE INSTALLATION Before install the unit please remove the two screws Take out screw before installation J DIN FRONT MOUNT Method A Installation Opening This unit can be installed in any dashboard having an opening as shown below f 53mm 182mm Eg Installing the unit Be sure you test all connections first and then follow these steps to install the unit 1 Make sure the ignition is turned off and then disconnect the cable from the vehicle battery s negative terminal 2 Disconnect the wire harness and the antenna 3 Press the release button on the front panel and remove the control panel see the steps of removing the front panel 4 Liftthe top of the outer trim ring then pull it out to remove it 5 The two supplied keys release tabs inside the units sleeve so you can remove it Insert the keys as far as INSTALLATION
7. Current Drain RADIO Frequency Coverage IF Sensitivity S N 30dB Stereo Separation Frequency Coverage IF Sensitivity S N 20dB DC 12 Volts Negative Ground 178 W x 107 D x 50 H 10 dB 10 dB 4x60watts 15 Ampere max For 2 Bands FM 87 5 a 108 Mhz 10 7MHz 4uV gt 25dBu AM 520to 1710kHz 450kHz 38dBu REMOTE CONTROL HANDSET OPTIONAL 9 TN d d eo Se L4 amp C 3 9 FUNCTION KEY amp CONTROL NS J 1 POWER Power ON OFF Button 2 DSP 0 Display Button _ 0 For MP3 WMA Operation 3 SEL Sound Mode Select Button Character Shift Right For MP3 WMA Operation 4 VOL Volume Up Button Character Select A B 8 9 0 For MP3 WMA Operation 5 VOL Volume Down Button Character Select A B 8 9 0 For MP3 WMA Operation 6 BND LOU ENT Band Select Button When pressed shortly Loudness Button When pressed long Enter Button For MP3 WMA Operation 7 MODE 7 Mode Button S T U 7 For MP3 WMA Operation 8 TUNE SKIP CHi lt 8 Tune SKIP Down Button V W X 8 For MPS3 WMA Operation 9 TUNE SKIP CH I 9 Tune SKIP Up Button Y Z SPACE 9 For MP3 WMA Operation 10 AS PS D AUD Automatic Memory Storing amp Program Scanning Button Mode Select Button For MP3 WMA Operation 11 M1 M6 Preset Buttons A R 1 6 For MP3 WMA Operation 12 PAU Pause Button A B C 1 For MP3 WMA Operation 13 SCN Scanning Button D E F 2 For MP3 WMA
8. buttons 4 to list all songs A Notes on discs under this directory and select the title 1 Attempting to use non standard shape Ries BND LOU or SEL button to discs e g square start and heart may COH Vania s dr The pay damage the unit Be sure to use round Repeat the above steps if the newly f f selected title is again a directory shape CD discs only for this unit 2 Donotstick paper or tape etc onto the FILE label side or the recording side of any discs as it may cause a malfunction o Searching From Current Directory OPERATION 3 Dirt dust scratches and warping discs will cause misoperation B Notes on CD Rs recordable CDs CD RWSs rewritable CDs 1 Be sure to use discs with following marks only for the unit to play d COMPACT i le Gl JSE HISE DIGITAL AUDIO DIGITAL AUDIO 2 The unit cannot play a CD R and CD RW that is not finalized Please refer to the manual of your CD R CD RW recorder or CD R CD RW software for more information on finalization process 3 Depending on the recording status conditions of the disc and the equipment used for the recording some CD Rs CD RWs may not be played on this unit see 1 1 To have more reliable play back please see followi ng recommendations a Use CD RWs with speed 1x to 4x and write with speed 1x to 2x b Use CD Rs with speed 1x to 8x and write with speed 1x to 2x c Do not play a CD RW which has been written for more than 5 times
9. delete a number from phonebook 2 After Selected the number then press and hold BND LOU ez key for 2 seconds The number will be deleted 6 MANU ANS manual answer You can set Answer mode to manual answer MANU ANS mode or Auto Answer AUTO ANS mode In auto answer mode when a call coming the Phone Number will appear on LCD The unit will answer the call auto matically In MANU ANS mode when a call coming the Phone Number will appear on LCD you can press v button 24 to answer the call or press button 3 to reject the incoming call 7 TALK 00 20 You can setting the bluetooth volume in TALK 00 item If it is 00 When there is a call coming the main volume will set to 60 automatically If you set TALK to 20 The main volume will set to 100 automatically whena call is coming Example TALK volume MAIN volume 00 60 01 62 02 64 20 100 MAKING AN OUTGOING CALL 1 Making an outgoing call from SPEED DIAL RECEIVED LIST DIALED LIST MISSED LIST PHONE BOOK Mobile Phone and PHONE BOOK SIM Card please refer to the T MENU section 2 Making an outgoing call by inputting the phone number manually Press button 24 on the front panel CALL_ will appear on LCD Use 0 9 buttons to enter the phone number you want to dial Note shortly press button will input character press and hold it will input character Then press button 24 again will call the num
10. AIRING will appear on the LCD 3 On the mobile phone select the Bluetooth set up Please refer to the instruction manual of your mobile phone on how to operate Bluetooth 3 CARBT should appear in the list on your mobile phone please select CARBT and then input password 0000 4 When successful paired CONN OK will be displayed on LCD 5 When pairing failed PAIR END will be displayed on LCD You can press and hold PAIR button 1 to try the pairing again 6 Note During Pairing MODE key will no functional during pairing mode When pairing you can press PAIR button 1 to terminate the pairing CONNECT This unit is built in auto reconnection function Every time when you short press button 24 the unit will auto reconnect with the mobile phone note the mobile phone must have been paired with the unit before In the following conditions you can reconnect manually by pressing RECON button 25 for several seconds when reconnect is successful Conn OK will be displayed 1 If the mobile phone is out of range the connection will be lost when you come back to the unit reconnection is necessary 2 When the mobile phone is out of range from the unit and there is an incoming call when you come back to the unit and you want to transfer the audio to the unit you need to reconnection 3 When youpress button 2 to release the front panel the connection
11. BASIC OPERATION SWITCHING ON OFF THE UNIT Press button 6 to turn onthe unit When the unit is on press and hold button 6 to turn the unit off FACEPLATE RELEASE Press button 2 removable faceplate to detach the SOUND ADJUSTMENT Shortly press SEL button 4 to enter AUDIO SETTING mode use SEL button 4 to select the desired adjustment mode The adjustment mode will change in the following order VOL Bass Treble Balance Fader Exit Shortly press 4 to adjust the sound quality up or down step by step Shortly press MUTE button 6 will mute the sound press it again will resume the sound LOUDNESS Press LOUD button 3 for several seconds to switch loudness function on and LOUD will appear on the LCD for several seconds Press it for several seconds again to release this function DISPLAY Press DSP button 18 to change display mode LOCAL Press LOC button 16 to select between local and distant stations Local setting for reception of strong station and a distant setting for reception of weaker stations This function is effect during SEEK operation MONO Press MON button 21 to select mono or stereo mode You can sometimes improve reception of distant stations by selection EQUALIZATION Press EQ button 20 shortly to turn on equalization function and to select desired audio mode There are five kinds of mode as below gt CLAS POP ROCKEQ OFF RESET FUNCTION
12. HF button 9 shortly after the current song play to the end It will play the song in current category in random order and SHF will appear on the display Press it again to exit this mode Press it for 2 seconds to play all songs in the album and D SHF will appear on the display Press it again to exit this mode TUNE TRACK UP DOWN When playing a song press PP lt lt button 5 23 will play the next previous track in the current category but you can not enter to the next category When play a song more than 3 seconds Press lt lt button 23 will back to the start position When play a song less than 3 seconds press 4 button 23 will play the previous track When playing a song press and hold button gt aa 5 23 for several seconds will fast forward reverse of the playing And the display will show the playing time e g 1 20 BLUETOOTH OPERATION e PREPAIR FOR BLUETOOTH OPERATION i When use Bluetooth please make sure the mobile phone supports Bluetooth function ii For the different kind of mobile phone Bluetooth emissive power has some difference To get the best conversation quality it is commended that the distance between the mobile phone and the unit is within 3m And please don t put any metal object or any obstacle between the path of the mobile phone and the unit e PAIRING 1 In any mode press and hold PAIR MODE button 1 on the front OPERATION 2 panel P
13. Operation 14 RPT Repeat Button G H 1 3 For MP3 WMA Operation 15 SHF Shuffle Button J K L4 For MP3 WMA Operation 16 LOC S MOD Local Distant Select Button 19 TROUBLE SHOOTING Before going through the checklist check wiring connection If any of the problems persist after checklist has been made consult your nearest service dealer symptom Cause JL Sottion The car ignition switch is If the power supply is not on connected to the car accessory circuits but the engine is not moving switch the ignition key to ACC The fuse is blown Replace the fuse Temperature inside the car Cool off or until the ambient is too high temperature return to normal Condensation Leave the player off for an hour or So then try again No send Adjust volume to a desired level Wiring is not properly Check wiri ng connection connected Sound ski The installation angle is Adjust the installation angle less ledig more than 30 degree than 30 degree The operation The built in microcomputer Press the RESET button keys do not is not operating properly Front panel is not properly fix into Work due to noise its place The radio does The antenna cable is not Insert the antenna cable firmly not Work The connected radio station The signals are too weak Select a station manually automatic selection does not work No power 20
14. Program scanning Press AS PS button 19 shortly to scan preset station And the corresponding station number P1 P6 will flash on LCD SCAN Press SCAN button 17 to enter scan mode the unit will scan to higher frequency station and keep on each station for several seconds the corresponding frequency will flash 5 times on LCD STATION STORING Searched a station press preset button 1 6 for several seconds until 2 nd beeps come out current station is stored into the number button CD MP3 WMA OPERATION SWITCHING TO CD MODE If there is no CD MP3 WMA disc inserted into the driver Gently insert the CD MP3 WMA disc with the printed side uppermost into the disc compartment until you feel some resistance The disc will be drawn into the driver automatically CD MP3 WMA playback begins If a CD MP3 WMA disc is already inserted in the driver Keep pressing MODE button 1 shortly SELECTING TRACKS Press 5 23 will skip to the OPERATION previous next file File number will be showed on display Press and hold PP lt lt 5 23 will fast reverse forward File play starts when you release the button PAUSING PLAYING Press PAU button 10 to pause and Pause will appear on LCD Press it again to resume play PREVIEWING ALL TRACKS Press SCN button 11 to play first several seconds of each file and SCN will appear on LCD Press again to stop scan and listen to file SCN will disappea
15. ber Note if you input the wrong number shortly press CLR button will clear it Press and hold CLR button will clear all numeric TRANSFER THE CALL BETWEEN MOBILE PHONE AND THE UNIT During the talking mode you can press and hold TRANSFER T MENU button 22 to transfer the phone call between the mobile phone and the unit Note 1 If you transfer the call to mobile OPERATION phone the mute of the present mode will be released at the same time 2 When making an outgoing call it s not possible to transfer if the call is not being answered yet BT reset In BT AUDIO mode Press and hold BND LOU e key for several seconds Some of the bluetooth information and phone numbers will be lost BLUETOOTH AUDIO A2DP FUNCITON The unit supports Bluetooth audio function If your mobile phone can play stereo audio when the paring is ok you can choose the unit you have paired to play the stereo music M1 M2 button on the front panel of the unit serves as PAUSE PLAY and STOP control button It is up to the mobile phone the different mobile phone has the different define Use lt lt gt gt button 23 5 on the front panel of the unit to choose the previous next track It is up to the mobile phone the different mobile phone has the different define SPECIFICATION GENERAL Power Supply Require ments Chassis Dimensions Tone Controls Bass at 100 Hz Treble at 10 kHz Maximum Output Power
16. e ast ias d 9 Trouble shooting en 20 Displayen tiaa Sete a pcan eee ee 9 Egqu lizato E 9 Reset TUneliohus sire 9 Mode selection tte petes 9 System setting ue 9 Auxiliary InP EE 9 Radio operation ssssss 10 Selecting the frequency band 10 ofer EE 10 Station storing sss 10 CD MP3 WMA operation 10 Switching to CD mode 10 Selecting tracks usine netus 10 Pausing playing ssss 10 Previewing all tracks 11 Repeating the same track 11 Playing all tracks in random 11 Ejecting A UIS oim toi ie 11 DISC E 12 INSTALLATION Notes Choose the mounting location where the unit will not interfere with the normal driving function of the driver Before finally installing the unit connect the wiring temporarily and make sure it is all connected up properly and the unit and the system work properly Use only the parts included with the unit to ensure proper installation The use of unauthorized parts can cause malfunctions Consult with your nearest dealer if installation requires the drilling of holes or other modifications of the vehicle Install the unit where it does not get in the driver s way and cannot injure the passenger if there is a sudden stop like an emergency stop If installation angel exceeds 30 from horizontal
17. gh temperatures or direct sunlight in anywhere 6 Keep away any volatile agents e g benzene thinner or insecticides from touching the surface of the front panel 7 Do notattempt to disassemble the front panel WIRING CONNECTION ISO CONNECTION Pan B Antenna Socket L ch WHITE LINE OUT R ch RED 4 SPEAKER SYSTEM GREEN BLACK 8 Rear Left Speaker amp e GREEN 7_ o o WHITE BLACK 6 Front Le Eront Lettie o WHITE 5 D 5 o GRAY BLACK 4 Front Righ Speaker Ko GRAY 3 o VOLET BLACK 2 Rear Right Speaker e Ground Wire Black 12VAccessory Switch Red PowerAntenna AmplifierTum On Blue Memory12 Volt Constant Power Yellow VIOLET 4 OPERATION LOCATION OF KEYS 8X9 00 GMD 039 D OOOO 7 7 TM 1 MODE PAIR 2 release button 3 hang up LOU BND 4 VOL SEL MENU Audio knob 5 kb e O MUTE 7 LCD 8 4 SHF 9 5 DIR 10 1PAU 11 2 SCN 12 3 RPT 13 AUX IN 14 6 DIR 15 USB interface 16 9 LOC 17 SCAN 18 0 DSP 19 AS PS 20 8 EQ 21 7 MON 22 T MENU TRANS 23 44 24 pick up 25 Reset button 26 SD MMC interface 27 Mic 28 eject button 29 disc slot 30 IR OPERATION
18. it will search the MP3 files or WMA files in the card and start to play MP3 files or WMA files automatically The operationis the same with the MP3 operation described above If in other mode you can also press MOD button 1 to elect OPERATION SD MMC mode CAUTION When there are important files in the USB device or SD card Do not connect it to the cmain unit to play Because any wrong operation may cause files loss And our company assumes no responsibility for this IPOD operation Select Category When IPOD is playing Press BAND button 3 the category will appear on the display Rotating the volume knob 4 to change the category among PLAY LIST ARTIST ALBUM GENRE SONG COMPOSER then press SEL button 4 to confirm the selected category Select Song Press BAND button 3 the display will show the current catalog Rotating the volume knob 4 to change the song title to the next song or the previous song Then press SEL button 4 to play the selected song PAU Pause When playing a song press button 10 will pause the playing Press it again will resume playing RPT Repeat When playing a song press RPT button 12 shortly will repeat the current song and S RPT will appear on the display Press it again to exit this mode Press it for about 2 seconds to repeat Album and D RPT will appear on the display Press it again to exit this mode SHF Shuffle When playing a song press S
19. not used for method B installation USING THE DETACHABLE FRONT PANEL To Detach the Front Panel 1 Press the release button then the front panel will be folded down OPEN 2 To remove the front panel lift it up at a little angle from horizontal position then first pull out the right side and then pull out the left side The left side The right side Front Panel 3 For safekeeping store the front panel in the supplied protective case immediately after being removed Protective Case Front Panel To Install the Front Panel 1 To install the front panel first insert the left side into proper position then insert the right side into place The left side The right side Front Panel 2 When the two sides fixed into place push the front panel into main unit 3 Note that if the front panel fails to lock in position properly pressing control button may not function and the display may be missing some segments Press the release button and then reinstall the front panel again Precautions when handling 1 Donot drop the front panel 2 Do not put pressure on the display or control buttons when detaching or re installing the front panel 3 Donottouch the contacts on the front panel or on the main unit body It may result in poor electrical contact 4 Ifany dirt or foreign substances adhered on the contacts they can be removed with a clean and dry cloth 5 Donot expose the front panel to hi
20. r Press and hold SCN button 11 will play first several seconds of each file in the current folder and D SCN will appear press it again will exit this mode REPEATING THE SAME TRACK Press RPT button 12 to continuously repeat the same file and S RPT will appear on LCD Press it again to stop repeat and S RPT will disappear Press and hold RPT button 12 will repeat al the files in the current folder And D RPT will appear on LCD Press it again will exit this mode PLAYING ALL TRACKS IN RANDOM Press SHF button 8 to play all files in random order and S SHF will appear on LCD Press again to cancel the function and S SHF will disappear Press and hold SHF button 8 for 2 seconds will play all files in the current folder in random order And D SHF will appear on LCD Press it again will exit this mode EJECTING A DISC Press amp button 28 to stop CD MP3 WMA playing and eject the disc from the disc slot 29 ESP FUNCTION OPTIONAL The unit can be shockproof about 70 seconds around for MP3 WMA SELECTING DIRECTORY UP DOWN Press DIR button 9 or DIR button 14 to select directory downward or upward If the USB driver does not contain any directory there is no function of pressing DIR button 9 or DIR button 14 SELECTING TRACKS o Searching Track Directly Press AS PS SCH button 19 for one time It enters into Searching track directly mode The unit searches
21. reading terminal to the dashboard Spring Washer Hex Nut Plain Washer Tapping Screw 10 Reconnect the cable to the vehicle battery s negative terminal Then replace the outer trim ring and install the unit s front panel see the steps of installing the front panel Removing the unit 1 Make sure the ignition is turned off then disconnect the cable from the vehicle battery s negative terminal 2 Remove the metal strap attached the back of the unit if attached 3 Press the release button to remove the front panel INSTALLATION 4 Lift the top of the outer trim ring then pull it out to remove it 5 Insert both of the supplied keys into the slots at the middle left and right sides of the unit then pull the unit out of the dashboard DIN REAR MOUNT Method B If your vehicle is a Nissan Toyota follow these mounting instructions Use the screw holes marked T Toyota N Nissan located on both sides of the unit to fasten the unit to the factory radio mounting brackets supplied with your vehicle Side View showing Gr Screw Holes marked TN Screw Factory Radio Mounting Bracket Screw i D i Dashboard or Console To fasten the unit to the factory radio mounting brackets Align the screw holes on the bracket with the screw holes on the unit and then tighten the screws 5x5mm on each side Note the outer trim ring sleeve and the metal strap are
22. rope frequency or USA frequency 4 HOUR 24 12 You can select time format to 12 hour or 24 hour format In AREA item When you change the radio frequency to the EUR The time format will be changed to 24 HOUR format automatically When you change the radio frequency to the USA The time format will be change to 12 HOUR format automatically AUXILIARY INPUT The unit can be connected to a portable audio player through the AUX IN jack 13 on the front panel After finishing the connection you can press MODE button 1 to switch the mode to AUX IN mode RADIO OPERATION SELECTING THE FREQUENC Y BAND At radio mode press BAND button 3 shortly to select the desired band The reception band will change in the following order e SELECTING STATION Shortly press gt P lt lt buttons 5 23 to activate automatic seek function Press for several seconds until MANUAL appears on the display the manual tuning mode is selected If both buttons have not been pressed for several seconds they will return to seek tuning mode and AUTO appears on the display AUTOMATIC MEMORY STORING amp PROGRAM SCANNING Automatic memory storing Press AS PS button 19 for several seconds SEARCH will appear on LCD the radio will search from the current frequency and checks the signal strength until one cycle search is finished And then 6 strongest stations are stored into the corresponding preset number button
23. the track selected by following direct numeric buttons M1 M6 7 VON 8 EQ 9 LOC 0 DSP Maybe you can rotating the button 4 to select the numbers If selected three digits the unit searches the tract at once If selected one or two digits the unit wait for BND LOU or SEL button for seconds The unit searches the track after few seconds even if the enter button is not pressed o Searching Directory or File Name Press AS PS SCH button 19 for two times It enters into Searching Directory or File Name mode The unit searches files and directories that have the same character which is inputted by the user pressing the corresponding buttons listed on the below M3 GH 1 3 M N O 5 Directory s bows ep P Q R 6 Directory UP MOD S T U 7 TUNE SEEK TRACK DOWN ae OPERATION Press AS PS SCH button for four times The unit searches file or directory from current directory by button 4 The currently playing file name is displayed User can select the file by button 4 After selected a file Pressing BND LOU or SEL button to play If you would like to listen to a song which is in different directory Pleases select and press TUNE SEEK TRACK Y Z SPACE 9 CHARACTER SHIFT RIGHT _ 0 CHARACTER SELECT A B 8 9 0 _ PUSH SEL DSP AUDIO KNOB Explain as follows Use the corresponding buttons Or you can using button 4 to select the characters A to Z blank 0
24. to 9 _ SEL button Then you can select desired directory and press SEL button to enter it After selected a song then press BND LOU or SEL button to play Press SEL button 4 to confirm entry of each characters Press BND LOU button 3 to start the title search In case the selected title is a directory name display will show DISPLAY ID3 INFORMATION Press DSP button 18 to show the ID3 TAG title artist and aloum SUPPORT MP3 WMA DECODING MODE n thee He ter aue M HL SUDO MESMA MA en use the buttons 4 to list a e songs under this directory and select AS Doi the title Press BND LOU or SEL button to confirm and start the play Repeat the above steps if the newly selected title is again a directory Bit Rate Supports MPEG1 Audio 32 48 64 96 Stereo 128 192 256 320 64 96 128 192 Layer 3 44 1kHz Windows Media Audio 44 1kHz The USB solution can support Folder 500 max o Searching From Root Directory Press AS PS SCH button 19 for three times The unit searches file or directory from root by button 4 Display will list all available directories and songs Select the desired directory songs by using buttons 4 and EO eae BND LOU or SEL button to confirm H Ge Pepti o Older p layers gus 4 Size 2 GB the selected title is a song it starts to play If the selected title is a directory name display will show C then DISC NOTES Use the
Download Pdf Manuals
Related Search