Digitus DS-51200
Contents
1. USB KVM EXTENDER OVER CAT 5 User s Manual DS 52100 1 INTRODUCTION feu 1 1 gy ict 3 1 2 PACKAGE CONTENTS ptem tenia ee beast a 3 1 3 SPECIFICATIONS Suh dac bte unt ote bo i ee da bte bo teams 4 ZEE Gp URB que m 2 1 SYS TEM REQUIREMENT Sirsa ete te D eldest atu iet 5 2 2 SIS AL yal asa gel Mile 6 2 3 HARDWARE INSTALLATION 8 3 OPERATIONS ree MM 3 1 ACTIVE CONSOLE SELECTION BY PUSH 9 3 2 TINBIG ATORS D D EPA ILE 9 3 3 BUZZER SOUND DISABLE ENABLE BY HOTKEY n edd te eo eon doles ds 11 3 4 SUN MICRO SYSTEM FUNCTION KEY EMULATION enne 12 Introduction Thank you for purchasing the USB KVM Extender over Cat 5 This KVM extender allows you to extend the computer s video and USB keyboard mouse signal Therefore you now have a high quality and durability extension solution to control your system up to 200 meters away from your computer or KVM With the built in video and keyboard mouse signal enhancement you can gain the best video resolution quality Additional software is not required This product delivers perfect performance and high value to satisfy your needs The USB KVM Extender over Cat 5 comprises a local2. 1600 x 1200 100 m 1400x 900 150m 1280x1024 60HZ 200m es Windows 98SE ME 2000 XP 2003 Server Vista 7 Linux Mac OS9 OSX and Sun Microsystems DC 5V 2A Adaptor 127 x 67 x 27 mm 246 g Extension Cable amp Length Video Resolution lt Firmware Upgrade Operating Systems Supported Power Supply Dimension Lx W xH Unit Weight 243 g mr D Housing material T Operating Temperature 122 F 0 50 C 0 80 RH I 3 o 1 K 1 2 Installation 2 1 System Requirements Console 1 SVGA Multisync monitor capable of the highest resolution 2 USB keyboard mouse Computer 1 VGA SVGA or multisync card 2 AUSB port or PS 2 6 pin mini DIN for keyboard and mouse 3 Operating systems Windows 98 98SE 2000 ME XP 2003 Vista 7 Mac OS9 OSX Linux Kernel 2 3 or later Solaris 8 or later Sun Micro OS Cables 1 CATS CATSE CATS6 cable to connect the remote and local unit the supported maximum length of this cable is 200 meters 2 Custom combo 4 in 1 cable accessories 2 2 Physical Diagram E Transmitter Front View Reset switch LED indicators Push button USB keyboard USB mouse Rear View Cat5 Video to local monitor Video KB MS to PC Power jack AUN Receiver Front View Reset switch LED indicators USB keyboard USB mouse Video adjusted skews
3. AOUN Rear View 5 Upgrade Video to local monitor Power jack BONA B Reset Switch Press the Reset switch if you want to reset the system This switch must be pushed with a thin object like the end of a paper clip or a ball point pen B Firmware download connector The min USB female connector on the rear of the KVM switch is for a firmware upgrade function To update your KVM firmware please contact your dealer B Cable Connection Diagram Transmitter Receiver 1 Monitor 2 PC 3 Video KB MS 4 USB mouse 5 USB keyboard 2 3 Hardware Installation 1 Switch off all devices 2 Connect your monitor USB keyboard mouse to the local unit if you want to control your system at the local console 3 Connect your monitor USB keyboard mouse to the remote unit if you want to control your system at the remote console 4 Connect the remote and local unit by using a CAT5 CAT5E CAT6 cable the supported maximum cable length is 200 meters 5 Connect the 5V power supply to power on the local unit 6 Connect the 5V power supply to power on the remote unit Connect video and or USB keyboard mouse of local unit and computer KVM by using the supplied cables 8 Turn on your computer if it was turned off 9 Adjust video quality by using brightness or focus skew if necessary 3 Operations 3 1 3 2 Active Console Selection by Push Button You can press the push button on the local unit to change the act
4. cator Indicates whether the connection between the local and remote unit is ready or not Examples of LED Indicators Both consoles are selected local active is ON remote active is OFF It means that the connection between the local unit and the computer is ready but the CAT5 connection between the local and remote unit is not ready In this case you can only control your system at the local console because the remote console is not connected successfully The following indicators are shown at the local console all LED indicators will be OFF at the remote console because of disconnection Remote Local Selected la la Active E 10 B Both consoles are selected local active is OFF remote active is ON It means that the CAT5 connection between the local and remote unit is ready but the local unit is not connected to the PC correctly or the PC is not turned on In this case you cannot control your system from any console because the PC is not available to control Remote Local Selected la active W B Both consoles are selected local active is ON remote active is ON Connection of the local and remote unit is successful you can control your system at the local and the remote console Remote Local Selected la la Active la E B Active console is inconsistent with selected console You cannot control your system if the active console is inconsistent with the selected Remote Local Re
5. ealer or an experienced radio TV technician for help 13
6. icrosystems 13 Supports BIOS level operation 14 Plug and Play 15 Supports Microsoft Intellimouse 3 5 key mouse amp Microsoft Natural Keyboard Pro series 16 Supports SUNMICRO system function key emulation 17 LEDs on each device to indicate the active console and connection status 18 Firmware upgradeable Package Contents The product you purchased should contain the equipment and accessories shown as follows 1 1x Local Unit 2 1 Remote Unit 3 1 Custom combo 4 in 1 cable 4 2x External power adaptor DC 5V 2A 5 1 x User s Manual 1 3 Specifications mum Output HDB 15 Female HDB 15 Female Keyboard A Female 058 A Fema Connectors USB Keyboard USB Type A Female USB Type A Female USB Type A Female USB Type A Female HDB 15 Female PC Connectors Video KB MS PS 2 amp USB signal N A combined Extension Port RJ 45 FOR KB MS VGA Extension Video Adjustment Q o 2 gt 2 3 gt gt lt lt lt A A Brightness Selected Right Red LED Right Green LED Left Red LED Left Green LED Right Red LED Right Green LED Left Red LED Left Green LED Active LED indicator Selected Active 2 3 amp rm lt Local Remote Switch Button DDC Supported es REMOTE Support DDC2B CAT5 6 Max Length 200M 1920 x 1200 50m
7. it or any other commercial damage including but not limited to special incidental consequential or other damages No part of this document may be reproduced or transmitted in any form by any means electronic or mechanical including photocopying recording or information recording and retrieval systems without the express written permission of the manufacturer All brand names and product names used in this document are trademarks or registered trademarks of their respective holders FCC Statement This device generates and uses radio frequency and may cause interference to radio and television reception if not installed and used properly This has been tested and found to comply with the limits of a Class B computing device in accordance with the specifications in Part 15 of the FCC Rules These specifications are designed to provide reasonable protection against such interference in a residential installation However there is no guarantee that interference will not occur in a particular installation If this device does cause harmful interference to radio or television reception which can be determined by plugging the device in and out the user can try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the device and receiver Connect the computer into an outlet on a circuit different from that to which the receiver is connected Consult the d
8. ive console of operation There are three types of active console configurations 1 Local Console Only You can operate the system only from the local unit 2 Remote Console Only You can operate the system only from the remote unit 3 Both Consoles You can operate the system from both the local and remote unit The default configuration is Both Consoles mode Once you change the active console configuration it will be saved and will not be affected by unit reset The active console can be shown via Selected Indicators of LED indicator please refer the description of next sections LED Indicators The LED indicators of the remote console are the same as the local ones if both units are connected successfully or all LED indicators at remote console will turn OFF Selected Indicators RED B Both Selected Indicates that you can control your system from both the local and remote console Remote Local Selected Active E Local Selected Indicates that you can control your system from the local console only Remote Local Selected la Active E Remote Selected Indicates that you can control your system from the remote console only Remote Local Selected la Active E Active Indicators GREEN Indicates the connection status Local Indicator Indicates whether the connection between the local unit and computer is ready or not Remote Indi
9. mote Local Selected Sa Selected Y xu e d 3 3 Buzzer sound Disable Enable by Hotkey WB X Press Left Shift or Right Shift twice then B and Enter The buzzer sound will be disabled enabled alternately The buzzer sound default setting is ON lt Shift gt Shift gt B Enter 11 3 4 Sun Micro System Function Key Emulation There are 16 special functions on the Sun Micro system keyboard the KVM Switch can emulate these function keys Here is the mapping table for Sun Micro function key emulation To activate this emulation you have to press the LEFT Window KEY first this key usually is located between the left Ctrl and left Alt then choice the second relative key Sun Micro System Function Key Stop Props Compose Front Open Find Again Undo Copy Paste Cut Help Power Mute Volume Down Volume UP 9 Emulation Key L Win amp L Alt L Win amp L Ctrl L Win amp L Shift L Win amp F1 L Win amp F2 L Win amp F3 L Win amp F4 L Win amp F5 L Win amp F6 L Win amp F7 L Win amp F8 L Win amp F11 L Win amp F12 L Win amp 1 L Win amp 2 L Win amp 3 Disclaimer Information in this document is subject to change without notice The manufacturer does not make any representations or warranties implied or otherwise regarding the accuracy and completeness of this document and shall in no event be liable for any loss of prof
10. unit transmitter and a remote unit receiver The local unit is connected directly to the computer or a KVM switch system using the supplied cables The user console keyboard mouse and monitor is attached to the remote unit The remote and local units extend the keyboard mouse and video signal along the Cat5 5e 6 cable Moreover the local unit offers dual access enabling the connection of a second user console close to the computer Local Unit Transmitter Remote Unit Receiver 1 1 1 2 Features Extends the Keyboard Video Mouse signal by a Cat5 5e 6 cable Dual console operation Control your system from both the local and remote unit Push button at local side to select active console Available active console options local console remote console both consoles 1 2 3 4 5 Supports connection of USB keyboard mouse for local and remote console arbitrarily 6 Supports keyboard mouse connection of USB interface to computer at local side arbitrarily 7 Supports high resolution video Up to 1280x1024 60Hz for distances of up to 200 meters 8 Supports SVGA and multisync monitors 9 DDC2B support for remote monitor 10 Adjustable control of focus and brightness to improve video quality at remote side 11 No software or driver installation required 12 Compatible with most commonly used operating systems like DOS Windows 98SE ME 2000 XP 2003 Server Vista 7 Linux Mac OS9 OSX and Sun M
Download Pdf Manuals
Related Search