Sennheiser HSL-10
Contents
1. button Affix the foam block to the phone hook button so that the phone handset pushes down the phone hook button see page 9 picture 5 If the foam block is too big for the phone hook button cut the foam block smaller 10 Further information In case of further questions please contact your vendor or alternatively your local Sennheiser representative For more information e g regarding problem solutions warranty conditions etc please also see our website www sennheisercommunications com under FAQ frequently asked questions or Products Wireless solutions and HSL 10 Accessories Accessory Part No Attachment parts 000000 Extension 000000 Cable with two modular plugs RJ 11 6 6 length 30 cm 000000 Microphone cable 000000 11 Specifications Overall unit Dimensions Weight Temperature range Power source Max lifting height Max load Microphone Length of cable Sensitivity 94 dB SPL 12 77x110x42cm 80g 5 to 40 C 6 V DC via base station gt 25 mm 200g 40 cm 43 dBV 142. lever should move Connecting the handset lifter to the telephone Note gt You can use the adhesive mounting tape only once Therefore we recommend not to remove the backing from the tape before you have determined the correct attachment position as follows With the handset put on hold the HSL 10 handset lifter between the telephone and the handset as close to the handset loudspeaker as possible In order to check whether the HSL 10 is in the correct position or not press the hook button on your mobile device or the base station respectively The position is correct if the lifting pad raises only the loudspeaker side of the handset and you can hear a dial tone Remove the backing from the adhesive tape and affix the HSL 10 with the adhesive tape Adjusting the lifting height a gt Press and hold down for two seconds both the P2 button and the P1 button The LED 6 alternately flashes red and green gt Release the buttons The lifting pad raises to the currently adjusted height E gt Increase or decrease the lifting height by pressing the P2 increase or P1 E decrease button until you can hear the dial tone gt Save the settings by pressing and holding down for two seconds both the P2 button and the P1 button Teaching the ring tones of your telephone to the HSL 10 You can teach two different ring tones to your HSL 10 This is required if e your telephone supports
3. manual 1 double sided adhesive tape for the microphone 1 lateral extension 1 extension block Operating elements P2 button Lifting pad P1 button Adhesive mounting tape LED Microphone fastening position Modular socket Microphone socket Microphone Hole of the Microphone 00009 Setting up the handset lifter Prior to connecting the HSL 10 handset lifter to your telephone first install and set up your wireless system BW 900 or DW 800 Attaching the microphone The procedure for attaching the microphone depends on where the ringing loudspeaker of your telephone is located If the loudspeaker is located under the handset gt Attach the microphone to the lifting pad in the fastening position E If the loudspeaker is located in a different place gt Attach the microphone with the double sided adhesive tape to the loudspeaker in such a way that it is placed directly on the loudspeaker 6 gt Always make sure not to cover the hole of the microphone with the double sided adhesive tape El Connect the jack plug of the microphone to the microphone socket Connecting the handset lifter to the base station a gt gt Connect the ACCESSORIES socket on the base station with the handset lifter s modular socket using the cable provided The LED lights up green five times if the base station is connected to power Test the HSL 10 by pressing the hook button on the base station The
4. In these cases the handset does not push down the hook button sufficiently and the call is not terminated To solve this problem you can affix the extension block to the hook button to ensure that it is pushed down sufficiently E gt Affix the extension block to the hook button as seen in the illustration If problems occur Problem Possible reason Remedial measures When pressing the hook button on the mobile device or base station you do not hear a dial tone in your headset The lifting height is not sufficient Adjust the lifting height see page 8 Although your phone is ringing you cannot hear the ring tone in your headset The HSL 10 microphone hole does not face the phone loudspeaker Re position the HSL 10 so that the microphone hole faces the phone loudspeaker HSL 10 does not recognize the ring tone Teach the ring tones of your phone to the HSL 10 see page 8 You hear a ring tone in your headset when another phone is ringing The HSL 10 is not adjusted to the ring tone of your phone Teach the ring tones of your phone to the HSL 10 see page 8 The phone handset slips off the lifting pad The lateral extension of the lifting pad is too short Replace the lateral extension of the lifting pad see page 9 You terminate the call on your headset but your phone is not hung up There is not contact between the phone handset and the phone hook
5. Instruction Manual Bedienungsanleitung Notice d emploi Istruzioni per l uso Instrucciones de uso Gebruiksaanwijzing Betjeningsvejledning Handhavande Manual English icsicccsscsssscssssesssorsesesstseadesedcsessseesas 3 Deutsch 15 Francais Italiano Espanol Nederlands HSL 10 handset lifter instruction manual Safety information ON 4 Related documents 4 Service description 5 Delivery includes 5 Operating elements RA 6 Setting up the handset lifter P Attaching the microphone 6 Connecting the handset lifter to the base Staa NAE AE TOE 7 Connecting the handset lifter to the telephone 7 Adjusting the lifting height 8 Teaching the ring tones of your telephone to the HSL IO riada 8 Replacing the lateral extension of the A TN 9 Affixing the extension block 9 If problems occur asociadas 10 Further information s dseusaebees Sisde 11 Accessories AN Sassusgeesstnsns 11 Specifications We have designed this product to give you reliable operation over many years Over half a century of accumulated expertise in the design and manufacture of high quality electro acoustic equipment have made Sennheiser a world leading company in this field Pleas
6. e take a few moments to read these instructions carefully as we want you to enjoy your new Sennheiser product quickly and to the fullest Safety information Disclaimer e Never disassemble or modify the HSL 10 If the housing is opened by customers in breach of this instruction the warranty becomes null and void e Never move the lifting pad by hand During use e Use the HSL 10 in dry places only and keep liquids and small electrically conductive parts away from the HSL 10 and its connecting sockets e Make sure that only the handset and no other objects are placed on the lifting pad Otherwise the lifting pad cannot lift up the handset Cleaning e For cleaning the HSL 10 use a dry cloth only Do not use any solvents or cleansing agents Related documents e BW 900 instruction manual and quick start guide e DW 800 instruction manual Service description g The HSL 10 handset lifter completes wireless systems like BW 900 and DW 800 from Sennheiser HSL 10 automatically picks up the handset of your office phone thus allowing you to operate your telephone even from the distance i e when you are not sitting at your desk Thanks to its unique ring tone detection via a high quality microphone the HSL 10 reliably recognizes the office phone ringing and forwards the call to your headset Delivery includes 1 HSL 10 handset lifter 1 microphone with cable and 2 5 mm mono jack plug 1 cable with two RJ 11 connectors 1 instruction
7. two different ring tones e g for external and internal calls e you hear a ring tone in your headset although not your telephone but another telephone in the vicinity is ringing e you can not hear a ring tone through your headset even your telephone is ringing Teaching ring tone 1 Set your telephone to ring tone 1 Make sure that ring tone 1 differs from the ring tones of other telephones in the vicinity gt Adjust the ring tone level to comfort gt Press and hold the P1 button until the LED flashes green gt Let your phone ring If recording has been successful the LED flashes red twice 8 Teaching ring tone 2 a gt Record ring tone 2 in the same way as described for ring 1 but press the P2 button until the LED flashes red The LED flashes green twice if the recording was succesful In your headset you will hear a ring tone when the HSL 10 recognizes ring tone 1 or 2 Replacing the lateral extension of the lifting pad If the lateral extension is not long enough to lift up the handset or if the handset tends to slip off the extension you can install a longer one instead E gt Replace the lateral extension as seen in the illustration Affixing the extension block When you terminate a call via the headset the HSL 10 usually hangs up the phone by replacing the handset which then pushes down the telephones hook button With some telephone types however this may not work properly
Download Pdf Manuals
Related Search