Rosewill RC-215 RAID controller
Contents
1. and rebuild Continue to boot Select Choose replacement drive and rebuild press Enter Select the replacement drive then press Enter When asked WARNING Would you like to Continue Press Y N press Y to accept The set will be rebuilt The status of the rebuild is displayed in the menu When rebuild is completed a Enter the VIA RAID Utility after exiting Y N message will pop up inform you that rebuild is finished press N to reboot system RAID 0 1 Mirroring Striping This RAID array to be used on New Blank hard drives do not use existing hard drive s with data To create a RAID 0 1 set four hard drives are required Auto configuration recommended SATA105G ATA 133 RAID Controller Card RC215 User Manual i The default chunk size is 64k when selecting Auto configuration As the BIOS boots press Tab when prompted to enter the RAID BIOS At the RAID utility main menu select Create Array press Enter At the next screen select Auto Setup Safe Performance press Enter When asked Auto Create array will destroy all data on disks Continue Y N press Y to accept And then a Create New Raid Success Message will be displayed Press ESC to quit then go back to the RAID utility main menu Press ESC to exit the BIOS When asked Do you really want to exit the utility Y N press Y to accept Manual configuration As the BIOS boots press Tab when prompted to enter the RAID BIOS At RAID utility main menu sele2. to exit the BIOS When asked Do you really want to exit the utility Y N press Y to accept For Existing Hard Drives with Data As the BIOS boots press Tab when prompted to enter the RAID BIOS At the RAID utility main menu select Create Array press Enter At the next screen select Array Mode RAID 1 Mirroring press Enter At the next screen select RAID 1 for data protection press Enter At the next screen select Select Disk Drives press Enter Please use arrow keys fand to select the Source drive press Enter Please use arrow keys fand to select the Mirror Target drive press Enter Select Start Create Process press Enter When asked Save the data on source disk to mirror after creation Y N press Y to accept The set will be built The status of the built is displayed in the menu When build is completed a Create New Raid Success Message will pop up inform you that build is finished SATA105G ATA 133 RAID Controller Card RC215 User Manual a Rebuild Mirror Drive When a failure to one member occurs you will be notified by the RAID BIOS during boot The steps below will guide you in rebuilding a failed mirror set Replace he failed drive s with one of equal or greater capacity then start the computer Then you will see the following message shown by the PCI SATA PATA RAID card s BIOS on the screen Power off and check the failed drive Destory the Mirroring Relationship Choose replacement drive
3. Prosewill i SATA1 5G ATA133 RAID Controller Card RC215 User Manual O SATA105G ATA 133 RAID Controller Card RC215 User Manual Features and Benefits e Compliant with Serial ATA 1 0 specification e Compliant with PCI Specification revision 2 2 Provides three independent channels to connect two SATA and one PATA hard disk drive Supports up to UDMA6 transfer mode of PATA Supports up to 4 storage device connection Supports RAID 0 1 0 1 and JBOD functions Supports drives with capacities larger than 137GB Supports Windows 2000 XP 2003 32 64 bit Vista 32 64 bit Important Message for User before Installing RC 215 Windows Device Manager can NOT recognize the hard drives that without correct RAID setting before The working data on your existing HDD may NOT work when you migrate it to RAID Host Card Raid sets can be created and managed by the BIOS utility setting For RAID creating BIOS utility allow the random creating The Rebuilding function on Raid 1 or Raid 10 may spend long hours for component ready and function available please be patient for that Raid 0 and Raid1 need at least 2 drives and Raid10 need 4 drives 1 Backup all your data in HD before setting any RAID Setting RAID 0 0 1 will destroy all original data of your HD 2 New HD connecting to RC 215 must process initial F disk and format before using Otherwise PC might find nothing in the system 3 If you want to boot from c
4. V2003 then press Enter Press Enter to finish driver installation then follow the on screen instructions to complete the Windows installation For An Existing Installation Setup the RAID Array prior to driver installation and boot up to Windows At the Found New Hardware Wizard window pop up please click Cancel button to cancel the driver installation for the device at this moment The driver for this device will be installed in the next step Please insert the CD driver bound with PCI SATA PATA RAID card into your CD ROM Drive At the Windows desktop click Start then Run 11 SATA105G ATA 133 RAID Controller Card RC215 User Manual a Type D RC 212 SETUP EXE click OK Change D to match your CD ROM drive letter Follow the on screen instructions to complete the installation Restart Windows to complete the installation For Windows XP x64 Server 2003 x64 For New Installation A new installation requires a floppy disk for the driver installation To make this floppy disk copy the contents of the RC 212 VRAIDDrv drvdisk folder found on the driver CD onto a blank floppy disk then follow the directions below Setup the RAID Array prior to Windows installation Follow Microsoft s Windows installation procedure Restart the computer when prompted by Windows installation At the Windows Setup screen press F6 to install the RAID driver When prompted press S to specify the location of the driver Inser
5. ccept Manual configuration As the BIOS boots press Tab when prompted to enter the RAID BIOS At the RAID utility main menu select Create Array press Enter At the next screen select Array Mode RAID 1 Mirroring press Enter At the next screen select RAID 0 for performance press Enter At the next screen select Select Disk Drives press Enter Please use arrow keys fand to switch the disk then press Enter to mark the selected disk Select Block Size 64 press Enter Select chunk size from 4K 8K 16K 32K or 64K then press Enter Select Start Create Process press Enter When asked The data on the selected disk will be destroied Continue Y N press Y to accept And then a Create New Raid Success Message will be displayed Press ESC to quit then go back to the RAID utility main menu Press ESC to exit the BIOS When asked Do you really want to exit the utility Y N press Y to accept SATA105G ATA 133 RAID Controller Card RC215 User Manual RAID 1 Mirroring For New Blank Hard Drives As the BIOS boots press Tab when prompted to enter the RAID BIOS At the RAID utility main menu select Create Array press Enter At the next screen select Auto Setup For Data Security press Enter When asked Auto Create array will destroy all data on disks Continue Y N press Y to accept And then a Create New Raid Success Message will be displayed Press ESC to quit then go back to the RAID utility main menu Press ESC
6. ct Create Array press Enter At the next screen select Array Mode RAID 1 Mirroring press Enter At the next screen select RAID 0 1 press Enter At the next screen select Select Disk Drives press Enter Please use arrow keys fand to select the first drive press Enter Please use arrow keys fand to select the second drive press Enter Please use arrow keys fand to select the third drive press Enter Please use arrow keys fand to select the fourth drive press Enter Select Block Size 64 press Enter Select chunk size from 4K 8K 16K 32K or 64K then press Enter Select Start Create Process press Enter When asked The data on the selected disk will be destroied Continue Y N press Y to accept And then a Create New Raid Success Message will be displayed Press ESC to quit then go back to the RAID utility main menu 8 SATA105G ATA 133 RAID Controller Card RC215 User Manual Press ESC to exit the BIOS When asked Do you really want to exit the utility Y N press Y to accept SPAN JBOD As the BIOS boots press Tab when prompted to enter the RAID BIOS At the RAID utility main menu select Create Array press Enter At the next screen select Auto Setup For Capacity press Enter When asked Auto Create array will destroy all data on disks Continue Y N press Y to accept And then a Create New Raid Success Message will be displayed Press ESC to quit then go back to the RAID utility main menu Pre
7. firmly Attach your internal or external devices to the PC SATA PATA RAID card Replace the slot bracket s holding screw to secure the card Replace the computer cover and reconnect the power cord RAID Arrays RAID Arrays are setup in the PCI SATA PATA RAID card s BIOS There are four configurations supported RAID level Type Configurations Number of disks needed RAID 0 Disk Striping 2or3or4 RAID 1 Disk Mirroring 2 RAID 0 1 Disk Striping 4 Mirroring JBOD Disk Concatenation 2or3or4 RAID 0 Striping This RAID array to be used on New Blank hard drives Striping will destroy existing data on the hard drive Auto Configuration is recommended For applications that require custom chunk size Manual Configuration is offered Auto configuration recommended The default chunk size is 64k when selecting Auto configuration SATA105G ATA 133 RAID Controller Card RC215 User Manual As the BIOS boots press Tab when prompted to enter the RAID BIOS At the RAID utility main menu select Create Array press Enter At the next screen select Auto Setup For Performance press Enter When asked Auto Create array will destroy all data on disks Continue Y N press Y to accept And then a Create New Raid Success Message will be displayed Press ESC to quit then go back to the RAID utility main menu Press ESC to exit the BIOS When asked Do you really want to exit the utility Y N press Y to a
8. he RAID driver Insert the floppy disk please select VIA V1T6421 RAID Controller A VISTA x86 viamraid inf then press Next Change A to match your floppy drive letter Follow the on screen instructions to complete the Windows installation For An Existing Installation Setup the RAID Array prior to driver installation and boot up to Windows At the Found New Hardware Wizard window pop up please click Cancel button to cancel the driver installation for the device at this moment The 13 SATA105G ATA 133 RAID Controller Card RC215 User Manual driver for this device will be installed in the next step Please insert the CD driver bound with PCI SATA PATA RAID card into your CD ROM Drive At the Windows desktop click Start then Run Type D RC 212 SETUP EXE click OK Change D to match your CD ROM drive letter Follow the on screen instructions to complete the installation Restart Windows to complete the installation For Windows Vista x64 For New Installation A new installation requires a floppy disk for the driver installation To make this floppy disk copy the contents of the RC 212 VRAIDDrv drvdisk folder found on the driver CD onto a blank floppy disk then follow the directions below Setup the RAID Array prior to Windows installation Follow Microsoft s Windows installation procedure Restart the computer when prompted by Windows installation At the Windows Setup screen press Load Driver
9. orrect HD connecting to either motherboard or RC 215 please change correct HD source from CMOS booting sequence 4 Although SATA HD is a hot swap design it is strongly recommended 2 SATA105G ATA 133 RAID Controller Card RC215 User Manual that all users turn off the power before you add any HD to PC 5 If you want to use RC 215 without any RAID function please do not enter RAID BIOS and change the RAID setting RAID function will only be activate after you enter RAID BIOS and set a RAID set correctly Driver installation is the same for a RAID card whether you want to use a RAID function or not Never install a un RAID version driver to a RAID card even you want to use a RAID card without RAID function Bus Interface PCI Bus 32 bit Connectors 2 x internal SATA connectors 1 x PATA connector Package Contents 1x PCI SATA PATA Raid Card 1 x User Manual 1 x Driver CD Note Contents may vary depending on the market country System Requirements Pentium class computer with one available PCI slot Windows 2000 XP 2003 32 64 bit Vista 32 64 bit Hardware Installation Turn Off the power to your computer Unplug the power cord and remove your computer s cover SATA105G ATA 133 RAID Controller Card RC215 User Manual Remove the slot bracket from an available PCI slot To install the card carefully align the card s bus connector with the selected PCI slot on the motherboard Push the board down
10. roduct 15
11. ss ESC to exit the BIOS When asked Do you really want to exit the utility Y N press Y to accept Delete RAID Disk Drive As the BIOS boots press Tab when prompted to enter the RAID BIOS At the RAID utility main menu select Delete Array press Enter Please use arrow keys fand to select the RAID set then press Enter When asked The selected array will be destoried Are you sure Continue Press Y N press Y to confirm BIOS Configuration The PCI SATA PATA RAID card s BIOS will appear every time your system starts up During this POST process the BIOS will show up and indicate the devices attached to it Driver Installation SATA105G ATA 133 RAID Controller Card RC215 User Manual a For Windows 2000 For A New Installation A new installation requires a floppy disk for the driver installation To make this floppy disk copy the contents of the RC 212 VRAIDDrv drvdisk folder found on the driver CD onto a blank floppy disk then follow the directions below Setup the RAID Array prior to Windows installation Follow Windows 2000 installation procedure Restart the computer when prompted by the installation At the Windows 2000 Setup screen press F6 to install the RAID driver When prompted press S to specify the location of the driver Insert the floppy disk then press Enter Select VIA V RAID Controller Series Windows 2K then press Enter Press Enter again to finish driver installation then follo
12. t the floppy disk then press Enter Select VIA V RAID Controller Series Windows XP SRV2003 x64 then press Enter Press Enter to finish driver installation then follow the on screen instructions to complete the Windows installation For An Existing Installation Setup the RAID Array prior to driver installation and boot up to Windows At the Found New Hardware Wizard window pop up please click Cancel button to cancel the driver installation for the device at this moment The driver for this device will be installed in the next step 12 SATA105G ATA 133 RAID Controller Card RC215 User Manual Please insert the CD driver bound with PCI SATA PATA RAID card into your CD ROM Drive At the Windows desktop click Start then Run Type D RC 212 SETUP EXE click OK Change D to match your CD ROM drive letter Follow the on screen instructions to complete the installation Restart Windows to complete the installation For Windows Vista For New Installation A new installation requires a floppy disk for the driver installation To make this floppy disk copy the contents of the RC 212 VRAIDDrv drvdisk folder found on the driver CD onto a blank floppy disk then follow the directions below Setup the RAID Array prior to Windows installation Follow Microsoft s Windows installation procedure Restart the computer when prompted by Windows installation At the Windows Setup screen press Load Driver to install t
13. to install the RAID driver Insert the floppy disk please select VIA V1T6421 RAID Controller A VISTA x64 viamrx64 inf then press Next Change A to match your floppy drive letter Follow the on screen instructions to complete the Windows installation For An Existing Installation Setup the RAID Array prior to driver installation and boot up to Windows At the Found New Hardware Wizard window pop up please click Cancel 14 SATA105G ATA 133 RAID Controller Card RC215 User Manual ee button to cancel the driver installation for the device at this moment The driver for this device will be installed in the next step Please insert the CD driver bound with PCI SATA PATA RAID card into your CD ROM Drive At the Windows desktop click Start then Run Type D RC 212 SETUP EXE click OK Change D to match your CD ROM drive letter Follow the on screen instructions to complete the installation Restart Windows to complete the installation To Verify Windows Installation Right click My Computer and click Manage Select Device Manager Double click SCSI and RAID Controller then double click VIA VT6421 RAID Controller to display driver properties A message this device is working properly is displayed in the dialog box the driver has been correctly installed Thank you for purchasing a quality Rosewill Product Please register your product at www rosewill com for complete warranty information and future support for your p
14. w the on screen instructions to complete the Windows installation For An Existing Installation Setup the RAID Array prior to driver installation and boot up to Windows At the Found New Hardware Wizard window pop up please click Cancel button to cancel the driver installation for the device at this moment The driver for this device will be installed in the next step Please insert the CD driver bound with PCI SATA PATA RAID card into your CD ROM Drive At the Windows desktop click Start then Run Type D RC 212 SETUP EXE click OK Change D to match your CD ROM drive letter Follow the on screen instructions to complete the installation 10 SATA105G ATA 133 RAID Controller Card RC215 User Manual Restart Windows to complete the installation For Windows XP Server 2003 For New Installation A new installation requires a floppy disk for the driver installation To make this floppy disk copy the contents of the RC 212 VRAIDDrv drvdisk folder found on the driver CD onto a blank floppy disk then follow the directions below Setup the RAID Array prior to Windows installation Follow Microsoft s Windows installation procedure Restart the computer when prompted by Windows installation At the Windows Setup screen press F6 to install the RAID driver When prompted press S to specify the location of the driver Insert the floppy disk then press Enter Select VIA V RAID Controller Series Windows XP SR
Download Pdf Manuals
Related Search