Premier Mounts ECM-3763Q flat panel ceiling mount
Contents
1. Mounting Bracket Arm Please see Page 10 for attachment instructions Page 5 b 4 A Installing the Ceiling Mount A 2 NPT threaded pipe must be firmly secured to the ceiling structure before performing the following steps For more height flexibility use Premier Mounts adjustable height ceiling adapter AST 2446 sold separately The Phillips set screw must be backed out in order for the NPT threaded pipe to attach to the threaded coupler Align the ECM 3763Q threaded coupler with the threaded end of the NPT threaded pipe Thread the ECM 3763Q onto the NPT threaded pipe and rotate the ECM 3763Q coupler clockwise until the coupler is fully threaded onto the NPT threaded pipe The coupler must be threaded onto the NPT threaded pipe a minimum of four 4 complete turns Once the ECM 3763Q has been firmly threaded to the 2 NPT threaded pipe use a screwdriver to tighten the Phillips set screw on the threaded coupler Ensure that all connections are secure and tight before proceeding to the next step Proceed to the Selecting the Appropriate Mounting Hardware section Page 6 Minimum four complete turns Quad Mount ECM 3763Q 4 aS Ri v SA V e 2 NPT Pipe Set Screw Threaded Coupler Installation Instructions ECM 3763Q 24 Selecting the Mounting Hardware Insert a sma2. Installation Instructions Page 3 gt 4 4 ECM 3763Q Parts List cont d Standard Hardware M4 x 16mm Phillips Head Screw Qty 32 M4 x 25mm Phillips Head Screw Qty 16 M5 x 16mm Phillips Head Screw Qty 24 M5 x 20mm Phillips Head Screw Qty 24 M5 x 25mm Phillips Head Screw Qty 16 M5 x 50mm Phillips Head Screw Qty 16 M6 x 12mm Phillips Head Screw Qty 32 Universal Spacers Qty 96 Y Flat Washer Metal Qty 24 Page 4 M6 x 20mm Phillips Head Screw Qty 24 M6 x 30mm Phillips Head Screw Qty 24 M8 x 20mm Phillips Head Screw Qty 24 M8 x 25mm Phillips Head Screw Qty 24 M8 x 30mm Phillips Head Screw Qty 24 M8 x 35mm Phillips Head Screw Qty 16 M8 x 70mm Phillips Head Screw Qty 16 M6 x 12mm Hex Head Bolt Qty16 M6 Split Lock Washer Qty 16 Griplate Washers Qty 32 Installation Instructions ECM 3763Q Features Installation Instructions Decorative Cover Please refer to Page 11 for instructions on how to install the decorative Quad Mount Please see Page 6 for installation instructions Please see Page 6 for installation instructions Elliptical Tilt Mount Please see Page 9 for installation procedures for the elliptical tilt mount
3. Premier Mounts Attn Warranty Claim 3130 East Miraloma Ave Anaheim CA 92806 How State Law Applies THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE Disclaimer Premier Mounts intends to make this manual accurate and complete However Premier Mounts makes no claim that the information contained herein covers all details conditions or variations nor does it provide for every possible contingency in connection with the installation or use of this product The information contained in this document is subject to change without notice or obligation of any kind Premier Mounts makes no representation of warranty expressed or implied regarding the information contained herein Premier Mounts assumes no responsibility for accuracy completeness or sufficiency of the information contained in this document Premier Mounts 2011 Installation Instructions Page 13
4. on the center bottom edge of the flat panel Using the upper hand gently pull the top of the flat panel towards you while the lower hand gently pushes the bottom of the flat panel away from you fin If additional tilt friction is required tighten the lower nut and lower bolt only to increase the tilt friction Technical Specifications All measurements are in inches mm Page 12 ECM 3763Q Adjusting the Flat Panel to the Original Position Place one hand at the center top edge of the flat panel Place the other hand on the center bottom edge of the flat panel Using the upper hand gently push the top of the flat panel towards the wall while the lower hand gently pulls the bottom of the flat panel away from the wall Lower Bolt Lower Nut Installation Instructions ECM 3763Q P Warranty PREMIER MOUNTS LIMITED LIFETIME WARRANTY What and Who is Covered by this Limited Warranty and for How Long Premier Mounts warrants this product to be free from defects in material and workmanship for the lifetime of the original owner of this product The limited warranty is valid only for the original purchaser of the product What Premier Mounts Will Do At the sole option of Premier Mounts Premier Mounts will repair or replace any product or product part that is defective If Premier Mounts chooses to replace a defective pro
5. DEVICE WHEN LIFTING THE FLAT PANEL INTO PLACE PRIOR TO THE INSTALLATION OF THIS PRODUCT THE INSTALLATION INSTRUCTIONS MUST BE READ AND COMPLETELY UNDERSTOOD TO PREVENT PERSONAL INJURY AND PROPERTY DAMAGE KEEP THESE INSTALLATION INSTRUCTIONS IN AN EASILY ACCESSIBLE LOCATION FOR FUTURE REFERENCE PREMIER MOUNTS DOES NOT WARRANT AGAINST DAMAGE CAUSED BY THE USE OF ANY PREMIER MOUNTS PRODUCT FOR PURPOSES OTHER THAN THOSE FOR WHICH IT WAS DESIGNED OR DAMAGE CAUSED BY UNAUTHORIZED ATTACHMENTS OR MODIFICATIONS AND IS NOT RESPONSIBLE FOR ANY DAMAGES CLAIMS DEMANDS SUITS ACTIONS OR CAUSES OF ACTION OF WHATEVER KIND RESULTING FROM ARISING OUT OF OR IN ANY MANNER RELATING TO ANY SUCH USE ATTACHMENTS OR MODIFICATIONS O gt SAFETY MEASURES MUST BE PRACTICED AT ALL TIMES DURING THE ASSEMBLY OF THIS PRODUCT USE PROPER SAFETY GEAR AND TOOLS FOR THE ASSEMBLY PROCEDURE TO PREVENT PERSONAL INJURY At least two qualified people should perform the assembly procedure Personal injury and or property damage can result from dropping or mishandling the flat panel Be aware of the mounting environment If drilling and or cutting into the mounting surface always make sure that there are no electrical wires in the ceiling Cutting or drilling into an electrical line may cause serious personal injury Make sure there are no water or natural gas lines inside the ceiling where the mount is to be located Cutting or drilling into a water or gas line may cause s
6. above the larger mounting hole Insert and tighten an M6 x 25mm Pan Combo screw in the larger mounting hole of each mounting bracket arm Place the first decorative cover over the first mounting bracket arm and push firmly into place Repeat Step 1 for the next decorative cover Align the mounting holes On each decorative cover insert and tighten an M4 x 8mm Pan Combo screw in the smaller mounting hole ty The decorative covers should easily go over the M6 x 25mm Pan Combo screws Repeat the Attaching Decorative Covers instructions to attach decorative covers to the next flat panel A Do not over tighten these screws Cable Management Route the cables through the cable access holes and to their respective locations Remove the plastic covers route the cables and gently re attach the plastic covers The cables may then be routed through the coupler up the ceiling adapter and into the ceiling to a predetermined power source Proceed to Tilt Positioning section Installation Instructions Mounting Bracket Arm M6 x 25mm Pan Combo Screw Decorative Cover M4 x 8mm Screw Screwdriver Source or A V Cable Page 11 b 4 22 Tilt Positioning Adjusting the Flat Panel Friction Tilt Angle Place one hand at the center top edge of the flat panel Place the other hand
7. cD PREMIER Cat MOUNTS CREATING POSITIVE CUSTOMER EXPERIENCES INSTALLATION INSTRUCTIONS Elliptical Ceiling Mount for 37 to 63 Flat Panels Model ECM 3763Q NORTH AMERICA EUROPE 3130 East Miraloma Avenue Unit 3 The Moorings Business Park Anaheim CA 92806 USA Channel Way Longford USA and Canada Coventry CV6 6RH UK Phone 1 800 368 9700 Phone 44 0 24 7664 4105 Fax 1 800 832 4888 Fax 44 0 24 7664 4165 Other Locations Phone 001 714 632 7100 Fax 001 714 632 1044 9531 007 044 02 gt 4 E ECM 3763Q lmStallation TOONS esner N E de luesaneaussien spuluenedeananartad nied saniaadeerenngas 3 Pans Ubbecreronssnoinr i dee a nS deee inlaw deedne ereedentdecd seen faevddededmdee S 3 Mounting Hand Walo ceson enon AAA decease atisien sare aee aan abaaseaeete 4 FEAOG orian E E scraper tay eben yan on ciate a eateerd lida aaa 5 Installing the Ceiling MOUNt cee iis csteredetsacensihsdcees entdacces ne plcccaseiaeaddcans ceuleceetnephucependpatcech O meacageleaagae 6 selecting the Mounting Hardware iiciicesicisieteiteietseeslsiacrecdesianniedinidaadidennaddvacdesdanntedes idaveeel leanase tiadheta ante 7 Griplate Washer Installation ccccccceceeeeeeeceeccaeceeeeeeeeeeeceececaaeaaeeeeeee
8. d by flat panels Do not place excessive pressure on the back of the flat panel as this may damage your flat panel The Griplate Washer must be installed between the head of the mounting screw and the mounting bracket as shown Does your flat panel have Recessed mount points Uneven mount points Acurved back Any obstruction near the mount point If Yes you must install nylon spacers Remove the mounting brackets Griplate washers and mounting screws from the back of the flat panel Proceed to the Mounting S Nylon Spacer Installation section a es i f Griplate Washer If No skip to the Flat Panel Installation section Nylon Spacer Installation Mounting Bracket Premier Mounts nylon spacers allow you to attach the mounting bracket to flat panels which have recessed or uneven mount points Each nylon spacer will add distance between the mounting bracket and your flat Flat Panel panel The nylon spacers must only be installed between Nylon Spacer the mounting bracket and your flat panel The nylon spacers will fit M4 M5 M6 and M8 screw sizes Proceed to the Elliptical Tilt Mount Installation section G CCCeGG p26 AS ooo 0029 00000000000000 Page 8 Installation Instructions 4 ECM 3763Q A Inserting the Hex Head Bolts Locate the two 2 upper mounting holes located on th
9. duct or part a replacement product or part will be shipped to you at no charge but you must pay any labor costs What is Not Covered Limitations PREMIER MOUNTS DISCLAIMS ANY LIABILITY FOR DAMAGE TO MOUNTS ADAPTERS DISPLAYS PROJECTORS OTHER PROPERTY OR PERSONAL INJURY RESULTING IN WHOLE OR IN PART FROM IMPROPER INSTALLATION MODIFICATION USE OR MISUSE OF ITS PRODUCTS PREMIER MOUNTS DISCLAIMS ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE PREMIER MOUNTS IS NOT RESPONSIBLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES INCLUDING BUT NOT LIMITED TO INABILITY TO USE ITS PRODUCTS OR LABOR COSTS FOR REMOVING AND REPLACING DEFECTIVE PRODUCTS OR PARTS SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU What Customers Must Do for Limited Warranty Service If you discover a problem that you think may be covered by the warranty you MUST REPORT it in writing to the address below within thirty 30 days Proof of purchase an original sales receipt from the original consumer purchaser must accompany all warranty claims Warranty claims must also include a description of the problem the purchaser s name address and telephone number General inquiries can be addressed to Premier Mounts Customer Service at 1 800 368 9700 Warranty claims will not be accepted over the phone or by fax
10. e back of the elliptical tilt mount Attach two 2 M6 x 12mm hex head bolts and two M6 Lock 2 M6 split flat washers A Split Washer Thread the hex bolts into the hole until there is a Ya gap between the head of the hex head bolt and the mounting surface of the elliptical tilt mount Repeat Steps 1 through 3 for all four of the oe elliptical tilt mounts a Gap Do not completely tighten the hex head bolts at re M6 x 12mm this time T gt Hex Bolt Proceed to Elliptical Tilt Mount Installation section Upper Mounting Hole Elliptical Tilt Mount Installation The following steps must be completed by two people Do not release the elliptical tilt mount until the hex head bolts are resting fully in the keyhole slots Align the hex head with the keyhole slot Gently insert the hex head through the keyhole slot and lower the elliptical tilt mount Align the lower mounting holes of the dual mounting bracket with the lower mounting points on the elliptical tilt mount Thread two 2 M6 x 12mm hex head bolts two 2 M6 split flat washers into the mounting holes Keyhole Slot M6 x 12mm Hex Bolt and Split Flat Washer Use a 10mm wrench and tighten all four 4 M6 x 12mm hex head bolts Repeat Steps 1 through 5 for mounting the remaining elliptical tilt mounts f Tol eae AR Proceed to Attaching the Flat Panel section 10mm Wrench Installatio
11. eeeeeeseccenaecaeeeeeeeeseesesnccuaeeeeeeeneess 8 Nylon Spacer IMS tallatiOn asrni S dues 2d ia OE ts madietls rails eeennss 8 Inserting the Hex Head BOIS asiria a aaa a e a aa Ea aaa a Aaaa Ta e a aaa Naa 9 Elliptical Tilt Mount INStallatiOn wsiaszscciverateoedssscuteccevecccdderveduduediieeneveceevaauveerusteead adevbnededeuneysauuees TEE EEEE AAE 9 Attaching the Flat Panel erroria A sath epanenshe sag heitsn rap nannnn AA 10 Attaching the Decorative COVES iii wsede gel aide nie dain adv dite ee nad 11 Gable Management esir s A sesdeataancdeaeaahdd ntaea ua feels taaaancdenmanyaeaateeaaa S 11 TIE POSIMIONING lt 4c s scactuqemersconcdexsaandsanenunanacetinsandcaesuasnad ideas veanenand vaadhuaduanshanseeay sdaadteeuasaadauestaansee a E 12 Technical SpeCifiGatlonS cs ica cacicestaaacavisosasacsnsacessaneeassacnsnnesenoeccrvessasaaavansesandeasesdenacesasuessannaueabeeaneeeneendeuneaceaaeaaes Meare 12 WAITAINY aa E tareael neal aaa uael anda Sade adh nn a ener inal aaa 13 DISC EAMIN OF Tercrio n n cen acta S A cicada A O A 13 Weight Capacity THE CEILING STRUCTURE MUST BE CAPABLE OF HOLDING FIVE Maximum flat panel weight 360lbs 5 TIMES THE WEIGHT OF THE FLAT PANEL AND MOUNT IF NOT THEN THE CEILING STRUCTURE MUST BE REINFORCED Warning Statements INSTALL THE MOUNT ACCORDING TO THE INSTRUCTIONS PROVIDED BY PREMIER MOUNTS PERFORM ALL STRUCTURAL REINFORCEMENTS BEFORE ATTACHING THE FLAT PANEL TO THE CEILING MOUNT USE THE APPROPRIATE LIFTING
12. evere property damage or personal injury This product is intended for indoor use only Use of this product outdoors could lead to product failure and or serious personal injury Do not install near sources of high heat Do not install on a structure that is prone to vibration movement or chance of impact Contact Premier Mounts with any questions 800 368 9700 techsupport mounts com AN AN A AN AN A Page 2 Installation Instructions ECM 3763Q Installation Tools The following tools may be required dependent upon your particular installation These tools are not provided by Premier Mounts but you can purchase them at your local hardware store Screwdriver Pencil g Tape Measure Protective Eye Wear 10mm Wrench Ladder Parts List Your Premier Mounts product is shipped with all proper installation hardware and components Make sure that none of these parts are missing and or damaged before beginning installation If there are parts missing and or damaged please stop the installation and contact Premier Mounts 800 368 9700 ECM 3763Q Mount Hardware Elliptical Tilt Mount Qty 4 TuT AT Decorative Covers Qty 8 Mounting Bracket Arms Qty 8 TITT FEET M4 x 8mm Phillips Screws Qty 8 M6 x 25mm Phillips Screws Qty 8 Thread Depth Indicator Qty 1 Allen Wrench Qty 1
13. ll straw or toothpick into the threaded inserts found on the back of the flat panel Use a pencil to mark the depth of the threaded insert on the small straw or toothpick Mark the straw or toothpick 1 8 above the depth of the threaded insert as shown in Figure 1 Insert the small straw or toothpick into the remaining threaded inserts to compare and verify their depth using the straw or toothpick s 1 8 allowance mark Locate the correct diameter screw for the threaded insert Marking the 1 8 Allowance If the screw you selected is longer than the 1 8 allowance mark on the small straw or toothpick Marking the Depth as shown in Figure 2 and Figure 3 do not use this screw The screw length must not bypass the mark Threaded Insert V Small Straw or Toothpick lt The correct screws should thread easily into the mounting point and not pull out when tension is applied The optional M3 flat washers may be used to decrease the screw depth of either the M2 5 x 12mm screws or the M3 x 16mm screws Decrease the screw depth by placing an M3 flat washer inside the leveling barrel and then inserting the mounting or Toothpick By or Toothpick screw Test each size of the screws provided Installation Instructions Page 7 ECM 3763Q Griplate Washer Installation Premier Mounts Griplate Washers are designed to accommodate the various M4 M5 M6 and M8 hole sizes require
14. n Instructions Page 9 gt 4 22 ECM 3763Q Attaching the Flat Panel Install the mount according to the instructions provided by Premier Mounts Ensure all structural reinforcements have been made before attaching the flat panel to the ECM 3763Q Do not release the flat panel until the mounting bracket arms are fully resting on the elliptical mounting bar Raise the mounting bracket arms and the attached flat panel over the elliptical mounting bar of the ECM 3763Q Figure 1 Mounting Bracket Arms Elliptical Mounting Bar AST 2446 ceiling adapter shown for illustration purposes only Lower and center the mounting bracket arms with the attached flat panel onto the elliptical mounting bar of the ECM 3763Q i Repeat Steps 1 and 2 for mounting the remaining elliptical tilt mounts Do not release the flat panel until the mounting bracket arms are resting fully on the elliptical mounting bar Displays should be installed opposite of each other to even out the weight Figure 3 Proceed to Attaching the Decorative Covers section 2nd Top view of ECM 3763Q with flat panels Figure 3 Figure 2 AST 2446 ceiling adapter shown for illustration purposes only Page 10 Installation Instructions ECM 3763Q Attaching Decorative Covers When attaching the decorative covers verify the direction of the covers The smaller mounting hole should be in position
Download Pdf Manuals
Related Search