Da-Lite Contour Electrol 130"
Contents
1. Instruction Book for COUNTOUR ELECTROL DA LITE IMPORTANT SAFETY INSTRUCTIONS 1 Read and understand all instructions before using 2 Position the cord so that it will not be tripped over pulled or contact hot surfaces 3 If an extension cord is necessary a cord with a current rating at least equal to that of the appliance should be used Cords rated for less amperage than the appliance may overheat When using your video equipment basic safety precautions should always be followed including the following 4 To reduce the risk of electric shock do not disassemble this appliance Contact an authorized service dealer when repair work is required Incorrect reassembly can cause electric shock when the appliance is used subsequently 5 The use of an accessory attachment not recommended by the manufacturer may cause a risk of fire electric shock or injury to persons TOOLS REQUIRED FOR INSTALLATION 2 Phillips Screwdriver PRE INSTALLATION 1 Carefully unpack screen and remove outer wrapping from case INSTALLATION 2 Set aside the Installation Kit Items inside will be used during installation NOTE Remove the black tape and rubber bands from the slat bar after the case has been installed There are three ways to install the Contour Electrol Wall Mount Ceiling Mount or Ceiling Hook Procedures for each method are as follows WALL MOUNT 1 Using a 2 Phillips2. CONTOUR ELECTROL INSTALLATION FOR 120V SCREENS 120V WIRING DIAGRAM 3 conductor 20 24 gauge wire can be used in place of the supplied RJ 14 cable to connect the wall switch Connect the BUS terminals on the wall switch to the corresponding BUS terminals on the splitter board Up Limit Tactile Button Down Limit Tactile Button Front of Back of Wall Switch Wall Switch RJ 22 Jack Connection to Wall Switch atio eo To view a video of this installation visit http youtu be t2ZO9PVAhEg or use the OR code below g ORO Fa RJ 14 Pin Outs Tab Is Facing Up Bus RP Data White RO Data Green 5V 60 Ground Black Supplied RJ 14 cable IMPORTANT NOTE The wall switch is REQUIRED to make any limit switch adjustments EVEN if a third party control system is used Therefore it is advised to wire the switch or provide a 3 conductor connection that is accessible LED RJ 22 Output RJ 45 Jack Wire White Common Black Power Input 120VAC 60Hz RJ 22 Pin Outs Tab Is Facing Up 12V Blue Bus RP Data Yellow RO Data Green 5V L Red Ground Black RQ Clock White Standard RJ 22 can be used in place of RJ 14 cable Data R Cable Green Ground Ground Must be Connected to Hot Building Ground Up Dry Contact Down Dry Contact Common Both Bus Bus 5V Bus
3. Locate the two tactile buttons on the back of the switch They are black round buttons on silver plates See 120V Wiring Diagram To adjust the down limit switch press and hold the down tactile button until the LED on the back of the switch turns solid red This will put the motor in limit set mode Turn the wall switch over and use the down button on the front of the switch Press and hold the down button until the desired down position is reached If you travel too far down press the up button to move the screen upward If you press and let go of either the up or down buttons the motor will do a small jog in that direction for fine adjustment of the screen Once the desired position is reached turn the switch over press and hold the down tactile button until the LED on back of switch blinks red twice The down limit is now set NOTE If the screen is in limit set mode and no buttons are pushed for 20 seconds the LED on the back of the wall switch will turn off the motor will return to run mode and no changes will be saved If this occurs return to step 3 for down limit adjustment or step 4 for up limit adjustment 4 To adjust the up limit switch press and hold the up tactile button until the LED on the back of the switch turns solid green This will put the motor in limit set mode Turn the wall switch over and use the up button on the front of the switch Press and hold the up button until the desired up position is reached
4. MERCHANT ABILITY Any implied warranties of fitness for use or merchantability that may be mandated by statute or rule of law are limited to the five 5 year warranty period This warranty gives you specific legal rights and you may also have other rights which vary from state to state NO LIABILITY IS ASSUMED FOR EXPENSES OR DAMAGES RESULTING FROM INTERRUPTION IN OPERATION OF EQUIPMENT OR FOR INCIDENTAL DIRECT OR CONSEQUENTIAL DAMAGES OF ANY NATURE In the event that there is a defect in materials or workmanship of a Da Lite product you may contact our Sales Partners at PO Box 137 Warsaw IN 46581 0137 574 267 8101 800 622 3737 IMPORTANT THIS WARRANTY SHALL NOT BE VALID AND DA LITE SHALL NOT BE BOUND BY THIS WARRANTY IF THE PRODUCT IS NOT OPERATED IN ACCORDANCE WITH DA LITE S WRITTEN INSTRUCTIONS Keep your sales receipt to prove the date of purchase and your original ownership an A Milestone AV Technologies Brand 3100 North Detroit Street Post Office Box 137 Warsaw Indiana 46581 0137 P 574 2678101 or 800 622 3737 F 574 267 7804 or 877 325 4832 E info da lite com www da lite com DL 0114 12 12 2012 Da Lite Screen Company LLC Printed in U S A 88819
5. rewire incoming electric line Replace fuse Reset circuit breaker Check above Tighten all loose wire connections Correct any improper connections Down Position Check for power across black and white leads Up Position Check for power across red and white leads Screen will not operate and motor does not hum Power at junction box Thermal overload tripped Broken wire in the down or up position Defective motor limit switch or capacitor Capacitor burned out Let motor cool down for 15 minutes Try again Check for continuity Cut off old splice and reconnect Replace motor assembly NOTE Motor is a sealed assembly Replace motor assembly Incorrect stopping position in downward direction Lost roller wrap r Down limit switch out of adjustment See instructions below See installation instructions Incorrect stopping position in upward direction Lost roller wrap Up limit switch out of adjustment See instructions below Adjust up limit switch Call for information Noise NOTE Screen will operate with a low pitched hum Squeaking rubber end plug rubbing on motor Grinding Foreign object in screen rubbing on roller or fabric Gear noise Center roller in case Remove Replace motor assembly Coasting Defective brake Replace motor assembly RESTORING LOST ROLLER WRAP 1 2
6. 3 4 Remove tape and strap Tape a strap to the bottom of the screen surface Push strap over back of roller Feed fabric as you pull strap to draw fabric over top of roller 10 11 LIMITED FIVE YEAR WARRANTY ON DA LITE CONTOUR ELECTROL PRODUCTS ONLY Da Lite Screen Company LLC warrants these products to the original purchaser only to be free from defects in materials and workmanship for a period of five 5 years from the date of purchase by the original purchaser provided they are properly operated according to Da Lite s instructions and are not damaged due to improper handling or treatment after shipment from the factory This warranty does not apply to equipment showing evidence of misuse abuse or accidental damage or which has been tampered with or repaired by a person other than authorized Da Lite personnel Da Lite s sole obligation under this warranty shall be to repair or to replace at Da Lite s option the defective part of the merchandise Returns for service should be made to your Da Lite dealer If it is necessary for the dealer to return the screen or part to Da Lite transportation expenses to and from Da Lite are payable by the purchaser and Da Lite is not responsible for damage in shipment To protect yourself against damage or loss in transit insure the product and prepay all transportation expenses THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING WARRANTIES AS TO FITNESS FOR USE AND
7. If you travel too far up press the down button to move the screen downward If you press and let go of either the up or down buttons the motor will do a small jog in that direction for fine adjustment of the screen Once the desired position is reached turn the switch over press and hold the up tactile button until the LED on back of switch blinks green twice The up limit is now set To test the limit switch settings press and release the up or down buttons on the switch to operate the screen Replace the switch and cover plate on the wall IMPORTANT NOTE The wall switch is REQUIRED to make any limit switch adjustments even if a third party control system is used Therefore it is advised to wire the switch or provide a 3 conductor connection that is accessible CAUTION Do not adjust for more drop than what was ordered At least 1 1 2 wraps of fabric must remain on the roller This screen comes standard with 0 or 2 black at the top See the specification data sheet for details SCREEN ADJUSTMENT FOR 220V 240V SCREENS WITH A BUILT IN LOW VOLTAGE CONTROL 1 4 N Remove the cover plate from the 3 button wall switch and remove the switch from the junction box Locate small 3 position switch on back of wall switch See Figure 11 To adjust the down limit switch slide the 3 position switch to the down position Press and hold the down button to run the screen down to the desired stop position Release the but
8. Receptacle RJ 45 Pin Outs Tab Is Facing Up Manual 2 Brown 12V Blue Bus RP Data Yellow a RO Data Green 5V Red Ground Black I RO Clock Orange Manual 1 Purple CONTOUR ELECTROL INSTALLATION FOR 120V SCREENS 120V WIRING DIAGRAM WITH OPTIONAL BUILT IN VIDEO PROJECTOR INTERFACE CAUTION The projector must be turned off before connecting IMPORTANT NOTE The wall switch is REQUIRED to make the trigger wires to the projector Failure to do so may damage any limit switch adjustments EVEN if a third party control the controller system is used Therefore it is advised to wire the switch or rovide a 3 conductor connection that is accessible Use 2 conductor 20 24 gauge wire to extend the low voltage p connection from the projector s 5 or 12 volt screen trigger 3 conductor 20 24 gauge wire can be used in place of the output to the length required to reach the VPI When extending supplied RJ 14 cable to connect the wall switch Connect the the low voltage connection from the projector s screen trigger BUS terminals on the wall switch to the corresponding BUS output polarity does not matter The red and black wires from terminals on the splitter board the VPI are interchangeable Up Dry Contact Down Dry Contact Common Both Bus Bus 5V Bus LED RJ 22 Output RJ 22 Inputs Front of Back of Wall Switch Wall Switch Receptacl
9. e RJ 22 Jack Connection to Wall Switch RJ 45 Jack Data Hoz Cable VPI Trigger Module White Green Ground Common Ground Must be Connected to Black Hot Building Ground Power Input 120VAC 60Hz 5 12 Volt Screen Trigger on Projector CONTOUR ELECTROL INSTALLATION FOR 240V SCREENS 240V WIRING DIAGRAM ILT RJ 9 Pin Outs Tab Is Facing Up IMPORTANT NOTE The wall switch is REQUIRED to make any limit switch adjustments EVEN if a third party control Black e system is used Therefore it is advised to wire the switch or Ground Common Red provide a 4 conductor connection that is accessible 5V Green Data or Down White Blue Common BA BA Power Input Brown Hot UP UPD GND 240VAC 50Hz Green 5V STOP Green Ground to Case 3 POSITION DOWN SWITCH RJ9 NOTE Ground Must be gt Connected to Building Ground 5238 E 4 OOOO Splitter Front of Wall Back of Dry Contacts Switch Wall Switch 240V WIRING DIAGRAM WITH OPTIONAL BUILT IN VIDEO PROJECTOR INTERFACE A CAUTION THE PROJECTOR MUST BE TURNED OFF 2 Connect the wires from the VPI that are labeled Low BEFORE CONNECTING THE TRIGGER WIRES TO THE Voltage Connection to the end of the extended screen PROJECTOR FAILURE TO DO SO MAY DAMAGE THE trigger wires above CONTROLLER IMPORTANT NOTE The
10. n case has two channels with threaded nuts that slide the length of the case Attach the two ceiling hook mount brackets using the 1 4 x 5 8 screws and threaded nuts two per bracket The brackets can be attached anywhere within 12 of the ends of the case Figure 4 1 4 X 5 8 Flat Head Screw 4 Before hanging your Contour Electrol be sure the ceiling has adequate reinforcement 5 Using the holes in the ceiling hook brackets hang the Contour Electrol using the appropriate hardware and fasteners for your ceiling type Figure 4 ELECTRICAL INSTALLATION 1 Open the junction box on the left end of the case using a 2 Phillips screwdriver Install electrical connections that apply to your unit Make sure to review the wiring diagram for proper hook up Replace the junction box cover NOTE Must be installed in accordance with the requirements of the Local Building Codes the Canadian Electrical Code CEC CAN CSA C22 1 and the National Electric Code NEC NFPA 70 2 Test installation by running screen up and down a few times Be prepared to stop screen should any objects obstruct the movement of the screen To prevent damage to the motor the standard duty cycle is 1 minute on and 3 minutes off Junction Box Cover Figure 5 SCREEN ADJUSTMENT FOR 120V SCREENS 1 2 3 Locate the wall switch and remove the cover plate from the wall switch and remove the switch from the junction box
11. screwdriver loosen the two stop screws and remove the wall mount bracket from the back side of the case Figure 1 NOTE The ceiling flush mount and ceiling hook mount brackets are attached to the top side of the case These brackets are not necessary for wall mounting and can be removed at this time 2 Secure the wall mount bracket to the wall at the desired height The wall mount bracket should be fastened to the wall studs or some reinforcement within the wall Concrete or brick walls require special fasteners and anchors Allow at least 2 3 8 above the wall mount bracket to be able to position the case on the bracket Figure 2 lt lt 5 11 16 gt E we 275 16 2 9 16 Case Hook 6 3 8 1 Wall Mount Bracket U Stop Screws Slat Bar Figure 1 INSTALLATION continued 3 Make sure the bracket is level 4 Hang the screen case on the wall mount bracket as shown Va in Figure 2 Be sure the case is fully seated on the bracket O 5 Tighten the two stop screws against the wall mount bracket Wall gt using a 2 Phillips screwdriver Figure 1 CEILING FLUSH MOUNT 1 The ceiling hook brackets are attached to the top side of the nA housing They must be removed prior to ceiling flush mount NOTE Do not remove the wall mo
12. ton to stop the screen DO NOT PUSH THE STOP BUTTON When the screen is in the desired down position slide the 3 position switch to the off center position The down limit switch is now set To adjust the up limit switch slide the 3 position switch to the up position Press and hold the up button to run the screen up to the desired stop position Release the button to stop the screen DO NOT PUSH THE STOP BUTTON When the screen is in the desired up position slide the 3 position switch to the off center position The up limit switch is now set To test limit switch setting make sure the 3 position switch A is in the off center position Press and release the up or down button on the wall switch to operate the screen Replace switch and cover plate on the wall NOTE If stop button is pressed the wall switch will reverse direction To correct this press the stop button again This will reset the switch You will have to re set both the up and the down settings IMPORTANT NOTE The wall switch is REQUIRED to make any limit switch adjustments EVEN if a third party control system is used Therefore it is advised to wire the switch or provide a 4 conductor connection that is accessible CAUTION Do not adjust for more drop than what was ordered At least 1 1 2 wraps of fabric must remain on the roller This screen comes standard with 0 or 2 black at the top See the specification data sheet for details
13. unt bracket even if you ee are not using it for mounting This provides structural n Bracket stability to the case 9 1 2 Using a 2 Phillips screwdriver loosen the four 1 4 5 8 A screws holding the ceiling flush mount brackets Figure 3 3 Slide the ceiling flush mount brackets so that the mounting holes extend beyond the ends of the case All four 1 4 x 5 8 screws must remain within the channels Figure 2 4 Tighten the four 1 4 x 5 8 screws holding the ceiling flush mount brackets Figure 3 5 Before mounting your Contour Electrol be sure the ceiling has adequate reinforcement 1 4 X 5 8 Flat Head Screw 6 Hold the screen case up to the ceiling and mark the hole locations The brackets have a set of front holes and a set of rear holes Attach the Contour Electrol using the appropriate hardware for your ceiling type It is best to use at least one hole in each set CEILING HOOK MOUNT 1 The ceiling hook mount brackets are tied together and attached to the ceiling flush mount bracket at one end of the case Remove the ceiling hook mount brackets en Figure 3 2 Remove the ceiling flush mount brackets using a 2 Phillips screwdriver Figure 3 Retain four 1 4 x 5 8 screws Note Do not remove the wall mount bracket even if you are not using it for mounting This provides structural stability to the case Ceiling Hook Bracket 3 The top of the scree
14. wall switch is REQUIRED to make 1 Use 2 conductor 20 24 gauge wire to extend the low voltage any limit switch adjustments EVEN if a third party control connection from the projector s 5 or 12 volt screen trigger system is used Therefore it is advised to wire the switch or output to the length required to reach the VPI When provide a 4 conductor connection that is accessible extending the low voltage connection from the projector s screen trigger output be sure to maintain the proper polarity The red wire from the VPI is the signal and the black wire from the VPI is the ground Brown Hot 240VAC 50Hz Power Source Green Yellow as Ground Green Yellow Ground Brown Down Blue Common Black Up Blue Common Front of Wall Back of Switch Wall Switch 5 12 Volt Screen Trigger on Projector TROUBLESHOOTING Visit www da lite com products tutorials php to find installation and troubleshooting tutorials You will also find a link to Live Chat for interactive support Symptom You can contact us by email at info da lite com or by phone at 800 622 3737 or 574 267 8101 with any additional troubleshooting questions Cause Solution Screen will not operate and motor does not hum Incorrect line voltage Blown fuse Tripped circuit breaker No power to operating switch or junction Verify 115 125V or 220 240V If insufficient voltage
Download Pdf Manuals
Related Search