EK Water Blocks 3831109855324
Contents
1. LLING WATER BLOCK 1 PLACING THERMAL PADS ON PCB Place thermal pads on chips so that numbers on chips 2 PLACING GPU REINFORCE PLATE ON PCB Place metal reinforce and washer on match size of thermal pads Thermal pad number 1 2 3 and 4 will have to be cut by user to PCB as shown on picture below and screw it in with enclosed M3x4 screws Please match all small power regulation chips EKWB made sure users have more than enough use encased PVC washers under each screw Make sure you use fasten screws pads to cover all surfaces that need to be covered to make block fully functional You can equally and do not use too much force also use small drop of thermal grease on chips to make thermal pads more adhesive SERE E 4 l l l l l l l at i l l l l l l T i l l l l l 1 a eC 1444 sald zs Y ams p s s it bees E Orientation sou g tut ss ian ar na of reinforcer TTE Any tae A em a Hd aa is important O E PVC washer All disclosures notices and warranty conditions are being written on the back of the box Released on 16 of November 2010 Revision 1 0 3 PLACING STANDOFFS ON BLOCK Brass standoffs are obligatory in order to attach this 4 ATTACHING BLOCK TO GRAPHIC CARD By using Philips screwdriver screw in water block to the printed circuit board of the graphics card Please use the2. e board and bracket Wipe off the remains by using card non abrasive cloth or Q tip as shown on sample photo of the original thermal compound until the components and circuit board are completely clean EKWB does not recommend using any liquids for removing paste ETTI 2000 bg 7 000 2000 rE s t a m lt a s Ap i ie Re lea aga en ae POG Enine sS g 5 5 u er ee teen ee Seme cer oF el g A ArH g gs ee ose cre p ea gaa bf i F aiana Le b Ee ji o TS Om ap me i PPS iage ir Ea ETTTTTTT we CEEC TTTI i PRC ECETTI PETET 4 bees gt MLA ae A 3 APPLYING THERMAL COMPOUND Apply thermal compound lightly coat 4 CUTTING THERMAL PADS Your block comes with thermal pads which have to be placed on both GPUs and bridge chip with electrically non conductive thermal interface chips PLEASE REMOVE FOIL ON BOTH SIDES OF THERMAL PADS PRIOR TO INSTALLATION material TIM for example Arctic Cooling MX 2 or MX 4 thermal WARNING DIMENSION BELLOW ARE SCALED grease EKWB recommends to apply thermal grease in cross form for best All thermal pads need to be cut to pieces of appropriate size to fit onto RAM chips pad 1 performance see sample picture R125 inductors pad 2 R33 inductors pad 4 MOSFET chips and IC drivers pad 3 PAD ee PAD 0 5mm 60 oc a EEEE fia SPARE PAD 1mm o e 1 5mm STEP 3 INSTA
3. ekwD Installation and mounting manual for EK FC580 GTX water block This product is intended for installation only by expert users Please consult with a qualified technician for installation Improper installation may result in damage to your equipment EK Water Blocks assumes no liability whatsoever expressed or implied for the use of these products nor their installation The following instructions are subject to change without notice Please visit our web site at www ekwaterblocks com for updates Before installation of this product please read important notice disclosure and warranty conditions printed on the back of the box The barb hose fittings require only a small amount of force to screw them in otherwise the high flow fittings might break These fittings do not need to be tightened with much force because the liquid seal is made using o rings STEP 1 GENERAL INFORMATION Sample picture of NVidia GeForce 580 GTX graphic card STEP 2 PREPARING YOUR GRAPHIC CARD 1 REMOVING STOCK COOLER Remove encircled screws on the bracket erty ce r pe rn pi una aA sa APRS SCRE CKOSS FerAl OPS STEP 2 cont PREPARING YOUR GRAPHIC CARD 1 cont REMOVING STOCK COOLER Remove all encircled screws All heat sink assembly 2 CLEANING THE PCB Carefully detach the original heat sink after removing all screws and backplate should be removed There are 20 screws on the back of the graphic fasteners securing it to th
4. encased key to enclosed M3x4 screws EKWB recommends start screwing the screws around the screw them to the copper base of the water block GPU core and continue outwards Use 10 screws M3x4 Use 10 enclosed PVC washers This way you will diminish possibility z Tightening the standoff f of damaging the PCB due to high screw tension ae f nS P STEP 4 CHECKING FOR CONTACTS Temporarily remove the water block to check for uniform surface contact between the block and the components Note the pattern of contact on a piece of paper Then repeat substeps in previous section to reattach the block In case you fail to obtain good contact please check again your thermal pad thickness or contact our support service STEP 5 SECURING I O BRACKET STEP 6 FITTING POSITIONING Use one M3x6 screw one PVC washer and one M3 nut to secure the I O Please use spacer only on copper base if you use fitting with G1 4 thread longer than 5mm see also known as PCI bracket firmly to the circuit board This will allow the sample picture Screw in the fittings and plugs please use spacers only on copper base for computer chassis to carry the weight of the waterblock thus reducing the fittings Use 6mm Allen key to screw in and tighten new EK Plug G1 4 Attach the liquid cooling tension on the PCI express slot Tighten the screw with Philips screwdriver tubes and connect the water block s into the cooling circuit EKWB recommends using
5. high flow while holding the M3 nut with your thumbs firmly fittings with the EK FC 580 GTX series water blocks To ensure that the tubes are securely attached to the barb fittings please use hose clamps or an appropriate substitute The use of an algaecide is always recommended for any liquid cooling system You can use any hole as an inlet outlet port G1 4 Spacer Gasket O ring Plug with o ring PVC washer 6mm Allen key Plug with o ring STEP 6 INSERTING CARD IN YOUR PC CASE Carefully lift your card with installed block and insert it in your PC case Please bear in mind that your card suddenly withstands extra weight thus again be very careful not to bend it or cause any other unneeded moves that might damage your card or block during installation REQUIRED TOOLS AND MOUNTING SCREWS Va Scissors philips screwdriver 14 x screws M3x4 DIN7985 1 x M3x6 DIN7985 1 x M3 nut 15 x PVC washers All disclosures notices and warranty conditions are being written on the back of the box Released on 16 of November 2010 Revision 1 0
Download Pdf Manuals
Related Search