Moxa EDS-G205A-4PoE-1GSFP
Contents
1. O 10 mounting kit 15 DIN Rail mounting kit H pu Hee E e Rear View 14 O 15 1 Mounting Dimensions un 135 9 DIN Rail Mounting The aluminum DIN Rail attachme t mm J 5 105 _ 113 8 nt plate should already be fixed to the back panel of the EDS when you take it out of the box If you need to reattach the DIN Rail attachment plate make sure the stiff metal spring is situated towards the top as shown in the figures below STEP 1 Insert the top of the DIN Rail into the slot just below the stiff metal spring STEP 2 The DIN Rail attachment unit will snap into place as shown below Metal Spring DIN Rail Metal Spring DIN Rail To remove the EDS from the DIN Rail simply reverse Steps 1 and 2 above Wall Mounting optional For some applications you will find it convenient to mount the EDS G205A 4PoE on the wall as shown in the following figures STEP 1 Remove the a8 aluminum DIN Rail R attachment plate from the Q G EDS G205A 4PoE s rear Sa panel and then attach the wall mount plates as shown in the diagram at the right oe g O o oO 8 4 STEP 2 Mounting the EDS G205A 4PoE on the wall requires 4 screws Use the switch with wall mount plates attached as a guid2. use a small Top View flat blade screwdriver to tighten the wire clamp screws on the Sg front of the terminal block connector STEP 3 Insert the plastic terminal block connector prongs into the terminal block receptor which is located on EDS s top panel Front View A ATTENTION Before connecting the EtherDevice Switch to the DC power inputs make sure the DC power source voltage is stable Communication Connections The EDS P205A 4PoE switches have 4 10 100 1000Base T X PoE Ethernet ports for connecting PoE devices and 1 10 100 1000Base T port or 1 1000Base X SFP slot for uplink connection 10 100 1000Base T X Ethernet Port Connection 10 100 1000Base T X ports located on the EDS s front panel are used to connect to Ethernet enabled devices Below we show pinouts for both MDI NIC type ports and MDI X HUB Switch type ports and also show cable wiring diagrams for straight through and cross over Ethernet cables 10 100Base T X Pinouts MDI Port MDI X Port 8 pin RJ45 Pinouts Pinouts Pin Signal Pin Signal 1 TX 1 RX 2 TX 2 RX 3 RX 3 TX 4 RX 4 TX 1000Base T Pinouts MDI Port MDI X Port 8 pin RJ45 Pinouts Pinouts Pin Signal Pin Signal 1 BI_DA 1 BI_DB 2 BI_DA 2 BI_DB 3 BI_DB 3 BI_DA 4 BI_DC 4 BI_DD 5 BI_DC 5 BI_DD 6 BI_DB 6 BI_DA 7 BI_DD 7 BI_DC 8 BI_DD 8 BI_DC PoE Ethernet Port Connec
3. attention to the following points e Use separate paths to route wiring for power and devices If power wiring and device wiring paths must cross make sure the wires are perpendicular at the intersection point NOTE Do not run signal or communications wiring and power wiring in the same wire conduit To avoid interference wires with different signal characteristics should be routed separately e You can use the type of signal transmitted through a wire to determine which wires should be kept separate The rule of thumb is that wiring that shares similar electrical characteristics can be bundled together e Keep input wiring and output wiring separated e It is strongly advised that you label wiring to all devices in the system when necessary Grounding the EtherDevice Switch Grounding and wire routing help limit the effects of noise due to electromagnetic interference EMI Run the ground connection from the ground screw to the grounding surface prior to connecting devices A ATTENTION This product is intended to be mounted to a well grounded mounting surface such as a metal panel Wiring the Redundant Power Inputs The two 2 contact terminal block connectors on the EDS s top panel are used for the EDS s two DC power inputs Top and front views of the terminal block connectors are shown here STEP 1 Insert the negative positive DC wires into the V V op terminals STEP 2 To keep the DC wires from pulling loose
4. pins 1 2 3 6 choose a cross over Ethernet cable to connect the PD and the EDS switch If the PD only supports PoE MDI X mode V V V V for pins 1 2 3 6 choose a straight through Ethernet cable between the PD and the EDS switch Redundant Power Inputs Both power inputs can be connected simultaneously to live DC power sources If one power source fails the other live source acts as a backup and automatically supplies all of the EDS s power needs DIP Switch Settings The default setting for each DIP Switch is aaem m OFF The following table explains the effect of setting the DIP Switches to the ON BSP positions ON OFF DIP Switch Setting Description Serves no function reserved for future use BSP ON Enables broadcast storm protection OFF Disables broadcast storm protection ATTENTION To actively update DIP switch settings power off and then power on the EDS LED Indicators The front panel of the EDS switches contain several LED indicators The function of each LED is described in the following table LED Color State Description Pi AMBER On Power is being supplied to power input Pi Off Power is not being supplied to power input P1 P2 AMBER On Power is being supplied to power input P2 Off Power is not being supplied to power input P2 10 100 1000 AMBER On TP port s 10 100 Mbps link is ac
5. C 60068 2 27 Freefall IEC 60068 2 32 Vibration IEC 60068 2 6 WARRANTY Time Period 5 years Details www moxa com warranty Technical Support Contact Information Wwww moxa com support Moxa Americas Toll free 1 888 669 2872 Tel 1 714 528 6777 Fax 1 714 528 6778 Moxa Asia Pacific Tel 886 2 8919 1230 Fax 886 2 8919 1231 Moxa Europe Tel 49 89 3 70 03 99 0 Fax 49 89 3 70 03 99 99 Moxa China Beijing office Tel 86 10 6872 3959 60 61 Fax 86 10 6872 3958 13
6. EDS G205A 4PoE Hardware Installation Guide Moxa EtherDevice Switch First Edition October 2011 MOXA 2011 Moxa Inc All rights reserved P N 1802002051020 Overview The EDS G205A 4PoE series industrial Ethernet switches are rugged entry level industrial 5 port gigabit PoE switches that support IEEE 802 3 IEEE 802 3u IEEE 802 3x with 10 100 1000M full half duplex MDI MDIX auto sensing and IEEE 802 3af IEEE 802 3at PoE standards The EDS G205A 4PoE series provides 24 48 VDC redundant power inputs that can be connected simultaneously to a live DC power source The switches are available with a standard operating temperature range from 0 to 60 C or with a wide operating temperature range from 40 to 75 C and their IP30 metal housing makes them rugged enough for any harsh industrial environment To provide greater versatility for use with applications from different industries the EDS G205A 4PoE switches also allow users to enable or disable broadcast storm protection with DIP switches on the outer panel The EDS G205A 4PoE switches can be easily installed on a DIN Rail or in distribution boxes The DIN Rail mounting capability and IP30 metal housing with LED indicators make the plug and play EDS G205A 4Po0E switches reliable and easy to use NOTE Throughout this Hardware Installation Guide we use EDS as an abbreviation for Moxa EtherDevice Switch EDS Moxa EtherDevice Switch Package Checklist Your EDS is shi
7. e to mark the correct locations of the 4 screws The heads of the screws should be less than 6 0 mm in diameter and the shafts should be less than 3 5 mm in diameter as shown in the figure at the right NOTE Before tightening the screws into the wall make sure the screw head and shank size are suitable by inserting the screw into one of the keyhole shaped apertures of the wall mounting plates Do not screw the screws in completely leave about 2 mm to allow room for sliding the wall mount panel between the wall and the screws STEP 3 Once the screws are fixed on the wall insert the four screw heads through the large parts of the keyhole shaped apertures and then slide the EDS downwards as indicated Tighten the four screws for added stability 8 Wiring Requirements A WARNING Safety First Turn the power off before disconnecting modules or wires The correct power supply voltage is listed on the product label Check the voltage of your power source to make sure that you are using the correct voltage Do NOT use a voltage greater than what is specified on the product label Calculate the maximum possible current in each power wire and common wire Observe all electrical codes dictating the maximum current allowable for each wire size If the current goes above the maximum ratings the wiring could overheat causing serious damage to your equipment You should also pay
8. on is not required at installation or during maintenance The half full duplex mode for the switched RJ45 ports is user dependent and changes by auto negotiation to full or half duplex depending on which transmission speed is supported by the attached device Jumbo Frame By default EDS G205A 4PoE series supports Ethernet jumbo frame up to 9 6K which is with more than 1500 bytes of payload This is commonly used for large packet size applications such as video surveillance Broadcast Storm Protection The EDS G205A 4PoE Series has built in algorithm for limiting the amount of broadcast packets through the switch This function is by default enabled and can be disabled by turning off the DIP switch labeled BSP on the top cover If the broadcast storm protection algorithm detects more than 2k broadcast frames per second then the switch will be suppressed from receiving broadcast frames for a period of 2ms to prevent any further flooding 11 Specifications Technology Standards IEEE 802 3 for 10BaseT IEEE 802 3u for 100BaseT X and 100BaseFX IEEE 802 3ab for 1000Base T IEEE 802 3z for 1000Base X IEEE 802 3x for Flow Control IEEE 802 3af for PoE IEEE 802 3at for PoE Processing Type Store and Forward Interface RJ45 Ports 10 100 1000Base T X auto negotiation speed F H duplex mode and auto MDI MDI X connection Fiber Ports 1000 Base X ports SFP Slot LED Indicators Power P1 P2 TP P
9. ort 10 100 1000 Fiber Port 1000 PoE Ports PoE for Port 2 3 4 5 DIP Switch enable disable broadcast storm protection Power Input Voltage 24 48 VDC Input Current 6 83 3 28 A with full PoE loading Connection Removable 4 contact terminal block Overload Current 12A Protection Reverse Polarity Present Protection Conformance to UL Always use an isolated power supply to standards conform to the UL 508 standard Note We strongly recommend using an isolated power supply with maximum output current of 7 5 A due to the power de rating issue of the power supply at high operating temperatures Moreover without galvanic isolation between the redundant power inputs of this device the Vi and V2 should use the same voltage Physical Characteristics Housing Aluminum IP30 protection Dimensions 29 W x 135 H x 105 L Weight 300g Installation DIN Rail Mounting Wall Mounting with optional kit Environmental Limits Operating Standard models 0 to 60 C 32 to 140 F Temperature Wide temp models 40 to 75 C 40 to 167 F Storage Temperature 40 to 85 C 40 to 185 F Ambient Relative 5 to 95 non condensing Humidity Regulatory Approvals EMI FCC Part 15 CISPR EN55022 class A EMS EN61000 4 2 ESD Level 3 EN61000 4 3 RS Level 3 EN61000 4 4 EFT Level 3 12 EN61000 4 5 Surge Level 3 EN61000 4 6 CS Level 3 EN61000 4 8 Shock IE
10. pped with the following items If any of these items is missing or damaged please contact your customer service representative for assistance e Moxa EtherDevice Switch e Hardware Installation Guide e Moxa Product Warranty booklet Features High watt Power over Ethernet e Up to 30 watts output per PoE port IEEE 802 3at e Short circuit and over current protection e Auto detection for IEEE 802 3af and IEEE 802 3at High Performance Network Switching Technology e 10 100Base T X 1000Base T and 1000Base X SFP e 10 100 1000M Full Half Duplex MDI MDIX auto sensing e IEEE 802 3 802 3u 802 3x e Store and Forward switching process type 8K MAC address entries e 9 6K jumbo frame Rugged Design e Redundant dual 24 48 VDC power inputs e Operating temperature range from 0 to 60 C or extended operating temperature of 40 to 75 C for T models e IP30 metal housing e DIN rail or panel mounting ability EDS G205A 4PoE Standard Panel Layouts Front View EDS G205A 4PoE 1GSFP EDS G205A 4PoE m Terminal blocks for P1 P2 power inputs Power input P1 LED Power input P2 LED PoE status LED 10 100 1000Base T X PoE ports port 2 3 4 5 6 TP port speed LED 7 10 100 1000Base T X port port 1 8 10 100 1000Base X SFP slot 9 Model name 10 Grounding screw 11 Pi power input terminal block 12 P2 power input terminal block 13 DIP switches f 14 Screw holes for panel TRON
11. tion PoE ports located on the EDS switch s front panel are used to connect to PoE enabled devices The pinout follows the Alternative A MDI mode of 802 3af 802 3at standards Please see the details in the following table PoE Port Pinout Pin Power 8 pin RJ45 1 V 2 V 3 V 6 V NOTE According to IEEE 802 3af at standards the PD shall be implemented to be insensitive to the polarity of the power supply and shall be able to operate per MDI mode and MDI X mode However some PDs only support MDI mode or MDI X mode only The following figure shows how to select the correct cable between the PD and EDS G205A 4POE RJ45 8 pin to RJ45 8 pin Cable Wiring RJ45 8 pin to RJ45 8 pin Straight Through Cable Wiring Straight Through Cable Switch Port NIC Port RJ45 Plug Pin 1 RJ45 RJ45 Connector Cable Wiring Connector Tx 3 3 Rx Tx 6 6 Rx Rx 1 1 Tx Rx 2 2 Tx DD 4 4 DC DD 5 5 DC DC 7 T DD DC 8 8 DD RJ45 8 pin to RJ45 8 pin Cross Over Cable Wiring Switch Port Cross Over Cable Switch Port NIC Port IE NIC Port RJ45 Plug Pin 1 RJ45 RJ45 Connector Cable Wiring Connector Rx Tx 3 1 Rx Tx Rx Tx 6 2 Rx Tx Tx Rx 1 3 Tx Rx Tx Rx 2 6 Tx Rx DD DC 4 T DD DC DD DC 5 8 DD DC DC DD 7 4 DC DD DC DD 8 5 DC DD e NOTE If the PD only supports PoE MDI mode V V V V for
12. tive Blinking Data is being transmitted at 10 100 Mbps Off TP Port s 10 100 Mbps link is inactive GREEN On TP port s 1000 Mbps link is active Blinking Data is being transmitted at 1000 Mbps Off TP Port s 1000 Mbps link is inactive 1000 GREEN On SFP module s 1000Mbps link is active Blinking Data is being transmitted at 1000 Mbps Off SFP module s 1000Mbps link is inactive PoE AMBER On The PoE device is connected by IEEE 802 3af standard Off No PoE power output or no PoE connected PoE devices Green On The PoE device is connected by IEEE 802 3at standard Off No PoE power output or no PoE connected PoE devices Red Blinking PoE failure 1 time s PoE standard detection failure 2 times s PoE current overload Off No PoE failure 10 Auto MDI MDI X Connection The Auto MDI MDI X function allows users to connect the EDS s 10 100 1000Base T X ports to any kind of Ethernet device without needing to pay attention to the type of Ethernet cable being used for the connection This means that you can use either a straight through cable or cross over cable to connect the EDS to Ethernet devices Triple Speed Functionality and Switching The Moxa EtherDevice Switch s 10 100 1000 Mbps switched RJ45 port auto negotiates with the connected device for the fastest data transmission rate supported by both devices All models of Moxa EtherDevice Switch are plug and play devices so that software configurati
Download Pdf Manuals
Related Search