AMX MB-TP15
Contents
1. 2 These screws secure the back box to the internal panel casing DO NOT DO NOT REMOVE REMOVE these these panel panel securing securing screws screws Unscrew these 4 pan head Housing screws to remove the back box FIG 2 Location of the attachment screws on the NXD back box 7 Lift the back box housing to separate it from the internal panel casing Note Do not remove the four panel securing screws These screws secure the LCD to the metal casing Installing the MB TP15 Back Box 1 Unscrew the four pan head Housing screws 8 32 from the MB TP15 rear plastic cover 2 Gently place the MB TP15 back box over the internal panel casing with the cable routing hole on the right side of the panel 3 Re install and secure the four pan head Housing screws into their pre drilled holes along the edges of the MB TP15 back box FIG 2 and secure them using a grounded Phillips head screwdriver 4 Replace the Connector Overlay back over the connector opening and align the connector locations 5 Re secure the metal connector overlay using a grounded Phillips head screwdriver and re secure the nut on the headphone jack Cable Installation for the MB TP15 Back Box 1 Connect the cable connectors RJ 45 Ethernet and any other audio video wiring to their respective locations on the side of the touch panel 2 Use the tie wrap 45 0009A to wrap the cables together inside the VESA Mount enclosure This ca2. 009A for use with NXA MTC RGB Twelve Under cut Phillips head screws 6 32 x 0 500 Black 80 0139 Strain relief grommet 45 0004 03 for use with CA2250 50 Universal VESA Msount grommet 45 0032 01 for use with NXA MTC RGB Overview Installing the MB TP15 Kit Upgrading the original Modero back box with the MB TP15 Universal VESA Mounting Kit involves three main processes e Removing the original Modero back box and installing the new MB TP15 back box e Threading cables through the strain relief grommet opening in the rear plastic cover e Finalizing the installation of the NXD with MB TP15 back box and cables into the plastic cover securing both components and finalizing the strain relief grommet installation Removing the Original Modero Back Box 1 Detach all connectors from the side of the touch panel 2 Remove the magnetic faceplate from the NXD unit by carefully grip ping the faceplate and pulling outwards 3 Place the LCD face down on a soft cloth to expose the bottom of the panel and prevent scratching of the LCD 4 Using a grounded Phillips head screwdriver remove the two screws on either side of the metal connector overlay and remove the head phone nut from the headphone jack Quick Start Guide MB TP15 Universal VESA Mounting Box for 15 Modero Panels 5 Remove the Connector Overlay from the back box housing 6 Remove the four pan head housing screws from the rear of the NXD unit FIG
3. BPE IT S YOUR WORLD TAKE CONTROL The MB TP15 Universal VESA Mounting Kit FG032 50 allows the 15 Modero touch panels to be mounted on a pivot pitch extendable arm pole ceiling under cabinet mount or any other variation of VESA compliant mounting hardware The MB TP15 kit includes everything the installer needs to mount a 15 Modero panel wall mount version to any standard 75mm x 75mm VESA mounting hardware purchased separately The kit includes a metal back box a plastic rear cover with cable routing hole which accepts the included strain relief grommet and other required hardware see Specifications table for details front CE wee Cable routing hole accepts Strain Relief Grommet al a I J p A A 75mm x 75mm VESA mounting configuration FIG 1 MB TP15 Universal VESA Mounting Box and Rear Cover rear view Specifications MB TP15 Specifications MB TP15 Mounting Kit Installed Dimensions e 14 37 x 15 19 x 3 59 36 50 cm x 38 59 cm x 9 12 cm HWD Operating Storage Environments Operating Temperature 0 C 32 F to 40 C 104 F Operating Humidity 20 85 RH Storage Temperature 20 C 4 F to 60 C 140 F Storage Humidity 5 85 RH Included Accessories Black metallic VESA back box 62 0032 50 Black plastic cover with grommet opening 60 0032 50 Four Phillips pan head screws 8 32 x 0 50 Black 80 0146 02 Tie Wrap Large 45 0
4. NXD panel with LCD MB TP15 back box and attached cables rotate the entire unit over and lie it on a flat level surface 7 Note the available mounting contact surface area on the rear plastic cover FIG 3 This area represents the space available for use with a VESA connector plate 8 Insert and secure the twelve 6 32 securing screws into their pre drilled holes along the edges of the NXD unit FIG 4 This step secures the NXD unit to the rim of the rear plastic cover 9 Align a VESA mount connector purchased separately to the four 8 32 screw holes on the back of the rear plastic cover FIG 4 10 Insert the four provided 8 32 screws through the VESA mount s four holes and then into the pre drilled holes on the rear plastic cover Note When installing a VESA mount to the rear plastic cover use only the AMX provided 8 32 screws Ai DO NOT REMOVE me se 6 32 securing gt Securing hole locations 3 on each side 4 11 Secure these four 8 32 screws to the rear plastic cover by using a grounded Phillips head screwdriver This step secures the VESA mount to the rear of the panel Refer to your particular VESA mount manufacturer s installation procedures for further surface mounting procedures 72 18MM 3 83 97MM 4 52 1 15MM FIG 3 MB TP15 Mounting contact surface area K MB TP15 back box Bek 62 0032 50 3 23 82MM Strain relief grommet C
5. ble tie is used to insure the cable will not pull through or work itself through the new larger strain relief grommet 45 0032 01 over time 3 Thread the incoming cables through the hole on the rear plastic cover and then through the strain relief grommet Slide the grommet along the cable and securely insert it into the opening on the rear plastic cover FIG 4 a Finalizing the Installation 1 Gently place the rear plastic cover over the NXD panel with LCD and MB TP15 back box 2 Insert the protruding cables coming out from the opening on the rear plastic cover into the open strain relief grommet 3 Allow some slack length on these cables as a service loop This ser vice loop provides enough cable length so you can later remove the NXD with connected cables from the rear plastic cover Caution Verify that the Strain Relief Grommet is securely closed over the cables and the clip is facing the correct direction upwards The process of securing the strain relief grommet may require the use of pliers Also verify the length and location of the inserted cables once the strain relief grommet is closed it is difficult to re open 4 Carefully apply pressure to close the strain relief grommet over the desired cable location 5 Firmly push the strain relief grommet into the opening toward the inside until the rim is securely flush against the back of the rear plas tic cover FIG 4 6 Securely grasp both sides of the
6. lip facing up Rim of the strain relief grommet should lie flush against enclosure Four pan head Housing Screws Rear plastic cover 60 0032 50 FIG 4 Location of the attachment screws on the NXD back box AMX Corporation reserves the right to alter specifications without notice at any time For full warranty information refer to the AMX Instruction Manual s associated with your Product s 036 004 2785 12 05 2005 AMX Corporation All rights reserved The AMX logo is a trademark of AMX Corporation AMX reserves the right to alter specifications without notice at any time 3000 RESEARCH DRIVE RICHARDSON TX 75082 800 222 0193 fax 469 624 7153 technical support 800 932 6993 e www amx com Route cabling through the Strain Relief Grommet Four 8 32 screws 93 0032 50 REV C ATR
Download Pdf Manuals
Related Search