Optoma WHD200 AV receiver
Contents
1. 2 3 4 Note Plug the IR blaster cable into the IR OUT jack of the transmitter Please try to manually move the IR blaster in the front of the front panel of your HD device and then press the key of remote control to search a good position of IR response Paste the IR blaster head near the front of IR sensor of your High Definition audio video devices When the IR blaster cable is connected it relays infrared command from your remote control to the device Users can control their AV devices by pointing their remote control to the receiver instead of to their AV equipment If the receiver will be out of the direct line of sight of your remote controls plug the IR Sensor Extender cable into the IR IN jack of the receiver and place the IR sensor on the front of TV for operation 1 The IR sensor supports 36KHz 56KHz NEC RC5 RC6 remote s signal protocol Therefore it is possible that some devices may not be supported 2 The IR blaster supports 47KHz remote signal protocol 15 Step 4 Boot up the Transmitter and Receiver 1 2 3 4 Place the two AAA batteries into the remote control After the power cord is plugged into the electrical outlet the WHD200 will be turned on automatically O mis S IR OUT DCIN HDMIIN HDMIIN HDMI OUT If it is in Standby mode Both POWER LED of transmitter and receiver are lit in red press POWER button either transmitter or2. Ensure that the consumer timing of your HD device is compliant with the standard listed below Primary CEA Video Timing 640x480p 59 94 60Hz 720x480p 8 59 94Hz 480p 720x480p 60Hz 720 576 9 50Hz 576p 1280x720p 50Hz 720p 1280x720p 59 94 60Hz 1920x1080i 50Hz 1080i 1920x1080i 59 94 60Hz 1920x1080p 50Hz 1080p 60 1920x1080p 59 94 60Hz Y Secondary CEA Video Timing YES YES YES YES YES YES YES YES YES ES 1920x1080p 23 98 24Hz 1920x1080p 25Hz 1080p 24 1920x1080p 29 97 30Hz VESA Timing DVI only 540x480 59 94 728099 XGA 800x600 60 317 72 188Hz SVGA 1024x768 60 70 069Hz X 1280x768 60H 1280x1024 60 Hz 1600x1200 6 YES YES YES YES YES ES 24 Mandatory CEA Video Format Timings 1280x720p 50Hz Top and Bottom 1280x720p 50Hz Frame packing 1280x720p 59 94 60Hz Top and Bottom 1280x720p 59 94 60Hz Frame packing 1920x1080i 50Hz Side by Side Half 1920x1080i 9 59 94 60Hz Side by Side Half 1920x1080p 23 98 24Hz Top and Bottom 1920x1080p 23 98 24Hz Frame packing 25 6 Audio Bit Rate Support B Digital Audio from HDMI inputs Up to 6Mbit s bit rate support B Support AC3 and DTS B 2 channel PCM 16724 bits audio sample with 32 796KHz sampling rate as below 26 7 Product Specification General Specifications Supported Video P HDMI Input 1080p 1080i 720p 576p 480p Suppo Me
3. conditions for satisfying RF exposure compliance Outdoor operations in the 5150 5250MHz 5600 5650MHz band are prohibited e This device has no Ad hoc capability for 5250 5350MHz and 5470 5725MHz e Outdoor operations in the 54707 5725MHz band are prohibited This device could not be used in the 5600 5650MHz The device not operation in 5600 5650MHz A CAUTION Using this System in Canada Industry Canada regulatory information Operation is subject to the following two conditions 1 This device may not cause interference This device must accept interference including interference that may cause undesired operation of the device The user is cautioned that this device should be used only as specified within this manual to meet RF exposure requirements Use of this device in a manner inconsistent with this manual could lead to excessive RF exposure conditions N Europe EU Declaration of Conformity This device complies with the essential requirements of the R amp TTE Directive 1999 5 EC The following test methods have been applied in order to prove presumption of conformity with the essential requirements of the R amp TTE Directive 1999 5 EC e EN 60065 2002 A1 2006 A11 2008 A2 2010 e Safety of Information Technology Equipment e EN50371 2002 Generic standard to demonstrate the compliance of low power electronic and electrical apparatus with the basic restrictions related to human
4. country s safety rules However there is no guarantee that interference will not occur in some installation scenario If the interference happens increase the distance between the transmitter and receiver WHD200 may interfere 5GHz wireless devices such as routers or other wireless devices Therefore if you have an 802 11n router configure it to the 2 4 GHz band rather than the 5GHz band Optimal range between WHD200 transmitter and receiver is between 2 and 20 meters within line of sight A CAUTION of RF module on US region Any changes or modifications not expressly approved by the grantee of this device could void the user s authority to operate the equipment This equipment must be installed and operated in accordance with provided instructions and the antenna s used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co located or operating in conjunction with any other antenna or transmitter End users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance Outdoor operations in the 5150 5250MHz 5600 5650MHz band are prohibited This device has no Ad hoc capability for 5250 5350MHz and 5470 5725MHz Outdoor operations in the 5470 5725MHz band are prohibited This device could not be used in the 56007 5650MHz The Device not operation in 5600 5650MH
5. exposure to electromagnetic fields 10 MHz 300 GHz General public e EN 301 893 V1 5 1 2008 Broadband Radio Access Networks BRAN 5 GHz high performance RLAN Harmonized EN covering essential requirements of article 3 2 of the R amp TTE Directive e EN 301 489 1 V1 8 1 2008 Electromagnetic compatibility and Radio Spectrum Matters ERM ElectroMagnetic Compatibility EMC standard for radio equipment and services Part 1 Common technical requirements e EN 301 489 17 V2 1 1 2009 Electromagnetic compatibility and Radio spectrum Matters ERM ElectroMagnetic Compatibility EMC standard for radio equipment and services Part 17 Specific conditions for 2 4 GHz wideband transmission systems and 5 GHz high performance RLAN equipment Hereby Zinwell declares that this Full HD Video wireless kit is in compliance with the essential requirements and other relevant provisions of Directive 1995 5 EC A Industry Canada Statement This device complies with RSS 210 of the Industry Canada Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation IMPORTANT NOTE IC 9078A ZRF31200 Radiation Exposure Statement This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment This equipment should be installed and opera
6. feet minimum 9 On Screen Display OSD vs RCU Instruction On Active mode Press the POWER button on the top of Receiver or press Power button point to receiver receiver enter Standby mode and transmitter s HDMI out is on OSD Displayed Display 3secs and then enter Standby mode fo T On Active mode Press the POWER button on the top of Transmitter or press RCU Power button point to transmitter both transmitter and receiver will enter Standby mode OSD Displayed Display 3secs and then enter Standby mode fol i T OFF O Press the INFO button on the RCU and Signal Quality Source Channel and resolution will be displayed for user reference OSD Displayed Press again for exit a SM HDMI1 CH10 1280x1024 Log 19 Press the SOURCE button on the RCU or on the top of transmitter or receiver for audio video source input selection OSD Displayed Kol 4 CH10 1280x1024 or Hoi ss 4 S HDMI2 CH10 1280x1024 O Press the IR button of RCU for change IR Blaster frequency enable to switch IR Blaster frequency 47K to 56K to 36K recurring Note IR blaster frequency default setting is 47KHz Press once for current IR frequency status display The OSD shows 2 4 SM HDMI1 CH10 1280x1024 If Press IR key again to switch IR blaster frequency The OSD shows m 4 HDMI1 CH10 1280 1024 If 4 NOTE Onl
7. for equipment with rated current 16 A per phase and not subject to conditional connection EN 55024 Information technology equipment Equipment Immunity characteristics Limits and methods of measurement EN 301 489 1 Electromagnetic compatibility and Radio spectrum Matters ERM Electro Magnetic Compatibility EMC standard for radio equipment and services Part 1 Common technical requirements EN 301 489 17 Electromagnetic compatibility and Radio spectrum Matters ERM Electro magnetic Compatibility EMC standard for radio equipment Part 17 Specific conditions for 2 4 GHz wideband transmission systems 5GHz high performance RLAN equipment and 5 8 GHz Broadband Transmitting Systems EN 60065 Audio gt video and similar electronic apparatus Safety requirements TRADEMARK INFORMATION e HDMI the HDMI Logo and High Definition Multimedia Interface are trademarks of HDMI Licensing LLC Special Notice Never use this product nearby an aircraft or medical facility It can cause interference or undesirable effect on the operation result Use of this product in the following locations may result in abnormal video and audio output noise blocked image etc Product installed in the walls made of concrete Product is situated near the refrigerator or metal fitment A cluttered room where the wireless signals may be blocked This product has been tested and manufactured to comply with each
8. ina residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help A CAUTION Using the System in the US e Any changes or modifications not expressly approved by the grantee of this device could void the user s authority to operate the equipment e This equipment must be installed and operated in accordance with provided instructions and the antenna s used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co located or operating in conjunction with any other antenna or transmitter End users and installers must be provide with antenna installation instructions and transmitter operating
9. tablies pour un environnement non contr l Cet quipement doit tre install et utilis avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps i les dispositifs fonctionnant dans la bande 5 150 5 250 MHz sont r serv s uniquement pour une utilisation l int rieur afin de r duire les risques de brouillage pr judiciable aux syst mes de satellites mobiles utilisant les m mes canaux ii De plus les utilisateurs devraient aussi tre avis s que les utilisateurs de radars de haute puissance sont d sign s utilisateurs principaux c d qu ils ont la priorit pour les bandes 5 250 5 350 MHz et 5 650 5 850 MHz et que ces radars pourraient causer du brouillage et ou des dommages aux dispositifs LAN EL NOTE IMPORTANTE Dans le cas o ces conditions ne peuvent tre satisfaites par exemple pour certaines configurations d ordinateur portable ou de certaines co localisation avec un autre metteur l autorisation du Canada n est plus consid r comme valide et l ID IC ne peut pas tre utilis sur le produit final Dans ces circonstances l int grateur OEM sera charg de r valuer le produit final y compris l metteur et l obtention d une autorisation distincte au Canada 2 Introduction WHD200 is a Full HD wireless transmission device This solution delivers uncompressed 1080p full HD video and audio content to your existing HDTV set wirelessly It operates the t
10. the ventilation slots on the receiver transmitter or place any heavy object on the top cover Blocking the air flow could damage the receiver Arrange components so that air can flow freely around the receiver Ensure that there is adequate ventilation if the receiver is placed in a stand Put the receiver transmitter in a property ventilated area away from direct sunlight or any source of heat e Water Exposure To reduce the risk of fire or electric shock do not expose the receiver transmitter to rain or moisture e This is indoor solution e Our company has the right to modify this document without any notice DECLARATION OF CONFORMITY This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesired operation EMI Electro Magnetic Interference tested EN 55022 Information technology equipment Radio disturbance characteristics Limits and methods of measurement EN 61000 3 2 Electromagnetic compatibility EMC Part 3 2 Limits Limits for harmonic current emissions equipment input current up to and including 16 A per phase EN 61000 3 3 Electromagnetic compatibility Part 3 Limits Section 3 Limitation of voltage changes voltage fluctuations and flicker in public low voltage supply systems
11. HDMI OUT Z i ee we i 1 Connect the transmitter s HDMI IN to the High Definition AV sources HDMI OUT through by HDMI cable The transmitter has two HDMI inputs for the High Definition source device like PS3 Blu ray Player 2 Connect the transmitter s HDMI OUT to the HDTV set s HDMI IN port with an HDMI cable for the loop through connection 3 Connect the supplied power adapter to the DC IN jack of the transmitter and a wall socket The LED indicator in the POWER button lights up in blue when the WHD200T is connected to the power mains 13 Step2 Setup WHD20OR receiver HDTV set Connection with WHD200R High Def Projector High Def Flat panel TV 1 Connect the HDMI cable to the HDMI OUT jack of the receiver and to your HDTV set or an HD projector Press the Source Input button of your TV s remote to select the appropriate HDMI video input 2 Connect the supplied power adapter to the DC IN jack of the receiver and a wall socket The POWER LED indicator lights up in blue when the receiver is connected to the power mains Step3 Setup the IR blaster extender cable and IR sensor extender cable If necessary connect the Infrared IR blaster or sensor Extender cable Users can point hand held remote control of your High Definition AV equipment at the receiver or the HDTV set to operate the source devices not exceeding the distance of 66 feet at Line of sight 1
12. If is Searching system can t establish Blinking deal available Blinking Ulo link over 80s after Blue Looping display channels initialization these two OSD Note A amp D No input from selected Blinking source Static Blue Quickly Note B linked Video format not Wireless Blinking Mode recognized Static Blue Slowly Note C Video format is Static Blue Static Blue recognized 18 Note A Ifthe RF connection over 80sec and still not established it might link lost or the transmitter is most likely out of range You may have to verify the range and adjust or shorten the distance between your HDTV set with the transmitter and the receiver The maximum video transmission range for 1080p content is up to 66 feet in line of sight LOS lt The minimum range is 6 5 feet gt B Please make sure the computer have been power on and switched the signal output to HDMI out also try to re plug the HDMI cable to make sure the HDMI connector had settled well C If there is no video displayed and OSD displayed Not Supported Format this is an indication that the video frame rate from the computer is not supported please refer chapter 5 to switch a supported video timing D If you have more than one pair of WHD200 each transmitter and receiver should be at least 6 5 feet away from one another If both the transmitter and the receiver exist in the same room the suggested the distance between the two is 6 5
13. User s Manual Full HD VideoWireless Kit WHD200 Transmitter WHD200 Receiver Please read the user manual and the quick installation guide so you can enjoy the product to the full extend Table of Contents TABLE OF CONTENU S iN ER nn Neve AAA 1 1 IMPORTANT INFORMATION 0000000000000000000000000000000000000000000000000000000000000000000000000000000000000000 2 SAFETY PR CAUTIONS esie RE hee eu oe athe DL aR ne 2 DANGER BE CAREFUL WITH ELECTRICITY eene here rer sesto sse sees 2 2 INTRODUCTION 00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000 8 2 1 PAGKING CONTENT e eee cues eee Eo mince NE EYE NEN VER ani CERE VE ERR Fee SE e NN cei ove eT EE es 8 2 2 OVERVIEW d c ie este do 8 2 2 OVERVIEW H 8 2 2 1 WHD200T TX PC TO TV TRANSMITTER ccsccesccesccesccsccesccnsccnsccesccesccsccesccesccescees 10 2 2 2 WHD200R RX PC TO TV RECEIVER usant 10 2 2 2 WHD200R RX PC TO TV RECEIVER eee senenn annan 11 2 2 3 REMOTE CONTROLLER UNIT INSTRUCTION ccccsccsscccscccsccesscesccecccsccesccsccescees 12 S INSTALLATION oes idee gone eO a E Eae Y evo NANE aee e Te ive Cou ces 13 STEP1 SETUP THE WHD200T TRANSMITTER ccccccccccccccccccccccccccccccccccccccccccccccccccc
14. ayed t on your TV screen OSD displayed Hk Ensure your video resolution and frame rate is recognized supported and within the transmission range Connect the source device to your TV to check and modify the video format compatibility Check if your video resolution with HDMI input from your device is set among 1080p 1080i 720p 576p or 480p Please refer Chapter 5 for the detail supported Resolution POWER LED in Solid Blue STATUS LED Flash Quickly dod a OSD displayed 4 gt Ensure the proper cables are connected between the transmitter and 22 Poor picture quality or intermittent video No audio IR Blaster can t control Source device No 3D video output your AV source devices Ensure your source devices connected to the WHD200 transmitter are powered on Ensure the proper cables are connected between the receiver and your 274 HDTV near the receiver Check if your video resolution with HDMI input from your device is either 1080p 1080i 720p 576p or 480p Please refer to the Supported Resolution chapter where the video frame rate from your HD AV device WHD200 can support is defined Ensure the transmission distance is less than 66 feet LOS e Check your TV s volume is properly set and not set in MUTE mode e Check if your source player s audio volume has been turned up Ensure the bit rate of audio from the source device can be supported by WHD200 Please refer to the detail
15. cccccccccecs 13 STEP2 SETUP THE WHD20OOR RECEIVER ccccccccccccccccccccccccccccccccccccccccccccccccccccccccccccscccccees 14 STEP3 SETUP THE IR BLASTER EXTENDER CABLE AND IR SENSOR EXTENDER CABLE 15 STEP 4 BOOT UP THE TRANSMITTER AND RECEIVER ccccccccccccccccccccccccccccccccccccccccccccccccccccccecs 16 STEP 5 MOUNTING THE WHD200 TO THE WALL ccccccecccccccccccccccccccccccccccccccccccccccccecs 21 A TROUBLESHOOTING OA SEENA ENEE a Aaa 21 5 SUPPORTED RESOLUTION iirc UNES e a R E EU CE VEN So vax a 24 6 AUDIO BIT RATE SUPPORT es mimi NN CEN ee v Ce goassa ag die encens eee 26 7 PRODUCT SPECIFICATION an en nl ils tenes Se eek 27 1 Important Information Please take the time to read this user manual before using the WHD200T and WHD200R It contains important information about operating your Full HD video wireless kit Our limited warranty applies when the product is handled properly for intended use in accordance with its operating instruction However the warranty may be void in the following cases Repair product modification or alteration have been performed by unauthorized service personnel Damages caused by accidents including but not limited to lightning water fire or moisture Use of an AC adapter not compatible with the product and its voltage rating The model number on the product has been altered deleted removed or made illegib
16. e HER Digital Audio Up to 6 Mbps AC3 and DTS Formats The maximum video transmission range is 20 meters 66 feet Transmission Distance The minimum range is 2 meters Line of sight LOS scenarios System Latency No latency 1ms High Performance Internal Antennas Operating Frequencies 4 9 5 9GHz Include non DFS and DFS Frequency Bands Power Supply 100 240V AC in 5V 2A DC out Power Adaptor Operating Temperature _ 0740 C Interfaces WHD200T WHD200R AN HDMI Input TWO Type A ER Interfaces HDMI Output One Type A One Type A Signal IR Blaster Extender 2 5mm Jack a ke Interfaces IR Sensor Extender IR Sensor IR Sensor Extender FONET Power Input 5V DC Jack 5V mini USB Interface Power LED 1 x LED Two Tone Blue Red 1 x LED Two Tone Blue Red 1 Quality Status OSD Displayed 27
17. le Safety Precautions RISK OF ELECTRICAL SHOCK DO NOT OPEN WARMING TO REDUCE THE RISK OF ELECTRICAL SHOCK DO NOT REMOVE THE COVER NO USER SERVICEABLE PARTS ARE INSIDE REFER SERVICING TO QUALIFIED PERSONNEL A Danger Be careful with electricity Power to the units must be switched off before any work is undertaken such as any AV device connection or TV connection Power outlet To prevent electric shock make sure to use the appropriate AC adapters as power supply to the transmitter and the receiver Power cord Be sure the power cord is routed so that it will not be stepped on or pinched by heavy items Power overloading Avoid overloading electrical outlets or extension cords which otherwise could result in electric shock or fire Lightning Disconnect the product from the power source if it is left unattended for a long period of time and to protect the product from lightning e Always disconnect the power cord from the power outlet when you are not using your Full HD Video wireless kit This reduces the risk of electric shocks or fire A Warning e This product should not be exposed to dripping or splashing No object filled with liquids such as vases should be placed on the product e Object Entry To avoid electric shock never stick anything in the slots on the case or remove the cover e Place receiver transmitter on a flat hard and stable surface Ventilation Do not block
18. ransmission in 4 9 GHz 5 9 GHz frequencies and it can adjust its communication frequency automatically in case of interference from another RF system With built in Omni directional antennas it can transmit uncompressed video content to 20 meters 66 feet LOS Line of sight with no latency Both IR Sensor Extender Cable and IR Blaster Extender Cable are included in the package so users can point their remote control of the AV source at the receiver directly for device operation 2 1 Packing Content Please check whether the following items are present in the package If any items missed or damaged please call your dealer mE Quick Install Guide Quick Installation IR Blaster cable HDMI cable DC Power Adapter Mini USB Power A 7 2 2 Overview 2 2 1 WHD200T TX PC to TV Transmitter M Front Panel Buttons and LEDs Source Selection Button Press to switch Source inputs of the transmitter Power Button with LED Indicator Press to turn the transmitter on and off The indicator in the power button is lit in solid blue when the power is on and turns red in standby mode 6 Source LEDs These two LED indicators are lit in solid blue to show current input you switch Main Unit Back Panel IR OUT Blaster Extender Jack Plug the IR Blaster Extender Cable into the IR OUT jack of HDMI OUT Connect Transmitter to High definition audio video devices that ha
19. receiver to turn on the transmitter and the receiver Same condition for remote control operation gt If transmitter s HDMI out display is on Transmitter POWER LED is lit in purple and receiver stay in Standby mode Receiver POWER LED is lit in red press the POWER button of receiver or transmitter to wake up system and will make wireless connection automatically between transmitter and the receiver 16 5 6 7 During the warm up the POWER LED will blink in blue until the signal link between the WHD200T and the WHD200R is established It will take 15 20 seconds for system boot up successfiillv pees ums Ensure your TV set or projector is in HDMI input mode and is already powered on High Def Flat panel TV Press the Source button on the RCU or on the top of receiver transmitter for Source input switch until you see the video being broadcasted from your device WIDE CHANNEL 17 8 If all operation is normal the POWER LED and INFO CHANNEL LED will glow in solid blue Please refer to the below form containing detailed LED indicator and OSD description of transmitter receiver Power LED Status LED OSD Display Status Description on RX on RX on RX Standby For power saving mode Static Red Initial Boot It will spend 15 20 Blinking up Warm seconds for system boot Blinking Blue up up Continuing search Wedl mu available channels
20. s in Chapter 6 Audio Bit Rate Support Check where is IR sensor of Source device Make sure IR Blaster sensor is close and straight to Source device s IR sensor Please refer Chapter 3 step 3 for reference setup Change IR Blaster frequency to meet Source device s requirement See the page 20 for the IR blaster frequency switch OSD displayed TX 35 or and RX 35 Check both of TVs include Tx and Rx side should support 3D video format Either one of TV only support 2D format then 3D output might not supported f user wants to display 3D video on HDTV which supported 3D video please turn off 2D HDTV and RE power on 3D HDTV Then set the source player to 3D video format output for the 3D display Check the video output setting of Source player ex Blu ray Disc PS3 etc If the video output setting of Source player is 3D video format It might be abnormal display on HDTV which not supports 3D format 3D video format do not support on current equipments status If user wants to display 3D video on HDTV which supported 3D video please turn off 2D HDTV and RE power on 3D HDTV Then set the source player to 3D video format output for the 3D display 23 5 Supported Resolution If the SOURCE LED continues to blink in blue slower than no signal mode OSD display o and there is no video displayed or the video quality suffers it indicates that the video frame rate from your A V source device is not supported
21. ted with minimum distance 20cm between the radiator amp your body Caution i the device for operation in the band 5150 5250 MHz is only for indoor use to reduce the potential for harmful interference to co channel mobile satellite systems ii high power radars are allocated as primary users i e priority users of the bands 5250 5350 MHz and 5650 5850 MHz and that these radars could cause interference and or damage to LE LAN devices IMPORTANT NOTE In the event that these conditions can not be met for example certain laptop configurations or co location with another transmitter then the Canada authorization is no longer considered valid and the IC ID can not be used on the final product In these circumstances the OEM integrator will be responsible for re evaluating the end product including the transmitter and obtaining a separate Canada authorization French translation Ce dispositif est conforme la norme CNR 210 d Industrie Canada applicable aux appareils radio exempts de licence Son fonctionnement est sujet aux deux conditions suivantes 1 le dispositif ne doit pas produire de brouillage pr judiciable et 2 ce dispositif doit accepter tout brouillage recu y compris un brouillage susceptible de provoquer un fonctionnement ind sirable NOTE IMPORTANTE IC 9078A ZRF31200 D claration d exposition aux radiations Cet quipement est conforme aux limites d exposition aux rayonnements IC
22. ve an HDMI port using a provided HDMI cable HDMI OUT Connect to HDTV set via an HDMI cable DC IN For connecting the SWW1810T power adapter 10 2 2 2 WHD200R RX PC to TV Receiver M Front Panel Buttons and LEDs Power Button with LED indicator Press to turn the receiver on and off The indicator in the power button lights up in blue when the power is on and turns red in standby mode Source LEDs For HDMI1 and HDMI2 selected indication Source Button Press this button for Source input selection M Main Unit Back Panel DC IN HDMI OUT Connect to receiver s Connect to HDTV set via an HDMI cable power adapter 2 2 3 Remote Controller Unit RCU Instruction POWER Button Press to turn the Transmitter amp Receiver on off When both of TX amp RX Power LEDs are red press Power button either TX OR RX it can wake up each other automatically OINFO Button Press this button to display OSD for system related information on HDTV connected on receiver O SOURCE Button Press to switch the audio video sources input connected to transmitter directly OIR Button Press to switch the IR Blaster frequency to meet Source device s requirement It can switch IR Blaster frequency 47K to 56K to 36K recurring 12 3 Installation Step1 Setup the WHD200T transmitter Connect Two High Definition Audio Video Sources to the transmitter O IR OUT DCIN HDMIIN HDMIIN
23. y the status of the WHD200R receiver connected to the HDTV can be displayed on the OSD The status of the WHD20OT transmitter HDMI out cannot be displayed 20 Step 5 Mounting the WHD200 to the Wall 1 Refer the drawing of the bottom page that have relative position of the main holes and attach this paper on wall 2 Drill pilot holes 3 Insert the supplied two Anchors into the wall 2 4 Insert two screws into the anchors Leave 1 8 length for mounting the Transmitter or receiver 5 6 Place WHD200 main holes over the protruding screws and slide down into position 21 4 Troubleshooting problem sohtiom The WHD200 power indicator LED doesn t light up e Check if the power plugs of WHD200T WHD200R are properly inserted into a functioning power outlet e Verify that the proper cables have been selected and installed between the WHD200T transmitter input and your High Definition device output e On your TV side connected to the WHD200R select the HDMI as input source e Verify the POWER LED and SOURCE LED indicator of WHD200 Power LED Flashing in Blue 050 displayed S 4 levels looping Ensure the transmission range between the transmitter and the receiver is NOT over 66 feet LOS line of sight transmission distance Try to move the transmitter closer to the receiver POWER LED in Solid Blue Slow and Flashing SOURCE LED No video is displ
24. z Industry Canada regulatory information Operation is subject to the following two conditions 1 this device may not cause interference and 2 this device must accept any interference including interference that may cause undesired operation of the device The user is cautioned that this device should be used only as specified within this manual to meet RF exposure requirements Use of this device in a manner inconsistent with this manual could lead to excessive RF exposure conditions The following statement must be included with all versions of this document supplied to an OEM or integrator but should not be distributed to the end user gt This device is intended for OEM integrators only gt Please See the full Grant of Equipment document for other restrictions gt This device must be operated and used with a locally approved access point e The following regulatory and Safety notices must be published in documentation supplied to the end user of the product or system incorporating an adapter in compliance with local regulations Host system must be labeled with Contains FCC ID XXX XXXXX FCC ID displayed on label System Warning FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference
Download Pdf Manuals
Related Search