Technoline WS 6825 weather station
Contents
1. WS6825 INSTRUCTION MANUAL LED WEATHER STATION WITH RADIO CONTROLLED CLOCK AND ALARM RCC INDICATOR INDOOR TEMPERATURE WEATHER FORECAST OUTDOOR TEMPERATURE SNOOZE DIMMER HANGER HOLE UP RF SET BATTERY DOOR ALARM INSERT 1 x CR2032 BATTERY INSIDE THE DOWM WAVE BATTERY COMPARTMENT AC DC ADAPTOR W UUWN UUE S INSERT AC DC ADAPTOR JACK LED INSERT 2 x AAA RESET BATTERIES OUTDOOR TEMPERATURE SENSOR Words in the figure Back view CO O S MM TS ee _ o i CO o i i EO O soome ooo ug o ooo S ETHER S S __ Lor RENE ADAPTOR JACK ETE NN EMEN C O NEN INSERT 1 x CR2032 BATTERY INSIDE THE BATTERY COMPARTMENT BATTERY DOOR HANGER HOLE OUTDOOR TEMPERATURE SENSOR CHANNEL 1 CHANNEL 2 CHANNEL 3 INSERT 2 x AAA BATTERIES ENVIRONMENTAL RECEPTION EFFECTS The weather station obtains the accurate time with wireless technology Same as all wireless devices the reception is maybe affected by the following circumstances Long transmitting distance Nearby mountains and valleys Among tall buildings Near freeway railway airports high voltage cable etc Near construction site Inside concrete buildings Near electrical appliances computers TV s etc Inside moving vehicles Near metallic structures Place the station at a location with optimal signal i e cl2. ess level which you originally selected after the radio controlled time reception is completed During DCF reception all buttons do not function and it does not take temperature measurement The temperature readings will get stable and become more accurate after the station clock is powered up for around 30 minutes To cancel DCF reception permanently Press and hold the V WAVE the button at the same time for 2 seconds the station will give 2 short beeps and the radio controlled function is permanently disabled To resume the radio controlled function press and hold the WAVE and the button at the same time for 2 seconds the station will give 2 short beeps and will start DCF reception immediately THE WEATHER FORECAST The weather station has a built in barometer which measures the barometric pressure After power up the display shows SUNNY amp CLOUDY icon The weather station takes around 24 hours to gather data of barometric pressure changes and predicts next 6 12 hours weather conditions There are four types of weather display in the weather station Sunny Sunny amp Cloudy Cloudy Note Moving the weather station within the house or in the vicinity will causing a sudden change in the attitude of the station and it affects the accuracy and correctness of the weather forecast After the weather station is powered up it will take around 24 hours to get stable The weather icons on the display give a reference to
3. he clock will return to normal mode in around 10 seconds if no further press of any other buttons To turn on or off the alarm Single press the ALM button during normal time display to turn on or off the alarm When the alarm function is turned on the AL icon appears on top of the time digits Note Alarm duration is 2 minutes To use the snooze function When time reaches the set alarm time the station will give a beep sound to wake you up The AL icon will flash 1 Press SNOOZE once to stop the alarm temporarily AL icon keeps flashing The alarm will beep again after the set snooze duration 2 To stop the daily alarm press any button except the SNOOZE button when alarm is beeping The alarm will stop and AL icon becomes static The Alarm will beep again same time next day DIMMER FUNCTION Press the SNOOZE DIMMER button to adjust high or low brightness of the LED display TROUBLE SHOOTING In case the station shows false digits it maybe affected by electrostatic discharge or interferences from other devices Press the RESET button on the back of the station The station will be reset to default setting of time and calendar and it will start to receive radio controlled time signal again If you lose the outdoor temperature When the outdoor temperature digits show the wireless transmission is either interrupted or lost Press and hold the button of the station then press the RESET button located on the back of the outdoor t
4. lashes Receiving DCF signal do icon flashing Successful reception 2 icon becomes static Failed reception 2 icon disappear During reception press the v WAVE button will display reception mode and signal strength indication When strong DCF signal is detected display shows with 3 bars uw on When weak or no DCF signal is detected display shows F or During reception the signal strength may move from 1 bar to 2 bars to 3 bars This is normal since the clock is detecting DCF signal and other signals in the air at the same time Press the SET button will return to the time display with F icon flashing Successful reception or failed reception Icon becomes static on stop blinking when reception is successful T Icon disappears when reception is failed Automatic reception and manual reception The station starts automatic reception everyday at 1 00 2 00 and 3 00 If it fails to receive the DCF signal at 3 00 it will start reception at 4 00 If it fails again it will start reception at 5 00 If it fails again it will start automatic reception at 1 00 again in the next day For manual reception simply press and hold the V WAVE button the station will gives a short beep and starts manual reception Press and hold the WV WAVE button to stop DCF reception When the weather station is receiving the radio controlled time signal the display will turn dimmer It will resume to the brightn
5. ose to a window and away from metal surfaces or electrical appliances QUICK SETUP Step 1 Keep the station and outdoor sensor next to each other Slide open the battery cover at the back of the outdoor sensor Make sure the channel selector is set at position 1 top position then insert 2 x AAA batteries not included into the outdoor sensor by observing the correct polarity signs inside the battery compartment Replace the battery door Step 2 Insert the AC DC adaptor to any 230V AC household outlet Then insert the DC jack to the back case of the station Insert the stand to the bottom of the weather station Step 3 Slide open the battery cover at the back of the station then insert 1 x CR2032 Lithium battery not included to the battery compartment Make sure polarity of the battery is facing up Then replace the battery cover Step 4 Peel off the protective label on the front The weather station is ready to work for you The station will receive data signal from the outdoor sensor in few seconds Then place the outdoor sensor in a dry and shaded area outdoor BACK UP BATTERIES When the power supply is not in use the station will be powered by the back up batteries The LED display is turned off but time and alarm time remain stored also in the event of a power failure DCF SIGNAL RECEPTION AND SIGNAL INDICATOR gt gt After the station is powered up starts to receive DCF signal The icon f
6. ransmitter If you continue to lose the outdoor temperature display try placing the transmitter in a different location until you have smooth transmission of temperature data Note Keep in mind that the outdoor transmitter only has a 30 meter transmission range in open area with no obstructions Each obstruction between the transmitter and the station roof walls floors ceilings thick trees etc will effectively cut the transmission range in half CARE OF THIS ITEM Do not expose the unit to extreme temperature water or direct sunlight Avoid contact with any corrosive materials Do not subject the unit to excessive force dust or humidity Do not open the inner back case or tamper with any components of this unit SPECIFICATIONS Operation temperature 0 C to 45 C Temperature measuring range Indoor 0 C to 50 C display shows HH H LL L if out of this range Outdoor 50 C to 70 C display shows HH H LL L if out of this range Temperature resolution 1 Alarm duration 2 minutes Snooze duration 5 to 60 minutes Consideration of duty according to the battery law atteries do not belong to domestic waste because they could cause damages o N Old batteries do not belong to domestic waste b th ld d f health and environment End users are committed by law to bring back needed batteries to distributors and other collecting points
7. the next 6 12 hours weather conditions It may not match with the current weather condition outside TIME SETTING 1 Press and hold the SET button for 2 seconds hour digits flash Press the the button to set the hours 2 Then pressthe SET button again the minute digits flash Press the W or the button to set the minutes 3 Then press the SET button again display shows 05 and flash Press or the A button to set snooze duration from 5 minutes to 60 minutes 4 Then press the SET button again display shows 00 and flash Press the button to set the time zone 01 GMT 0 United Kingdom 00 GMT 1 Central Europaen time 01 GMT 2 Eastern Europaen time Note Time zone can only set when the clock successfully receives a radio signal 5 Press the SET button again to store the settings and return to normal time display The clock will return to normal mode in around 10 seconds if no further press of any other buttons Note The time is displayed in 24 hour display format ALARM SETTING default alarm setting is 6 00 AM 1 Press and hold the ALM button until the AL icon appears on the display the hour digits flash Press the V or the button to set the desired alarm hours 2 Press the ALM button again the minute digits flash Press the W or the button to set the desired alarm minutes 3 Press the ALM button again to store the alarm settings and return to normal time display T
Download Pdf Manuals
Related Search