Philips LivingColors Table lamp 70999/60/PH
Contents
1. Colour intensity saturation If you want to add more white to your current colour or make your colour intense saturated again you can easily change the colour intensity saturation Just press the colour wheel on the left more white or right more colour position If you keep pressing on the left position you will ultimately reach white Discovering your LivingColors Extended functionality Automatic Colour Change Mode You can also let your LivingColors change colours automatically You can even choose how fast you want it to go through the whole colour spectrum Sweep your finger clockwise around the colour wheel one full circle 360 and briefly press on I On to get into the Automatic Colour Change Mode The LivingColors will now start looping through the colours Change the speed of the Automatic Colour Change Mode stepwise 20 steps in total by sweeping the colour wheel clockwise to go faster or anticlockwise to go slower for 90 during the time that the Automatic Colour Change Mode is on While the Automatic Colour Change Mode is on you can also adjust the saturation and brightness of the colours To switch back to the one colour mode sweep your finger clockwise around the colour wheel and press 0 Off Alternatively you can switch lights off O and on I again N f 7 A fa N ko PHIL PS Favourite Buttons With your LivingColors you can store2. on the wireless network e g a wireless router Iry moving the light away from the router or follow below procedure Make sure that all Living Colors connected to the remote control are switched on otherwise they will not respond after this action For the round remote control with mechanical wheel simultaneously press the l button and Favourite 2 button for 5 seconds For the round remote control with touch control simultaneously press the l button and Scene 3 button for 5 seconds For the long oval remote control simultaneously press the O button and saturation up button for 5 seconds The LivingColors will show an orange and then a green light for second and then they revert to their previous setting White lights LivingWhites first blink once then rapidly blink twice and revert to previous setting PHILIPS PHILIPS ae _ Solution 3 Reset the remote control Open the remote control s battery compartment and press the RESET button for a few seconds e g with a paper clip Make sure that the batteries are in After this action you need to reconnect your LivingColors to the remote control
3. User Manual LivingColors Iris Getting started with your LivingColors Unpacking and Installing If you unpack a LivingColors the product is already linked to the remote control You only need to plug it into the power system put the batteries into the remote control and start the experience Step l Place your LivingColors in a selected location on a flat and stable surface and direct it towards the wall P y g the optimal distance is 50 cm Step 2 Plug your LivingColors into the power system Step 3 Insert the two AAA batteries by sliding open the battery compartment and as indicated on the back of the remote control Basic functionality Switch the LivingColors On or Off Your LivingColors can be switched On and Off by using the ep and 0 button on the remote control If you switch the LivingColors Off it will remember your last setting for the next time you use it Colour selection To let your LivingColors change to whatever colour you like simply rotate the colour wheel rotary wheel at the centre of the remote control until you have found the right colour If you rotate the wheel quickly the colours will change quickly If you rotate slowly the colours will change slowly and you can really fine tune them i z PHILIPS Dimming Increase or decrease the light intensity by pressing the colour wheel on the top and bottom position
4. ing one remote control Note You can only connect add other smartlink products to your remote control 50 products maximum If the logo is not on the packaging product the product cannot be added to the system For the LivingAmbiance luminaires please make sure that you connect both the coloured light top of the shade and white light at the foot or ceiling plate Disconnecting multiple Philips LivingColors optional If you connect another remote control to the same luminaire it will be automatically disconnected from the first remote control unless the two remotes were connected first see further Alternatively you can disconnect a remote control from a luminaire as follows Hold the remote control against the Philips logo on the lens of the product then press and hold the O button The product will flash 3 times Hold the O button until the LivingColors is switched off automatically The LivingColors is now disconnected Connecting additional Remote Controls You can control the same products with several remote controls This is convenient if for example you want to leave one remote control in the kitchen and another one in the living room Step l Always reset the additional remote control first Open its battery compartment and press the RESET button for a few seconds The LED indicator will blink once hidden underneath the intensity up symbol The remote control has now been reset Step 2 Hold the add
5. itional remote control close to your current remote the l buttons pointing at each other Press the I buttons simultaneously on both remotes while the LED indicators on the remote controls blink intermittently Vhen they stop blinking the two remotes are connected to the same network Step 3 You still need to connect the additional remote to the LivingColors If you have two round remotes you can do it easily by re peating the above action bring two remotes close then press on I until they stop blinking intermittently This action needs to be done directly after connection of the additional remote control The additional remote is now connected to the same lights as the first remote control What to do if your LivingColors is not responding properly Solution Perform LivingColors and battery check p Unplug your LivingColors from the power network plug it back in and check whether it reacts to the remote control 2 Remove and reinsert batteries The batteries should be correctly placed and inserted and Check if batteries are charged 3 If the remote control is still not working try replacing the batteries 4 If necessary connect the remote control to the LivingColors again same way as connecting multiple LivingColors to one remote control Solution 2 Perform a channel switch In rare cases problems with the connection between your LivingColors and the remote control could be caused by heavy traffic
6. your two favourite colours for easy recall To store your favourite colour first select it using the colour wheel and dimming colour intensity on the remote control Then press and hold one of the Favourite Buttons until the LED indicator hidden underneath the intensity up symbol blinks this will take 5 sec onds Your favourite colour is now stored under the Favourite Button or 2 that you have pressed Whenever you want to go back to your favourite colour just press one of the Favourite Buttons The LivingColors will now show your favourite colour You can also store a particular Automatic Colour Change Mode in this way How to use multiple LivingColors Connecting multiple Philips LivingColors If you have multiple LivingColors at home you can all use them with Just one remote control lo connect the different LivingColors to the same remote control follow the instructions below Hold the remote control close against the Philips logo on the lens of the product then press and hold the I button The product will flash 3 times Hold the l button until the LivingColors displays a green light It is now connected to the remote control Repeat this procedure for every product you want to add to this remote control After connecting all of the products to the remote control you will be able to let them all change colour at the same time The same colour will be displayed by all of your LivingColors products by only us
Download Pdf Manuals
Related Search