Panasonic SC-HTB770
Contents
1. Use this button to turn the active subwoofer on and off m The active subwoofer is on gd The active subwoofer is off The active subwoofer will still consume a small amount of power even when it is turned off W amp B Check that the wireless link is activated WIRELESS LINK Se WIRELESS LINK indicator Lights red The wireless link is not activated Lights green The wireless link is activated Blinks green The active subwoofer is trying to activate the wireless link with the main unit LL The wireless link will be activated when the main unit and the active subwoofer are both turned on Bluetooth connection By using the Bluetooth connection you can listen to the sound from the Bluetooth audio device from this system wirelessly Preparation Turn on the Bluetooth feature of the device and place the device near the main unit Bluetooth pairing EP Press Q to select Q o Ifthe yy indicator flashes quickly go to step 3 Press and hold until the g indicator flashes quickly e Ifthe yy indicator flashes slowly repeat step 2 Select SC HTB770 from the Bluetooth device s Bluetooth menu e f prompted for the passkey on the Bluetooth device enter 0000 e Once the Bluetooth device is connected the H indicator stops flashing and lights up Connecting a Bluetooth device EP Press to select Q o Ifth2. Green Red Insert the wire fully Right speaker connector White Center speaker connector Blue line Left speaker connector Insert the wire fully taking care not to insert beyond the wire insulation Press into the groove x If you have difficulty inserting the cable try straightening the speaker cable and then bending the cable about 20 mm 32 from the tip at an angle of approx 45 as illustrated above 83 Drive a screw into the wall e Use the measurements indicated below to identify the screwing positions on the wall e Leave at least 20 mm 32 of space above and on each side of the speaker to allow enough space for fitting the speaker e Keep the screws out of reach of children to prevent swallowing Atleast 30 mm 1 3 16 24 0 mm 32 7 0 mm to 9 4 mm 32 to 3 8 Wall or pillar 5 5mm to 6 5 mm 7 s2 to 1 4 S 3 O d Q O O 300 238 mm 9 7 8 745mm 29 11 2 248 mm 9 2 4 20 mm 2 32 Wall mounting hole RQT9778 1 3 4 Wall mount the speakers Fit the speaker securely onto the screw s Red connector The speaker attached to the red connector cable is to be placed on the right side White connector The speaker attached to the white connector cable is to be placed on the left side if y y b White Red DO NOT Move the speaker so In this position the t
3. Mass Weight Main unit Active subwoofer Operating temperature range 0 C to 40 C 32 F to 104 F Operating humidity range 20 to 80 RH no condensation Approx 1 15 kg 2 54 Ibs 4 76 kg 10 5 lbs Bluetooth SECTION Bluetooth system specification Version 3 0 Wireless equipment classification Class 2 Supported profiles A2DP Frequency band 2402 MHz to 2480 MHz Adaptive Frequency Hopping Operating distance 10 m 33 ft Line of Sight SPEAKER GENERAL For wall mounting layout Horizontal placement Dimensions 1230 mmx68 mmx41 mm WxHxD 48 The X2 M 16 X 1 10 16 Mass Weight 1 98 kg 4 37 Ibs Vertical placement of front speakers Front Speaker Dimensions 68 mmx541 mmx41 mm WxHxD 2 he 21 She X1 176 Mass Weight Center Speaker Dimensions WxHxD Mass Weight For table top layout Horizontal placement using the leg stands High Dimensions 1230 mmx 96 mmx68 mm WxHxD 48 The X3 12h X2 11 16 Mass Weight 2 04 kg 4 50 Ibs Horizontal placement using the leg stands Low Dimensions 1230 mmx87 mmx68 mm WxHxD 48 16 X3 The X2 11 6 Mass Weight 2 04 kg 4 50 Ibs Horizontal placement using the support legs and the speaker feet Dimensions 0 78 kg 1 72 Ibs 178 mmx70 mmx45 mm 7 X2 3 4 X1 1 16 0 37 kg 0 82 Ibs 1230 mmx71 mmx60 mm WxHxD 48 The X2 13e X2 he Mass Weight 2 kg 4 41 Ibs Vertical placement of front speakers Front Speaker
4. Center speaker connector Ali Insert the wire fully White Blue line gt Green 3 Assemble the front speakers Attach the stand neck e The two front speakers are interchangeable e Keep the screws out of reach of children to prevent swallowing Screw supplied e Tighten securely iG Assemble the front speakers Connect the speaker cables Insert the wire fully White Blue line Insert the wire fully taking care not to insert beyond the wire insulation Press into the groove x If you have difficulty inserting the cable try straightening the speaker cable and then bending the cable about 20 mm 32 from the tip at an angle of approx 45 as illustrated above 1 6 RQT9778 5 Drive a screw into the wall e Use the measurements indicated below to identify the screwing positions on the wall e Leave at least 20 mm s2 of space above and on each side of the speaker to allow enough space for fitting the speaker e Keep the screws out of reach of children to prevent swallowing Front speakers Atleast 30 mm 1 3 16 4 0 mm 32 7 0 mm to 9 4 mm 32 to 3 8 Wall or pillar 5 5 mm to 6 5 mm 32 to 1 4 Front speaker Rear view 100 mm 3 1 16 436 mm 17 32 34 mm 1 11 32 Wall mounting hole Q000 O Center speaker At least 30 mm 1 3 6 4 0 mm 32 7 0
5. and on the remote control for more than 4 sec e All the indicators will blink for 10 sec when the code of this system is changed E To turn off VIERA Link HDAVI Control When HDAVI Control compatible equipment does not work well with this system for example it is possible to turn off this function as follows e When VIERA Link is turned off the ARC function is not available Be sure to connect the optical digital audio cable gt 26 1 While pressing and holding MUTE on the remote control press and hold VOL on the main unit for more than 4 sec 2 After the setting has changed turn off all the connected devices and then turn them on again e All the indicators will blink once when VIERA Link HDAVI Control is turned off The setting is maintained until it is changed again LI e f the main unit does not operate after changing the code repeat steps 1 and 2 e To change the remote control code to code 1 repeat the steps above but replace 3 with INPUT SELECTOR E To reduce the clear mode dialog effect When the dialog does not sound natural while the volume is set low it is possible to reduce the dialog enhancing effect as follows While pressing and holding SOUND on the remote control press and hold VOL on the main unit for more than 4 sec e All the indicators will blink once when the clear mode dialog effect is reduced e Even if clear mode dialog eff
6. Bluetooth indicator blinks quickly When the main unit is ready for pairing Bluetooth indicator blinks slowly When the main unit is waiting to connect Bluetooth indicator turns on e When the main unit is connected with a Bluetooth device x2 The BD DVD indicator stops blinking and lights once the wireless pairing is successful x3 The indicator blinks only when SOUND is pressed for more than 4 sec and the audio format is PCM 40 RQT9778 EREI EIES RQT9778 41 Limited Warranty ONLY FOR U S A AND PUERTO RICO Panasonic Consumer Marketing Company of North America Division of Panasonic Corporation of North America One Panasonic Way Secaucus New Jersey 07094 Panasonic Products Limited Warranty Limited Warranty Coverage For USA and Puerto Rico Only If your product does not work properly because of a defect in materials or workmanship Panasonic Consumer Marketing Company of North America referred to as the warrantor will for the length of the period indicated on the chart below which starts with the date of original purchase warranty period at its option either a repair your product with new or refurbished parts b replace it with a new or a refurbished equivalent value product or c refund your purchase price The decision to repair replace or refund will be made by the warrantor Home Theater Audio System All included Accessories 90 Davs Not Except Non Rechargeable Bat
7. Dimensions 148 mmx 552 mmx 148 mm WxHxD 5 1348 X21 12he X5 3 16 Mass Weight Center Speaker Dimensions WxHxD Mass Weight 0 89 kg 1 96 Ibs 178 mmx71 mmx44 mm 7 X2 Bhe X1 12 16 0 37 kg 0 82 Ibs LI 1 Specifications are subject to change without notice 2 Weight and dimensions are approximate 3 Total harmonic distortion is measured by a digital spectrum analyzer RQT9778 39 v Q S g x Indicator illumination The indicators display the condition of this system by flashing The indicator patterns illustrated below are displayed during normal operational conditions They do not refer to the indications of a problem Indicator TV BD DVD AUXI AUX2 AUX3 STANDARD STADIUM CINEMA NLS OYI LN TV BD DVD AUX1 AUX2 AUX3 STANDARD STADIUM CINEMA NLS e e e e e eo e e IN TV BD DVD AUX1 AUX2 AUX3 STANDARD STADIUM CINEMA NEWS TV BD DVD AUX1 AUX2 AUX3J STANDARD STADIUM CINEMA TV BD DVD AUX1 AUX2 AUX3 STANDARD STADIUM MUSIC CINEMA NEWS Description The BD DVD indicator blinks and sound mode indicators light up in sequence for 1 minute When the main unit is in wireless pairing mode with the active subwoofer gt 37 The indicator blinks for 10 sec e When the Bluetooth communication is mode 1 gt 34 The indicator blinks for 20 sec e When 3D surround effect and clear mode dialog effect are on gt 34 e When the dual audio setting is Mai
8. Reference Troubleshooting sorsoran Eia 36 Specifications sienu a E A a aa 38 GIG ator Uiminen ET A 40 Limited Warranty ONLY FOR U S A AND PUERTO RICO aaasnnnnssnnnnnnnnnnnnnnnnnnnnnnnnnnnnrnnnrnnnnnnnnnnnnnnnnnn 42 Limited Warranty ONLY FOR CANADA cccccesseeeeeeeeeeeeeeeeneeeeseaeneeeseaeneessneeneees 43 RQT9778 5 The illustrations shown may differ from your unit e Operations in this Owner s Manual are described mainly with the remote control but you can perform the operations on the main unit if the controls are the same Supplied items I This system SC HTB770 1 Main unit 1 Active 1 Center speaker 2 Front speakers SU HTB770 subwoofer SB HTB770 SB HTB570 SB HWA770 Accessories Check the supplied accessories before using this system 1 Remote control 2 AC power supply 3 Speaker cables 1 Metal bracket with a battery cords REE1789 RED RMLO760A N2QAYC000083 K2CB2CB00022 REE1790 WHITE Length 3 m 9 8 ft REE1791 GREEN Length 2 m 6 1 2 ft 6 Screws 2 Hook brackets 2 Stand necks 2 Side caps XYN5 J14F JK RMLO763 RGK2444 RGK2445 R RGK2446 L 2 Leg stands 2 Support legs 2 Speaker bases 2 Speaker feet RGK2463 RGK2464 RGK2465 RKAX0042 k ONLY FOR CANADA The enclosed Canadian French label sheet corresponds to the English display on the remote control and the top and rear of the ma
9. The setting changes each time INPUT SELECTOR is pressed e The indicator for the selected setting blinks for 20 sec and then exits the setting mode e The setting is maintained until it is changed again 72 S S ws g RQT9778 3 3 Bluetooth communication mode You can select different modes to suit the type of connections with emphasis on connectivity or high quality audio Make sure that a Bluetooth device is already paired with this system gt 29 EP Press to select indicator will blink slowly If the indicator lights a Bluetooth device is already connected with this system Disconnect it gt 29 B Press to display the current mode STANDARD indicator blinks MODE1 Factory preset Emphasis on connectivity STEREO indicator blinks JA MODE2 Emphasis on audio quality 8 While the mode is displayed press 3 to select the mode e The setting changes each time i is pressed e The indicator for the selected setting blinks for 10 sec and then exits the setting mode The setting is maintained until it is changed again 3 4 RQT9778 Using the Dolby Virtual Speaker effect Depending on your preference It is possible to turn off the 3D surround effect and the clear mode dialog effect EP While pressing and holding SOUND on the remote control press and hold VOL on the main unit for more than 4 sec STANDARD indicat
10. an electrician for replacement of the obsolete outlet 10 Protect the power cord from being walked on or pinched particularly at plugs convenience receptacles and the point where they exit from the apparatus 11 Only use attachments accessories specified by the manufacturer 12 Use only with the cart stand tripod bracket or table specified by the manufacturer or sold with the apparatus When a cart is used use caution when moving the cart apparatus combination to avoid injury from tip over 13 Unplug this apparatus during lightning storms or when unused for long periods of time 14 Refer all servicing to qualified service personnel Servicing is required when the apparatus has been damaged in any way such as power supply cord or plug is damaged liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped NO oR WD gt 2 RQT9778 p WARNING Unit To reduce the risk of fire electric shock or product damage Do not expose this unit to rain moisture dripping or splashing Do not place objects filled with liquids such as vases on this unit Use only the recommended accessories Do not remove covers Do not repair this unit by yourself Refer servicing to qualified service personnel AC power supply cord The power plug is the disconnecting device Install this unit so tha
11. cannot be done Check the Bluetooth device condition The device cannot be connected The pairing of the device was unsuccessful or the registration has been replaced Try pairing the device again gt 29 This system might be connected to a different device Disconnect the other device and try pairing the device again The device is connected but audio cannot be heard through this system For some built in Bluetooth devices you have to set the audio output to SC HTB770 manually Read the operating instructions for the device for details The sound is interrupted The device is out of the 10 m 33 ft communication range Bring the Bluetooth device closer to the main unit e Remove any obstacle between the main unit and the device e Other devices that use the 2 4 GHz frequency band wireless router microwaves cordless phones etc are interfering Bring the Bluetooth device closer to the main unit and distance it from the other devices Select MODE1 for stable communication gt 34 Sound No sound or image Turn muting off 30 e Check the connections to the other devices gt 26 27 Make sure that the received audio signal is compatible with this system 38 e Turn this system off and then on again e f the main unit is connected to the TV with only an HDMI cable make sure that the TV s HDMI terminal is labeled HDMI ARC If not connect using the o
12. for the TV HDMI cable EJ Not labeled HDMI ARC OD _t AUDIO IN ES aio Je HDMI cable Optical digital audio cable e When you use the optical digital audio cable insert the tip correctly into the terminal 2 6 RQT9778 p Connection with other devices You can direct the audio signal from the connected Blu ray Disc player DVD player Set Top Box etc to this system When the device has an HDMI terminal Preparation e Connect the main unit to the TV gt 26 HDMI OUT CD qo ES e g Blu ray Disc player HDMI OUT e g Set top box HDMI OUT e g Video game console HDMI cable E HDMI standby pass through Even if the main unit is in standby mode the audio and or video signal from the device connected to the BD DVD AUX1 or AUX2 terminal will be sent to the TV connected to the HDMI OUT terminal the sound will not be output from this system When devices are connected to all BD DVD AUX1 and AUX2 terminals audio and or video signal of the device whose input is lastly selected is output E 3D compatibility Compatible with FULL HD 3D TV and Blu ray Disc player e The main unit can pass through the 3D video signal from a 3D compatible Blu ray Disc player to
13. mm to 9 4 mm 32 to 3 8 Wall or pillar 1 6 mm to 2 5 mm 16 to 3 32 Max 3 5 mm 64 Center speaker Rear view 18 mm 23 32 147 mm 5 29 32 13 mm 1 2 19 6 mm 29 32 50 2 mm 1 31 32 3 2 2 7 te RQT9778 1 7 6 Fit the speaker s securely onto the screw s Red connector The speaker attached to the red connector cable is to be placed on the right side White connector The speaker attached to the white connector cable is to be placed on the left side Left speaker connector DO NOT Front speaker Center speaker Front speaker Center speaker e Move the speaker so that the screw is in this position In this position the speaker will likely fall if moved to the left or right 1 8 RQT9778 When placing the speakers on a table Place the speakers using the leg stands 2 Front 1 Center speaker _ 3 Speaker cables H 2 speakers Oey WHITE Left oo a Do g Q gt RED Right GREEN Center 1 Metal i 2 Leg stands C 6 Screws bracket Os EVP EY GP e For a safety measure to prevent the speakers from falling refer to page 24 To prevent damage or scratches lay down a soft cloth and perform the assembly on it d Assemble the speakers following steps 1 and 2 of Place the speakers horizontally gt 12 13 B Attach the leg stands With the speaker facin
14. returned to the factory preset To change the remote control code refer to page 35 General operation No power Insert the AC power supply cord securely gt 28 e After turning the main unit on if the indicators blink and the main unit immediately turns off unplug the AC power supply cord and consult your dealer The remote control does not work properly The battery is depleted Replace it with a new one gt 9 It is possible that the insulation sheet has not been removed Remove the insulation sheet gt 9 t may be necessary to set the code of the remote control again after changing the battery of the remote control gt 35 Use the remote control within the correct operation range gt 9 The TV indicator blinks Remove the AC power supply cord and consult your dealer If there are any other indicators blinking be sure to inform your dealer about the blinking indicators The main unit is automatically switched to standby mode The main unit will automatically switch to standby mode when no signal is input and no operation is performed for approx 30 minutes gt 28 The main unit is turned off when the TV s speakers are selected in the speaker control This is a normal feature when using VIERA Link HDAVI Control 4 or later Please read the operating instructions for the TV for details about its power save feature 4 32 36 RQT9778 This system does not operate cor
15. system LL e VIERA Link HDAVI Control based on the control functions provided by HDMI which is an industry standard known as HDMI CEC Consumer Electronics Control is a unique function that we have developed and added As such its operation with other manufacturers equipment that supports HDMI CEC cannot be guaranteed This unit supports HDAVI Control 5 function HDAVI Control 5 is the standard for Panasonic s HDAVI Control compatible equipment This standard is compatible with Panasonic s conventional HDAVI equipment e Please refer to individual manuals for other manufacturers equipment supporting VIERA Link function 3 2 RQT9778 What you can do with VIERA Link HDAVI Control To make sure that the audio is output from this system turn the main unit on by using the TV s remote control and selecting home theater from the speaker menu of VIERA Link menu The availability and function of the settings may vary depending on the TV Refer to the operating instructions for the TV for details E Speaker control You can select whether audio output is from this system or the TV speakers by using the TV menu settings Home theater This system is active e When the main unit is in standby mode changing the TV speakers to this system in the VIERA Link menu will automatically turn the main unit on You can control the volume setting of this system using the volume or mute button on the T
16. system does not operate as expected or sound is unusual returning the settings to the factory preset may solve the problem gt 36 x The sound mode indicators blink from left to right or from right to left while adjusting The indicators will not blink when it has reached the maximum or minimum e f there is sound coming out of the TV s speakers reduce the volume of the TV to its minimum e f the main unit is turned off with the volume setting in the greater half above 50 the main unit will automatically lower the volume to the middle 50 when the main unit is turned on Volume limitation To turn this function off refer to page 35 30 RQT9778 3D sound This system provides a feeling that the sound and the image are as one To change the applied effect refer to Sound modes gt right e g Image of 3D sound field A With this effect you can enjoy a surround sound effect similar to 5 1ch Adding to the Dolby Virtual Speaker effect Panasonic has applied its own sound field controlling technology to expand the sound field forwards backwards upwards and downwards providing a sound with depth and force that better matches 3D images Sports commentary and dialogs from TV dramas are heard as if the sound is coming from the TV giving the feeling that the sound and the image are one Also the dialog will stand out from the other sounds during normal volume playback and when
17. the white connector cable is to be placed on the right side White connector Keep the screws and the speaker feet out of reach of children to prevent swallowing a FP gm Align the projecting parts on the speaker with support leg Red ot Screw supplied Right speaker connector e Tighten securely Left speaker connector Screw hole Speaker foot supplied 2 0 RQT9778 Place the front speakers using the speaker bases 2 Front 1 Center speaker 3 Speaker cables speakers OO WHITE Left ay RED Right GREEN Center 2 Stand necks 2 Speaker bases E 2 Side caps Iy lt 6 Screws 2 Speaker feet 2 e For a safety measure to prevent the speakers from falling refer to page 24 To prevent damage or scratches lay down a soft cloth and perform the assembly on it d Assemble the center speaker Attach the side caps and speaker feet to the speaker and connect the speaker cable e There is no left and right for the center speaker Insert the wire fully taking care not to insert beyond the wire insulation e Keep the screws and the speaker feet out of reach of children to prevent swallowing Getting started EY I i 9 ee Green Screw supplied Insert the wire fully e Tighten securely White Speaker foot supplied Blue line Center speaker connector Push RQT9778 2 1 B Assemble the front spea
18. to operate this device This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Responsible Party Panasonic Corporation of North America One Panasonic Way Secaucus NJ 07094 Support Contact Panasonic Consumer Marketing Company of North America Telephone No 1 800 211 PANA 7262 THE FOLLOWING APPLIES ONLY IN CANADA This device complies with RSS GEN RSS 210 of the IC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference 2 This device must accept any interference received including interference that may cause undesired operation of the device THE FOLLOWING APPLIES IN THE U S A AND CANADA This transmitter must not be co located or operated in conjunction with any other antenna or transmitter This equipment complies with FCC IC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency RF Exposure Guidelines in Supplement C to OET65 and RSS 102 of the IC radio frequency RF Exposure rules This equipment has very low levels of RF energy that is deemed to comply without maximum permissive exposure evaluation MPE But it is desirable that it should be i
19. well ventilated Do not obstruct this unit s ventilation openings with newspapers tablecloths curtains and similar items Button type battery Lithium battery e Danger of explosion if battery is incorrectly replaced Replace only with the type recommended by the manufacturer Keep out of reach of children Insert with poles aligned Mishandling of batteries can cause electrolyte leakage and may cause a fire Remove the battery if you do not intend to use the remote control for a long period of time Store ina cool dark place Do not heat or expose to flame Do not leave the battery ies in a car exposed to direct sunlight for a long period of time with doors and windows closed Do not touch the terminals and with metal objects Do not recharge disassemble remodel heat or throw into fire e When disposing the batteries please contact your local authorities or dealer and ask for the correct method of disposal CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE SCREWS NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to p
20. AIR IS NEEDED DURING THE WARRANTY PERIOD THE PURCHASER WILL BE REQUIRED TO FURNISH A SALES RECEIPT PROOF OF PURCHASE INDICATING DATE OF PURCHASE AMOUNT PAID AND PLACE OF PURCHASE CUSTOMER WILL BE CHARGED FOR THE REPAIR OF ANY UNIT RECEIVED WITHOUT SUCH PROOF OF PURCHASE Limited Warranty Limits And Exclusions This warranty ONLY COVERS failures due to defects in materials or workmanship and DOES NOT COVER normal wear and tear or cosmetic damage The warranty ALSO DOES NOT COVER damages which occurred in shipment or failures which are caused by products not supplied by the warrantor or failures which result from accidents misuse abuse neglect mishandling misapplication alteration faulty installation The model number and serial number of this product can be found on either the back or the bottom of the unit Please note them in the space provided below and keep for future reference MODEL NUMBER SC HTB770 SERIAL NUMBER 42 RQT9778 set up adjustments misadjustment of consumer controls improper maintenance power line surge lightning damage modification introduction of sand humidity or liquids commercial use such as hotel office restaurant or other business or rental use of the product or service by anyone other than a Factory Service Center or other Authorized Servicer or damage that is attributable to acts of God THERE ARE NO EXPRESS WARRANTIES EXCEPT AS LISTED UNDER LIMITED WARRANTY COVERAGE T
21. AVI Control What is VIERA Link HDAVI Control VIERA Link is a new name for EZ Sync VIERA Link HDAVI Control is a convenient function that offers linked operations of this system and a Panasonic TV VIERA under HDAVI Control You can use this function by connecting the equipment with an HDMI cable See the operating instructions for connected equipment for operational details Preparation Confirm that the HDMI connection has been made gt 26 27 Setthe HDAVI Control operations on the connected equipment e g TV For the optimal HDAVI Control operations change the following settings on the connected TV 1 Set the default speaker settings to this system Set the speaker selection settings to this system 4 Turn on all HDAVI Control compatible equipment and select the TV s input for this system so that the HDAVI Control function works properly Ifa device is connected to the HDMI IN terminal start play to check that the picture is displayed on the TV correctly When the connection or settings are changed repeat this procedure x1 The availability and function of the settings may vary depending on the TV Refer to the operating instructions for the TV for details x2 If the TV has a default speaker setting within the VIERA Link setting items choosing this system as the default speaker will automatically change the speaker selection to this
22. HE WARRANTOR IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THIS PRODUCT OR ARISING OUT OF ANY BREACH OF THIS WARRANTY As examples this excludes damages for lost time travel to and from the servicer loss of or damage to media or images data or other memory or recorded content The items listed are not exclusive but for illustration only ALL EXPRESS AND IMPLIED WARRANTIES INCLUDING THE WARRANTY OF MERCHANTABILITY ARE LIMITED TO THE PERIOD OF THE LIMITED WARRANTY Some states do not allow the exclusion or limitation of incidental or consequential damages or limitations on how long an implied warranty lasts so the exclusions may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from state to state If a problem with this product develops during or after the warranty period you may contact your dealer or Service Center If the problem is not handled to your satisfaction then write to the warrantor s Consumer Affairs Department at the addresses listed for the warrantor PARTS AND SERVICE WHICH ARE NOT COVERED BY THIS LIMITED WARRANTY ARE YOUR RESPONSIBILITY Customer Services Directory United States and Puerto Rico Obtain Product Information and Operating Assistance locate your nearest Dealer or Service Center purchase Parts and Accessories or make Customer Service and Literature requests by visiting our Web Site at or contac
23. Panasonic Owner s Manual Home Theater Audio System Model No SC HTB 70 OK JO OK O J Bluetooth Thank you for purchasing this product Please read these instructions carefully before using this product and save this manual for future use If you have any questions contact U S A and Puerto Rico 1 800 211 PANA 7262 Canada 1 800 561 5505 Register online at www panasonic com register U S customers only P RQT9778 1P IMPORTANT SAFETY INSTRUCTIONS Read these operating instructions carefully before using the unit Follow the safety instructions on the unit and the applicable safety instructions listed below Keep these operating instructions handy for future reference Read these instructions Keep these instructions Heed all warnings Follow all instructions Do not use this apparatus near water Clean only with dry cloth Do not block any ventilation openings Install in accordance with the manufacturer s instructions 8 Donot install near any heat sources such as radiators heat registers stoves or other apparatus including amplifiers that produce heat 9 Do not defeat the safety purpose of the polarized or grounding type plug A polarized plug has two blades with one wider than the other A grounding type plug has two blades and a third grounding prong The wide blade or the third prong are provided for your safety If the provided plug does not fit into your outlet consult
24. V remote control e f you turn off the main unit the TV speakers will be automatically activated Audio will automatically be output from this system if the TV is compatible to VIERA Link HDAVI Control 4 or later TV TV speakers are active The volume of this system is set to its minimum E Automatic input switching When the following operations are performed the main unit will automatically change the input to the corresponding source When play starts on an HDMI connected device When the TV input or the TV channel is changed x3 If the speaker output setting on the TV is set to this system the TV and the main unit turn on automatically Power on link E Power off link When the TV is turned off the main unit also turns off automatically This function does not work when Bluetooth is the source E Automatic lip sync function for HDAVI Control 3 or later Delay between audio and video is automatically adjusted by adding time lag to the audio output enabling you to enjoy smooth audio for the picture L The delay information is automatically set if the TV is compatible to VIERA Link HDAVI Control 3 or later and the VIERA Link is set to on Advanced operations Audio format indicator To display the current audio format Press and hold SOUND for more than 4 sec e The current audio format is indicated for 5 sec STADIUM indicator blinks Sc Dolby Digital is
25. a FULL HD 3D TV 3 2 n O d When the device has an optical digital audio output terminal e g Set top box OPTICAL OUT Refer to the operating instructions of the respective devices for the optimal connection Optical digital audio cable RQT9778 2 7 Speaker cable connection Match the connector shape and connect to the terminals of the same color RED GREEN WHITE Right speaker connector Center speaker connector Left speaker connector AC power supply cord connection e Connect only after all other connections are completed Toa household AC outlet AC power supply cord supplied e This system consumes a small amount of AC power amp 39 even when it is turned off In the interest of power conservation if you will not be using this system for a long time unplug it from the household AC outlet Saving energy The main unit is designed to conserve its power consumption and save energy e The main unit will automatically switch to standby mode when no signal is input and no operation is performed for approx 30 minutes 2 8 RQT9778 Active subwoofer wireless connection Preparation e Turn on the main unit EP Press ml Active subwoofer on off button
26. an deseo acenencayiinuetswaernnuuetecuss 6 This system SC HTB770 cao dewnnceccenienesnenernssunaneadenkenoeiaadennd ueaeatcniauenneniderdieaientaearoianieeneeatanins 6 PC CSS SSS tesa tancncus conendertaebansaquctpa EE REEE EE EASA AEE tenes 6 Control reference guide iriiaiciecenscteteetengemetmnGataesecaetnntesneusGentusuaeSeacbsnanetastnmenduiesedeeatenestewaeds 7 TIDIS Syster FLOM scine dooien eE r a E dons Aa rS EAE EONA ETETEA E 7 This system CR CAM eas aeisdacacesevastesdat acecaadesa tutte vende cant saidd vauiutieboalsaueaiddectilp a desedaeeneaddnatcupamesdetaadgsnidetas 8 Pee OLS CONMOL tigiy Sas tie setaactastesiann pata E E EEE EEEN 9 Getting started Step 1 Selecting the placement Method cc cece ceeeeeeeeeeeeeeeeeeeeeeneeseeneeseeeeeseaeees 10 The speaker Syst 9 ene eee ee ee ane reer EEE eee 11 WIG active SUD WOOT SE acicederepncnteaccscnsecesctineseiens sectclsiexos Era ONENE ESEESE ES EEEE DEEN EEEE 11 Wireless interferente cies cosa ssoorniccaise iceivne niin ino i ERE an E eE Eae DE EENE TA DTA 11 Step 2 Assembling the Speaker S cccccceceeeeeseeeeseeeeceeeeeeeeneeeeaeeeeeanesseanessoaneesoaaees 12 When attaching the speakers to a wall cccccsssscccceeeseeceeeseeeseeseesseeseesseesseesseaseeessagesessees 12 When placing the speakers on a table c ec ccccccceecceseeceeeeeeeeeeeeeeeeeseeeeseecessaeeesaeeeesaeesaees 19 Additional speaker fall prevention measures cccccceeec
27. angle of 45 as illustrated above x2 When attaching the cord to the center speaker make sure that the cord does not touch the speaker cable lead wire RQT9778 2 5 Step 3 Connections e Turn off all equipment before connection and read the appropriate operating instructions Do not connect the AC power supply cord until all other connections are completed E HDMI e The HDMI connection supports VIERA Link HDAVI Control 32 when used with a compatible Panasonic TV e Use the ARC compatible High Speed HDMI cables Non HDMI compliant cables cannot be utilized e t is recommended that you use Panasonic s HDMI cable E Connection with the TV d Verify if the TV s HDMI terminal is labeled HDMI ARC Connection differs depending on the label printed next to the HDMI terminal Labeled HDMI ARC Connection EY Not Labeled HDMI ARC Connection E E What is ARC ARC is an abbreviation of Audio Return Channel also known as HDMI ARC It refers to one of the HDMI functions When you connect the main unit to the terminal labeled HDMI ARC on the TV the optical digital audio cable that is usually required in order to listen to sound from a TV is no longer required and TV pictures and sound can be enjoyed with a single HDMI cable B Make the connection Labeled HDMI ARC HDMI IN ARC Be sure to connect to the TV s ARC compatible terminal Refer to the operating instructions
28. ceeececeeeeeseeeeeaeeeeseeeseeeeeseeeeesaesesaeeees 24 Step 3 Connections scii sete cecssecesecesescriwndciecateseteucuiessnesmsuidaduiseduasatedersdiusuuideaatwnceameaudseanes 26 Connection with the TV nc2acecenssu c2careanncenininarntacnmuteeieteniaens ew iereunetensacaouneqaiamlaubinmsemsasniending 26 Connection with other devices ccccccccsseccceesccceeecceeeecaueeeceusecsueseeseeeeseeeessueeessuseesaesessueeeses 27 Speaker CADIS connectoM asiiscissrenc saanziar antes vanes ninki niinn nera Einin EA E EENE aiian KETA ENE rE Ri 28 AC power SUDDIY c rd Connection s sssirssssscrirenirindstni cere iusiii nkra EEEn ERMEE EEEN EN ADRE EEA EE BANERA KEEA 28 Active subwoofer wireless connection ccccccecccsseeccaeeecceececeueecceeeeeseusessueessuusessueessaaeesseess 29 Bluetooth COMMeCtiON ccccccscsesececescecscscevececscececcecsvevevevececeeseavsvecscacacaceueavavavevesereeeteneneeveveres 29 Operations Using this system ssccisaccierctcs wince tinea ceiteinnicbsinesices tasnimaaticdneuahcceamecenenienieacenneebaduemscusieancnwaceneucine 30 SES OUN ssicaracettcesupacecicunensaangeaveeunedsextucsmeseeveccsmesusnouesneses neue nouuensaned E E 31 SOUNE MOOS areor et ane ee ence eae E E E een eee eee ere er cee 31 Linked operations with the TV VIERA Link HDAVI Control sas oe Rena N aN AA A E E A T 32 Advanced operations ccccccesceceeeeeeeseeeeneeeeneeeeseeeeneeeeneceeseeeaseesaeeeeeseaeesenesseneesenesanans 33
29. centre Link Support gt Panasonic Servicentre locator on www panasonic ca v Q S g Xx IF YOU SHIP THE PRODUCT TO A SERVICENTRE Carefully pack and send prepaid adequately insured and preferably in the original carton Include details of the defect claimed and proof of date of original purchase RQT9778 4 3 If you see this symbol Information on Disposal in other Countries outside the European Union This symbol is only valid in the European Union If you wish to discard this product please contact your local authorities or dealer and ask for the es correct method of disposal As an ENERGY STAR Partner p J Panasonic has determined that this product meets the ENERGY STAR guidelines for energy efficiency ENERGY STAR x For Canada only The word Participant is used in place of the word Partner Panasonic Consumer Marketing Panasonic Canada Inc En Company of North America 5770 Ambler Drive Division of Panasonic Corporation of Mississauga Ontario North America See E One Panasonic Way Secaucus a E New Jersey 07094 http www panasonic com Panasonic Corporation 2012 Printed in Malaysia RQT9778 1P i F1212RK1013
30. d e Choose a placement method that suits you best When attaching the speakers to a wall q v Place the speakers horizontally o D Place the front speakers vertically When placing the speakers on a table Place the speakers using the leg stands v Place the speakers using the support legs and speaker feet v Place the front speakers using the speaker bases v 1 0 RQT9778 Caution e This system is to be used only as indicated in these instructions Failure to do so may lead to damage to the amplifier and or the speakers and may result in the risk of fire Consult a qualified service person if damage has occurred or if you experience a sudden change in performance e Do not attempt to attach the speakers to a wall using methods other than those described in this manual The speaker system e Use a screwdriver for assembling the speakers e Do not hold the speakers in one hand to avoid injury you may drop the speakers when carrying them E When attaching the speakers to a wall The wall or pillar on which the speakers are to be attached should be capable of supporting 33 kg 72 8 Ibs per screw Consultation with a qualified installation specialist is recommended when attaching the speakers to a wall Improper attachment may result in damage to the wall and speakers and personal injury E When placing the speakers in front of the TV The speakers may block or interfere with the TV s va
31. d as the source On the Bluetooth device Select this system as the output source of the connected Bluetooth device and start the playback E When BD DVD AUX1 or AUX2 is selected as the source On the TV and the connected device Select the TV s input for this system and start the playback on the connected device E When AUX3 is selected as the source On the TV and the connected device Select the TV s input for the device connected to AUX3 terminal and start the playback on the connected device LL 8 Adjust the volume and sound effect level E To adjust the volume of this system Press VOL e Volume range 0 to 100 E To adjust the dialog effect level This setting will change the level of the Clear mode dialog effect gt 31 1 Press DIALOG LEVEL to display the current level 2 While the level is displayed Press DIALOG LEVEL to adjust the level indication Efect level Highest E To adjust the subwoofer level 1 Press SUBWOOFER to display the current level 2 While the level is displayed Press SUBWOOFER to adjust the level The level indication pattern is the same as dialog effect level E To mute the sound Press MUTE While muting the sound mode indicators blink simultaneously e To cancel press the button again or adjust the volume Muting is canceled if the main unit is turned off If this
32. e yy indicator lights a Bluetooth device is already connected with this system Disconnect it below Select SC HTB770 from the Bluetooth device s Bluetooth menu 3 2 7 te E Disconnecting a Bluetooth device Press and hold 6 until the dz indicator flashes slowly JER e When yy is selected as the source this system will automatically try and connect to the last connected Bluetooth device e The Bluetooth device will be disconnected if a different audio source e g TV is selected e Refer to the operating instructions of the Bluetooth device for further instruction on how to connect a Bluetooth device This system can only be connected to one device at a time e You can register up to 8 devices with this system If a 9th device is paired the device that has not been used for the longest time will be replaced e To change the sound quality refer to Bluetooth communication mode on page 34 RQT9778 29 Using this system Preparation Turn on the active subwoofer Turn on the TV and or connected device d Press 5 to turn on the main unit B Select the source Press To select INPUT TV gt BD DVD gt AUX1 lt AUX3 AUX2 lt i Q Bluetooth e This remote control cannot be used to control the operations of the connected devices SELECTOR te E When 3 is selecte
33. ect is reduced dialog effect level is still adjustable L To reset the setting return to the factory preset gt 36 LL To reset the setting return to the factory preset gt 36 E To turn off the volume limitation If a state of the lowered volume disturbs you every time the main unit turns on for example it is possible to turn off this function as follows While pressing and holding MUTE on the remote control press and hold VOL on the main unit for more than 4 sec All the indicators will blink once when the volume limitation is turned off To reset the setting return to the factory preset gt 36 RQT9778 3 5 72 S 2 Q Troubleshooting Before requesting service make the following checks If you are in doubt about some of the check points or if the solutions indicated in the following guide do not solve the problem refer to Customer Services Directory United States and Puerto Rico on page 42 if you reside in the U S A or Puerto Rico or refer to WARRANTY SERVICE on page 43 if you reside in Canada To return to the factory preset While the main unit is on press I on the main unit for more than 4 sec All the indicators will blink twice when this system is reset If this system does not operate as expected returning the settings to the factory preset may solve the problem The remote control code will return to 1 when this system is
34. equency Type A 19 pin 32 kHz 44 1 kHz 48 kHz 88 2 kHz 96 kHz only LPCM Audio format LPCM Dolby Digital DTS Digital Surround USB Port For service use only 3 8 RQT9778 SPEAKER SECTION Front speakers 3 way 3 speaker system Bass reflex type Speaker unit s Impedance 6 Q Woofer 5 7 cm 2 1 4 cone type Tweeter 2 5 cm 1 semi dome type Super tweeter Piezo type Output sound pressure 78 dB W 1 m Frequency range 90 Hz to 32 kHz 16 dB 100 Hz to 23 kHz 10 dB Center speaker 2 way 2 speaker system Bass reflex type Speaker unit s Impedance 6 Q Woofer 5 7 cm 2 1 4 cone type Super tweeter Piezo type Output sound pressure 78 dB W 1 m Frequency range 110 Hz to 20 kHz 16 dB 150 Hz to 16 kHz 10 dB Active subwoofer 1 way 1 speaker system Bass reflex type Woofer 16 cm 6 1 2 cone type Output sound pressure 80 dB W 1 m Frequency range 30 Hz to 180 Hz 16 dB 35 Hz to 160 Hz 10 dB WIRELESS SECTION Wireless module Frequency Range 2 40335 GHz to 2 47735 GHz No of channels 38 GENERAL Main unit 37 W Active subwoofer 20 W Power consumption In standby condition Main unit When the other connected devices are turned off Approx 0 25 W Active subwoofer Power switch release Approx 0 2 W Power supply AC 120 V 60 Hz Dimensions WxHxD Main unit 310 mmx45 mmx 188 mm 12 3 16 1 12h X7 She Active subwoofer 180 mmx408 mmx306 mm 7 3 32 X16 16 12 tHe
35. ersons The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the appliance THE FOLLOWING APPLIES ONLY IN THE U S A FCC Note This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help Any unauthorized changes or modifications to this equipment would void the user s authority
36. fice restaurant or other business or rental use of the product or service by anyone other than an Authorized Servicer or damage that is attributable to acts of God Dry cell batteries are also excluded from coverage under this warranty THIS EXPRESS LIMITED WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE INNO EVENT WILL PANASONIC CANADA INC BE LIABLE FOR ANY SPECIAL INDIRECT OR CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THIS PRODUCT OR ARISING OUT OF ANY BREACH OF ANY EXPRESS OR IMPLIED WARRANTY As examples this warranty excludes damages for lost time travel to and from the Authorized Servicer loss of or damage to media or images data or other memory or recorded content This list of items is not exhaustive but for illustration only In certain instances some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages or the exclusion of implied warranties so the above limitations and exclusions may not be applicable This warranty gives you specific legal rights and you may have other rights which vary depending on your province or territory WARRANTY SERVICE For product operation and information assistance please contact PRODUCT OPERATION ASSISTANCE Customer Care Centre Telephone 1 800 561 5505 Fax 905 238 2360 PRODUCT REPAIRS Please locate your nearest Authorized Servi
37. g down the speaker attached to the red connector cable is PEU CONNEGIOR sche placed on the left side With the speaker facing down the speaker attached to the white connector cable is to be placed on the right side White connector Keep the screws out of reach of children to prevent swallowing S 2 7 d ey White Align the higher or lower holes with the projecting parts on the speaker e By changing the position that the stand is attached to the projecting parts the height can be adjusted by 9 mm 1 32 Screw supplied Right speaker connector e Tighten securely Left speaker connector Screw hole RQT9778 1 9 Place the speakers using the support legs and speaker feet 2 Front 1 Center speaker 3 Speaker cables speakers nt WHITE Left i Noy RED Right GREEN Center 1 Metal bracket _ 2 Support legs _ 6 Screws BB 2 Speaker feet L 2Sp e For a safety measure to prevent the speakers from falling refer to page 24 To prevent damage or scratches lay down a soft cloth and perform the assembly on it ii Assemble the speakers following steps 1 and 2 of Place the speakers horizontally gt 12 13 B Attach the support legs and speaker feet With the speaker facing down the speaker attached to the red connector cable is Red Connector ighe placed on the left side With the speaker facing down the speaker attached to
38. hat the screw is in this speaker will likely fall if Right speaker connector Left speaker connector position moved to the left or right 1 4 RQT9778 iLi Place the front speakers vertically o The speakers can be wall mounted by drilling screws into the wall etc Make sure that the screw used and the wall are strong enough to support the weight of at least 33 kg 72 8 Ibs The screws and other items are not supplied as the type and size will vary with each installation e For details about the required screws refer to the diagram below the step Drive a screw into the wall gt 17 2 Front 1 Center speaker 3 Speaker cables speakers ay Oey WHITE Left ay RED Right GREEN Center 2 Stand necks _ 2 Side caps 4 Screws 2 Hook brackets e For a safety measure to prevent the speakers from falling refer to page 24 To prevent damage or scratches lay down a soft cloth and perform the assembly on it d Assemble the center speaker Attach the side caps and hook brackets to the speaker e There is no left and right for the center speaker Keep the screws out of reach of children to prevent swallowing S 3 O d O Hook bracket supplied Screw supplied e Tighten securely RQT9778 1 5 B Assemble the center speaker Connect the speaker cable Insert the wire fully taking care not to insert beyond the wire insulation
39. ifications and settings of a device it can fail to connect or some operations can be different This system supports Bluetooth security features But depending on the operating environment and or settings this security is possibly not sufficient Transmit data wirelessly to this system with caution This system cannot transmit data to a Bluetooth device E Range of use Use this device at a maximum range of 10 m 33 ft The range can decrease depending on the environment obstacles or interference E Interference from other devices e This system may not function properly and troubles such as noise and sound jumps may arise due to radio wave interference if the main unit is located too close to other Bluetooth devices or the devices that use the 2 4 GHz band e This system may not function properly if radio waves from a nearby broadcasting station etc are too strong mM Intended usage e This system is for normal general use only e Do not use this system near equipment or in an environment that is sensitive to radio frequency interference example airports hospitals laboratories etc Table of contents IMPORTANT SAFETY INSTRUCTIONS cccceccecececececececescececesueaeeeeeeeaeaeaeaueaeeeseeensaeeass 2 ANE CANS EE E E aie die en earn aca utc ccna a ean dd deena Pelee eda E ET 4 PBG Ut BOE G OC a r E E EAE E A E 4 Before use Supplied items cscs eas acc cee en nacewedencnemnsiuu ns etscemaua
40. in unit and active subwoofer JER e Product numbers are correct as of December 2012 These may be subject to change e For U S A and Puerto Rico To order accessories refer to Accessory Purchases United States and Puerto Rico on page 42 For Canada To order accessories call the dealer from whom you have made your purchase e The supplied AC power supply cord is for use with this system only Do not use it with other equipment Also do not use cords from other equipment with this system 6 RQT9778 Control reference guide This system Front 1 Standby on switch l Press to switch the unit from on to standby mode or vice versa In standby mode the unit is still consuming a small amount of power 2 Adjust the volume of this system 3 Select the input source TV gt BD DVD 3 AUX1 AUX3 AUX2 4 Input selector indicators a Bluetooth indicator Lights blue when the Bluetooth device is the audio source TV indicator Lights green when the TV is the audio source BD DVD indicator Lights amber when the device connected to the BD DVD terminal is the audio source AUX1 indicator Lights amber when the device connected to the AUX1 terminal is the audio source AUX2 indicator Lights amber when the device connected to the AUX2 terminal is the audio source AUX3 indica
41. kers Attach the stand neck e The two front speakers are interchangeable e Keep the screws out of reach of children to prevent swallowing Screw supplied e Tighten securely 3 Assemble the front speakers Insert the speaker cable through the speaker base and connect the speaker cables e Be sure to insert the speaker cable through the threading hole as indicated in the illustration Insert the wire fully White Blue line Insert the wire fully taking care not to insert beyond the wire insulation x If you have difficulty inserting the cable try straightening the speaker cable and then bending the cable about 20 mm 32 from the tip at an angle of approx 45 as illustrated above 2 2 RQT9778 4 Assemble the front speakers Attach the speaker base e The two front speakers are interchangeable e Keep the screws out of reach of children to prevent swallowing Screw supplied e Tighten securely Align the projecting parts with the holes on the speaker Press into the groove xe he x 4 2 Red connector The speaker attached to the red connector cable is to be placed on the right side White connector The speaker attached to the white connector cable is to be placed on the left side RQT9778 23 Additional speaker fall prevention measures To prevent the speakers from falling it is recommended as an additional protection measure to a
42. mpatible gt 26 0 Active subwoofer on off button gt 29 O AON gt ON O x The I D SET button is only used when the main unit is not paired with the active subwoofer gt 37 8 RQT9778 Remote control E Before using for the first time Remove the insulation sheet E To replace a button type battery Battery type CR2025 Lithium battery Ql Y V L 2 aa Turn the main unit on or off gt 30 Adjust the dialog effect level gt 30 Adjust the output level of the active subwoofer bass sound gt 30 Adjust the volume of this system gt 30 Mute the sound gt 30 Select the input source gt 30 TV gt BD DVD gt AUX1 G AUX3 AUX2 Select the Bluetooth device as the source gt 30 Select the sound mode gt 31 STANDARD gt STADIUM gt MUSIC STEREO lt NEWS lt CINEMA lt _ Set the button type battery with its mark facing upward Keep the button type battery out of reach of children to prevent swallowing E Remote control operation range The remote control signal sensor is located on the main unit e Use the remote control within the correct operation range Remote control signal sensor Operation range Distance Within approx 7 m 23 ft directly in front Angle Approx 30 left and right RQT9778 9 Step 1 Selecting the placement metho
43. n gt 33 e When the auto gain control is on gt 33 The indicator blinks for 5 sec e When the audio format is Dolby Digital gt 33 The indicator blinks for 5 sec e When the audio format is DTS gt 33 The indicator blinks for 5 sec e When the audio format is PCM gt 33 TV BD DVD AUXI AUX2 AUX3 STANDARD STADIUM MUSIC CINEMA TV BD DVD AUX1 AUX2 AUX3 STANDARD STADIUM CINEMA N74 es FN The indicator blinks for 10 sec e When the Bluetooth communication is mode 2 gt 34 The indicator blinks for 20 sec e When 3D surround effect and clear mode dialog effect are off gt 34 When the dual audio setting is Secondary SAP Secondary Audio Program 33 e When the auto gain control is off gt 33 The indicators blink for 20 sec When the dual audio setting is Main and Secondary gt 33 AUX2 AUX3 STANDARD STADIUM CINEMA LN SN SN SN SN SN SN SN 3 TV BD DVD AUXI AUX2 AUX3 STANDARD STADIUM MUSIC CINEMA NLS a a e e e LN x1 The indicator for the current status remains lit The indicators blink for 10 sec e When the remote control code is changed 35 The indicators blink once When changing the setting To reduce the clear mode dialog effect To turn off VIERA Link HDAVI Control and To turn off the volume limitation gt 35 The indicators blink twice e When the main unit is reset gt 36
44. n unit and active subwoofer Press ID SET on the rear of the active subwoofer for more than 3 sec The WIRELESS LINK indicator will blink in red 3 While pressing and holding INPUT SELECTOR on remote control press and hold VOL on the main unit for more than 4 sec The BD DVD indicator will blink and sound mode indicators light up in sequence When the wireless pairing is successful BD DVD indicator will stop flashing and WIRELESS LINK indicator lights green 4 Turn the main unit off and on e Consult your dealer if the problem persists v O S g x RQT9778 37 Specifications AMPLIFIER SECTION RMS output power Dolby Digital Mode Front ch L R ch 60 W per channel 6 Q 1 KHz 10 THD Center ch C ch 60 W per channel 6 Q 1 KHz 10 THD Subwoofer ch 120 W per channel 8 Q 100 Hz 10 THD Total RMS Dolby Digital mode power 300 W FTC output power Dolby Digital Mode Front ch L R ch 25 W per channel 6 Q 120 Hz to 20 kHz 1 0 THD Center ch C ch 25 W per channel 6 Q 120 Hz to 20 kHz 1 0 THD Subwoofer ch 40 W per channel 8 Q 60 Hz to 120 Hz 1 0 THD Total FTC Dolby Digital mode power 115 W TERMINAL SECTION HDAVI Control This unit supports HDAVI Control 5 function HDMI AV input BD DVD AUX1 AUX2 3 Input connector Type A 19 pin HDMI AV output TV ARC Output connector Digital audio input Optical digital input TV AUX3 2 Sampling fr
45. nstalled and operated keeping the radiator at least 20 cm 7 7 or more away from person s body excluding extremities hands wrists feet and ankles RQT9778 3 2 S Ke 3 D a Unit care M Clean this system with a soft dry cloth When dirt is heavy wring a cloth moistened in water tightly to wipe the dirt and then wipe it with a dry cloth e When cleaning the speakers use a fine cloth Do not use tissues or other materials towels etc that can fall apart Small grains may get stuck inside the speaker cover e Never use alcohol paint thinner or benzine to clean this system e Before using chemically treated cloth carefully read the instructions that came with the cloth E To dispose or transfer this system This system may keep the user settings information in the main unit If you discard the main unit either by disposal or transfer then follow the procedure to return all the settings to the factory presets to delete the user settings gt 36 To return to the factory preset e The operation history may be recorded in the memory of the main unit Manufactured under license from Dolby Laboratories Dolby Pro Logic and the double D symbol are trademarks of Dolby Laboratories Manufactured under license under U S Patent Nos 5 956 674 5 974 380 6 487 535 amp other U S and worldwide patents issued amp pending DTS the Symbol amp DTS and the Symbol together are registe
46. omatically When the main unit detects a problem a safety measure is activated and the main unit automatically switches to standby mode There is a problem with the amplifier Is the volume extremely high If so lower the volume Is this system placed in an extremely hot place If so move this system to a cooler place and wait a few moments and then try to turn it on again If the problem persists confirm the TV indicator and BD DVD indicator blink turn this system off remove the AC power supply cord and consult your dealer Please be sure to remember the indicators that were blinking and inform the dealer Active Subwoofer No power Ensure the AC power supply cord of the active subwoofer is connected properly After turning the subwoofer on it immediately turns off Unplug the AC power supply cord and consult your dealer No sound from the subwoofer Check that the active subwoofer is turned on Check that the WIRELESS LINK indicator lights green gt 29 The WIRELESS LINK indicator lights red There is no link between the main unit and the active subwoofer Check that the main unit is turned on Turn the active subwoofer off and then back on Alternatively turn the active subwoofer off disconnect the AC power supply cord and then reconnect it The active subwoofer and the main unit may not be paired correctly Try the following operation Wireless pairing Turn on the mai
47. or blinks A 3D surround effect and clear mode dialog effect is on STEREO indicator blinks 3D surround effect and clear mode dialog effect is off B While the setting is displayed press SOUND to change the setting e The setting changes each time SOUND is pressed e The indicator for the selected setting blinks for 20 sec and then exits the setting mode This setting will be reset to on when the main unit is turned off e When off is selected the dialog effect level cannot be adjusted Dimmer mode You can turn off dimmer mode and keep the LED indicators bright While pressing and holding INPUT SELECTOR on the remote control press and hold VOL on the main unit for more than 4 sec to turn off Dimmer mode e The indicator for the current condition will turn brighter The setting is maintained until it is changed again e Default setting of this function is on L To turn on dimmer mode repeat the operation above After performing the operation the indicator for the current condition will be dim Others E Remote control code When other Panasonic devices respond to this system s remote control change the remote control code on this system and the remote control Preparation Turn off all other Panasonic products Turn on the main unit Change the remote control code to code 2 1 Aim the remote control at the main unit s remote control sensor 2 Press and hold MUTE
48. place or refund will be made by Panasonic Canada Inc Technics Audio Product One 1 year parts and labour Panasonic BD DVD Product One 1 year parts and labour Panasonic Audio Receivers One 1 year parts and labour Home Theater Systems Product One 1 year parts and labour This warranty is given only to the original purchaser or the person for whom it was purchased as a gift of a Panasonic brand product mentioned above sold by an authorized Panasonic dealer in Canada and purchased and used in Canada which product was not sold as is and which product was delivered to you in new condition in the original packaging IN ORDER TO BE ELIGIBLE TO RECEIVE WARRANTY SERVICE HEREUNDER A PURCHASE RECEIPT OR OTHER PROOF OF DATE OF ORIGINAL PURCHASE SHOWING AMOUNT PAID AND PLACE OF PURCHASE IS REQUIRED LIMITATIONS AND EXCLUSIONS This warranty ONLY COVERS failures due to defects in materials or workmanship and DOES NOT COVER normal wear and tear or cosmetic damage The warranty ALSO DOES NOT COVER damages which occurred in shipment or failures which are caused by products not supplied by Panasonic Canada Inc or failures which result from accidents misuse abuse neglect mishandling misapplication alteration faulty installation set up adjustments misadjustment of consumer controls improper maintenance power line surge lightning damage modification introduction of sand humidity or liquids commercial use such as hotel of
49. ptical digital audio cable 26 e f the main unit is connected to a Panasonic TV and turned on using the button on the main unit or the remote control sound might not be output from this system In this case turn the main unit on using the TV s remote control gt 32 e f the connections are correct there might be a problem with the cables Redo the connections with different cables e Check the audio output settings on the connected device e f the BD DVD indicator flashes and there is no audio output try the following Turn the connected device off and then on Turn off the main unit remove the HDMI cable then reconnect the HDMI cable and turn the main unit back on The dual audio cannot be changed from main to secondary If the audio received from the connected device is not Dolby Dual Mono or the output setting is not Bitstream the setting cannot be changed from this system Change the setting on the connected device The volume is lowered when the main unit is turned on If the main unit is turned off with the volume setting in the greater half above 50 the main unit will automatically lower the volume to the middle 50 when the main unit is turned on gt 35 The dialog is too persistent or the dialog does not sound natural This system has a function to make the dialog stand out when the volume is low gt 35 There is no audio The power of the main unit turns off aut
50. rectly If the HDMI cable is connected to the wrong terminal HDMI IN or HDMI OUT this system will not operate correctly Turn the main unit off disconnect the AC power supply cord and reconnect the HDMI cable s 26 27 VIERA Link related operations no longer function properly e Check the VIERA Link setting on the connected devices Have you turned the VIERA Link settings off gt 35 When the HDMI connections are changed after a power failure or after the AC power supply cord has been removed VIERA Link operations may not function properly Turn on all the devices that are connected to the TV with an HDMI cable and then turn the TV on Turn off the VIERA Link settings of the TV and turn it on again For details refer to the operating instructions for the TV While the main unit and the TV are connected with the HDMI cable turn on the TV and then remove the main units AC power supply cord and reconnect it again The first few seconds of audio cannot be heard when using the HDMI connection This may occur during DVD Video chapter playback Change the digital audio output setting on the connected device from Bitstream to PCM When operating an HDMI compatible device of a different brand the main unit reacts in an unwanted manner HDAVI Control commands may use a different signal depending on the brand of the device In this case turn VIERA Link off gt 35 Bluetooth Pairing
51. red trademarks amp DTS Digital Surround and the DTS logos are trademarks of DTS Inc Product includes software DTS Inc All Rights Reserved HDMI the HDMI Logo and High Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries HDAVI Control is a trademark of Panasonic Corporation VIERA Link is a trademark of Panasonic Corporation EZ Sync is a trademark of Panasonic Corporation The Bluetooth word mark and logos are owned by the Bluetooth SIG Inc and any use of such marks by Panasonic Corporation is under license Other trademarks and trade names are those of their respective owners 4 RQT9778 About Bluetooth Panasonic bears no responsibility for data and or information that is compromised during a wireless transmission E Frequency band used This system uses the 2 4 GHz frequency band E Certification of this device e This system conforms to frequency restrictions and has received certification based on frequency laws Thus a wireless permit is not necessary The action below are punishable by law in some countries Taking apart or modifying the unit Removing specification indications E Restrictions of use e Wireless transmission and or usage with all Bluetooth equipped devices is not guaranteed e All devices must conform to standards set by Bluetooth SIG Inc e Depending on the spec
52. regular coloring occurs on your TV turn the TV off for about 30 minutes If it persists move the speakers further away from the TV Keep magnetized items away Magnetized cards watches etc can be damaged if placed too close to the active subwoofer and the speakers RQT9778 1 1 Step 2 Assembling the speakers When attaching the speakers to a wall _ Place the speakers horizontally The speakers can be wall mounted by drilling screws into the wall etc Make sure that the screw used and the wall are strong enough to support the weight of at least 33 kg 72 8 Ibs The screws and other items are not supplied as the type and size will vary with each installation e For details about the required screws refer to the diagram below the step Drive a screw into the wall gt 13 ron enter speaker peaker capies 2 Front 1 Cent k 3 Speaker cabl RED Right GREEN Center speakers ay wy WHITE Left 1 Metal bracket a 4 Screws e For a safety measure to prevent the speakers from falling refer to page 24 e To prevent damage or scratches lay down a soft cloth and perform the assembly on it ii Assemble the speakers e There is no left and right for the center speaker e The two front speakers are interchangeable e Keep the screws out of reach of children to prevent swallowing Screw supplied Tighten securely 1 2 RQT9778 B Connect the speaker cables or
53. rious sensors C A T S Contrast Automatic Tracking System sensor remote control sensor etc and the 3D Eyewear transmitters on a 3D compatible TV e If the leg stands are being used Change the height of the leg stands and or move the speakers further away from the TV If the TV still does not function correctly try removing the leg stands e If the leg stands are not used Move the speakers further away from the TV If the TV still does not function properly try placing them beside the TV gt 10 The active subwoofer When carrying the active subwoofer Do not hold the active subwoofer from this opening The parts inside may get damaged Always hold the bottom of the active subwoofer when moving it 3 S D te Q O E Wireless interference To avoid interference maintain the following distances between the main unit active subwoofer and other electronic devices that use the same radio frequency 2 4 GHz band Main unit active subwoofer a Ca Wireless router cordless phone and other esa electronic devices approx 2 m 6 1 2 ft Place the active subwoofer within a few meters of the main unit and in a horizontal position with the top panel facing upward e Do not use the main unit or the active subwoofer in a metal cabinet J Placing the active subwoofer too close to the walls and corners can result in excessive bass Cover walls and windows with thick curtains e f ir
54. t the power plug can be unplugged from the socket outlet immediately Button type battery Lithium battery Risk of fire explosion and burns Do not disassemble heat above 60 C 140 F or incinerate DO NOT INGEST BATTERY CHEMICAL BURN HAZARD This product contains a coin button cell battery If the coin button cell battery is swallowed it can cause severe internal burns in just 2 hours and can lead to death Keep new and used batteries away from children If the battery compartment does not close securely stop using the product and keep it away from children If you think batteries might have been swallowed or placed inside any part of the body seek immediate medical attention If any electrolyte should come into contact with your hands or clothes wash it off thoroughly with water If any electrolyte should come into contact with your eyes never rub the eyes Rinse eyes thoroughly with water and then consult a doctor lt For USA California only gt This product contains a CR Coin Cell Lithium Battery which contains Perchlorate Material special handling may apply See www dtsc ca gov hazardouswaste perchlorate E CAUTION Unit e Do not place sources of naked flames such as lighted candles on this unit Placement To reduce the risk of fire electric shock or product damage Do not install or place this unit in a bookcase built in cabinet or in another confined space Ensure this unit is
55. t us via the web at http www panasonic com contactinfo You may also contact us directly at 1 800 211 PANA 7262 Monday Friday 9am 9pm Saturday Sunday 10am 7pm EST For hearing or speech impaired TTY users TTY 1 877 833 8855 Accessory Purchases United States and Puerto Rico Purchase Parts Accessories and Instruction Books online for all Panasonic Products by visiting our Web Site at http www pstc panasonic com Or send your request by E mail to npcparts us panasonic com You may also contact us directly at 1 800 332 5368 Phone 1 800 237 9080 Fax Only Monday Friday 9am 9pm EST Panasonic National Parts Center 20421 84th Ave S Kent WA 98032 We accept Visa MasterCard Discover Card American Express For hearing or speech impaired TTY users TTY 1 866 605 1277 As of October 2012 User memo DATE OF PURCHASE DEALER NAME DEALER ADDRESS TELEPHONE NUMBER Limited Warranty ONLY FOR CANADA Panasonic Canada Inc 5770 Ambler Drive Mississauga Ontario L4W 2T3 PANASONIC PRODUCT LIMITED WARRANTY Panasonic Canada Inc warrants this product to be free from defects in material and workmanship under normal use and for a period as stated below from the date of original purchase agrees to at its option either a repair your product with new or refurbished parts b replace it with a new or a refurbished equivalent value product or c refund your purchase price The decision to repair re
56. teries y Applicable Not Only Non Rechargeable Batteries 10 Days Applicable During the Labor warranty period there will be no charge for labor During the Parts warranty period there will be no charge for parts This Limited Warranty excludes both parts and labor for non rechargeable batteries antennas and cosmetic parts cabinet This warranty only applies to products purchased and serviced in the United States or Puerto Rico This warranty is extended only to the original purchaser of a new product which was not sold as is Mail In Service For assistance in the U S A and Puerto Rico in obtaining repairs please ship the product prepaid to Panasonic Exchange Center 4900 George McVay Drive Suite B McAllen TX 78503 panacare us panasonic com Online Repair Request To submit a new repair request and for quick repair status visit our Web Site at www panasonic com repair When shipping the unit carefully pack include all supplied accessories listed in the Owner s Manual and send it prepaid adequately insured and packed well in a carton box When shipping Lithium lon batteries please visit our Web Site at www panasonic com BatteryHandling as Panasonic is committed to providing the most up to date information Include a letter detailing the complaint a return address and provide a daytime phone number where you can be reached A valid registered receipt is required under the Limited Warranty IF REP
57. the volume is lowered for night time viewing Dolby Virtual Speaker 3D surround effect Clear mode dialog To turn off Dolby Virtual Speaker and the 3D surround effects select STEREO as the sound mode amp right To turn off the 3D surround and the Clear mode dialog effects refer to Using the Dolby Virtual Speaker effect gt 34 Sound modes By changing the sound mode it is possible to enjoy the sound that is suitable to the TV program or image from the connected device E To select the sound mode Press SOUND STANDARD STADIUM MUSIC STEREO NEWS CINEMA e The indicator for the selected sound mode lights e g STANDARD e C C C C SN STANDARD Produces a sound best suited for Factory preset dramas and comedy shows STADIUM MUSIC CINEMA STEREO The setting is maintained until it is changed again Produces a highly realistic sound for live broadcasts of sports Re creates the sound of musical instruments and songs with an expansive sound Produces a powerful three dimensional sound unique to movies Enhances the voices of news and sports commentaries for clearer hearing You can play any source in stereo Dolby Virtual Speaker and 3D surround effects are turned off S 2 Q RQT9778 3 1 Linked operations with the TV VIERA Link HD
58. the audio format MUSIC indicator blinks SUS DTS is the audio format CINEMA indicator blinks PCM is the audio format L Audio format is not indicated when H is selected as the source Changing the dual audio Change the dual audio from main to secondary This setting will only work if the audio output setting on the connected TV or player etc is set to Bitstream and dual audio is available in the audio source als Press and hold MUTE for more than 4 sec STANDARD indicator blinks Main Factory preset NZ O 7 STEREO indicator blinks Secondary SAP Secondary Audio Program When and both blink Main and secondary B While the setting is displayed press MUTE to change the setting e The setting changes each time MUTE is pressed e The indicator for the selected setting blinks for 20 sec and then exits the setting mode The setting is maintained until it is changed again Auto gain control With this function you can prevent sudden loud sounds The output will be reduced automatically when the input exceeds a certain level Press and hold INPUT SELECTOR on the remote control for more than 4 sec STANDARD indicator blinks ay Auto gain control is on LN STEREO indicator blinks Auto gain control is off AE Factory preset While the setting is displayed press INPUT SELECTOR on the remote control to change the setting e
59. tor Lights amber when the device connected to the AUX3 terminal is the audio source Main unit Active subwoofer Sound mode indicators STANDARD indicator Lights when STANDARD is the current sound mode STADIUM indicator 2 Lights when STADIUM is the current sound mode a MUSIC indicator Q V L 2 aa Lights when MUSIC is the current sound mode CINEMA indicator Lights when CINEMA is the current sound mode K NEWS indicator Lights when NEWS is the current sound mode STEREO indicator Lights when STEREO is the current sound mode Remote control signal sensor gt 9 WIRELESS LINK indicator gt 29 x1 The indicators will also blink in various conditions 40 x2 The indicator blinks for 5 sec when the main unit detects an audio format To manually verify the current audio format and the corresponding indicators refer to page 33 Audio format indicator RQT9778 7 E This system Rear UX wo HOM SPEAKERS HAUT PARLEURS AVIN ol CENTER el Hne AUX2 AUX1 BD DVD is HDMI1 L TV SPEAKERS HAUT PEURS a TV AU _ OPT1 o4 FO a i 8 9 AC IN terminal gt 28 Speaker terminals gt 28 TV terminal gt 26 AUX3 terminal gt 27 USB port for service use only AUX2 terminal gt 27 AUX1 terminal gt 27 BD DVD terminal gt 27 HDMI OUT terminal ARC co
60. ttach the speakers to the wall or table with a fall prevention cord hereafter cord LL e Consultation with a qualified installation specialist concerning the appropriate procedure when attaching to a concrete wall ora surface that may not have strong enough support is recommended 13 17 Improper attachment may result in damage to the wall and speakers and personal injury Use a cord that is capable of supporting over 10 kg 22 05 Ibs with a diameter of about 1 5 mm 16 The speaker fall prevention measure is to minimize the possibility of damage and harm but it does not completely guarantee this effect Keep the screws out of reach of children to prevent swallowing Make sure that the slack of the cord is minimal Depending on the placement of the speakers the screwing position of the screw eye may differ When attaching the speakers horizontally Wall mounting On a table Cord Screw eye Wall x If the cord cannot be threaded through the holes try bending the cord in 2 locations about 10 mm 1 32 apart from the tip at an angle of 45 as illustrated above 2 4 RQT9778 p When attaching the speakers vertically Wall mounting On a table Getting started Cord Wall Screw eye Approx 150 mm 5 29 32 x1 If the cord cannot be threaded through the holes try bending the cord in 2 locations about 10 mm 1 32 apart from the tip at an
Download Pdf Manuals
Related Search