Peerless WL-SR560M-200 flat panel floorstand
Contents
1. multi washer 6 M8 x 40 mm 4 aoe Mee 920 1152 I D 22 5 6 mm 4 540 1057 I D 34 8 7 mm 4 940 1059 Additional Wireless Components wireless transmitter 1 vga to rca adapter 1 plastic stand 1 remote 1 install guide 1 180 1202 180 1006 180 1205 180 1207 LIT 0905 3v battery 1 12v power adapter 1 ir flasher 1 hdmi cable 2 instruction sheet 1 180 0008 180 1004 180 1009 600 0234 180 9023 5 of 19 ISSUED 08 24 12 SHEET 180 9037 2 10 30 12 Insert right leg S into base housing D as shown in fig 1 1 Then align holes in right leg with holes in base housing D Fasten base housing to right leg using two 3 8 16 x 1 5 bolts W and two joint connectors V Tighten using 3 16 allen wrench Z and 7 32 allen wrench M as shown in fig 1 2 NOTE Left and right legs can be identified by looking at the cart from the front Repeat for left side with left leg R fig 1 1 fig 1 2 FRONT OF LEG Insert casters U amp T into holes of support legs R amp S and hand thread to secure Attach casters with brake U to the back of left and right support legs R amp S Attach casters without brake T to front of support legs as shown NOTE Lock brakes on casters to avoid sudden movements during installation HAND THREAD HOLD WHEEL 6 of 19 ISSUED 08 24 12 SHEET 180 9037 2 10 30 12 Attach upright G to base D2. 180 9037 2 10 30 12 Install the cable tie anchor FF onto the inside Plug the power cord from your display into the triple 21 back wall of the power enclosure BB Remove the 22 tap grounded outlet as shown Coil up the excess adhesive backing from the anchor and press into cord and secure with a cable tie GG inserting it place in the area shown through the cable tie anchor FF and around the coiled cord TRIPLE TAP GROUNDED OUTLET 23 Close the top cover of the power module assembly D Place the cords inside the cable management sheath BB making sure that the power adapter cords run Il by pushing the cables through the slit in the underneath the cable opening as shown below sheath NOTE The sheath may need to be trimmed Re install the M5 x 10mm phillips screws to length before installing cords M5 x 10mm SCREWS CABLE OPENING Plug the component cable s from your display 26 Plug extension cord not included into power adapter HDMI shown into the wireless receiver 17 of 19 ISSUED 08 24 12 SHEET 180 9037 2 10 30 12 Mounting and Removing Flat Panel Screen A WARNING e Always use an assistant or mechanical lifting equipment to safely lift and position the plasma television then slowly swing screen in as shown Turn screws of adapter plate F clockwise at least six times to prevent screen from being removed as shown in detail 7 NOTE Tighten using 4 mm allen wrench N Screen can be
3. as shown in fig 3 1 using three 3 8 16 x 2 5 socket screws L and M10 x 402ID lock washers X Tighten screws using 7 32 allen wrench M NOTE Be sure cord management holes are in the configuration shown in fig 3 2 fig 3 2 CORD MANAGEMENT HOLES 7 of 19 ISSUED 08 24 12 SHEET 180 9037 2 10 30 12 Slide shelf support C onto upright G so that 1 4 20 nuts J slide into slots of upright G as shown in figure 5 1 and detail 1 Slide shelf support to desired height level then tighten 1 4 20 x 12mm screws I using 4 mm allen wrench N NOTE MAXIMUM OF TWO SHELVES Max height of top shelf is 34 from base Max height of second shelf is 28 from base DETAIL 1 8 of 19 ISSUED 08 24 12 SHEET 180 9037 2 10 30 12 Attaching Metal Shelf Attach shelf pan P to shelf support C using six 8 32 nylock nuts O as shown below Use an adjustable wrench to tighten six 8 32 nylock nuts Q A WARNING e This shelf is intended for use with equipment weighing NO more than 50 Ibs 22 7 kg that fits evenly accross the surface of shelf pan P Use with other equipment may result in instability and cause personal injury or property damage 9 of 19 ISSUED 08 24 12 SHEET 180 9037 2 10 30 12 Loosely attach six 1 4 20 x 12 mm screws I and Slide screen mount bracket A onto upright G so D 1 4 20 nuts J to screen mount bra
4. adjusted horizontally if desired 27 Hook adapter brackets F onto universal plate E NOTE It is important to lock screen down To lock the screen down fully tighten screws to adapter bracket as shown in detail 7 To remove screen from mount loosen screws swing screen away from mount and lift screen off of mount DETAIL 7 Cord Management Run extension cord not included through upright G using cord 28 management holes CORD MANAGEMENT D j Z e NO A ww J To complete the installation of your wireless mount please refer to the HD Flow User s Manual and the HD Flow Install Guide included 18 of 19 ISSUED 08 24 12 SHEET 180 9037 2 10 30 12 2012 Peerless Industries Inc Peerless AV is a registered trademark of Peerless Industries Inc All rights reserved All other brand and product names are trademarks or registered trademarks of their respective owners LIMITED WARRANTY Peerless Industries Inc Peerless AV warrants to original end users of Peerless AV products that Peerless AV products will be free from defects in material and workmanship under normal use for the periods listed below from the date of purchase by the original end user At its option Peerless AV will repair or replace with new or refurbished products or parts or refund the purchase price of any Peerless AV product which fails to conform
5. ation as shown in fig 11 2 Once in position tighten the four 1 4 20 x 12 mm screws I using 4mm allen wrench N 0 0 0 0 0 A INSIDE NOTCH ed DA NOTE For mounting patterns smaller than VESA 400 use large enclosure mounting bracket DD Loosely attach the enclosure mounting brackets CC or DD to the power module assembly BB with two 1 4 20 x 12 mm screws I and two 1 4 20 nuts EE as shown in fig 12 1 NOTE The enclosure mounting bracket can be installed with the inside notch facing downward if additional side to side adjustment is needed Attach the mounting brackets CC or DD open end of notch facing downward to the adapter bracket F with two 1 4 20 x 12 mm screws I and two 1 4 20 nuts EE as shown in fig 12 2 Adjust the position of the power module assembly BB to your desired location as shown in fig 12 2 Once in position tighten the four 1 4 20 x 12 mm screws I using 4mm allen wrench N INSIDE NOTCH 11 of 14 ISSUED 11 14 11 SHEET 180 9007 1 Installing Adapter Brackets to Universal Plate A WARNING e Tighten screws so adapter brackets are firmly attached Do not tighten with excessive force Overtightening can cause stress damage to screws greatly reducing their holding power and possibly causing screw heads to become detached Tighten to 40 in lb 4 5 N M maximum torque e If screws do
6. bly AA as shown in detail 4 Open the enclosure to expose the wireless receiver and IR unit Remove the M5 x 10mm phillips screws and open the power module assembly BB as shown in detail 5 M5 X 10mm SCREWS Cal AA oe DETAIL 4 DETAIL Untie the wireless receiver power adapter cord and route as shown below Plug the end of the power adapter into the outlet marked DC on the wireless receiver as shown in detail 6 Coil up the excess cord and secure with a cable tie HH Store the coiled cord between the power adapter and the power module wall as shown WIRELESS RECEIVER POWER ADAPTER DISPLAY NOT SHOWN FOR CLARITY DETAIL 6 15 of 19 ISSUED 08 24 12 SHEET 180 9037 2 10 30 12 O Locate the IR receiver inside of the wireless receiver enclosure shown in figure 19 1 Remove the tie from the cable and position the IR receiver on the display within line of sight of your remote as shown in figure 19 2 Remove the adhesive backing from the IR receiver eye and attach to the display Coil up the excess cord near the wireless receiver enclosure AA and secure with a cable tie HH Store the coiled cord back inside of the enclosure fig 19 2 IR RECIEVER IR RECIEVER fig 19 1 Close the top cover of the wireless receiver assembly AA making sure that the power adapter cords run underneath the cable opening as shown below Re install the two 8 screws CABLE OPENING 16 of 19 ISSUED 08 24 12 SHEET
7. cket A O that 1 4 20 nuts J slide into slots of upright G as shown in figure 8 1 and detail 2 Slide screen mount bracket to desired position level then tighten 1 4 20 x 12 mm screws I using 4 mm allen wrench N DETAIL 2 fig 8 1 Insert two 1 4 20 x 12 mm screws I into screen mount bracket A leaving 3 16 of exposed thread as shown in figure 10 1 and detail 3 it DETAIL3 fig 10 1 10 of 19 ISSUED 08 24 12 SHEET 180 9037 2 10 30 12 Wireless Receiver and Power Enclosure Installation fig 12 1 NOTE For mounting patterns smaller than VESA 400 use large enclosure mounting bracket DD NOTE The Wireless Receiver Assembly AA and Power Module Assembly BB position can be interchanged based on the display s connector panel location Install Wireless Receiver Assembly on the side closest to the connector panel Loosely attach the enclosure mounting brackets CC or DD to the wireless receiver assembly AA with two 1 4 20 x 12 mm screws I and two 1 4 20 nuts EE as shown in fig 11 1 NOTE The enclosure mounting bracket can be installed with the inside notch facing downward if additional side to side adjustment is needed Attach the mounting brackets CC or DD open end of notch facing downward to the adapter bracket F with two 1 4 20 x 12 mm screws I and two 1 4 20 nuts EE as shown in fig 11 2 Adjust the position of the receiver assembly AA to your desired loc
8. er or other person is authorized to modify or extend this Limited Warranty or impose any obligation on Peerless AV in connection with the sale of any Peerless AV product This warranty gives specific legal rights and you may also have other rights which vary from state to state Product Warranty Period Mounts 5 years Furniture 1 year Cables 25 years Cleaning Products 1 year Electronic Products and components 1 year fi peerless ANV www peerless av com 2012 Peerless Industries Inc 19 of 19 ISSUED 08 24 12 SHEET 180 9037 2 10 30 12
9. n areas with heavy traffic Tools Needed for Assembly e level e phillips screwdriver Table of Conten FS ENS cect patito acest ge dee ested eto carte tea tla A AAT A E E AEE AAAS 34 5 E O Or 5 eee ee nee E EE ee E eee EE ee eee eee EATE 6 Wireless Receiver Assembly and Power Module Assembly Installation ccccssccccsseceeceeeeeeeeeeeeeeeeeesaeeeeeeaeeeeneeeeesseeeeeas 11 HstalingAdapi r SAC ONS secsecsensicidn e EE E E EEEE AEE EA O 12 Attaching Universal Adapter Plate eestecnnn es auteatraetes tdatiens dese scienaewen cncauncsccacactesan ones near siateameancluaisscaseuacnaacteaniaid ode dden esd easesesiisa ane 14 Wireless Receiver Assembly and Power Module Assembly Setup cccccssscceccsseeccceeeceeeeeesseeeceaeeeeseeaeeesseseseeeseeaneeeeeas 15 cord Mando 0 lt 1 eee nee ene E ee een ee ee A eee 18 2 of 19 ISSUED 08 24 12 SHEET 180 9037 2 10 30 12 Before you begin make sure all parts shown are included with your product Parts may appear slightly different than illustrated Parts List WL SR560M 200 Part Number NSKXES lt cCHMDWOVOZSErFe rPAttmMvovowp Description screen mount bracket hook plate shelf support base universal plate adapter bracket upright top cover 1 4 20 x 12mm decorative screw 1 4 20mm nut 3 8 16 x 2 5 socket screw 7 32 allen wrench 4 mm allen wrench 8 32 nylock nut shelf pan 6 mm allen wrench left leg right leg wheel caster wheel cas
10. n t get three complete turns in the screen inserts or if screws bottom out and bracket is still not tightly secured damage may occur to screen or product may fail screen face side down Refer to screen manufacturers instructions or customer service for removing any knobs base cover or screw s on the back of the screen to prepare mounting These need to be removed to allow the adapter brackets to be attached To prevent scratching the screen set a cloth on a flat level surface that will support the weight of the screen Place Position adapter brackets F over mounting holes on back of screen Adjust the position of assemblies AA and BB so that they are at least 32 apart Make sure assemblies AA and BB are evenly spaced from the adapter brackets Tighten screws I to lock position of assemblies AA and BB Select the small medium large or extra large screws from the baffled fastener pack then attach adapter brackets to screen following figure 13 1 NOTE Top and bottom mounting holes must be used for attaching brackets Verify that all holes are properly aligned and then tighten screws using a security allen wrench 32 Min ___ BB CENTER BRACKETS JI VERTICALLY ON BACK J4 Lal OF SCREEN A Notes MULTI WASHER e The number of fasteners used will Vary MEDIUM HOLE FOR M5 SCREWS depending upon the type of screen e Multi washers and spacers may not be SMALL HOLE FOR M4 SCREWS used depending upo
11. n the type of screen LARGE HOLE FOR M6 SCREWS e Use the corresponding hole in the multi washer that matches your screw size as shown 12 of 19 ISSUED 08 24 12 SHEET 180 9037 2 10 30 12 Begin with longer length screw hand thread through multi washer adapter bracket and spacer in that order into screen as shown below Screw must make at least three full turns into the mounting hole and fit snug into place Do not over tighten If screw cannot make three full turns into the screen select a shorter length screw from the baffled fastener pack Repeat for remaining mounting holes level brackets and tighten screws SCREEN fig 13 1 MULTIL WASHER SPACER ae SCREW BRACKET F If you have any questions please call Peerless customer care at 1 800 865 2112 13 of 19 ISSUED 08 24 12 SHEET 180 9037 2 10 30 12 Attaching Universal Adapter Plate Attach Universal Plate E to hook plate B using D four M10 x 15 mm socket screws JJ Tighten screws using 6 mm allen wrench Q Attach hook plate B to screen mount bracket A Insert two 1 4 20 x 12 mm screws I into holes indicated below for desired screen orientation Tighten all screws using 4 mm allen wrench N No Tilt 2 Backward Tilt 5 Forward Tilt 14 of 19 ISSUED 08 24 12 SHEET 180 9037 2 10 30 12 Wireless Receiver Assembly and Power Module Assembly Setup Remove the two 8 screws securing the cover of the wireless receiver assem
12. peerless Installation and Assembly Wireless TV Cart for 47 to 65 Flat Panel Displays Models WL SR560M 200 Max Load Capacity 150 Ib 68 kg screen 50 Ib 22 7 kg per shelf 2300 White Oak Circle Aurora Il 60502 800 865 2112 Fax 800 359 6500 www peerless av com ISSUED 08 24 12 SHEET 180 9037 2 10 30 12 NOTE Read entire instruction sheet before you start installation and assembly A WARNING e Do not begin to install your Peerless product until you have read and understood the instructions and warnings contained in this Installation Sheet If you have any questions regarding any of the instructions or warnings for US customers please call Peerless customer care at 1 800 865 2112 for all international customers please contact your local distributor This product should only be installed by someone of good mechanical aptitude and fully understands these instructions Never exceed the Maximum Load Capacity on page 1 Always use an assistant or mechanical lifting equipment to safely lift and position equipment Tighten screws firmly but do not overtighten Overtightening can damage the items greatly reducing their holding power The cart is not affixed or secured to the floor and may therefore tip over and or fall if screen and or stand is shaken or hit Always monitor children and do not let children play alone around stand as they could get hurt by a falling screen Not recommended for use i
13. ter brake joint connector nut 3 8 16 x 1 5 screw bolt M10 x 402 ID lock washer 3 16 allen wrench wireless receiver assembly power module assembly enclosure mounting bracket small enclosure mounting bracket large lock nut 1 4 20 cable tie anchor cable tie 187 x 7 5 lg cable tie 04 x 5 75 lg cable management sheath M10 x 15 mm socket screw 3 of 19 201 1156 201 1157 201 1158 009 1223 201 1110 201 1510 580 1180 590 1210 920 2325 930 1050 920 9550 960 9715 960 9646 930 1038 009 1225 060 9716 009 1296 009 1295 600 0044 600 0045 930 1037 520 1329 540 9424 560 0071 180 1092 180 1015 120 1195 120 1196 530 1021 590 9469 590 1168 960 9711 090 9468 920 9262 s N l 1 N O N A NONO ARA 2 a a 0O RAANNGa anna naa DON W ISSUED 08 24 12 SHEET 180 9037 2 10 30 12 Some parts may appear slightly different than illustrated 4 of 19 ISSUED 08 24 12 SHEET 180 9037 2 10 30 12 Security Adapter Bracket Fasteners 510 1079 M5 x 12 mm 4 M6 x 12 mm 4 E 520 1064 520 1050 M8 x 15 mm 520 aa M6 x 20 mm 4 520 9554 M5 x 25 mm 4 520 1122 Q Q O M4 x 25 mm 4 520 1067
14. with this warranty In no event shall the duration of any implied warranty of merchantability or fitness for a particular purpose be longer than the period of the applicable express warranty set forth above Some states do not allow limitations on how long an implied warranty lasts so the above limitation may not apply to you This warranty does not cover damage caused by a service or repairs by the customer or a person who is not authorized for such service or repairs by Peerless AV b the failure to utilize proper packing when returning the product c incorrect installation or the failure to follow Peerless AV s instructions or warnings when installing using or storing the product or d misuse or accident in transit or otherwise including in cases of third party actions and force majeure This warranty also does not cover corrosion or rust resulting from damaged scratched or chipped paint or other surfaces In no event shall Peerless AV be liable for incidental or consequential damages or damages arising from the theft of any product whether or not secured by a security device which may be included with the Peerless AV product Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation or exclusion may not apply to you This warranty is in lieu of all other warranties express or implied and is the sole remedy with respect to product defects No dealer distributor install
Download Pdf Manuals
Related Search